| Message ID | 20211203035601.3505780-1-bjorn.andersson@linaro.org (mailing list archive) |
|---|---|
| State | Changes Requested, archived |
| Headers | show |
| Series | clk: qcom: rcg2: Cache rate changes for parked RCGs | expand |
On 12/2/21 9:56 PM, Bjorn Andersson wrote: > As GDSCs are turned on and off some associated clocks are momentarily > enabled for house keeping purposes. Failure to enable these clocks seems > to have been silently ignored in the past, but starting in SM8350 this > failure will prevent the GDSC to turn on. > > At least on SM8350 this operation will enable the RCG per the > configuration in CFG_REG. This means that the current model where the > current configuration is written back to CF_REG immediately after > parking the RCG doesn't work. > > Instead, keep track of the currently requested rate of the clock and > upon enabling the clock reapply the configuration per the saved rate. > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > --- > drivers/clk/qcom/clk-rcg.h | 2 ++ > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- > 2 files changed, 19 insertions(+), 15 deletions(-) > > <snip patch> With this applied, I'm getting [ 28.404134] ------------[ cut here ]------------ [ 28.404448] video_cc_venus_clk_src: rcg didn't update its configuration. [ 28.405500] WARNING: CPU: 7 PID: 372 at drivers/clk/qcom/clk-rcg2.c:122 update_config+0xd0/0xe0 [ 28.405999] Modules linked in: snd_timer(+) snd hci_uart(+) soundcore btqca btrtl venus_core(+) btbcm v4l2_mem2mem videobuf2_v4l2 btintel bluetooth videobuf2_common videodev mc ecdh_generic hid_multitouch(+) ecc ath10k_snoc ath10k_core qcom_rng ath mac80211 qcom_q6v5_mss libarc4 cfg80211 rfkill sg qcom_wdt qcom_q6v5_pas evdev slim_qcom_ngd_ctrl qrtr qcom_pil_info pdr_interface qcom_q6v5 slimbus qcom_sysmon rmtfs_mem tcp_bbr sch_fq fuse configfs ip_tables x_tables autofs4 ext4 mbcache jbd2 panel_simple rtc_pm8xxx msm llcc_qcom ocmem ti_sn65dsi86 drm_dp_aux_bus gpu_sched drm_kms_helper drm camcc_sdm845 ipa qcom_common qmi_helpers mdt_loader gpio_keys pwm_bl [ 28.407149] CPU: 7 PID: 372 Comm: systemd-udevd Not tainted 5.15.6 #45 [ 28.407175] Hardware name: LENOVO 81JL/LNVNB161216, BIOS 9UCN33WW(V2.06) 06/ 4/2019 [ 28.407212] pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 28.407243] pc : update_config+0xd0/0xe0 [ 28.407261] lr : update_config+0xd0/0xe0 [ 28.407265] sp : ffff800010833620 [ 28.407268] x29: ffff800010833620 x28: ffffd0c345fa7000 x27: ffffd0c345fa7a80 [ 28.407274] x26: ffff2ed90222e100 x25: 0000000005f5e100 x24: 0000000000000000 [ 28.407288] x23: ffffd0c2fdc80cd0 x22: ffff2ed9092480c8 x21: ffffd0c345852bb0 [ 28.407293] x20: ffffd0c34615a9d0 x19: 0000000000000000 x18: ffffd0c346209900 [ 28.407305] x17: ffffd0c346209918 x16: ffffd0c344f7c4d0 x15: 00000000000500a8 [ 28.407309] x14: 0000000000000000 x13: 2e6e6f6974617275 x12: 6769666e6f632073 [ 28.407314] x11: ffffffffffff56a0 x10: ffffffffffff5658 x9 : ffffd0c34499b66c [ 28.407329] x8 : 00000000ffffefff x7 : ffffd0c34602b0a8 x6 : 0000000000017ce0 [ 28.407333] x5 : ffff2eda737e5a48 x4 : ffff800010833460 x3 : 0000000000000001 [ 28.407338] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff2ed90aa6e740 [ 28.407378] Call trace: [ 28.407425] update_config+0xd0/0xe0 [ 28.407429] clk_rcg2_shared_enable+0x74/0xb4 [ 28.407471] clk_core_enable+0x78/0x220 [ 28.407536] clk_core_enable+0x58/0x220 [ 28.407540] clk_enable+0x38/0x60 [ 28.407544] core_clks_enable+0xd8/0x160 [venus_core] [ 28.408358] core_power_v4+0xe0/0x150 [venus_core] [ 28.408419] venus_runtime_resume+0x70/0x90 [venus_core] [ 28.408451] pm_generic_runtime_resume+0x38/0x50 [ 28.408538] __rpm_callback+0x50/0x1b0 [ 28.408570] rpm_callback+0x74/0x80 [ 28.408588] rpm_resume+0x618/0x8b0 [ 28.408595] __pm_runtime_resume+0x4c/0xa4 [ 28.408599] venus_probe+0x2f8/0x4d0 [venus_core] [ 28.408616] platform_probe+0x74/0xf0 [ 28.408693] really_probe+0xc4/0x470 [ 28.408722] __driver_probe_device+0x11c/0x190 [ 28.408729] driver_probe_device+0x48/0x110 [ 28.408734] __driver_attach+0xd8/0x1f0 [ 28.408738] bus_for_each_dev+0x7c/0xe0 [ 28.408814] driver_attach+0x30/0x40 [ 28.408816] bus_add_driver+0x154/0x250 [ 28.408820] driver_register+0x84/0x140 [ 28.408823] __platform_driver_register+0x34/0x40 [ 28.408841] qcom_venus_driver_init+0x30/0x1000 [venus_core] [ 28.408857] do_one_initcall+0x50/0x240 [ 28.408955] do_init_module+0x60/0x270 [ 28.409106] load_module+0x2050/0x2460 [ 28.409109] __do_sys_finit_module+0xa8/0x114 [ 28.409130] __arm64_sys_finit_module+0x2c/0x3c [ 28.409139] invoke_syscall+0x50/0x120 [ 28.409272] el0_svc_common.constprop.0+0xdc/0x100 [ 28.409295] do_el0_svc+0x34/0xa0 [ 28.409307] el0_svc+0x28/0x80 [ 28.409426] el0t_64_sync_handler+0xa4/0x130 [ 28.409430] el0t_64_sync+0x1a0/0x1a4 [ 28.409453] ---[ end trace f08b1f47ee3d43ed ]--- And a blank screen - it seems similar to the "blue" screen that I see every few reboots, however this time, closing the lid and letting it suspend and then waking back up by opening it up - during the suspend, we get: [ 141.357919] ldo1: Underflow of regulator enable count [ 141.357940] Failed to disable vdds: -EINVAL [ 141.606278] ------------[ cut here ]------------ [ 141.606368] disp_cc_mdss_ahb_clk already disabled [ 141.607229] WARNING: CPU: 3 PID: 1277 at drivers/clk/clk.c:952 clk_core_disable+0x1dc/0x1f4 [ 141.607470] Modules linked in: rfcomm xt_conntrack aes_ce_ccm nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlink nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xfrm_user xfrm_algo nft_counter snd_seq_dummy snd_hrtimer snd_seq snd_seq_device xt_addrtype nft_compat nf_tables libcrc32c nfnetlink br_netfilter bridge stp llc overlay q6asm_dai snd_soc_wsa881x regmap_sdw q6routing q6afe_dai soundwire_qcom snd_soc_wcd934x gpio_wcd934x q6adm snd_soc_wcd_mbhc cpufreq_ondemand cpufreq_conservative q6asm q6dsp_common cpufreq_powersave q6afe algif_hash algif_skcipher q6core af_alg bnep cpufreq_userspace lz4 lz4_compress wcd934x regmap_slimbus zram zsmalloc apr qrtr_smd fastrpc binfmt_misc snd_soc_sdm845 nls_ascii uvcvideo nls_cp437 videobuf2_vmalloc snd_soc_rt5663 vfat videobuf2_memops fat snd_soc_qcom_common snd_soc_rl6231 aes_ce_blk soundwire_bus crypto_simd cryptd aes_ce_cipher pm8941_pwrkey snd_soc_core snd_compress crct10dif_ce ghash_ce gf128mul snd_pcm_dmaengine sha2_ce sha256_arm64 [ 141.608446] qcom_spmi_adc5 snd_pcm sha1_ce qcom_vadc_common qcom_spmi_temp_alarm joydev industrialio snd_timer snd hci_uart soundcore btqca btrtl venus_core btbcm v4l2_mem2mem videobuf2_v4l2 btintel bluetooth videobuf2_common videodev mc ecdh_generic hid_multitouch ecc ath10k_snoc ath10k_core qcom_rng ath mac80211 qcom_q6v5_mss libarc4 cfg80211 rfkill sg qcom_wdt qcom_q6v5_pas evdev slim_qcom_ngd_ctrl qrtr qcom_pil_info pdr_interface qcom_q6v5 slimbus qcom_sysmon rmtfs_mem tcp_bbr sch_fq fuse configfs ip_tables x_tables autofs4 ext4 mbcache jbd2 panel_simple rtc_pm8xxx msm llcc_qcom ocmem ti_sn65dsi86 drm_dp_aux_bus gpu_sched drm_kms_helper drm camcc_sdm845 ipa qcom_common qmi_helpers mdt_loader gpio_keys pwm_bl [ 141.609150] CPU: 3 PID: 1277 Comm: systemd-sleep Tainted: G W 5.15.6 #45 [ 141.609184] Hardware name: LENOVO 81JL/LNVNB161216, BIOS 9UCN33WW(V2.06) 06/ 4/2019 [ 141.609204] pstate: 604000c5 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 141.609236] pc : clk_core_disable+0x1dc/0x1f4 [ 141.609265] lr : clk_core_disable+0x1dc/0x1f4 [ 141.609292] sp : ffff800017c63940 [ 141.609303] x29: ffff800017c63940 x28: ffff2ed900fb8118 x27: ffffd0c3450bbe20 [ 141.609348] x26: 0000000000000002 x25: 0000000000000000 x24: ffff2ed90bf23200 [ 141.609388] x23: ffffd0c3461a1590 x22: 0000000000000001 x21: ffff2ed90c90dd00 [ 141.609427] x20: ffff2ed909bccf00 x19: ffff2ed909bccf00 x18: 0000000000000000 [ 141.609466] x17: 000000040044ffff x16: ffffd0c344f7c154 x15: 0000000000000000 [ 141.609505] x14: ffff2ed900296740 x13: 0a64656c62617369 x12: 642079646165726c [ 141.609545] x11: 656820747563205b x10: 2d2d2d2d2d2d2d2d x9 : ffffd0c34499b66c [ 141.609584] x8 : 00000000ffffffff x7 : 656c626173696420 x6 : 00000000fffff633 [ 141.609622] x5 : ffff2eda73771a48 x4 : ffff800017c63780 x3 : 0000000000000001 [ 141.609659] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff2ed920b70000 [ 141.609700] Call trace: [ 141.609714] clk_core_disable+0x1dc/0x1f4 [ 141.609745] clk_disable+0x3c/0x5c [ 141.609773] msm_dsi_runtime_suspend+0x68/0x90 [msm] [ 141.610617] pm_generic_runtime_suspend+0x38/0x50 [ 141.610696] genpd_runtime_suspend+0xb4/0x314 [ 141.610761] pm_runtime_force_suspend+0x54/0x140 [ 141.610794] dpm_run_callback+0x60/0x180 [ 141.610816] __device_suspend+0x120/0x5a0 [ 141.610839] dpm_suspend+0x158/0x2c0 [ 141.610863] dpm_suspend_start+0xa8/0xb0 [ 141.610886] suspend_devices_and_enter+0x100/0x810 [ 141.610960] pm_suspend+0x38c/0x480 [ 141.610982] state_store+0x98/0x11c [ 141.611005] kobj_attr_store+0x1c/0x30 [ 141.611063] sysfs_kf_write+0x50/0x60 [ 141.611089] kernfs_fop_write_iter+0x134/0x1c4 [ 141.611140] new_sync_write+0xf0/0x18c [ 141.611192] vfs_write+0x210/0x2b0 [ 141.611220] ksys_write+0x74/0x100 [ 141.611246] __arm64_sys_write+0x28/0x3c [ 141.611275] invoke_syscall+0x50/0x120 [ 141.611339] el0_svc_common.constprop.0+0x4c/0x100 [ 141.611368] do_el0_svc+0x34/0xa0 [ 141.611393] el0_svc+0x28/0x80 [ 141.611431] el0t_64_sync_handler+0xa4/0x130 [ 141.611455] el0t_64_sync+0x1a0/0x1a4 [ 141.611483] ---[ end trace f08b1f47ee3d43ee ]--- [ 141.611653] ------------[ cut here ]------------ [ 141.611664] disp_cc_mdss_ahb_clk already unprepared [ 141.611831] WARNING: CPU: 3 PID: 1277 at drivers/clk/clk.c:810 clk_core_unprepare+0x1a0/0x1c0 [ 141.611880] Modules linked in: rfcomm xt_conntrack aes_ce_ccm nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlink nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xfrm_user xfrm_algo nft_counter snd_seq_dummy snd_hrtimer snd_seq snd_seq_device xt_addrtype nft_compat nf_tables libcrc32c nfnetlink br_netfilter bridge stp llc overlay q6asm_dai snd_soc_wsa881x regmap_sdw q6routing q6afe_dai soundwire_qcom snd_soc_wcd934x gpio_wcd934x q6adm snd_soc_wcd_mbhc cpufreq_ondemand cpufreq_conservative q6asm q6dsp_common cpufreq_powersave q6afe algif_hash algif_skcipher q6core af_alg bnep cpufreq_userspace lz4 lz4_compress wcd934x regmap_slimbus zram zsmalloc apr qrtr_smd fastrpc binfmt_misc snd_soc_sdm845 nls_ascii uvcvideo nls_cp437 videobuf2_vmalloc snd_soc_rt5663 vfat videobuf2_memops fat snd_soc_qcom_common snd_soc_rl6231 aes_ce_blk soundwire_bus crypto_simd cryptd aes_ce_cipher pm8941_pwrkey snd_soc_core snd_compress crct10dif_ce ghash_ce gf128mul snd_pcm_dmaengine sha2_ce sha256_arm64 [ 141.612553] qcom_spmi_adc5 snd_pcm sha1_ce qcom_vadc_common qcom_spmi_temp_alarm joydev industrialio snd_timer snd hci_uart soundcore btqca btrtl venus_core btbcm v4l2_mem2mem videobuf2_v4l2 btintel bluetooth videobuf2_common videodev mc ecdh_generic hid_multitouch ecc ath10k_snoc ath10k_core qcom_rng ath mac80211 qcom_q6v5_mss libarc4 cfg80211 rfkill sg qcom_wdt qcom_q6v5_pas evdev slim_qcom_ngd_ctrl qrtr qcom_pil_info pdr_interface qcom_q6v5 slimbus qcom_sysmon rmtfs_mem tcp_bbr sch_fq fuse configfs ip_tables x_tables autofs4 ext4 mbcache jbd2 panel_simple rtc_pm8xxx msm llcc_qcom ocmem ti_sn65dsi86 drm_dp_aux_bus gpu_sched drm_kms_helper drm camcc_sdm845 ipa qcom_common qmi_helpers mdt_loader gpio_keys pwm_bl [ 141.613142] CPU: 3 PID: 1277 Comm: systemd-sleep Tainted: G W 5.15.6 #45 [ 141.613167] Hardware name: LENOVO 81JL/LNVNB161216, BIOS 9UCN33WW(V2.06) 06/ 4/2019 [ 141.613181] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 141.613206] pc : clk_core_unprepare+0x1a0/0x1c0 [ 141.613236] lr : clk_core_unprepare+0x1a0/0x1c0 [ 141.613264] sp : ffff800017c63950 [ 141.613275] x29: ffff800017c63950 x28: ffff2ed900fb8118 x27: ffffd0c3450bbe20 [ 141.613318] x26: 0000000000000002 x25: 0000000000000000 x24: ffff2ed90bf23200 [ 141.613358] x23: ffffd0c3461a1590 x22: 0000000000000001 x21: ffff2ed90c90dd00 [ 141.613396] x20: ffff2ed900fa0c78 x19: ffff2ed909bccf00 x18: 0000000000000000 [ 141.613436] x17: 000000040044ffff x16: ffffd0c344f7bdf0 x15: 0000000000000000 [ 141.613475] x14: ffff2ed900296740 x13: 0a64657261706572 x12: 706e752079646165 [ 141.613515] x11: 656820747563205b x10: 2d2d2d2d2d2d2d2d x9 : ffffd0c34499b66c [ 141.613554] x8 : 00000000ffffffff x7 : 61706572706e7520 x6 : 00000000fffff664 [ 141.613592] x5 : ffff2eda73771a48 x4 : ffff800017c63790 x3 : 0000000000000001 [ 141.613629] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff2ed920b70000 [ 141.613667] Call trace: [ 141.613678] clk_core_unprepare+0x1a0/0x1c0 [ 141.613710] clk_unprepare+0x38/0x50 [ 141.613736] msm_dsi_runtime_suspend+0x70/0x90 [msm] [ 141.614063] pm_generic_runtime_suspend+0x38/0x50 [ 141.614091] genpd_runtime_suspend+0xb4/0x314 [ 141.614121] pm_runtime_force_suspend+0x54/0x140 [ 141.614151] dpm_run_callback+0x60/0x180 [ 141.614173] __device_suspend+0x120/0x5a0 [ 141.614195] dpm_suspend+0x158/0x2c0 [ 141.614218] dpm_suspend_start+0xa8/0xb0 [ 141.614241] suspend_devices_and_enter+0x100/0x810 [ 141.614267] pm_suspend+0x38c/0x480 [ 141.614290] state_store+0x98/0x11c [ 141.614311] kobj_attr_store+0x1c/0x30 [ 141.614340] sysfs_kf_write+0x50/0x60 [ 141.614360] kernfs_fop_write_iter+0x134/0x1c4 [ 141.614390] new_sync_write+0xf0/0x18c [ 141.614418] vfs_write+0x210/0x2b0 [ 141.614443] ksys_write+0x74/0x100 [ 141.614469] __arm64_sys_write+0x28/0x3c [ 141.614496] invoke_syscall+0x50/0x120 [ 141.614523] el0_svc_common.constprop.0+0x4c/0x100 [ 141.614551] do_el0_svc+0x34/0xa0 [ 141.614576] el0_svc+0x28/0x80 [ 141.614597] el0t_64_sync_handler+0xa4/0x130 [ 141.614621] el0t_64_sync+0x1a0/0x1a4 [ 141.614643] ---[ end trace f08b1f47ee3d43ef ]--- And then upon wake, we get [ 144.822647] OOM killer enabled. [ 144.822660] Restarting tasks ... done. [ 144.828624] PM: suspend exit [ 144.854302] [drm:dpu_encoder_frame_done_timeout:2127] [dpu error]enc31 frame done timeout [ 145.153281] rfkill: input handler disabled [ 145.679342] usb 3-1.3: new high-speed USB device number 4 using xhci-hcd [ 145.734319] [drm:dpu_encoder_phys_vid_wait_for_commit_done:513] [dpu error]vblank timeout [ 145.734336] [drm:dpu_kms_wait_for_commit_done:454] [dpu error]wait for commit done returned -110 [ 145.792887] usb 3-1.3: New USB device found, idVendor=5986, idProduct=2115, bcdDevice=54.20 [ 145.792909] usb 3-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 145.792915] usb 3-1.3: Product: Integrated Camera [ 145.792920] usb 3-1.3: Manufacturer: SunplusIT Inc [ 145.822516] [drm:dpu_encoder_helper_report_irq_timeout [msm]] *ERROR* irq timeout id=31, intf=1, pp=0, intr=0 [ 145.870521] usb 3-1.3: can't set config #1, error -71 [ 145.910326] [drm:dpu_encoder_helper_report_irq_timeout [msm]] *ERROR* irq timeout id=31, intf=1, pp=0, intr=0 [ 145.910369] [drm:dpu_encoder_phys_vid_disable [msm]] *ERROR* wait disable failed: id:31 intf:1 ret:-110 [ 145.932329] ldo1: Underflow of regulator enable count [ 145.932343] Failed to disable vdds: -EINVAL [ 145.936885] dsi_link_clk_enable_6g: Failed to enable dsi pixel clk [ 145.936901] msm_dsi_host_power_on: failed to enable link clocks. ret=-22 [ 145.936906] dsi_mgr_bridge_pre_enable: power on host 0 failed, -22 And then a little later... [ 462.153015] ldo1: Underflow of regulator enable count [ 462.153049] Failed to disable vdds: -EINVAL [ 462.155657] Internal error: synchronous external abort: 96000010 [#1] SMP [ 462.155702] Modules linked in: rfcomm xt_conntrack aes_ce_ccm nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack_netlink nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 xfrm_user xfrm_algo nft_counter snd_seq_dummy snd_hrtimer snd_seq snd_seq_device xt_addrtype nft_compat nf_tables libcrc32c nfnetlink br_netfilter bridge stp llc overlay q6asm_dai snd_soc_wsa881x regmap_sdw q6routing q6afe_dai soundwire_qcom snd_soc_wcd934x gpio_wcd934x q6adm snd_soc_wcd_mbhc cpufreq_ondemand cpufreq_conservative q6asm q6dsp_common cpufreq_powersave q6afe algif_hash algif_skcipher q6core af_alg bnep cpufreq_userspace lz4 lz4_compress wcd934x regmap_slimbus zram zsmalloc apr qrtr_smd fastrpc binfmt_misc snd_soc_sdm845 nls_ascii uvcvideo nls_cp437 videobuf2_vmalloc snd_soc_rt5663 vfat videobuf2_memops fat snd_soc_qcom_common snd_soc_rl6231 aes_ce_blk soundwire_bus crypto_simd cryptd aes_ce_cipher pm8941_pwrkey snd_soc_core snd_compress crct10dif_ce ghash_ce gf128mul snd_pcm_dmaengine sha2_ce sha256_arm64 [ 462.156645] qcom_spmi_adc5 snd_pcm sha1_ce qcom_vadc_common qcom_spmi_temp_alarm joydev industrialio snd_timer snd hci_uart soundcore btqca btrtl venus_core btbcm v4l2_mem2mem videobuf2_v4l2 btintel bluetooth videobuf2_common videodev mc ecdh_generic hid_multitouch ecc ath10k_snoc ath10k_core qcom_rng ath mac80211 qcom_q6v5_mss libarc4 cfg80211 rfkill sg qcom_wdt qcom_q6v5_pas evdev slim_qcom_ngd_ctrl qrtr qcom_pil_info pdr_interface qcom_q6v5 slimbus qcom_sysmon rmtfs_mem tcp_bbr sch_fq fuse configfs ip_tables x_tables autofs4 ext4 mbcache jbd2 panel_simple rtc_pm8xxx msm llcc_qcom ocmem ti_sn65dsi86 drm_dp_aux_bus gpu_sched drm_kms_helper drm camcc_sdm845 ipa qcom_common qmi_helpers mdt_loader gpio_keys pwm_bl [ 462.157479] CPU: 1 PID: 961 Comm: gnome-shell Tainted: G W 5.15.6 #45 [ 462.157517] Hardware name: LENOVO 81JL/LNVNB161216, BIOS 9UCN33WW(V2.06) 06/ 4/2019 [ 462.157542] pstate: 804000c5 (Nzcv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 462.157579] pc : dpu_reg_read+0x20/0x30 [msm] [ 462.157870] lr : dpu_hw_intf_get_status+0x2c/0x90 [msm] [ 462.158158] sp : ffff800015f237e0 [ 462.158177] x29: ffff800015f237e0 x28: ffffd0c2fd91cc90 x27: 00000000ffffffff [ 462.158234] x26: ffff2ed907c6c000 x25: 0000000000fe45a8 x24: 0000000000000000 [ 462.158287] x23: ffff2ed90bda9880 x22: 0000000000000003 x21: 000000000000043b [ 462.158339] x20: ffff2ed901483180 x19: ffff800015f2383c x18: ffffffffffffffff [ 462.158393] x17: 000000040044ffff x16: ffffd0c3450b84f0 x15: 0000000000000000 [ 462.158444] x14: 0000000000000000 x13: ffff5e172dc1d000 x12: 000000003474591d [ 462.158496] x11: 0000000000000000 x10: 0000000000000080 x9 : ffffd0c2fd8c3dbc [ 462.158548] x8 : ffff2ed9050fbb00 x7 : ffffd0c3460484c0 x6 : 0000000000000000 [ 462.158598] x5 : 0000000000000000 x4 : 00000000ffffffff x3 : ffffd0c2fd8c3d90 [ 462.158648] x2 : 000000000006a800 x1 : 000000000006a800 x0 : ffff800010f6a800 [ 462.158700] Call trace: [ 462.158720] dpu_reg_read+0x20/0x30 [msm] [ 462.159003] dpu_encoder_phys_vid_get_frame_count+0x74/0xf0 [msm] [ 462.159288] dpu_encoder_get_frame_count+0x38/0x50 [msm] [ 462.159544] dpu_crtc_get_vblank_counter+0x5c/0x8c [msm] [ 462.159592] __get_vblank_counter+0xec/0x140 [drm] [ 462.159709] drm_update_vblank_count+0x70/0x390 [drm] [ 462.159740] drm_vblank_disable_and_save+0x84/0x11c [drm] [ 462.159772] drm_crtc_vblank_off+0x108/0x320 [drm] [ 462.159803] dpu_crtc_disable+0x60/0x3d4 [msm] [ 462.159853] disable_outputs+0x25c/0x320 [drm_kms_helper] [ 462.159893] drm_atomic_helper_commit_modeset_disables+0x28/0x54 [drm_kms_helper] [ 462.159910] msm_atomic_commit_tail+0x1a0/0x780 [msm] [ 462.159959] commit_tail+0xac/0x190 [drm_kms_helper] [ 462.159977] drm_atomic_helper_commit+0x168/0x400 [drm_kms_helper] [ 462.159995] drm_atomic_commit+0x58/0x70 [drm] [ 462.160032] drm_mode_atomic_ioctl+0x864/0xb80 [drm] [ 462.160063] drm_ioctl_kernel+0xd0/0x120 [drm] [ 462.160093] drm_ioctl+0x248/0x470 [drm] [ 462.160124] __arm64_sys_ioctl+0xb4/0xfc [ 462.160136] invoke_syscall+0x50/0x120 [ 462.160148] el0_svc_common.constprop.0+0x4c/0x100 [ 462.160156] do_el0_svc+0x34/0xa0 [ 462.160164] el0_svc+0x28/0x80 [ 462.160174] el0t_64_sync_handler+0xa4/0x130 [ 462.160179] el0t_64_sync+0x1a0/0x1a4 [ 462.160192] Code: d503233f f9400000 8b214041 8b010000 (b9400000) [ 462.160200] ---[ end trace f08b1f47ee3d43f0 ]--- [ 462.195181] usb 3-1.3: USB disconnect, device number 5 [ 483.266267] rcu: INFO: rcu_sched detected stalls on CPUs/tasks: [ 483.266287] rcu: 1-...0: (7 ticks this GP) idle=bfb/1/0x4000000000000000 softirq=18411/18411 fqs=4691 [ 483.266304] (detected by 6, t=21002 jiffies, g=40289, q=8854) [ 483.266313] Task dump for CPU 1: [ 483.266319] task:gmain state:R running task stack: 0 pid: 1562 ppid: 1 flags:0x0000000e [ 483.266336] Call trace: [ 483.266341] __switch_to+0x138/0x190 [ 483.266361] 0x8b007afdbf2f3900 [ 546.283350] rcu: INFO: rcu_sched detected stalls on CPUs/tasks: [ 546.283375] rcu: 1-...0: (7 ticks this GP) idle=bfb/1/0x4000000000000000 softirq=18411/18411 fqs=18763 [ 546.283387] (detected by 0, t=84007 jiffies, g=40289, q=8931) [ 546.283395] Task dump for CPU 1: [ 546.283401] task:gmain state:R running task stack: 0 pid: 1562 ppid: 1 flags:0x0000000e [ 546.283412] Call trace: [ 546.283416] __switch_to+0x138/0x190 [ 546.283433] 0x8b007afdbf2f3900 [ 609.319122] rcu: INFO: rcu_sched detected stalls on CPUs/tasks: [ 609.319145] rcu: 1-...0: (7 ticks this GP) idle=bfb/1/0x4000000000000000 softirq=18411/18411 fqs=32816 [ 609.319162] (detected by 6, t=147012 jiffies, g=40289, q=8968) [ 609.319172] Task dump for CPU 1: [ 609.319177] task:gmain state:R running task stack: 0 pid: 1562 ppid: 1 flags:0x0000000e [ 609.319195] Call trace: [ 609.319200] __switch_to+0x138/0x190 [ 609.319222] 0x8b007afdbf2f3900
On 12/3/21 6:39 PM, Steev Klimaszewski wrote: > > On 12/2/21 9:56 PM, Bjorn Andersson wrote: >> As GDSCs are turned on and off some associated clocks are momentarily >> enabled for house keeping purposes. Failure to enable these clocks seems >> to have been silently ignored in the past, but starting in SM8350 this >> failure will prevent the GDSC to turn on. >> >> At least on SM8350 this operation will enable the RCG per the >> configuration in CFG_REG. This means that the current model where the >> current configuration is written back to CF_REG immediately after >> parking the RCG doesn't work. >> >> Instead, keep track of the currently requested rate of the clock and >> upon enabling the clock reapply the configuration per the saved rate. >> >> Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source >> as needed") >> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> >> --- >> drivers/clk/qcom/clk-rcg.h | 2 ++ >> drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- >> 2 files changed, 19 insertions(+), 15 deletions(-) >> >> <snip patch> > > With this applied, I'm getting > <snip> Actually turns out, I had a testing patch in from Dmitry that I'd never taken back out when it was decided it wasn't good enough. Apologies for the useless message. This does not actually cause the issue, just the combination of them does. Tested on the Lenovo Yoga C630 Tested-By: Steev Klimaszewski <steev@kali.org>
On 02-12-21, 19:56, Bjorn Andersson wrote: > As GDSCs are turned on and off some associated clocks are momentarily > enabled for house keeping purposes. Failure to enable these clocks seems > to have been silently ignored in the past, but starting in SM8350 this > failure will prevent the GDSC to turn on. > > At least on SM8350 this operation will enable the RCG per the > configuration in CFG_REG. This means that the current model where the > current configuration is written back to CF_REG immediately after s/CF_REG/CFG_REG > parking the RCG doesn't work. > > Instead, keep track of the currently requested rate of the clock and > upon enabling the clock reapply the configuration per the saved rate. With that fixed: Reviewed-by: Vinod Koul <vkoul@kernel.org>
On 12/2/21 9:56 PM, Bjorn Andersson wrote: > As GDSCs are turned on and off some associated clocks are momentarily > enabled for house keeping purposes. Failure to enable these clocks seems > to have been silently ignored in the past, but starting in SM8350 this > failure will prevent the GDSC to turn on. > > At least on SM8350 this operation will enable the RCG per the > configuration in CFG_REG. This means that the current model where the > current configuration is written back to CF_REG immediately after > parking the RCG doesn't work. > > Instead, keep track of the currently requested rate of the clock and > upon enabling the clock reapply the configuration per the saved rate. > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > --- > drivers/clk/qcom/clk-rcg.h | 2 ++ > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- > 2 files changed, 19 insertions(+), 15 deletions(-) > > diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h > index 99efcc7f8d88..6939f4e62768 100644 > --- a/drivers/clk/qcom/clk-rcg.h > +++ b/drivers/clk/qcom/clk-rcg.h > @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops; > * @freq_tbl: frequency table > * @clkr: regmap clock handle > * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG > + * @current_rate: cached rate for parked RCGs > */ > struct clk_rcg2 { > u32 cmd_rcgr; > @@ -149,6 +150,7 @@ struct clk_rcg2 { > const struct freq_tbl *freq_tbl; > struct clk_regmap clkr; > u8 cfg_off; > + unsigned long current_rate; > }; > > #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr) > diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c > index e1b1b426fae4..b574b38dcbd5 100644 > --- a/drivers/clk/qcom/clk-rcg2.c > +++ b/drivers/clk/qcom/clk-rcg2.c > @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > { > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask; > + unsigned long rate; > > regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg); > > @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > hid_div = cfg >> CFG_SRC_DIV_SHIFT; > hid_div &= mask; > > - return calc_rate(parent_rate, m, n, mode, hid_div); > + rate = calc_rate(parent_rate, m, n, mode, hid_div); > + if (!rcg->current_rate) > + rcg->current_rate = rate; > + > + return rate; > } > > static int _freq_tbl_determine_rate(struct clk_hw *hw, const struct freq_tbl *f, > @@ -968,12 +973,14 @@ static int clk_rcg2_shared_set_rate(struct clk_hw *hw, unsigned long rate, > if (!f) > return -EINVAL; > > + rcg->current_rate = rate; > + > /* > - * In case clock is disabled, update the CFG, M, N and D registers > - * and don't hit the update bit of CMD register. > + * In the case that the shared RCG is parked, current_rate will be > + * applied as the clock is unparked again, so just return here. > */ > if (!