diff mbox series

[v4,3/3] arm64: dts: freescale: Add phyBOARD-Polis-i.MX8MM support

Message ID 20220623144124.1821570-3-t.remmet@phytec.de (mailing list archive)
State New, archived
Headers show
Series [v4,1/3] bindings: arm: fsl: Add PHYTEC i.MX8MM devicetree bindings | expand

Commit Message

Teresa Remmet June 23, 2022, 2:41 p.m. UTC 
Add initial support for phyBOARD-Polis-i.MX8MM.
Main features are:
	* Bluetooth and Wifi
	* CANFD
	* eMMC
	* i2c RTC
	* Ethernet
	* PCIe
	* RS232/RS485
	* SD-Card
	* SPI-NOR flash
	* USB

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
---
Changes in v4:
- Do not modify reserved iomux bits
- Remove eth phy irq due to a recent found hw issue on SoM

Changes in v3:
- move "enable-active-high" after "gpio" property
- Add missing newlines before child nodes
- sort i2c devices by address

Changes in v2:
- added missing space in compatible of imx8mm-phyboard-polis-rdk
- removed underscores in node names
- fixed indentation of reg_usdhc2_vmmc node
- put status always as last property of nodes
- updated node name of sn65dsi83 to bridge
---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 .../freescale/imx8mm-phyboard-polis-rdk.dts   | 450 ++++++++++++++++++
 .../dts/freescale/imx8mm-phycore-som.dtsi     | 440 +++++++++++++++++
 3 files changed, 891 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi

Comments

Shawn Guo June 27, 2022, 8:13 a.m. UTC | #1 
On Thu, Jun 23, 2022 at 04:41:24PM +0200, Teresa Remmet wrote:
> Add initial support for phyBOARD-Polis-i.MX8MM.
> Main features are:
> 	* Bluetooth and Wifi
> 	* CANFD
> 	* eMMC
> 	* i2c RTC
> 	* Ethernet
> 	* PCIe
> 	* RS232/RS485
> 	* SD-Card
> 	* SPI-NOR flash
> 	* USB
> 
> Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> ---
> Changes in v4:
> - Do not modify reserved iomux bits
> - Remove eth phy irq due to a recent found hw issue on SoM

Replaced v3 with this version.

In the future, please give a reply to the old version saying there is
a new version posted, so that I know the old one should be ignored.

Shawn
Teresa Remmet June 27, 2022, 8:28 a.m. UTC | #2 
Am Montag, dem 27.06.2022 um 16:13 +0800 schrieb Shawn Guo:
> On Thu, Jun 23, 2022 at 04:41:24PM +0200, Teresa Remmet wrote:
> > Add initial support for phyBOARD-Polis-i.MX8MM.
> > Main features are:
> > 	* Bluetooth and Wifi
> > 	* CANFD
> > 	* eMMC
> > 	* i2c RTC
> > 	* Ethernet
> > 	* PCIe
> > 	* RS232/RS485
> > 	* SD-Card
> > 	* SPI-NOR flash
> > 	* USB
> > 
> > Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
> > ---
> > Changes in v4:
> > - Do not modify reserved iomux bits
> > - Remove eth phy irq due to a recent found hw issue on SoM
> 
> Replaced v3 with this version.
> 
> In the future, please give a reply to the old version saying there is
> a new version posted, so that I know the old one should be ignored.

Okay I will, thank you.

