| Message ID | 20220606164138.66535-12-andriy.shevchenko@linux.intel.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | platform/x86: introduce p2sb_bar() helper | expand |
Hi, On 6/6/22 18:41, Andy Shevchenko wrote: > From: Henning Schild <henning.schild@siemens.com> > > The two drivers that used to use this have been switched over to the > common P2SB accessor, so this code is not needed any longer. > > Signed-off-by: Henning Schild <henning.schild@siemens.com> > Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Thanks, patch looks good to me: Reviewed-by: Hans de Goede <hdegoede@redhat.com> Also Ack for merging this through the MFD tree. Regards, Hans > --- > drivers/platform/x86/simatic-ipc.c | 38 ------------------- > .../platform_data/x86/simatic-ipc-base.h | 2 - > 2 files changed, 40 deletions(-) > > diff --git a/drivers/platform/x86/simatic-ipc.c b/drivers/platform/x86/simatic-ipc.c > index b599cda5ba3c..26c35e1660cb 100644 > --- a/drivers/platform/x86/simatic-ipc.c > +++ b/drivers/platform/x86/simatic-ipc.c > @@ -101,44 +101,6 @@ static int register_platform_devices(u32 station_id) > return 0; > } > > -/* FIXME: this should eventually be done with generic P2SB discovery code > - * the individual drivers for watchdogs and LEDs access memory that implements > - * GPIO, but pinctrl will not come up because of missing ACPI entries > - * > - * While there is no conflict a cleaner solution would be to somehow bring up > - * pinctrl even with these ACPI entries missing, and base the drivers on pinctrl. > - * After which the following function could be dropped, together with the code > - * poking the memory. > - */ > -/* > - * Get membase address from PCI, used in leds and wdt module. Here we read > - * the bar0. The final address calculation is done in the appropriate modules > - */ > -u32 simatic_ipc_get_membase0(unsigned int p2sb) > -{ > - struct pci_bus *bus; > - u32 bar0 = 0; > - /* > - * The GPIO memory is in bar0 of the hidden P2SB device. > - * Unhide the device to have a quick look at it, before we hide it > - * again. > - * Also grab the pci rescan lock so that device does not get discovered > - * and remapped while it is visible. > - * This code is inspired by drivers/mfd/lpc_ich.c > - */ > - bus = pci_find_bus(0, 0); > - pci_lock_rescan_remove(); > - pci_bus_write_config_byte(bus, p2sb, 0xE1, 0x0); > - pci_bus_read_config_dword(bus, p2sb, PCI_BASE_ADDRESS_0, &bar0); > - > - bar0 &= ~0xf; > - pci_bus_write_config_byte(bus, p2sb, 0xE1, 0x1); > - pci_unlock_rescan_remove(); > - > - return bar0; > -} > -EXPORT_SYMBOL(simatic_ipc_get_membase0); > - > static int __init simatic_ipc_init_module(void) > { > const struct dmi_system_id *match; > diff --git a/include/linux/platform_data/x86/simatic-ipc-base.h b/include/linux/platform_data/x86/simatic-ipc-base.h > index 62d2bc774067..39fefd48cf4d 100644 > --- a/include/linux/platform_data/x86/simatic-ipc-base.h > +++ b/include/linux/platform_data/x86/simatic-ipc-base.h > @@ -24,6 +24,4 @@ struct simatic_ipc_platform { > u8 devmode; > }; > > -u32 simatic_ipc_get_membase0(unsigned int p2sb); > - > #endif /* __PLATFORM_DATA_X86_SIMATIC_IPC_BASE_H */
diff --git a/drivers/platform/x86/simatic-ipc.c b/drivers/platform/x86/simatic-ipc.c index b599cda5ba3c..26c35e1660cb 100644 --- a/drivers/platform/x86/simatic-ipc.c +++ b/drivers/platform/x86/simatic-ipc.c @@ -101,44 +101,6 @@ static int register_platform_devices(u32 station_id) return 0; } -/* FIXME: this should eventually be done with generic P2SB discovery code - * the individual drivers for watchdogs and LEDs access memory that implements - * GPIO, but pinctrl will not come up because of missing ACPI entries - * - * While there is no conflict a cleaner solution would be to somehow bring up - * pinctrl even with these ACPI entries missing, and base the drivers on pinctrl. - * After which the following function could be dropped, together with the code - * poking the memory. - */ -/* - * Get membase address from PCI, used in leds and wdt module. Here we read - * the bar0. The final address calculation is done in the appropriate modules - */ -u32 simatic_ipc_get_membase0(unsigned int p2sb) -{ - struct pci_bus *bus; - u32 bar0 = 0; - /* - * The GPIO memory is in bar0 of the hidden P2SB device. - * Unhide the device to have a quick look at it, before we hide it - * again. - * Also grab the pci rescan lock so that device does not get discovered - * and remapped while it is visible. - * This code is inspired by drivers/mfd/lpc_ich.c - */ - bus = pci_find_bus(0, 0); - pci_lock_rescan_remove(); - pci_bus_write_config_byte(bus, p2sb, 0xE1, 0x0); - pci_bus_read_config_dword(bus, p2sb, PCI_BASE_ADDRESS_0, &bar0); - - bar0 &= ~0xf; - pci_bus_write_config_byte(bus, p2sb, 0xE1, 0x1); - pci_unlock_rescan_remove(); - - return bar0; -} -EXPORT_SYMBOL(simatic_ipc_get_membase0); - static int __init simatic_ipc_init_module(void) { const struct dmi_system_id *match; diff --git a/include/linux/platform_data/x86/simatic-ipc-base.h b/include/linux/platform_data/x86/simatic-ipc-base.h index 62d2bc774067..39fefd48cf4d 100644 --- a/include/linux/platform_data/x86/simatic-ipc-base.h +++ b/include/linux/platform_data/x86/simatic-ipc-base.h @@ -24,6 +24,4 @@ struct simatic_ipc_platform { u8 devmode; }; -u32 simatic_ipc_get_membase0(unsigned int p2sb); - #endif /* __PLATFORM_DATA_X86_SIMATIC_IPC_BASE_H */