@@ -590,6 +590,16 @@ config SPI_MTK_NOR
SPI interface as well as several SPI NOR specific instructions
via SPI MEM interface.
+config SPI_MTK_SNFI
+ tristate "MediaTek SPI NAND Flash Interface"
+ depends on ARCH_MEDIATEK || COMPILE_TEST
+ depends on MTD_NAND_ECC_MEDIATEK
+ help
+ This enables support for SPI-NAND mode on the MediaTek NAND
+ Flash Interface found on MediaTek ARM SoCs. This controller
+ is implemented as a SPI-MEM controller with pipelined ECC
+ capcability.
+
config SPI_NPCM_FIU
tristate "Nuvoton NPCM FLASH Interface Unit"
depends on ARCH_NPCM || COMPILE_TEST
@@ -76,6 +76,7 @@ obj-$(CONFIG_SPI_MPC52xx) += spi-mpc52xx.o
obj-$(CONFIG_SPI_MT65XX) += spi-mt65xx.o
obj-$(CONFIG_SPI_MT7621) += spi-mt7621.o
obj-$(CONFIG_SPI_MTK_NOR) += spi-mtk-nor.o
+obj-$(CONFIG_SPI_MTK_SNFI) += spi-mtk-snfi.o
obj-$(CONFIG_SPI_MXIC) += spi-mxic.o
obj-$(CONFIG_SPI_MXS) += spi-mxs.o
obj-$(CONFIG_SPI_NPCM_FIU) += spi-npcm-fiu.o
new file mode 100644
@@ -0,0 +1,1351 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Driver for the SPI-NAND mode of Mediatek NAND Flash Interface
+//
+// Copyright (c) 2022 Chuanhong Guo <gch981213@gmail.com>
+//
+// This driver is based on the SPI-NAND mtd driver from Mediatek SDK:
+//
+// Copyright (C) 2020 MediaTek Inc.
+// Author: Weijie Gao <weijie.gao@mediatek.com>
+//
+// This controller organize the page data as several interleaved sectors
+// like the following: (sizeof(FDM + ECC) = snf->nfi_cfg.spare_size)
+// +---------+------+------+---------+------+------+-----+
+// | Sector1 | FDM1 | ECC1 | Sector2 | FDM2 | ECC2 | ... |
+// +---------+------+------+---------+------+------+-----+
+// With auto-format turned on, DMA only returns this part:
+// +---------+---------+-----+
+// | Sector1 | Sector2 | ... |
+// +---------+---------+-----+
+// The FDM data will be filled to the registers, and ECC parity data isn't
+// accessible.
+// With auto-format off, all ((Sector+FDM+ECC)*nsectors) will be read over DMA
+// in it's original order shown in the first table. ECC can't be turned on when
+// auto-format is off.
+//
+// However, Linux SPI-NAND driver expects the data returned as:
+// +------+-----+
+// | Page | OOB |
+// +------+-----+
+// where the page data is continuously stored instead of interleaved.
+// So we assume all instructions matching the page_op template between ECC
+// prepare_io_req and finish_io_req are for page cache r/w.
+// Here's how this spi-mem driver operates when reading:
+// 1. Always set snf->autofmt = true in prepare_io_req (even when ECC is off).
+// 2. Perform page ops and let the controller fill the DMA bounce buffer with
+// de-interleaved sector data and set FDM registers.
+// 3. Return the data as:
+// +---------+---------+-----+------+------+-----+
+// | Sector1 | Sector2 | ... | FDM1 | FDM2 | ... |
+// +---------+---------+-----+------+------+-----+
+// 4. For other matching spi_mem ops outside a prepare/finish_io_req pair,
+// read the data with auto-format off into the bounce buffer and copy
+// needed data to the buffer specified in the request.
+//
+// Write requests operates in a similar manner.
+// As a limitation of this strategy, we won't be able to access any ECC parity
+// data at all in Linux.
+//
+// Here's the bad block mark situation on MTK chips:
+// In older chips like mt7622, MTK uses the first FDM byte in the first sector
+// as the bad block mark. After de-interleaving, this byte appears at [pagesize]
+// in the returned data, which is the BBM position expected by kernel. However,
+// the conventional bad block mark is the first byte of the OOB, which is part
+// of the last sector data in the interleaved layout. Instead of fixing their
+// hardware, MTK decided to address this inconsistency in software. On these
+// later chips, the BootROM expects the following:
+// 1. The [pagesize] byte on a nand page is used as BBM, which will appear at
+// (page_size - (nsectors - 1) * spare_size) in the DMA buffer.
+// 2. The original byte stored at that position in the DMA buffer will be stored
+// as the first byte of the FDM section in the last sector.
+// We can't disagree with the BootROM, so after de-interleaving, we need to
+// perform the following swaps in read:
+// 1. Store the BBM at [page_size - (nsectors - 1) * spare_size] to [page_size],
+// which is the expected BBM position by kernel.
+// 2. Store the page data byte at [pagesize + (nsectors-1) * fdm] back to
+// [page_size - (nsectors - 1) * spare_size]
+// Similarly, when writing, we need to perform swaps in the other direction.
