| Message ID | 1652808360-9830-2-git-send-email-quic_khsieh@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | eDP/DP Phy vdda realted function | expand |
Hi, On Tue, May 17, 2022 at 10:26 AM Kuogee Hsieh <quic_khsieh@quicinc.com> wrote: > > This patch add regulator_set_load() to both eDP and DP phy driver > to have totally control regulators. > > Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> > --- > drivers/phy/qualcomm/phy-qcom-edp.c | 25 +++++++++++++++++++++---- > drivers/phy/qualcomm/phy-qcom-qmp.c | 24 ++++++++++++++++++++++++ > 2 files changed, 45 insertions(+), 4 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c > index cacd32f..9b55095 100644 > --- a/drivers/phy/qualcomm/phy-qcom-edp.c > +++ b/drivers/phy/qualcomm/phy-qcom-edp.c > @@ -87,17 +87,24 @@ struct qcom_edp { > > struct clk_bulk_data clks[2]; > struct regulator_bulk_data supplies[2]; > + int enable_load[2]; > + int disable_load[2]; > }; > > static int qcom_edp_phy_init(struct phy *phy) > { > struct qcom_edp *edp = phy_get_drvdata(phy); > int ret; > + int num_consumers = ARRAY_SIZE(edp->supplies); > + int i; > > - ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies); > + ret = regulator_bulk_enable(num_consumers, edp->supplies); > if (ret) > return ret; > > + for (i = num_consumers - 1; i >= 0; --i) > + regulator_set_load(edp->supplies[i].consumer, edp->enable_load[i]); > + > ret = clk_bulk_prepare_enable(ARRAY_SIZE(edp->clks), edp->clks); > if (ret) > goto out_disable_supplies; > @@ -425,9 +432,15 @@ static int qcom_edp_phy_power_off(struct phy *phy) > static int qcom_edp_phy_exit(struct phy *phy) > { > struct qcom_edp *edp = phy_get_drvdata(phy); > + int num_consumers = ARRAY_SIZE(edp->supplies); > + int i; > > clk_bulk_disable_unprepare(ARRAY_SIZE(edp->clks), edp->clks); > - regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies); > + > + for (i = num_consumers - 1; i >= 0; --i) > + regulator_set_load(edp->supplies[i].consumer, edp->disable_load[i]); > + > + regulator_bulk_disable(num_consumers, edp->supplies); > > return 0; > } > @@ -633,8 +646,12 @@ static int qcom_edp_phy_probe(struct platform_device *pdev) > if (ret) > return ret; > > - edp->supplies[0].supply = "vdda-phy"; > - edp->supplies[1].supply = "vdda-pll"; > + edp->supplies[0].supply = "vdda-1p2"; > + edp->supplies[1].supply = "vdda-0p9"; > + edp->enable_load[0] = 21800; /* 1.2 V */ > + edp->enable_load[1] = 36000; /* 1.2 V */ > + edp->disable_load[0] = 4; /* 0.9 V */ > + edp->disable_load[1] = 4; /* 10.9V */ 10.9V? That's a lot! > ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies); > if (ret) > return ret; > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c > index b144ae1..c589231 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c > @@ -3130,6 +3130,8 @@ struct qmp_phy_cfg { > int num_resets; > /* regulators to be requested */ > const char * const *vreg_list; > + const unsigned int *vreg_enable_load; > + const unsigned int *vreg_disable_load; > int num_vregs; > > /* array of registers with different offsets */ > @@ -3346,6 +3348,14 @@ static const char * const qmp_phy_vreg_l[] = { > "vdda-phy", "vdda-pll", > }; > > +static const unsigned int qmp_phy_vreg_enable_load[] = { > + 21800, 36000 > +}; > + > +static const unsigned int qmp_phy_vreg_disable_load[] = { > + 4, 32 > +}; > + > static const struct qmp_phy_cfg ipq8074_usb3phy_cfg = { > .type = PHY_TYPE_USB3, > .nlanes = 1, > @@ -4072,6 +4082,8 @@ static const struct qmp_phy_cfg sm8250_usb3phy_cfg = { > .reset_list = msm8996_usb3phy_reset_l, > .