| Message ID | 20210730144922.29111-3-semen.protsenko@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add minimal support for Exynos850 SoC | expand |
On 30/07/2021 16:49, Sam Protsenko wrote: > Add Samsung Exynos850 SoC specific data to enable pinctrl support for > all platforms based on Exynos850. > > Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> > --- > .../pinctrl/samsung/pinctrl-exynos-arm64.c | 129 ++++++++++++++++++ > drivers/pinctrl/samsung/pinctrl-exynos.h | 29 ++++ > drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + > drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + > 4 files changed, 161 insertions(+) > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > index b6e56422a700..9c71ff84ba7e 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > @@ -40,6 +40,24 @@ static const struct samsung_pin_bank_type exynos5433_bank_type_alive = { > .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, > }; > > +/* > + * Bank type for non-alive type. Bit fields: > + * CON: 4, DAT: 1, PUD: 4, DRV: 4, CONPDN: 2, PUDPDN: 4 > + */ > +static struct samsung_pin_bank_type exynos850_bank_type_off = { > + .fld_width = { 4, 1, 4, 4, 2, 4, }, > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, > +}; > + > +/* > + * Bank type for alive type. Bit fields: > + * CON: 4, DAT: 1, PUD: 4, DRV: 4 > + */ > +static struct samsung_pin_bank_type exynos850_bank_type_alive = { > + .fld_width = { 4, 1, 4, 4, }, > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, > +}; > + > /* Pad retention control code for accessing PMU regmap */ > static atomic_t exynos_shared_retention_refcnt; > > @@ -422,3 +440,114 @@ const struct samsung_pinctrl_of_match_data exynos7_of_data __initconst = { > .ctrl = exynos7_pin_ctrl, > .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), > }; > + > +/* pin banks of exynos850 pin-controller 0 (ALIVE) */ > +static struct samsung_pin_bank_data exynos850_pin_banks0[] = { > + /* Must start with EINTG banks, ordered by EINT group number. */ > + EXYNOS9_PIN_BANK_EINTW(8, 0x000, "gpa0", 0x00), Why EXYNOS9 not EXYNOS850? Is it really shared with 96xx, 98xx and 9x0 series? > + EXYNOS9_PIN_BANK_EINTW(8, 0x020, "gpa1", 0x04), > + EXYNOS9_PIN_BANK_EINTW(8, 0x040, "gpa2", 0x08), > + EXYNOS9_PIN_BANK_EINTW(8, 0x060, "gpa3", 0x0c), > + EXYNOS9_PIN_BANK_EINTW(4, 0x080, "gpa4", 0x10), > + EXYNOS9_PIN_BANK_EINTN(3, 0x0A0, "gpq0"), > +}; > + > +/* pin banks of exynos850 pin-controller 1 (CMGP) */ > +static struct samsung_pin_bank_data exynos850_pin_banks1[] = { > + /* Must start with EINTG banks, ordered by EINT group number. */ > + EXYNOS9_PIN_BANK_EINTW(1, 0x000, "gpm0", 0x00), > + EXYNOS9_PIN_BANK_EINTW(1, 0x020, "gpm1", 0x04), > + EXYNOS9_PIN_BANK_EINTW(1, 0x040, "gpm2", 0x08), > + EXYNOS9_PIN_BANK_EINTW(1, 0x060, "gpm3", 0x0C), > + EXYNOS9_PIN_BANK_EINTW(1, 0x080, "gpm4", 0x10), > + EXYNOS9_PIN_BANK_EINTW(1, 0x0A0, "gpm5", 0x14), > + EXYNOS9_PIN_BANK_EINTW(1, 0x0C0, "gpm6", 0x18), > + EXYNOS9_PIN_BANK_EINTW(1, 0x0E0, "gpm7", 0x1C), > +}; > + > +/* pin banks of exynos850 pin-controller 2 (AUD) */ > +static struct