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/mutex.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
+#include <linux/of_platform.h>
+#include <linux/mtd/nand-ecc-mtk.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+#include <linux/mtd/nand.h>
+
+// NFI registers
+#define NFI_CNFG 0x000
+#define CNFG_OP_MODE_S 12
+#define CNFG_OP_MODE_CUST 6
+#define CNFG_OP_MODE_PROGRAM 3
+#define CNFG_AUTO_FMT_EN BIT(9)
+#define CNFG_HW_ECC_EN BIT(8)
+#define CNFG_DMA_BURST_EN BIT(2)
+#define CNFG_READ_MODE BIT(1)
+#define CNFG_DMA_MODE BIT(0)
+
+#define NFI_PAGEFMT 0x0004
+#define NFI_SPARE_SIZE_LS_S 16
+#define NFI_FDM_ECC_NUM_S 12
+#define NFI_FDM_NUM_S 8
+#define NFI_SPARE_SIZE_S 4
+#define NFI_SEC_SEL_512 BIT(2)
+#define NFI_PAGE_SIZE_S 0
+#define NFI_PAGE_SIZE_512_2K 0
+#define NFI_PAGE_SIZE_2K_4K 1
+#define NFI_PAGE_SIZE_4K_8K 2
+#define NFI_PAGE_SIZE_8K_16K 3
+
+#define NFI_CON 0x008
+#define CON_SEC_NUM_S 12
+#define CON_BWR BIT(9)
+#define CON_BRD BIT(8)
+#define CON_NFI_RST BIT(1)
+#define CON_FIFO_FLUSH BIT(0)
+
+#define NFI_INTR_EN 0x010
+#define NFI_INTR_STA 0x014
+#define NFI_IRQ_INTR_EN BIT(31)
+#define NFI_IRQ_CUS_READ BIT(8)
+#define NFI_IRQ_CUS_PG BIT(7)
+
+#define NFI_CMD 0x020
+#define NFI_CMD_DUMMY_READ 0x00
+#define NFI_CMD_DUMMY_WRITE 0x80
+
+#define NFI_STRDATA 0x040
+#define STR_DATA BIT(0)
+
+#define NFI_STA 0x060
+#define NFI_NAND_FSM GENMASK(28, 24)
+#define NFI_FSM GENMASK(19, 16)
+#define READ_EMPTY BIT(12)
+
+#define NFI_FIFOSTA 0x064
+#define FIFO_WR_REMAIN_S 8
+#define FIFO_RD_REMAIN_S 0
+
+#define NFI_ADDRCNTR 0x070
+#define SEC_CNTR GENMASK(16, 12)
+#define SEC_CNTR_S 12
+#define NFI_SEC_CNTR(val) (((val)&SEC_CNTR) >> SEC_CNTR_S)
+
+#define NFI_STRADDR 0x080
+
+#define NFI_BYTELEN 0x084
+#define BUS_SEC_CNTR(val) (((val)&SEC_CNTR) >> SEC_CNTR_S)
+
+#define NFI_FDM0L 0x0a0
+#define NFI_FDM0M 0x0a4
+#define NFI_FDML(n) (NFI_FDM0L + (n)*8)
+#define NFI_FDMM(n) (NFI_FDM0M + (n)*8)
+
+#define NFI_DEBUG_CON1 0x220
+#define WBUF_EN BIT(2)
+
+#define NFI_MASTERSTA 0x224
+#define MAS_ADDR GENMASK(11, 9)
+#define MAS_RD GENMASK(8, 6)
+#define MAS_WR GENMASK(5, 3)
+#define MAS_RDDLY GENMASK(2, 0)
+#define NFI_MASTERSTA_MASK_7622 (MAS_ADDR | MAS_RD | MAS_WR | MAS_RDDLY)
+
+// SNFI registers
+#define SNF_MAC_CTL 0x500
+#define MAC_XIO_SEL BIT(4)
+#define SF_MAC_EN BIT(3)
+#define SF_TRIG BIT(2)
+#define WIP_READY BIT(1)
+#define WIP BIT(0)
+
+#define SNF_MAC_OUTL 0x504
+#define SNF_MAC_INL 0x508
+
+#define SNF_RD_CTL2 0x510
+#define DATA_READ_DUMMY_S 8
+#define DATA_READ_MAX_DUMMY 0xf
+#define DATA_READ_CMD_S 0
+
+#define SNF_RD_CTL3 0x514
+
+#define SNF_PG_CTL1 0x524
+#define PG_LOAD_CMD_S 8
+
+#define SNF_PG_CTL2 0x528
+
+#define SNF_MISC_CTL 0x538
+#define SW_RST BIT(28)
+#define FIFO_RD_LTC_S 25
+#define PG_LOAD_X4_EN BIT(20)
+#define DATA_READ_MODE_S 16
+#define DATA_READ_MODE GENMASK(18, 16)
+#define DATA_READ_MODE_X1 0
+#define DATA_READ_MODE_X2 1
+#define DATA_READ_MODE_X4 2
+#define DATA_READ_MODE_DUAL 5
+#define DATA_READ_MODE_QUAD 6
+#define PG_LOAD_CUSTOM_EN BIT(7)
+#define DATARD_CUSTOM_EN BIT(6)
+#define CS_DESELECT_CYC_S 0
+
+#define SNF_MISC_CTL2 0x53c
+#define PROGRAM_LOAD_BYTE_NUM_S 16
+#define READ_DATA_BYTE_NUM_S 11
+
+#define SNF_DLY_CTL3 0x548
+#define SFCK_SAM_DLY_S 0
+
+#define SNF_STA_CTL1 0x550
+#define CUS_PG_DONE BIT(28)
+#define CUS_READ_DONE BIT(27)
+#define SPI_STATE_S 0
+#define SPI_STATE GENMASK(3, 0)
+
+#define SNF_CFG 0x55c
+#define SPI_MODE BIT(0)
+
+#define SNF_GPRAM 0x800
+#define SNF_GPRAM_SIZE 0xa0
+
+#define SNFI_POLL_INTERVAL 1000000
+
+static const uint8_t mt7622_spare_sizes[] = { 16, 26, 27, 28 };
+
+struct mtk_snand_caps {
+ uint16_t sector_size;
+ uint16_t max_sectors;
+ uint16_t fdm_size;
+ uint16_t fdm_ecc_size;
+ uint16_t fifo_size;
+
+ bool bbm_swap;
+ bool empty_page_check;
+ uint32_t mastersta_mask;
+
+ const uint8_t *spare_sizes;
+ uint32_t num_spare_size;
+};
+
+static const struct mtk_snand_caps mt7622_snand_caps = {
+ .sector_size = 512,
+ .max_sectors = 8,
+ .fdm_size = 8,
+ .fdm_ecc_size = 1,
+ .fifo_size = 32,
+ .bbm_swap = false,
+ .empty_page_check = false,
+ .mastersta_mask = NFI_MASTERSTA_MASK_7622,
+ .spare_sizes = mt7622_spare_sizes,
+ .num_spare_size = ARRAY_SIZE(mt7622_spare_sizes)
+};
+
+static const struct mtk_snand_caps mt7629_snand_caps = {
+ .sector_size = 512,
+ .max_sectors = 8,
+ .fdm_size = 8,
+ .fdm_ecc_size = 1,
+ .fifo_size = 32,
+ .bbm_swap = true,
+ .empty_page_check = false,
+ .mastersta_mask = NFI_MASTERSTA_MASK_7622,
+ .spare_sizes = mt7622_spare_sizes,
+ .num_spare_size = ARRAY_SIZE(mt7622_spare_sizes)
+};
+
+struct mtk_snand_conf {
+ size_t page_size;
+ size_t oob_size;
+ u8 nsectors;
+ u8 spare_size;
+};
+
+struct mtk_snand {
+ struct spi_controller *ctlr;
+ struct device *dev;
+ struct clk *nfi_clk;
+ struct clk *pad_clk;
+ void __iomem *nfi_base;
+ int irq;
+ struct completion op_done;
+ const struct mtk_snand_caps *caps;
+ struct mtk_ecc_config ecc_cfg;
+ struct mtk_ecc *ecc;
+ struct mtk_snand_conf nfi_cfg;
+ struct mtk_ecc_stats ecc_stats;
+ struct nand_ecc_engine ecc_eng;
+ bool autofmt;
+ u8 *buf;
+ dma_addr_t buf_dma;
+ size_t buf_len;
+};
+
+static struct mtk_snand *nand_to_mtk_snand(struct nand_device *nand)
+{
+ struct nand_ecc_engine *eng = nand->ecc.engine;
+
+ return container_of(eng, struct mtk_snand, ecc_eng);
+}
+
