| Message ID | 20211107075646.4366-5-chunfeng.yun@mediatek.com |
|---|---|
| State | Changes Requested |
| Headers | show |
| Series | [1/6] dt-bindings: nvmem: mediatek: add support bits property | expand |
On 07-11-21, 15:56, Chunfeng Yun wrote: > Due to some SoCs have a bit shift issue that will drop a bit for usb3 > phy or pcie phy, fix it by adding software efuse reading and setting, > but only support it optionally for versoin 2/3. s/versoin/version > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > --- > drivers/phy/mediatek/phy-mtk-tphy.c | 162 ++++++++++++++++++++++++++++ > 1 file changed, 162 insertions(+) > > diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c > index cdcef865fe9e..3b5b1c266595 100644 > --- a/drivers/phy/mediatek/phy-mtk-tphy.c > +++ b/drivers/phy/mediatek/phy-mtk-tphy.c > @@ -12,6 +12,7 @@ > #include <linux/iopoll.h> > #include <linux/mfd/syscon.h> > #include <linux/module.h> > +#include <linux/nvmem-consumer.h> > #include <linux/of_address.h> > #include <linux/of_device.h> > #include <linux/phy/phy.h> > @@ -41,6 +42,9 @@ > #define SSUSB_SIFSLV_V2_U3PHYD 0x200 > #define SSUSB_SIFSLV_V2_U3PHYA 0x400 > > +#define U3P_MISC_REG1 0x04 > +#define MR1_EFUSE_AUTO_LOAD_DIS BIT(6) > + > #define U3P_USBPHYACR0 0x000 > #define PA0_RG_U2PLL_FORCE_ON BIT(15) > #define PA0_USB20_PLL_PREDIV GENMASK(7, 6) > @@ -133,6 +137,8 @@ > #define P3C_RG_SWRST_U3_PHYD_FORCE_EN BIT(24) > > #define U3P_U3_PHYA_REG0 0x000 > +#define P3A_RG_IEXT_INTR GENMASK(15, 10) > +#define P3A_RG_IEXT_INTR_VAL(x) ((0x3f & (x)) << 10) > #define P3A_RG_CLKDRV_OFF GENMASK(3, 2) > #define P3A_RG_CLKDRV_OFF_VAL(x) ((0x3 & (x)) << 2) > > @@ -187,6 +193,19 @@ > #define P3D_RG_FWAKE_TH GENMASK(21, 16) > #define P3D_RG_FWAKE_TH_VAL(x) ((0x3f & (x)) << 16) > > +#define U3P_U3_PHYD_IMPCAL0 0x010 > +#define P3D_RG_FORCE_TX_IMPEL BIT(31) > +#define P3D_RG_TX_IMPEL GENMASK(28, 24) > +#define P3D_RG_TX_IMPEL_VAL(x) ((0x1f & (x)) << 24) > + > +#define U3P_U3_PHYD_IMPCAL1 0x014 > +#define P3D_RG_FORCE_RX_IMPEL BIT(31) > +#define P3D_RG_RX_IMPEL GENMASK(28, 24) > +#define P3D_RG_RX_IMPEL_VAL(x) ((0x1f & (x)) << 24) > + > +#define U3P_U3_PHYD_RSV 0x054 > +#define P3D_RG_EFUSE_AUTO_LOAD_DIS BIT(12) > + > #define U3P_U3_PHYD_CDR1 0x05c > #define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24) > #define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24) > @@ -307,6 +326,11 @@ struct mtk_phy_pdata { > * 48M PLL, fix it by switching PLL to 26M from default 48M > */ > bool sw_pll_48m_to_26m; > + /* > + * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse, > + * support sw way, also support it for v2/v3 optionally. > + */ > + bool sw_efuse_supported; > enum mtk_phy_version version; > }; > > @@ -336,6 +360,10 @@ struct mtk_phy_instance { > struct regmap *type_sw; > u32 type_sw_reg; > u32 type_sw_index; > + u32 efuse_sw_en; > + u32 efuse_intr; > + u32 efuse_tx_imp; > + u32 efuse_rx_imp; > int eye_src; > int eye_vrt; > int eye_term; > @@ -1040,6 +1068,130 @@ static int phy_type_set(struct mtk_phy_instance *instance) > return 0; > } > > +static int phy_efuse_get(struct mtk_tphy *tphy, struct mtk_phy_instance *instance) > +{ > + struct device *dev = &instance->phy->dev; > + int ret = 0; > + > + /* tphy v1 doesn't support sw efuse, skip it */ > + if (!tphy->pdata->sw_efuse_supported) { > + instance->efuse_sw_en = 0; > + return 0; > + } > + > + /* software efuse is optional */ > + instance->efuse_sw_en = device_property_read_bool(dev, "nvmem-cells"); > + if (!instance->efuse_sw_en) > + return 0; > + > + switch (instance->type) { > + case PHY_TYPE_USB2: > + ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr); > + if (ret) { > + dev_err(dev, "fail to get u2 intr efuse, %d\n", ret); > + break; > + } > + > + /* no efuse, ignore it */ > + if (!instance->efuse_intr) { > + dev_warn(dev, "no u2 intr efuse, but dts enable it\n"); > + instance->efuse_sw_en = 0; > + break; > + } What does this check do...? so a zero value is not valid..? > + > + dev_info(dev, "u2 efuse - intr %x\n", instance->efuse_intr); dev_dbg()? > + break; empty line after break improves readability, pls add > + case PHY_TYPE_USB3: > + case PHY_TYPE_PCIE: > + ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr); > + if (ret) { > + dev_err(dev, "fail to get u3 intr efuse, %d\n", ret); > + break; > + } This seems to be common, why not read this before switch? > + > + ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", &instance->efuse_rx_imp); > + if (ret) { > + dev_err(dev, "fail to get u3 rx_imp efuse, %d\n", ret); > + break; > + } > + > + ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", &instance->efuse_tx_imp); > + if (ret) { > + dev_err(dev, "fail to get u3 tx_imp efuse, %d\n", ret); > + break; > + } > + > + /* no efuse, ignore it */ > + if (!instance->efuse_intr && > + !instance->efuse_rx_imp && > + !instance->efuse_rx_imp) { > + dev_warn(dev, "no u3 intr efuse, but dts enable it\n"); > + instance->efuse_sw_en = 0; > + break; > + } again, zero values are not valid? > + > + dev_info(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n", > + instance->efuse_intr, instance->efuse_rx_imp, > + instance->efuse_tx_imp); dbg pls > + break; > + default: > + dev_err(dev, "no sw efuse for type %d\n", instance->type); > + ret = -EINVAL; > + } > + > + return ret; > +} > + > +static void phy_efuse_set(struct mtk_phy_instance *instance) > +{ > + struct device *dev = &instance->phy->dev; > + struct u2phy_banks *u2_banks = &instance->u2_banks; > + struct u3phy_banks *u3_banks = &instance->u3_banks; > + u32 tmp; > + > + if (!instance->efuse_sw_en) > + return; > + > + switch (instance->type) { > + case PHY_TYPE_USB2: > + tmp = readl(u2_banks->misc + U3P_MISC_REG1); > + tmp |= MR1_EFUSE_AUTO_LOAD_DIS; > + writel(tmp, u2_banks->misc + U3P_MISC_REG1); > + > + tmp = readl(u2_banks->com + U3P_USBPHYACR1); > + tmp &= ~PA1_RG_INTR_CAL; > + tmp |= PA1_RG_INTR_CAL_VAL(instance->efuse_intr); > + writel(tmp, u2_banks->com + U3P_USBPHYACR1); > + break; > + case PHY_TYPE_USB3: > + case PHY_TYPE_PCIE: > + tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); > + tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; > + writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV); add a updatel() macro and use this here and other places?
On Mon, 2021-11-22 at 17:05 +0530, Vinod Koul wrote: > On 07-11-21, 15:56, Chunfeng Yun wrote: > > Due to some SoCs have a bit shift issue that will drop a bit for > > usb3 > > phy or pcie phy, fix it by adding software efuse reading and > > setting, > > but only support it optionally for versoin 2/3. > > s/versoin/version Ok > > > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > > --- > > drivers/phy/mediatek/phy-mtk-tphy.c | 162 > > ++++++++++++++++++++++++++++ > > 1 file changed, 162 insertions(+) > > > > diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c > > b/drivers/phy/mediatek/phy-mtk-tphy.c > > index cdcef865fe9e..3b5b1c266595 100644 > > --- a/drivers/phy/mediatek/phy-mtk-tphy.c > > +++ b/drivers/phy/mediatek/phy-mtk-tphy.c > > @@ -12,6 +12,7 @@ > > #include <linux/iopoll.h> > > #include <linux/mfd/syscon.h> > > #include <linux/module.h> > > +#include <linux/nvmem-consumer.h> > > #include <linux/of_address.h> > > #include <linux/of_device.h> > > #include <linux/phy/phy.h> > > @@ -41,6 +42,9 @@ > > #define SSUSB_SIFSLV_V2_U3PHYD 0x200 > > #define SSUSB_SIFSLV_V2_U3PHYA 0x400 > > > > +#define U3P_MISC_REG1 0x04 > > +#define MR1_EFUSE_AUTO_LOAD_DIS BIT(6) > > + > > #define U3P_USBPHYACR0 0x000 > > #define PA0_RG_U2PLL_FORCE_ON BIT(15) > > #define PA0_USB20_PLL_PREDIV GENMASK(7, 6) > > @@ -133,6 +137,8 @@ > > #define P3C_RG_SWRST_U3_PHYD_FORCE_EN BIT(24) > > > > #define U3P_U3_PHYA_REG0 0x000 > > +#define P3A_RG_IEXT_INTR GENMASK(15, 10) > > +#define P3A_RG_IEXT_INTR_VAL(x) ((0x3f & (x)) << 10) > > #define P3A_RG_CLKDRV_OFF GENMASK(3, 2) > > #define P3A_RG_CLKDRV_OFF_VAL(x) ((0x3 & (x)) << 2) > > > > @@ -187,6 +193,19 @@ > > #define P3D_RG_FWAKE_TH GENMASK(21, 16) > > #define P3D_RG_FWAKE_TH_VAL(x) ((0x3f & (x)) << 16) > > > > +#define U3P_U3_PHYD_IMPCAL0 0x010 > > +#define P3D_RG_FORCE_TX_IMPEL BIT(31) > > +#define P3D_RG_TX_IMPEL GENMASK(28, 24) > > +#define P3D_RG_TX_IMPEL_VAL(x) ((0x1f & (x)) << 24) > > + > > +#define U3P_U3_PHYD_IMPCAL1 0x014 > > +#define P3D_RG_FORCE_RX_IMPEL BIT(31) > > +#define P3D_RG_RX_IMPEL GENMASK(28, 24) > > +#define P3D_RG_RX_IMPEL_VAL(x) ((0x1f & (x)) << 24) > > + > > +#define U3P_U3_PHYD_RSV 0x054 > > +#define P3D_RG_EFUSE_AUTO_LOAD_DIS BIT(12) > > + > > #define U3P_U3_PHYD_CDR1 0x05c > > #define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24) > > #define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24) > > @@ -307,6 +326,11 @@ struct mtk_phy_pdata { > > * 48M PLL, fix it by switching PLL to 26M from default 48M > > */ > > bool sw_pll_48m_to_26m; > > + /* > > + * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse, > > + * support sw way, also support it for v2/v3 optionally. > > + */ > > + bool sw_efuse_supported; > > enum mtk_phy_version version; > > }; > > > > @@ -336,6 +360,10 @@ struct mtk_phy_instance { > > struct regmap *type_sw; > > u32 type_sw_reg; > > u32 type_sw_index; > > + u32 efuse_sw_en; > > + u32 efuse_intr; > > + u32 efuse_tx_imp; > > + u32 efuse_rx_imp; > > int eye_src; > > int