new file mode 100644
@@ -0,0 +1,64 @@
+/*
+ * xen/arch/arm/include/asm/imx-lpuart.h
+ *
+ * Common constant definition between early printk and the LPUART driver
+ *
+ * Peng Fan <peng.fan@nxp.com>
+ * Copyright 2022 NXP
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __ASM_ARM_IMX_LPUART_H__
+#define __ASM_ARM_IMX_LPUART_H__
+
+/* 32-bit register definition */
+#define UARTBAUD (0x10)
+#define UARTSTAT (0x14)
+#define UARTCTRL (0x18)
+#define UARTDATA (0x1C)
+#define UARTMATCH (0x20)
+#define UARTMODIR (0x24)
+#define UARTFIFO (0x28)
+#define UARTWATER (0x2c)
+
+#define UARTSTAT_TDRE BIT(23, UL)
+#define UARTSTAT_TC BIT(22, UL)
+#define UARTSTAT_RDRF BIT(21, UL)
+#define UARTSTAT_OR BIT(19, UL)
+
+#define UARTBAUD_OSR_SHIFT (24)
+#define UARTBAUD_OSR_MASK (0x1f)
+#define UARTBAUD_SBR_MASK (0x1fff)
+#define UARTBAUD_BOTHEDGE (0x00020000)
+#define UARTBAUD_TDMAE (0x00800000)
+#define UARTBAUD_RDMAE (0x00200000)
+
+#define UARTCTRL_TIE BIT(23, UL)
+#define UARTCTRL_TCIE BIT(22, UL)
+#define UARTCTRL_RIE BIT(21, UL)
+#define UARTCTRL_ILIE BIT(20, UL)
+#define UARTCTRL_TE BIT(19, UL)
+#define UARTCTRL_RE BIT(18, UL)
+#define UARTCTRL_M BIT(4, UL)
+
+#define UARTWATER_RXCNT_OFF 24
+
+#endif /* __ASM_ARM_IMX_LPUART_H__ */
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */
@@ -13,6 +13,13 @@ config HAS_CADENCE_UART
This selects the Xilinx Zynq Cadence UART. If you have a Xilinx Zynq
based board, say Y.
+config HAS_IMX_LPUART
+ bool "i.MX LPUART driver"
+ default y
+ depends on ARM_64
+ help
+ This selects the i.MX LPUART. If you have i.MX8QM based board, say Y.
+
config HAS_MVEBU
bool "Marvell MVEBU UART driver"
default y
@@ -8,6 +8,7 @@ obj-$(CONFIG_HAS_MVEBU) += mvebu-uart.o
obj-$(CONFIG_HAS_OMAP) += omap-uart.o
obj-$(CONFIG_HAS_SCIF) += scif-uart.o
obj-$(CONFIG_HAS_EHCI) += ehci-dbgp.o
+obj-$(CONFIG_HAS_IMX_LPUART) += imx-lpuart.o
obj-$(CONFIG_ARM) += arm-uart.o
obj-y += serial.o
obj-$(CONFIG_XEN_GUEST) += xen_pv_console.o
new file mode 100644
@@ -0,0 +1,276 @@
+/*
+ * xen/drivers/char/imx-lpuart.c
+ *
+ * Driver for i.MX LPUART.