+static inline int snand_prepare_bouncebuf(struct mtk_snand *snf, size_t size)
+{
+ if (snf->buf_len >= size)
+ return 0;
+ if (snf->buf)
+ dmam_free_coherent(snf->dev, snf->buf_len, snf->buf,
+ snf->buf_dma);
+ snf->buf =
+ dmam_alloc_coherent(snf->dev, size, &snf->buf_dma, GFP_KERNEL);
+ if (!snf->buf)
+ return -ENOMEM;
+ snf->buf_len = size;
+ memset(snf->buf, 0xff, snf->buf_len);
+ return 0;
+}
+
+static inline uint32_t nfi_read32(struct mtk_snand *snf, uint32_t reg)
+{
+ return readl(snf->nfi_base + reg);
+}
+
+static inline void nfi_write32(struct mtk_snand *snf, uint32_t reg,
+ uint32_t val)
+{
+ writel(val, snf->nfi_base + reg);
+}
+
+static inline void nfi_write16(struct mtk_snand *snf, uint32_t reg,
+ uint16_t val)
+{
+ writew(val, snf->nfi_base + reg);
+}
+
+static inline void nfi_rmw32(struct mtk_snand *snf, uint32_t reg, uint32_t clr,
+ uint32_t set)
+{
+ uint32_t val;
+
+ val = readl(snf->nfi_base + reg);
+ val &= ~clr;
+ val |= set;
+ writel(val, snf->nfi_base + reg);
+}
+
+static void nfi_read_data(struct mtk_snand *snf, uint32_t reg, uint8_t *data,
+ uint32_t len)
+{
+ uint32_t i, val = 0, es = sizeof(uint32_t);
+
+ for (i = reg; i < reg + len; i++) {
+ if (i == reg || i % es == 0)
+ val = nfi_read32(snf, i & ~(es - 1));
+
+ *data++ = (uint8_t)(val >> (8 * (i % es)));
+ }
+}
+
+static int mtk_nfi_reset(struct mtk_snand *snf)
+{
+ uint32_t val, fifo_mask;
+ int ret;
+
+ nfi_write32(snf, NFI_CON, CON_FIFO_FLUSH | CON_NFI_RST);
+
+ ret = readw_poll_timeout(snf->nfi_base + NFI_MASTERSTA, val,
+ !(val & snf->caps->mastersta_mask), 0,
+ SNFI_POLL_INTERVAL);
+ if (ret) {
+ dev_err(snf->dev, "NFI master is still busy after reset\n");
+ return ret;
+ }
+
+ ret = readl_poll_timeout(snf->nfi_base + NFI_STA, val,
+ !(val & (NFI_FSM | NFI_NAND_FSM)), 0,
+ SNFI_POLL_INTERVAL);
+ if (ret) {
+ dev_err(snf->dev, "Failed to reset NFI\n");
+ return ret;
+ }
+
+ fifo_mask = ((snf->caps->fifo_size - 1) << FIFO_RD_REMAIN_S) |
+ ((snf->caps->fifo_size - 1) << FIFO_WR_REMAIN_S);
+ ret = readw_poll_timeout(snf->nfi_base + NFI_FIFOSTA, val,
+ !(val & fifo_mask), 0, SNFI_POLL_INTERVAL);
+ if (ret) {
+ dev_err(snf->dev, "NFI FIFOs are not empty\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int mtk_snand_mac_reset(struct mtk_snand *snf)
+{
+ int ret;
+ uint32_t val;
+
+ nfi_rmw32(snf, SNF_MISC_CTL, 0, SW_RST);
+
+ ret = readl_poll_timeout(snf->nfi_base + SNF_STA_CTL1, val,
+ !(val & SPI_STATE), 0, SNFI_POLL_INTERVAL);
+ if (ret)
+ dev_err(snf->dev, "Failed to reset SNFI MAC\n");
+
+ nfi_write32(snf, SNF_MISC_CTL,
+ (2 << FIFO_RD_LTC_S) | (10 << CS_DESELECT_CYC_S));
+
+ return ret;
+}
+
+static int mtk_snand_mac_trigger(struct mtk_snand *snf, uint32_t outlen,
+ uint32_t inlen)
+{
+ int ret;
+ uint32_t val;
+
+ nfi_write32(snf, SNF_MAC_CTL, SF_MAC_EN);
+ nfi_write32(snf, SNF_MAC_OUTL, outlen);
+ nfi_write32(snf, SNF_MAC_INL, inlen);
+
+ nfi_write32(snf, SNF_MAC_CTL, SF_MAC_EN | SF_TRIG);
+
+ ret = readl_poll_timeout(snf->nfi_base + SNF_MAC_CTL, val,
+ val & WIP_READY, 0, SNFI_POLL_INTERVAL);
+ if (ret) {
+ dev_err(snf->dev, "Timed out waiting for WIP_READY\n");
+ goto cleanup;
+ }
+
+ ret = readl_poll_timeout(snf->nfi_base + SNF_MAC_CTL, val, !(val & WIP),
+ 0, SNFI_POLL_INTERVAL);
+ if (ret)
+ dev_err(snf->dev, "Timed out waiting for WIP cleared\n");
+
+cleanup:
+ nfi_write32(snf, SNF_MAC_CTL, 0);
+
+ return ret;
+}
+
+static int mtk_snand_mac_io(struct mtk_snand *snf, const struct spi_mem_op *op)
+{
+ u32 rx_len = 0;
+ u32 reg_offs = 0;
+ u32 val = 0;
+ const u8 *tx_buf = NULL;
+ u8 *rx_buf = NULL;
+ int i, ret;
+ u8 b;
+
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ rx_len = op->data.nbytes;
+ rx_buf = op->data.buf.in;
+ } else {
+ tx_buf = op->data.buf.out;
+ }
+
+ mtk_snand_mac_reset(snf);
+
+ for (i = 0; i < op->cmd.nbytes; i++, reg_offs++) {
+ b = (op->cmd.opcode >> ((op->cmd.nbytes - i - 1) * 8)) & 0xff;
+ val |= b << (8 * (reg_offs % 4));
+ if (reg_offs % 4 == 3) {
+ nfi_write32(snf, SNF_GPRAM + reg_offs - 3, val);
+ val = 0;
+ }
+ }
+
+ for (i = 0; i < op->addr.nbytes; i++, reg_offs++) {
+ b = (op->addr.val >> ((op->addr.nbytes - i - 1) * 8)) & 0xff;
+ val |= b << (8 * (reg_offs % 4));
+ if (reg_offs % 4 == 3) {
+ nfi_write32(snf, SNF_GPRAM + reg_offs - 3, val);
+ val = 0;
+ }
+ }
+
+ for (i = 0; i < op->dummy.nbytes; i++, reg_offs++) {
+ if (reg_offs % 4 == 3) {
+ nfi_write32(snf, SNF_GPRAM + reg_offs - 3, val);
+ val = 0;
+ }
+ }
+
+ if (op->data.dir == SPI_MEM_DATA_OUT) {
+ for (i = 0; i < op->data.nbytes; i++, reg_offs++) {
+ val |= tx_buf[i] << (8 * (reg_offs % 4));
+ if (reg_offs % 4 == 3) {
+ nfi_write32(snf, SNF_GPRAM + reg_offs - 3, val);
+ val = 0;
+ }
+ }
+ }
+
+ if (reg_offs % 4 != 3)
+ nfi_write32(snf, SNF_GPRAM + (reg_offs & ~3), val);
+
+ for (i = 0; i < reg_offs; i += 4)
+ dev_dbg(snf->dev, "%d: %08X", i,
+ nfi_read32(snf, SNF_GPRAM + i));
+
+ dev_dbg(snf->dev, "SNF TX: %u RX: %u", reg_offs, rx_len);
+
+ ret = mtk_snand_mac_trigger(snf, reg_offs, rx_len);
+ if (ret)
+ return ret;
+
+ if (!rx_len)
+ return 0;
+
+ nfi_read_data(snf, SNF_GPRAM + reg_offs, rx_buf, rx_len);
+ return 0;
+}
+
+static int mtk_snand_setup_pagefmt(struct mtk_snand *snf, u32 page_size,
+ u32 oob_size)
+{
+ int spare_idx = -1;
+ u32 msg_size, spare_size, parity_bits, max_ecc_bytes;
+ u32 spare_size_shift, pagesize_idx;
+ u32 sector_size_512;
+ u8 nsectors;
+ int i;
+
+ // skip if it's already configured as required.