eye_vrt; > > int eye_term; > > @@ -1040,6 +1068,130 @@ static int phy_type_set(struct > > mtk_phy_instance *instance) > > return 0; > > } > > > > +static int phy_efuse_get(struct mtk_tphy *tphy, struct > > mtk_phy_instance *instance) > > +{ > > + struct device *dev = &instance->phy->dev; > > + int ret = 0; > > + > > + /* tphy v1 doesn't support sw efuse, skip it */ > > + if (!tphy->pdata->sw_efuse_supported) { > > + instance->efuse_sw_en = 0; > > + return 0; > > + } > > + > > + /* software efuse is optional */ > > + instance->efuse_sw_en = device_property_read_bool(dev, "nvmem- > > cells"); > > + if (!instance->efuse_sw_en) > > + return 0; > > + > > + switch (instance->type) { > > + case PHY_TYPE_USB2: > > + ret = nvmem_cell_read_variable_le_u32(dev, "intr", > > &instance->efuse_intr); > > + if (ret) { > > + dev_err(dev, "fail to get u2 intr efuse, %d\n", > > ret); > > + break; > > + } > > + > > + /* no efuse, ignore it */ > > + if (!instance->efuse_intr) { > > + dev_warn(dev, "no u2 intr efuse, but dts enable > > it\n"); > > + instance->efuse_sw_en = 0; > > + break; > > + } > > What does this check do...? so a zero value is not valid..? Yes, because it's also zero for SoC without efuse, prefer to use default value instead. > > > + > > + dev_info(dev, "u2 efuse - intr %x\n", instance- > > >efuse_intr); > > dev_dbg()? We usually use HW auto load way, print this log can help to point out that it's specific SoC. > > > + break; > > empty line after break improves readability, pls add Ok > > > + case PHY_TYPE_USB3: > > + case PHY_TYPE_PCIE: > > + ret = nvmem_cell_read_variable_le_u32(dev, "intr", > > &instance->efuse_intr); > > + if (ret) { > > + dev_err(dev, "fail to get u3 intr efuse, %d\n", > > ret); > > + break; > > + } > > This seems to be common, why not read this before switch? It's not used for SGMII or SATA, but not applied until now > > > + > > + ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", > > &instance->efuse_rx_imp); > > + if (ret) { > > + dev_err(dev, "fail to get u3 rx_imp efuse, > > %d\n", ret); > > + break; > > + } > > + > > + ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", > > &instance->efuse_tx_imp); > > + if (ret) { > > + dev_err(dev, "fail to get u3 tx_imp efuse, > > %d\n", ret); > > + break; > > + } > > + > > + /* no efuse, ignore it */ > > + if (!instance->efuse_intr && > > + !instance->efuse_rx_imp && > > + !instance->efuse_rx_imp) { > > + dev_warn(dev, "no u3 intr efuse, but dts enable > > it\n"); > > + instance->efuse_sw_en = 0; > > + break; > > + } > > again, zero values are not valid? It's also zero for SoC without efuse, treat it as invalid value > > > + > > + dev_info(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp > > %x\n", > > + instance->efuse_intr, instance->efuse_rx_imp, > > + instance->efuse_tx_imp); > > dbg pls Ok > > > + break; > > + default: > > + dev_err(dev, "no sw efuse for type %d\n", instance- > > >type); > > + ret = -EINVAL; > > + } > > + > > + return ret; > > +} > > + > > +static void phy_efuse_set(struct mtk_phy_instance *instance) > > +{ > > + struct device *dev = &instance->phy->dev; > > + struct u2phy_banks *u2_banks = &instance->u2_banks; > > + struct u3phy_banks *u3_banks = &instance->u3_banks; > > + u32 tmp; > > + > > + if (!instance->efuse_sw_en) > > + return; > > + > > + switch (instance->type) { > > + case PHY_TYPE_USB2: > > + tmp = readl(u2_banks->misc + U3P_MISC_REG1); > > + tmp |= MR1_EFUSE_AUTO_LOAD_DIS; > > + writel(tmp, u2_banks->misc + U3P_MISC_REG1); > > + > > + tmp = readl(u2_banks->com + U3P_USBPHYACR1); > > + tmp &= ~PA1_RG_INTR_CAL; > > + tmp |= PA1_RG_INTR_CAL_VAL(instance->efuse_intr); > > + writel(tmp, u2_banks->com + U3P_USBPHYACR1); > > + break; > > + case PHY_TYPE_USB3: > > + case PHY_TYPE_PCIE: > > + tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); > > + tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; > > + writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV); > > add a updatel() macro and use this here and other places? You mean add macro to set/clear bits? If so, I need prepare another patch for this purpose Thanks a lot >
