| Message ID | 20220726180623.1668-7-prabhakar.mahadev-lad.rj@bp.renesas.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add support for Renesas RZ/Five SoC | expand |
Hey, Saw your other binding patches coming in earlier & wondered if this would show up today ;) On 26/07/2022 19:06, Lad Prabhakar wrote: > EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe > > Add initial device tree for Renesas RZ/Five RISC-V CPU Core (AX45MP > Single). > > Below is the list of IP blocks added in the initial SoC DTSI which can be > used to boot via initramfs on RZ/Five SMARC EVK: > - AX45MP CPU > - CPG > - PINCTRL > - PLIC > - SCIF0 > - SYSC > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > --- > arch/riscv/boot/dts/Makefile | 1 + > arch/riscv/boot/dts/renesas/r9a07g043.dtsi | 121 +++++++++++++++++++++ Missing files? Where is your Makefile for this directory? Or the board dts? Enabling CONFIG_SOC_RENESAS_RZFIVE causes dtbs_check to fail :( > 2 files changed, 122 insertions(+) > create mode 100644 arch/riscv/boot/dts/renesas/r9a07g043.dtsi > > diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile > index ff174996cdfd..b0ff5fbabb0c 100644 > --- a/arch/riscv/boot/dts/Makefile > +++ b/arch/riscv/boot/dts/Makefile > @@ -3,5 +3,6 @@ subdir-y += sifive > subdir-y += starfive > subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan > subdir-y += microchip > +subdir-y += renesas > > obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y)) > diff --git a/arch/riscv/boot/dts/renesas/r9a07g043.dtsi b/arch/riscv/boot/dts/renesas/r9a07g043.dtsi > new file mode 100644 > index 000000000000..6e0b640c6c7f > --- /dev/null > +++ b/arch/riscv/boot/dts/renesas/r9a07g043.dtsi > @@ -0,0 +1,121 @@ > +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +/* > + * Device Tree Source for the RZ/Five SoC > + * > + * Copyright (C) 2022 Renesas Electronics Corp. > + */ > + > +#include <dt-bindings/interrupt-controller/arm-gic.h> Including arm gic stuff on riscv? That seems a bit odd to me. > +#include <dt-bindings/clock/r9a07g043-cpg.h> > + > +/ { > + compatible = "renesas,r9a07g043"; > + #address-cells = <2>; > + #size-cells = <2>; > + > + /* clock can be either from exclk or crystal oscillator (XIN/XOUT) */ > + extal_clk: extal-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + /* This value must be overridden by the board */ > + clock-frequency = <0>; Why add the empty value in that case? > + }; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + timebase-frequency = <24000000>; > + > + ax45mp: cpu@0 { > + compatible = "andestech,ax45mp", "riscv"; > + device_type = "cpu"; > + reg = <0x0>; > + status = "okay"; > + riscv,isa = "rv64imafdc"; > + mmu-type = "riscv,sv39"; > + i-cache-size = <0x8000>; > + i-cache-line-size = <0x40>; > + d-cache-size = <0x8000>; > + d-cache-line-size = <0x40>; > + clocks = <&cpg CPG_CORE R9A07G043_AX45MP_CORE0_CLK>, > + <&cpg CPG_CORE R9A07G043_AX45MP_ACLK>; > + > + cpu0_intc: interrupt-controller { > + #interrupt-cells = <1>; > + compatible = "riscv,cpu-intc"; > + interrupt-controller; > + }; > + }; > + }; > + > + soc: soc { > + compatible = "simple-bus"; > + interrupt-parent = <&plic>; > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + scif0: serial@1004b800 { > + compatible = "renesas,scif-r9a07g043", > + "renesas,scif-r9a07g044"; > + reg = <0 0x1004b800 0 0x400>; > + interrupts = <412 IRQ_TYPE_LEVEL_HIGH>, > + <414 IRQ_TYPE_LEVEL_HIGH>, > + <415 IRQ_TYPE_LEVEL_HIGH>, > + <413 IRQ_TYPE_LEVEL_HIGH>, > + <416 IRQ_TYPE_LEVEL_HIGH>, > + <416 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "eri", "rxi", "txi", > + "bri", "dri", "tei"; > + clocks = <&cpg CPG_MOD R9A07G043_SCIF0_CLK_PCK>; > + clock-names = "fck"; > + power-domains = <&cpg>; > + resets = <&cpg R9A07G043_SCIF0_RST_SYSTEM_N>; > + status = "disabled"; > + }; > + > + cpg: clock-controller@11010000 { > + compatible = "renesas,r9a07g043-cpg"; > + reg = <0 0x11010000 0 0x10000>; > + clocks = <&extal_clk>; > + clock-names = "extal"; > + #clock-cells = <2>; > + #reset-cells = <1>; > + #power-domain-cells = <0>; > + }; > + > + sysc: system-controller@11020000 { > + compatible = "renesas,r9a07g043-sysc"; > + reg = <0 0x11020000 0 0x10000>; > + status = "disabled"; > + }; > + > + pinctrl: pinctrl@11030000 { > + compatible = "renesas,r9a07g043-pinctrl"; > + reg = <0 0x11030000 0 0x10000>; > + gpio-controller; > + #gpio-cells = <2>; > + #interrupt-cells = <2>; > + interrupt-controller; > + gpio-ranges = <&pinctrl 0 0 152>; > + clocks = <&cpg CPG_MOD R9A07G043_GPIO_HCLK>; > + power-domains = <&cpg>; > + resets = <&cpg R9A07G043_GPIO_RSTN>, > + <&cpg R9A07G043_GPIO_PORT_RESETN>, > + <&cpg R9A07G043_GPIO_SPARE_RESETN>; > + }; > + > + plic: interrupt-controller@12c00000 { > + compatible = "renesas,r9a07g043-plic", "andestech,nceplic100"; > + #interrupt-cells = <2>; > + #address-cells = <0>; > + riscv,ndev = <543>; > + interrupt-controller; > + reg = <0x0 0x12c00000 0 0x400000>; Does reg not usually get sorted after compatible? For consistency in this file it should at least. Thanks, Conor. > + clocks = <&cpg CPG_MOD R9A07G043_NCEPLIC_ACLK>; > + power-domains = <&cpg>; > + resets = <&cpg R9A07G043_NCEPLIC_ARESETN>; > + interrupts-extended = <&cpu0_intc 11 &cpu0_intc 9>; > + }; > + }; > +}; > -- > 2.17.1 > > > _______________________________________________ > linux-riscv mailing list > linux-riscv@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-riscv
On 26/07/2022 19:25, Conor.Dooley@microchip.com wrote: > Hey, > Saw your other binding patches coming in earlier & wondered if > this would show up today ;) > > On 26/07/2022 19:06, Lad Prabhakar wrote: >> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe >> >> Add initial device tree for Renesas RZ/Five RISC-V CPU Core (AX45MP >> Single). >> >> Below is the list of IP blocks added in the initial SoC DTSI which can be >> used to boot via initramfs on RZ/Five SMARC EVK: >> - AX45MP CPU >> - CPG >> - PINCTRL >> - PLIC >> - SCIF0 >> - SYSC >> >> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> >> --- >> arch/riscv/boot/dts/Makefile | 1 + >> arch/riscv/boot/dts/renesas/r9a07g043.dtsi | 121 +++++++++++++++++++++ > > Missing files? Where is your Makefile for this directory? > Or the board dts? > > Enabling CONFIG_SOC_RENESAS_RZFIVE causes dtbs_check to fail :( > FWIW, it breaks the dts build too even disabled b/c of the missing Makefile. Thanks, Conor.