samsung_pin_bank_data exynos850_pin_banks2[] = { > + /* Must start with EINTG banks, ordered by EINT group number. */ > + EXYNOS9_PIN_BANK_EINTG(5, 0x000, "gpb0", 0x00), > + EXYNOS9_PIN_BANK_EINTG(5, 0x020, "gpb1", 0x04), > +}; > + > +/* pin banks of exynos850 pin-controller 3 (HSI) */ > +static struct samsung_pin_bank_data exynos850_pin_banks3[] = { > + /* Must start with EINTG banks, ordered by EINT group number. */ > + EXYNOS9_PIN_BANK_EINTG(6, 0x000, "gpf2", 0x00), > +}; > + > +/* pin banks of exynos850 pin-controller 4 (CORE) */ > +static struct samsung_pin_bank_data exynos850_pin_banks4[] = { > + /* Must start with EINTG banks, ordered by EINT group number. */ > + EXYNOS9_PIN_BANK_EINTG(4, 0x000, "gpf0", 0x00), > + EXYNOS9_PIN_BANK_EINTG(8, 0x020, "gpf1", 0x04), > +}; > + > +/* pin banks of exynos850 pin-controller 5 (PERI) */ > +static struct samsung_pin_bank_data exynos850_pin_banks5[] = { > + /* Must start with EINTG banks, ordered by EINT group number. */ > + EXYNOS9_PIN_BANK_EINTG(2, 0x000, "gpg0", 0x00), > + EXYNOS9_PIN_BANK_EINTG(6, 0x020, "gpp0", 0x04), > + EXYNOS9_PIN_BANK_EINTG(4, 0x040, "gpp1", 0x08), > + EXYNOS9_PIN_BANK_EINTG(4, 0x060, "gpp2", 0x0C), > + EXYNOS9_PIN_BANK_EINTG(8, 0x080, "gpg1", 0x10), > + EXYNOS9_PIN_BANK_EINTG(8, 0x0A0, "gpg2", 0x14), > + EXYNOS9_PIN_BANK_EINTG(1, 0x0C0, "gpg3", 0x18), > + EXYNOS9_PIN_BANK_EINTG(3, 0x0E0, "gpc0", 0x1C), > + EXYNOS9_PIN_BANK_EINTG(6, 0x100, "gpc1", 0x20), > +}; > + > +static const struct samsung_pin_ctrl exynos850_pin_ctrl[] __initconst = { > + { > + /* pin-controller instance 0 ALIVE data */ > + .pin_banks = exynos850_pin_banks0, > + .nr_banks = ARRAY_SIZE(exynos850_pin_banks0), > + .eint_gpio_init = exynos_eint_gpio_init, > + .eint_wkup_init = exynos_eint_wkup_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, I guess retention registers will follow sometime later. Best regards, Krzysztof
On Fri, 30 Jul 2021 at 18:22, Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> wrote: > > On 30/07/2021 16:49, Sam Protsenko wrote: > > Add Samsung Exynos850 SoC specific data to enable pinctrl support for > > all platforms based on Exynos850. > > > > Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> > > --- > > .../pinctrl/samsung/pinctrl-exynos-arm64.c | 129 ++++++++++++++++++ > > drivers/pinctrl/samsung/pinctrl-exynos.h | 29 ++++ > > drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + > > drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + > > 4 files changed, 161 insertions(+) > > > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > index b6e56422a700..9c71ff84ba7e 100644 > > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > @@ -40,6 +40,24 @@ static const struct samsung_pin_bank_type exynos5433_bank_type_alive = { > > .