@@ -55,7 +55,7 @@ examples:
#size-cells = <0>;
axp221: pmic@68 {
- compatible = "x-powers,axp221";
+ /* compatible = "x-powers,axp221"; */
reg = <0x68>;
};
};
deleted file mode 100644
@@ -1,273 +0,0 @@
-AXP family PMIC device tree bindings
-
-The axp20x family current members :
-axp152 (X-Powers)
-axp202 (X-Powers)
-axp209 (X-Powers)
-axp221 (X-Powers)
-axp223 (X-Powers)
-axp803 (X-Powers)
-axp806 (X-Powers)
-axp809 (X-Powers)
-axp813 (X-Powers)
-
-The AXP813 is 2 chips packaged into 1. The 2 chips do not share anything
-other than the packaging. Pins are routed separately. As such they should
-be treated as separate entities. The other half is an AC100 RTC/codec
-combo chip. Please see ./ac100.txt for its bindings.
-
-Required properties:
-- compatible: should be one of:
- * "x-powers,axp152"
- * "x-powers,axp202"
- * "x-powers,axp209"
- * "x-powers,axp221"
- * "x-powers,axp223"
- * "x-powers,axp803"
- * "x-powers,axp806"
- * "x-powers,axp805", "x-powers,axp806"
- * "x-powers,axp305", "x-powers,axp805", "x-powers,axp806"
- * "x-powers,axp809"
- * "x-powers,axp813"
-- reg: The I2C slave address or RSB hardware address for the AXP chip
-- interrupt-controller: The PMIC has its own internal IRQs
-- #interrupt-cells: Should be set to 1
-
-Supported common regulator properties, see ../regulator/regulator.txt for
-more information:
-- regulator-ramp-delay: sets the ramp up delay in uV/us
- AXP20x/DCDC2: 1600, 800
- AXP20x/LDO3: 1600, 800
-- regulator-soft-start: enable the output at the lowest possible voltage and
- only then set the desired voltage
- AXP20x/LDO3: software-based implementation
-
-Optional properties:
-- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
-- x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz
- AXP152/20X: range: 750-1875, Default: 1.5 MHz
- AXP22X/8XX: range: 1800-4050, Default: 3 MHz
-
-- x-powers,drive-vbus-en: boolean, set this when the N_VBUSEN pin is
- used as an output pin to control an external
- regulator to drive the OTG VBus, rather then
- as an input pin which signals whether the
- board is driving OTG VBus or not.
- (axp221 / axp223 / axp803/ axp813 only)
-
-- x-powers,self-working-mode and
- x-powers,master-mode: Boolean (axp806 only). Set either of these when the
- PMIC is wired for self-working mode or master mode.
- If neither is set then slave mode is assumed.
- This corresponds to how the MODESET pin is wired.
-
-- <input>-supply: a phandle to the regulator supply node. May be omitted if
- inputs are unregulated, such as using the IPSOUT output
- from the PMIC.
-
-- regulators: A node that houses a sub-node for each regulator. Regulators
- not used but preferred to be managed by the OS should be
- listed as well.
- See Documentation/devicetree/bindings/regulator/regulator.txt
- for more information on standard regulator bindings.
-
-Optional properties for DCDC regulators:
-- x-powers,dcdc-workmode: 1 for PWM mode, 0 for AUTO (PWM/PFM) mode
- Default: Current hardware setting
- The DCDC regulators work in a mixed PWM/PFM mode,
- using PFM under light loads and switching to PWM
- for heavier loads. Forcing PWM mode trades efficiency
- under light loads for lower output noise. This
- probably makes sense for HiFi audio related
- applications that aren't battery constrained.