+ if (snf->nfi_cfg.page_size == page_size &&
+ snf->nfi_cfg.oob_size == oob_size)
+ return 0;
+
+ nsectors = page_size / snf->caps->sector_size;
+ if (nsectors > snf->caps->max_sectors) {
+ dev_err(snf->dev, "too many sectors required.\n");
+ goto err;
+ }
+
+ if (snf->caps->sector_size == 512) {
+ sector_size_512 = NFI_SEC_SEL_512;
+ spare_size_shift = NFI_SPARE_SIZE_S;
+ } else {
+ sector_size_512 = 0;
+ spare_size_shift = NFI_SPARE_SIZE_LS_S;
+ }
+
+ switch (page_size) {
+ case SZ_512:
+ pagesize_idx = NFI_PAGE_SIZE_512_2K;
+ break;
+ case SZ_2K:
+ if (snf->caps->sector_size == 512)
+ pagesize_idx = NFI_PAGE_SIZE_2K_4K;
+ else
+ pagesize_idx = NFI_PAGE_SIZE_512_2K;
+ break;
+ case SZ_4K:
+ if (snf->caps->sector_size == 512)
+ pagesize_idx = NFI_PAGE_SIZE_4K_8K;
+ else
+ pagesize_idx = NFI_PAGE_SIZE_2K_4K;
+ break;
+ case SZ_8K:
+ if (snf->caps->sector_size == 512)
+ pagesize_idx = NFI_PAGE_SIZE_8K_16K;
+ else
+ pagesize_idx = NFI_PAGE_SIZE_4K_8K;
+ break;
+ case SZ_16K:
+ pagesize_idx = NFI_PAGE_SIZE_8K_16K;
+ break;
+ default:
+ dev_err(snf->dev, "unsupported page size.\n");
+ goto err;
+ }
+
+ spare_size = oob_size / nsectors;
+ // If we're using the 1KB sector size, HW will automatically double the
+ // spare size. We should only use half of the value in this case.
+ if (snf->caps->sector_size == 1024)
+ spare_size /= 2;
+
+ for (i = snf->caps->num_spare_size - 1; i >= 0; i--) {
+ if (snf->caps->spare_sizes[i] <= spare_size) {
+ spare_size = snf->caps->spare_sizes[i];
+ if (snf->caps->sector_size == 1024)
+ spare_size *= 2;
+ spare_idx = i;
+ break;
+ }
+ }
+
+ if (spare_idx < 0) {
+ dev_err(snf->dev, "unsupported spare size: %u\n", spare_size);
+ goto err;
+ }
+
+ nfi_write32(snf, NFI_PAGEFMT,
+ (snf->caps->fdm_ecc_size << NFI_FDM_ECC_NUM_S) |
+ (snf->caps->fdm_size << NFI_FDM_NUM_S) |
+ (spare_idx << spare_size_shift) |
+ (pagesize_idx << NFI_PAGE_SIZE_S) |
+ sector_size_512);
+
+ msg_size = snf->caps->sector_size + snf->caps->fdm_ecc_size;
+ snf->ecc_cfg.len = msg_size;
+ parity_bits = fls(1 + 8 * msg_size);
+ max_ecc_bytes = spare_size - snf->caps->fdm_size;
+ snf->ecc_cfg.strength = max_ecc_bytes * 8 / parity_bits;
+ mtk_ecc_adjust_strength(snf->ecc, &snf->ecc_cfg.strength);
+
+ snf->nfi_cfg.page_size = page_size;
+ snf->nfi_cfg.oob_size = oob_size;
+ snf->nfi_cfg.nsectors = nsectors;
+ snf->nfi_cfg.spare_size = spare_size;
+
+ snf->ecc_cfg.mode = ECC_NFI_MODE;
+ snf->ecc_cfg.sectors = nsectors;
+
+ dev_info(snf->dev, "page format: (%u + %u) * %u, ECC strength: %u\n",
+ snf->caps->sector_size, spare_size, nsectors,
+ snf->ecc_cfg.strength);
+ return snand_prepare_bouncebuf(snf, page_size + oob_size);
+err:
+ dev_err(snf->dev, "page size %u + %u is not supported\n", page_size,
+ oob_size);
+ return -EOPNOTSUPP;
+}
+
+static int mtk_snand_ooblayout_ecc(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobecc)
+{
+ // ECC area is not accessible
+ return -ERANGE;
+}
+
+static int mtk_snand_ooblayout_free(struct mtd_info *mtd, int section,
+ struct mtd_oob_region *oobfree)
+{
+ struct nand_device *nand = mtd_to_nanddev(mtd);
+ struct mtk_snand *ms = nand_to_mtk_snand(nand);
+
+ if (section >= ms->nfi_cfg.nsectors)
+ return -ERANGE;
+
+ oobfree->length = ms->caps->fdm_size - 1;
+ oobfree->offset = section * ms->caps->fdm_size + 1;
+ return 0;
+}
+
+static const struct mtd_ooblayout_ops mtk_snand_ooblayout = {
+ .ecc = mtk_snand_ooblayout_ecc,
+ .free = mtk_snand_ooblayout_free,
+};
+
+static int mtk_snand_ecc_init_ctx(struct nand_device *nand)
+{
+ struct mtk_snand *snf = nand_to_mtk_snand(nand);
+ struct nand_ecc_props *conf = &nand->ecc.ctx.conf;
+ struct mtd_info *mtd = nanddev_to_mtd(nand);
+ int ret;
+
+ ret = mtk_snand_setup_pagefmt(snf, nand->memorg.pagesize,
+ nand->memorg.oobsize);
+ if (ret)
+ return ret;
+
+ mtd_set_ooblayout(mtd, &mtk_snand_ooblayout);
+
+ // This driver ignores any ECC capability configured by user or
+ // requested by the nand chip because the BootROM and MTK bootloader
+ // expects the page format to be the exact one as calculated in
+ // setup_pagefmt.
