| Message ID | 20220824035542.706433-5-nava.kishore.manne@amd.com (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | Add afi config drivers support | expand |
On 24/08/2022 06:55, Nava kishore Manne wrote: > Add zynqmp AXI FIFO interface(AFI) config driver. This is useful for the > configuration of the PS-PL interface on Zynq US+ MPSoC platform. > > Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com> > --- (...) > + > +static struct platform_driver zynqmp_afi_driver = { > + .probe = zynqmp_afi_probe, > + .remove = zynqmp_afi_remove, > + .driver = { > + .name = "zynqmp_afi", > + .of_match_table = of_match_ptr(zynqmp_afi_of_match), It should generate warnings... test compile your driver. Drop of_match_ptr() or use __maybe_unused Best regards, Krzysztof
On 2022-08-24 at 09:25:42 +0530, Nava kishore Manne wrote: > Add zynqmp AXI FIFO interface(AFI) config driver. This is useful for the > configuration of the PS-PL interface on Zynq US+ MPSoC platform. Please help illustrate how to use the device for FPGA reprogramming, why it should be implemented as an FPGA bridge. From the code I actually didn't see any operation that gates the fpga-region from other part of the machine. > > Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com> > --- > MAINTAINERS | 6 ++ > drivers/fpga/Kconfig | 13 +++ > drivers/fpga/Makefile | 1 + > drivers/fpga/zynqmp-afi.c | 211 ++++++++++++++++++++++++++++++++++++++ > 4 files changed, 231 insertions(+) > create mode 100644 drivers/fpga/zynqmp-afi.c > > diff --git a/MAINTAINERS b/MAINTAINERS > index 20ffac651214..957e753e6406 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -8032,6 +8032,12 @@ F: Documentation/fpga/ > F: drivers/fpga/ > F: include/linux/fpga/ > > +FPGA ZYNQMP PS-PL BRIDGE DRIVER > +M: Nava kishore Manne <nava.kishore.manne@amd.com> > +S: Supported > +F: Documentation/devicetree/bindings/fpga/xlnx,zynqmp-afi-fpga.yaml > +F: drivers/fpga/zynqmp-afi.c > + > INTEL MAX10 BMC SECURE UPDATES > M: Russ Weight <russell.h.weight@intel.com> > L: linux-fpga@vger.kernel.org > diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig > index 6c416955da53..c08794d30fb5 100644 > --- a/drivers/fpga/Kconfig > +++ b/drivers/fpga/Kconfig > @@ -130,6 +130,19 @@ config XILINX_PR_DECOUPLER > reconfiguration, preventing the system deadlock that can > occur if AXI transactions are interrupted by DFX. > > +config ZYNQMP_AFI > + tristate "Xilinx ZYNQMP AFI support" > + depends on FPGA_BRIDGE > + help > + Say Y to enable drivers to handle the PS-PL clocks configurations > + and PS-PL Bus-width. Xilinx Zynq US+ MPSoC connect the PS to the > + programmable logic (PL) through the AXI port. This AXI port helps > + to establish the data path between the PS and PL. > + In-order to establish the proper communication path between PS and PL, > + the AXI port data path should be configured with the proper Bus-width > + values and it will also handles the PS-PL reset signals to reset the > + PL domain. Same concern, please describe its relationship to FPGA reprogramming. > + > config FPGA_REGION > tristate "FPGA Region" > depends on FPGA_BRIDGE > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile > index 42ae8b58abce..94cfe60972db 100644 > --- a/drivers/fpga/Makefile > +++ b/drivers/fpga/Makefile > @@ -31,6 +31,7 @@ obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o > obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera-fpga2sdram.o > obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o > obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o > +obj-$(CONFIG_ZYNQMP_AFI) += zynqmp-afi.o > > # High Level Interfaces > obj-$(CONFIG_FPGA_REGION) += fpga-region.o > diff --git a/drivers/fpga/zynqmp-afi.c b/drivers/fpga/zynqmp-afi.c > new file mode 100644 > index 000000000000..bc975d304039 > --- /dev/null > +++ b/drivers/fpga/zynqmp-afi.c > @@ -0,0 +1,211 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Copyright (C) 2022 Xilinx, Inc. > + */ > + > +#include <linux/err.h> > +#include <linux/firmware/xlnx-zynqmp.h> > +#include <linux/fpga/fpga-bridge.h> > +#include <linux/io.