-
-AXP202/AXP209 regulators, type, and corresponding input supply names:
-
-Regulator Type Supply Name Notes
---------- ---- ----------- -----
-DCDC2 : DC-DC buck : vin2-supply
-DCDC3 : DC-DC buck : vin3-supply
-LDO1 : LDO : acin-supply : always on
-LDO2 : LDO : ldo24in-supply : shared supply
-LDO3 : LDO : ldo3in-supply
-LDO4 : LDO : ldo24in-supply : shared supply
-LDO5 : LDO : ldo5in-supply
-
-AXP221/AXP223 regulators, type, and corresponding input supply names:
-
-Regulator Type Supply Name Notes
---------- ---- ----------- -----
-DCDC1 : DC-DC buck : vin1-supply
-DCDC2 : DC-DC buck : vin2-supply
-DCDC3 : DC-DC buck : vin3-supply
-DCDC4 : DC-DC buck : vin4-supply
-DCDC5 : DC-DC buck : vin5-supply
-DC1SW : On/Off Switch : : DCDC1 secondary output
-DC5LDO : LDO : : input from DCDC5
-ALDO1 : LDO : aldoin-supply : shared supply
-ALDO2 : LDO : aldoin-supply : shared supply
-ALDO3 : LDO : aldoin-supply : shared supply
-DLDO1 : LDO : dldoin-supply : shared supply
-DLDO2 : LDO : dldoin-supply : shared supply
-DLDO3 : LDO : dldoin-supply : shared supply
-DLDO4 : LDO : dldoin-supply : shared supply
-ELDO1 : LDO : eldoin-supply : shared supply
-ELDO2 : LDO : eldoin-supply : shared supply
-ELDO3 : LDO : eldoin-supply : shared supply
-LDO_IO0 : LDO : ips-supply : GPIO 0
-LDO_IO1 : LDO : ips-supply : GPIO 1
-RTC_LDO : LDO : ips-supply : always on
-DRIVEVBUS : Enable output : drivevbus-supply : external regulator
-
-AXP803 regulators, type, and corresponding input supply names:
-
-Regulator Type Supply Name Notes
---------- ---- ----------- -----
-DCDC1 : DC-DC buck : vin1-supply
-DCDC2 : DC-DC buck : vin2-supply : poly-phase capable
-DCDC3 : DC-DC buck : vin3-supply : poly-phase capable
-DCDC4 : DC-DC buck : vin4-supply
-DCDC5 : DC-DC buck : vin5-supply : poly-phase capable
-DCDC6 : DC-DC buck : vin6-supply : poly-phase capable
-DC1SW : On/Off Switch : : DCDC1 secondary output
-ALDO1 : LDO : aldoin-supply : shared supply
-ALDO2 : LDO : aldoin-supply : shared supply
-ALDO3 : LDO : aldoin-supply : shared supply
-DLDO1 : LDO : dldoin-supply : shared supply
-DLDO2 : LDO : dldoin-supply : shared supply
-DLDO3 : LDO : dldoin-supply : shared supply
-DLDO4 : LDO : dldoin-supply : shared supply
-ELDO1 : LDO : eldoin-supply : shared supply
-ELDO2 : LDO : eldoin-supply : shared supply
-ELDO3 : LDO : eldoin-supply : shared supply
-FLDO1 : LDO : fldoin-supply : shared supply
-FLDO2 : LDO : fldoin-supply : shared supply
-LDO_IO0 : LDO : ips-supply : GPIO 0
-LDO_IO1 : LDO : ips-supply : GPIO 1
-RTC_LDO : LDO : ips-supply : always on
-DRIVEVBUS : Enable output : drivevbus-supply : external regulator
-
-AXP806 regulators, type, and corresponding input supply names:
-
-Regulator Type Supply Name Notes
---------- ---- ----------- -----
-DCDCA : DC-DC buck : vina-supply : poly-phase capable
-DCDCB : DC-DC buck : vinb-supply : poly-phase capable
-DCDCC : DC-DC buck : vinc-supply : poly-phase capable
-DCDCD : DC-DC buck : vind-supply : poly-phase capable
-DCDCE : DC-DC buck : vine-supply : poly-phase capable
-ALDO1 : LDO : aldoin-supply : shared supply
-ALDO2 : LDO : aldoin-supply : shared supply
-ALDO3 : LDO : aldoin-supply : shared supply
-BLDO1 : LDO : bldoin-supply : shared supply
-BLDO2 : LDO : bldoin-supply : shared supply
-BLDO3 : LDO : bldoin-supply : shared supply
-BLDO4 : LDO : bldoin-supply : shared supply
-CLDO1 : LDO : cldoin-supply : shared supply
-CLDO2 : LDO : cldoin-supply : shared supply
-CLDO3 : LDO : cldoin-supply : shared supply
-SW : On/Off Switch : swin-supply
-
-Additionally, the AXP806 DC-DC regulators support poly-phase arrangements
-for higher output current. The possible groupings are: A+B, A+B+C, D+E.