+ conf->step_size = snf->caps->sector_size;
+ conf->strength = snf->ecc_cfg.strength;
+
+ return 0;
+}
+
+static int mtk_snand_ecc_prepare_io_req(struct nand_device *nand,
+ struct nand_page_io_req *req)
+{
+ struct mtk_snand *snf = nand_to_mtk_snand(nand);
+ int ret;
+
+ ret = mtk_snand_setup_pagefmt(snf, nand->memorg.pagesize,
+ nand->memorg.oobsize);
+ if (ret)
+ return ret;
+ snf->autofmt = true;
+ return 0;
+}
+
+static int mtk_snand_ecc_finish_io_req(struct nand_device *nand,
+ struct nand_page_io_req *req)
+{
+ struct mtk_snand *snf = nand_to_mtk_snand(nand);
+ struct mtd_info *mtd = nanddev_to_mtd(nand);
+
+ snf->autofmt = false;
+ if ((req->mode == MTD_OPS_RAW) || (req->type != NAND_PAGE_READ))
+ return 0;
+
+ if (snf->ecc_stats.failed)
+ mtd->ecc_stats.failed += snf->ecc_stats.failed;
+ mtd->ecc_stats.corrected += snf->ecc_stats.corrected;
+ return snf->ecc_stats.failed ? -EBADMSG : snf->ecc_stats.bitflips;
+}
+
+static struct nand_ecc_engine_ops mtk_snfi_ecc_engine_ops = {
+ .init_ctx = mtk_snand_ecc_init_ctx,
+ .prepare_io_req = mtk_snand_ecc_prepare_io_req,
+ .finish_io_req = mtk_snand_ecc_finish_io_req,
+};
+
+static void mtk_snand_read_fdm(struct mtk_snand *snf, uint8_t *buf)
+{
+ uint32_t vall, valm;
+ uint8_t *oobptr = buf;
+ int i, j;
+
+ for (i = 0; i < snf->nfi_cfg.nsectors; i++) {
+ vall = nfi_read32(snf, NFI_FDML(i));
+ valm = nfi_read32(snf, NFI_FDMM(i));
+
+ for (j = 0; j < snf->caps->fdm_size; j++)
+ oobptr[j] = (j >= 4 ? valm : vall) >> ((j % 4) * 8);
+
+ oobptr += snf->caps->fdm_size;
+ }
+}
+
+static void mtk_snand_bm_swap(struct mtk_snand *snf)
+{
+ uint32_t buf_bbm_pos, fdm_bbm_pos;
+
+ if (!snf->caps->bbm_swap || snf->nfi_cfg.nsectors == 1)
+ return;
+
+ // swap [pagesize] byte on nand with the first fdm byte
+ // in the last sector.
+ buf_bbm_pos = snf->nfi_cfg.page_size -
+ (snf->nfi_cfg.nsectors - 1) * snf->nfi_cfg.spare_size;
+ fdm_bbm_pos = snf->nfi_cfg.page_size +
+ (snf->nfi_cfg.nsectors - 1) * snf->caps->fdm_size;
+
+ swap(snf->buf[fdm_bbm_pos], snf->buf[buf_bbm_pos]);
+}
+
+static void mtk_snand_fdm_bm_swap(struct mtk_snand *snf)
+{
+ uint32_t fdm_bbm_pos1, fdm_bbm_pos2;
+
+ if (!snf->caps->bbm_swap || snf->nfi_cfg.nsectors == 1)
+ return;
+
+ // swap the first fdm byte in the first and the last sector.
+ fdm_bbm_pos1 = snf->nfi_cfg.page_size;
+ fdm_bbm_pos2 = snf->nfi_cfg.page_size +
+ (snf->nfi_cfg.nsectors - 1) * snf->caps->fdm_size;
+ swap(snf->buf[fdm_bbm_pos1], snf->buf[fdm_bbm_pos2]);
+}
+
+static int mtk_snand_read_page_cache(struct mtk_snand *snf,
+ const struct spi_mem_op *op)
+{
+ // the address part to be sent by the controller
+ u32 op_addr = op->addr.val;
+ // where to start copying data from bounce buffer
+ u32 rd_offset = 0;
+ u32 dummy_clk = (op->dummy.nbytes * BITS_PER_BYTE / op->dummy.buswidth);
+ u32 op_mode = 0;
+ int ret = 0;
+ u32 rd_mode, rd_bytes, val;
+
+ if (snf->autofmt) {
+ u32 last_bit;
+ u32 mask;
+
+ op_mode = CNFG_AUTO_FMT_EN;
+ if (op->data.ecc)
+ op_mode |= CNFG_HW_ECC_EN;
+ // extract the plane bit:
+ // Find the highest bit set in (pagesize+oobsize).
+ // Bits higher than that in op->addr are kept and sent over SPI
+ // Lower bits are used as an offset for copying data from DMA
+ // bounce buffer.
+ last_bit = fls(snf->nfi_cfg.page_size + snf->nfi_cfg.oob_size);
+ mask = (1 << last_bit) - 1;
+ rd_offset = op_addr & mask;
+ op_addr &= ~mask;
+ }
+ mtk_snand_mac_reset(snf);
+ mtk_nfi_reset(snf);
+
+ // command and dummy cycles
+ nfi_write32(snf, SNF_RD_CTL2,
+ (dummy_clk << DATA_READ_DUMMY_S) |
+ (op->cmd.opcode << DATA_READ_CMD_S));
+
+ // read address
+ nfi_write32(snf, SNF_RD_CTL3, op_addr);
+
+ // Set read op_mode
+ if (op->data.buswidth == 4)
+ rd_mode = op->addr.buswidth == 4 ? DATA_READ_MODE_QUAD :
+ DATA_READ_MODE_X4;
+ else if (op->data.buswidth == 2)
+ rd_mode = op->addr.buswidth == 2 ? DATA_READ_MODE_DUAL :
+ DATA_READ_MODE_X2;
+ else
+ rd_mode = DATA_READ_MODE_X1;
+ rd_mode <<= DATA_READ_MODE_S;
+ nfi_rmw32(snf, SNF_MISC_CTL, DATA_READ_MODE,
+ rd_mode | DATARD_CUSTOM_EN);
+
+ // Set bytes to read
+ rd_bytes = (snf->nfi_cfg.spare_size + snf->caps->sector_size) *
+ snf->nfi_cfg.nsectors;
+ nfi_write32(snf, SNF_MISC_CTL2,