__clk_is_enabled(hw->clk)) > - return __clk_rcg2_configure(rcg, f); > + return 0; > > return clk_rcg2_shared_force_enable_clear(hw, f); > } > @@ -987,8 +994,13 @@ static int clk_rcg2_shared_set_rate_and_parent(struct clk_hw *hw, > static int clk_rcg2_shared_enable(struct clk_hw *hw) > { > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > + const struct freq_tbl *f = NULL; > int ret; > > + f = qcom_find_freq(rcg->freq_tbl, rcg->current_rate); > + if (!f) > + return -EINVAL; > + > /* > * Set the update bit because required configuration has already > * been written in clk_rcg2_shared_set_rate() > @@ -997,7 +1009,7 @@ static int clk_rcg2_shared_enable(struct clk_hw *hw) > if (ret) > return ret; > > - ret = update_config(rcg); > + ret = clk_rcg2_configure(rcg, f); > if (ret) > return ret; > > @@ -1007,13 +1019,6 @@ static int clk_rcg2_shared_enable(struct clk_hw *hw) > static void clk_rcg2_shared_disable(struct clk_hw *hw) > { > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > - u32 cfg; > - > - /* > - * Store current configuration as switching to safe source would clear > - * the SRC and DIV of CFG register > - */ > - regmap_read(rcg->clkr.regmap, rcg->cmd_rcgr + CFG_REG, &cfg); > > /* > * Park the RCG at a safe configuration - sourced off of safe source. > @@ -1031,9 +1036,6 @@ static void clk_rcg2_shared_disable(struct clk_hw *hw) > update_config(rcg); > > clk_rcg2_clear_force_enable(hw); > - > - /* Write back the stored configuration corresponding to current rate */ > - regmap_write(rcg->clkr.regmap, rcg->cmd_rcgr + CFG_REG, cfg); > } > > const struct clk_ops clk_rcg2_shared_ops = { Revisiting this... With Dmitry's patches applied ( https://lore.kernel.org/linux-arm-msm/20211208022210.1300773-1-dmitry.baryshkov@linaro.org/ ) as well as these, and clk_ignore_unused, I get both [ 4.767487] ------------[ cut here ]------------ [ 4.767495] disp_cc_mdss_pclk0_clk_src: rcg didn't update its configuration. and [ 6.449518] ------------[ cut here ]------------ [ 6.449525] video_cc_venus_clk_src: rcg didn't update its configuration. This includes after modifying Dmitry's patches to park the above 2 clocks. Removing "clk_ignore_unused" from the kernel command line, while keeping Dmitry's patchset as well as this patch, results in the disp_cc_mdss_pclk0_clk_src going away, but the video_cc_venus_clk_src still shows up. Applying Dmitry's patches, removing this one, and removing "clk_ignore_unused" from command line arguments ends up with none of these rcg didn't update its configuration messages. As can be seen in http://paste.debian.net/1222931 -- steev
On Thu, 2 Dec 2021 19:56:01 -0800, Bjorn Andersson wrote: > As GDSCs are turned on and off some associated clocks are momentarily > enabled for house keeping purposes. Failure to enable these clocks seems > to have been silently ignored in the past, but starting in SM8350 this > failure will prevent the GDSC to turn on. > > At least on SM8350 this operation will enable the RCG per the > configuration in CFG_REG. This means that the current model where the > current configuration is written back to CF_REG immediately after > parking the RCG doesn't work. > > [...] Applied, thanks! [1/1] clk: qcom: rcg2: Cache rate changes for parked RCGs commit: ce4981ad69145d7444a5cf4fef2e29442aee60dc Best regards,
Quoting Bjorn Andersson (2021-12-02 19:56:01) > As GDSCs are turned on and off some associated clocks are momentarily > enabled for house keeping purposes. Failure to enable these clocks seems > to have been silently ignored in the past, but starting in SM8350 this > failure will prevent the GDSC to turn on. > > At least on SM8350 this operation will enable the RCG per the > configuration in CFG_REG. This means that the current model where the > current configuration is written back to CF_REG immediately after > parking the RCG doesn't work. Just to clarify, is the RCG off and "parked" at XO with the config register dirty and set to the desired frequency and then the RCG is turned on by the GDSC? > > Instead, keep track of the currently requested rate of the clock and > upon enabling the clock reapply the configuration per the saved rate. We already keep track of the requested rate and reapply it on enable, just we're lazy and stash that information in the hardware and not the software. I didn't think the gdsc would be turned on and ruin that all, but it's fair. > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > --- > drivers/clk/qcom/clk-rcg.h | 2 ++ > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- > 2 files changed, 19 insertions(+), 15 deletions(-) > > diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h > index 99efcc7f8d88..6939f4e62768 100644 > --- a/drivers/clk/qcom/clk-rcg.h > +++ b/drivers/clk/qcom/clk-rcg.h > @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops; > * @freq_tbl: frequency table > * @clkr: regmap clock handle > * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG > + * @current_rate: cached rate for parked RCGs > */ > struct clk_rcg2 { > u32 cmd_rcgr; > @@ -149,6 +150,7 @@ struct clk_rcg2 { > const struct freq_tbl *freq_tbl; > struct clk_regmap clkr; > u8 cfg_off; > + unsigned long current_rate; > }; > > #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr) > diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c > index e1b1b426fae4..b574b38dcbd5 100644 > --- a/drivers/clk/qcom/clk-rcg2.c > +++ b/drivers/clk/qcom/clk-rcg2.c > @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > { > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask; > + unsigned long rate; > > regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg); > > @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > hid_div = cfg >> CFG_SRC_DIV_SHIFT; > hid_div &= mask; > > - return calc_rate(parent_rate, m, n, mode, hid_div); > + rate = calc_rate(parent_rate, m, n, mode, hid_div); > + if (!rcg->current_rate) > + rcg->current_rate = rate; Instead of doing this in recalc_rate, all the time, why not make an init clk op that does it once during registration? The other problem I see is that the rate we calculate may be wrong if the parent is registered after this clk. I think this came up originally when the patch this is fixing was discussed. So instead of saving the current_rate can we save the cfg register value (or however many registers we need) to put back the frequency of the clk to what we want on enable? The other thing is that we made recalc_rate() work "seamlessly" here by stashing the frequency into the register but leaving it uncommitted until enable. We may need to now look at the software copy of the registers in the shared rcg recalc rate operation to figure out what the frequency is. > + > + return rate; > } > > static int _freq_tbl_determine_rate(struct clk_hw *hw, const struct freq_tbl *f, > @@ -968,12 +973,14 @@ static int clk_rcg2_shared_set_rate(struct clk_hw *hw, unsigned long rate, > if (!f) > return -EINVAL; > > + rcg->current_rate = rate; > + > /* > - * In case clock is disabled, update the CFG, M, N and D registers > - * and don't hit the update bit of CMD register. > + * In the case that the shared RCG is parked, current_rate will be > + * applied as the clock is unparked again, so just return here. > */ > if (!__clk_is_enabled(hw->clk)) > - return __clk_rcg2_configure(rcg, f); > + return 0; > > return clk_rcg2_shared_force_enable_clear(hw, f); > } > @@ -987,8 +994,13 @@ static int clk_rcg2_shared_set_rate_and_parent(struct clk_hw *hw, > static int clk_rcg2_shared_enable(struct clk_hw *hw) > { > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > + const struct freq_tbl *f = NULL; Do not assign a value to a variable > int ret; > > + f = qcom_find_freq(rcg->freq_tbl, rcg->current_rate); and then assign it again without testing it before. > + if (!f) > + return -EINVAL; > + > /* > * Set the update bit because required configuration has already
On Wed 15 Dec 17:51 PST 2021, Stephen Boyd wrote: > Quoting Bjorn Andersson (2021-12-02 19:56:01) > > As GDSCs are turned on and off some associated clocks are momentarily > > enabled for house keeping purposes. Failure to enable these clocks seems > > to have been silently ignored in the past, but starting in SM8350 this > > failure will prevent the GDSC to turn on. > > > > At least on SM8350 this operation will enable the RCG per the > > configuration in CFG_REG. This means that the current model where the > > current configuration is written back to CF_REG immediately after > > parking the RCG doesn't work. > > Just to clarify, is the RCG off and "parked" at XO with the config > register dirty and set to the desired frequency and then the RCG is > turned on by the GDSC? > Correct, that's exactly what I'm observing. > > > > Instead, keep track of the currently requested rate of the clock and > > upon enabling the clock reapply the configuration per the saved rate. > > We already keep track of the requested rate and reapply it on enable, > just we're lazy and stash that information in the hardware and not the > software. I didn't think the gdsc would be turned on and ruin that all, > but it's fair. > Up until SM8350 I see no evidence that this has been a problem, but now it is. So there's likely some changes in the hardware there... > > > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > > --- > > drivers/clk/qcom/clk-rcg.h | 2 ++ > > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- > > 2 files changed, 19 insertions(+), 15 deletions(-) > > > > diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h > > index 99efcc7f8d88..6939f4e62768 100644 > > --- a/drivers/clk/qcom/clk-rcg.h > > +++ b/drivers/clk/qcom/clk-rcg.h > > @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops; > > * @freq_tbl: frequency table > > * @clkr: regmap clock handle > > * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG > > + * @current_rate: cached rate for parked RCGs > > */ > > struct clk_rcg2 { > > u32 cmd_rcgr; > > @@ -149,6 +150,7 @@ struct clk_rcg2 { > > const struct freq_tbl *freq_tbl; > > struct clk_regmap clkr; > > u8 cfg_off; > > + unsigned long current_rate; > > }; > > > > #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr) > > diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c > > index e1b1b426fae4..b574b38dcbd5 100644 > > --- a/drivers/clk/qcom/clk-rcg2.c > > +++ b/drivers/clk/qcom/clk-rcg2.c > > @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > { > > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > > u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask; > > + unsigned long rate; > > > > regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg); > > > > @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > hid_div = cfg >> CFG_SRC_DIV_SHIFT; > > hid_div &= mask; > > > > - return calc_rate(parent_rate, m, n, mode, hid_div); > > + rate = calc_rate(parent_rate, m, n, mode, hid_div); > > + if (!rcg->current_rate) > > + rcg->current_rate = rate; > > Instead of doing this in recalc_rate, all the time, why not make an init > clk op that does it once during registration? The other problem I see is > that the rate we calculate may be wrong if the parent is registered > after this clk. I think this came up originally when the patch this is > fixing was discussed. > I would need to go back and reproduce the issue I saw, but I had to add this because I ended up in clk_rcg2_shared_enable() with current_rate = 0, which I think would be equally bad to just committing the dirty configuration. > So instead of saving the current_rate can we save the cfg register value > (or however many registers we need) to put back the frequency of the clk > to what we want on enable? The other thing is that we made recalc_rate() > work "seamlessly" here by stashing the frequency into the register but > leaving it uncommitted until enable. We may need to now look at the > software copy of the registers in the shared rcg recalc rate operation > to figure out what the frequency is. > I made an attempt at this, the problem I had was to come up within something sane for how to deal with set_rate on parked clocks; because we need to re-generate the register contents, without writing out the value - and that got messy. So stashing the frequency turned out to be much cleaner. I believe that this is also what they do downstream... Regards, Bjorn
Quoting Bjorn Andersson (2021-12-15 18:48:27) > On Wed 15 Dec 17:51 PST 2021, Stephen Boyd wrote: > > > Quoting Bjorn Andersson (2021-12-02 19:56:01) > > > As GDSCs are turned on and off some associated clocks are momentarily > > > enabled for house keeping purposes. Failure to enable these clocks seems > > > to have been silently ignored in the past, but starting in SM8350 this > > > failure will prevent the GDSC to turn on. > > > > > > At least on SM8350 this operation will enable the RCG per the > > > configuration in CFG_REG. This means that the current model where the > > > current configuration is written back to CF_REG immediately after > > > parking the RCG doesn't work. > > > > Just to clarify, is the RCG off and "parked" at XO with the config > > register dirty and set to the desired frequency and then the RCG is > > turned on by the GDSC? > > > > Correct, that's exactly what I'm observing. Cool can you add that detail to the commit message? > > > > > > > Instead, keep track of the currently requested rate of the clock and > > > upon enabling the clock reapply the configuration per the saved rate. > > > > We already keep track of the requested rate and reapply it on enable, > > just we're lazy and stash that information in the hardware and not the > > software. I didn't think the gdsc would be turned on and ruin that all, > > but it's fair. > > > > Up until SM8350 I see no evidence that this has been a problem, but now > it is. So there's likely some changes in the hardware there... > > > > > > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") > > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > > > --- > > > drivers/clk/qcom/clk-rcg.h | 2 ++ > > > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- > > > 2 files changed, 19 insertions(+), 15 deletions(-) > > > > > > diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h > > > index 99efcc7f8d88..6939f4e62768 100644 > > > --- a/drivers/clk/qcom/clk-rcg.h > > > +++ b/drivers/clk/qcom/clk-rcg.h > > > @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops; > > > * @freq_tbl: frequency table > > > * @clkr: regmap clock handle > > > * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG > > > + * @current_rate: cached rate for parked RCGs > > > */ > > > struct clk_rcg2 { > > > u32 cmd_rcgr; > > > @@ -149,6 +150,7 @@ struct clk_rcg2 { > > > const struct freq_tbl *freq_tbl; > > > struct clk_regmap clkr; > > > u8 cfg_off; > > > + unsigned long current_rate; > > > }; > > > > > > #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr) > > > diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c > > > index e1b1b426fae4..b574b38dcbd5 100644 > > > --- a/drivers/clk/qcom/clk-rcg2.c > > > +++ b/drivers/clk/qcom/clk-rcg2.c > > > @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > > { > > > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > > > u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask; > > > + unsigned long rate; > > > > > > regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg); > > > > > > @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > > hid_div = cfg >> CFG_SRC_DIV_SHIFT; > > > hid_div &= mask; > > > > > > - return calc_rate(parent_rate, m, n, mode, hid_div); > > > + rate = calc_rate(parent_rate, m, n, mode, hid_div); > > > + if (!rcg->current_rate) > > > + rcg->current_rate = rate; > > > > Instead of doing this in recalc_rate, all the time, why not make an init > > clk op that does it once during registration? The other problem I see is > > that the rate we calculate may be wrong if the parent is registered > > after this clk. I think this came up originally when the patch this is > > fixing was discussed. > > > > I would need to go back and reproduce the issue I saw, but I had to add > this because I ended up in clk_rcg2_shared_enable() with current_rate = > 0, which I think would be equally bad to just committing the dirty > configuration. Alright. > > > So instead of saving the current_rate can we save the cfg register value > > (or however many registers we need) to put back the frequency of the clk > > to what we want on enable? The other thing is that we made recalc_rate() > > work "seamlessly" here by stashing the frequency into the register but > > leaving it uncommitted until enable. We may need to now look at the > > software copy of the registers in the shared rcg recalc rate operation > > to figure out what the frequency is. > > > > I made an attempt at this, the problem I had was to come up within > something sane for how to deal with set_rate on parked clocks; because > we need to re-generate the register contents, without writing out the > value - and that got messy. Looking back on the introduction of this code[1] I see that it's not about the rate but more about the parent. i.e. we park the clk on the XO parent but don't care about the m/n values or pre divider because it doesn't really matter if the clk is running slowly. So nothing needs to be saved except for the cfg register, and we can do that in software with a single u32 instead of using a rate and looking it up and then reprogramming the other values. We should be able to cache the register content with an init clk_op. > > So stashing the frequency turned out to be much cleaner. I believe that > this is also what they do downstream... > Downstream doing something isn't a great reason. [1] https://lore.kernel.org/r/07dbf890975c1178bc4cc2360c25526a@codeaurora.org
