diff mbox series

[06/12] dt-bindings: remoteproc: qcom,adsp: use GIC_SPI defines in example

Message ID 20220512100006.99695-7-krzysztof.kozlowski@linaro.org (mailing list archive)
State Superseded
Headers show
Series dt-bindings: remoteproc: qcom: cleanups and improvements | expand

Commit Message

Krzysztof Kozlowski May 12, 2022, 10 a.m. UTC
Use GIC_SPI defines instead of raw value in the DTS example.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

Comments

Rob Herring May 13, 2022, 12:33 p.m. UTC | #1
On Thu, 12 May 2022 12:00:00 +0200, Krzysztof Kozlowski wrote:
> Use GIC_SPI defines instead of raw value in the DTS example.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
>  Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml | 5 +++--
>  1 file changed, 3 insertions(+), 2 deletions(-)
> 

Running 'make dtbs_check' with the schema in this patch gives the
following warnings. Consider if they are expected or the schema is
incorrect. These may not be new warnings.

Note that it is not yet a requirement to have 0 warnings for dtbs_check.
This will change in the future.

Full log is available here: https://patchwork.ozlabs.org/patch/


remoteproc@b00000: qcom,halt-regs:0: [28, 102404] is too short
	arch/arm64/boot/dts/qcom/qcs404-evb-1000.dtb
	arch/arm64/boot/dts/qcom/qcs404-evb-4000.dtb
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
index e3a193299c4a..d04de60ae017 100644
--- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.yaml
@@ -575,11 +575,12 @@  allOf:
 examples:
   - |
     #include <dt-bindings/clock/qcom,rpmcc.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
     #include <dt-bindings/interrupt-controller/irq.h>
     adsp {
         compatible = "qcom,msm8974-adsp-pil";
 
-        interrupts-extended = <&intc 0 162 IRQ_TYPE_EDGE_RISING>,
+        interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
                       <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
                       <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
                       <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
@@ -601,7 +602,7 @@  examples:
         qcom,smem-state-names = "stop";
 
         smd-edge {
-            interrupts = <0 156 IRQ_TYPE_EDGE_RISING>;
+            interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
 
             qcom,ipc = <&apcs 8 8>;
             qcom,smd-edge = <1>;