Regards,
Teresa

> 
> Shawn
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 238a83e5b8c6..1e25dec2109b 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -58,6 +58,7 @@  dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts
new file mode 100644
index 000000000000..4a3df2b77b0b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts
@@ -0,0 +1,450 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+#include "imx8mm-phycore-som.dtsi"
+
+/ {
+	model = "PHYTEC phyBOARD-Polis-i.MX8MM RDK";
+	compatible = "phytec,imx8mm-phyboard-polis-rdk",
+		     "phytec,imx8mm-phycore-som", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	bt_osc_32k: bt-lp-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "bt_osc_32k";
+		#clock-cells = <0>;
+	};
+
+	can_osc_40m: can-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <40000000>;
+		clock-output-names = "can_osc_40m";
+		#clock-cells = <0>;
+	};
+
+	fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <0     0
+				      13000 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan>;
+		#cooling-cells = <2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc2";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_CPU;
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	usdhc1_pwrseq: pwr-seq {
+		compatible = "mmc-pwrseq-simple";
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <60>;
+		reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_can_en: regulator-can-en {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "CAN_EN";
+		startup-delay-us = <20>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1 {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1pwrgrp>;
+		regulator-name = "usb_otg1_vbus";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		off-on-delay-us = <20000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VSD_3V3";
+	};
+
+	reg_vcc_3v3: regulator-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_3V3";
+	};
+};
+
+/* SPI - CAN MCP251XFD */
+&ecspi1 {
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	can0: can@0 {
+		compatible = "microchip,mcp251xfd";
+		clocks = <&can_osc_40m>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_int>;
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		xceiver-supply = <&reg_can_en>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "nINT_ETHPHY", "LED_RED", "WDOG_INT", "X_RTC_INT",
+		"", "", "", "RESET_ETHPHY",
+		"CAN_nINT", "CAN_EN", "nENABLE_FLATLINK", "",
+		"USB_OTG_VBUS_EN", "", "LED_GREEN", "LED_BLUE";
+};
+
+&gpio2 {
+	gpio-line-names = "", "", "", "",
+		"", "", "BT_REG_ON", "WL_REG_ON",
+		"BT_DEV_WAKE", "BT_HOST_WAKE", "", "",
+		"X_SD2_CD_B", "", "", "",
+		"", "", "", "SD2_RESET_B";
+};
+
+&gpio4 {
+	gpio-line-names = "", "", "", "",
+		"", "", "", "",
+		"FAN", "miniPCIe_nPERST", "", "",
+		"COEX1", "COEX2";
+};
+
+&gpio5 {
+	gpio-line-names = "", "", "", "",
+		"", "", "", "",
+		"", "ECSPI1_SS0";
+};
+
+/* PCIe */
+&pcie0 {
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&clk IMX8MM_CLK_PCIE1_PHY>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio4 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pcie_phy {
+	clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
+	fsl,clkreq-unsupported;
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
+	fsl,tx-deemph-gen1 = <0x2d>;
+	fsl,tx-deemph-gen2 = <0xf>;
+	status = "okay";
+};
+
+&rv3028 {
+	trickle-resistor-ohms = <3000>;
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* UART - RS232/RS485 */
+&uart1 {
+	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* UART - Sterling-LWB Bluetooth */
+&uart2 {
+	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_bt>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&bt_osc_32k>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
+		interrupt-names = "host-wakeup";
+		interrupt-parent = <&gpio2>;
+		interrupts = <9 IRQ_TYPE_EDGE_BOTH>;
+		max-speed = <2000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bt>;
+		shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+		vddio-supply = <&reg_vcc_3v3>;
+	};
+};
+
+/* UART - console */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+/* USB */
+&usbotg1 {
+	adp-disable;
+	dr_mode = "otg";
+	over-current-active-low;
+	samsung,picophy-pre-emp-curr-control = <3>;
+	samsung,picophy-dc-vol-level-adjust = <7>;
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current;
+	dr_mode = "host";
+	samsung,picophy-pre-emp-curr-control = <3>;
+	samsung,picophy-dc-vol-level-adjust = <7>;
+	status = "okay";
+};
+
+/* SDIO - Sterling-LWB Wifi */
+&usdhc1 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC1>;
+	assigned-clock-rates = <200000000>;
+	bus-width = <4>;
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+	non-removable;
+	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_wlan>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+/* SD-Card */
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+	assigned-clock-rates = <200000000>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	vqmmc-supply = <&reg_nvcc_sd2>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6	0x00
+			MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8	0x00
+			MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9	0x00
+		>;
+	};
+
+	pinctrl_can_en: can-engrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x00
+		>;
+	};
+
+	pinctrl_can_int: can-intgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8	0x00
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x80
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x80
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x80
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9	0x00
+		>;
+	};
+
+	pinctrl_fan: fan0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8	0x16
+		>;
+	};
+
+	pinctrl_leds: leds1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1	0x16
+			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14	0x16
+			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x16
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9	0x00
+			MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12	0x12
+			MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19	0x12
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x40
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX	0x00
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B	0x00
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX	0x00
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B	0x00
+		>;
+	};
+
+	pinctrl_uart2_bt: uart2btgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DTE_RTS_B	0x00
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_CTS_B	0x00
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX	0x00
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX	0x00
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX	0x40
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x40
+		>;
+	};
+
+	pinctrl_usbotg1pwrgrp: usbotg1pwrgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x00
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x182
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0xc6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0	0xc6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1	0xc6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2	0xc6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3	0xc6
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12	0x40
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x192
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d2
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d2
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d2