On Thu 16 Dec 10:58 PST 2021, Stephen Boyd wrote: > Quoting Bjorn Andersson (2021-12-15 18:48:27) > > On Wed 15 Dec 17:51 PST 2021, Stephen Boyd wrote: > > > > > Quoting Bjorn Andersson (2021-12-02 19:56:01) > > > > As GDSCs are turned on and off some associated clocks are momentarily > > > > enabled for house keeping purposes. Failure to enable these clocks seems > > > > to have been silently ignored in the past, but starting in SM8350 this > > > > failure will prevent the GDSC to turn on. > > > > > > > > At least on SM8350 this operation will enable the RCG per the > > > > configuration in CFG_REG. This means that the current model where the > > > > current configuration is written back to CF_REG immediately after > > > > parking the RCG doesn't work. > > > > > > Just to clarify, is the RCG off and "parked" at XO with the config > > > register dirty and set to the desired frequency and then the RCG is > > > turned on by the GDSC? > > > > > > > Correct, that's exactly what I'm observing. > > Cool can you add that detail to the commit message? > Sure. > > > > > > > > > > Instead, keep track of the currently requested rate of the clock and > > > > upon enabling the clock reapply the configuration per the saved rate. > > > > > > We already keep track of the requested rate and reapply it on enable, > > > just we're lazy and stash that information in the hardware and not the > > > software. I didn't think the gdsc would be turned on and ruin that all, > > > but it's fair. > > > > > > > Up until SM8350 I see no evidence that this has been a problem, but now > > it is. So there's likely some changes in the hardware there... > > > > > > > > > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") > > > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > > > > --- > > > > drivers/clk/qcom/clk-rcg.h | 2 ++ > > > > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- > > > > 2 files changed, 19 insertions(+), 15 deletions(-) > > > > > > > > diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h > > > > index 99efcc7f8d88..6939f4e62768 100644 > > > > --- a/drivers/clk/qcom/clk-rcg.h > > > > +++ b/drivers/clk/qcom/clk-rcg.h > > > > @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops; > > > > * @freq_tbl: frequency table > > > > * @clkr: regmap clock handle > > > > * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG > > > > + * @current_rate: cached rate for parked RCGs > > > > */ > > > > struct clk_rcg2 { > > > > u32 cmd_rcgr; > > > > @@ -149,6 +150,7 @@ struct clk_rcg2 { > > > > const struct freq_tbl *freq_tbl; > > > > struct clk_regmap clkr; > > > > u8 cfg_off; > > > > + unsigned long current_rate; > > > > }; > > > > > > > > #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr) > > > > diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c > > > > index e1b1b426fae4..b574b38dcbd5 100644 > > > > --- a/drivers/clk/qcom/clk-rcg2.c > > > > +++ b/drivers/clk/qcom/clk-rcg2.c > > > > @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > > > { > > > > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > > > > u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask; > > > > + unsigned long rate; > > > > > > > > regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg); > > > > > > > > @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > > > hid_div = cfg >> CFG_SRC_DIV_SHIFT; > > > > hid_div &= mask; > > > > > > > > - return calc_rate(parent_rate, m, n, mode, hid_div); > > > > + rate = calc_rate(parent_rate, m, n, mode, hid_div); > > > > + if (!rcg->current_rate) > > > > + rcg->current_rate = rate; > > > > > > Instead of doing this in recalc_rate, all the time, why not make an init > > > clk op that does it once during registration? The other problem I see is > > > that the rate we calculate may be wrong if the parent is registered > > > after this clk. I think this came up originally when the patch this is > > > fixing was discussed. > > > > > > > I would need to go back and reproduce the issue I saw, but I had to add > > this because I ended up in clk_rcg2_shared_enable() with current_rate = > > 0, which I think would be equally bad to just committing the dirty > > configuration. > > Alright. > > > > > > So instead of saving the current_rate can we save the cfg register value > > > (or however many registers we need) to put back the frequency of the clk > > > to what we want on enable? The other thing is that we made recalc_rate() > > > work "seamlessly" here by stashing the frequency into the register but > > > leaving it uncommitted until enable. We may need to now look at the > > > software copy of the registers in the shared rcg recalc rate operation > > > to figure out what the frequency is. > > > > > > > I made an attempt at this, the problem I had was to come up within > > something sane for how to deal with set_rate on parked clocks; because > > we need to re-generate the register contents, without writing out the > > value - and that got messy. > > Looking back on the introduction of this code[1] I see that it's not > about the rate but more about the parent. i.e. we park the clk on the XO > parent but don't care about the m/n values or pre divider because it > doesn't really matter if the clk is running slowly. So nothing needs to > be saved except for the cfg register, and we can do that in software > with a single u32 instead of using a rate and looking it up and then > reprogramming the other values. We should be able to cache the register > content with an init clk_op. > So you're suggesting that, in clk_rcg2_shared_set_rate(), when the RCG is found to be disabled, I should write out M, N, D and calculate a new cfg value which I stash until the next enable? Looks a little bit messy, but I will give it a try. > > > > So stashing the frequency turned out to be much cleaner. I believe that > > this is also what they do downstream... > > > > Downstream doing something isn't a great reason. > :) > [1] https://lore.kernel.org/r/07dbf890975c1178bc4cc2360c25526a@codeaurora.org Regards, Bjorn
Quoting Bjorn Andersson (2021-12-16 15:32:32) > On Thu 16 Dec 10:58 PST 2021, Stephen Boyd wrote: > > > Quoting Bjorn Andersson (2021-12-15 18:48:27) > > > On Wed 15 Dec 17:51 PST 2021, Stephen Boyd wrote: > > > > > > > Quoting Bjorn Andersson (2021-12-02 19:56:01) > > > > > As GDSCs are turned on and off some associated clocks are momentarily > > > > > enabled for house keeping purposes. Failure to enable these clocks seems > > > > > to have been silently ignored in the past, but starting in SM8350 this > > > > > failure will prevent the GDSC to turn on. > > > > > > > > > > At least on SM8350 this operation will enable the RCG per the > > > > > configuration in CFG_REG. This means that the current model where the > > > > > current configuration is written back to CF_REG immediately after > > > > > parking the RCG doesn't work. > > > > > > > > Just to clarify, is the RCG off and "parked" at XO with the config > > > > register dirty and set to the desired frequency and then the RCG is > > > > turned on by the GDSC? > > > > > > > > > > Correct, that's exactly what I'm observing. > > > > Cool can you add that detail to the commit message? > > > > Sure. > > > > > > > > > > > > > > Instead, keep track of the currently requested rate of the clock and > > > > > upon enabling the clock reapply the configuration per the saved rate. > > > > > > > > We already keep track of the requested rate and reapply it on enable, > > > > just we're lazy and stash that information in the hardware and not the > > > > software. I didn't think the gdsc would be turned on and ruin that all, > > > > but it's fair. > > > > > > > > > > Up until SM8350 I see no evidence that this has been a problem, but now > > > it is. So there's likely some changes in the hardware there... > > > > > > > > > > > > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") > > > > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > > > > > --- > > > > > drivers/clk/qcom/clk-rcg.h | 2 ++ > > > > > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- > > > > > 2 files changed, 19 insertions(+), 15 deletions(-) > > > > > > > > > > diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h > > > > > index 99efcc7f8d88..6939f4e62768 100644 > > > > > --- a/drivers/clk/qcom/clk-rcg.h > > > > > +++ b/drivers/clk/qcom/clk-rcg.h > > > > > @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops; > > > > > * @freq_tbl: frequency table > > > > > * @clkr: regmap clock handle > > > > > * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG > > > > > + * @current_rate: cached rate for parked RCGs > > > > > */ > > > > > struct clk_rcg2 { > > > > > u32 cmd_rcgr; > > > > > @@ -149,6 +150,7 @@ struct clk_rcg2 { > > > > > const struct freq_tbl *freq_tbl; > > > > > struct clk_regmap clkr; > > > > > u8 cfg_off; > > > > > + unsigned long current_rate; > > > > > }; > > > > > > > > > > #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr) > > > > > diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c > > > > > index e1b1b426fae4..b574b38dcbd5 100644 > > > > > --- a/drivers/clk/qcom/clk-rcg2.c > > > > > +++ b/drivers/clk/qcom/clk-rcg2.c > > > > > @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > > > > { > > > > > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > > > > > u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask; > > > > > + unsigned long rate; > > > > > > > > > > regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg); > > > > > > > > > > @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > > > > hid_div = cfg >> CFG_SRC_DIV_SHIFT; > > > > > hid_div &= mask; > > > > > > > > > > - return calc_rate(parent_rate, m, n, mode, hid_div); > > > > > + rate = calc_rate(parent_rate, m, n, mode, hid_div); > > > > > + if (!rcg->current_rate) > > > > > + rcg->current_rate = rate; > > > > > > > > Instead of doing this in recalc_rate, all the time, why not make an init > > > > clk op that does it once during registration? The other problem I see is > > > > that the rate we calculate may be wrong if the parent is registered > > > > after this clk. I think this came up originally when the patch this is > > > > fixing was discussed. > > > > > > > > > > I would need to go back and reproduce the issue I saw, but I had to add > > > this because I ended up in clk_rcg2_shared_enable() with current_rate = > > > 0, which I