| Message ID | 569dc85d8058e2884d76ab36c6c46d36e7ad8555.1630583382.git.mchehab+huawei@kernel.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add DTS bits to enable USB3 PHY on HiKey970 | expand |
Hi Mauro, On 2021/9/2 19:55, Mauro Carvalho Chehab wrote: > Add the USB3 bindings for Kirin 970 phy and Hikey 970 board. > > Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> > --- > .../boot/dts/hisilicon/hi3670-hikey970.dts | 83 +++++++++++++++++++ > arch/arm64/boot/dts/hisilicon/hi3670.dtsi | 56 +++++++++++++ > 2 files changed, 139 insertions(+) > > diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts > index 7c32f5fd5cc5..60594db07041 100644 > --- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts > +++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts > @@ -430,3 +430,86 @@ &uart6 { > label = "LS-UART1"; > status = "okay"; > }; > + > +&usb_phy { > + phy-supply = <&ldo17>; > +}; > + > +&i2c1 { > + status = "okay"; > + > + rt1711h: rt1711h@4e { > + compatible = "richtek,rt1711h"; > + reg = <0x4e>; > + status = "okay"; > + interrupt-parent = <&gpio27>; > + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; > + pinctrl-names = "default"; > + pinctrl-0 = <&usb_cfg_func>; > + > + usb_con: connector { > + compatible = "usb-c-connector"; > + label = "USB-C"; > + data-role = "dual"; > + power-role = "dual"; > + try-power-role = "sink"; > + source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>; > + sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM) > + PDO_VAR(5000, 5000, 1000)>; > + op-sink-microwatt = <10000000>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + port@1 { > + reg = <1>; > + usb_con_ss: endpoint { > + remote-endpoint = <&dwc3_ss>; > + }; > + }; > + }; > + }; > + port { > + #address-cells = <1>; > + #size-cells = <0>; > + > + rt1711h_ep: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&hikey_usb_ep1>; The 'hikey_usb_ep1' is not defined yet. > + }; > + }; > + }; > +}; > + > +&i2c2 { > + /* USB HUB is on this bus at address 0x44 */ > + status = "okay"; > +}; > + > +&dwc3 { /* USB */ > + dr_mode = "otg"; > + maximum-speed = "super-speed"; > + phy_type = "utmi"; > + snps,dis-del-phy-power-chg-quirk; > + snps,dis_u2_susphy_quirk; > + snps,dis_u3_susphy_quirk; > + snps,tx_de_emphasis_quirk; > + snps,tx_de_emphasis = <1>; > + snps,dis-split-quirk; > + snps,gctl-reset-quirk; > + usb-role-switch; > + role-switch-default-mode = "host"; > + port { > + #address-cells = <1>; > + #size-cells = <0>; > + dwc3_role_switch: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&hikey_usb_ep0>; Ditto. The 'hikey_usb_ep0' is not defined yet. > + }; > + > + dwc3_ss: endpoint@1 { > + reg = <1>; > + remote-endpoint = <&usb_con_ss>; > + }; > + }; > +}; > diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi > index 636c8817df7e..782e1487666d 100644 > --- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi > +++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi > @@ -8,6 +8,7 @@ > > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/clock/hi3670-clock.h> > +#include <dt-bindings/usb/pd.h> > > / { > compatible = "hisilicon,hi3670"; > @@ -785,5 +786,60 @@ i2c4: i2c@fdf0d000 { > pinctrl-0 = <&i2c4_pmx_func &i2c4_cfg_func>; > status = "disabled"; > }; > + > + usb3_otg_bc: usb3_otg_bc@ff200000 { > + compatible = "syscon", "simple-mfd"; > + reg = <0x0 0xff200000 0x0 0x1000>; > + > + usb_phy: usbphy { > + compatible = "hisilicon,hi3670-usb-phy"; > + #phy-cells = <0>; > + hisilicon,pericrg-syscon = <&crg_ctrl>; > + hisilicon,pctrl-syscon = <&pctrl>; > + hisilicon,sctrl-syscon = <&sctrl>; > + hisilicon,eye-diagram-param = <0xFDFEE4>; > + hisilicon,tx-vboost-lvl = <0x5>; > + }; > + }; > + > + usb31_misc_rst: usb31_misc_rst_controller { > + compatible = "hisilicon,hi3660-reset"; > + #reset-cells = <2>; > + hisi,rst-syscon = <&usb3_otg_bc>; > + }; > + > + usb3: hisi_dwc3 { > + compatible = "hisilicon,hi3670-dwc3"; Is it OK to add the 'hi3670-dwc3' into the devicetree binding document? Thanks! Best Regards, Wei > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + clocks = <&crg_ctrl HI3670_CLK_GATE_ABB_USB>, > + <&crg_ctrl HI3670_HCLK_GATE_USB3OTG>, > + <&crg_ctrl HI3670_CLK_GATE_USB3OTG_REF>, > + <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>; > + clock-names = "clk_gate_abb_usb", > + "hclk_gate_usb3otg", > + "clk_gate_usb3otg_ref", > + "aclk_gate_usb3dvfs"; > + > + assigned-clocks = <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>; > + assigned-clock-rates = <238000000>; > + resets = <&crg_rst 0x90 6>, > + <&crg_rst 0x90 7>, > + <&usb31_misc_rst 0xA0 8>, > + <&usb31_misc_rst 0xA0 9>; > + > + dwc3: usb@ff100000 { > + compatible = "snps,dwc3"; > + reg = <0x0 0xff100000 0x0 0x100000>; > + > + interrupts = <0 159 IRQ_TYPE_LEVEL_HIGH>, > + <0 161 IRQ_TYPE_LEVEL_HIGH>; > + > + phys = <&usb_phy>; > + phy-names = "usb3-phy"; > + }; > + }; > }; > }; >