+ (rd_bytes << PROGRAM_LOAD_BYTE_NUM_S) | rd_bytes);
+
+ // NFI read prepare
+ nfi_write16(snf, NFI_CNFG,
+ (CNFG_OP_MODE_CUST << CNFG_OP_MODE_S) | CNFG_DMA_BURST_EN |
+ CNFG_READ_MODE | CNFG_DMA_MODE | op_mode);
+
+ nfi_write32(snf, NFI_CON, (snf->nfi_cfg.nsectors << CON_SEC_NUM_S));
+ nfi_write32(snf, NFI_STRADDR, (u32)snf->buf_dma);
+ if (op->data.ecc) {
+ snf->ecc_cfg.op = ECC_DECODE;
+ ret = mtk_ecc_enable(snf->ecc, &snf->ecc_cfg);
+ if (ret)
+ goto cleanup;
+ }
+ // Prepare for custom read interrupt
+ nfi_write32(snf, NFI_INTR_EN, NFI_IRQ_INTR_EN | NFI_IRQ_CUS_READ);
+ reinit_completion(&snf->op_done);
+
+ // Trigger NFI into custom mode
+ nfi_write16(snf, NFI_CMD, NFI_CMD_DUMMY_READ);
+
+ // Start DMA read
+ nfi_rmw32(snf, NFI_CON, 0, CON_BRD);
+ nfi_write16(snf, NFI_STRDATA, STR_DATA);
+
+ if (!wait_for_completion_timeout(
+ &snf->op_done, usecs_to_jiffies(SNFI_POLL_INTERVAL))) {
+ dev_err(snf->dev, "DMA timed out for reading from cache.\n");
+ ret = -ETIMEDOUT;
+ goto cleanup;
+ }
+
+ // Wait for BUS_SEC_CNTR returning expected value
+ ret = readl_poll_timeout(snf->nfi_base + NFI_BYTELEN, val,
+ BUS_SEC_CNTR(val) >= snf->nfi_cfg.nsectors, 0,
+ SNFI_POLL_INTERVAL);
+ if (ret) {
+ dev_err(snf->dev, "Timed out waiting for BUS_SEC_CNTR\n");
+ goto cleanup2;
+ }
+
+ // Wait for bus becoming idle
+ ret = readl_poll_timeout(snf->nfi_base + NFI_MASTERSTA, val,
+ !(val & snf->caps->mastersta_mask), 0,
+ SNFI_POLL_INTERVAL);
+ if (ret) {
+ dev_err(snf->dev, "Timed out waiting for bus becoming idle\n");
+ goto cleanup2;
+ }
+
+ if (op->data.ecc) {
+ ret = mtk_ecc_wait_done(snf->ecc, ECC_DECODE);
+ if (ret) {
+ dev_err(snf->dev, "wait ecc done timeout\n");
+ goto cleanup2;
+ }
+ // save status before disabling ecc
+ mtk_ecc_get_stats(snf->ecc, &snf->ecc_stats,
+ snf->nfi_cfg.nsectors);
+ }
+
+ if (snf->autofmt) {
+ mtk_snand_read_fdm(snf, snf->buf + snf->nfi_cfg.page_size);
+ if (snf->caps->bbm_swap) {
+ mtk_snand_bm_swap(snf);
+ mtk_snand_fdm_bm_swap(snf);
+ }
+ }
+
+ // copy data back
+ if (nfi_read32(snf, NFI_STA) & READ_EMPTY) {
+ memset(op->data.buf.in, 0xff, op->data.nbytes);
+ snf->ecc_stats.bitflips = 0;
+ snf->ecc_stats.failed = 0;
+ snf->ecc_stats.corrected = 0;
+ } else {
+ if (rd_offset < snf->buf_len) {
+ u32 cap_len = snf->buf_len - rd_offset;
+
+ if (op->data.nbytes < cap_len)
+ cap_len = op->data.nbytes;
+ memcpy(op->data.buf.in, snf->buf + rd_offset, cap_len);
+ }
+ }
+cleanup2:
+ if (op->data.ecc)
+ mtk_ecc_disable(snf->ecc);
+cleanup:
+ // Stop read
+ nfi_write32(snf, NFI_CON, 0);
+ nfi_write16(snf, NFI_CNFG, 0);
+
+ // Clear SNF done flag
+ nfi_rmw32(snf, SNF_STA_CTL1, 0, CUS_READ_DONE);
+ nfi_write32(snf, SNF_STA_CTL1, 0);
+
+ // Disable interrupt
+ nfi_read32(snf, NFI_INTR_STA);
+ nfi_write32(snf, NFI_INTR_EN, 0);
+
+ nfi_rmw32(snf, SNF_MISC_CTL, DATARD_CUSTOM_EN, 0);
+
+ return ret;
+}
+
+static int mtk_snand_write_page_cache(struct mtk_snand *snf,
+ const struct spi_mem_op *op)
+{
+ // the address part to be sent by the controller
+ u32 op_addr = op->addr.val;
+ // where to start copying data from bounce buffer
+ u32 wr_offset = 0;
+ u32 op_mode = 0;
+ int ret = 0;
+ u32 wr_mode = 0;
+ u32 wr_bytes, val;
+ size_t cap_len;
+
+ if (snf->autofmt) {
+ u32 last_bit;
+ u32 mask;
+
+ op_mode = CNFG_AUTO_FMT_EN;
+ if (op->data.ecc)
+ op_mode |= CNFG_HW_ECC_EN;
+
+ last_bit = fls(snf->nfi_cfg.page_size + snf->nfi_cfg.oob_size);
+ mask = (1 << last_bit) - 1;
+ wr_offset = op_addr & mask;
+ op_addr &= ~mask;
+ }
+ mtk_snand_mac_reset(snf);
+ mtk_nfi_reset(snf);
+
+ if (wr_offset)
+ memset(snf->buf, 0xff, wr_offset);
+
+ cap_len = snf->buf_len - wr_offset;
+ if (op->data.nbytes < cap_len)
+ cap_len = op->data.nbytes;
+ memcpy(snf->buf + wr_offset, op->data.buf.out, cap_len);
+ if (snf->autofmt && snf->caps->bbm_swap) {
+ mtk_snand_fdm_bm_swap(snf);
+ mtk_snand_bm_swap(snf);
+ }
+
+ // Command
+ nfi_write32(snf, SNF_PG_CTL1, (op->cmd.opcode << PG_LOAD_CMD_S));
+
+ // write address
+ nfi_write32(snf, SNF_PG_CTL2, op_addr);
+
+ // Set read op_mode
+ if (op->data.buswidth == 4)
+ wr_mode = PG_LOAD_X4_EN;
+
+ nfi_rmw32(snf, SNF_MISC_CTL, PG_LOAD_X4_EN,
+ wr_mode | PG_LOAD_CUSTOM_EN);
+
+ // Set bytes to write
+ wr_bytes = (snf->nfi_cfg.spare_size + snf->caps->sector_size) *
+ snf->nfi_cfg.nsectors;
+ nfi_write32(snf, SNF_MISC_CTL2,
+ (wr_bytes << PROGRAM_LOAD_BYTE_NUM_S) | wr_bytes);
+
+ // NFI write prepare
+ nfi_write16(snf, NFI_CNFG,
+ (CNFG_OP_MODE_PROGRAM << CNFG_OP_MODE_S) |
+ CNFG_DMA_BURST_EN | CNFG_DMA_MODE | op_mode);
+
+ nfi_write32(snf, NFI_CON, (snf->nfi_cfg.nsectors << CON_SEC_NUM_S));
+ nfi_write32(snf, NFI_STRADDR, (u32)snf->buf_dma);
+ if (op->data.ecc) {
+ snf->ecc_cfg.op = ECC_ENCODE;
+ ret = mtk_ecc_enable(snf->ecc, &snf->ecc_cfg);
+ if (ret)
+ goto cleanup;
+ }
+ // Prepare for custom write interrupt
+ nfi_write32(snf, NFI_INTR_EN, NFI_IRQ_INTR_EN | NFI_IRQ_CUS_PG);
+ reinit_completion(&snf->op_done);
+ ;
+
+ // Trigger NFI into custom mode
+ nfi_write16(snf, NFI_CMD, NFI_CMD_DUMMY_WRITE);
+
+ // Start DMA write
+ nfi_rmw32(snf, NFI_CON, 0, CON_BWR);
+ nfi_write16(snf, NFI_STRDATA, STR_DATA);
+
+ if (!wait_for_completion_timeout(
+ &snf->op_done, usecs_to_jiffies(SNFI_POLL_INTERVAL))) {
+ dev_err(snf->dev, "DMA timed out for program load.\n");
+ ret = -ETIMEDOUT;
+ goto cleanup;
+ }
+
+ // Wait for NFI_SEC_CNTR returning expected value
+ ret = readl_poll_timeout(snf->nfi_base + NFI_ADDRCNTR, val,
+ NFI_SEC_CNTR(val) >= snf->nfi_cfg.nsectors, 0,
+ SNFI_POLL_INTERVAL);
+ if (ret)
+ dev_err(snf->dev, "Timed out waiting for NFI_SEC_CNTR\n");
+
+ if (op->data.ecc)
+ mtk_ecc_disable(snf->ecc);
+cleanup:
+ // Stop write
+ nfi_write32(snf, NFI_CON, 0);
+ nfi_write16(snf, NFI_CNFG, 0);
+
+ // Clear SNF done flag
+ nfi_rmw32(snf, SNF_STA_CTL1, 0, CUS_PG_DONE);
+ nfi_write32(snf, SNF_STA_CTL1, 0);
+
+ // Disable interrupt
+ nfi_read32(snf, NFI_INTR_STA);
+ nfi_write32(snf, NFI_INTR_EN, 0);
+
+ nfi_rmw32(snf, SNF_MISC_CTL, PG_LOAD_CUSTOM_EN, 0);
+
+ return ret;
+}
+
+/**
+ * mtk_snand_is_page_ops() - check if the op is a controller supported page op.
+ * @op spi-mem op to check
+ *
+ * Check whether op can be executed with read_from_cache or program_load
+ * mode in the controller.
+ * This controller can execute typical Read From Cache and Program Load
+ * instructions found on SPI-NAND with 2-byte address.
+ * DTR and cmd buswidth & nbytes should be checked before calling this.
+ *
+ * Return: true if the op matches the instruction template
+ */
+static bool mtk_snand_is_page_ops(const struct spi_mem_op *op)
+{
+ if (op->addr.nbytes != 2)
+ return false;
+
+ if (op->addr.buswidth != 1 && op->addr.buswidth != 2 &&
+ op->addr.buswidth != 4)
+ return false;
+
+ // match read from page instructions
+ if (op->data.dir == SPI_MEM_DATA_IN) {
+ // check dummy cycle first
+ if (op->dummy.nbytes * BITS_PER_BYTE / op->dummy.buswidth >
+ DATA_READ_MAX_DUMMY)
+ return false;
+ // quad io / quad out
+ if ((op->addr.buswidth == 4 || op->addr.buswidth == 1) &&
+ op->data.buswidth == 4)
+ return true;
+
+ // dual io / dual out
+ if ((op->addr.buswidth == 2 || op->addr.buswidth == 1) &&
+ op->data.buswidth == 2)
+ return true;
+
+ // standard spi
+ if (op->addr.buswidth == 1 && op->data.buswidth == 1)
+ return true;
+ } else if (op->data.dir == SPI_MEM_DATA_OUT) {
+ // check dummy cycle first
+ if (op->dummy.nbytes)
+ return false;
+ // program load quad out
+ if (op->addr.buswidth == 1 && op->data.buswidth == 4)
+ return true;
+ // standard spi
+ if (op->addr.buswidth == 1 && op->data.buswidth == 1)
+ return true;
+ }
+ return false;
+}
+
+static bool mtk_snand_supports_op(struct spi_mem *mem,
+ const struct spi_mem_op *op)
+{
+ if (!spi_mem_default_supports_op(mem, op))
+ return false;
+ if (op->cmd.nbytes != 1 || op->cmd.buswidth != 1)
+ return false;
+ if (mtk_snand_is_page_ops(op))
+ return true;
+ return ((op->addr.nbytes == 0 || op->addr.buswidth == 1) &&
+ (op->dummy.nbytes == 0 || op->dummy.buswidth == 1) &&
+ (op->data.nbytes == 0 || op->data.buswidth == 1));
+}
+
+static int mtk_snand_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
+{
+ struct mtk_snand *ms = spi_controller_get_devdata(mem->spi->master);
+ // page ops transfer size must be exactly ((sector_size + spare_size) *
+ // nsectors). Limit the op size if the caller requests more than that.
+ // exec_op will read more than needed and discard the leftover if the
+ // caller requests less data.