Hi Conor, On Tue, Jul 26, 2022 at 7:25 PM <Conor.Dooley@microchip.com> wrote: > > Hey, > Saw your other binding patches coming in earlier & wondered if > this would show up today ;) > :) > On 26/07/2022 19:06, Lad Prabhakar wrote: > > EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe > > > > Add initial device tree for Renesas RZ/Five RISC-V CPU Core (AX45MP > > Single). > > > > Below is the list of IP blocks added in the initial SoC DTSI which can be > > used to boot via initramfs on RZ/Five SMARC EVK: > > - AX45MP CPU > > - CPG > > - PINCTRL > > - PLIC > > - SCIF0 > > - SYSC > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > --- > > arch/riscv/boot/dts/Makefile | 1 + > > arch/riscv/boot/dts/renesas/r9a07g043.dtsi | 121 +++++++++++++++++++++ > > Missing files? Where is your Makefile for this directory? > Or the board dts? > My plan was to get the initial minimal SoC DTSi and then later gradually add the board DTS, but it looks like I'll have to include it along with this series. > Enabling CONFIG_SOC_RENESAS_RZFIVE causes dtbs_check to fail :( > I shall include the Makefile and boards dts in v2 > > 2 files changed, 122 insertions(+) > > create mode 100644 arch/riscv/boot/dts/renesas/r9a07g043.dtsi > > > > diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile > > index ff174996cdfd..b0ff5fbabb0c 100644 > > --- a/arch/riscv/boot/dts/Makefile > > +++ b/arch/riscv/boot/dts/Makefile > > @@ -3,5 +3,6 @@ subdir-y += sifive > > subdir-y += starfive > > subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan > > subdir-y += microchip > > +subdir-y += renesas > > > > obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y)) > > diff --git a/arch/riscv/boot/dts/renesas/r9a07g043.dtsi b/arch/riscv/boot/dts/renesas/r9a07g043.dtsi > > new file mode 100644 > > index 000000000000..6e0b640c6c7f > > --- /dev/null > > +++ b/arch/riscv/boot/dts/renesas/r9a07g043.dtsi > > @@ -0,0 +1,121 @@ > > +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +/* > > + * Device Tree Source for the RZ/Five SoC > > + * > > + * Copyright (C) 2022 Renesas Electronics Corp. > > + */ > > + > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > Including arm gic stuff on riscv? That seems a bit odd to me. > Ouch this needs to be replaced with irq.h (required for IRQ_TYPE_LEVEL_* flags) > > +#include <dt-bindings/clock/r9a07g043-cpg.h> > > + > > +/ { > > + compatible = "renesas,r9a07g043"; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + > > + /* clock can be either from exclk or crystal oscillator (XIN/XOUT) */ > > + extal_clk: extal-clk { > > + compatible = "fixed-clock"; > > + #clock-cells = <0>; > > + /* This value must be overridden by the board */ > > + clock-frequency = <0>; > > Why add the empty value in that case? > For ARM64 SoC DTSI we use the above approach so f Iollowed the same, but you are right this can be dropped. > > + }; > > + > > + cpus { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + timebase-frequency = <24000000>; > > + > > + ax45mp: cpu@0 { > > + compatible = "andestech,ax45mp", "riscv"; > > + device_type = "cpu"; > > + reg = <0x0>; > > + status = "okay"; > > + riscv,isa = "rv64imafdc"; > > + mmu-type = "riscv,sv39"; > > + i-cache-size = <0x8000>; > > + i-cache-line-size = <0x40>; > > + d-cache-size = <0x8000>; > > + d-cache-line-size = <0x40>; > > + clocks = <&cpg CPG_CORE R9A07G043_AX45MP_CORE0_CLK>, > > + <&cpg CPG_CORE R9A07G043_AX45MP_ACLK>; > > + > > + cpu0_intc: interrupt-controller { > > + #interrupt-cells = <1>; > > + compatible = "riscv,cpu-intc"; > > + interrupt-controller; > > + }; > > + }; > > + }; > > + > > + soc: soc { > > + compatible = "simple-bus"; > > + interrupt-parent = <&plic>; > > + #address-cells = <2>; > > + #size-cells = <2>; > > + ranges; > > + > > + scif0: serial@1004b800 { > > + compatible = "renesas,scif-r9a07g043", > > + "renesas,scif-r9a07g044"; > > + reg = <0 0x1004b800 0 0x400>; > > + interrupts = <412 IRQ_TYPE_LEVEL_HIGH>, > > + <414 IRQ_TYPE_LEVEL_HIGH>, > > + <415 IRQ_TYPE_LEVEL_HIGH>, > > + <413 IRQ_TYPE_LEVEL_HIGH>, > > + <416 IRQ_TYPE_LEVEL_HIGH>, > > + <416 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-names = "eri", "rxi", "txi", > > + "bri", "dri", "tei"; > > + clocks = <&cpg CPG_MOD R9A07G043_SCIF0_CLK_PCK>; > > + clock-names = "fck"; > > + power-domains = <&cpg>; > > + resets = <&cpg R9A07G043_SCIF0_RST_SYSTEM_N>; > > + status = "disabled"; > > + }; > > + > > + cpg: clock-controller@11010000 { > > + compatible = "renesas,r9a07g043-cpg"; > > + reg = <0 0x11010000 0 0x10000>; > > + clocks = <&extal_clk>; > > + clock-names = "extal"; > > + #clock-cells = <2>; > > + #reset-cells = <1>; > > + #power-domain-cells = <0>; > > + }; > > + > > + sysc: system-controller@11020000 { > > + compatible = "renesas,r9a07g043-sysc"; > > + reg = <0 0x11020000 0 0x10000>; > > + status = "disabled"; > > + }; > > + > > + pinctrl: pinctrl@11030000 { > > + compatible = "renesas,r9a07g043-pinctrl"; > > + reg = <0 0x11030000 0 0x10000>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + #interrupt-cells = <2>; > > + interrupt-controller; > > + gpio-ranges = <&pinctrl 0 0 152>; > > + clocks = <&cpg CPG_MOD R9A07G043_GPIO_HCLK>; > > + power-domains = <&cpg>; > > + resets = <&cpg R9A07G043_GPIO_RSTN>, > > + <&cpg R9A07G043_GPIO_PORT_RESETN>, > > + <&cpg R9A07G043_GPIO_SPARE_RESETN>; > > + }; > > + > > + plic: interrupt-controller@12c00000 { > > + compatible = "renesas,r9a07g043-plic", "andestech,nceplic100"; > > + #interrupt-cells = <2>; > > + #address-cells = <0>; > > + riscv,ndev = <543>; > > + interrupt-controller; > > + reg = <0x0 0x12c00000 0 0x400000>; > > Does reg not usually get sorted after compatible? > For consistency in this file it should at least. > Agreed will fix that. Cheers, Prabhakar
On 27/07/2022 09:09, Lad, Prabhakar wrote: > Hi Conor, > >> >> Missing files? Where is your Makefile for this directory? >> Or the board dts? >> > My plan was to get the initial minimal SoC DTSi and then later > gradually add the board DTS, but it looks like I'll have to include it > along with this series. > You could still add a minimal dts & add more things to it over time I guess?