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts index 7c32f5fd5cc5..60594db07041 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts +++ b/arch/arm64/boot/dts/hisilicon/hi3670-hikey970.dts @@ -430,3 +430,86 @@ &uart6 { label = "LS-UART1"; status = "okay"; }; + +&usb_phy { + phy-supply = <&ldo17>; +}; + +&i2c1 { + status = "okay"; + + rt1711h: rt1711h@4e { + compatible = "richtek,rt1711h"; + reg = <0x4e>; + status = "okay"; + interrupt-parent = <&gpio27>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_cfg_func>; + + usb_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 5000, 1000)>; + op-sink-microwatt = <10000000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@1 { + reg = <1>; + usb_con_ss: endpoint { + remote-endpoint = <&dwc3_ss>; + }; + }; + }; + }; + port { + #address-cells = <1>; + #size-cells = <0>; + + rt1711h_ep: endpoint@0 { + reg = <0>; + remote-endpoint = <&hikey_usb_ep1>; + }; + }; + }; +}; + +&i2c2 { + /* USB HUB is on this bus at address 0x44 */ + status = "okay"; +}; + +&dwc3 { /* USB */ + dr_mode = "otg"; + maximum-speed = "super-speed"; + phy_type = "utmi"; + snps,dis-del-phy-power-chg-quirk; + snps,dis_u2_susphy_quirk; + snps,dis_u3_susphy_quirk; + snps,tx_de_emphasis_quirk; + snps,tx_de_emphasis = <1>; + snps,dis-split-quirk; + snps,gctl-reset-quirk; + usb-role-switch; + role-switch-default-mode = "host"; + port { + #address-cells = <1>; + #size-cells = <0>; + dwc3_role_switch: endpoint@0 { + reg = <0>; + remote-endpoint = <&hikey_usb_ep0>; + }; + + dwc3_ss: endpoint@1 { + reg = <1>; + remote-endpoint = <&usb_con_ss>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi index 636c8817df7e..782e1487666d 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi @@ -8,6 +8,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/hi3670-clock.h> +#include <dt-bindings/usb/pd.h> / { compatible = "hisilicon,hi3670"; @@ -785,5 +786,60 @@ i2c4: i2c@fdf0d000 { pinctrl-0 = <&i2c4_pmx_func &i2c4_cfg_func>; status = "disabled"; }; + + usb3_otg_bc: usb3_otg_bc@ff200000 { + compatible = "syscon", "simple-mfd"; + reg = <0x0 0xff200000 0x0 0x1000>; + + usb_phy: usbphy { + compatible = "hisilicon,hi3670-usb-phy"; + #phy-cells = <0>; + hisilicon,pericrg-syscon = <&crg_ctrl>; + hisilicon,pctrl-syscon = <&pctrl>; + hisilicon,sctrl-syscon = <&sctrl>; + hisilicon,eye-diagram-param = <0xFDFEE4>; + hisilicon,tx-vboost-lvl = <0x5>; + }; + }; + + usb31_misc_rst: usb31_misc_rst_controller { + compatible = "hisilicon,hi3660-reset"; + #reset-cells = <2>; + hisi,rst-syscon = <&usb3_otg_bc>; + }; + + usb3: hisi_dwc3 { + compatible = "hisilicon,hi3670-dwc3"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&crg_ctrl HI3670_CLK_GATE_ABB_USB>, + <&crg_ctrl HI3670_HCLK_GATE_USB3OTG>, + <&crg_ctrl HI3670_CLK_GATE_USB3OTG_REF>, + <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>; + clock-names = "clk_gate_abb_usb", + "hclk_gate_usb3otg", + "clk_gate_usb3otg_ref", + "aclk_gate_usb3dvfs"; + + assigned-clocks = <&crg_ctrl HI3670_ACLK_GATE_USB3DVFS>; + assigned-clock-rates = <238000000>; + resets = <&crg_rst 0x90 6>, + <&crg_rst 0x90 7>, + <&usb31_misc_rst 0xA0 8>, + <&usb31_misc_rst 0xA0 9>; + + dwc3: usb@ff100000 { + compatible = "snps,dwc3"; + reg = <0x0 0xff100000 0x0 0x100000>; + + interrupts = <0 159 IRQ_TYPE_LEVEL_HIGH>, + <0 161 IRQ_TYPE_LEVEL_HIGH>; + + phys = <&usb_phy>; + phy-names = "usb3-phy"; + }; + }; }; };
Add the USB3 bindings for Kirin 970 phy and Hikey 970 board. Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> --- .../boot/dts/hisilicon/hi3670-hikey970.dts | 83 +++++++++++++++++++ arch/arm64/boot/dts/hisilicon/hi3670.dtsi | 56 +++++++++++++ 2 files changed, 139 insertions(+)