| Message ID | 20220613111146.25221-6-peterwu.pub@gmail.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | Add Mediatek MT6370 PMIC support | expand |
On 13/06/2022 04:11, ChiaEn Wu wrote: > From: ChiYuan Huang <cy_huang@richtek.com> > > Add mt6370 backlight binding documentation. > > Signed-off-by: ChiYuan Huang <cy_huang@richtek.com> > --- > .../backlight/mediatek,mt6370-backlight.yaml | 107 ++++++++++++++++++ > 1 file changed, 107 insertions(+) > create mode 100644 Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml > > diff --git a/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml > new file mode 100644 > index 000000000000..25a05e607e83 > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml > @@ -0,0 +1,107 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/leds/backlight/mediatek,mt6370-backlight.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Mediatek MT6370 Backlight > + > +maintainers: > + - ChiaEn Wu <chiaen_wu@richtek.com> > + > +description: | > + This module is part of the MT6370 MFD device. > + The MT6370 Backlight WLED driver supports up to a 29V output voltage for > + 4 channels of 8 series WLEDs. Each channel supports up to 30mA of current > + capability with 2048 current steps (11 bits) in exponential or linear > + mapping curves. > + > +allOf: > + - $ref: common.yaml# > + > +properties: > + compatible: > + const: mediatek,mt6370-backlight > + > + default-brightness: > + minimum: 0 > + maximum: 2048 > + > + max-brightness: > + minimum: 0 > + maximum: 2048 > + > + enable-gpios: > + description: External backlight 'enable' pin > + maxItems: 1 > + > + mediatek,bled-pwm-enable: > + description: | > + Enable external PWM input for backlight dimming > + type: boolean > + > + mediatek,bled-pwm-hys-enable: > + description: | > + Enable the backlight input-hysteresis for PWM mode > + type: boolean > + > + mediatek,bled-pwm-hys-input-bit: > + $ref: /schemas/types.yaml#/definitions/uint8 > + enum: [0, 1, 2, 3] > + description: | > + The selection of the upper and lower bounds threshold of backlight > + PWM resolution. If we choose selection 3 (6 bits), the variation of PWM > + resolution needs over than 64 steps (2^6). > + value mapping: > + - 0: 1 > + - 1: 2 > + - 2: 4 > + - 3: 6 Nope, I said last time: "In any case you cannot have values mapping" Please use proper real world value, not some register bits. The property name also needs fixing. > + > + mediatek,bled-ovp-shutdown: > + description: | > + Enable the backlight shutdown when OVP level triggered > + type: boolean > + > + mediatek,bled-ovp-microvolt: > + enum: [0, 1, 2, 3] > + description: | > + Backlight OVP level selection. > + value mapping: > + - 0: 17000000 > + - 1: 21000000 > + - 2: 25000000 > + - 3: 29000000 No. Please test your bindings. microvolt cannot be 1 mV. It's 21000000, not 1. No value mappings. > + > + mediatek,bled-ocp-shutdown: > + description: | > + Enable the backlight shutdown when OCP level triggerred. > + type: boolean > + > + mediatek,bled-ocp-microamp: > + enum: [0, 1, 2, 3] > + description: | > + Backlight OC level selection. > + value mapping: > + - 0: 900000 > + - 1: 1200000 > + - 2: 1500000 > + - 3: 1800000 Nope. > + > + mediatek,bled-channel-use: > + $ref: /schemas/types.yaml#/definitions/uint8 > + description: | > + Backlight LED channel to be used. > + Each bit mapping to: > + - 0: CH4 > + - 1: CH3 > + - 2: CH2 > + - 3: CH1 > + minimum: 1 > + maximum: 15 > + > +required: > + - compatible > + - mediatek,bled-channel-use > + > +additionalProperties: false Best regards, Krzysztof