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/reset.h> > +#include <linux/slab.h> > + > +/* Registers and special values for doing register-based operations */ > +#define AFI_RDCHAN_CTRL_OFFSET 0x00 > +#define AFI_WRCHAN_CTRL_OFFSET 0x14 > +#define AFI_BUSWIDTH_MASK BIT(0) > + > +/** > + * struct zynqmp_afi - AFI register description. > + * @dev: device that owns this. > + * @of_node: Device Tree overlay. > + * @resets: Pointer to the reset control for ps-pl resets. > + */ > +struct zynqmp_afi { > + struct device *dev; > + struct device_node *of_node; > + struct reset_control *resets; > +}; > + > +/** > + * struct zynqmp_afi_configreg - AFI configuration registers info. > + * @reg: Name of the AFI configuration register. > + * @id: Register index value. > + */ > +struct zynqmp_afi_configreg { > + char *reg; > + u32 id; > +}; > + > +static struct zynqmp_afi_configreg afi_cfgreg[] = { > + {.reg = "xlnx,afi-fm0-rd-bus-width", .id = AFIFM0_RDCTRL}, > + {.reg = "xlnx,afi-fm1-rd-bus-width", .id = AFIFM1_RDCTRL}, > + {.reg = "xlnx,afi-fm2-rd-bus-width", .id = AFIFM2_RDCTRL}, > + {.reg = "xlnx,afi-fm3-rd-bus-width", .id = AFIFM3_RDCTRL}, > + {.reg = "xlnx,afi-fm4-rd-bus-width", .id = AFIFM4_RDCTRL}, > + {.reg = "xlnx,afi-fm5-rd-bus-width", .id = AFIFM5_RDCTRL}, > + {.reg = "xlnx,afi-fm6-rd-bus-width", .id = AFIFM6_RDCTRL}, > + {.reg = "xlnx,afi-fm0-wr-bus-width", .id = AFIFM0_WRCTRL}, > + {.reg = "xlnx,afi-fm1-wr-bus-width", .id = AFIFM1_WRCTRL}, > + {.reg = "xlnx,afi-fm2-wr-bus-width", .id = AFIFM2_WRCTRL}, > + {.reg = "xlnx,afi-fm3-wr-bus-width", .id = AFIFM3_WRCTRL}, > + {.reg = "xlnx,afi-fm4-wr-bus-width", .id = AFIFM4_WRCTRL}, > + {.reg = "xlnx,afi-fm5-wr-bus-width", .id = AFIFM5_WRCTRL}, > + {.reg = "xlnx,afi-fm6-wr-bus-width", .id = AFIFM6_WRCTRL}, > + {.reg = "xlnx,afi-fs-ss0-bus-width", .id = AFIFS}, > + {.reg = "xlnx,afi-fs-ss2-bus-width", .id = AFIFS_SS2}, > + {} > +}; > + > +static int zynqmp_afi_config(struct zynqmp_afi *afi_data) > +{ > + struct zynqmp_afi_configreg *cfgptr = afi_cfgreg; > + struct device_node *np = afi_data->of_node; > + u32 afi_ss0_val, afi_ss1_val, bus_width; > + int ret; > + > + while (cfgptr->reg) { > + ret = of_property_read_u32(np, cfgptr->reg, &bus_width); > + if (!ret) { > + if (cfgptr->id == AFIFS_SS2) { > + if (bus_width == 32) > + ret = zynqmp_pm_afi(AFIFS_SS2, > + AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL); > + else if (bus_width == 64) > + ret = zynqmp_pm_afi(AFIFS_SS2, > + AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL); > + else if (bus_width == 128) > + ret = zynqmp_pm_afi(AFIFS_SS2, > + AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL); > + else > + return -EINVAL; > + } else if (cfgptr->id == AFIFS) { > + if (bus_width == 32) > + afi_ss0_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; > + else if (bus_width == 64) > + afi_ss0_val = AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL; > + else if (bus_width == 128) > + afi_ss0_val = AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL; > + else > + return -EINVAL; > + > + ret = of_property_read_u32(np, "xlnx,afi-fs-ss1-bus-width", > + &bus_width); > + if (!ret) { > + if (bus_width == 32) > + afi_ss1_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; > + else if (bus_width == 64) > + afi_ss1_val = AFIFS_SS1_BUS_WIDTH_64_CONFIG_VAL; > + else if (bus_width == 128) > + afi_ss1_val = AFIFS_SS1_BUS_WIDTH_128_CONFIG_VAL; > + else > + return -EINVAL; > + > + ret = zynqmp_pm_afi(AFIFS, afi_ss1_val | afi_ss0_val); > + } > + } else { > + if (bus_width == 32) > + ret = zynqmp_pm_afi(cfgptr->id, > + AFIFM_BUS_WIDTH_32_CONFIG_VAL); > + else if (bus_width == 64) > + ret = zynqmp_pm_afi(cfgptr->id, > + AFIFM_BUS_WIDTH_64_CONFIG_VAL); > + else if (bus_width == 128) > + ret = zynqmp_pm_afi(cfgptr->id, > + AFIFM_BUS_WIDTH_128_CONFIG_VAL); > + else > + return -EINVAL; > + } > + } > + cfgptr++; > + } > + > + return 0; > +} > + > +static int zynqmp_afi_enable_set(struct fpga_bridge *bridge, bool enable) > +{ > + struct device_node *overlay = bridge->info->overlay; > + struct zynqmp_afi *priv = bridge->priv; > + int ret = 0; > + > + if (enable) { > + reset_control_reset(priv->resets); > + return 0; > + } > + > + of_node_get(overlay); > + priv->of_node = > + of_find_node_with_property(overlay, > + "xlnx,afi-fm0-rd-bus-width"); I'm a little confused here. The fpga_image_info.overlay is for fpga-region, but from your binding doc this property is for this afi device. You want to add another overlay targeting afi dev node during reprograming? > + if (priv->of_node) > + ret = zynqmp_afi_config(priv); > + of_node_put(priv->of_node); > + > + return ret; > +} > + > +static const struct fpga_bridge_ops zynqmp_afi_br_ops = { > + .enable_set = zynqmp_afi_enable_set, > +}; > + > +static const struct of_device_id zynqmp_afi_of_match[] = { > + { .compatible = "xlnx,zynqmp-afi-fpga" }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, zynqmp_afi_of_match); > + > +static int zynqmp_afi_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct zynqmp_afi *priv; > + struct fpga_bridge *br; > + > + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); > + if (!priv) > + return -ENOMEM; > + > + priv->dev = dev; > + > + priv->resets = devm_reset_control_array_get_optional_exclusive(&pdev->dev); > + if (IS_ERR(priv->resets)) > + return PTR_ERR(priv->resets); > + > + br = fpga_bridge_register(dev, "Xilinx ZynqMP AFI", > + &zynqmp_afi_br_ops, priv); > + if (IS_ERR(br)) { > + dev_err(dev, "unable to register Xilinx ZynqMP AFI"); Need a "\n" at the end? Thanks, Yilun > + return PTR_ERR(br); > + } > + > + platform_set_drvdata(pdev, br); > + > + return 0; > +} > + > +static int zynqmp_afi_remove(struct platform_device *pdev) > +{ > + struct fpga_bridge *bridge = platform_get_drvdata(pdev); > + > + fpga_bridge_unregister(bridge); > + > + return 0; > +} > + > +static struct platform_driver zynqmp_afi_driver = { > + .probe = zynqmp_afi_probe, > + .remove = zynqmp_afi_remove, > + .driver = { > + .name = "zynqmp_afi", > + .of_match_table = of_match_ptr(zynqmp_afi_of_match), > + }, > +}; > + > +module_platform_driver(zynqmp_afi_driver); > + > +MODULE_DESCRIPTION("ZYNQMP FPGA AXI FIFO interface configuration module"); > +MODULE_AUTHOR("Nava kishore Manne <nava.kishore.manne@amd.com>"); > +MODULE_LICENSE("GPL"); > -- > 2.25.1 >
Hi Yilun, Please find my response inline. > -----Original Message----- > From: Xu Yilun <yilun.xu@intel.com> > Sent: Saturday, August 27, 2022 5:56 PM > To: Manne, Nava kishore <nava.kishore.manne@amd.com> > Cc: git (AMD-Xilinx) <git@amd.com>; robh+dt@kernel.org; > krzysztof.kozlowski+dt@linaro.org; michal.simek@xilinx.com; > mdf@kernel.org; hao.wu@intel.com; trix@redhat.com; > p.zabel@pengutronix.de; gregkh@linuxfoundation.org; > ronak.jain@xilinx.com; rajan.vaja@xilinx.com; > abhyuday.godhasara@xilinx.com; piyush.mehta@xilinx.com; > lakshmi.sai.krishna.potthuri@xilinx.com; harsha.harsha@xilinx.com; > linus.walleij@linaro.org; nava.manne@xilinx.com; > devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- > kernel@vger.kernel.org; linux-fpga@vger.kernel.org > Subject: Re: [PATCH 4/4] fpga: zynqmp: Add afi config driver > > CAUTION: This message has originated from an External Source. Please use > proper judgment and caution when opening attachments, clicking links, or > responding to this email. > > > On 2022-08-24 at 09:25:42 +0530, Nava kishore Manne wrote: > > Add zynqmp AXI FIFO interface(AFI) config driver. This is useful for > > the configuration of the PS-PL interface on Zynq US+ MPSoC platform. > > Please help illustrate how to use the device for FPGA reprogramming, why it > should be implemented as an FPGA bridge. > > From the code I actually didn't see any operation that gates the fpga-region > from other part of the machine. > The Zynq UltraScale MPSoC family consists of a system-on-chip (SoC) style integrated processing system (PS) and a Programmable Logic (PL) unit, providing an extensible and flexible SoC solution on a single die. Xilinx Zynq US+ MPSoC connect the PS to the programmable logic (PL) through the AXI port. This AXI port helps to establish the data path between the PS and PL (Here AXI Interface act as a Gating between