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d2
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d2
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d6
+		>;
+	};
+
+	pinctrl_wlan: wlangrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA5_GPIO2_IO7	0x00
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
new file mode 100644
index 000000000000..995b44efb1b6
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
@@ -0,0 +1,440 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ */
+
+#include "imx8mm.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	model = "PHYTEC phyCORE-i.MX8MM";
+	compatible = "phytec,imx8mm-phycore-som", "fsl,imx8mm";
+
+	aliases {
+		rtc0 = &rv3028;
+		rtc1 = &snvs_rtc;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	reg_vdd_3v3_s: regulator-vdd-3v3-s {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VDD_3V3_S";
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+/* Ethernet */
+&fec1 {
+	fsl,magic-packet;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			enet-phy-lane-no-swap;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			reg = <0>;
+			reset-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+		};
+	};
+};
+
+/* SPI Flash */
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+	status = "okay";
+
+	som_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "nINT_ETHPHY", "", "WDOG_INT", "X_RTC_INT",
+		"", "", "", "RESET_ETHPHY",
+		"", "", "nENABLE_FLATLINK";
+};
+
+/* I2C1 */
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default","gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "nxp,pf8121a";
+		reg = <0x08>;
+
+		regulators {
+			reg_nvcc_sd1: ldo1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "NVCC_SD1 (LDO1)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_nvcc_sd2: ldo2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "NVCC_SD2 (LDO2)";
+				vselect-en;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vcc_enet: ldo3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <2500000>;
+				regulator-min-microvolt = <1500000>;
+				regulator-name = "VCC_ENET_2V5 (LDO3)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vdda_1v8: ldo4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1500000>;
+				regulator-name = "VDDA_1V8 (LDO4)";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-min-microvolt = <1500000>;
+					regulator-suspend-max-microvolt = <1500000>;
+				};
+			};
+
+			reg_soc_vdda_phy: buck1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <400000>;
+				regulator-name = "VDD_SOC_VDDA_PHY_0P8 (BUCK1)";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-min-microvolt = <400000>;
+					regulator-suspend-max-microvolt = <400000>;
+				};
+			};
+
+			reg_vdd_gpu_dram: buck2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1000000>;
+				regulator-min-microvolt = <1000000>;
+				regulator-name = "VDD_GPU_DRAM (BUCK2)";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1000000>;
+					regulator-suspend-min-microvolt = <1000000>;
+				};
+			};
+
+			reg_vdd_gpu: buck3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1000000>;
+				regulator-min-microvolt = <400000>;
+				regulator-name = "VDD_VPU (BUCK3)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vdd_mipi: buck4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1050000>;
+				regulator-min-microvolt = <900000>;
+				regulator-name = "VDD_MIPI_0P9 (BUCK4)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vdd_arm: buck5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1050000>;
+				regulator-min-microvolt = <400000>;
+				regulator-name = "VDD_ARM (BUCK5)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vdd_1v8: buck6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "VDD_1V8 (BUCK6)";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1800000>;
+					regulator-suspend-min-microvolt = <1800000>;
+				};
+			};
+
+			reg_nvcc_dram: buck7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1100000>;
+				regulator-name = "NVCC_DRAM_1P1V (BUCK7)";
+			};
+
+			reg_vsnvs: vsnvs {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "NVCC_SNVS_1P8 (VSNVS)";
+			};
+		};
+	};
+
+	sn65dsi83: bridge@2d {
+		compatible = "ti,sn65dsi83";
+		enable-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sn65dsi83>;
+		reg = <0x2d>;
+		status = "disabled";
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c32";
+		pagesize = <32>;
+		reg = <0x51>;
+		vcc-supply = <&reg_vdd_3v3_s>;
+	};
+
+	rv3028: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		reg = <0x52>;
+	};
+};
+
+/* EMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	keep-power-in-suspend;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	non-removable;
+	status = "okay";
+};
+
+/* Watchdog */
+&wdog1 {
+	fsl,ext-reset-output;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x2
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x2
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x90
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x90
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x90
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x90
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x90
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x90
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x16
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x16
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x16
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x16
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x16
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x16
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x10
+		>;
+	};
+
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x1c2
+			MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B		0x82
+			MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0		0x82
+			MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1		0x82
+			MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2		0x82
+			MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3		0x82
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c0
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c0
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x1e0
+			MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x1e0
+		>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x1c0
+		>;
+	};
+
+	pinctrl_sn65dsi83: sn65dsi83grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d0
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x190
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d0
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d0
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d0
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d0
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d0
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d0
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d0
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x190
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x194
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d6
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x196
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d6
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d6
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d6
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d6
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d6
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d6
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d6
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0x26
+		>;
+	};
+};