Hi Krzysztof, Thanks for your helpful feedback, I have some questions want to confirm with you below. Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> 於 2022年6月17日 週五 清晨5:13寫道： > > On 13/06/2022 04:11, ChiaEn Wu wrote: > > From: ChiYuan Huang <cy_huang@richtek.com> > > > > Add mt6370 backlight binding documentation. > > > > Signed-off-by: ChiYuan Huang <cy_huang@richtek.com> > > --- > > .../backlight/mediatek,mt6370-backlight.yaml | 107 ++++++++++++++++++ > > 1 file changed, 107 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml > > > > diff --git a/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml > > new file mode 100644 > > index 000000000000..25a05e607e83 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml > > @@ -0,0 +1,107 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/leds/backlight/mediatek,mt6370-backlight.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Mediatek MT6370 Backlight > > + > > +maintainers: > > + - ChiaEn Wu <chiaen_wu@richtek.com> > > + > > +description: | > > + This module is part of the MT6370 MFD device. > > + The MT6370 Backlight WLED driver supports up to a 29V output voltage for > > + 4 channels of 8 series WLEDs. Each channel supports up to 30mA of current > > + capability with 2048 current steps (11 bits) in exponential or linear > > + mapping curves. > > + > > +allOf: > > + - $ref: common.yaml# > > + > > +properties: > > + compatible: > > + const: mediatek,mt6370-backlight > > + > > + default-brightness: > > + minimum: 0 > > + maximum: 2048 > > + > > + max-brightness: > > + minimum: 0 > > + maximum: 2048 > > + > > + enable-gpios: > > + description: External backlight 'enable' pin > > + maxItems: 1 > > + > > + mediatek,bled-pwm-enable: > > + description: | > > + Enable external PWM input for backlight dimming > > + type: boolean > > + > > + mediatek,bled-pwm-hys-enable: > > + description: | > > + Enable the backlight input-hysteresis for PWM mode > > + type: boolean > > + > > + mediatek,bled-pwm-hys-input-bit: > > + $ref: /schemas/types.yaml#/definitions/uint8 > > + enum: [0, 1, 2, 3] > > + description: | > > + The selection of the upper and lower bounds threshold of backlight > > + PWM resolution. If we choose selection 3 (6 bits), the variation of PWM > > + resolution needs over than 64 steps (2^6). > > + value mapping: > > + - 0: 1 > > + - 1: 2 > > + - 2: 4 > > + - 3: 6 > > Nope, I said last time: > "In any case you cannot have values mapping" > > Please use proper real world value, not some register bits. The property > name also needs fixing. I so apologized for misunderstanding your meaning... I try to modify it like below. -------- mediatek,bled-pwm-hys-input-threshold-steps: $ref: /schemas/types.yaml#/definitions/uint8 enum: [1, 4, 16, 64] description: | The selection of the upper and lower bounds threshold of backlight PWM resolution. If we choose selection 64, the variation of PWM resolution needs over 64 steps. -------- If these changes meet your expectations, I will try to modify "bled-ovp-microvolt" and "bled-ocp-microamp" in the same way. Thank you so much. > > > + > > + mediatek,bled-ovp-shutdown: > > + description: | > > + Enable the backlight shutdown when OVP level triggered > > + type: boolean > > + > > + mediatek,bled-ovp-microvolt: > > + enum: [0, 1, 2, 3] > > + description: | > > + Backlight OVP level selection. > > + value mapping: > > + - 0: 17000000 > > + - 1: 21000000 > > + - 2: 25000000 > > + - 3: 29000000 > > No. Please test your bindings. > > microvolt cannot be 1 mV. It's 21000000, not 1. No value mappings. > > > + > > + mediatek,bled-ocp-shutdown: > > + description: | > > + Enable the backlight shutdown when OCP level triggerred. > > + type: boolean > > + > > + mediatek,bled-ocp-microamp: > > + enum: [0, 1, 2, 3] > > + description: | > > + Backlight OC level selection. > > + value mapping: > > + - 0: 900000 > > + - 1: 1200000 > > + - 2: 1500000 > > + - 3: 1800000 > > Nope. > > > + > > + mediatek,bled-channel-use: > > + $ref: /schemas/types.yaml#/definitions/uint8 > > + description: | > > + Backlight LED channel to be used. > > + Each bit mapping to: > > + - 0: CH4 > > + - 1: CH3 > > + - 2: CH2 > > + - 3: CH1 > > + minimum: 1 > > + maximum: 15 > > + > > +required: > > + - compatible > > + - mediatek,bled-channel-use > > + > > +additionalProperties: false > > > Best regards, > Krzysztof Best regards, ChiaEn Wu