+ if (mtk_snand_is_page_ops(op)) {
+ size_t l;
+ // skip adjust_op_size for page ops
+ if (ms->autofmt)
+ return 0;
+ l = ms->caps->sector_size + ms->nfi_cfg.spare_size;
+ l *= ms->nfi_cfg.nsectors;
+ if (op->data.nbytes > l)
+ op->data.nbytes = l;
+ } else {
+ size_t hl = op->cmd.nbytes + op->addr.nbytes + op->dummy.nbytes;
+
+ if (hl >= SNF_GPRAM_SIZE)
+ return -EOPNOTSUPP;
+ if (op->data.nbytes > SNF_GPRAM_SIZE - hl)
+ op->data.nbytes = SNF_GPRAM_SIZE - hl;
+ }
+ return 0;
+}
+
+static int mtk_snand_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+ struct mtk_snand *ms = spi_controller_get_devdata(mem->spi->master);
+
+ dev_dbg(ms->dev, "OP %02x ADDR %08llX@%d:%u DATA %d:%u", op->cmd.opcode,
+ op->addr.val, op->addr.buswidth, op->addr.nbytes,
+ op->data.buswidth, op->data.nbytes);
+ if (mtk_snand_is_page_ops(op)) {
+ if (op->data.dir == SPI_MEM_DATA_IN)
+ return mtk_snand_read_page_cache(ms, op);
+ else
+ return mtk_snand_write_page_cache(ms, op);
+ } else {
+ return mtk_snand_mac_io(ms, op);
+ }
+}
+
+static const struct spi_controller_mem_ops mtk_snand_mem_ops = {
+ .adjust_op_size = mtk_snand_adjust_op_size,
+ .supports_op = mtk_snand_supports_op,
+ .exec_op = mtk_snand_exec_op,
+};
+
+static const struct spi_controller_mem_caps mtk_snand_mem_caps = {
+ .ecc = true,
+};
+
+static irqreturn_t mtk_snand_irq(int irq, void *id)
+{
+ struct mtk_snand *snf = id;
+ uint32_t sta, ien;
+
+ sta = nfi_read32(snf, NFI_INTR_STA);
+ ien = nfi_read32(snf, NFI_INTR_EN);
+
+ if (!(sta & ien))
+ return IRQ_NONE;
+
+ nfi_write32(snf, NFI_INTR_EN, 0);
+ complete(&snf->op_done);
+ return IRQ_HANDLED;
+}
+
+static const struct of_device_id mtk_snand_ids[] = {
+ { .compatible = "mediatek,mt7622-snand", .data = &mt7622_snand_caps },
+ { .compatible = "mediatek,mt7629-snand", .data = &mt7629_snand_caps },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, mtk_snand_ids);
+
+static int mtk_snand_enable_clk(struct mtk_snand *ms)
+{
+ int ret;
+
+ ret = clk_prepare_enable(ms->nfi_clk);
+ if (ret) {
+ dev_err(ms->dev, "unable to enable nfi clk\n");
+ return ret;
+ }
+ ret = clk_prepare_enable(ms->pad_clk);
+ if (ret) {
+ dev_err(ms->dev, "unable to enable pad clk\n");
+ goto err1;
+ }
+ return 0;
+err1:
+ clk_disable_unprepare(ms->nfi_clk);
+ return ret;
+}
+
+static void mtk_snand_disable_clk(struct mtk_snand *ms)
+{
+ clk_disable_unprepare(ms->pad_clk);
+ clk_disable_unprepare(ms->nfi_clk);
+}
+
+static int mtk_snand_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ const struct of_device_id *dev_id;
+ struct spi_controller *ctlr;
+ struct mtk_snand *ms;
+ int ret;
+
+ dev_id = of_match_node(mtk_snand_ids, np);
+ if (!dev_id)
+ return -EINVAL;
+
+ ctlr = devm_spi_alloc_master(&pdev->dev, sizeof(*ms));
+ if (!ctlr)
+ return -ENOMEM;
+ platform_set_drvdata(pdev, ctlr);
+
+ ms = spi_controller_get_devdata(ctlr);
+
+ ms->ctlr = ctlr;
+ ms->caps = dev_id->data;
+
+ ms->ecc = of_mtk_ecc_get(np);
+ if (IS_ERR(ms->ecc))
+ return PTR_ERR(ms->ecc);
+ else if (!ms->ecc)
+ return -ENODEV;
+
+ ms->nfi_base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(ms->nfi_base)) {
+ ret = PTR_ERR(ms->nfi_base);
+ goto release_ecc;
+ }
+
+ ms->dev = &pdev->dev;
+
+ ms->nfi_clk = devm_clk_get(&pdev->dev, "nfi_clk");
+ if (IS_ERR(ms->nfi_clk)) {
+ ret = PTR_ERR(ms->nfi_clk);
+ dev_err(&pdev->dev, "unable to get nfi_clk, err = %d\n", ret);
+ goto release_ecc;
+ }
+
+ ms->pad_clk = devm_clk_get(&pdev->dev, "pad_clk");
+ if (IS_ERR(ms->pad_clk)) {
+ ret = PTR_ERR(ms->pad_clk);
+ dev_err(&pdev->dev, "unable to get pad_clk, err = %d\n", ret);
+ goto release_ecc;
+ }
+
+ ret = mtk_snand_enable_clk(ms);
+ if (ret)
+ goto release_ecc;
+
+ init_completion(&ms->op_done);
+
+ ms->irq = platform_get_irq(pdev, 0);
+ if (ms->irq < 0) {
+ ret = ms->irq;
+ goto disable_clk;
+ }
+ ret = devm_request_irq(ms->dev, ms->irq, mtk_snand_irq, 0x0,
+ "mtk-snand", ms);
+ if (ret) {
+ dev_err(ms->dev, "failed to request snfi irq\n");
+ goto disable_clk;
+ }
+
+ ret = dma_set_mask(ms->dev, DMA_BIT_MASK(32));
+ if (ret) {
+ dev_err(ms->dev, "failed to set dma mask\n");
+ goto disable_clk;
+ }
+
+ // setup an initial page format for ops matching page_cache_op template
+ // before ECC is called.
+ ret = mtk_snand_setup_pagefmt(ms, ms->caps->sector_size,
+ ms->caps->spare_sizes[0]);
+ if (ret) {
+ dev_err(ms->dev, "failed to set initial page format\n");
+ goto disable_clk;
+ }
+
+ // setup ECC engine
+ ms->ecc_eng.dev = &pdev->dev;
+ ms->ecc_eng.integration = NAND_ECC_ENGINE_INTEGRATION_PIPELINED;
+ ms->ecc_eng.ops = &mtk_snfi_ecc_engine_ops;
+ ms->ecc_eng.priv = ms;
+
+ ret = nand_ecc_register_on_host_hw_engine(&ms->ecc_eng);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register ecc engine.\n");
+ goto disable_clk;
+ }
+
+ ctlr->num_chipselect = 1;
+ ctlr->mem_ops = &mtk_snand_mem_ops;
+ ctlr->mem_caps = &mtk_snand_mem_caps;
+ ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
+ ctlr->mode_bits = SPI_RX_DUAL | SPI_RX_QUAD | SPI_TX_DUAL | SPI_TX_QUAD;
+ ctlr->dev.of_node = pdev->dev.of_node;
+ ret = spi_register_controller(ctlr);
+ if (ret) {
+ dev_err(&pdev->dev, "spi_register_controller failed.\n");
+ goto disable_clk;
+ }
+
+ return 0;
+disable_clk:
+ mtk_snand_disable_clk(ms);
+release_ecc:
+ mtk_ecc_release(ms->ecc);
+ return ret;
+}
+
+static int mtk_snand_remove(struct platform_device *pdev)
+{
+ struct spi_controller *ctlr = platform_get_drvdata(pdev);
+ struct mtk_snand *ms = spi_controller_get_devdata(ctlr);
+
+ spi_unregister_controller(ctlr);
+ mtk_snand_disable_clk(ms);
+ mtk_ecc_release(ms->ecc);
+ return 0;
+}
+
+static struct platform_driver mtk_snand_driver = {
+ .probe = mtk_snand_probe,
+ .remove = mtk_snand_remove,
+ .driver = {
+ .name = "mtk-snand",
+ .of_match_table = mtk_snand_ids,
+ },
+};
+
+module_platform_driver(mtk_snand_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Chuanhong Guo <gch981213@gmail.com>");
+MODULE_DESCRIPTION("MeidaTek SPI-NAND Flash Controller Driver");
This driver implements support for the SPI-NAND mode of MTK NAND Flash Interface as a SPI-MEM controller with piplined ECC capability. Signed-off-by: Chuanhong Guo <gch981213@gmail.com> --- Change since v1: fix CI warnings drivers/spi/Kconfig | 10 + drivers/spi/Makefile | 1 + drivers/spi/spi-mtk-snfi.c | 1351 ++++++++++++++++++++++++++++++++++++ 3 files changed, 1362 insertions(+) create mode 100644 drivers/spi/spi-mtk-snfi.c