@@ -1922,6 +1922,17 @@ config RTC_DRV_ASPEED
This driver can also be built as a module, if so, the module
will be called "rtc-aspeed".
+config RTC_DRV_TI_K3
+ tristate "TI K3 RTC"
+ depends on ARCH_K3 || COMPILE_TEST
+ select REGMAP_MMIO
+ help
+ If you say yes here you get support for the Texas Instruments's
+ Real Time Clock for K3 architecture.
+
+ This driver can also be built as a module, if so, the module
+ will be called "rtc-ti-k3".
+
comment "HID Sensor RTC drivers"
config RTC_DRV_HID_SENSOR_TIME
@@ -171,6 +171,7 @@ obj-$(CONFIG_RTC_DRV_SUNPLUS) += rtc-sunplus.o
obj-$(CONFIG_RTC_DRV_SUNXI) += rtc-sunxi.o
obj-$(CONFIG_RTC_DRV_TEGRA) += rtc-tegra.o
obj-$(CONFIG_RTC_DRV_TEST) += rtc-test.o
+obj-$(CONFIG_RTC_DRV_TI_K3) += rtc-ti-k3.o
obj-$(CONFIG_RTC_DRV_TPS6586X) += rtc-tps6586x.o
obj-$(CONFIG_RTC_DRV_TPS65910) += rtc-tps65910.o
obj-$(CONFIG_RTC_DRV_TWL4030) += rtc-twl.o
new file mode 100644
@@ -0,0 +1,695 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Texas Instruments K3 RTC driver
+ *
+ * Copyright (C) 2021-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#define dev_fmt(fmt) "%s: " fmt, __func__
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/rtc.h>
+
+/* Registers */
+#define REG_K3RTC_S_CNT_LSW 0x08
+#define REG_K3RTC_S_CNT_MSW 0x0c
+#define REG_K3RTC_COMP 0x10
+#define REG_K3RTC_ON_OFF_S_CNT_LSW 0x20
+#define REG_K3RTC_ON_OFF_S_CNT_MSW 0x24
+#define REG_K3RTC_SCRATCH0 0x30
+#define REG_K3RTC_SCRATCH7 0x4c
+#define REG_K3RTC_GENERAL_CTL 0x50
+#define REG_K3RTC_IRQSTATUS_RAW_SYS 0x54
+#define REG_K3RTC_IRQSTATUS_SYS 0x58
+#define REG_K3RTC_IRQENABLE_SET_SYS 0x5c
+#define REG_K3RTC_IRQENABLE_CLR_SYS 0x60
+#define REG_K3RTC_SYNCPEND 0x68
+#define REG_K3RTC_KICK0 0x70
+#define REG_K3RTC_KICK1 0x74
+
+/* Freeze when lsw is read and unfreeze when msw is read */
+#define K3RTC_CNT_FMODE_S_CNT_VALUE (0x2 << 24)
+
+/* Magic values for lock/unlock */
+#define K3RTC_KICK0_UNLOCK_VALUE 0x83e70b13
+#define K3RTC_KICK1_UNLOCK_VALUE 0x95a4f1e0
+
+/* Multiplier for ppb conversions */
+#define K3RTC_PPB_MULT (1000000000LL)
+/* Min and max values supported with 'offset' interface (swapped sign) */
+#define K3RTC_MIN_OFFSET (-277761)
+#define K3RTC_MAX_OFFSET (277778)
+
+/**
+ * struct ti_k3_rtc_soc_data - Private of compatible data for ti-k3-rtc
+ * @unlock_irq_erratum: Has erratum for unlock infinite IRQs (erratum i2327)
+ */
+struct ti_k3_rtc_soc_data {
+ const bool unlock_irq_erratum;
+};
+
+static const struct regmap_config ti_k3_rtc_regmap_config = {