On 24-11-21, 14:54, Chunfeng Yun wrote: > On Mon, 2021-11-22 at 17:05 +0530, Vinod Koul wrote: > > On 07-11-21, 15:56, Chunfeng Yun wrote: > > > Due to some SoCs have a bit shift issue that will drop a bit for > > > usb3 > > > phy or pcie phy, fix it by adding software efuse reading and > > > setting, > > > but only support it optionally for versoin 2/3. > > > > s/versoin/version > Ok > > > > > > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > > > --- > > > drivers/phy/mediatek/phy-mtk-tphy.c | 162 > > > ++++++++++++++++++++++++++++ > > > 1 file changed, 162 insertions(+) > > > > > > diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c > > > b/drivers/phy/mediatek/phy-mtk-tphy.c > > > index cdcef865fe9e..3b5b1c266595 100644 > > > --- a/drivers/phy/mediatek/phy-mtk-tphy.c > > > +++ b/drivers/phy/mediatek/phy-mtk-tphy.c > > > @@ -12,6 +12,7 @@ > > > #include <linux/iopoll.h> > > > #include <linux/mfd/syscon.h> > > > #include <linux/module.h> > > > +#include <linux/nvmem-consumer.h> > > > #include <linux/of_address.h> > > > #include <linux/of_device.h> > > > #include <linux/phy/phy.h> > > > @@ -41,6 +42,9 @@ > > > #define SSUSB_SIFSLV_V2_U3PHYD 0x200 > > > #define SSUSB_SIFSLV_V2_U3PHYA 0x400 > > > > > > +#define U3P_MISC_REG1 0x04 > > > +#define MR1_EFUSE_AUTO_LOAD_DIS BIT(6) > > > + > > > #define U3P_USBPHYACR0 0x000 > > > #define PA0_RG_U2PLL_FORCE_ON BIT(15) > > > #define PA0_USB20_PLL_PREDIV GENMASK(7, 6) > > > @@ -133,6 +137,8 @@ > > > #define P3C_RG_SWRST_U3_PHYD_FORCE_EN BIT(24) > > > > > > #define U3P_U3_PHYA_REG0 0x000 > > > +#define P3A_RG_IEXT_INTR GENMASK(15, 10) > > > +#define P3A_RG_IEXT_INTR_VAL(x) ((0x3f & (x)) << 10) > > > #define P3A_RG_CLKDRV_OFF GENMASK(3, 2) > > > #define P3A_RG_CLKDRV_OFF_VAL(x) ((0x3 & (x)) << 2) > > > > > > @@ -187,6 +193,19 @@ > > > #define P3D_RG_FWAKE_TH GENMASK(21, 16) > > > #define P3D_RG_FWAKE_TH_VAL(x) ((0x3f & (x)) << 16) > > > > > > +#define U3P_U3_PHYD_IMPCAL0 0x010 > > > +#define P3D_RG_FORCE_TX_IMPEL BIT(31) > > > +#define P3D_RG_TX_IMPEL GENMASK(28, 24) > > > +#define P3D_RG_TX_IMPEL_VAL(x) ((0x1f & (x)) << 24) > > > + > > > +#define U3P_U3_PHYD_IMPCAL1 0x014 > > > +#define P3D_RG_FORCE_RX_IMPEL BIT(31) > > > +#define P3D_RG_RX_IMPEL GENMASK(28, 24) > > > +#define P3D_RG_RX_IMPEL_VAL(x) ((0x1f & (x)) << 24) > > > + > > > +#define U3P_U3_PHYD_RSV 0x054 > > > +#define P3D_RG_EFUSE_AUTO_LOAD_DIS BIT(12) > > > + > > > #define U3P_U3_PHYD_CDR1 0x05c > > > #define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24) > > > #define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24) > > > @@ -307,6 +326,11 @@ struct mtk_phy_pdata { > > > * 48M PLL, fix it by switching PLL to 26M from default 48M > > > */ > > > bool sw_pll_48m_to_26m; > > > + /* > > > + * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse, > > > + * support sw way, also support it for v2/v3 optionally. > > > + */ > > > + bool sw_efuse_supported; > > > enum mtk_phy_version version; > > > }; > > > > > > @@ -336,6 +360,10 @@ struct mtk_phy_instance { > > > struct regmap *type_sw; > > > u32 type_sw_reg; > > > u32 type_sw_index; > > > + u32 efuse_sw_en; > > > + u32 efuse_intr; > > > + u32 efuse_tx_imp; > > > + u32 efuse_rx_imp; > > > int eye_src; > > > int eye_vrt; > > > int eye_term; > > > @@ -1040,6 +1068,130 @@ static int phy_type_set(struct > > > mtk_phy_instance *instance) > > > return 0; > > > } > > > > > > +static int phy_efuse_get(struct mtk_tphy *tphy, struct > > > mtk_phy_instance *instance) > > > +{ > > > + struct device *dev = &instance->phy->dev; > > > + int ret = 0; > > > + > > > + /* tphy v1 doesn't support sw efuse, skip it */ > > > + if (!tphy->pdata->sw_efuse_supported) { > > > + instance->efuse_sw_en = 0; > > > + return 0; > > > + } > > > + > > > + /* software efuse is optional */ > > > + instance->efuse_sw_en = device_property_read_bool(dev, "nvmem- > > > cells"); > > > + if (!instance->efuse_sw_en) > > > + return 0; > > > + > > > + switch (instance->type) { > > > + case PHY_TYPE_USB2: > > > + ret = nvmem_cell_read_variable_le_u32(dev, "intr", > > > &instance->efuse_intr); > > > + if (ret) { > > > + dev_err(dev, "fail to get u2 intr efuse, %d\n", > > > ret); > > > + break; > > > + } > > > + > > > + /* no efuse, ignore it */ > > > + if (!instance->efuse_intr) { > > > + dev_warn(dev, "no u2 intr efuse, but dts enable > > > it\n"); > > > + instance->efuse_sw_en = 0; > > > + break; > > > + } > > > > What does this check do...? so a zero value is not valid..? > Yes, because it's also zero for SoC without efuse, prefer to use > default value instead. > > > > > > + > > > + dev_info(dev, "u2 efuse - intr %x\n", instance- > > > >efuse_intr); > > > > dev_dbg()? > We usually use HW auto load way, print this log can help to point out > that it's specific SoC. You can enable this print thru dynamic debug or enable debug prints when debugging, let us not spam message log > > > > > > + break; > > > > empty line after break improves readability, pls add > Ok > > > > > + case PHY_TYPE_USB3: > > > + case PHY_TYPE_PCIE: > > > + ret = nvmem_cell_read_variable_le_u32(dev, "intr", > > > &instance->efuse_intr); > > > + if (ret) { > > > + dev_err(dev, "fail to get u3 intr