think would be equally bad to just committing the dirty > > > configuration. > > > > Alright. > > > > > > > > > So instead of saving the current_rate can we save the cfg register value > > > > (or however many registers we need) to put back the frequency of the clk > > > > to what we want on enable? The other thing is that we made recalc_rate() > > > > work "seamlessly" here by stashing the frequency into the register but > > > > leaving it uncommitted until enable. We may need to now look at the > > > > software copy of the registers in the shared rcg recalc rate operation > > > > to figure out what the frequency is. > > > > > > > > > > I made an attempt at this, the problem I had was to come up within > > > something sane for how to deal with set_rate on parked clocks; because > > > we need to re-generate the register contents, without writing out the > > > value - and that got messy. > > > > Looking back on the introduction of this code[1] I see that it's not > > about the rate but more about the parent. i.e. we park the clk on the XO > > parent but don't care about the m/n values or pre divider because it > > doesn't really matter if the clk is running slowly. So nothing needs to > > be saved except for the cfg register, and we can do that in software > > with a single u32 instead of using a rate and looking it up and then > > reprogramming the other values. We should be able to cache the register > > content with an init clk_op. > > > > So you're suggesting that, in clk_rcg2_shared_set_rate(), when the RCG > is found to be disabled, I should write out M, N, D and calculate a new > cfg value which I stash until the next enable? > > Looks a little bit messy, but I will give it a try. No. I don't see where clk_rcg2_shared_set_rate() needs to change. I'm suggesting we cache the config register on disable so it can be restored on enable. Basically everything is the same except now we don't write the cfg register and leave it dirty in the hardware. We need a shared rcg version of recalc rate that looks at the shadow cfg register instead of reading the hardware because we've changed the parent behind the back of the framework and we want to make it look like nothing has changed. This is all based on my understanding that the problem is the RCG is changing rate due to the gdsc turning on the clk for us. So we can't leave anything dirty in the hardware and have to keep it in software. I hope the change is minimal.
On Thu 16 Dec 19:45 CST 2021, Stephen Boyd wrote: > Quoting Bjorn Andersson (2021-12-16 15:32:32) > > On Thu 16 Dec 10:58 PST 2021, Stephen Boyd wrote: > > > > > Quoting Bjorn Andersson (2021-12-15 18:48:27) > > > > On Wed 15 Dec 17:51 PST 2021, Stephen Boyd wrote: > > > > > > > > > Quoting Bjorn Andersson (2021-12-02 19:56:01) > > > > > > As GDSCs are turned on and off some associated clocks are momentarily > > > > > > enabled for house keeping purposes. Failure to enable these clocks seems > > > > > > to have been silently ignored in the past, but starting in SM8350 this > > > > > > failure will prevent the GDSC to turn on. > > > > > > > > > > > > At least on SM8350 this operation will enable the RCG per the > > > > > > configuration in CFG_REG. This means that the current model where the > > > > > > current configuration is written back to CF_REG immediately after > > > > > > parking the RCG doesn't work. > > > > > > > > > > Just to clarify, is the RCG off and "parked" at XO with the config > > > > > register dirty and set to the desired frequency and then the RCG is > > > > > turned on by the GDSC? > > > > > > > > > > > > > Correct, that's exactly what I'm observing. > > > > > > Cool can you add that detail to the commit message? > > > > > > > Sure. > > > > > > > > > > > > > > > > > > Instead, keep track of the currently requested rate of the clock and > > > > > > upon enabling the clock reapply the configuration per the saved rate. > > > > > > > > > > We already keep track of the requested rate and reapply it on enable, > > > > > just we're lazy and stash that information in the hardware and not the > > > > > software. I didn't think the gdsc would be turned on and ruin that all, > > > > > but it's fair. > > > > > > > > > > > > > Up until SM8350 I see no evidence that this has been a problem, but now > > > > it is. So there's likely some changes in the hardware there... > > > > > > > > > > > > > > > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") > > > > > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> > > > > > > --- > > > > > > drivers/clk/qcom/clk-rcg.h | 2 ++ > > > > > > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- > > > > > > 2 files changed, 19 insertions(+), 15 deletions(-) > > > > > > > > > > > > diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h > > > > > > index 99efcc7f8d88..6939f4e62768 100644 > > > > > > --- a/drivers/clk/qcom/clk-rcg.h > > > > > > +++ b/drivers/clk/qcom/clk-rcg.h > > > > > > @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops; > > > > > > * @freq_tbl: frequency table > > > > > > * @clkr: regmap clock handle > > > > > > * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG > > > > > > + * @current_rate: cached rate for parked RCGs > > > > > > */ > > > > > > struct clk_rcg2 { > > > > > > u32 cmd_rcgr; > > > > > > @@ -149,6 +150,7 @@ struct clk_rcg2 { > > > > > > const struct freq_tbl *freq_tbl; > > > > > > struct clk_regmap clkr; > > > > > > u8 cfg_off; > > > > > > + unsigned long current_rate; > > > > > > }; > > > > > > > > > > > > #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr) > > > > > > diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c > > > > > > index e1b1b426fae4..b574b38dcbd5 100644 > > > > > > --- a/drivers/clk/qcom/clk-rcg2.c > > > > > > +++ b/drivers/clk/qcom/clk-rcg2.c > > > > > > @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > > > > > { > > > > > > struct clk_rcg2 *rcg = to_clk_rcg2(hw); > > > > > > u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask; > > > > > > + unsigned long rate; > > > > > > > > > > > > regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg); > > > > > > > > > > > > @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) > > > > > > hid_div = cfg >> CFG_SRC_DIV_SHIFT; > > > > > > hid_div &= mask; > > > > > > > > > > > > - return calc_rate(parent_rate, m, n, mode, hid_div); > > > > > > + rate = calc_rate(parent_rate, m, n, mode, hid_div); > > > > > > + if (!rcg->current_rate) > > > > > > + rcg->current_rate = rate; > > > > > > > > > > Instead of doing this in recalc_rate, all the time, why not make an init > > > > > clk op that does it once during registration? The other problem I see is > > > > > that the rate we calculate may be wrong if the parent is registered > > > > > after this clk. I think this came up originally when the patch this is > > > > > fixing was discussed. > > > > > > > > > > > > > I would need to go back and reproduce the issue I saw, but I had to add > > > > this because I ended up in clk_rcg2_shared_enable() with current_rate = > > > > 0, which I think would be equally bad to just committing the dirty > > > > configuration. > > > > > > Alright. > > > > > > > > > > > > So instead of saving the current_rate can we save the cfg register value > > > > > (or however many registers we need) to put back the frequency of the clk > > > > > to what we want on enable? The other thing is that we made recalc_rate() > > > > > work "seamlessly" here by stashing the frequency into the register but > > > > > leaving it uncommitted until enable. We may need to now look at the > > > > > software copy of the registers in the shared rcg recalc rate operation > > > > > to figure out what the frequency is. > > > > > > > > > > > > > I made an attempt at this, the problem I had was to come up within > > > > something sane for how to deal with set_rate on parked clocks; because > > > > we need to re-generate the register contents, without writing out the > > > > value - and that got messy. > > > > > > Looking back on the introduction of this code[1] I see that it's not > > > about the rate but more about the parent. i.e. we park the clk on the XO > > > parent but don't care about the m/n values or pre divider because it > > > doesn't really matter if the clk is running slowly. So nothing needs to > > > be saved except for the cfg register, and we can do that in software > > > with a single u32 instead of using a rate and looking it up and then > > > reprogramming the other values. We should be able to cache the register > > > content with an init clk_op. > > > > > > > So you're suggesting that, in clk_rcg2_shared_set_rate(), when the RCG > > is found to be disabled, I should write out M, N, D and calculate a new > > cfg value which I stash until the next enable? > > > > Looks a little bit messy, but I will give it a try. > > No. I don't see where clk_rcg2_shared_set_rate() needs to change. > > I'm suggesting we cache the config register on disable so it can be > restored on enable. Basically everything is the same except now we don't > write the cfg register and leave it dirty in the hardware. We need a > shared rcg version of recalc rate that looks at the shadow cfg register > instead of reading the hardware because we've changed the parent behind > the back of the framework and we want to make it look like nothing has > changed. > I see, that was my first attempt of an implementation as well. The problem I ran into right away was that i had something that did disable(), set_rate(), enable() and I would restore the wrong settings. So clk_rcg2_shared_set_rate() needs to update the stashed cfg value - and it needs to write out M, N and D if we're not caching those. > This is all based on my understanding that the problem is the RCG is > changing rate due to the gdsc turning on the clk for us. So we can't > leave anything dirty in the hardware and have to keep it in software. > I hope the change is minimal. That's my understanding as well. Looking more at the code I think it's possible that we get disable(), set_parent(), enable() as well; which if that's the case would result in the same problem, so I assume I need to tend to that as well. Regards, Bjorn