PS and PL) and this AXI port configuration vary from design to design. In-order to establish the proper communication path between PS and PL (Full region), the AXI port data path should be configured with proper values priories to load the full region. Will update the description in v2. > > > > Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com> > > --- > > MAINTAINERS | 6 ++ > > drivers/fpga/Kconfig | 13 +++ > > drivers/fpga/Makefile | 1 + > > drivers/fpga/zynqmp-afi.c | 211 > > ++++++++++++++++++++++++++++++++++++++ > > 4 files changed, 231 insertions(+) > > create mode 100644 drivers/fpga/zynqmp-afi.c > > > > diff --git a/MAINTAINERS b/MAINTAINERS index > > 20ffac651214..957e753e6406 100644 > > --- a/MAINTAINERS > > +++ b/MAINTAINERS > > @@ -8032,6 +8032,12 @@ F: Documentation/fpga/ > > F: drivers/fpga/ > > F: include/linux/fpga/ > > > > +FPGA ZYNQMP PS-PL BRIDGE DRIVER > > +M: Nava kishore Manne <nava.kishore.manne@amd.com> > > +S: Supported > > +F: Documentation/devicetree/bindings/fpga/xlnx,zynqmp-afi-fpga.yaml > > +F: drivers/fpga/zynqmp-afi.c > > + > > INTEL MAX10 BMC SECURE UPDATES > > M: Russ Weight <russell.h.weight@intel.com> > > L: linux-fpga@vger.kernel.org > > diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index > > 6c416955da53..c08794d30fb5 100644 > > --- a/drivers/fpga/Kconfig > > +++ b/drivers/fpga/Kconfig > > @@ -130,6 +130,19 @@ config XILINX_PR_DECOUPLER > > reconfiguration, preventing the system deadlock that can > > occur if AXI transactions are interrupted by DFX. > > > > +config ZYNQMP_AFI > > + tristate "Xilinx ZYNQMP AFI support" > > + depends on FPGA_BRIDGE > > + help > > + Say Y to enable drivers to handle the PS-PL clocks configurations > > + and PS-PL Bus-width. Xilinx Zynq US+ MPSoC connect the PS to the > > + programmable logic (PL) through the AXI port. This AXI port helps > > + to establish the data path between the PS and PL. > > + In-order to establish the proper communication path between PS and > PL, > > + the AXI port data path should be configured with the proper Bus- > width > > + values and it will also handles the PS-PL reset signals to reset the > > + PL domain. > > Same concern, please describe its relationship to FPGA reprogramming. > Same as above. Will update the description in v2. > > + > > config FPGA_REGION > > tristate "FPGA Region" > > depends on FPGA_BRIDGE > > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index > > 42ae8b58abce..94cfe60972db 100644 > > --- a/drivers/fpga/Makefile > > +++ b/drivers/fpga/Makefile > > @@ -31,6 +31,7 @@ obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o > > obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera- > fpga2sdram.o > > obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o > > obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o > > +obj-$(CONFIG_ZYNQMP_AFI) += zynqmp-afi.o > > > > # High Level Interfaces > > obj-$(CONFIG_FPGA_REGION) += fpga-region.o > > diff --git a/drivers/fpga/zynqmp-afi.c b/drivers/fpga/zynqmp-afi.c new > > file mode 100644 index 000000000000..bc975d304039 > > --- /dev/null > > +++ b/drivers/fpga/zynqmp-afi.c > > @@ -0,0 +1,211 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* > > + * Copyright (C) 2022 Xilinx, Inc. > > + */ > > + > > +#include <linux/err.h> > > +#include <linux/firmware/xlnx-zynqmp.h> #include > > +<linux/fpga/fpga-bridge.h> #include <linux/io.h> #include > > +<linux/module.h> #include <linux/of.h> #include > > +<linux/platform_device.h> #include <linux/reset.h> #include > > +<linux/slab.h> > > + > > +/* Registers and special values for doing register-based operations */ > > +#define AFI_RDCHAN_CTRL_OFFSET 0x00 > > +#define AFI_WRCHAN_CTRL_OFFSET 0x14 > > +#define AFI_BUSWIDTH_MASK BIT(0) > > + > > +/** > > + * struct zynqmp_afi - AFI register description. > > + * @dev: device that owns this. > > + * @of_node: Device Tree overlay. > > + * @resets: Pointer to the reset control for ps-pl resets. > > + */ > > +struct zynqmp_afi { > > + struct device *dev; > > + struct device_node *of_node; > > + struct reset_control *resets; > > +}; > > + > > +/** > > + * struct