+ *
+ * Peng Fan <peng.fan@nxp.com>
+ * Copyright 2022 NXP
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <xen/errno.h>
+#include <xen/init.h>
+#include <xen/irq.h>
+#include <xen/mm.h>
+#include <xen/serial.h>
+#include <asm/device.h>
+#include <asm/imx-lpuart.h>
+#include <asm/io.h>
+
+#define imx_lpuart_read(uart, off) readl((uart)->regs + off)
+#define imx_lpuart_write(uart, off, val) writel((val), (uart)->regs + off)
+
+static struct imx_lpuart {
+ uint32_t baud, clock_hz, data_bits, parity, stop_bits, fifo_size;
+ uint32_t irq;
+ char __iomem *regs;
+ struct irqaction irqaction;
+ struct vuart_info vuart;
+} imx8_com;
+
+static void imx_lpuart_interrupt(int irq, void *data,
+ struct cpu_user_regs *regs)
+{
+ struct serial_port *port = data;
+ struct imx_lpuart *uart = port->uart;
+ uint32_t sts, rxcnt;
+
+ sts = imx_lpuart_read(uart, UARTSTAT);
+ rxcnt = imx_lpuart_read(uart, UARTWATER) >> UARTWATER_RXCNT_OFF;
+
+ if ( (sts & UARTSTAT_RDRF) || (rxcnt > 0) )
+ serial_rx_interrupt(port, regs);
+
+ if ( sts & UARTSTAT_TDRE )
+ serial_tx_interrupt(port, regs);
+
+ imx_lpuart_write(uart, UARTSTAT, sts);
+}
+
+static void __init imx_lpuart_init_preirq(struct serial_port *port)
+{
+ struct imx_lpuart *uart = port->uart;
+ uint32_t ctrl, old_ctrl, bd;
+
+ old_ctrl = imx_lpuart_read(uart, UARTCTRL);
+ ctrl = (old_ctrl & ~UARTCTRL_M) | UARTCTRL_TE | UARTCTRL_RE;
+ bd = imx_lpuart_read(uart, UARTBAUD);
+
+ while ( !(imx_lpuart_read(uart, UARTSTAT) & UARTSTAT_TC) )
+ cpu_relax();
+
+ /* Disable transmit and receive */
+ imx_lpuart_write(uart, UARTCTRL, old_ctrl & ~(UARTCTRL_TE | UARTCTRL_RE));
+
+ /* Reuse firmware baudrate settings, only disable DMA here */
+ bd &= ~(UARTBAUD_TDMAE | UARTBAUD_RDMAE);
+
+ imx_lpuart_write(uart, UARTMODIR, 0);
+ imx_lpuart_write(uart, UARTBAUD, bd);
+ imx_lpuart_write(uart, UARTCTRL, ctrl);
+}
+
+static void __init imx_lpuart_init_postirq(struct serial_port *port)
+{
+ struct imx_lpuart *uart = port->uart;
+ uint32_t temp;
+
+ uart->irqaction.handler = imx_lpuart_interrupt;
+ uart->irqaction.name = "imx_lpuart";
+ uart->irqaction.dev_id = port;
+
+ if ( setup_irq(uart->irq, 0, &uart->irqaction) != 0 )
+ {
+ dprintk(XENLOG_ERR, "Failed to allocate imx_lpuart IRQ %d\n",
+ uart->irq);
+ return;
+ }
+
+ /* Enable interrupts */
+ temp = imx_lpuart_read(uart, UARTCTRL);
+ temp |= (UARTCTRL_RIE | UARTCTRL_TIE);
+ temp |= UARTCTRL_ILIE;
+ imx_lpuart_write(uart, UARTCTRL, temp);
+}
+
+static void imx_lpuart_suspend(struct serial_port *port)
+{
+ BUG();
+}
+
+static void imx_lpuart_resume(struct serial_port *port)
+{
+ BUG();
+}
+
+static int imx_lpuart_tx_ready(struct serial_port *port)
+{
+ struct imx_lpuart *uart = port->uart;
+
+ return imx_lpuart_read(uart, UARTSTAT) & UARTSTAT_TC;
+}
+
+static void imx_lpuart_putc(struct serial_port *port, char c)
+{
+ struct imx_lpuart *uart = port->uart;
+
+ while ( !(imx_lpuart_read(uart, UARTSTAT) & UARTSTAT_TDRE) )
+ cpu_relax();
+
+ imx_lpuart_write(uart, UARTDATA, c);
+}
+
+static int imx_lpuart_getc(struct serial_port *port, char *pc)
+{
+ struct imx_lpuart *uart = port->uart;
+ int ch;
+
+ while ( !(imx_lpuart_read(uart, UARTSTAT) & UARTSTAT_RDRF) )