-
-AXP809 regulators, type, and corresponding input supply names:
-
-Regulator Type Supply Name Notes
---------- ---- ----------- -----
-DCDC1 : DC-DC buck : vin1-supply
-DCDC2 : DC-DC buck : vin2-supply
-DCDC3 : DC-DC buck : vin3-supply
-DCDC4 : DC-DC buck : vin4-supply
-DCDC5 : DC-DC buck : vin5-supply
-DC1SW : On/Off Switch : : DCDC1 secondary output
-DC5LDO : LDO : : input from DCDC5
-ALDO1 : LDO : aldoin-supply : shared supply
-ALDO2 : LDO : aldoin-supply : shared supply
-ALDO3 : LDO : aldoin-supply : shared supply
-DLDO1 : LDO : dldoin-supply : shared supply
-DLDO2 : LDO : dldoin-supply : shared supply
-ELDO1 : LDO : eldoin-supply : shared supply
-ELDO2 : LDO : eldoin-supply : shared supply
-ELDO3 : LDO : eldoin-supply : shared supply
-LDO_IO0 : LDO : ips-supply : GPIO 0
-LDO_IO1 : LDO : ips-supply : GPIO 1
-RTC_LDO : LDO : ips-supply : always on
-SW : On/Off Switch : swin-supply
-
-AXP813 regulators, type, and corresponding input supply names:
-
-Regulator Type Supply Name Notes
---------- ---- ----------- -----
-DCDC1 : DC-DC buck : vin1-supply
-DCDC2 : DC-DC buck : vin2-supply : poly-phase capable
-DCDC3 : DC-DC buck : vin3-supply : poly-phase capable
-DCDC4 : DC-DC buck : vin4-supply
-DCDC5 : DC-DC buck : vin5-supply : poly-phase capable
-DCDC6 : DC-DC buck : vin6-supply : poly-phase capable
-DCDC7 : DC-DC buck : vin7-supply
-ALDO1 : LDO : aldoin-supply : shared supply
-ALDO2 : LDO : aldoin-supply : shared supply
-ALDO3 : LDO : aldoin-supply : shared supply
-DLDO1 : LDO : dldoin-supply : shared supply
-DLDO2 : LDO : dldoin-supply : shared supply
-DLDO3 : LDO : dldoin-supply : shared supply
-DLDO4 : LDO : dldoin-supply : shared supply
-ELDO1 : LDO : eldoin-supply : shared supply
-ELDO2 : LDO : eldoin-supply : shared supply
-ELDO3 : LDO : eldoin-supply : shared supply
-FLDO1 : LDO : fldoin-supply : shared supply
-FLDO2 : LDO : fldoin-supply : shared supply
-FLDO3 : LDO : fldoin-supply : shared supply
-LDO_IO0 : LDO : ips-supply : GPIO 0
-LDO_IO1 : LDO : ips-supply : GPIO 1
-RTC_LDO : LDO : ips-supply : always on
-SW : On/Off Switch : swin-supply
-DRIVEVBUS : Enable output : drivevbus-supply : external regulator
-
-Example:
-
-axp209: pmic@34 {
- compatible = "x-powers,axp209";
- reg = <0x34>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <1>;
-
- regulators {
- x-powers,dcdc-freq = <1500>;
-
- vdd_cpu: dcdc2 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1450000>;
- regulator-name = "vdd-cpu";
- };
-
- vdd_int_dll: dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-int-dll";
- };
-
- vdd_rtc: ldo1 {
- regulator-always-on;
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1400000>;
- regulator-name = "vdd-rtc";
- };
-
- avcc: ldo2 {
- regulator-always-on;
- regulator-min-microvolt = <2700000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "avcc";
- };
-
- ldo3 {
- /* unused but preferred to be managed by OS */
- };
- };
-};
new file mode 100644
@@ -0,0 +1,400 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/x-powers,axp152.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: X-Powers AXP PMIC Device Tree Bindings
+
+maintainers:
+ - Chen-Yu Tsai <wens@csie.org>
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - x-powers,axp152
+ - x-powers,axp202
+ - x-powers,axp209
+
+ then:
+ properties:
+ regulators:
+ properties:
+ x-powers,dcdc-freq:
+ minimum: 750
+ maximum: 1875
+ default: 1500
+
+ else:
+ properties:
+ regulators:
+ properties:
+ x-powers,dcdc-freq:
+ minimum: 1800
+ maximum: 4050
+ default: 3000
+
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - x-powers,axp152
+ - x-powers,axp202
+ - x-powers,axp209
+
+ then:
+ not:
+ required:
+ - x-powers,drive-vbus-en
+
+ - if:
+ not:
+ properties:
+ compatible:
+ contains:
+ const: x-powers,axp806
+
+ then:
+ allOf:
+ - not:
+ required:
+ - x-powers,self-working-mode
+
+ - not:
+ required:
+ - x-powers,master-mode
+
+ - if:
+ not:
+ properties:
+ compatible:
+ contains:
+ const: x-powers,axp305
+
+ then:
+ required:
+ - interrupts
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - x-powers,axp152
+ - x-powers,axp202
+ - x-powers,axp209
+ - x-powers,axp221
+ - x-powers,axp223
+ - x-powers,axp803
+ - x-powers,axp806
+ - x-powers,axp809
+ - x-powers,axp813
+ - items:
+ - const: x-powers,axp805
+ - const: x-powers,axp806
+ - items:
+ - const: x-powers,axp305
+ - const: x-powers,axp805
+ - const: x-powers,axp806
+ - items:
+ - const: x-powers,axp818
+ - const: x-powers,axp813
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ "#interrupt-cells":
+ const: 1
+
+ x-powers,drive-vbus-en:
+ type: boolean
+ description: >
+ Set this when the N_VBUSEN pin is used as an output pin to control an
+ external regulator to drive the OTG VBus, rather then as an input pin
+ which signals whether the board is driving OTG VBus or not.
+
+ x-powers,self-working-mode:
+ type: boolean
+ description: >
+ Set this when the PMIC is wired for self-working mode through the MODESET
+ pin.
+
+ x-powers,master-mode:
+ type: boolean
+ description: >
+ Set this when the PMIC is wired for master mode through the MODESET pin.
+
+ vin1-supply:
+ description: >
+ DCDC1 power supply node, if present.
+
+ vin2-supply:
+ description: >
+ DCDC2 power supply node, if present.
+
+ vin3-supply:
+ description: >
+ DCDC3 power supply node, if present.
+
+ vin4-supply:
+ description: >
+ DCDC4 power supply node, if present.
+
+ vin5-supply:
+ description: >
+ DCDC5 power supply node, if present.
+
+ vin6-supply:
+ description: >
+ DCDC6 power supply node, if present.
+
+ vin7-supply:
+ description: >
+ DCDC7 power supply node, if present.
+
+ vina-supply:
+ description: >
+ DCDCA power supply node, if present.
+
+ vinb-supply:
+ description: >
+ DCDCB power supply node, if present.
+
+ vinc-supply:
+ description: >
+ DCDCC power supply node, if present.
+
+ vind-supply:
+ description: >
+ DCDCD power supply node, if present.
+
+ vine-supply:
+ description: >
+ DCDCE power supply node, if present.
+
+ acin-supply:
+ description: >
+ LDO1 power supply node, if present.
+
+ ldo24in-supply:
+ description: >
+ LDO2 and LDO4 power supply node, if present.
+
+ ldo3in-supply:
+ description: >
+ LDO3 power supply node, if present.
+
+ ldo5in-supply:
+ description: >
+ LDO5 power supply node, if present.
+
+ aldoin-supply:
+ description: >
+ ALDO* power supply node, if present.
+
+ bldoin-supply:
+ description: >
+ BLDO* power supply node, if present.
+
+ cldoin-supply:
+ description: >
+ CLDO* power supply node, if present.
+
+ dldoin-supply:
+ description: >
+ DLDO* power supply node, if present.
+
+ eldoin-supply:
+ description: >
+ ELDO* power supply node, if present.
+
+ fldoin-supply:
+ description: >
+ FLDO* power supply node, if present.
+
+ ips-supply:
+ description: >
+ LDO_IO0, LDO_IO1 and RTC_LDO power supply node, if present.
+
+ drivevbus-supply:
+ description: >
+ DRIVEVBUS power supply node, if present.