zynqmp_afi_configreg - AFI configuration registers info. > > + * @reg: Name of the AFI configuration register. > > + * @id: Register index value. > > + */ > > +struct zynqmp_afi_configreg { > > + char *reg; > > + u32 id; > > +}; > > + > > +static struct zynqmp_afi_configreg afi_cfgreg[] = { > > + {.reg = "xlnx,afi-fm0-rd-bus-width", .id = AFIFM0_RDCTRL}, > > + {.reg = "xlnx,afi-fm1-rd-bus-width", .id = AFIFM1_RDCTRL}, > > + {.reg = "xlnx,afi-fm2-rd-bus-width", .id = AFIFM2_RDCTRL}, > > + {.reg = "xlnx,afi-fm3-rd-bus-width", .id = AFIFM3_RDCTRL}, > > + {.reg = "xlnx,afi-fm4-rd-bus-width", .id = AFIFM4_RDCTRL}, > > + {.reg = "xlnx,afi-fm5-rd-bus-width", .id = AFIFM5_RDCTRL}, > > + {.reg = "xlnx,afi-fm6-rd-bus-width", .id = AFIFM6_RDCTRL}, > > + {.reg = "xlnx,afi-fm0-wr-bus-width", .id = AFIFM0_WRCTRL}, > > + {.reg = "xlnx,afi-fm1-wr-bus-width", .id = AFIFM1_WRCTRL}, > > + {.reg = "xlnx,afi-fm2-wr-bus-width", .id = AFIFM2_WRCTRL}, > > + {.reg = "xlnx,afi-fm3-wr-bus-width", .id = AFIFM3_WRCTRL}, > > + {.reg = "xlnx,afi-fm4-wr-bus-width", .id = AFIFM4_WRCTRL}, > > + {.reg = "xlnx,afi-fm5-wr-bus-width", .id = AFIFM5_WRCTRL}, > > + {.reg = "xlnx,afi-fm6-wr-bus-width", .id = AFIFM6_WRCTRL}, > > + {.reg = "xlnx,afi-fs-ss0-bus-width", .id = AFIFS}, > > + {.reg = "xlnx,afi-fs-ss2-bus-width", .id = AFIFS_SS2}, > > + {} > > +}; > > + > > +static int zynqmp_afi_config(struct zynqmp_afi *afi_data) { > > + struct zynqmp_afi_configreg *cfgptr = afi_cfgreg; > > + struct device_node *np = afi_data->of_node; > > + u32 afi_ss0_val, afi_ss1_val, bus_width; > > + int ret; > > + > > + while (cfgptr->reg) { > > + ret = of_property_read_u32(np, cfgptr->reg, &bus_width); > > + if (!ret) { > > + if (cfgptr->id == AFIFS_SS2) { > > + if (bus_width == 32) > > + ret = zynqmp_pm_afi(AFIFS_SS2, > > + AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL); > > + else if (bus_width == 64) > > + ret = zynqmp_pm_afi(AFIFS_SS2, > > + > AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL); > > + else if (bus_width == 128) > > + ret = zynqmp_pm_afi(AFIFS_SS2, > > + > AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL); > > + else > > + return -EINVAL; > > + } else if (cfgptr->id == AFIFS) { > > + if (bus_width == 32) > > + afi_ss0_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; > > + else if (bus_width == 64) > > + afi_ss0_val = > AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL; > > + else if (bus_width == 128) > > + afi_ss0_val = > AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL; > > + else > > + return -EINVAL; > > + > > + ret = of_property_read_u32(np, "xlnx,afi-fs-ss1-bus- > width", > > + &bus_width); > > + if (!ret) { > > + if (bus_width == 32) > > + afi_ss1_val = > AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; > > + else if (bus_width == 64) > > + afi_ss1_val = > AFIFS_SS1_BUS_WIDTH_64_CONFIG_VAL; > > + else if (bus_width == 128) > > + afi_ss1_val = > AFIFS_SS1_BUS_WIDTH_128_CONFIG_VAL; > > + else > > + return -EINVAL; > > + > > + ret = zynqmp_pm_afi(AFIFS, afi_ss1_val | > afi_ss0_val); > > + } > > + } else { > > + if (bus_width == 32) > > + ret = zynqmp_pm_afi(cfgptr->id, > > + AFIFM_BUS_WIDTH_32_CONFIG_VAL); > > + else if (bus_width == 64) > > + ret = zynqmp_pm_afi(cfgptr->id, > > + AFIFM_BUS_WIDTH_64_CONFIG_VAL); > > + else if (bus_width == 128) > > + ret = zynqmp_pm_afi(cfgptr->id, > > + AFIFM_BUS_WIDTH_128_CONFIG_VAL); > > + else > > + return -EINVAL; > > + } > > + } > > + cfgptr++; > > + } > > + > > + return 0; > > +} > > + > > +static int zynqmp_afi_enable_set(struct fpga_bridge *bridge, bool > > +enable) { > > + struct device_node *overlay = bridge->info->overlay; > > + struct zynqmp_afi *priv = bridge->priv; > > + int ret = 0; > > + > > + if (enable) { > > + reset_control_reset(priv->resets); > > + return 0; > > + } > > + > > + of_node_get(overlay); > > + priv->of_node = > > + of_find_node_with_property(overlay, > > + "xlnx,afi-fm0-rd-bus-width"); > > I'm a little confused here. The fpga_image_info.overlay is for fpga-region, but > from your binding doc this property is for this afi device. You