+ return 0;
+
+ ch = imx_lpuart_read(uart, UARTDATA);
+ *pc = ch & 0xff;
+
+ if ( imx_lpuart_read(uart, UARTSTAT) & UARTSTAT_OR )
+ imx_lpuart_write(uart, UARTSTAT, UARTSTAT_OR);
+
+ return 1;
+}
+
+static int __init imx_lpuart_irq(struct serial_port *port)
+{
+ struct imx_lpuart *uart = port->uart;
+
+ return ((uart->irq > 0) ? uart->irq : -1);
+}
+
+static const struct vuart_info *imx_lpuart_vuart_info(struct serial_port *port)
+{
+ struct imx_lpuart *uart = port->uart;
+
+ return &uart->vuart;
+}
+
+static void imx_lpuart_start_tx(struct serial_port *port)
+{
+ struct imx_lpuart *uart = port->uart;
+ uint32_t temp;
+
+ temp = imx_lpuart_read(uart, UARTSTAT);
+ /* Wait until empty */
+ while ( !(temp & UARTSTAT_TDRE) )
+ cpu_relax();
+
+ temp = imx_lpuart_read(uart, UARTCTRL);
+ imx_lpuart_write(uart, UARTCTRL, (temp | UARTCTRL_TIE));
+}
+
+static void imx_lpuart_stop_tx(struct serial_port *port)
+{
+ struct imx_lpuart *uart = port->uart;
+ uint32_t temp;
+
+ temp = imx_lpuart_read(uart, UARTCTRL);
+ temp &= ~(UARTCTRL_TIE | UARTCTRL_TCIE);
+ imx_lpuart_write(uart, UARTCTRL, temp);
+}
+
+static struct uart_driver __read_mostly imx_lpuart_driver = {
+ .init_preirq = imx_lpuart_init_preirq,
+ .init_postirq = imx_lpuart_init_postirq,
+ .endboot = NULL,
+ .suspend = imx_lpuart_suspend,
+ .resume = imx_lpuart_resume,
+ .tx_ready = imx_lpuart_tx_ready,
+ .putc = imx_lpuart_putc,
+ .getc = imx_lpuart_getc,
+ .irq = imx_lpuart_irq,
+ .start_tx = imx_lpuart_start_tx,
+ .stop_tx = imx_lpuart_stop_tx,
+ .vuart_info = imx_lpuart_vuart_info,
+};
+
+static int __init imx_lpuart_init(struct dt_device_node *dev,
+ const void *data)
+{
+ const char *config = data;
+ struct imx_lpuart *uart;
+ int res;
+ u64 addr, size;
+
+ if ( strcmp(config, "") )
+ printk("WARNING: UART configuration is not supported\n");
+
+ uart = &imx8_com;
+
+ uart->baud = 115200;
+ uart->data_bits = 8;
+ uart->parity = 0;
+ uart->stop_bits = 1;
+
+ res = dt_device_get_address(dev, 0, &addr, &size);
+ if ( res )
+ {
+ printk("imx8-lpuart: Unable to retrieve the base"
+ " address of the UART\n");
+ return res;
+ }
+
+ res = platform_get_irq(dev, 0);
+ if ( res < 0 )
+ {
+ printk("imx8-lpuart: Unable to retrieve the IRQ\n");
+ return -EINVAL;
+ }
+ uart->irq = res;
+
+ uart->regs = ioremap_nocache(addr, size);
+ if ( !uart->regs )
+ {
+ printk("imx8-lpuart: Unable to map the UART memory\n");
+ return -ENOMEM;
+ }
+
+ uart->vuart.base_addr = addr;
+ uart->vuart.size = size;
+ uart->vuart.data_off = UARTDATA;
+ /* tmp from uboot */
+ uart->vuart.status_off = UARTSTAT;
+ uart->vuart.status = UARTSTAT_TDRE;
+
+ /* Register with generic serial driver */
+ serial_register_uart(SERHND_DTUART, &imx_lpuart_driver, uart);
+
+ dt_device_set_used_by(dev, DOMID_XEN);
+
+ return 0;
+}
+
+static const struct dt_device_match imx_lpuart_dt_compat[] __initconst =
+{
+ DT_MATCH_COMPATIBLE("fsl,imx8qm-lpuart"),
+ { /* sentinel */ },
+};
+
+DT_DEVICE_START(imx_lpuart, "i.MX LPUART", DEVICE_SERIAL)
+ .dt_match = imx_lpuart_dt_compat,
+ .init = imx_lpuart_init,
+DT_DEVICE_END
+
+/*
+ * Local variables:
+ * mode: C
+ * c-file-style: "BSD"
+ * c-basic-offset: 4
+ * indent-tabs-mode: nil
+ * End:
+ */