efuse, %d\n", > > > ret); > > > + break; > > > + } > > > > This seems to be common, why not read this before switch? > It's not used for SGMII or SATA, but not applied until now > > > > > > + > > > + ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", > > > &instance->efuse_rx_imp); > > > + if (ret) { > > > + dev_err(dev, "fail to get u3 rx_imp efuse, > > > %d\n", ret); > > > + break; > > > + } > > > + > > > + ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", > > > &instance->efuse_tx_imp); > > > + if (ret) { > > > + dev_err(dev, "fail to get u3 tx_imp efuse, > > > %d\n", ret); > > > + break; > > > + } > > > + > > > + /* no efuse, ignore it */ > > > + if (!instance->efuse_intr && > > > + !instance->efuse_rx_imp && > > > + !instance->efuse_rx_imp) { > > > + dev_warn(dev, "no u3 intr efuse, but dts enable > > > it\n"); > > > + instance->efuse_sw_en = 0; > > > + break; > > > + } > > > > again, zero values are not valid? > It's also zero for SoC without efuse, treat it as invalid value > > > > > > + > > > + dev_info(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp > > > %x\n", > > > + instance->efuse_intr, instance->efuse_rx_imp, > > > + instance->efuse_tx_imp); > > > > dbg pls > Ok > > > > > + break; > > > + default: > > > + dev_err(dev, "no sw efuse for type %d\n", instance- > > > >type); > > > + ret = -EINVAL; > > > + } > > > + > > > + return ret; > > > +} > > > + > > > +static void phy_efuse_set(struct mtk_phy_instance *instance) > > > +{ > > > + struct device *dev = &instance->phy->dev; > > > + struct u2phy_banks *u2_banks = &instance->u2_banks; > > > + struct u3phy_banks *u3_banks = &instance->u3_banks; > > > + u32 tmp; > > > + > > > + if (!instance->efuse_sw_en) > > > + return; > > > + > > > + switch (instance->type) { > > > + case PHY_TYPE_USB2: > > > + tmp = readl(u2_banks->misc + U3P_MISC_REG1); > > > + tmp |= MR1_EFUSE_AUTO_LOAD_DIS; > > > + writel(tmp, u2_banks->misc + U3P_MISC_REG1); > > > + > > > + tmp = readl(u2_banks->com + U3P_USBPHYACR1); > > > + tmp &= ~PA1_RG_INTR_CAL; > > > + tmp |= PA1_RG_INTR_CAL_VAL(instance->efuse_intr); > > > + writel(tmp, u2_banks->com + U3P_USBPHYACR1); > > > + break; > > > + case PHY_TYPE_USB3: > > > + case PHY_TYPE_PCIE: > > > + tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); > > > + tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; > > > + writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV); > > > > add a updatel() macro and use this here and other places? > You mean add macro to set/clear bits? > If so, I need prepare another patch for this purpose Sure, that would be nice
On Thu, 2021-11-25 at 10:42 +0530, Vinod Koul wrote: > On 24-11-21, 14:54, Chunfeng Yun wrote: > > On Mon, 2021-11-22 at 17:05 +0530, Vinod Koul wrote: > > > On 07-11-21, 15:56, Chunfeng Yun wrote: > > > > Due to some SoCs have a bit shift issue that will drop a bit > > > > for > > > > usb3 > > > > phy or pcie phy, fix it by adding software efuse reading and > > > > setting, > > > > but only support it optionally for versoin 2/3. > > > > > > s/versoin/version > > > > Ok > > > > > > > > > > > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> > > > > --- > > > > drivers/phy/mediatek/phy-mtk-tphy.c | 162 > > > > ++++++++++++++++++++++++++++ > > > > 1 file changed, 162 insertions(+) > > > > > > > > diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c > > > > b/drivers/phy/mediatek/phy-mtk-tphy.c > > > > index cdcef865fe9e..3b5b1c266595 100644 > > > > --- a/drivers/phy/mediatek/phy-mtk-tphy.c > > > > +++ b/drivers/phy/mediatek/phy-mtk-tphy.c > > > > @@ -12,6 +12,7 @@ > > > > #include <linux/iopoll.h> > > > > #include <linux/mfd/syscon.h> > > > > #include <linux/module.h> > > > > +#include <linux/nvmem-consumer.h> > > > > #include <linux/of_address.h> > > > > #include <linux/of_device.h> > > > > #include <linux/phy/phy.h> > > > > @@ -41,6 +42,9 @@ > > > > #define SSUSB_SIFSLV_V2_U3PHYD 0x200 > > > > #define SSUSB_SIFSLV_V2_U3PHYA 0x400 > > > > > > > > +#define U3P_MISC_REG1 0x04 > > > > +#define MR1_EFUSE_AUTO_LOAD_DIS BIT(6) > > > > + > > > > #define U3P_USBPHYACR0 0x000 > > > > #define PA0_RG_U2PLL_FORCE_ON BIT(15) > > > > #define PA0_USB20_PLL_PREDIV GENMASK(7, 6) > > > > @@ -133,6 +137,8 @@ > > > > #define P3C_RG_SWRST_U3_PHYD_FORCE_EN BIT(24) > > > > > > > > #define U3P_U3_PHYA_REG0 0x000 > > > > +#define P3A_RG_IEXT_INTR GENMASK(15, 10) > > > > +#define P3A_RG_IEXT_INTR_VAL(x) ((0x3f & (x)) > > > > << 10) > > > > #define P3A_RG_CLKDRV_OFF GENMASK(3, 2) > > > > #define P3A_RG_CLKDRV_OFF_VAL(x) ((0x3 & (x)) << 2) > > > > > > > > @@ -187,6 +193,19 @@ > > > > #define P3D_RG_FWAKE_TH GENMASK(21, 16) > > > > #define