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), > .vreg_list = qmp_phy_vreg_l, > + .vreg_enable_load = qmp_phy_vreg_enable_load, > + .vreg_disable_load = qmp_phy_vreg_disable_load, > .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > .regs = qmp_v4_usb3phy_regs_layout, > > @@ -4139,6 +4151,8 @@ static const struct qmp_phy_cfg sm8250_dpphy_cfg = { > .reset_list = msm8996_usb3phy_reset_l, > .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), > .vreg_list = qmp_phy_vreg_l, > + .vreg_enable_load = qmp_phy_vreg_enable_load, > + .vreg_disable_load = qmp_phy_vreg_disable_load, > .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > .regs = qmp_v4_usb3phy_regs_layout, > > @@ -5015,6 +5029,11 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy) > goto err_reg_enable; > } > > + if (cfg->vreg_enable_load) { > + for (i = cfg->num_vregs - 1; i >= 0; --i) > + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_enable_load[i]); > + } > + > for (i = 0; i < cfg->num_resets; i++) { > ret = reset_control_assert(qmp->resets[i]); > if (ret) { > @@ -5116,6 +5135,11 @@ static int qcom_qmp_phy_com_exit(struct qmp_phy *qphy) > > clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); > > + if (cfg->vreg_disable_load[i]) { > + for (i = cfg->num_vregs - 1; i >= 0; --i) > + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_disable_load[i]); > + } > + > regulator_bulk_disable(cfg->num_vregs, qmp->vregs); You don't haven't needed the regulator_set_load() on regulator_bulk_disable() for many years now. See commit 5451781dadf8 ("regulator: core: Only count load for enabled consumers") ...so the only place you should set the load is in qcom_edp_phy_init() -Doug
On 17-05-22, 10:25, Kuogee Hsieh wrote: pls use the correct subsystem tag, "phy: xxx" in this case > This patch add regulator_set_load() to both eDP and DP phy driver > to have totally control regulators. Can you explain what is meant by "totally control regulators" > > Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> > --- > drivers/phy/qualcomm/phy-qcom-edp.c | 25 +++++++++++++++++++++---- > drivers/phy/qualcomm/phy-qcom-qmp.c | 24 ++++++++++++++++++++++++ > 2 files changed, 45 insertions(+), 4 deletions(-) > > diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c > index cacd32f..9b55095 100644 > --- a/drivers/phy/qualcomm/phy-qcom-edp.c > +++ b/drivers/phy/qualcomm/phy-qcom-edp.c > @@ -87,17 +87,24 @@ struct qcom_edp { > > struct clk_bulk_data clks[2]; > struct regulator_bulk_data supplies[2]; > + int enable_load[2]; > + int disable_load[2]; > }; > > static int qcom_edp_phy_init(struct phy *phy) > { > struct qcom_edp *edp = phy_get_drvdata(phy); > int ret; > + int num_consumers = ARRAY_SIZE(edp->supplies); > + int i; > > - ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies); > + ret = regulator_bulk_enable(num_consumers, edp->supplies); > if (ret) > return ret; > > + for (i = num_consumers - 1; i >= 0; --i) > + regulator_set_load(edp->supplies[i].consumer, edp->enable_load[i]); > + > ret = clk_bulk_prepare_enable(ARRAY_SIZE(edp->clks), edp->clks); > if (ret) > goto out_disable_supplies; > @@ -425,9 +432,15 @@ static int qcom_edp_phy_power_off(struct phy *phy) > static int qcom_edp_phy_exit(struct phy *phy) > { > struct qcom_edp *edp = phy_get_drvdata(phy); > + int num_consumers = ARRAY_SIZE(edp->supplies); > + int