diff mbox series

[v3,5/5] arm64: dts: qcom: add SA8540P and ADP

Message ID 20220629041438.1352536-6-bjorn.andersson@linaro.org (mailing list archive)
State Accepted
Headers show
Series arm64: dts: qcom: Introduce SC8280XP | expand

Commit Message

Bjorn Andersson June 29, 2022, 4:14 a.m. UTC 
Introduce the Qualcomm SA8540P automotive platform and the SA8295P ADP
development board.

The SA8540P and SC8280XP are fairly similar, so the SA8540P is built
ontop of the SC8280XP dtsi to reduce duplication. As more advanced
features are integrated this might be re-evaluated.

This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
regulators, debug UART, PMICs, remoteprocs (NSPs crashes shortly after
booting) and USB.

The SA8295P ADP contains four PM8450 PMICs, which according to their
revid are compatible with PM8150. They are defined within the ADP for
now, to avoid creating additional .dtsi files for PM8150 with just
addresses changed - and to allow using the labels from the schematics.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
---

Changes since v2:
- Sorted "status" property last throughout the patch
- Dropped empty reserved-memory node
- Dropped multiport vbus-enable pinctrl states for now

 arch/arm64/boot/dts/qcom/Makefile        |   1 +
 arch/arm64/boot/dts/qcom/sa8295p-adp.dts | 406 +++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sa8540p.dtsi    | 133 ++++++++
 3 files changed, 540 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sa8295p-adp.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sa8540p.dtsi

Comments

Johan Hovold June 29, 2022, 7:45 a.m. UTC | #1 
On Tue, Jun 28, 2022 at 09:14:38PM -0700, Bjorn Andersson wrote:
> Introduce the Qualcomm SA8540P automotive platform and the SA8295P ADP
> development board.
> 
> The SA8540P and SC8280XP are fairly similar, so the SA8540P is built
> ontop of the SC8280XP dtsi to reduce duplication. As more advanced
> features are integrated this might be re-evaluated.
> 
> This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
> regulators, debug UART, PMICs, remoteprocs (NSPs crashes shortly after
> booting) and USB.
> 
> The SA8295P ADP contains four PM8450 PMICs, which according to their
> revid are compatible with PM8150. They are defined within the ADP for
> now, to avoid creating additional .dtsi files for PM8150 with just
> addresses changed - and to allow using the labels from the schematics.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
> ---
> 
> Changes since v2:
> - Sorted "status" property last throughout the patch
> - Dropped empty reserved-memory node
> - Dropped multiport vbus-enable pinctrl states for now

> +/* PINCTRL */
> +&pm8450c_gpios {
> +	usb2_en_state: usb2-en-state {
> +		pins = "gpio9";
> +		function = "normal";
> +		output-high;
> +		power-source = <0>;
> +	};
> +};
> +
> +&pm8450e_gpios {
> +	usb3_en_state: usb3-en-state {
> +		pins = "gpio5";
> +		function = "normal";
> +		output-high;
> +		power-source = <0>;
> +	};
> +};

You forgot to remove these two when you removed the other multiport
vbus-enable states.

Looks good otherwise.

