Message ID | 20211213024057.3824985-5-gwendal@chromium.org (mailing list archive) |
---|---|
State | Changes Requested |
Headers | show |
Series | Add Semtech SX9360 SAR Sensor support | expand |
Quoting Gwendal Grignou (2021-12-12 18:40:57) > Add support to configure sx9360 from dt-binding, to match device > hardware setup. > > Signed-off-by: Gwendal Grignou <gwendal@chromium.org> > --- Reviewed-by: Stephen Boyd <swboyd@chromium.org>
On Sun, 12 Dec 2021 18:40:57 -0800 Gwendal Grignou <gwendal@chromium.org> wrote: > Add support to configure sx9360 from dt-binding, to match device > hardware setup. > > Signed-off-by: Gwendal Grignou <gwendal@chromium.org> This and patch 3 look fine to me, so mostly just a question of modifier vs label for the reference channel. Thanks, Jonathan > --- > Changes since v2: > - Add include when needed. > - Move default register constant to main patch. > > No changes in v2. > > drivers/iio/proximity/sx9360.c | 85 +++++++++++++++++++++++++++++++++- > 1 file changed, 84 insertions(+), 1 deletion(-) > > diff --git a/drivers/iio/proximity/sx9360.c b/drivers/iio/proximity/sx9360.c > index aebfbe541e0e04..30cc6549d301e6 100644 > --- a/drivers/iio/proximity/sx9360.c > +++ b/drivers/iio/proximity/sx9360.c > @@ -18,6 +18,7 @@ > #include <linux/mod_devicetable.h> > #include <linux/module.h> > #include <linux/pm.h> > +#include <linux/property.h> > #include <linux/regmap.h> > > #include <linux/iio/iio.h> > @@ -64,6 +65,7 @@ > #define SX9360_REG_PROX_CTRL0_PHM 0x41 > #define SX9360_REG_PROX_CTRL0_GAIN_MASK GENMASK(5, 3) > #define SX9360_REG_PROX_CTRL0_GAIN_1 0x80 > +#define SX9360_REG_PROX_CTRL0_RAWFILT_MASK GENMASK(2, 0) > #define SX9360_REG_PROX_CTRL0_RAWFILT_1P50 0x01 > #define SX9360_REG_PROX_CTRL1 0x42 > #define SX9360_REG_PROX_CTRL1_AVGNEG_THRESH_MASK GENMASK(5, 3) > @@ -647,6 +649,41 @@ static int sx9360_write_raw(struct iio_dev *indio_dev, > return -EINVAL; > } > > +static const struct sx_common_reg_default sx9360_default_regs[] = { > + { SX9360_REG_IRQ_MSK, 0x00 }, > + { SX9360_REG_IRQ_CFG, 0x00 }, > + /* > + * The lower 2 bits should not be set as it enable sensors measurements. > + * Turning the detection on before the configuration values are set to > + * good values can cause the device to return erroneous readings. > + */ > + { SX9360_REG_GNRL_CTRL0, 0x00 }, > + { SX9360_REG_GNRL_CTRL1, 0x00 }, > + { SX9360_REG_GNRL_CTRL2, SX9360_REG_GNRL_CTRL2_PERIOD_102MS }, > + > + { SX9360_REG_AFE_CTRL1, 0x00 }, > + { SX9360_REG_AFE_PARAM0_PHR, SX9360_REG_AFE_PARAM0_RSVD | > + SX9360_REG_AFE_PARAM0_RESOLUTION_128 }, > + { SX9360_REG_AFE_PARAM1_PHR, SX9360_REG_AFE_PARAM1_AGAIN_PHM_6PF | > + SX9360_REG_AFE_PARAM1_FREQ_83_33HZ }, > + { SX9360_REG_AFE_PARAM0_PHM, SX9360_REG_AFE_PARAM0_RSVD | > + SX9360_REG_AFE_PARAM0_RESOLUTION_128 }, > + { SX9360_REG_AFE_PARAM1_PHM, SX9360_REG_AFE_PARAM1_AGAIN_PHM_6PF | > + SX9360_REG_AFE_PARAM1_FREQ_83_33HZ }, > + > + { SX9360_REG_PROX_CTRL0_PHR, SX9360_REG_PROX_CTRL0_GAIN_1 | > + SX9360_REG_PROX_CTRL0_RAWFILT_1P50 }, > + { SX9360_REG_PROX_CTRL0_PHM, SX9360_REG_PROX_CTRL0_GAIN_1 | > + SX9360_REG_PROX_CTRL0_RAWFILT_1P50 }, > + { SX9360_REG_PROX_CTRL1, SX9360_REG_PROX_CTRL1_AVGNEG_THRESH_16K }, > + { SX9360_REG_PROX_CTRL2, SX9360_REG_PROX_CTRL2_AVGDEB_2SAMPLES | > + SX9360_REG_PROX_CTRL2_AVGPOS_THRESH_16K }, > + { SX9360_REG_PROX_CTRL3, SX9360_REG_PROX_CTRL3_AVGNEG_FILT_2 | > + SX9360_REG_PROX_CTRL3_AVGPOS_FILT_256 }, > + { SX9360_REG_PROX_CTRL4, 0x00 }, > + { SX9360_REG_PROX_CTRL5, SX9360_REG_PROX_CTRL5_PROXTHRESH_32 }, > +}; > + > /* Activate all channels and perform an initial compensation. */ > static int sx9360_init_compensation(struct iio_dev *indio_dev) > { > @@ -671,6 +708,51 @@ static int sx9360_init_compensation(struct iio_dev *indio_dev) > return ret; > } > > +static const struct sx_common_reg_default * > +sx9360_get_default_reg(struct device *dev, int idx, > + struct sx_common_reg_default *reg_def) > +{ > + u32 raw = 0, pos = 0; > + int ret; > + > + memcpy(reg_def, &sx9360_default_regs[idx], sizeof(*reg_def)); > + switch (reg_def->reg) { > + case SX9360_REG_AFE_PARAM0_PHR: > + case SX9360_REG_AFE_PARAM0_PHM: > + ret = device_property_read_u32(dev, "semtech,resolution", &raw); > + if (ret) > + break; > + > + raw = ilog2(raw) - 3; > + > + reg_def->def &= ~SX9360_REG_AFE_PARAM0_RESOLUTION_MASK; > + reg_def->def |= FIELD_PREP(SX9360_REG_AFE_PARAM0_RESOLUTION_MASK, raw); > + break; > + case SX9360_REG_PROX_CTRL0_PHR: > + case SX9360_REG_PROX_CTRL0_PHM: > + ret = device_property_read_u32(dev, "semtech,proxraw-strength", &raw); > + if (ret) > + break; > + > + reg_def->def &= ~SX9360_REG_PROX_CTRL0_RAWFILT_MASK; > + reg_def->def |= FIELD_PREP(SX9360_REG_PROX_CTRL0_RAWFILT_MASK, raw); > + break; > + case SX9360_REG_PROX_CTRL3: > + ret = device_property_read_u32(dev, "semtech,avg-pos-strength", > + &pos); > + if (ret) > + break; > + > + /* Powers of 2, except for a gap between 16 and 64 */ > + raw = clamp(ilog2(pos), 3, 11) - (pos >= 32 ? 