| Message ID | 20220506132416.273965-1-marcel@ziswiler.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | ARM: dts: imx6ull-colibri: device tree improvements | expand |
On Fri, May 06, 2022 at 03:24:03PM +0200, Marcel Ziswiler wrote: > From: Marcel Ziswiler <marcel.ziswiler@toradex.com> > > > This is a general update of the Colibri iMX6ULL device tree files. > > The Toradex Colibri family is composed of a SoM that can be plugged on > various carrier boards, with carrier boards allowing multiple optional > accessories (e.g. display, camera, ...). > > The device tree sources are structured into a SoM dtsi and a carrier dts > which then includes the SoM dtsi. The SoM dtsi defines and enables the > functionality self-contained on the SoM and prepares for the > functionality provided by the carrier HW or accessories so that the > carrier dts then can enable or amend nodes provided. Accessories are > enabled in overlays depending on HW configuration. > > Please find the following colibri-imx6ull device trees improvements: > > - MMC/SD > The original Colibri specification only defined 3.3 volt TTL signaling > and relied on external on-carrier pull-ups for the SD_DATA[0..3] lines. > The latest carrier boards like Iris V2 on the other hand are now UHS-I > compliant by leaving such external on-carrier pull-ups away relying on > module- or even SoC-level ones which pull up to resp. signaling voltage. > In such cases, the carrier board-level device tree may explicitly delete > the no-1-8-v property to enable full UHS-I support. > Also, fix SD/MMC regulator for the carrier boards using UHS-I modes. > > - FEC > Provide a proper phy-supply for the FEC, actually switched by the 50 Mhz > RMII interface clock using a regulator-fixed-clock that is now properly > stated. The reference commit for such regulator can be found at commit > 8959e5324485 ("regulator: fixed: add possibility to enable by clock"). > > - I2C > Switched on 22 kOhm pull-ups and lower the I2C frequency to 40 kHz to > get more reliable communication. > > - Atmel Touchscreen > The Toradex 7" Capacitive and 10" LVDS touch screens are Atmel MXT > peripherals available on the I2C bus for touchscreen events. Add > atmel_mxt_ts node to the module-level device tree. Also, provide pinmux > configuration for the INT/RST inputs from SODIMM pins 106/107 for most > carrier boards or an external touchscreen adapter inputs configured to > SODIMM pins 28/30. > > Changes in v3: > - Fixed reset GPIO polarity in-line with the following upstream commit: > feedaacdadfc ("Input: atmel_mxt_ts - fix up inverted RESET handler") > - Fixed comment using more common SODIMM followed by number naming. > - Replaced underscores by dashes in GPIO hog node names. > - Added more LVDS specific GPIO hogs in-line with other modules. > - Re-based on top of Shawn's imx/dt branch. > - Dropped [PATCH v2 08/14] dt-bindings: arm: fsl: add > toradex,colibri-imx6ull which already got applied by Shawn. Thanks! > > Changes in v2: > - Fixed pinctrl node names as suggested by Shawn. > - Fix alphabetical node order as suggested by Shawn. > - Dropped [PATCH v1 02/14] ARM: dts: imx6ull-colibri: fix vqmmc > regulator which already got applied by Shawn. Thanks! > - New commit with pinctrl node name improvements as suggested by Shawn. > > Denys Drozdov (4): > ARM: dts: imx6ull-colibri: add touchscreen device nodes > ARM: dts: imx6ull-colibri: update device trees to support overlays > ARM: dts: imx6ull-colibri: add support for toradex iris carrier boards > ARM: dts: imx6ull-colibri: add support for toradex aster carrier > boards > > Marcel Ziswiler (4): > ARM: dts: imx6ull-colibri: fix nand bch geometry > ARM: dts: imx6ull-colibri: add/update some comments > ARM: dts: imx6ull-colibri: move gpio-keys node to som dtsi > ARM: dts: imx6ull-colibri: improve pinctrl node names > > Max Krummenacher (1): > ARM: dts: imx6ull-colibri: change touch i2c parameters > > Oleksandr Suvorov (1): > ARM: dts: imx6ull-colibri: add gpio-line-names > > Philippe Schenker (3): > ARM: dts: imx6ull-colibri: use pull-down for adc pins > ARM: dts: imx6ull-colibri: add phy-supply to fec > ARM: dts: imx6ull-colibri: update usdhc1 pixmux and signaling Applied all, thanks!