P3D_RG_FWAKE_TH_VAL(x) ((0x3f & (x)) << 16) > > > > > > > > +#define U3P_U3_PHYD_IMPCAL0 0x010 > > > > +#define P3D_RG_FORCE_TX_IMPEL BIT(31) > > > > +#define P3D_RG_TX_IMPEL GENMASK(28, 24) > > > > +#define P3D_RG_TX_IMPEL_VAL(x) ((0x1f & (x)) << 24) > > > > + > > > > +#define U3P_U3_PHYD_IMPCAL1 0x014 > > > > +#define P3D_RG_FORCE_RX_IMPEL BIT(31) > > > > +#define P3D_RG_RX_IMPEL GENMASK(28, 24) > > > > +#define P3D_RG_RX_IMPEL_VAL(x) ((0x1f & (x)) << 24) > > > > + > > > > +#define U3P_U3_PHYD_RSV 0x054 > > > > +#define P3D_RG_EFUSE_AUTO_LOAD_DIS BIT(12) > > > > + > > > > #define U3P_U3_PHYD_CDR1 0x05c > > > > #define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24) > > > > #define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24) > > > > @@ -307,6 +326,11 @@ struct mtk_phy_pdata { > > > > * 48M PLL, fix it by switching PLL to 26M from default > > > > 48M > > > > */ > > > > bool sw_pll_48m_to_26m; > > > > + /* > > > > + * Some SoCs (e.g. mt8195) drop a bit when use auto > > > > load efuse, > > > > + * support sw way, also support it for v2/v3 > > > > optionally. > > > > + */ > > > > + bool sw_efuse_supported; > > > > enum mtk_phy_version version; > > > > }; > > > > > > > > @@ -336,6 +360,10 @@ struct mtk_phy_instance { > > > > struct regmap *type_sw; > > > > u32 type_sw_reg; > > > > u32 type_sw_index; > > > > + u32 efuse_sw_en; > > > > + u32 efuse_intr; > > > > + u32 efuse_tx_imp; > > > > + u32 efuse_rx_imp; > > > > int eye_src; > > > > int eye_vrt; > > > > int eye_term; > > > > @@ -1040,6 +1068,130 @@ static int phy_type_set(struct > > > > mtk_phy_instance *instance) > > > > return 0; > > > > } > > > > > > > > +static int phy_efuse_get(struct mtk_tphy *tphy, struct > > > > mtk_phy_instance *instance) > > > > +{ > > > > + struct device *dev = &instance->phy->dev; > > > > + int ret = 0; > > > > + > > > > + /* tphy v1 doesn't support sw efuse, skip it */ > > > > + if (!tphy->pdata->sw_efuse_supported) { > > > > + instance->efuse_sw_en = 0; > > > > + return 0; > > > > + } > > > > + > > > > + /* software efuse is optional */ > > > > + instance->efuse_sw_en = device_property_read_bool(dev, > > > > "nvmem- > > > > cells"); > > > > + if (!instance->efuse_sw_en) > > > > + return 0; > > > > + > > > > + switch (instance->type) { > > > > + case PHY_TYPE_USB2: > > > > + ret = nvmem_cell_read_variable_le_u32(dev, > > > > "intr", > > > > &instance->efuse_intr); > > > > + if (ret) { > > > > + dev_err(dev, "fail to get u2 intr > > > > efuse, %d\n", > > > > ret); > > > > + break; > > > > + } > > > > + > > > > + /* no efuse, ignore it */ > > > > + if (!instance->efuse_intr) { > > > > + dev_warn(dev, "no u2 intr efuse, but > > > > dts enable > > > > it\n"); > > > > + instance->efuse_sw_en = 0; > > > > + break; > > > > + } > > > > > > What does this check do...? so a zero value is not valid..? > > > > Yes, because it's also zero for SoC without efuse, prefer to use > > default value instead. > > > > > > > > > + > > > > + dev_info(dev, "u2 efuse - intr %x\n", instance- > > > > > efuse_intr); > > > > > > dev_dbg()? > > > > We usually use HW auto load way, print this log can help to point > > out > > that it's specific SoC. > > You can enable this print thru dynamic debug or enable debug prints > when > debugging, let us not spam message log Ok, will use dev_dbg() > > > > > > > > > > + break; > > > > > > empty line after break improves readability, pls add > > > > Ok > > > > > > > + case PHY_TYPE_USB3: > > > > + case PHY_TYPE_PCIE: > > > > + ret = nvmem_cell_read_variable_le_u32(dev, > > > > "intr", > > > > &instance->efuse_intr); > > > > + if (ret) { > > > > + dev_err(dev, "fail to get u3 intr > > > > efuse, %d\n", > > > > ret); > > > > + break; > > > > + } > > > > > > This seems to be common, why not read this before switch? > > > > It's not used for SGMII or SATA, but not applied until now > > > > > > > > > + > > > > + ret = nvmem_cell_read_variable_le_u32(dev, > > > > "rx_imp", > > > > &instance->efuse_rx_imp); > > > > + if (ret) { > > > > + dev_err(dev, "fail to get u3 rx_imp > > > > efuse, > > > > %d\n", ret); > > > > + break; > > > > + } > > > > + > > > > + ret = nvmem_cell_read_variable_le_u32(dev, > > > > "tx_imp", > > > > &instance->efuse_tx_imp); > > > > + if (ret) { > > > > + dev_err(dev, "fail to get u3 tx_imp > > > > efuse, > > > > %d\n", ret); > > > > + break; > > > > + } > > > > + > > > > + /* no efuse, ignore it */ > > > > + if (!instance->efuse_intr && > > > > + !instance->efuse_rx_imp && > > > > + !instance->efuse_rx_imp) { > > > > + dev_warn(dev, "no u3 intr efuse, but > > > > dts enable > > > > it\n"); > > > > + instance->efuse_sw_en = 