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, > > }; > > > > +/* > > + * Bank type for non-alive type. Bit fields: > > + * CON: 4, DAT: 1, PUD: 4, DRV: 4, CONPDN: 2, PUDPDN: 4 > > + */ > > +static struct samsung_pin_bank_type exynos850_bank_type_off = { > > + .fld_width = { 4, 1, 4, 4, 2, 4, }, > > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, > > +}; > > + > > +/* > > + * Bank type for alive type. Bit fields: > > + * CON: 4, DAT: 1, PUD: 4, DRV: 4 > > + */ > > +static struct samsung_pin_bank_type exynos850_bank_type_alive = { > > + .fld_width = { 4, 1, 4, 4, }, > > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, > > +}; > > + > > /* Pad retention control code for accessing PMU regmap */ > > static atomic_t exynos_shared_retention_refcnt; > > > > @@ -422,3 +440,114 @@ const struct samsung_pinctrl_of_match_data exynos7_of_data __initconst = { > > .ctrl = exynos7_pin_ctrl, > > .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), > > }; > > + > > +/* pin banks of exynos850 pin-controller 0 (ALIVE) */ > > +static struct samsung_pin_bank_data exynos850_pin_banks0[] = { > > + /* Must start with EINTG banks, ordered by EINT group number. */ > > + EXYNOS9_PIN_BANK_EINTW(8, 0x000, "gpa0", 0x00), > > Why EXYNOS9 not EXYNOS850? Is it really shared with 96xx, 98xx and 9x0 > series? > Yeah, I double checked and those macros are actually used for 96xx SoCs. So I suggest we leave it as is, as it seems to be related to the whole architecture series, not only to Exynos850. > > + EXYNOS9_PIN_BANK_EINTW(8, 0x020, "gpa1", 0x04), > > + EXYNOS9_PIN_BANK_EINTW(8, 0x040, "gpa2", 0x08), > > + EXYNOS9_PIN_BANK_EINTW(8, 0x060, "gpa3", 0x0c), > > + EXYNOS9_PIN_BANK_EINTW(4, 0x080, "gpa4", 0x10), > > + EXYNOS9_PIN_BANK_EINTN(3, 0x0A0, "gpq0"), > > +}; > > + > > +/* pin banks of exynos850 pin-controller 1 (CMGP) */ > > +static struct samsung_pin_bank_data exynos850_pin_banks1[] = { > > + /* Must start with EINTG banks, ordered by EINT group number. */ > > + EXYNOS9_PIN_BANK_EINTW(1, 0x000, "gpm0", 0x00), > > + EXYNOS9_PIN_BANK_EINTW(1, 0x020, "gpm1", 0x04), > > + EXYNOS9_PIN_BANK_EINTW(1, 0x040, "gpm2", 0x08), > > + EXYNOS9_PIN_BANK_EINTW(1, 0x060, "gpm3", 0x0C), > > + EXYNOS9_PIN_BANK_EINTW(1, 0x080, "gpm4", 0x10), > > + EXYNOS9_PIN_BANK_EINTW(1, 0x0A0, "gpm5", 0x14), > > + EXYNOS9_PIN_BANK_EINTW(1, 0x0C0, "gpm6", 0x18), > > + EXYNOS9_PIN_BANK_EINTW(1, 0x0E0, "gpm7", 0x1C), > > +}; > > + > > +/* pin banks of exynos850 pin-controller 2 (AUD) */ > > +static struct samsung_pin_bank_data exynos850_pin_banks2[] = { > > + /* Must start with EINTG banks, ordered by EINT group number. */ > > + EXYNOS9_PIN_BANK_EINTG(5, 0x000, "gpb0", 0x00), > > + EXYNOS9_PIN_BANK_EINTG(5, 0x020, "gpb1", 0x04), > > +}; > > + > > +/* pin banks of exynos850 pin-controller 3 (HSI) */ > > +static struct samsung_pin_bank_data exynos850_pin_banks3[] = { > > + /* Must start with EINTG banks, ordered by EINT group number. */ > > + EXYNOS9_PIN_BANK_EINTG(6, 0x000, "gpf2", 0x00), > > +}; > > + > > +/* pin banks of exynos850 pin-controller 4 (CORE) */ > > +static struct samsung_pin_bank_data exynos850_pin_banks4[] = { > > + /* Must start with EINTG banks, ordered by EINT group number. */ > > + EXYNOS9_PIN_BANK_EINTG(4, 0x000, "gpf0", 0x00), > > + EXYNOS9_PIN_BANK_EINTG(8, 0x020, "gpf1", 0x04), > > +}; > > + > > +/* pin banks of exynos850 pin-controller 5 (PERI) */ > > +static struct samsung_pin_bank_data exynos850_pin_banks5[] = { > > + /* Must start with EINTG banks, ordered by EINT group number. */ > > + EXYNOS9_PIN_BANK_EINTG(2, 0x000, "gpg0", 0x00), > > + EXYNOS9_PIN_BANK_EINTG(6, 0x020, "gpp0", 0x04), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x040, "gpp1", 0x08), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x060, "gpp2", 0x0C), > > + EXYNOS9_PIN_BANK_EINTG(8, 0x080, "gpg1", 0x10), > > + EXYNOS9_PIN_BANK_EINTG(8, 0x0A0, "gpg2", 0x14), > > + EXYNOS9_PIN_BANK_EINTG(1, 0x0C0, "gpg3", 0x18), > > + EXYNOS9_PIN_BANK_EINTG(3, 0x0E0, "gpc0", 0x1C), > > + EXYNOS9_PIN_BANK_EINTG(6, 0x100, "gpc1", 0x20), > > +}; > > + > > +static const struct samsung_pin_ctrl exynos850_pin_ctrl[] __initconst = { > > + { > > + /* pin-controller instance 0 ALIVE data */ > > + .pin_banks = exynos850_pin_banks0, > > + .nr_banks = ARRAY_SIZE(exynos850_pin_banks0), > > + .eint_gpio_init = exynos_eint_gpio_init, > > + .eint_wkup_init = exynos_eint_wkup_init, > > + .suspend = exynos_pinctrl_suspend, > > + .resume = exynos_pinctrl_resume, > > I guess retention registers will follow sometime later. > Good point, never noticed retention control is needed for suspend/resume to work properly. I will remove suspend/resume ops in v2, and PM support will be sent later. > Best regards, > Krzysztof
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c index b6e56422a700..9c71ff84ba7e 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c @@ -40,6 +40,24 @@ static const struct samsung_pin_bank_type exynos5433_bank_type_alive = { .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, }; +/* + * Bank type for non-alive type. Bit fields: + * CON: 4, DAT: 1, PUD: 4, DRV: 4, CONPDN: 2, PUDPDN: 4 + */ +static struct samsung_pin_bank_type exynos850_bank_type_off = { + .fld_width = { 4, 1, 4, 4, 2, 4, }, + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, +}; + +/* + * Bank type for alive type. Bit fields: + * CON: 4, DAT: 1, PUD: 4, DRV: 4 + */ +static struct samsung_pin_bank_type exynos850_bank_type_alive = { + .fld_width = { 4, 1, 4, 4, }, + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, +}; + /* Pad retention control code for accessing PMU regmap */ static atomic_t exynos_shared_retention_refcnt; @@ -422,3 +440,114 @@ const struct samsung_pinctrl_of_match_data exynos7_of_data __initconst = { .ctrl = exynos7_pin_ctrl, .num_ctrl = ARRAY_SIZE(exynos7_pin_ctrl), }; + +/* pin banks of exynos850 pin-controller 0 (ALIVE) */ +static struct samsung_pin_bank_data exynos850_pin_banks0[] = { + /* Must start with EINTG banks, ordered by EINT group number. */ + EXYNOS9_PIN_BANK_EINTW(8, 0x000, "gpa0", 0x00), + EXYNOS9_PIN_BANK_EINTW(8, 0x020, "gpa1", 0x04), + EXYNOS9_PIN_BANK_EINTW(8, 0x040, "gpa2", 0x08), + EXYNOS9_PIN_BANK_EINTW(8, 0x060, "gpa3", 0x0c), + EXYNOS9_PIN_BANK_EINTW(4, 0x080, "gpa4", 0x10), + EXYNOS9_PIN_BANK_EINTN(3, 0x0A0, "gpq0"), +}; + +/* pin banks of exynos850 pin-controller 1 (CMGP) */ +static struct samsung_pin_bank_data exynos850_pin_banks1[] = { + /* Must start with EINTG banks, ordered by EINT group number. */ + EXYNOS9_PIN_BANK_EINTW(1, 0x000, "gpm0", 0x00), + EXYNOS9_PIN_BANK_EINTW(1, 0x020, "gpm1", 0x04), + EXYNOS9_PIN_BANK_EINTW(1, 0x040, "gpm2", 0x08), + EXYNOS9_PIN_BANK_EINTW(1, 0x060, "gpm3", 0x0C), + EXYNOS9_PIN_BANK_EINTW(1, 0x080, "gpm4", 0x10), + EXYNOS9_PIN_BANK_EINTW(1, 0x0A0, "gpm5", 0x14), + EXYNOS9_PIN_BANK_EINTW(1, 0x0C0, "gpm6", 0x18), + EXYNOS9_PIN_BANK_EINTW(1, 0x0E0, "gpm7", 0x1C), +}; + +/* pin banks of exynos850 pin-controller 2 (AUD) */ +static struct samsung_pin_bank_data exynos850_pin_banks2[] = { + /* Must start with EINTG banks, ordered by EINT group number. */ + EXYNOS9_PIN_BANK_EINTG(5, 0x000, "gpb0", 0x00), + EXYNOS9_PIN_BANK_EINTG(5, 0x020, "gpb1", 0x04), +}; + +/* pin banks of exynos850 pin-controller 3 (HSI) */ +static struct samsung_pin_bank_data exynos850_pin_banks3[] = { + /* Must start with EINTG banks, ordered by EINT group number. */ + EXYNOS9_PIN_BANK_EINTG(6, 0x000, "gpf2", 0x00), +}; + +/* pin banks of exynos850 pin-controller 4 (CORE) */ +static struct samsung_pin_bank_data exynos850_pin_banks4[] = { + /* Must start with EINTG banks, ordered by EINT group number. */ + EXYNOS9_PIN_BANK_EINTG(4, 0x000, "gpf0", 0x00), + EXYNOS9_PIN_BANK_EINTG(8, 0x020, "gpf1", 0x04), +}; + +/* pin banks of exynos850 pin-controller 5 (PERI) */ +static struct samsung_pin_bank_data exynos850_pin_banks5[] = { + /* Must start with EINTG banks, ordered by EINT group number. */ + EXYNOS9_PIN_BANK_EINTG(2, 0x000, "gpg0", 0x00), + EXYNOS9_PIN_BANK_EINTG(6, 0x020, "gpp0", 0x04), + EXYNOS9_PIN_BANK_EINTG(4, 0x040, "gpp1", 0x08), + EXYNOS9_PIN_BANK_EINTG(4, 0x060, "gpp2", 0x0C), + EXYNOS9_PIN_BANK_EINTG(8, 0x080, "gpg1", 0x10), + EXYNOS9_PIN_BANK_EINTG(8, 0x0A0, "gpg2", 0x14), + EXYNOS9_PIN_BANK_EINTG(1, 0x0C0, "gpg3", 0x18), + EXYNOS9_PIN_BANK_EINTG(3, 0x0E0, "gpc0", 0x1C), + EXYNOS9_PIN_BANK_EINTG(6, 0x100, "gpc1", 0x20), +}; + +static const struct samsung_pin_ctrl exynos850_pin_ctrl[] __initconst = { + { + /* pin-controller instance 0 ALIVE data */ + .pin_banks = exynos850_pin_banks0, + .nr_banks = ARRAY_SIZE(exynos850_pin_banks0), + .eint_gpio_init = exynos_eint_gpio_init, + .eint_wkup_init = exynos_eint_wkup_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin-controller instance 1 CMGP data */ + .pin_banks = exynos850_pin_banks1, + .nr_banks = ARRAY_SIZE(exynos850_pin_banks1), + .eint_gpio_init = exynos_eint_gpio_init, + .eint_wkup_init = exynos_eint_wkup_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin-controller instance 2 AUD data */ + .pin_banks = exynos850_pin_banks2, + .nr_banks = ARRAY_SIZE(exynos850_pin_banks2), + .eint_gpio_init = exynos_eint_gpio_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin-controller instance 3 HSI data */ + .pin_banks = exynos850_pin_banks3, + .nr_banks = ARRAY_SIZE(exynos850_pin_banks3), + .eint_gpio_init = exynos_eint_gpio_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin-controller instance 4 CORE data */ + .pin_banks = exynos850_pin_banks4, + .nr_banks = ARRAY_SIZE(exynos850_pin_banks4), + .eint_gpio_init = exynos_eint_gpio_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin-controller