deleted file mode 100644
@@ -1,11 +0,0 @@
-* Clock bindings for Energy Micro efm32 Giant Gecko's Clock Management Unit
-
-Required properties:
-- compatible: Should be "efm32gg,cmu"
-- reg: Base address and length of the register set
-- interrupts: Interrupt used by the CMU
-- #clock-cells: Should be <1>
-
-The clock consumer should specify the desired clock by having the clock ID in
-its "clocks" phandle cell. The header efm32-clk.h contains a list of available
-IDs.
deleted file mode 100644
@@ -1,33 +0,0 @@
-* Energymicro efm32 i2c controller
-
-Required properties :
-
- - reg : Offset and length of the register set for the device
- - compatible : should be "energymicro,efm32-i2c"
- - interrupts : the interrupt number
- - clocks : reference to the module clock
-
-Recommended properties :
-
- - clock-frequency : maximal I2C bus clock frequency in Hz.
- - energymicro,location : Decides the location of the USART I/O pins.
- Allowed range : [0 .. 6]
-
-Example:
- i2c0: i2c@4000a000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "energymicro,efm32-i2c";
- reg = <0x4000a000 0x400>;
- interrupts = <9>;
- clocks = <&cmu clk_HFPERCLKI2C0>;
- clock-frequency = <100000>;
- energymicro,location = <3>;
-
- eeprom@50 {
- compatible = "microchip,24c02";
- reg = <0x50>;
- pagesize = <16>;
- };
- };
-
deleted file mode 100644
@@ -1,20 +0,0 @@
-* Energymicro efm32 UART
-
-Required properties:
-- compatible : Should be "energymicro,efm32-uart"
-- reg : Address and length of the register set
-- interrupts : Should contain uart interrupt
-
-Optional properties:
-- energymicro,location : Decides the location of the USART I/O pins.
- Allowed range : [0 .. 5]
- Default: 0
-
-Example:
-
-uart@4000c400 {
- compatible = "energymicro,efm32-uart";
- reg = <0x4000c400 0x400>;
- interrupts = <15>;
- energymicro,location = <0>;
-};
deleted file mode 100644
@@ -1,39 +0,0 @@
-* Energy Micro EFM32 SPI
-
-Required properties:
-- #address-cells: see spi-bus.txt
-- #size-cells: see spi-bus.txt
-- compatible: should be "energymicro,efm32-spi"
-- reg: Offset and length of the register set for the controller
-- interrupts: pair specifying rx and tx irq
-- clocks: phandle to the spi clock
-- cs-gpios: see spi-bus.txt
-
-Recommended properties :
-- energymicro,location: Value to write to the ROUTE register's LOCATION
- bitfield to configure the pinmux for the device, see
- datasheet for values.
- If this property is not provided, keeping what is
- already configured in the hardware, so its either the
- reset default 0 or whatever the bootloader did.
-
-Example:
-
-spi1: spi@4000c400 { /* USART1 */
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "energymicro,efm32-spi";
- reg = <0x4000c400 0x400>;
- interrupts = <15 16>;
- clocks = <&cmu 20>;
- cs-gpios = <&gpio 51 1>; // D3
- energymicro,location = <1>;
-
- ks8851@0 {
- compatible = "ks8851";
- spi-max-frequency = <6000000>;
- reg = <0>;
- interrupt-parent = <&boardfpga>;
- interrupts = <4>;
- };
-};
deleted file mode 100644
@@ -1,43 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __DT_BINDINGS_CLOCK_EFM32_CMU_H
-#define __DT_BINDINGS_CLOCK_EFM32_CMU_H
-
-#define clk_HFXO 0
-#define clk_HFRCO 1
-#define clk_LFXO 2
-#define clk_LFRCO 3
-#define clk_ULFRCO 4
-#define clk_AUXHFRCO 5
-#define clk_HFCLKNODIV 6
-#define clk_HFCLK 7
-#define clk_HFPERCLK 8
-#define clk_HFCORECLK 9
-#define clk_LFACLK 10
-#define clk_LFBCLK 11
-#define clk_WDOGCLK 12
-#define clk_HFCORECLKDMA 13
-#define clk_HFCORECLKAES 14
-#define clk_HFCORECLKUSBC 15
-#define clk_HFCORECLKUSB 16
-#define clk_HFCORECLKLE 17
-#define clk_HFCORECLKEBI 18
-#define clk_HFPERCLKUSART0 19
-#define clk_HFPERCLKUSART1 20
-#define clk_HFPERCLKUSART2 21
-#define clk_HFPERCLKUART0 22
-#define clk_HFPERCLKUART1 23
-#define clk_HFPERCLKTIMER0 24
-#define clk_HFPERCLKTIMER1 25
-#define clk_HFPERCLKTIMER2 26
-#define clk_HFPERCLKTIMER3 27
-#define clk_HFPERCLKACMP0 28
-#define clk_HFPERCLKACMP1 29
-#define clk_HFPERCLKI2C0 30
-#define clk_HFPERCLKI2C1 31
-#define clk_HFPERCLKGPIO 32
-#define clk_HFPERCLKVCMP 33
-#define clk_HFPERCLKPRS 34
-#define clk_HFPERCLKADC0 35
-#define clk_HFPERCLKDAC0 36
-
-#endif /* __DT_BINDINGS_CLOCK_EFM32_CMU_H */
Commit cc6111375cec ("ARM: drop efm32 platform") removed the platform, so no need to still carry the bindings. Signed-off-by: Wolfram Sang <wsa@kernel.org> --- .../devicetree/bindings/clock/efm32-clock.txt | 11 ----- .../devicetree/bindings/i2c/i2c-efm32.txt | 33 -------------- .../devicetree/bindings/serial/efm32-uart.txt | 20 --------- .../devicetree/bindings/spi/efm32-spi.txt | 39 ----------------- include/dt-bindings/clock/efm32-cmu.h | 43 ------------------- 5 files changed, 146 deletions(-) delete mode 100644 Documentation/devicetree/bindings/clock/efm32-clock.txt delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-efm32.txt delete mode 100644 Documentation/devicetree/bindings/serial/efm32-uart.txt delete mode 100644 Documentation/devicetree/bindings/spi/efm32-spi.txt delete mode 100644 include/dt-bindings/clock/efm32-cmu.h