From: Marcel Ziswiler <marcel.ziswiler@toradex.com> This is a general update of the Colibri iMX6ULL device tree files. The Toradex Colibri family is composed of a SoM that can be plugged on various carrier boards, with carrier boards allowing multiple optional accessories (e.g. display, camera, ...). The device tree sources are structured into a SoM dtsi and a carrier dts which then includes the SoM dtsi. The SoM dtsi defines and enables the functionality self-contained on the SoM and prepares for the functionality provided by the carrier HW or accessories so that the carrier dts then can enable or amend nodes provided. Accessories are enabled in overlays depending on HW configuration. Please find the following colibri-imx6ull device trees improvements: - MMC/SD The original Colibri specification only defined 3.3 volt TTL signaling and relied on external on-carrier pull-ups for the SD_DATA[0..3] lines. The latest carrier boards like Iris V2 on the other hand are now UHS-I compliant by leaving such external on-carrier pull-ups away relying on module- or even SoC-level ones which pull up to resp. signaling voltage. In such cases, the carrier board-level device tree may explicitly delete the no-1-8-v property to enable full UHS-I support. Also, fix SD/MMC regulator for the carrier boards using UHS-I modes. - FEC Provide a proper phy-supply for the FEC, actually switched by the 50 Mhz RMII interface clock using a regulator-fixed-clock that is now properly stated. The reference commit for such regulator can be found at commit 8959e5324485 ("regulator: fixed: add possibility to enable by clock"). - I2C Switched on 22 kOhm pull-ups and lower the I2C frequency to 40 kHz to get more reliable communication. - Atmel Touchscreen The Toradex 7" Capacitive and 10" LVDS touch screens are Atmel MXT peripherals available on the I2C bus for touchscreen events. Add atmel_mxt_ts node to the module-level device tree. Also, provide pinmux configuration for the INT/RST inputs from SODIMM pins 106/107 for most carrier boards or an external touchscreen adapter inputs configured to SODIMM pins 28/30. Changes in v3: - Fixed reset GPIO polarity in-line with the following upstream commit: feedaacdadfc ("Input: atmel_mxt_ts - fix up inverted RESET handler") - Fixed comment using more common SODIMM followed by number naming. - Replaced underscores by dashes in GPIO hog node names. - Added more LVDS specific GPIO hogs in-line with other modules. - Re-based on top of Shawn's imx/dt branch. - Dropped [PATCH v2 08/14] dt-bindings: arm: fsl: add toradex,colibri-imx6ull which already got applied by Shawn. Thanks! Changes in v2: - Fixed pinctrl node names as suggested by Shawn. - Fix alphabetical node order as suggested by Shawn. - Dropped [PATCH v1 02/14] ARM: dts: imx6ull-colibri: fix vqmmc regulator which already got applied by Shawn. Thanks! - New commit with pinctrl node name improvements as suggested by Shawn. Denys Drozdov (4): ARM: dts: imx6ull-colibri: add touchscreen device nodes ARM: dts: imx6ull-colibri: update device trees to support overlays ARM: dts: imx6ull-colibri: add support for toradex iris carrier boards ARM: dts: imx6ull-colibri: add support for toradex aster carrier boards Marcel Ziswiler (4): ARM: dts: imx6ull-colibri: fix nand bch geometry ARM: dts: imx6ull-colibri: add/update some comments ARM: dts: imx6ull-colibri: move gpio-keys node to som dtsi ARM: dts: imx6ull-colibri: improve pinctrl node names Max Krummenacher (1): ARM: dts: imx6ull-colibri: change touch i2c parameters Oleksandr Suvorov (1): ARM: dts: imx6ull-colibri: add gpio-line-names Philippe Schenker (3): ARM: dts: imx6ull-colibri: use pull-down for adc pins ARM: dts: imx6ull-colibri: add phy-supply to fec ARM: dts: imx6ull-colibri: update usdhc1 pixmux and signaling arch/arm/boot/dts/Makefile | 9 + arch/arm/boot/dts/imx6ull-colibri-aster.dts | 20 ++ arch/arm/boot/dts/imx6ull-colibri-aster.dtsi | 145 +++++++++ .../boot/dts/imx6ull-colibri-emmc-aster.dts | 17 ++ .../boot/dts/imx6ull-colibri-emmc-iris-v2.dts | 17 ++ .../boot/dts/imx6ull-colibri-emmc-iris.dts | 17 ++ .../dts/imx6ull-colibri-emmc-nonwifi.dtsi | 8 +- arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts | 6 +- .../arm/boot/dts/imx6ull-colibri-eval-v3.dtsi | 63 +--- arch/arm/boot/dts/imx6ull-colibri-iris-v2.dts | 65 ++++ .../arm/boot/dts/imx6ull-colibri-iris-v2.dtsi | 27 ++ arch/arm/boot/dts/imx6ull-colibri-iris.dts | 20 ++ arch/arm/boot/dts/imx6ull-colibri-iris.dtsi | 132 ++++++++ .../arm/boot/dts/imx6ull-colibri-nonwifi.dtsi | 145 ++++++++- .../boot/dts/imx6ull-colibri-wifi-aster.dts | 20 ++ .../boot/dts/imx6ull-colibri-wifi-eval-v3.dts | 4 +- .../boot/dts/imx6ull-colibri-wifi-iris-v2.dts | 65 ++++ .../boot/dts/imx6ull-colibri-wifi-iris.dts | 20 ++ arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi | 144 ++++++++- arch/arm/boot/dts/imx6ull-colibri.dtsi | 285 ++++++++++++------ 20 files changed, 1065 insertions(+), 164 deletions(-) create mode 100644 arch/arm/boot/dts/imx6ull-colibri-aster.dts create mode 100644 arch/arm/boot/dts/imx6ull-colibri-aster.dtsi create mode 100644 arch/arm/boot/dts/imx6ull-colibri-emmc-aster.dts create mode 100644 arch/arm/boot/dts/imx6ull-colibri-emmc-iris-v2.dts create mode 100644 arch/arm/boot/dts/imx6ull-colibri-emmc-iris.dts create mode 100644 arch/arm/boot/dts/imx6ull-colibri-iris-v2.dts create mode 100644 arch/arm/boot/dts/imx6ull-colibri-iris-v2.dtsi create mode 100644 arch/arm/boot/dts/imx6ull-colibri-iris.dts create mode 100644 arch/arm/boot/dts/imx6ull-colibri-iris.dtsi create mode 100644 arch/arm/boot/dts/imx6ull-colibri-wifi-aster.dts create mode 100644 arch/arm/boot/dts/imx6ull-colibri-wifi-iris-v2.dts create mode 100644 arch/arm/boot/dts/imx6ull-colibri-wifi-iris.dts