0; > > > > + break; > > > > + } > > > > > > again, zero values are not valid? > > > > It's also zero for SoC without efuse, treat it as invalid value > > > > > > > > > + > > > > + dev_info(dev, "u3 efuse - intr %x, rx_imp %x, > > > > tx_imp > > > > %x\n", > > > > + instance->efuse_intr, instance- > > > > >efuse_rx_imp, > > > > + instance->efuse_tx_imp); > > > > > > dbg pls > > > > Ok > > > > > > > + break; > > > > + default: > > > > + dev_err(dev, "no sw efuse for type %d\n", > > > > instance- > > > > > type); > > > > > > > > + ret = -EINVAL; > > > > + } > > > > + > > > > + return ret; > > > > +} > > > > + > > > > +static void phy_efuse_set(struct mtk_phy_instance *instance) > > > > +{ > > > > + struct device *dev = &instance->phy->dev; > > > > + struct u2phy_banks *u2_banks = &instance->u2_banks; > > > > + struct u3phy_banks *u3_banks = &instance->u3_banks; > > > > + u32 tmp; > > > > + > > > > + if (!instance->efuse_sw_en) > > > > + return; > > > > + > > > > + switch (instance->type) { > > > > + case PHY_TYPE_USB2: > > > > + tmp = readl(u2_banks->misc + U3P_MISC_REG1); > > > > + tmp |= MR1_EFUSE_AUTO_LOAD_DIS; > > > > + writel(tmp, u2_banks->misc + U3P_MISC_REG1); > > > > + > > > > + tmp = readl(u2_banks->com + U3P_USBPHYACR1); > > > > + tmp &= ~PA1_RG_INTR_CAL; > > > > + tmp |= PA1_RG_INTR_CAL_VAL(instance- > > > > >efuse_intr); > > > > + writel(tmp, u2_banks->com + U3P_USBPHYACR1); > > > > + break; > > > > + case PHY_TYPE_USB3: > > > > + case PHY_TYPE_PCIE: > > > > + tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); > > > > + tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; > > > > + writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV); > > > > > > add a updatel() macro and use this here and other places? > > > > You mean add macro to set/clear bits? > > If so, I need prepare another patch for this purpose > > Sure, that would be nice Ok >
diff --git a/drivers/phy/mediatek/phy-mtk-tphy.c b/drivers/phy/mediatek/phy-mtk-tphy.c index cdcef865fe9e..3b5b1c266595 100644 --- a/drivers/phy/mediatek/phy-mtk-tphy.c +++ b/drivers/phy/mediatek/phy-mtk-tphy.c @@ -12,6 +12,7 @@ #include <linux/iopoll.h> #include <linux/mfd/syscon.h> #include <linux/module.h> +#include <linux/nvmem-consumer.h> #include <linux/of_address.h> #include <linux/of_device.h> #include <linux/phy/phy.h> @@ -41,6 +42,9 @@ #define SSUSB_SIFSLV_V2_U3PHYD 0x200 #define SSUSB_SIFSLV_V2_U3PHYA 0x400 +#define U3P_MISC_REG1 0x04 +#define MR1_EFUSE_AUTO_LOAD_DIS BIT(6) + #define U3P_USBPHYACR0 0x000 #define PA0_RG_U2PLL_FORCE_ON BIT(15) #define PA0_USB20_PLL_PREDIV GENMASK(7, 6) @@ -133,6 +137,8 @@ #define P3C_RG_SWRST_U3_PHYD_FORCE_EN BIT(24) #define U3P_U3_PHYA_REG0 0x000 +#define P3A_RG_IEXT_INTR GENMASK(15, 10) +#define P3A_RG_IEXT_INTR_VAL(x) ((0x3f & (x)) << 10) #define P3A_RG_CLKDRV_OFF GENMASK(3, 2) #define P3A_RG_CLKDRV_OFF_VAL(x) ((0x3 & (x)) << 2) @@ -187,6 +193,19 @@ #define P3D_RG_FWAKE_TH GENMASK(21, 16) #define P3D_RG_FWAKE_TH_VAL(x) ((0x3f & (x)) << 16) +#define U3P_U3_PHYD_IMPCAL0 0x010 +#define P3D_RG_FORCE_TX_IMPEL BIT(31) +#define P3D_RG_TX_IMPEL GENMASK(28, 24) +#define P3D_RG_TX_IMPEL_VAL(x) ((0x1f & (x)) << 24) + +#define U3P_U3_PHYD_IMPCAL1 0x014 +#define P3D_RG_FORCE_RX_IMPEL BIT(31) +#define P3D_RG_RX_IMPEL GENMASK(28, 24) +#define P3D_RG_RX_IMPEL_VAL(x) ((0x1f & (x)) << 24) + +#define U3P_U3_PHYD_RSV 0x054 +#define P3D_RG_EFUSE_AUTO_LOAD_DIS BIT(12) + #define U3P_U3_PHYD_CDR1 0x05c #define P3D_RG_CDR_BIR_LTD1 GENMASK(28, 24) #define P3D_RG_CDR_BIR_LTD1_VAL(x) ((0x1f & (x)) << 24) @@ -307,6 +326,11 @@ struct mtk_phy_pdata { * 48M PLL, fix it by switching PLL to 26M from default 48M */ bool sw_pll_48m_to_26m; + /* + * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse, + * support sw way, also support it for v2/v3 optionally. + */ + bool sw_efuse_supported; enum mtk_phy_version version; }; @@ -336,6 +360,10 @@ struct mtk_phy_instance { struct regmap *type_sw; u32 type_sw_reg; u32 type_sw_index; + u32 efuse_sw_en; + u32 efuse_intr; + u32 efuse_tx_imp; + u32 efuse_rx_imp; int eye_src; int eye_vrt; int eye_term; @@ -1040,6 +1068,130 @@ static int phy_type_set(struct mtk_phy_instance *instance) return 0; } +static int phy_efuse_get(struct mtk_tphy *tphy, struct mtk_phy_instance *instance) +{ + struct device *dev = &instance->phy->dev; + int ret = 0; + + /* tphy v1 doesn't support sw efuse, skip it */ + if (!tphy->pdata->sw_efuse_supported) { + instance->efuse_sw_en = 0; + return 0; + } + + /* software efuse is optional */ + instance->efuse_sw_en = device_property_read_bool(dev, "nvmem-cells"); + if (!instance->efuse_sw_en) + return 0; + + switch (instance->type) { + case PHY_TYPE_USB2: + ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr); + if (ret) { + dev_err(dev, "fail to get u2 intr efuse, %d\n", ret); + break; + } + + /* no efuse, ignore it */ + if (!instance->efuse_intr) { + dev_warn(dev, "no u2 intr efuse, but dts enable it\n"); + instance->efuse_sw_en = 0; + break; + } + + dev_info(dev, "u2 efuse - intr %x\n", instance->efuse_intr); + break; + case PHY_TYPE_USB3: + case PHY_TYPE_PCIE: + ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr); + if (ret) { + dev_err(dev, "fail to get u3 intr efuse, %d\n", ret); + break; + } + + ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", &instance->efuse_rx_imp); + if (ret) { + dev_err(dev, "fail to get u3 rx_imp efuse, %d\n", ret); + break; + } + + ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", &instance->efuse_tx_imp); + if (ret) { + dev_err(dev, "fail to get u3 tx_imp efuse, %d\n", ret); + break; + } + + /* no efuse, ignore it */ + if (!instance->efuse_intr && + !instance->efuse_rx_imp && + !instance->efuse_rx_imp) { + dev_warn(dev, "no u3 intr efuse, but dts enable it\n"); + instance->efuse_sw_en = 0; + break; + } + + dev_info(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n", + instance->efuse_intr, instance->efuse_rx_imp, + instance->efuse_tx_imp); + break; + default: + dev_err(dev, "no sw efuse for type %d\n", instance->type); + ret = -EINVAL; + } + + return ret; +} + +static void phy_efuse_set(struct mtk_phy_instance *instance) +{ + struct device *dev = &instance->phy->dev; + struct u2phy_banks *u2_banks = &instance->u2_banks; + struct u3phy_banks *u3_banks = &instance->u3_banks; + u32 tmp; + + if (!instance->efuse_sw_en) + return; + + switch (instance->type) { + case PHY_TYPE_USB2: + tmp = readl(u2_banks->misc + U3P_MISC_REG1); + tmp |= MR1_EFUSE_AUTO_LOAD_DIS; + writel(tmp, u2_banks->misc + U3P_MISC_REG1); + + tmp = readl(u2_banks->com + U3P_USBPHYACR1); + tmp &= ~PA1_RG_INTR_CAL; + tmp |= PA1_RG_INTR_CAL_VAL(instance->efuse_intr); + writel(tmp, u2_banks->com + U3P_USBPHYACR1); + break; + case PHY_TYPE_USB3: + case PHY_TYPE_PCIE: + tmp = readl(u3_banks->phyd + U3P_U3_PHYD_RSV); + tmp |= P3D_RG_EFUSE_AUTO_LOAD_DIS; + writel(tmp, u3_banks->phyd + U3P_U3_PHYD_RSV); + + tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0); + tmp &= ~P3D_RG_TX_IMPEL; + tmp |= P3D_RG_TX_IMPEL_VAL(instance->efuse_tx_imp); + tmp |= P3D_RG_FORCE_TX_IMPEL; + writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL0); + + tmp = readl(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1); + tmp &= ~P3D_RG_RX_IMPEL; + tmp |= P3D_RG_RX_IMPEL_VAL(instance->efuse_rx_imp); + tmp |= P3D_RG_FORCE_RX_IMPEL; + writel(tmp, u3_banks->phyd + U3P_U3_PHYD_IMPCAL1); + + tmp = readl(u3_banks->phya + U3P_U3_PHYA_REG0); + tmp &= ~P3A_RG_IEXT_INTR; + tmp |= P3A_RG_IEXT_INTR_VAL(instance->efuse_intr); + writel(tmp, u3_banks->phya + U3P_U3_PHYA_REG0); + break; + default: + dev_warn(dev, "no sw efuse for type %d\n", instance->type); + break; + } +} + static int mtk_phy_init(struct phy *phy) { struct mtk_phy_instance *instance = phy_get_drvdata(phy); @@ -1050,6 +1202,8 @@ static int mtk_phy_init(struct phy *phy) if (ret) return ret; + phy_efuse_set(instance); + switch (instance->type) { case PHY_TYPE_USB2: u2_phy_instance_init(tphy, instance); @@ -1134,6 +1288,7 @@ static struct phy *mtk_phy_xlate(struct device *dev, struct mtk_phy_instance *instance = NULL; struct device_node *phy_np = args->np; int index; + int ret; if (args->args_count != 1) { dev_err(dev, "invalid number of cells in 'phy' property\n"); @@ -1174,6 +1329,10 @@ static struct phy *mtk_phy_xlate(struct device *dev, return ERR_PTR(-EINVAL); } + ret = phy_efuse_get(tphy, instance); + if (ret) + return ERR_PTR(ret); + phy_parse_property(tphy, instance); phy_type_set(instance); @@ -1196,10 +1355,12 @@ static const struct mtk_phy_pdata tphy_v1_pdata = { static const struct mtk_phy_pdata tphy_v2_pdata = { .avoid_rx_sen_degradation = false, + .sw_efuse_supported = true, .version = MTK_PHY_V2, }; static const struct mtk_phy_pdata tphy_v3_pdata = { + .sw_efuse_supported = true, .version = MTK_PHY_V3, }; @@ -1210,6 +1371,7 @@ static const struct mtk_phy_pdata mt8173_pdata = { static const struct mtk_phy_pdata mt8195_pdata = { .sw_pll_48m_to_26m = true, + .sw_efuse_supported = true, .version = MTK_PHY_V3, };
Due to some SoCs have a bit shift issue that will drop a bit for usb3 phy or pcie phy, fix it by adding software efuse reading and setting, but only support it optionally for versoin 2/3. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> --- drivers/phy/mediatek/phy-mtk-tphy.c | 162 ++++++++++++++++++++++++++++ 1 file changed, 162 insertions(+)