+
+ swin-supply:
+ description: >
+ SW power supply node, if present.
+
+ adc:
+ $ref: /schemas/iio/adc/x-powers,axp209-adc.yaml#
+
+ gpio:
+ $ref: /schemas/gpio/x-powers,axp209-gpio.yaml#
+
+ ac-power:
+ $ref: /schemas/power/supply/x-powers,axp20x-ac-power-supply.yaml#
+
+ battery-power:
+ $ref: /schemas/power/supply/x-powers,axp20x-battery-power-supply.yaml#
+
+ usb-power:
+ $ref: /schemas/power/supply/x-powers,axp20x-usb-power-supply.yaml#
+
+ regulators:
+ type: object
+
+ properties:
+ x-powers,dcdc-freq:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: >
+ Defines the work frequency of DC-DC in kHz.
+
+ patternProperties:
+ "^(([a-f])?ldo[0-9]|dcdc[0-7a-e]|ldo(_|-)io(0|1)|(dc1)?sw|rtc(_|-)ldo|drivevbus|dc5ldo)$":
+ $ref: /schemas/regulator/regulator.yaml#
+ type: object
+
+ properties:
+ regulator-ramp-delay:
+ description: >
+ Only 800 and 1600 are valid for the DCDC2 and LDO3 regulators on
+ the AXP209.
+
+ regulator-soft-start:
+ description: >
+ Only valid for the LDO3 regulator.
+
+ x-powers,dcdc-workmode:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1]
+ description: >
+ Only valid for DCDC regulators. Setup 1 for PWM mode, 0
+ for AUTO (PWM/PFM) mode. The DCDC regulators work in a
+ mixed PWM/PFM mode, using PFM under light loads and
+ switching to PWM for heavier loads. Forcing PWM mode
+ trades efficiency under light loads for lower output
+ noise. This probably makes sense for HiFi audio related
+ applications that aren't battery constrained.
+
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - "#interrupt-cells"
+ - interrupt-controller
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@30 {
+ compatible = "x-powers,axp152";
+ reg = <0x30>;
+ interrupts = <0>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ ac_power_supply: ac-power {
+ compatible = "x-powers,axp202-ac-power-supply";
+ };
+
+ axp_adc: adc {
+ compatible = "x-powers,axp209-adc";
+ #io-channel-cells = <1>;
+ };
+
+ axp_gpio: gpio {
+ compatible = "x-powers,axp209-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ gpio0-adc-pin {
+ pins = "GPIO0";
+ function = "adc";
+ };
+ };
+
+ battery_power_supply: battery-power {
+ compatible = "x-powers,axp209-battery-power-supply";
+ };
+
+ regulators {
+ /* Default work frequency for buck regulators */
+ x-powers,dcdc-freq = <1500>;
+
+ reg_dcdc2: dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-dll";
+ };
+
+ reg_ldo1: ldo1 {
+ /* LDO1 is a fixed output regulator */
+ regulator-always-on;
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-rtc";
+ };
+
+ reg_ldo2: ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+ };
+
+ reg_ldo3: ldo3 {
+ regulator-name = "ldo3";
+ };
+
+ reg_ldo4: ldo4 {
+ regulator-name = "ldo4";
+ };
+
+ reg_ldo5: ldo5 {
+ regulator-name = "ldo5";
+ };
+ };
+
+ usb_power_supply: usb-power {
+ compatible = "x-powers,axp202-usb-power-supply";
+ };
+ };
+ };
The X-Powers AXP PMICs are supported by Linux thanks to its device tree binding. Now that we have the DT validation in place, let's convert the device tree bindings for that driver over to a YAML schema. Cc: Chen-Yu Tsai <wens@csie.org> Cc: Lee Jones <lee.jones@linaro.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> --- Changes from v1: - Add GPIO example - Remove the limitation on regulator-ramp-delay --- .../i2c/allwinner,sun6i-a31-p2wi.yaml | 2 +- .../devicetree/bindings/mfd/axp20x.txt | 273 ------------ .../bindings/mfd/x-powers,axp152.yaml | 400 ++++++++++++++++++ 3 files changed, 401 insertions(+), 274 deletions(-) delete mode 100644 Documentation/devicetree/bindings/mfd/axp20x.txt create mode 100644 Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml