| Message ID | 20210904142745.183875-5-adeep@lexina.in (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: meson: add support for JetHub D1/H1 | expand |
On 04/09/2021 16:27, Vyacheslav Bocharov wrote: > JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation > controller with the following features: > - DIN Rail Mounting > - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz > - no video out > - 512Mb/1GB LPDDR4 > - 8/16GB eMMC flash > - 1 x USB 2.0 > - 1 x 10/100Mbps ethernet > - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, > Bluetooth 4.2. > - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power > and Zigbee 3.0 support. > - 2 x gpio LEDS > - GPIO user Button > - 1 x 1-Wire > - 2 x RS-485 > - 4 x dry contact digital GPIO inputs > - 3 x relay GPIO outputs > - DC source with a voltage of 9 to 56 V / Passive POE > > Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in> > --- > arch/arm64/boot/dts/amlogic/Makefile | 1 + > .../amlogic/meson-axg-jethome-jethub-j100.dts | 354 ++++++++++++++++++ > 2 files changed, 355 insertions(+) > create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts > > diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile > index 2c3ce7c401a5..3ba6f58b9833 100644 > --- a/arch/arm64/boot/dts/amlogic/Makefile > +++ b/arch/arm64/boot/dts/amlogic/Makefile > @@ -1,5 +1,6 @@ > # SPDX-License-Identifier: GPL-2.0 > dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb > +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb > diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts > new file mode 100644 > index 000000000000..bc10f3357c09 > --- /dev/null > +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts > @@ -0,0 +1,354 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in> > + * Copyright (c) 2020 JetHome > + * Author: Aleksandr Kazantsev <ak@tvip.ru> > + * Author: Alexey Shevelkin <ash@tvip.ru> > + * Author: Vyacheslav Bocharov <adeep@lexina.in> > + */ > + > +/dts-v1/; > + > +#include "meson-axg.dtsi" > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/thermal/thermal.h> > + > +/ { > + compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg"; > + model = "JetHome JetHub J100"; > + aliases { > + serial0 = &uart_AO; /* Console */ > + serial1 = &uart_AO_B; /* External UART (Wireless Module) */ > + ethernet0 = ðmac; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + /* 1024MB RAM */ > + memory@0 { > + device_type = "memory"; > + reg = <0x0 0x0 0x0 0x40000000>; > + }; > + > + reserved-memory { > + linux,cma { > + size = <0x0 0x400000>; > + }; > + }; > + > + emmc_pwrseq: emmc-pwrseq { > + compatible = "mmc-pwrseq-emmc"; > + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; > + }; > + > + vcc_3v3: regulator-vcc_3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "VCC_3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vddao_3v3>; > + regulator-always-on; > + }; > + > + vcc_5v: regulator-vcc_5v { > + compatible = "regulator-fixed"; > + regulator-name = "VCC5V"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + vddao_3v3: regulator-vddao_3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "VDDAO_3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&vcc_5v>; > + regulator-always-on; > + }; > + > + vddio_ao18: regulator-vddio_ao18 { > + compatible = "regulator-fixed"; > + regulator-name = "VDDIO_AO18"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vddao_3v3>; > + regulator-always-on; > + }; > + > + vddio_boot: regulator-vddio_boot { > + compatible = "regulator-fixed"; > + regulator-name = "VDDIO_BOOT"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vddao_3v3>; > + regulator-always-on; > + }; > + > + usb_pwr: regulator-usb_pwr { > + compatible = "regulator-fixed"; > + regulator-name = "USB_PWR"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + vin-supply = <&vcc_5v>; > + regulator-always-on; > + }; > + > + sdio_pwrseq: sdio-pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>; > + clocks = <&wifi32k>; > + clock-names = "ext_clock"; > + }; > + > + wifi32k: wifi32k { > + compatible = "pwm-clock"; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */ > + }; > + > + thermal-zones { > + cpu_thermal: cpu-thermal { > + polling-delay-passive = <250>; > + polling-delay = <1000>; > + thermal-sensors = <&scpi_sensors 0>; > + trips { > + cpu_passive: cpu-passive { > + temperature = <70000>; /* millicelsius */ > + hysteresis = <2000>; /* millicelsius */ > + type = "passive"; > + }; > + > + cpu_hot: cpu-hot { > + temperature = <80000>; /* millicelsius */ > + hysteresis = <2000>; /* millicelsius */ > + type = "hot"; > + }; > + > + cpu_critical: cpu-critical { > + temperature = <100000>; /* millicelsius */ > + hysteresis = <2000>; /* millicelsius */ > + type = "critical"; > + }; > + }; > + }; > + > + cpu_cooling_maps: cooling-maps { > + map0 { > + trip = <&cpu_passive>; > + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + > + map1 { > + trip = <&cpu_hot>; > + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, > + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; > + }; > + }; > + }; > +}; > + > +&efuse { > + sn: sn@32 { > + reg = <0x32 0x20>; > + }; > + > + eth_mac: eth_mac@0 { > + reg = <0x0 0x6>; > + }; > + > + bt_mac: bt_mac@6 { > + reg = <0x6 0x6>; > + }; > + > + wifi_mac: wifi_mac@c { > + reg = <0xc 0x6>; > + }; > + > + bid: bid@12 { > + reg = <0x12 0x20>; > + }; > +}; > + > +ðmac { > + status = "okay"; > + pinctrl-0 = <ð_rmii_x_pins>; > + pinctrl-names = "default"; > + phy-handle = <ð_phy0>; > + phy-mode = "rmii"; > + > + mdio { > + compatible = "snps,dwmac-mdio"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */ > + eth_phy0: ethernet-phy@0 { > + /* compatible = "ethernet-phy-id0243.0c54";*/ > + max-speed = <100>; > + reg = <0>; > + > + reset-assert-us = <10000>; > + reset-deassert-us = <10000>; > + reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>; > + }; > + }; > +}; > + > +/* Internal I2C bus (on CPU module) */ > +&i2c1 { > + status = "okay"; > + pinctrl-0 = <&i2c1_z_pins>; > + pinctrl-names = "default"; > + > + /* RTC */ > + pcf8563: pcf8563@51 { > + compatible = "nxp,pcf8563"; > + reg = <0x51>; > + status = "okay"; > + }; > +}; > + > +/* Peripheral I2C bus (on motherboard) */ > +&i2c_AO { > + status = "okay"; > + pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>; > + pinctrl-names = "default"; > +}; > + > +&pwm_ab { > + status = "okay"; > + pinctrl-0 = <&pwm_a_x20_pins>; > + pinctrl-names = "default"; > +}; > + > +/* wifi module */ > +&sd_emmc_b { > + status = "okay"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + pinctrl-0 = <&sdio_pins>; > + pinctrl-1 = <&sdio_clk_gate_pins>; > + pinctrl-names = "default", "clk-gate"; > + > + bus-width = <4>; > + cap-sd-highspeed; > + sd-uhs-sdr104; > + max-frequency = <200000000>; > + non-removable; > + disable-wp; > + > + mmc-pwrseq = <&sdio_pwrseq>; > + > + vmmc-supply = <&vddao_3v3>; > + vqmmc-supply = <&vddio_boot>; > + > + brcmf: wifi@1 { > + reg = <1>; > + compatible = "brcm,bcm4329-fmac"; > + }; > +}; > + > +/* emmc storage */ > +&sd_emmc_c { > + status = "okay"; > + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; > + pinctrl-1 = <&emmc_clk_gate_pins>; > + pinctrl-names = "default", "clk-gate"; > + > + bus-width = <8>; > + cap-mmc-highspeed; > + max-frequency = <200000000>; > + non-removable; > + disable-wp; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + > + mmc-pwrseq = <&emmc_pwrseq>; > + > + vmmc-supply = <&vcc_3v3>; > + vqmmc-supply = <&vddio_boot>; > +}; > + > +/* UART Bluetooth */ > +&uart_B { > + status = "okay"; > + pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>; > + pinctrl-names = "default"; > + uart-has-rtscts; > + > + bluetooth { > + compatible = "brcm,bcm43438-bt"; > + shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>; > + }; > +}; > + > +/* UART Console */ > +&uart_AO { > + status = "okay"; > + pinctrl-0 = <&uart_ao_a_pins>; > + pinctrl-names = "default"; > +}; > + > +/* UART Wireless module */ > +&uart_AO_B { > + status = "okay"; > + pinctrl-0 = <&uart_ao_b_pins>; > + pinctrl-names = "default"; > +}; > + > +&usb { > + status = "okay"; > + phy-supply = <&usb_pwr>; > +}; > + > +&spicc1 { > + status = "okay"; > +}; Why enabling it without pinctrl properties ? > + > +&gpio { > + gpio-line-names = > + "", "", "", "", "", // 0 - 4 > + "", "", "", "", "", // 5 - 9 > + "UserButton", "", "", "", "", // 10 - 14 > + "", "", "", "", "", // 15 - 19 > + "", "", "", "", "", // 20 - 24 > + "", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29 > + "Output1", "", "", "", "", // 30 - 34 > + "", "ZigBeeBOOT", "", "", "", // 35 - 39 > + "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44 > + "Input2", "Input1", "", "", "", // 45 - 49 > + "", "", "", "", "", // 50 - 54 > + "", "", "", "", "", // 55 - 59 > + "", "", "", "", "", // 60 - 64 > + "", "", "", "", "", // 65 - 69 > + "", "", "", "", "", // 70 - 74 > + "", "", "", "", "", // 75 - 79 > + "", "", "", "", "", // 80 - 84 > + "", ""; // 85-86 > +}; > + > +&cpu0 { > + #cooling-cells = <2>; > +}; > + > +&cpu1 { > + #cooling-cells = <2>; > +}; > + > +&cpu2 { > + #cooling-cells = <2>; > +}; > + > +&cpu3 { > + #cooling-cells = <2>; > +}; > Apart the spicc node without properties, it looks good. Neil
06.09.2021 15:26, Neil Armstrong пишет: > On 04/09/2021 16:27, Vyacheslav Bocharov wrote: >> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation >> controller with the following features: >> >> + >> +&spicc1 { >> + status = "okay"; >> +}; > Why enabling it without pinctrl properties ? spiccwas planned for use during the development of the device, but in fact it is not currently used. Pins exist on expand pad. Its better to add pinctrl as below or leave spicc1 disabled? diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts index bc10f3357c09..ecffc90d9884 100644 --- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts @@ -313,6 +313,8 @@ &usb { &spicc1 { status = "okay"; + pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>; + pinctrl-names = "default"; }; &gpio { -- Vyacheslav
Hi, On 06/09/2021 17:07, Vyacheslav wrote: > 06.09.2021 15:26, Neil Armstrong пишет: >> On 04/09/2021 16:27, Vyacheslav Bocharov wrote: >>> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation >>> controller with the following features: >>> >>> + >>> +&spicc1 { >>> + status = "okay"; >>> +}; >> Why enabling it without pinctrl properties ? > > spiccwas planned for use during the development of the device, but in fact it is not currently used. Pins exist on expand pad. > > Its better to add pinctrl as below or leave spicc1 disabled? As you want, if the HW is present and functional, usually it's enabled in the DT. Neil > > diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts > index bc10f3357c09..ecffc90d9884 100644 > --- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts > +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts > @@ -313,6 +313,8 @@ &usb { > > &spicc1 { > status = "okay"; > + pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>; > + pinctrl-names = "default"; > }; > > &gpio { > > > -- > > Vyacheslav >
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index 2c3ce7c401a5..3ba6f58b9833 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts new file mode 100644 index 000000000000..bc10f3357c09 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts @@ -0,0 +1,354 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in> + * Copyright (c) 2020 JetHome + * Author: Aleksandr Kazantsev <ak@tvip.ru> + * Author: Alexey Shevelkin <ash@tvip.ru> + * Author: Vyacheslav Bocharov <adeep@lexina.in> + */ + +/dts-v1/; + +#include "meson-axg.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg"; + model = "JetHome JetHub J100"; + aliases { + serial0 = &uart_AO; /* Console */ + serial1 = &uart_AO_B; /* External UART (Wireless Module) */ + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + /* 1024MB RAM */ + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + reserved-memory { + linux,cma { + size = <0x0 0x400000>; + }; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "VCC5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_5v>; + regulator-always-on; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + usb_pwr: regulator-usb_pwr { + compatible = "regulator-fixed"; + regulator-name = "USB_PWR"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + regulator-always-on; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */ + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + thermal-sensors = <&scpi_sensors 0>; + trips { + cpu_passive: cpu-passive { + temperature = <70000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + + cpu_hot: cpu-hot { + temperature = <80000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "hot"; + }; + + cpu_critical: cpu-critical { + temperature = <100000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_passive>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + + map1 { + trip = <&cpu_hot>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; +}; + +&efuse { + sn: sn@32 { + reg = <0x32 0x20>; + }; + + eth_mac: eth_mac@0 { + reg = <0x0 0x6>; + }; + + bt_mac: bt_mac@6 { + reg = <0x6 0x6>; + }; + + wifi_mac: wifi_mac@c { + reg = <0xc 0x6>; + }; + + bid: bid@12 { + reg = <0x12 0x20>; + }; +}; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_rmii_x_pins>; + pinctrl-names = "default"; + phy-handle = <ð_phy0>; + phy-mode = "rmii"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */ + eth_phy0: ethernet-phy@0 { + /* compatible = "ethernet-phy-id0243.0c54";*/ + max-speed = <100>; + reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>; + }; + }; +}; + +/* Internal I2C bus (on CPU module) */ +&i2c1 { + status = "okay"; + pinctrl-0 = <&i2c1_z_pins>; + pinctrl-names = "default"; + + /* RTC */ + pcf8563: pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + status = "okay"; + }; +}; + +/* Peripheral I2C bus (on motherboard) */ +&i2c_AO { + status = "okay"; + pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>; + pinctrl-names = "default"; +}; + +&pwm_ab { + status = "okay"; + pinctrl-0 = <&pwm_a_x20_pins>; + pinctrl-names = "default"; +}; + +/* wifi module */ +&sd_emmc_b { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr104; + max-frequency = <200000000>; + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* emmc storage */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + max-frequency = <200000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* UART Bluetooth */ +&uart_B { + status = "okay"; + pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>; + }; +}; + +/* UART Console */ +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +/* UART Wireless module */ +&uart_AO_B { + status = "okay"; + pinctrl-0 = <&uart_ao_b_pins>; + pinctrl-names = "default"; +}; + +&usb { + status = "okay"; + phy-supply = <&usb_pwr>; +}; + +&spicc1 { + status = "okay"; +}; + +&gpio { + gpio-line-names = + "", "", "", "", "", // 0 - 4 + "", "", "", "", "", // 5 - 9 + "UserButton", "", "", "", "", // 10 - 14 + "", "", "", "", "", // 15 - 19 + "", "", "", "", "", // 20 - 24 + "", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29 + "Output1", "", "", "", "", // 30 - 34 + "", "ZigBeeBOOT", "", "", "", // 35 - 39 + "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44 + "Input2", "Input1", "", "", "", // 45 - 49 + "", "", "", "", "", // 50 - 54 + "", "", "", "", "", // 55 - 59 + "", "", "", "", "", // 60 - 64 + "", "", "", "", "", // 65 - 69 + "", "", "", "", "", // 70 - 74 + "", "", "", "", "", // 75 - 79 + "", "", "", "", "", // 80 - 84 + "", ""; // 85-86 +}; + +&cpu0 { + #cooling-cells = <2>; +}; + +&cpu1 { + #cooling-cells = <2>; +}; + +&cpu2 { + #cooling-cells = <2>; +}; + +&cpu3 { + #cooling-cells = <2>; +};
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features: - DIN Rail Mounting - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz - no video out - 512Mb/1GB LPDDR4 - 8/16GB eMMC flash - 1 x USB 2.0 - 1 x 10/100Mbps ethernet - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2. - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support. - 2 x gpio LEDS - GPIO user Button - 1 x 1-Wire - 2 x RS-485 - 4 x dry contact digital GPIO inputs - 3 x relay GPIO outputs - DC source with a voltage of 9 to 56 V / Passive POE Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in> --- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../amlogic/meson-axg-jethome-jethub-j100.dts | 354 ++++++++++++++++++ 2 files changed, 355 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts