| Message ID | 20220307154558.2505734-2-robert.foss@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Revert vendor property from anx7625 bindings | expand |
On Mon, 7 Mar 2022 at 16:46, Robert Foss <robert.foss@linaro.org> wrote: > > This reverts commit a43661e7e819b100e1f833a35018560a1d9abb39. > --- > .../display/bridge/analogix,anx7625.yaml | 65 +------------------ > 1 file changed, 2 insertions(+), 63 deletions(-) > > diff --git a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > index 1d3e88daca041..ab48ab2f4240d 100644 > --- a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > +++ b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > @@ -43,70 +43,14 @@ properties: > vdd33-supply: > description: Regulator that provides the supply 3.3V power. > > - analogix,lane0-swing: > - $ref: /schemas/types.yaml#/definitions/uint8-array > - minItems: 1 > - maxItems: 20 > - description: > - an array of swing register setting for DP tx lane0 PHY. > - Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > - Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and > - [Swing control] setting. > - Registers 0~9, bit 3:0 is [Boost control], these bits control > - post cursor manual, increase the [Boost control] to increase > - Pre-emphasis value. > - Registers 0~9, bit 6:4 is [Swing control], these bits control > - swing manual, increase [Swing control] setting to add Vp-p value > - for each Swing, Pre. > - Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > - Swing1_Pre2, Swing0_Pre3, they are for [R select control] and > - [R Termination control] setting. > - Registers 10~19, bit 4:0 is [R select control], these bits are > - compensation manual, increase it can enhance IO driven strength > - and Vp-p. > - Registers 10~19, bit 5:6 is [R termination control], these bits > - adjust 50ohm impedance of DP tx termination. 00:55 ohm, > - 01:50 ohm(default), 10:45 ohm, 11:40 ohm. > - > - analogix,lane1-swing: > - $ref: /schemas/types.yaml#/definitions/uint8-array > - minItems: 1 > - maxItems: 20 > - description: > - an array of swing register setting for DP tx lane1 PHY. > - DP TX lane1 swing register setting same with lane0 > - swing, please refer lane0-swing property description. > - > - analogix,audio-enable: > - type: boolean > - description: let the driver enable audio HDMI codec function or not. > - > ports: > $ref: /schemas/graph.yaml#/properties/ports > > properties: > port@0: > - $ref: /schemas/graph.yaml#/$defs/port-base > - unevaluatedProperties: false > + $ref: /schemas/graph.yaml#/properties/port > description: > - MIPI DSI/DPI input. > - > - properties: > - endpoint: > - $ref: /schemas/media/video-interfaces.yaml# > - type: object > - additionalProperties: false > - > - properties: > - remote-endpoint: true > - > - bus-type: > - enum: [1, 5] > - default: 1 > - > - data-lanes: true > + Video port for MIPI DSI input. > > port@1: > $ref: /schemas/graph.yaml#/properties/port > @@ -143,9 +87,6 @@ examples: > vdd10-supply = <&pp1000_mipibrdg>; > vdd18-supply = <&pp1800_mipibrdg>; > vdd33-supply = <&pp3300_mipibrdg>; > - analogix,audio-enable; > - analogix,lane0-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; > - analogix,lane1-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; > > ports { > #address-cells = <1>; > @@ -155,8 +96,6 @@ examples: > reg = <0>; > anx7625_in: endpoint { > remote-endpoint = <&mipi_dsi>; > - bus-type = <5>; > - data-lanes = <0 1 2 3>; > }; > }; > > -- > 2.32.0 > Signed-off-by: Robert Foss <robert.foss@linaro.org>
On Mon, Mar 07, 2022 at 04:45:57PM +0100, Robert Foss wrote: > This reverts commit a43661e7e819b100e1f833a35018560a1d9abb39. S-o-b and reason for the revert? > --- > .../display/bridge/analogix,anx7625.yaml | 65 +------------------ > 1 file changed, 2 insertions(+), 63 deletions(-) > > diff --git a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > index 1d3e88daca041..ab48ab2f4240d 100644 > --- a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > +++ b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > @@ -43,70 +43,14 @@ properties: > vdd33-supply: > description: Regulator that provides the supply 3.3V power. > > - analogix,lane0-swing: > - $ref: /schemas/types.yaml#/definitions/uint8-array > - minItems: 1 > - maxItems: 20 > - description: > - an array of swing register setting for DP tx lane0 PHY. > - Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > - Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and > - [Swing control] setting. > - Registers 0~9, bit 3:0 is [Boost control], these bits control > - post cursor manual, increase the [Boost control] to increase > - Pre-emphasis value. > - Registers 0~9, bit 6:4 is [Swing control], these bits control > - swing manual, increase [Swing control] setting to add Vp-p value > - for each Swing, Pre. > - Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > - Swing1_Pre2, Swing0_Pre3, they are for [R select control] and > - [R Termination control] setting. > - Registers 10~19, bit 4:0 is [R select control], these bits are > - compensation manual, increase it can enhance IO driven strength > - and Vp-p. > - Registers 10~19, bit 5:6 is [R termination control], these bits > - adjust 50ohm impedance of DP tx termination. 00:55 ohm, > - 01:50 ohm(default), 10:45 ohm, 11:40 ohm. > - > - analogix,lane1-swing: > - $ref: /schemas/types.yaml#/definitions/uint8-array > - minItems: 1 > - maxItems: 20 > - description: > - an array of swing register setting for DP tx lane1 PHY. > - DP TX lane1 swing register setting same with lane0 > - swing, please refer lane0-swing property description. These apply to the DP side, so no need to revert this part. > - > - analogix,audio-enable: > - type: boolean > - description: let the driver enable audio HDMI codec function or not. > - Not sure on this one... > ports: > $ref: /schemas/graph.yaml#/properties/ports > > properties: > port@0: > - $ref: /schemas/graph.yaml#/$defs/port-base > - unevaluatedProperties: false > + $ref: /schemas/graph.yaml#/properties/port > description: > - MIPI DSI/DPI input. > - > - properties: > - endpoint: > - $ref: /schemas/media/video-interfaces.yaml# > - type: object > - additionalProperties: false > - > - properties: > - remote-endpoint: true > - > - bus-type: > - enum: [1, 5] I think the error here is really 1 should be 4 which corresponds to D-PHY which is used by both CSI and DSI. Otherwise, I don't really see the issue with bus-type being shared between CSI and DSI. > - default: 1 > - > - data-lanes: true > + Video port for MIPI DSI input. > > port@1: > $ref: /schemas/graph.yaml#/properties/port > @@ -143,9 +87,6 @@ examples: > vdd10-supply = <&pp1000_mipibrdg>; > vdd18-supply = <&pp1800_mipibrdg>; > vdd33-supply = <&pp3300_mipibrdg>; > - analogix,audio-enable; > - analogix,lane0-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; > - analogix,lane1-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; > > ports { > #address-cells = <1>; > @@ -155,8 +96,6 @@ examples: > reg = <0>; > anx7625_in: endpoint { > remote-endpoint = <&mipi_dsi>; > - bus-type = <5>; > - data-lanes = <0 1 2 3>; > }; > }; > > -- > 2.32.0 > >
On Mon, 7 Mar 2022 at 17:38, Rob Herring <robh@kernel.org> wrote: > > On Mon, Mar 07, 2022 at 04:45:57PM +0100, Robert Foss wrote: > > This reverts commit a43661e7e819b100e1f833a35018560a1d9abb39. > > S-o-b and reason for the revert? > > > --- > > .../display/bridge/analogix,anx7625.yaml | 65 +------------------ > > 1 file changed, 2 insertions(+), 63 deletions(-) > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > index 1d3e88daca041..ab48ab2f4240d 100644 > > --- a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > +++ b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > @@ -43,70 +43,14 @@ properties: > > vdd33-supply: > > description: Regulator that provides the supply 3.3V power. > > > > - analogix,lane0-swing: > > - $ref: /schemas/types.yaml#/definitions/uint8-array > > - minItems: 1 > > - maxItems: 20 > > - description: > > - an array of swing register setting for DP tx lane0 PHY. > > - Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > > - Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and > > - [Swing control] setting. > > - Registers 0~9, bit 3:0 is [Boost control], these bits control > > - post cursor manual, increase the [Boost control] to increase > > - Pre-emphasis value. > > - Registers 0~9, bit 6:4 is [Swing control], these bits control > > - swing manual, increase [Swing control] setting to add Vp-p value > > - for each Swing, Pre. > > - Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > > - Swing1_Pre2, Swing0_Pre3, they are for [R select control] and > > - [R Termination control] setting. > > - Registers 10~19, bit 4:0 is [R select control], these bits are > > - compensation manual, increase it can enhance IO driven strength > > - and Vp-p. > > - Registers 10~19, bit 5:6 is [R termination control], these bits > > - adjust 50ohm impedance of DP tx termination. 00:55 ohm, > > - 01:50 ohm(default), 10:45 ohm, 11:40 ohm. > > - > > - analogix,lane1-swing: > > - $ref: /schemas/types.yaml#/definitions/uint8-array > > - minItems: 1 > > - maxItems: 20 > > - description: > > - an array of swing register setting for DP tx lane1 PHY. > > - DP TX lane1 swing register setting same with lane0 > > - swing, please refer lane0-swing property description. > > These apply to the DP side, so no need to revert this part. Ack. > > > - > > - analogix,audio-enable: > > - type: boolean > > - description: let the driver enable audio HDMI codec function or not. > > - > > Not sure on this one... These additions are independent from my reading of this, would you like a v2 with only the bus-type related changes reverted? > > > ports: > > $ref: /schemas/graph.yaml#/properties/ports > > > > properties: > > port@0: > > - $ref: /schemas/graph.yaml#/$defs/port-base > > - unevaluatedProperties: false > > + $ref: /schemas/graph.yaml#/properties/port > > description: > > - MIPI DSI/DPI input. > > - > > - properties: > > - endpoint: > > - $ref: /schemas/media/video-interfaces.yaml# > > - type: object > > - additionalProperties: false > > - > > - properties: > > - remote-endpoint: true > > - > > - bus-type: > > - enum: [1, 5] > > I think the error here is really 1 should be 4 which corresponds to > D-PHY which is used by both CSI and DSI. Otherwise, I don't really see > the issue with bus-type being shared between CSI and DSI. I think that would be a correct solution. And ignoring everything else, the range of this property is something that should be fixed. But that would mean that CPI (camera parallel interface) and DPI (display parallel interface) would share the V4L2_FWNODE_BUS_TYPE_PARALLEL enum. I think that would be perfectly functional, but it is not what V4L2_FWNODE_BUS_TYPE_PARALLEL is documented to represent. As far as I can see it's only intended to represent CPI. Instead of having V4L2_FWNODE_BUS_TYPE_PARALLEL represent two standards, I think they should be split. And possibly V4L2_FWNODE_BUS_TYPE_PARALLEL should be renamed for CPI, but that is a separate story. This would provide for the neatest and most legible solution. If this solution is implemented, this range would be incorrect. Additionally the snippet reverted in 2/2 of this series would no longer be valid. As it stands V4L2_FWNODE_BUS_TYPE_PARALLEL was used to represent DPI due to not being caught in the review process. > > > - default: 1 > > - > > - data-lanes: true > > + Video port for MIPI DSI input. > > > > port@1: > > $ref: /schemas/graph.yaml#/properties/port > > @@ -143,9 +87,6 @@ examples: > > vdd10-supply = <&pp1000_mipibrdg>; > > vdd18-supply = <&pp1800_mipibrdg>; > > vdd33-supply = <&pp3300_mipibrdg>; > > - analogix,audio-enable; > > - analogix,lane0-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; > > - analogix,lane1-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; > > > > ports { > > #address-cells = <1>; > > @@ -155,8 +96,6 @@ examples: > > reg = <0>; > > anx7625_in: endpoint { > > remote-endpoint = <&mipi_dsi>; > > - bus-type = <5>; > > - data-lanes = <0 1 2 3>; > > }; > > }; > > > > -- > > 2.32.0 Signed-off-by: Robert Foss <robert.foss@linaro.org>
On Mon, Mar 07, 2022 at 05:57:47PM +0100, Robert Foss wrote: > On Mon, 7 Mar 2022 at 17:38, Rob Herring <robh@kernel.org> wrote: > > > > On Mon, Mar 07, 2022 at 04:45:57PM +0100, Robert Foss wrote: > > > This reverts commit a43661e7e819b100e1f833a35018560a1d9abb39. > > > > S-o-b and reason for the revert? > > > > > --- > > > .../display/bridge/analogix,anx7625.yaml | 65 +------------------ > > > 1 file changed, 2 insertions(+), 63 deletions(-) > > > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > > index 1d3e88daca041..ab48ab2f4240d 100644 > > > --- a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > > +++ b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > > @@ -43,70 +43,14 @@ properties: > > > vdd33-supply: > > > description: Regulator that provides the supply 3.3V power. > > > > > > - analogix,lane0-swing: > > > - $ref: /schemas/types.yaml#/definitions/uint8-array > > > - minItems: 1 > > > - maxItems: 20 > > > - description: > > > - an array of swing register setting for DP tx lane0 PHY. > > > - Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > > > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > > > - Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and > > > - [Swing control] setting. > > > - Registers 0~9, bit 3:0 is [Boost control], these bits control > > > - post cursor manual, increase the [Boost control] to increase > > > - Pre-emphasis value. > > > - Registers 0~9, bit 6:4 is [Swing control], these bits control > > > - swing manual, increase [Swing control] setting to add Vp-p value > > > - for each Swing, Pre. > > > - Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > > > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > > > - Swing1_Pre2, Swing0_Pre3, they are for [R select control] and > > > - [R Termination control] setting. > > > - Registers 10~19, bit 4:0 is [R select control], these bits are > > > - compensation manual, increase it can enhance IO driven strength > > > - and Vp-p. > > > - Registers 10~19, bit 5:6 is [R termination control], these bits > > > - adjust 50ohm impedance of DP tx termination. 00:55 ohm, > > > - 01:50 ohm(default), 10:45 ohm, 11:40 ohm. > > > - > > > - analogix,lane1-swing: > > > - $ref: /schemas/types.yaml#/definitions/uint8-array > > > - minItems: 1 > > > - maxItems: 20 > > > - description: > > > - an array of swing register setting for DP tx lane1 PHY. > > > - DP TX lane1 swing register setting same with lane0 > > > - swing, please refer lane0-swing property description. > > > > These apply to the DP side, so no need to revert this part. > > Ack. > > > > > > - > > > - analogix,audio-enable: > > > - type: boolean > > > - description: let the driver enable audio HDMI codec function or not. > > > - > > > > Not sure on this one... > > These additions are independent from my reading of this, would you > like a v2 with only the bus-type related changes reverted? > > > > > > ports: > > > $ref: /schemas/graph.yaml#/properties/ports > > > > > > properties: > > > port@0: > > > - $ref: /schemas/graph.yaml#/$defs/port-base > > > - unevaluatedProperties: false > > > + $ref: /schemas/graph.yaml#/properties/port > > > description: > > > - MIPI DSI/DPI input. > > > - > > > - properties: > > > - endpoint: > > > - $ref: /schemas/media/video-interfaces.yaml# > > > - type: object > > > - additionalProperties: false > > > - > > > - properties: > > > - remote-endpoint: true > > > - > > > - bus-type: > > > - enum: [1, 5] > > > > I think the error here is really 1 should be 4 which corresponds to > > D-PHY which is used by both CSI and DSI. Otherwise, I don't really see > > the issue with bus-type being shared between CSI and DSI. > > I think that would be a correct solution. And ignoring everything > else, the range of this property is something that should be fixed. > > But that would mean that CPI (camera parallel interface) and DPI > (display parallel interface) would share the > V4L2_FWNODE_BUS_TYPE_PARALLEL enum. I think that would be perfectly > functional, but it is not what V4L2_FWNODE_BUS_TYPE_PARALLEL is > documented to represent. As far as I can see it's only intended to > represent CPI. Are you aware of any standard documenting camera parallel interfaces with separate sync signals ? I was looking for that the other day, and couldn't find much. CPI seems to be an old MIPI standard, but I couldn't find any public document, I'not not sure if it actually matches. Another common parallel interface in SoCs is AXI4 Stream, which we will likely need a bus type for. We'll then have to decide on how to handle on-SoC custom parallel buses. > Instead of having V4L2_FWNODE_BUS_TYPE_PARALLEL represent two > standards, I think they should be split. And possibly > V4L2_FWNODE_BUS_TYPE_PARALLEL should be renamed for CPI, but that is a > separate story. This would provide for the neatest and most legible > solution. If this solution is implemented, this range would be > incorrect. Additionally the snippet reverted in 2/2 of this series > would no longer be valid. > > As it stands V4L2_FWNODE_BUS_TYPE_PARALLEL was used to represent DPI > due to not being caught in the review process. We may end up using those values, but I think it should be discussed and not rushed in v5.17 if possible. > > > - default: 1 > > > - > > > - data-lanes: true > > > + Video port for MIPI DSI input. > > > > > > port@1: > > > $ref: /schemas/graph.yaml#/properties/port > > > @@ -143,9 +87,6 @@ examples: > > > vdd10-supply = <&pp1000_mipibrdg>; > > > vdd18-supply = <&pp1800_mipibrdg>; > > > vdd33-supply = <&pp3300_mipibrdg>; > > > - analogix,audio-enable; > > > - analogix,lane0-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; > > > - analogix,lane1-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; > > > > > > ports { > > > #address-cells = <1>; > > > @@ -155,8 +96,6 @@ examples: > > > reg = <0>; > > > anx7625_in: endpoint { > > > remote-endpoint = <&mipi_dsi>; > > > - bus-type = <5>; > > > - data-lanes = <0 1 2 3>; > > > }; > > > }; > > > > > > -- > > > 2.32.0 > > Signed-off-by: Robert Foss <robert.foss@linaro.org>
On Mon, Mar 7, 2022 at 11:11 AM Laurent Pinchart <laurent.pinchart@ideasonboard.com> wrote: > > On Mon, Mar 07, 2022 at 05:57:47PM +0100, Robert Foss wrote: > > On Mon, 7 Mar 2022 at 17:38, Rob Herring <robh@kernel.org> wrote: > > > > > > On Mon, Mar 07, 2022 at 04:45:57PM +0100, Robert Foss wrote: > > > > This reverts commit a43661e7e819b100e1f833a35018560a1d9abb39. > > > > > > S-o-b and reason for the revert? > > > > > > > --- > > > > .../display/bridge/analogix,anx7625.yaml | 65 +------------------ > > > > 1 file changed, 2 insertions(+), 63 deletions(-) > > > > > > > > diff --git a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > > > index 1d3e88daca041..ab48ab2f4240d 100644 > > > > --- a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > > > +++ b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml > > > > @@ -43,70 +43,14 @@ properties: > > > > vdd33-supply: > > > > description: Regulator that provides the supply 3.3V power. > > > > > > > > - analogix,lane0-swing: > > > > - $ref: /schemas/types.yaml#/definitions/uint8-array > > > > - minItems: 1 > > > > - maxItems: 20 > > > > - description: > > > > - an array of swing register setting for DP tx lane0 PHY. > > > > - Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > > > > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > > > > - Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and > > > > - [Swing control] setting. > > > > - Registers 0~9, bit 3:0 is [Boost control], these bits control > > > > - post cursor manual, increase the [Boost control] to increase > > > > - Pre-emphasis value. > > > > - Registers 0~9, bit 6:4 is [Swing control], these bits control > > > > - swing manual, increase [Swing control] setting to add Vp-p value > > > > - for each Swing, Pre. > > > > - Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, > > > > - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, > > > > - Swing1_Pre2, Swing0_Pre3, they are for [R select control] and > > > > - [R Termination control] setting. > > > > - Registers 10~19, bit 4:0 is [R select control], these bits are > > > > - compensation manual, increase it can enhance IO driven strength > > > > - and Vp-p. > > > > - Registers 10~19, bit 5:6 is [R termination control], these bits > > > > - adjust 50ohm impedance of DP tx termination. 00:55 ohm, > > > > - 01:50 ohm(default), 10:45 ohm, 11:40 ohm. > > > > - > > > > - analogix,lane1-swing: > > > > - $ref: /schemas/types.yaml#/definitions/uint8-array > > > > - minItems: 1 > > > > - maxItems: 20 > > > > - description: > > > > - an array of swing register setting for DP tx lane1 PHY. > > > > - DP TX lane1 swing register setting same with lane0 > > > > - swing, please refer lane0-swing property description. > > > > > > These apply to the DP side, so no need to revert this part. > > > > Ack. > > > > > > > > > - > > > > - analogix,audio-enable: > > > > - type: boolean > > > > - description: let the driver enable audio HDMI codec function or not. > > > > - > > > > > > Not sure on this one... > > > > These additions are independent from my reading of this, would you > > like a v2 with only the bus-type related changes reverted? Yes. > > > > > > > > > ports: > > > > $ref: /schemas/graph.yaml#/properties/ports > > > > > > > > properties: > > > > port@0: > > > > - $ref: /schemas/graph.yaml#/$defs/port-base > > > > - unevaluatedProperties: false > > > > + $ref: /schemas/graph.yaml#/properties/port > > > > description: > > > > - MIPI DSI/DPI input. > > > > - > > > > - properties: > > > > - endpoint: > > > > - $ref: /schemas/media/video-interfaces.yaml# > > > > - type: object > > > > - additionalProperties: false > > > > - > > > > - properties: > > > > - remote-endpoint: true > > > > - > > > > - bus-type: > > > > - enum: [1, 5] > > > > > > I think the error here is really 1 should be 4 which corresponds to > > > D-PHY which is used by both CSI and DSI. Otherwise, I don't really see > > > the issue with bus-type being shared between CSI and DSI. > > > > I think that would be a correct solution. And ignoring everything > > else, the range of this property is something that should be fixed. > > > > But that would mean that CPI (camera parallel interface) and DPI > > (display parallel interface) would share the > > V4L2_FWNODE_BUS_TYPE_PARALLEL enum. I think that would be perfectly > > functional, but it is not what V4L2_FWNODE_BUS_TYPE_PARALLEL is > > documented to represent. As far as I can see it's only intended to > > represent CPI. > > Are you aware of any standard documenting camera parallel interfaces > with separate sync signals ? I was looking for that the other day, and > couldn't find much. CPI seems to be an old MIPI standard, but I couldn't > find any public document, I'not not sure if it actually matches. I don't recall. Generally, I think the camera side is not quite the mess the display side is with all the formats. > Another common parallel interface in SoCs is AXI4 Stream, which we will > likely need a bus type for. We'll then have to decide on how to handle > on-SoC custom parallel buses. Except for those maybe. > > Instead of having V4L2_FWNODE_BUS_TYPE_PARALLEL represent two > > standards, I think they should be split. And possibly > > V4L2_FWNODE_BUS_TYPE_PARALLEL should be renamed for CPI, but that is a > > separate story. This would provide for the neatest and most legible > > solution. If this solution is implemented, this range would be > > incorrect. Additionally the snippet reverted in 2/2 of this series > > would no longer be valid. > > > > As it stands V4L2_FWNODE_BUS_TYPE_PARALLEL was used to represent DPI > > due to not being caught in the review process. > > We may end up using those values, but I think it should be discussed and > not rushed in v5.17 if possible. Given it's not actually used (correctly), agreed. Rob
diff --git a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml index 1d3e88daca041..ab48ab2f4240d 100644 --- a/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml +++ b/Documentation/devicetree/bindings/display/bridge/analogix,anx7625.yaml @@ -43,70 +43,14 @@ properties: vdd33-supply: description: Regulator that provides the supply 3.3V power. - analogix,lane0-swing: - $ref: /schemas/types.yaml#/definitions/uint8-array - minItems: 1 - maxItems: 20 - description: - an array of swing register setting for DP tx lane0 PHY. - Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, - Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and - [Swing control] setting. - Registers 0~9, bit 3:0 is [Boost control], these bits control - post cursor manual, increase the [Boost control] to increase - Pre-emphasis value. - Registers 0~9, bit 6:4 is [Swing control], these bits control - swing manual, increase [Swing control] setting to add Vp-p value - for each Swing, Pre. - Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0, - Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2, - Swing1_Pre2, Swing0_Pre3, they are for [R select control] and - [R Termination control] setting. - Registers 10~19, bit 4:0 is [R select control], these bits are - compensation manual, increase it can enhance IO driven strength - and Vp-p. - Registers 10~19, bit 5:6 is [R termination control], these bits - adjust 50ohm impedance of DP tx termination. 00:55 ohm, - 01:50 ohm(default), 10:45 ohm, 11:40 ohm. - - analogix,lane1-swing: - $ref: /schemas/types.yaml#/definitions/uint8-array - minItems: 1 - maxItems: 20 - description: - an array of swing register setting for DP tx lane1 PHY. - DP TX lane1 swing register setting same with lane0 - swing, please refer lane0-swing property description. - - analogix,audio-enable: - type: boolean - description: let the driver enable audio HDMI codec function or not. - ports: $ref: /schemas/graph.yaml#/properties/ports properties: port@0: - $ref: /schemas/graph.yaml#/$defs/port-base - unevaluatedProperties: false + $ref: /schemas/graph.yaml#/properties/port description: - MIPI DSI/DPI input. - - properties: - endpoint: - $ref: /schemas/media/video-interfaces.yaml# - type: object - additionalProperties: false - - properties: - remote-endpoint: true - - bus-type: - enum: [1, 5] - default: 1 - - data-lanes: true + Video port for MIPI DSI input. port@1: $ref: /schemas/graph.yaml#/properties/port @@ -143,9 +87,6 @@ examples: vdd10-supply = <&pp1000_mipibrdg>; vdd18-supply = <&pp1800_mipibrdg>; vdd33-supply = <&pp3300_mipibrdg>; - analogix,audio-enable; - analogix,lane0-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; - analogix,lane1-swing = /bits/ 8 <0x14 0x54 0x64 0x74>; ports { #address-cells = <1>; @@ -155,8 +96,6 @@ examples: reg = <0>; anx7625_in: endpoint { remote-endpoint = <&mipi_dsi>; - bus-type = <5>; - data-lanes = <0 1 2 3>; }; };