i; > > clk_bulk_disable_unprepare(ARRAY_SIZE(edp->clks), edp->clks); > - regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies); > + > + for (i = num_consumers - 1; i >= 0; --i) > + regulator_set_load(edp->supplies[i].consumer, edp->disable_load[i]); > + > + regulator_bulk_disable(num_consumers, edp->supplies); > > return 0; > } > @@ -633,8 +646,12 @@ static int qcom_edp_phy_probe(struct platform_device *pdev) > if (ret) > return ret; > > - edp->supplies[0].supply = "vdda-phy"; > - edp->supplies[1].supply = "vdda-pll"; > + edp->supplies[0].supply = "vdda-1p2"; > + edp->supplies[1].supply = "vdda-0p9"; These are documented in bindings, so cannot be removed, Reminder binding is an ABI You have not documented the new names either... > + edp->enable_load[0] = 21800; /* 1.2 V */ > + edp->enable_load[1] = 36000; /* 1.2 V */ > + edp->disable_load[0] = 4; /* 0.9 V */ > + edp->disable_load[1] = 4; /* 10.9V */ is that correct, 10.9V? > ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies); > if (ret) > return ret; > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c > index b144ae1..c589231 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c This is a different driver, so should be a different patch! > @@ -3130,6 +3130,8 @@ struct qmp_phy_cfg { > int num_resets; > /* regulators to be requested */ > const char * const *vreg_list; > + const unsigned int *vreg_enable_load; > + const unsigned int *vreg_disable_load; > int num_vregs; > > /* array of registers with different offsets */ > @@ -3346,6 +3348,14 @@ static const char * const qmp_phy_vreg_l[] = { > "vdda-phy", "vdda-pll", > }; > > +static const unsigned int qmp_phy_vreg_enable_load[] = { > + 21800, 36000 > +}; > + > +static const unsigned int qmp_phy_vreg_disable_load[] = { > + 4, 32 > +}; > + > static const struct qmp_phy_cfg ipq8074_usb3phy_cfg = { > .type = PHY_TYPE_USB3, > .nlanes = 1, > @@ -4072,6 +4082,8 @@ static const struct qmp_phy_cfg sm8250_usb3phy_cfg = { > .reset_list = msm8996_usb3phy_reset_l, > .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), > .vreg_list = qmp_phy_vreg_l, > + .vreg_enable_load = qmp_phy_vreg_enable_load, > + .vreg_disable_load = qmp_phy_vreg_disable_load, > .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > .regs = qmp_v4_usb3phy_regs_layout, > > @@ -4139,6 +4151,8 @@ static const struct qmp_phy_cfg sm8250_dpphy_cfg = { > .reset_list = msm8996_usb3phy_reset_l, > .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), > .vreg_list = qmp_phy_vreg_l, > + .vreg_enable_load = qmp_phy_vreg_enable_load, > + .vreg_disable_load = qmp_phy_vreg_disable_load, > .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > .regs = qmp_v4_usb3phy_regs_layout, > > @@ -5015,6 +5029,11 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy) > goto err_reg_enable; > } > > + if (cfg->vreg_enable_load) { > + for (i = cfg->num_vregs - 1; i >= 0; --i) > + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_enable_load[i]); > + } > + > for (i = 0; i < cfg->num_resets; i++) { > ret = reset_control_assert(qmp->resets[i]); > if (ret) { > @@ -5116,6 +5135,11 @@ static int qcom_qmp_phy_com_exit(struct qmp_phy *qphy) > > clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); > > + if (cfg->vreg_disable_load[i]) { > + for (i = cfg->num_vregs - 1; i >= 0; --i) > + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_disable_load[i]); > + } > + > regulator_bulk_disable(cfg->num_vregs, qmp->vregs); > > mutex_unlock(&qmp->phy_mutex); > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project
On 5/18/2022 2:29 AM, Vinod Koul wrote: > On 17-05-22, 10:25, Kuogee Hsieh wrote: > > pls use the correct subsystem tag, "phy: xxx" in this case > >> This patch add regulator_set_load() to both eDP and DP phy driver >> to have totally control regulators. > Can you explain what is meant by "totally control regulators" Original regulator_set_load() is done by DP controller. This patch has moved regulator_set_load() from DP controller to DP phy. Therefore DP phy has total control of both vdda-phy and vda-pll regulators. > >> Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> >> --- >> drivers/phy/qualcomm/phy-qcom-edp.c | 25 +++++++++++++++++++++---- >> drivers/phy/qualcomm/phy-qcom-qmp.c | 24 ++++++++++++++++++++++++ >> 2 files changed, 45 insertions(+), 4 deletions(-) >> >> diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c >> index cacd32f..9b55095 100644 >> --- a/drivers/phy/qualcomm/phy-qcom-edp.c >> +++ b/drivers/phy/qualcomm/phy-qcom-edp.c >> @@ -87,17 +87,24 @@ struct qcom_edp { >> >> struct clk_bulk_data clks[2]; >> struct regulator_bulk_data supplies[2]; >> + int enable_load[2]; >> + int disable_load[2]; >> }; >> >> static int qcom_edp_phy_init(struct phy *phy) >> { >> struct qcom_edp *edp = phy_get_drvdata(phy); >> int ret; >> + int num_consumers = ARRAY_SIZE(edp->supplies); >> + int i; >> >> - ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies); >> + ret = regulator_bulk_enable(num_consumers, edp->supplies); >> if (ret) >> return ret; >> >> + for (i = num_consumers - 1; i >= 0; --i) >> + regulator_set_load(edp->supplies[i].consumer, edp->enable_load[i]); >> + >> ret = clk_bulk_prepare_enable(ARRAY_SIZE(edp->clks), edp->clks); >> if (ret) >> goto out_disable_supplies; >> @@ -425,9 +432,15 @@ static int qcom_edp_phy_power_off(struct phy *phy) >> static int qcom_edp_phy_exit(struct phy *phy) >> { >> struct qcom_edp *edp = phy_get_drvdata(phy); >> + int num_consumers = ARRAY_SIZE(edp->supplies); >> + int i; >> >> clk_bulk_disable_unprepare(ARRAY_SIZE(edp->clks), edp->clks); >> - regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies); >> + >> + for (i = num_consumers - 1; i >= 0; --i) >> + regulator_set_load(edp->supplies[i].consumer, edp->disable_load[i]); >> + >> + regulator_bulk_disable(num_consumers, edp->supplies); >> >> return 0; >> } >> @@ -633,8 +646,12 @@ static int qcom_edp_phy_probe(struct platform_device *pdev) >> if (ret) >> return ret; >> >> - edp->supplies[0].supply = "vdda-phy"; >> - edp->supplies[1].supply = "vdda-pll"; >> + edp->supplies[0].supply = "vdda-1p2"; >> + edp->supplies[1].supply = "vdda-0p9"; > These are documented in bindings, so cannot be removed, Reminder binding > is an ABI > > You have not documented the new names either... > >> + edp->enable_load[0] = 21800; /* 1.2 V */ >> + edp->enable_load[1] = 36000; /* 1.2 V */ >> + edp->disable_load[0] = 4; /* 0.9 V */ >> + edp->disable_load[1] = 4; /* 10.9V */ > is that correct, 10.9V? > >> ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies); >> if (ret) >> return ret; >> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c >> index b144ae1..c589231 100644 >> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c >> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c > This is a different driver, so should be a different patch! > >> @@ -3130,6 +3130,8 @@ struct qmp_phy_cfg { >> int num_resets; >> /* regulators to be requested */ >> const char * const *vreg_list; >> + const unsigned int *vreg_enable_load; >> + const unsigned int *vreg_disable_load; >> int num_vregs; >> >> /* array of registers with different offsets */ >> @@ -3346,6 +3348,14 @@ static const char * const qmp_phy_vreg_l[] = { >> "vdda-phy", "vdda-pll", >> }; >> >> +static const unsigned int qmp_phy_vreg_enable_load[] = { >> + 21800, 36000 >> +}; >> + >> +static const unsigned int qmp_phy_vreg_disable_load[] = { >> + 4, 32 >> +}; >> + >> static const struct qmp_phy_cfg ipq8074_usb3phy_cfg = { >> .type = PHY_TYPE_USB3, >> .nlanes = 1, >> @@ -4072,6 +4082,8 @@ static const struct qmp_phy_cfg sm8250_usb3phy_cfg = { >> .reset_list = msm8996_usb3phy_reset_l, >> .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), >> .vreg_list = qmp_phy_vreg_l, >> + .vreg_enable_load = qmp_phy_vreg_enable_load, >> + .vreg_disable_load = qmp_phy_vreg_disable_load, >> .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), >> .regs = qmp_v4_usb3phy_regs_layout, >> >> @@ -4139,6 +4151,8 @@ static const struct qmp_phy_cfg sm8250_dpphy_cfg = { >> .reset_list = msm8996_usb3phy_reset_l, >> .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), >> .vreg_list = qmp_phy_vreg_l, >> + .vreg_enable_load = qmp_phy_vreg_enable_load, >> + .vreg_disable_load = qmp_phy_vreg_disable_load, >> .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), >> .regs = qmp_v4_usb3phy_regs_layout, >> >> @@ -5015,6 +5029,11 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy) >> goto err_reg_enable; >> } >> >> + if (cfg->vreg_enable_load) { >> + for (i = cfg->num_vregs - 1; i >= 0; --i) >> + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_enable_load[i]); >> + } >> + >> for (i = 0; i < cfg->num_resets; i++) { >> ret = reset_control_assert(qmp->resets[i]); >> if (ret) { >> @@ -5116,6 +5135,11 @@ static int qcom_qmp_phy_com_exit(struct qmp_phy *qphy) >> >> clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); >> >> + if (cfg->vreg_disable_load[i]) { >> + for (i = cfg->num_vregs - 1; i >= 0; --i) >> + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_disable_load[i]); >> + } >> + >> regulator_bulk_disable(cfg->num_vregs, qmp->vregs); >> >> mutex_unlock(&qmp->phy_mutex); >> -- >> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, >> a Linux Foundation Collaborative Project
diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c index cacd32f..9b55095 100644 --- a/drivers/phy/qualcomm/phy-qcom-edp.c +++ b/drivers/phy/qualcomm/phy-qcom-edp.c @@ -87,17 +87,24 @@ struct qcom_edp { struct clk_bulk_data clks[2]; struct regulator_bulk_data supplies[2]; + int enable_load[2]; + int disable_load[2]; }; static int qcom_edp_phy_init(struct phy *phy) { struct qcom_edp *edp = phy_get_drvdata(phy); int ret; + int num_consumers = ARRAY_SIZE(edp->supplies); + int i; - ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies); + ret = regulator_bulk_enable(num_consumers, edp->supplies); if (ret) return ret; + for (i = num_consumers - 1; i >= 0; --i) + regulator_set_load(edp->supplies[i].consumer, edp->enable_load[i]); + ret = clk_bulk_prepare_enable(ARRAY_SIZE(edp->clks), edp->clks); if (ret) goto out_disable_supplies; @@ -425,9 +432,15 @@ static int qcom_edp_phy_power_off(struct phy *phy) static int qcom_edp_phy_exit(struct phy *phy) { struct qcom_edp *edp = phy_get_drvdata(phy); + int num_consumers = ARRAY_SIZE(edp->supplies); + int i; clk_bulk_disable_unprepare(ARRAY_SIZE(edp->clks), edp->clks); - regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies); + + for (i = num_consumers - 1; i >= 0; --i) + regulator_set_load(edp->supplies[i].consumer, edp->disable_load[i]); + + regulator_bulk_disable(num_consumers, edp->supplies); return 0; } @@ -633,8 +646,12 @@ static int qcom_edp_phy_probe(struct platform_device *pdev) if (ret) return ret; - edp->supplies[0].supply = "vdda-phy"; - edp->supplies[1].supply = "vdda-pll"; + edp->supplies[0].supply = "vdda-1p2"; + edp->supplies[1].supply = "vdda-0p9"; + edp->enable_load[0] = 21800; /* 1.2 V */ + edp->enable_load[1] = 36000; /* 1.2 V */ + edp->disable_load[0] = 4; /* 0.9 V */ + edp->disable_load[1] = 4; /* 10.9V */ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies); if (ret) return ret; diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c index b144ae1..c589231 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c @@ -3130,6 +3130,8 @@ struct qmp_phy_cfg { int num_resets; /* regulators to be requested */ const char * const *vreg_list; + const unsigned int *vreg_enable_load; + const unsigned int *vreg_disable_load; int num_vregs; /* array of registers with different offsets */ @@ -3346,6 +3348,14 @@ static const char * const qmp_phy_vreg_l[] = { "vdda-phy", "vdda-pll", }; +static const unsigned int qmp_phy_vreg_enable_load[] = { + 21800, 36000 +}; + +static const unsigned int qmp_phy_vreg_disable_load[] = { + 4, 32 +}; + static const struct qmp_phy_cfg ipq8074_usb3phy_cfg = { .type = PHY_TYPE_USB3, .nlanes = 1, @@ -4072,6 +4082,8 @@ static const struct qmp_phy_cfg sm8250_usb3phy_cfg = { .reset_list = msm8996_usb3phy_reset_l, .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), .vreg_list = qmp_phy_vreg_l, + .vreg_enable_load = qmp_phy_vreg_enable_load, + .vreg_disable_load = qmp_phy_vreg_disable_load, .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), .regs = qmp_v4_usb3phy_regs_layout, @@ -4139,6 +4151,8 @@ static const struct qmp_phy_cfg sm8250_dpphy_cfg = { .reset_list = msm8996_usb3phy_reset_l, .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), .vreg_list = qmp_phy_vreg_l, + .vreg_enable_load = qmp_phy_vreg_enable_load, + .vreg_disable_load = qmp_phy_vreg_disable_load, .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), .regs = qmp_v4_usb3phy_regs_layout, @@ -5015,6 +5029,11 @@ static int qcom_qmp_phy_com_init(struct qmp_phy *qphy) goto err_reg_enable; } + if (cfg->vreg_enable_load) { + for (i = cfg->num_vregs - 1; i >= 0; --i) + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_enable_load[i]); + } + for (i = 0; i < cfg->num_resets; i++) { ret = reset_control_assert(qmp->resets[i]); if (ret) { @@ -5116,6 +5135,11 @@ static int qcom_qmp_phy_com_exit(struct qmp_phy *qphy) clk_bulk_disable_unprepare(cfg->num_clks, qmp->clks); + if (cfg->vreg_disable_load[i]) { + for (i = cfg->num_vregs - 1; i >= 0; --i) + regulator_set_load(qmp->vregs[i].consumer, cfg->vreg_disable_load[i]); + } + regulator_bulk_disable(cfg->num_vregs, qmp->vregs); mutex_unlock(&qmp->phy_mutex);
This patch add regulator_set_load() to both eDP and DP phy driver to have totally control regulators. Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com> --- drivers/phy/qualcomm/phy-qcom-edp.c | 25 +++++++++++++++++++++---- drivers/phy/qualcomm/phy-qcom-qmp.c | 24 ++++++++++++++++++++++++ 2 files changed, 45 insertions(+), 4 deletions(-)