On 17/06/2022 03:35, ChiaEn Wu wrote: > + - 3: 6 >> >> Nope, I said last time: >> "In any case you cannot have values mapping" >> >> Please use proper real world value, not some register bits. The property >> name also needs fixing. > > I so apologized for misunderstanding your meaning... > I try to modify it like below. > -------- > mediatek,bled-pwm-hys-input-threshold-steps: > $ref: /schemas/types.yaml#/definitions/uint8 > enum: [1, 4, 16, 64] > description: | > The selection of the upper and lower bounds threshold of backlight > PWM resolution. If we choose selection 64, the variation of PWM > resolution needs over 64 steps. > -------- > If these changes meet your expectations, I will try to modify > "bled-ovp-microvolt" and "bled-ocp-microamp" in the same way. > Thank you so much. > This looks good. Thank you. Best regards, Krzysztof
diff --git a/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml new file mode 100644 index 000000000000..25a05e607e83 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/mediatek,mt6370-backlight.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/backlight/mediatek,mt6370-backlight.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT6370 Backlight + +maintainers: + - ChiaEn Wu <chiaen_wu@richtek.com> + +description: | + This module is part of the MT6370 MFD device. + The MT6370 Backlight WLED driver supports up to a 29V output voltage for + 4 channels of 8 series WLEDs. Each channel supports up to 30mA of current + capability with 2048 current steps (11 bits) in exponential or linear + mapping curves. + +allOf: + - $ref: common.yaml# + +properties: + compatible: + const: mediatek,mt6370-backlight + + default-brightness: + minimum: 0 + maximum: 2048 + + max-brightness: + minimum: 0 + maximum: 2048 + + enable-gpios: + description: External backlight 'enable' pin + maxItems: 1 + + mediatek,bled-pwm-enable: + description: | + Enable external PWM input for backlight dimming + type: boolean + + mediatek,bled-pwm-hys-enable: + description: | + Enable the backlight input-hysteresis for PWM mode + type: boolean + + mediatek,bled-pwm-hys-input-bit: + $ref: /schemas/types.yaml#/definitions/uint8 + enum: [0, 1, 2, 3] + description: | + The selection of the upper and lower bounds threshold of backlight + PWM resolution. If we choose selection 3 (6 bits), the variation of PWM + resolution needs over than 64 steps (2^6). + value mapping: + - 0: 1 + - 1: 2 + - 2: 4 + - 3: 6 + + mediatek,bled-ovp-shutdown: + description: | + Enable the backlight shutdown when OVP level triggered + type: boolean + + mediatek,bled-ovp-microvolt: + enum: [0, 1, 2, 3] + description: | + Backlight OVP level selection. + value mapping: + - 0: 17000000 + - 1: 21000000 + - 2: 25000000 + - 3: 29000000 + + mediatek,bled-ocp-shutdown: + description: | + Enable the backlight shutdown when OCP level triggerred. + type: boolean + + mediatek,bled-ocp-microamp: + enum: [0, 1, 2, 3] + description: | + Backlight OC level selection. + value mapping: + - 0: 900000 + - 1: 1200000 + - 2: 1500000 + - 3: 1800000 + + mediatek,bled-channel-use: + $ref: /schemas/types.yaml#/definitions/uint8 + description: | + Backlight LED channel to be used. + Each bit mapping to: + - 0: CH4 + - 1: CH3 + - 2: CH2 + - 3: CH1 + minimum: 1 + maximum: 15 + +required: + - compatible + - mediatek,bled-channel-use + +additionalProperties: false