4 : 3); > + reg_def->def &= ~SX9360_REG_PROX_CTRL3_AVGPOS_FILT_MASK; > + reg_def->def |= FIELD_PREP(SX9360_REG_PROX_CTRL3_AVGPOS_FILT_MASK, raw); > + break; > + } > + > + return reg_def; > +} > + > static int sx9360_check_whoami(struct device *dev, > struct iio_dev *indio_dev) > { > @@ -691,12 +773,14 @@ static const struct sx_common_chip_info sx9360_chip_info = { > .mask_enable_chan = SX9360_REG_GNRL_CTRL0_PHEN_MASK, > .stat_offset = 3, > .num_channels = SX9360_NUM_CHANNELS, > + .num_default_regs = ARRAY_SIZE(sx9360_default_regs), > > .ops = { > .read_prox_data = sx9360_read_prox_data, > .check_whoami = sx9360_check_whoami, > .init_compensation = sx9360_init_compensation, > .wait_for_sample = sx9360_wait_for_sample, > + .get_default_reg = sx9360_get_default_reg, > }, > > .iio_channels = sx9360_channels,
diff --git a/drivers/iio/proximity/sx9360.c b/drivers/iio/proximity/sx9360.c index aebfbe541e0e04..30cc6549d301e6 100644 --- a/drivers/iio/proximity/sx9360.c +++ b/drivers/iio/proximity/sx9360.c @@ -18,6 +18,7 @@ #include <linux/mod_devicetable.h> #include <linux/module.h> #include <linux/pm.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/iio/iio.h> @@ -64,6 +65,7 @@ #define SX9360_REG_PROX_CTRL0_PHM 0x41 #define SX9360_REG_PROX_CTRL0_GAIN_MASK GENMASK(5, 3) #define SX9360_REG_PROX_CTRL0_GAIN_1 0x80 +#define SX9360_REG_PROX_CTRL0_RAWFILT_MASK GENMASK(2, 0) #define SX9360_REG_PROX_CTRL0_RAWFILT_1P50 0x01 #define SX9360_REG_PROX_CTRL1 0x42 #define SX9360_REG_PROX_CTRL1_AVGNEG_THRESH_MASK GENMASK(5, 3) @@ -647,6 +649,41 @@ static int sx9360_write_raw(struct iio_dev *indio_dev, return -EINVAL; } +static const struct sx_common_reg_default sx9360_default_regs[] = { + { SX9360_REG_IRQ_MSK, 0x00 }, + { SX9360_REG_IRQ_CFG, 0x00 }, + /* + * The lower 2 bits should not be set as it enable sensors measurements. + * Turning the detection on before the configuration values are set to + * good values can cause the device to return erroneous readings. + */ + { SX9360_REG_GNRL_CTRL0, 0x00 }, + { SX9360_REG_GNRL_CTRL1, 0x00 }, + { SX9360_REG_GNRL_CTRL2, SX9360_REG_GNRL_CTRL2_PERIOD_102MS }, + + { SX9360_REG_AFE_CTRL1, 0x00 }, + { SX9360_REG_AFE_PARAM0_PHR, SX9360_REG_AFE_PARAM0_RSVD | + SX9360_REG_AFE_PARAM0_RESOLUTION_128 }, + { SX9360_REG_AFE_PARAM1_PHR, SX9360_REG_AFE_PARAM1_AGAIN_PHM_6PF | + SX9360_REG_AFE_PARAM1_FREQ_83_33HZ }, + { SX9360_REG_AFE_PARAM0_PHM, SX9360_REG_AFE_PARAM0_RSVD | + SX9360_REG_AFE_PARAM0_RESOLUTION_128 }, + { SX9360_REG_AFE_PARAM1_PHM, SX9360_REG_AFE_PARAM1_AGAIN_PHM_6PF | + SX9360_REG_AFE_PARAM1_FREQ_83_33HZ }, + + { SX9360_REG_PROX_CTRL0_PHR, SX9360_REG_PROX_CTRL0_GAIN_1 | + SX9360_REG_PROX_CTRL0_RAWFILT_1P50 }, + { SX9360_REG_PROX_CTRL0_PHM, SX9360_REG_PROX_CTRL0_GAIN_1 | + SX9360_REG_PROX_CTRL0_RAWFILT_1P50 }, + { SX9360_REG_PROX_CTRL1, SX9360_REG_PROX_CTRL1_AVGNEG_THRESH_16K }, + { SX9360_REG_PROX_CTRL2, SX9360_REG_PROX_CTRL2_AVGDEB_2SAMPLES | + SX9360_REG_PROX_CTRL2_AVGPOS_THRESH_16K }, + { SX9360_REG_PROX_CTRL3, SX9360_REG_PROX_CTRL3_AVGNEG_FILT_2 | + SX9360_REG_PROX_CTRL3_AVGPOS_FILT_256 }, + { SX9360_REG_PROX_CTRL4, 0x00 }, + { SX9360_REG_PROX_CTRL5, SX9360_REG_PROX_CTRL5_PROXTHRESH_32 }, +}; + /* Activate all channels and perform an initial compensation. */ static int sx9360_init_compensation(struct iio_dev *indio_dev) { @@ -671,6 +708,51 @@ static int sx9360_init_compensation(struct iio_dev *indio_dev) return ret; } +static const struct sx_common_reg_default * +sx9360_get_default_reg(struct device *dev, int idx, + struct sx_common_reg_default *reg_def) +{ + u32 raw = 0, pos = 0; + int ret; + + memcpy(reg_def, &sx9360_default_regs[idx], sizeof(*reg_def)); + switch (reg_def->reg) { + case SX9360_REG_AFE_PARAM0_PHR: + case SX9360_REG_AFE_PARAM0_PHM: + ret = device_property_read_u32(dev, "semtech,resolution", &raw); + if (ret) + break; + + raw = ilog2(raw) - 3; + + reg_def->def &= ~SX9360_REG_AFE_PARAM0_RESOLUTION_MASK; + reg_def->def |= FIELD_PREP(SX9360_REG_AFE_PARAM0_RESOLUTION_MASK, raw); + break; + case SX9360_REG_PROX_CTRL0_PHR: + case SX9360_REG_PROX_CTRL0_PHM: + ret = device_property_read_u32(dev, "semtech,proxraw-strength", &raw); + if (ret) + break; + + reg_def->def &= ~SX9360_REG_PROX_CTRL0_RAWFILT_MASK; + reg_def->def |= FIELD_PREP(SX9360_REG_PROX_CTRL0_RAWFILT_MASK, raw); + break; + case SX9360_REG_PROX_CTRL3: + ret = device_property_read_u32(dev, "semtech,avg-pos-strength", + &pos); + if (ret) + break; + + /* Powers of 2, except for a gap between 16 and 64 */ + raw = clamp(ilog2(pos), 3, 11) - (pos >= 32 ? 4 : 3); + reg_def->def &= ~SX9360_REG_PROX_CTRL3_AVGPOS_FILT_MASK; + reg_def->def |= FIELD_PREP(SX9360_REG_PROX_CTRL3_AVGPOS_FILT_MASK, raw); + break; + } + + return reg_def; +} + static int sx9360_check_whoami(struct device *dev, struct iio_dev *indio_dev) { @@ -691,12 +773,14 @@ static const struct sx_common_chip_info sx9360_chip_info = { .mask_enable_chan = SX9360_REG_GNRL_CTRL0_PHEN_MASK, .stat_offset = 3, .num_channels = SX9360_NUM_CHANNELS, + .num_default_regs = ARRAY_SIZE(sx9360_default_regs), .ops = { .read_prox_data = sx9360_read_prox_data, .check_whoami = sx9360_check_whoami, .init_compensation = sx9360_init_compensation, .wait_for_sample = sx9360_wait_for_sample, + .get_default_reg = sx9360_get_default_reg, }, .iio_channels = sx9360_channels,
Add support to configure sx9360 from dt-binding, to match device hardware setup. Signed-off-by: Gwendal Grignou <gwendal@chromium.org> --- Changes since v2: - Add include when needed. - Move default register constant to main patch. No changes in v2. drivers/iio/proximity/sx9360.c | 85 +++++++++++++++++++++++++++++++++- 1 file changed, 84 insertions(+), 1 deletion(-)