Johan
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index ceeae094a59f..2f416b84b71c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -52,6 +52,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
new file mode 100644
index 000000000000..d4baa2460e4a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
@@ -0,0 +1,406 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/spmi/spmi.h>
+
+#include "sa8540p.dtsi"
+
+/ {
+	model = "Qualcomm SA8295P ADP";
+	compatible = "qcom,sa8295p-adp", "qcom,sa8540p";
+
+	aliases {
+		serial0 = &qup2_uart17;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&apps_rsc {
+	pmm8540-a-regulators {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_l3a: ldo3 {
+			regulator-name = "vreg_l3a";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-name = "vreg_l5a";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-name = "vreg_l7a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l13a: ldo13 {
+			regulator-name = "vreg_l13a";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+	};
+
+	pmm8540-c-regulators {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l2c: ldo2 {
+			regulator-name = "vreg_l2c";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l3c: ldo3 {
+			regulator-name = "vreg_l3c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4c: ldo4 {
+			regulator-name = "vreg_l4c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6c: ldo6 {
+			regulator-name = "vreg_l6c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-name = "vreg_l7c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l10c: ldo10 {
+			regulator-name = "vreg_l10c";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l17c: ldo17 {
+			regulator-name = "vreg_l17c";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+	};
+
+	pmm8540-g-regulators {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vreg_l3g: ldo3 {
+			regulator-name = "vreg_l3g";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7g: ldo7 {
+			regulator-name = "vreg_l7g";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l8g: ldo8 {
+			regulator-name = "vreg_l8g";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+	};
+};
+
+&qup2 {
+	status = "okay";
+};
+
+&qup2_uart17 {
+	compatible = "qcom,geni-debug-uart";
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sa8540p/adsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_nsp0 {
+	firmware-name = "qcom/sa8540p/cdsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_nsp1 {
+	firmware-name = "qcom/sa8540p/cdsp1.mbn";
+	status = "okay";
+};
+
+&spmi_bus {
+	pm8450a: pmic@0 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450a_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450c: pmic@4 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450c_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450e: pmic@8 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x8 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450e_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450g: pmic@c {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0xc SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450g_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l17c>;
+	vcc-max-microamp = <800000>;
+	vccq-supply = <&vreg_l6c>;
+	vccq-max-microamp = <900000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l8g>;
+	vdda-pll-supply = <&vreg_l3g>;
+
+	status = "okay";
+};
+
+&ufs_card_hc {
+	reset-gpios = <&tlmm 229 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l10c>;
+	vcc-max-microamp = <800000>;
+	vccq-supply = <&vreg_l3c>;
+	vccq-max-microamp = <900000>;
+
+	status = "okay";
+};
+
+&ufs_card_phy {
+	vdda-phy-supply = <&vreg_l8g>;
+	vdda-pll-supply = <&vreg_l3g>;
+
+	status = "okay";
+};
+
+&usb_0 {
+	status = "okay";
+};
+
+&usb_0_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "peripheral";
+};
+
+&usb_0_hsphy {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7a>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l3a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vreg_l1c>;
+	vdda18-supply = <&vreg_l7c>;
+	vdda33-supply = <&vreg_l2c>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l4c>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy0 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy1 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy2 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy3 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&usb_2_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&xo_board_clk {
+	clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
+&pm8450c_gpios {
+	usb2_en_state: usb2-en-state {
+		pins = "gpio9";
+		function = "normal";
+		output-high;
+		power-source = <0>;
+	};
+};
+
+&pm8450e_gpios {
+	usb3_en_state: usb3-en-state {
+		pins = "gpio5";
+		function = "normal";
+		output-high;
+		power-source = <0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sa8540p.dtsi b/arch/arm64/boot/dts/qcom/sa8540p.dtsi
new file mode 100644
index 000000000000..8ea2886fbab2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8540p.dtsi
@@ -0,0 +1,133 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include "sc8280xp.dtsi"
+
+/delete-node/ &cpu0_opp_table;
+/delete-node/ &cpu4_opp_table;
+
+/ {
+	cpu0_opp_table: cpu0-opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-403200000 {
+			opp-hz = /bits/ 64 <403200000>;
+		};
+		opp-499200000 {
+			opp-hz = /bits/ 64 <499200000>;
+		};
+		opp-595200000 {
+			opp-hz = /bits/ 64 <595200000>;
+		};
+		opp-710400000 {
+			opp-hz = /bits/ 64 <710400000>;
+		};
+		opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+		};
+		opp-1017600000 {
+			opp-hz = /bits/ 64 <1017600000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+		};
+		opp-1555200000 {
+			opp-hz = /bits/ 64 <1555200000>;
+		};
+		opp-1670400000 {
+			opp-hz = /bits/ 64 <1670400000>;
+		};
+		opp-1785600000 {
+			opp-hz = /bits/ 64 <1785600000>;
+		};
+		opp-1881600000 {
+			opp-hz = /bits/ 64 <1881600000>;
+		};
+		opp-2016000000 {
+			opp-hz = /bits/ 64 <2016000000>;
+		};
+		opp-2131200000 {
+			opp-hz = /bits/ 64 <2131200000>;
+		};
+		opp-2246400000 {
+			opp-hz = /bits/ 64 <2246400000>;
+		};
+	};
+
+	cpu4_opp_table: cpu4-opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-825600000 {
+			opp-hz = /bits/ 64 <825600000>;
+		};
+		opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+		};
+		opp-1171200000 {
+			opp-hz = /bits/ 64 <1171200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+		};
+		opp-1632000000 {
+			opp-hz = /bits/ 64 <1632000000>;
+		};
+		opp-1747200000 {
+			opp-hz = /bits/ 64 <1747200000>;
+		};
+		opp-1862400000 {
+			opp-hz = /bits/ 64 <1862400000>;
+		};
+		opp-1977600000 {
+			opp-hz = /bits/ 64 <1977600000>;
+		};
+		opp-2073600000 {
+			opp-hz = /bits/ 64 <2073600000>;
+		};
+		opp-2169600000 {
+			opp-hz = /bits/ 64 <2169600000>;
+		};
+		opp-2284800000 {
+			opp-hz = /bits/ 64 <2284800000>;
+		};
+		opp-2380800000 {
+			opp-hz = /bits/ 64 <2380800000>;
+		};
+		opp-2496000000 {
+			opp-hz = /bits/ 64 <2496000000>;
+		};
+		opp-2592000000 {
+			opp-hz = /bits/ 64 <2592000000>;
+		};
+	};
+};
+
+&rpmhpd {
+	compatible = "qcom,sa8540p-rpmhpd";
+};