Quoting Bjorn Andersson (2021-12-16 20:05:52) > On Thu 16 Dec 19:45 CST 2021, Stephen Boyd wrote: > > > > > > > > > > > > > > > So instead of saving the current_rate can we save the cfg register value > > > > > > (or however many registers we need) to put back the frequency of the clk > > > > > > to what we want on enable? The other thing is that we made recalc_rate() > > > > > > work "seamlessly" here by stashing the frequency into the register but > > > > > > leaving it uncommitted until enable. We may need to now look at the > > > > > > software copy of the registers in the shared rcg recalc rate operation > > > > > > to figure out what the frequency is. > > > > > > > > > > > > > > > > I made an attempt at this, the problem I had was to come up within > > > > > something sane for how to deal with set_rate on parked clocks; because > > > > > we need to re-generate the register contents, without writing out the > > > > > value - and that got messy. > > > > > > > > Looking back on the introduction of this code[1] I see that it's not > > > > about the rate but more about the parent. i.e. we park the clk on the XO > > > > parent but don't care about the m/n values or pre divider because it > > > > doesn't really matter if the clk is running slowly. So nothing needs to > > > > be saved except for the cfg register, and we can do that in software > > > > with a single u32 instead of using a rate and looking it up and then > > > > reprogramming the other values. We should be able to cache the register > > > > content with an init clk_op. > > > > > > > > > > So you're suggesting that, in clk_rcg2_shared_set_rate(), when the RCG > > > is found to be disabled, I should write out M, N, D and calculate a new > > > cfg value which I stash until the next enable? > > > > > > Looks a little bit messy, but I will give it a try. > > > > No. I don't see where clk_rcg2_shared_set_rate() needs to change. > > > > I'm suggesting we cache the config register on disable so it can be > > restored on enable. Basically everything is the same except now we don't > > write the cfg register and leave it dirty in the hardware. We need a > > shared rcg version of recalc rate that looks at the shadow cfg register > > instead of reading the hardware because we've changed the parent behind > > the back of the framework and we want to make it look like nothing has > > changed. > > > > I see, that was my first attempt of an implementation as well. > > The problem I ran into right away was that i had something that did > disable(), set_rate(), enable() and I would restore the wrong settings. > > So clk_rcg2_shared_set_rate() needs to update the stashed cfg value - > and it needs to write out M, N and D if we're not caching those. > > > This is all based on my understanding that the problem is the RCG is > > changing rate due to the gdsc turning on the clk for us. So we can't > > leave anything dirty in the hardware and have to keep it in software. > > I hope the change is minimal. > > That's my understanding as well. > > > Looking more at the code I think it's possible that we get disable(), > set_parent(), enable() as well; which if that's the case would result > in the same problem, so I assume I need to tend to that as well. Hopefully we can write the M, N, D and pre-divier values all the time and avoid writing the parent selection register (the cfg one) when the clk is off. It would mean that the "safe parent" of XO is getting divided pretty heavily sometimes but I suspect it doesn't matter in practice. When the clk is enabled in the kernel, we'll move the parent over by making the cfg register have the right parent selectoin and then the mnd and divider would already be what they're supposed to be in the hardware. Does that work?
diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h index 99efcc7f8d88..6939f4e62768 100644 --- a/drivers/clk/qcom/clk-rcg.h +++ b/drivers/clk/qcom/clk-rcg.h @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops; * @freq_tbl: frequency table * @clkr: regmap clock handle * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG + * @current_rate: cached rate for parked RCGs */ struct clk_rcg2 { u32 cmd_rcgr; @@ -149,6 +150,7 @@ struct clk_rcg2 { const struct freq_tbl *freq_tbl; struct clk_regmap clkr; u8 cfg_off; + unsigned long current_rate; }; #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr) diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c index e1b1b426fae4..b574b38dcbd5 100644 --- a/drivers/clk/qcom/clk-rcg2.c +++ b/drivers/clk/qcom/clk-rcg2.c @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) { struct clk_rcg2 *rcg = to_clk_rcg2(hw); u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask; + unsigned long rate; regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg); @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate) hid_div = cfg >> CFG_SRC_DIV_SHIFT; hid_div &= mask; - return calc_rate(parent_rate, m, n, mode, hid_div); + rate = calc_rate(parent_rate, m, n, mode, hid_div); + if (!rcg->current_rate) + rcg->current_rate = rate; + + return rate; } static int _freq_tbl_determine_rate(struct clk_hw *hw, const struct freq_tbl *f, @@ -968,12 +973,14 @@ static int clk_rcg2_shared_set_rate(struct clk_hw *hw, unsigned long rate, if (!f) return -EINVAL; + rcg->current_rate = rate; + /* - * In case clock is disabled, update the CFG, M, N and D registers - * and don't hit the update bit of CMD register. + * In the case that the shared RCG is parked, current_rate will be + * applied as the clock is unparked again, so just return here. */ if (!__clk_is_enabled(hw->clk)) - return __clk_rcg2_configure(rcg, f); + return 0; return clk_rcg2_shared_force_enable_clear(hw, f); } @@ -987,8 +994,13 @@ static int clk_rcg2_shared_set_rate_and_parent(struct clk_hw *hw, static int clk_rcg2_shared_enable(struct clk_hw *hw) { struct clk_rcg2 *rcg = to_clk_rcg2(hw); + const struct freq_tbl *f = NULL; int ret; + f = qcom_find_freq(rcg->freq_tbl, rcg->current_rate); + if (!f) + return -EINVAL; + /* * Set the update bit because required configuration has already * been written in clk_rcg2_shared_set_rate() @@ -997,7 +1009,7 @@ static int clk_rcg2_shared_enable(struct clk_hw *hw) if (ret) return ret; - ret = update_config(rcg); + ret = clk_rcg2_configure(rcg, f); if (ret) return ret; @@ -1007,13 +1019,6 @@ static int clk_rcg2_shared_enable(struct clk_hw *hw) static void clk_rcg2_shared_disable(struct clk_hw *hw) { struct clk_rcg2 *rcg = to_clk_rcg2(hw); - u32 cfg; - - /* - * Store current configuration as switching to safe source would clear - * the SRC and DIV of CFG register - */ - regmap_read(rcg->clkr.regmap, rcg->cmd_rcgr + CFG_REG, &cfg); /* * Park the RCG at a safe configuration - sourced off of safe source. @@ -1031,9 +1036,6 @@ static void clk_rcg2_shared_disable(struct clk_hw *hw) update_config(rcg); clk_rcg2_clear_force_enable(hw); - - /* Write back the stored configuration corresponding to current rate */ - regmap_write(rcg->clkr.regmap, rcg->cmd_rcgr + CFG_REG, cfg); } const struct clk_ops clk_rcg2_shared_ops = {
As GDSCs are turned on and off some associated clocks are momentarily enabled for house keeping purposes. Failure to enable these clocks seems to have been silently ignored in the past, but starting in SM8350 this failure will prevent the GDSC to turn on. At least on SM8350 this operation will enable the RCG per the configuration in CFG_REG. This means that the current model where the current configuration is written back to CF_REG immediately after parking the RCG doesn't work. Instead, keep track of the currently requested rate of the clock and upon enabling the clock reapply the configuration per the saved rate. Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> --- drivers/clk/qcom/clk-rcg.h | 2 ++ drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++--------------- 2 files changed, 19 insertions(+), 15 deletions(-)