+ .name = "peripheral-registers",
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = REG_K3RTC_KICK1,
+};
+
+enum ti_k3_rtc_fields {
+ K3RTC_KICK0,
+ K3RTC_KICK1,
+ K3RTC_S_CNT_LSW,
+ K3RTC_S_CNT_MSW,
+ K3RTC_O32K_OSC_DEP_EN,
+ K3RTC_UNLOCK,
+ K3RTC_CNT_FMODE,
+ K3RTC_PEND,
+ K3RTC_RELOAD_FROM_BBD,
+ K3RTC_COMP,
+
+ K3RTC_ALM_S_CNT_LSW,
+ K3RTC_ALM_S_CNT_MSW,
+ K3RTC_IRQ_STATUS_RAW,
+ K3RTC_IRQ_STATUS,
+ K3RTC_IRQ_ENABLE_SET,
+ K3RTC_IRQ_ENABLE_CLR,
+
+ K3RTC_IRQ_STATUS_ALT,
+ K3RTC_IRQ_ENABLE_CLR_ALT,
+
+ K3_RTC_MAX_FIELDS
+};
+
+static const struct reg_field ti_rtc_reg_fields[] = {
+ [K3RTC_KICK0] = REG_FIELD(REG_K3RTC_KICK0, 0, 31),
+ [K3RTC_KICK1] = REG_FIELD(REG_K3RTC_KICK1, 0, 31),
+ [K3RTC_S_CNT_LSW] = REG_FIELD(REG_K3RTC_S_CNT_LSW, 0, 31),
+ [K3RTC_S_CNT_MSW] = REG_FIELD(REG_K3RTC_S_CNT_MSW, 0, 15),
+ [K3RTC_O32K_OSC_DEP_EN] = REG_FIELD(REG_K3RTC_GENERAL_CTL, 21, 21),
+ [K3RTC_UNLOCK] = REG_FIELD(REG_K3RTC_GENERAL_CTL, 23, 23),
+ [K3RTC_CNT_FMODE] = REG_FIELD(REG_K3RTC_GENERAL_CTL, 24, 25),
+ [K3RTC_PEND] = REG_FIELD(REG_K3RTC_SYNCPEND, 0, 1),
+ [K3RTC_RELOAD_FROM_BBD] = REG_FIELD(REG_K3RTC_SYNCPEND, 31, 31),
+ [K3RTC_COMP] = REG_FIELD(REG_K3RTC_COMP, 0, 31),
+
+ /* We use on to off as alarm trigger */
+ [K3RTC_ALM_S_CNT_LSW] = REG_FIELD(REG_K3RTC_ON_OFF_S_CNT_LSW, 0, 31),
+ [K3RTC_ALM_S_CNT_MSW] = REG_FIELD(REG_K3RTC_ON_OFF_S_CNT_MSW, 0, 15),
+ [K3RTC_IRQ_STATUS_RAW] = REG_FIELD(REG_K3RTC_IRQSTATUS_RAW_SYS, 0, 0),
+ [K3RTC_IRQ_STATUS] = REG_FIELD(REG_K3RTC_IRQSTATUS_SYS, 0, 0),
+ [K3RTC_IRQ_ENABLE_SET] = REG_FIELD(REG_K3RTC_IRQENABLE_SET_SYS, 0, 0),
+ [K3RTC_IRQ_ENABLE_CLR] = REG_FIELD(REG_K3RTC_IRQENABLE_CLR_SYS, 0, 0),
+ /* Off to on is alternate */
+ [K3RTC_IRQ_STATUS_ALT] = REG_FIELD(REG_K3RTC_IRQSTATUS_SYS, 1, 1),
+ [K3RTC_IRQ_ENABLE_CLR_ALT] = REG_FIELD(REG_K3RTC_IRQENABLE_CLR_SYS, 1, 1),
+};
+
+/**
+ * struct ti_k3_rtc - Private data for ti-k3-rtc
+ * @irq: IRQ
+ * @sync_timeout_us: data sync timeout period in uSec
+ * @rate_32k: 32k clock rate in Hz
+ * @rtc_dev: rtc device
+ * @regmap: rtc mmio regmap
+ * @r_fields: rtc register fields
+ * @soc: SoC compatible match data
+ */
+struct ti_k3_rtc {
+ unsigned int irq;
+ u32 sync_timeout_us;
+ unsigned long rate_32k;
+ struct rtc_device *rtc_dev;
+ struct regmap *regmap;
+ struct regmap_field *r_fields[K3_RTC_MAX_FIELDS];
+ const struct ti_k3_rtc_soc_data *soc;
+};
+
+static int k3rtc_field_read(struct ti_k3_rtc *priv, enum ti_k3_rtc_fields f)
+{
+ int ret;
+ int val;
+
+ ret = regmap_field_read(priv->r_fields[f], &val);
+ /*
+ * We should'nt be seeing regmap fail on us for mmio reads
+ * This is possible if clk context fails, but that is'nt the case for us
+ */
+ if (WARN_ON_ONCE(ret))
+ return ret;
+ return val;
+}
+
+static void k3rtc_field_write(struct ti_k3_rtc *priv, enum ti_k3_rtc_fields f, u32 val)
+{
+ regmap_field_write(priv->r_fields[f], val);
+}
+
+/**
+ * k3rtc_fence - Ensure a register sync took place between the two domains
+ * @priv: pointer to priv data
+ *
+ * Return: 0 if the sync took place, else returns -ETIMEDOUT
+ */
+static int k3rtc_fence(struct ti_k3_rtc *priv)
+{
+ int ret;
+
+ ret = regmap_field_read_poll_timeout(priv->r_fields[K3RTC_PEND], ret,
+ !ret, 2, priv->sync_timeout_us);
+
+ return ret;
+}
+
+static inline int k3rtc_check_unlocked(struct ti_k3_rtc *priv)
+{
+ int ret;
+
+ ret = k3rtc_field_read(priv, K3RTC_UNLOCK);
+ if (ret < 0)
+ return ret;
+
+ return (ret) ? 0 : 1;
+}
+
+static int k3rtc_unlock_rtc(struct ti_k3_rtc *priv)
+{
+ int ret;
+
+ ret = k3rtc_check_unlocked(priv);
+ if (!ret)
+ return ret;
+
+ k3rtc_field_write(priv, K3RTC_KICK0, K3RTC_KICK0_UNLOCK_VALUE);
+ k3rtc_field_write(priv, K3RTC_KICK1, K3RTC_KICK1_UNLOCK_VALUE);
+
+ /* Skip fence since we are going to check the unlock bit as fence */
+ ret = regmap_field_read_poll_timeout(priv->r_fields[K3RTC_UNLOCK], ret,
+ !ret, 2, priv->sync_timeout_us);
+
+ return ret;
+}
+
+static int k3rtc_configure(struct device *dev)
+{
+ int ret;
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+
+ /*
+ * HWBUG: The compare statemachine is broken if the RTC module
+ * is NOT unlocked in under one second of boot - which is pretty long
+ * time from the perspective of Linux driver (module load, u-boot
+ * shell all can take much longer than this.
+ *
+ * In such occurrence, it is assumed that the RTC module is un-usable
+ */
+ if (priv->soc->unlock_irq_erratum) {
+ ret = k3rtc_check_unlocked(priv);
+ /* If there is an error OR if we are locked, return error */
+ if (ret) {
+ dev_err(dev,
+ HW_ERR "Erratum i2327 unlock QUIRK! Cannot operate!!\n");
+ return -EFAULT;
+ }
+ } else {
+ /* May need to explicitly unlock first time */
+ ret = k3rtc_unlock_rtc(priv);
+ if (ret) {
+ dev_err(dev, "Failed to unlock(%d)!\n", ret);
+ return ret;
+ }
+ }
+
+ /* Enable Shadow register sync on 32k clk boundary */
+ k3rtc_field_write(priv, K3RTC_O32K_OSC_DEP_EN, 0x1);
+
+ /*
+ * Wait at least clk sync time before proceeding further programming.
+ * This ensures that the 32k based sync is active.
+ */
+ usleep_range(priv->sync_timeout_us, priv->sync_timeout_us + 5);
+
+ /* We need to ensure fence here to make sure sync here */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev,
+ "Failed fence osc_dep enable(%d) - is 32k clk working?!\n", ret);
+ return ret;
+ }
+
+ /*
+ * FMODE setting: Reading lower seconds will freeze value on higher
+ * seconds. This also implies that we must *ALWAYS* read lower seconds
+ * prior to reading higher seconds
+ */
+ k3rtc_field_write(priv, K3RTC_CNT_FMODE, K3RTC_CNT_FMODE_S_CNT_VALUE);
+
+ /* Clear any spurious IRQ sources if any */
+ k3rtc_field_write(priv, K3RTC_IRQ_STATUS_ALT, 0x1);
+ k3rtc_field_write(priv, K3RTC_IRQ_STATUS, 0x1);
+ /* Disable all IRQs */
+ k3rtc_field_write(priv, K3RTC_IRQ_ENABLE_CLR_ALT, 0x1);
+ k3rtc_field_write(priv, K3RTC_IRQ_ENABLE_CLR, 0x1);
+
+ /* And.. Let us Sync the writes in */
+ return k3rtc_fence(priv);
+}
+
+static int ti_k3_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 seconds_lo, seconds_hi;
+
+ seconds_lo = k3rtc_field_read(priv, K3RTC_S_CNT_LSW);
+ seconds_hi = k3rtc_field_read(priv, K3RTC_S_CNT_MSW);
+
+ rtc_time64_to_tm((((time64_t)seconds_hi) << 32) | (time64_t)seconds_lo, tm);
+
+ return 0;
+}
+
+static int ti_k3_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ time64_t seconds;
+
+ seconds = rtc_tm_to_time64(tm);
+
+ /*
+ * Read operation on LSW will freeze the RTC, so to update
+ * the time, we cannot use field operations. just write since the
+ * reserved bits are ignored.
+ */
+ regmap_write(priv->regmap, REG_K3RTC_S_CNT_LSW, seconds);
+ regmap_write(priv->regmap, REG_K3RTC_S_CNT_MSW, seconds >> 32);
+
+ return k3rtc_fence(priv);
+}
+
+static int ti_k3_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 reg;
+ u32 offset = enabled ? K3RTC_IRQ_ENABLE_SET : K3RTC_IRQ_ENABLE_CLR;
+
+ reg = k3rtc_field_read(priv, K3RTC_IRQ_ENABLE_SET);
+ if ((enabled && reg) || (!enabled && !reg))
+ return 0;
+
+ k3rtc_field_write(priv, offset, 0x1);
+
+ /*
+ * Ensure the write sync is through - NOTE: it should be OK to have
+ * ISR to fire as we are checking sync (which should be done in a 32k
+ * cycle or so).
+ */
+ return k3rtc_fence(priv);
+}
+
+static int ti_k3_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alarm)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 seconds_lo, seconds_hi;
+
+ seconds_lo = k3rtc_field_read(priv, K3RTC_ALM_S_CNT_LSW);
+ seconds_hi = k3rtc_field_read(priv, K3RTC_ALM_S_CNT_MSW);
+
+ rtc_time64_to_tm((((time64_t)seconds_hi) << 32) | (time64_t)seconds_lo, &alarm->time);
+
+ alarm->enabled = k3rtc_field_read(priv, K3RTC_IRQ_ENABLE_SET);
+
+ return 0;
+}
+
+static int ti_k3_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alarm)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ time64_t seconds;
+ int ret;
+
+ seconds = rtc_tm_to_time64(&alarm->time);
+
+ k3rtc_field_write(priv, K3RTC_ALM_S_CNT_LSW, seconds);
+ k3rtc_field_write(priv, K3RTC_ALM_S_CNT_MSW, (seconds >> 32));
+
+ /* Make sure the alarm time is synced in */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence(%d)!\n", ret);
+ return ret;
+ }
+
+ /* Alarm irq enable will do a sync */
+ return ti_k3_rtc_alarm_irq_enable(dev, alarm->enabled);
+}
+
+static int ti_k3_rtc_read_offset(struct device *dev, long *offset)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 ticks_per_hr = priv->rate_32k * 3600;
+ int comp;
+ s64 tmp;
+
+ comp = k3rtc_field_read(priv, K3RTC_COMP);
+
+ /* Convert from RTC calibration register format to ppb format */
+ tmp = comp * (s64)K3RTC_PPB_MULT;
+ if (tmp < 0)
+ tmp -= ticks_per_hr / 2LL;
+ else
+ tmp += ticks_per_hr / 2LL;
+ tmp = div_s64(tmp, ticks_per_hr);
+
+ /* Offset value operates in negative way, so swap sign */
+ *offset = (long)-tmp;
+
+ return 0;
+}
+
+static int ti_k3_rtc_set_offset(struct device *dev, long offset)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 ticks_per_hr = priv->rate_32k * 3600;
+ int comp;
+ s64 tmp;
+
+ /* Make sure offset value is within supported range */
+ if (offset < K3RTC_MIN_OFFSET || offset > K3RTC_MAX_OFFSET)
+ return -ERANGE;
+
+ /* Convert from ppb format to RTC calibration register format */
+ tmp = offset * (s64)ticks_per_hr;
+ if (tmp < 0)
+ tmp -= K3RTC_PPB_MULT / 2LL;
+ else
+ tmp += K3RTC_PPB_MULT / 2LL;
+ tmp = div_s64(tmp, K3RTC_PPB_MULT);
+
+ /* Offset value operates in negative way, so swap sign */
+ comp = (int)-tmp;
+
+ k3rtc_field_write(priv, K3RTC_COMP, comp);
+
+ return k3rtc_fence(priv);
+}
+
+static irqreturn_t ti_k3_rtc_interrupt(s32 irq, void *dev_id)
+{
+ struct device *dev = dev_id;
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+ u32 reg;
+ int ret;
+
+ /*
+ * IRQ assertion can be very fast, however, the IRQ Status clear
+ * de-assert depends on 32k clock edge in the 32k domain
+ * If we clear the status prior to the first 32k clock edge,
+ * the status bit is cleared, but the IRQ stays re-asserted.
+ *
+ * To prevent this condition, we need to wait for clk sync time.
+ * We can either do that by polling the 32k observability signal for
+ * a toggle OR we could just sleep and let the processor do other
+ * stuff.
+ */
+ usleep_range(priv->sync_timeout_us, priv->sync_timeout_us + 2);
+
+ /* Lets make sure that this is a valid interrupt */
+ reg = k3rtc_field_read(priv, K3RTC_IRQ_STATUS);
+
+ if (!reg) {
+ u32 raw = k3rtc_field_read(priv, K3RTC_IRQ_STATUS_RAW);
+
+ dev_err(dev,
+ HW_ERR
+ "Erratum i2327/IRQ trig: status: 0x%08x / 0x%08x\n", reg, raw);
+ return IRQ_NONE;
+ }
+
+ /*
+ * Write 1 to clear status reg
+ * We cannot use a field operation here due to a potential race between
+ * 32k domain and vbus domain.
+ */
+ regmap_write(priv->regmap, REG_K3RTC_IRQSTATUS_SYS, 0x1);
+
+ /* Sync the write in */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence irq status clr(%d)!\n", ret);
+ return IRQ_NONE;
+ }
+
+ /*
+ * Force the 32k status to be reloaded back in to ensure status is
+ * reflected back correctly.
+ */
+ k3rtc_field_write(priv, K3RTC_RELOAD_FROM_BBD, 0x1);
+
+ /* Ensure the write sync is through */
+ ret = k3rtc_fence(priv);
+ if (ret) {
+ dev_err(dev, "Failed to fence reload from bbd(%d)!\n", ret);
+ return IRQ_NONE;
+ }
+
+ /* Now we ensure that the status bit is cleared */
+ ret = regmap_field_read_poll_timeout(priv->r_fields[K3RTC_IRQ_STATUS],
+ ret, !ret, 2, priv->sync_timeout_us);
+ if (ret) {
+ dev_err(dev, "Time out waiting for status clear\n");
+ return IRQ_NONE;
+ }
+
+ /* Notify RTC core on event */
+ rtc_update_irq(priv->rtc_dev, 1, RTC_IRQF | RTC_AF);
+
+ return IRQ_HANDLED;
+}
+
+static const struct rtc_class_ops ti_k3_rtc_ops = {
+ .read_time = ti_k3_rtc_read_time,
+ .set_time = ti_k3_rtc_set_time,
+ .read_alarm = ti_k3_rtc_read_alarm,
+ .set_alarm = ti_k3_rtc_set_alarm,
+ .read_offset = ti_k3_rtc_read_offset,
+ .set_offset = ti_k3_rtc_set_offset,
+ .alarm_irq_enable = ti_k3_rtc_alarm_irq_enable,
+};
+
+static int ti_k3_rtc_scratch_read(void *priv_data, unsigned int offset,
+ void *val, size_t bytes)
+{
+ struct ti_k3_rtc *priv = (struct ti_k3_rtc *)priv_data;
+ int ret;
+
+ ret = regmap_bulk_read(priv->regmap, REG_K3RTC_SCRATCH0 + offset, val, bytes / 4);
+
+ return ret;
+}
+
+static int ti_k3_rtc_scratch_write(void *priv_data, unsigned int offset,
+ void *val, size_t bytes)
+{
+ struct ti_k3_rtc *priv = (struct ti_k3_rtc *)priv_data;
+ int ret;
+
+ ret = regmap_bulk_write(priv->regmap, REG_K3RTC_SCRATCH0 + offset, val, bytes / 4);
+ if (ret)
+ return ret;
+
+ return k3rtc_fence(priv);
+}
+
+static struct nvmem_config ti_k3_rtc_nvmem_config = {
+ .name = "ti_k3_rtc_scratch",
+ .word_size = 4,
+ .stride = 4,
+ .size = REG_K3RTC_SCRATCH7 - REG_K3RTC_SCRATCH0 + 4,
+ .reg_read = ti_k3_rtc_scratch_read,
+ .reg_write = ti_k3_rtc_scratch_write,
+};
+
+static int k3rtc_get_32kclk(struct device *dev, struct ti_k3_rtc *priv)
+{
+ int ret;
+ struct clk *clk;
+
+ clk = devm_clk_get(dev, "osc32k");
+ if (IS_ERR(clk)) {
+ dev_err(dev, "No input reference 32k clock\n");
+ return PTR_ERR(clk);
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable the reference 32k clock(%d)\n", ret);
+ return ret;
+ }
+
+ ret = devm_add_action_or_reset(dev, (void (*)(void *))clk_disable_unprepare, clk);
+ if (ret)
+ return ret;
+
+ priv->rate_32k = clk_get_rate(clk);
+
+ /* Make sure we are exact 32k clock. Else, try to compensate delay */
+ if (priv->rate_32k != 32768)
+ dev_warn(dev, "Clock rate %ld is not 32768! Could misbehave!\n",
+ priv->rate_32k);
+
+ /*
+ * Sync timeout should be two 32k clk sync cycles = ~61uS. We double
+ * it to comprehend intermediate bus segment and cpu frequency
+ * deltas
+ */
+ priv->sync_timeout_us = (u32)(DIV_ROUND_UP_ULL(1000000, priv->rate_32k) * 4);
+
+ return ret;
+}
+
+static int k3rtc_get_vbusclk(struct device *dev, struct ti_k3_rtc *priv)
+{
+ int ret;
+ struct clk *clk;
+
+ /* Note: VBUS is'nt a context clock, it is needed for hardware operation */
+ clk = devm_clk_get(dev, "vbus");
+ if (IS_ERR(clk)) {
+ dev_err(dev, "No input vbus clock\n");
+ return PTR_ERR(clk);
+ }
+
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable the vbus clock(%d)\n", ret);
+ return ret;
+ }
+
+ ret = devm_add_action_or_reset(dev, (void (*)(void *))clk_disable_unprepare, clk);
+ return ret;
+}
+
+static int ti_k3_rtc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ti_k3_rtc *priv;
+ void __iomem *rtc_base;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(struct ti_k3_rtc), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ rtc_base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(rtc_base))
+ return PTR_ERR(rtc_base);
+
+ priv->regmap = devm_regmap_init_mmio(dev, rtc_base, &ti_k3_rtc_regmap_config);
+ if (IS_ERR(priv->regmap))
+ return PTR_ERR(priv->regmap);
+
+ ret = devm_regmap_field_bulk_alloc(dev, priv->regmap, priv->r_fields,
+ ti_rtc_reg_fields, K3_RTC_MAX_FIELDS);
+ if (ret)
+ return ret;
+
+ ret = k3rtc_get_32kclk(dev, priv);
+ if (ret)
+ return ret;
+ ret = k3rtc_get_vbusclk(dev, priv);
+ if (ret)
+ return ret;
+
+ ret = platform_get_irq(pdev, 0);
+ if (ret < 0)
+ return ret;
+ priv->irq = (unsigned int)ret;
+
+ priv->rtc_dev = devm_rtc_allocate_device(dev);
+ if (IS_ERR(priv->rtc_dev))
+ return PTR_ERR(priv->rtc_dev);
+
+ priv->soc = of_device_get_match_data(dev);
+
+ priv->rtc_dev->ops = &ti_k3_rtc_ops;
+ priv->rtc_dev->range_max = (1ULL << 48) - 1; /* 48Bit seconds */
+ ti_k3_rtc_nvmem_config.priv = priv;
+
+ ret = devm_request_threaded_irq(dev, priv->irq, NULL,
+ ti_k3_rtc_interrupt,
+ IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+ dev_name(dev), dev);
+ if (ret) {
+ dev_err(dev, "Could not request IRQ: %d\n", ret);
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, priv);
+
+ ret = k3rtc_configure(dev);
+ if (ret)
+ return ret;
+
+ if (device_property_present(dev, "wakeup-source"))
+ device_init_wakeup(dev, true);
+ else
+ device_set_wakeup_capable(dev, true);
+
+ ret = devm_rtc_register_device(priv->rtc_dev);
+ if (ret)
+ return ret;
+
+ ret = devm_rtc_nvmem_register(priv->rtc_dev, &ti_k3_rtc_nvmem_config);
+ return ret;
+}
+
+static const struct ti_k3_rtc_soc_data ti_k3_am62_data = {
+ .unlock_irq_erratum = true,
+};
+
+static const struct of_device_id ti_k3_rtc_of_match_table[] = {
+ {.compatible = "ti,am62-rtc", .data = &ti_k3_am62_data},
+ {}
+};
+MODULE_DEVICE_TABLE(of, ti_k3_rtc_of_match_table);
+
+static int __maybe_unused ti_k3_rtc_suspend(struct device *dev)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+
+ if (device_may_wakeup(dev))
+ enable_irq_wake(priv->irq);
+ return 0;
+}
+
+static int __maybe_unused ti_k3_rtc_resume(struct device *dev)
+{
+ struct ti_k3_rtc *priv = dev_get_drvdata(dev);
+
+ if (device_may_wakeup(dev))
+ disable_irq_wake(priv->irq);
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(ti_k3_rtc_pm_ops, ti_k3_rtc_suspend, ti_k3_rtc_resume);
+
+static struct platform_driver ti_k3_rtc_driver = {
+ .probe = ti_k3_rtc_probe,
+ .driver = {
+ .name = "rtc-ti-k3",
+ .of_match_table = ti_k3_rtc_of_match_table,
+ .pm = &ti_k3_rtc_pm_ops,
+ },
+};
+module_platform_driver(ti_k3_rtc_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("TI K3 RTC driver");
+MODULE_AUTHOR("Nishanth Menon");