instance 5 PERI data */ + .pin_banks = exynos850_pin_banks5, + .nr_banks = ARRAY_SIZE(exynos850_pin_banks5), + .eint_gpio_init = exynos_eint_gpio_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, +}; + +const struct samsung_pinctrl_of_match_data exynos850_of_data __initconst = { + .ctrl = exynos850_pin_ctrl, + .num_ctrl = ARRAY_SIZE(exynos850_pin_ctrl), +}; diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h index da1ec13697e7..595086f2d5dd 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos.h +++ b/drivers/pinctrl/samsung/pinctrl-exynos.h @@ -108,6 +108,35 @@ .pctl_res_idx = pctl_idx, \ } \ +#define EXYNOS9_PIN_BANK_EINTN(pins, reg, id) \ + { \ + .type = &exynos850_bank_type_alive, \ + .pctl_offset = reg, \ + .nr_pins = pins, \ + .eint_type = EINT_TYPE_NONE, \ + .name = id \ + } + +#define EXYNOS9_PIN_BANK_EINTG(pins, reg, id, offs) \ + { \ + .type = &exynos850_bank_type_off, \ + .pctl_offset = reg, \ + .nr_pins = pins, \ + .eint_type = EINT_TYPE_GPIO, \ + .eint_offset = offs, \ + .name = id \ + } + +#define EXYNOS9_PIN_BANK_EINTW(pins, reg, id, offs) \ + { \ + .type = &exynos850_bank_type_alive, \ + .pctl_offset = reg, \ + .nr_pins = pins, \ + .eint_type = EINT_TYPE_WKUP, \ + .eint_offset = offs, \ + .name = id \ + } + /** * struct exynos_weint_data: irq specific data for all the wakeup interrupts * generated by the external wakeup interrupt controller. diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c index 2975b4369f32..2a0fc63516f1 100644 --- a/drivers/pinctrl/samsung/pinctrl-samsung.c +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c @@ -1264,6 +1264,8 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = { .data = &exynos5433_of_data }, { .compatible = "samsung,exynos7-pinctrl", .data = &exynos7_of_data }, + { .compatible = "samsung,exynos850-pinctrl", + .data = &exynos850_of_data }, #endif #ifdef CONFIG_PINCTRL_S3C64XX { .compatible = "samsung,s3c64xx-pinctrl", diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h index de44f8ec330b..4c2149e9c544 100644 --- a/drivers/pinctrl/samsung/pinctrl-samsung.h +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h @@ -339,6 +339,7 @@ extern const struct samsung_pinctrl_of_match_data exynos5410_of_data; extern const struct samsung_pinctrl_of_match_data exynos5420_of_data; extern const struct samsung_pinctrl_of_match_data exynos5433_of_data; extern const struct samsung_pinctrl_of_match_data exynos7_of_data; +extern const struct samsung_pinctrl_of_match_data exynos850_of_data; extern const struct samsung_pinctrl_of_match_data s3c64xx_of_data; extern const struct samsung_pinctrl_of_match_data s3c2412_of_data; extern const struct samsung_pinctrl_of_match_data s3c2416_of_data;
Add Samsung Exynos850 SoC specific data to enable pinctrl support for all platforms based on Exynos850. Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> --- .../pinctrl/samsung/pinctrl-exynos-arm64.c | 129 ++++++++++++++++++ drivers/pinctrl/samsung/pinctrl-exynos.h | 29 ++++ drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + 4 files changed, 161 insertions(+)