Hi Conor, On Wed, Jul 27, 2022 at 9:21 AM <Conor.Dooley@microchip.com> wrote: > > > On 27/07/2022 09:09, Lad, Prabhakar wrote: > > Hi Conor, > > > >> > >> Missing files? Where is your Makefile for this directory? > >> Or the board dts? > >> > > My plan was to get the initial minimal SoC DTSi and then later > > gradually add the board DTS, but it looks like I'll have to include it > > along with this series. > > > > You could still add a minimal dts & add more things to it over time I > guess? > Agreed. Cheers, Prabhakar
On 26/07/2022 20:06, Lad Prabhakar wrote: > Add initial device tree for Renesas RZ/Five RISC-V CPU Core (AX45MP > Single). > > Below is the list of IP blocks added in the initial SoC DTSI which can be > used to boot via initramfs on RZ/Five SMARC EVK: > - AX45MP CPU > - CPG > - PINCTRL > - PLIC > - SCIF0 > - SYSC > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > --- > arch/riscv/boot/dts/Makefile | 1 + > arch/riscv/boot/dts/renesas/r9a07g043.dtsi | 121 +++++++++++++++++++++ > 2 files changed, 122 insertions(+) > create mode 100644 arch/riscv/boot/dts/renesas/r9a07g043.dtsi > > diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile > index ff174996cdfd..b0ff5fbabb0c 100644 > --- a/arch/riscv/boot/dts/Makefile > +++ b/arch/riscv/boot/dts/Makefile > @@ -3,5 +3,6 @@ subdir-y += sifive > subdir-y += starfive > subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan > subdir-y += microchip > +subdir-y += renesas What are you building there? There is no DTS. Best regards, Krzysztof
Hi Krzysztof, On Wed, Jul 27, 2022 at 9:55 AM Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 26/07/2022 20:06, Lad Prabhakar wrote: > > Add initial device tree for Renesas RZ/Five RISC-V CPU Core (AX45MP > > Single). > > > > Below is the list of IP blocks added in the initial SoC DTSI which can be > > used to boot via initramfs on RZ/Five SMARC EVK: > > - AX45MP CPU > > - CPG > > - PINCTRL > > - PLIC > > - SCIF0 > > - SYSC > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > --- > > arch/riscv/boot/dts/Makefile | 1 + > > arch/riscv/boot/dts/renesas/r9a07g043.dtsi | 121 +++++++++++++++++++++ > > 2 files changed, 122 insertions(+) > > create mode 100644 arch/riscv/boot/dts/renesas/r9a07g043.dtsi > > > > diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile > > index ff174996cdfd..b0ff5fbabb0c 100644 > > --- a/arch/riscv/boot/dts/Makefile > > +++ b/arch/riscv/boot/dts/Makefile > > @@ -3,5 +3,6 @@ subdir-y += sifive > > subdir-y += starfive > > subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan > > subdir-y += microchip > > +subdir-y += renesas > > What are you building there? There is no DTS. > My plan was to get the initial minimal SoC DTSi and then gradually add the board DTS, but it looks like I'll have to include it along with this series. Cheers, Prabhakar
diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile index ff174996cdfd..b0ff5fbabb0c 100644 --- a/arch/riscv/boot/dts/Makefile +++ b/arch/riscv/boot/dts/Makefile @@ -3,5 +3,6 @@ subdir-y += sifive subdir-y += starfive subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan subdir-y += microchip +subdir-y += renesas obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y)) diff --git a/arch/riscv/boot/dts/renesas/r9a07g043.dtsi b/arch/riscv/boot/dts/renesas/r9a07g043.dtsi new file mode 100644 index 000000000000..6e0b640c6c7f --- /dev/null +++ b/arch/riscv/boot/dts/renesas/r9a07g043.dtsi @@ -0,0 +1,121 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +/* + * Device Tree Source for the RZ/Five SoC + * + * Copyright (C) 2022 Renesas Electronics Corp. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/r9a07g043-cpg.h> + +/ { + compatible = "renesas,r9a07g043"; + #address-cells = <2>; + #size-cells = <2>; + + /* clock can be either from exclk or crystal oscillator (XIN/XOUT) */ + extal_clk: extal-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + /* This value must be overridden by the board */ + clock-frequency = <0>; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <24000000>; + + ax45mp: cpu@0 { + compatible = "andestech,ax45mp", "riscv"; + device_type = "cpu"; + reg = <0x0>; + status = "okay"; + riscv,isa = "rv64imafdc"; + mmu-type = "riscv,sv39"; + i-cache-size = <0x8000>; + i-cache-line-size = <0x40>; + d-cache-size = <0x8000>; + d-cache-line-size = <0x40>; + clocks = <&cpg CPG_CORE R9A07G043_AX45MP_CORE0_CLK>, + <&cpg CPG_CORE R9A07G043_AX45MP_ACLK>; + + cpu0_intc: interrupt-controller { + #interrupt-cells = <1>; + compatible = "riscv,cpu-intc"; + interrupt-controller; + }; + }; + }; + + soc: soc { + compatible = "simple-bus"; + interrupt-parent = <&plic>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + scif0: serial@1004b800 { + compatible = "renesas,scif-r9a07g043", + "renesas,scif-r9a07g044"; + reg = <0 0x1004b800 0 0x400>; + interrupts = <412 IRQ_TYPE_LEVEL_HIGH>, + <414 IRQ_TYPE_LEVEL_HIGH>, + <415 IRQ_TYPE_LEVEL_HIGH>, + <413 IRQ_TYPE_LEVEL_HIGH>, + <416 IRQ_TYPE_LEVEL_HIGH>, + <416 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "eri", "rxi", "txi", + "bri", "dri", "tei"; + clocks = <&cpg CPG_MOD R9A07G043_SCIF0_CLK_PCK>; + clock-names = "fck"; + power-domains = <&cpg>; + resets = <&cpg R9A07G043_SCIF0_RST_SYSTEM_N>; + status = "disabled"; + }; + + cpg: clock-controller@11010000 { + compatible = "renesas,r9a07g043-cpg"; + reg = <0 0x11010000 0 0x10000>; + clocks = <&extal_clk>; + clock-names = "extal"; + #clock-cells = <2>; + #reset-cells = <1>; + #power-domain-cells = <0>; + }; + + sysc: system-controller@11020000 { + compatible = "renesas,r9a07g043-sysc"; + reg = <0 0x11020000 0 0x10000>; + status = "disabled"; + }; + + pinctrl: pinctrl@11030000 { + compatible = "renesas,r9a07g043-pinctrl"; + reg = <0 0x11030000 0 0x10000>; + gpio-controller; + #gpio-cells = <2>; + #interrupt-cells = <2>; + interrupt-controller; + gpio-ranges = <&pinctrl 0 0 152>; + clocks = <&cpg CPG_MOD R9A07G043_GPIO_HCLK>; + power-domains = <&cpg>; + resets = <&cpg R9A07G043_GPIO_RSTN>, + <&cpg R9A07G043_GPIO_PORT_RESETN>, + <&cpg R9A07G043_GPIO_SPARE_RESETN>; + }; + + plic: interrupt-controller@12c00000 { + compatible = "renesas,r9a07g043-plic", "andestech,nceplic100"; + #interrupt-cells = <2>; + #address-cells = <0>; + riscv,ndev = <543>; + interrupt-controller; + reg = <0x0 0x12c00000 0 0x400000>; + clocks = <&cpg CPG_MOD R9A07G043_NCEPLIC_ACLK>; + power-domains = <&cpg>; + resets = <&cpg R9A07G043_NCEPLIC_ARESETN>; + interrupts-extended = <&cpu0_intc 11 &cpu0_intc 9>; + }; + }; +};
Add initial device tree for Renesas RZ/Five RISC-V CPU Core (AX45MP Single). Below is the list of IP blocks added in the initial SoC DTSI which can be used to boot via initramfs on RZ/Five SMARC EVK: - AX45MP CPU - CPG - PINCTRL - PLIC - SCIF0 - SYSC Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> --- arch/riscv/boot/dts/Makefile | 1 + arch/riscv/boot/dts/renesas/r9a07g043.dtsi | 121 +++++++++++++++++++++ 2 files changed, 122 insertions(+) create mode 100644 arch/riscv/boot/dts/renesas/r9a07g043.dtsi