want to add > another overlay targeting afi dev node during reprograming? > Yes, it uses Overlay's(overlay targeting afi dev node). As I said above for design-to-design AFI configs relevant to the full region may change and these configs must be set prior to program the full region once this overlay integrated to the live tree the existing afi config values will be replace with the new one's > > + if (priv->of_node) > > + ret = zynqmp_afi_config(priv); > > + of_node_put(priv->of_node); > > + > > + return ret; > > +} > > + > > +static const struct fpga_bridge_ops zynqmp_afi_br_ops = { > > + .enable_set = zynqmp_afi_enable_set, }; > > + > > +static const struct of_device_id zynqmp_afi_of_match[] = { > > + { .compatible = "xlnx,zynqmp-afi-fpga" }, > > + { }, > > +}; > > +MODULE_DEVICE_TABLE(of, zynqmp_afi_of_match); > > + > > +static int zynqmp_afi_probe(struct platform_device *pdev) { > > + struct device *dev = &pdev->dev; > > + struct zynqmp_afi *priv; > > + struct fpga_bridge *br; > > + > > + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); > > + if (!priv) > > + return -ENOMEM; > > + > > + priv->dev = dev; > > + > > + priv->resets = > devm_reset_control_array_get_optional_exclusive(&pdev->dev); > > + if (IS_ERR(priv->resets)) > > + return PTR_ERR(priv->resets); > > + > > + br = fpga_bridge_register(dev, "Xilinx ZynqMP AFI", > > + &zynqmp_afi_br_ops, priv); > > + if (IS_ERR(br)) { > > + dev_err(dev, "unable to register Xilinx ZynqMP AFI"); > > Need a "\n" at the end? > Will fix. Regards, Navakishore.
Hi Nava, On 2022-08-30 11:19, Manne, Nava kishore wrote: > Hi Yilun, > > Please find my response inline. > >> -----Original Message----- >> From: Xu Yilun <yilun.xu@intel.com> >> Sent: Saturday, August 27, 2022 5:56 PM >> To: Manne, Nava kishore <nava.kishore.manne@amd.com> >> Cc: git (AMD-Xilinx) <git@amd.com>; robh+dt@kernel.org; >> krzysztof.kozlowski+dt@linaro.org; michal.simek@xilinx.com; >> mdf@kernel.org; hao.wu@intel.com; trix@redhat.com; >> p.zabel@pengutronix.de; gregkh@linuxfoundation.org; >> ronak.jain@xilinx.com; rajan.vaja@xilinx.com; >> abhyuday.godhasara@xilinx.com; piyush.mehta@xilinx.com; >> lakshmi.sai.krishna.potthuri@xilinx.com; harsha.harsha@xilinx.com; >> linus.walleij@linaro.org; nava.manne@xilinx.com; >> devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- >> kernel@vger.kernel.org; linux-fpga@vger.kernel.org >> Subject: Re: [PATCH 4/4] fpga: zynqmp: Add afi config driver >> >> CAUTION: This message has originated from an External Source. Please use >> proper judgment and caution when opening attachments, clicking links, or >> responding to this email. >> >> >> On 2022-08-24 at 09:25:42 +0530, Nava kishore Manne wrote: >>> Add zynqmp AXI FIFO interface(AFI) config driver. This is useful for >>> the configuration of the PS-PL interface on Zynq US+ MPSoC platform. >> >> Please help illustrate how to use the device for FPGA reprogramming, why it >> should be implemented as an FPGA bridge. >> >> From the code I actually didn't see any operation that gates the fpga-region >> from other part of the machine. >> > > The Zynq UltraScale MPSoC family consists of a system-on-chip (SoC) style integrated processing system (PS) > and a Programmable Logic (PL) unit, providing an extensible and flexible SoC solution on a single die. > Xilinx Zynq US+ MPSoC connect the PS to the programmable logic (PL) through the AXI port. > This AXI port helps to establish the data path between the PS and PL (Here AXI Interface act as a Gating between PS and PL) > and this AXI port configuration vary from design to design. In-order to establish the proper communication path between > PS and PL (Full region), the AXI port data path should be configured with proper values priories to load the full region. > > Will update the description in v2. Are you implementing your AFI driver as a Bridge because you want to change the configuration of the AXI HP interfaces exported by the PS every time you reconfigure the full fabric? I understand the need to change the configuration of the PS-PL interface at each full reconfiguration to ensure that the parameters of the AXI ports exported by the PS (like the widths of data read and write channels) matches the configuration of the master AXI ports exported by the PL design. However, it seems to me that performing this configuration doesn't fit the role of the FPGA Bridge, whose sole responsibility should be gating the Region's interface during reconfiguration. I think this need could be addressed by adding a new component to the FPGA subsystem called "FPGA Adapter". The Adapter will be an optional component associated with a Region like a Bridge. It will be responsible for changing the configuration of its Region's static interface (or PS/HPS/DRAM interface for the full FPGA) to match the interface exported by the specific reconfigurable module (or full static design). Moreover, besides bus-level properties like address/data width and protocol conversion, the Adapter could also be used to configure system-level properties. For instance, the designer may use it to change the memory access policy for the specific reconfigurable module if it uses bus mastering. > >>> >>> Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com> >>> --- >>> MAINTAINERS | 6 ++ >>> drivers/fpga/Kconfig | 13 +++ >>> drivers/fpga/Makefile | 1 + >>> drivers/fpga/zynqmp-afi.c | 211 >>> ++++++++++++++++++++++++++++++++++++++ >>> 4 files changed, 231 insertions(+) >>> create mode 100644 drivers/fpga/zynqmp-afi.c >>> >>> diff --git a/MAINTAINERS b/MAINTAINERS index >>> 20ffac651214..957e753e6406 100644 >>> --- a/MAINTAINERS >>> +++ b/MAINTAINERS >>> @@ -8032,6 +8032,12 @@ F: Documentation/fpga/ >>> F: drivers/fpga/ >>> F: include/linux/fpga/ >>> >>> +FPGA ZYNQMP PS-PL BRIDGE DRIVER >>> +M: Nava kishore Manne <nava.kishore.manne@amd.com> >>> +S: Supported >>> +F: Documentation/devicetree/bindings/fpga/xlnx,zynqmp-afi-fpga.yaml >>> +F: drivers/fpga/zynqmp-afi.c >>> + >>> INTEL MAX10 BMC SECURE UPDATES >>> M: Russ Weight <russell.h.weight@intel.com> >>> L: linux-fpga@vger.kernel.org >>> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index >>> 6c416955da53..c08794d30fb5 100644 >>> --- a/drivers/fpga/Kconfig >>> +++ b/drivers/fpga/Kconfig >>> @@ -130,6 +130,19 @@ config XILINX_PR_DECOUPLER >>> reconfiguration, preventing the system deadlock that can >>> occur if AXI transactions are interrupted by DFX. >>> >>> +config ZYNQMP_AFI >>> + tristate "Xilinx ZYNQMP AFI support" >>> + depends on FPGA_BRIDGE >>> + help >>> + Say Y to enable drivers to handle the PS-PL clocks configurations >>> + and PS-PL Bus-width. Xilinx Zynq US+ MPSoC connect the PS to the >>> + programmable logic (PL) through the AXI port. This AXI port helps >>> + to establish the data path between the PS and PL. >>> + In-order to establish the proper communication path between PS and >> PL, >>> + the AXI port data path should be configured with the proper Bus- >> width >>> + values and it will also handles the PS-PL reset signals to reset the >>> + PL domain. >> >> Same concern, please describe its relationship to FPGA reprogramming. >> > > Same as above. > Will update the description in v2. > >>> + >>> config FPGA_REGION >>> tristate "FPGA Region" >>> depends on FPGA_BRIDGE >>> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index >>> 42ae8b58abce..94cfe60972db 100644 >>> --- a/drivers/fpga/Makefile >>> +++ b/drivers/fpga/Makefile >>> @@ -31,6 +31,7 @@ obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o >>> obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera- >> fpga2sdram.o >>> obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o >>> obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o >>> +obj-$(CONFIG_ZYNQMP_AFI) += zynqmp-afi.o >>> >>> # High Level Interfaces >>> obj-$(CONFIG_FPGA_REGION) += fpga-region.o >>> diff --git a/drivers/fpga/zynqmp-afi.c b/drivers/fpga/zynqmp-afi.c new >>> file mode 100644 index 000000000000..bc975d304039 >>> --- /dev/null >>> +++ b/drivers/fpga/zynqmp-afi.c >>> @@ -0,0 +1,211 @@ >>> +// SPDX-License-Identifier: GPL-2.0 >>> +/* >>> + * Copyright (C) 2022 Xilinx, Inc. >>> + */ >>> + >>> +#include <linux/err.h> >>> +#include <linux/firmware/xlnx-zynqmp.h> #include >>> +<linux/fpga/fpga-bridge.h> #include <linux/io.h> #include >>> +<linux/module.h> #include <linux/of.h> #include >>> +<linux/platform_device.h> #include <linux/reset.h> #include >>> +<linux/slab.h> >>> + >>> +/* Registers and special values for doing register-based operations */ >>> +#define AFI_RDCHAN_CTRL_OFFSET 0x00 >>> +#define AFI_WRCHAN_CTRL_OFFSET 0x14 >>> +#define AFI_BUSWIDTH_MASK BIT(0) >>> + >>> +/** >>> + * struct zynqmp_afi - AFI register description. >>> + * @dev: device that owns this. >>> + * @of_node: Device Tree overlay. >>> + * @resets: Pointer to the reset control for ps-pl resets. >>> + */ >>> +struct zynqmp_afi { >>> + struct device *dev; >>> + struct device_node *of_node; >>> + struct reset_control *resets; >>> +}; >>> + >>> +/** >>> + * struct zynqmp_afi_configreg - AFI configuration registers info. >>> + * @reg: Name of the AFI configuration register. >>> + * @id: Register index value. >>> + */ >>> +struct zynqmp_afi_configreg { >>> + char *reg; >>> + u32 id; >>> +}; >>> + >>> +static struct zynqmp_afi_configreg afi_cfgreg[] = { >>> + {.reg = "xlnx,afi-fm0-rd-bus-width", .id = AFIFM0_RDCTRL}, >>> + {.reg = "xlnx,afi-fm1-rd-bus-width", .id = AFIFM1_RDCTRL}, >>> + {.reg = "xlnx,afi-fm2-rd-bus-width", .id = AFIFM2_RDCTRL}, >>> + {.reg = "xlnx,afi-fm3-rd-bus-width", .id = AFIFM3_RDCTRL}, >>> + {.reg = "xlnx,afi-fm4-rd-bus-width", .id = AFIFM4_RDCTRL}, >>> + {.reg = "xlnx,afi-fm5-rd-bus-width", .id = AFIFM5_RDCTRL}, >>> + {.reg = "xlnx,afi-fm6-rd-bus-width", .id = AFIFM6_RDCTRL}, >>> + {.reg = "xlnx,afi-fm0-wr-bus-width", .id = AFIFM0_WRCTRL}, >>> + {.reg = "xlnx,afi-fm1-wr-bus-width", .id = AFIFM1_WRCTRL}, >>> + {.reg = "xlnx,afi-fm2-wr-bus-width", .id = AFIFM2_WRCTRL}, >>> + {.reg = "xlnx,afi-fm3-wr-bus-width", .id = AFIFM3_WRCTRL}, >>> + {.reg = "xlnx,afi-fm4-wr-bus-width", .id = AFIFM4_WRCTRL}, >>> + {.reg = "xlnx,afi-fm5-wr-bus-width", .id = AFIFM5_WRCTRL}, >>> + {.reg = "xlnx,afi-fm6-wr-bus-width", .id = AFIFM6_WRCTRL}, >>> + {.reg = "xlnx,afi-fs-ss0-bus-width", .id = AFIFS}, >>> + {.reg = "xlnx,afi-fs-ss2-bus-width", .id = AFIFS_SS2}, >>> + {} >>> +}; >>> + >>> +static int zynqmp_afi_config(struct zynqmp_afi *afi_data) { >>> + struct zynqmp_afi_configreg *cfgptr = afi_cfgreg; >>> + struct device_node *np = afi_data->of_node; >>> + u32 afi_ss0_val, afi_ss1_val, bus_width; >>> + int ret; >>> + >>> + while (cfgptr->reg) { >>> + ret = of_property_read_u32(np, cfgptr->reg, &bus_width); >>> + if (!ret) { >>> + if (cfgptr->id == AFIFS_SS2) { >>> + if (bus_width == 32) >>> + ret = zynqmp_pm_afi(AFIFS_SS2, >>> + AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL); >>> + else if (bus_width == 64) >>> + ret = zynqmp_pm_afi(AFIFS_SS2, >>> + >> AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL); >>> + else if (bus_width == 128) >>> + ret = zynqmp_pm_afi(AFIFS_SS2, >>> + >> AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL); >>> + else >>> + return -EINVAL; >>> + } else if (cfgptr->id == AFIFS) { >>> + if (bus_width == 32) >>> + afi_ss0_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; >>> + else if (bus_width == 64) >>> + afi_ss0_val = >> AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL; >>> + else if (bus_width == 128) >>> + afi_ss0_val = >> AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL; >>> + else >>> + return -EINVAL; >>> + >>> + ret = of_property_read_u32(np, "xlnx,afi-fs-ss1-bus- >> width", >>> + &bus_width); >>> + if (!ret) { >>> + if (bus_width == 32) >>> + afi_ss1_val = >> AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; >>> + else if (bus_width == 64) >>> + afi_ss1_val = >> AFIFS_SS1_BUS_WIDTH_64_CONFIG_VAL; >>> + else if (bus_width == 128) >>> + afi_ss1_val = >> AFIFS_SS1_BUS_WIDTH_128_CONFIG_VAL; >>> + else >>> + return -EINVAL; >>> + >>> + ret = zynqmp_pm_afi(AFIFS, afi_ss1_val | >> afi_ss0_val); >>> + } >>> + } else { >>> + if (bus_width == 32) >>> + ret = zynqmp_pm_afi(cfgptr->id, >>> + AFIFM_BUS_WIDTH_32_CONFIG_VAL); >>> + else if (bus_width == 64) >>> + ret = zynqmp_pm_afi(cfgptr->id, >>> + AFIFM_BUS_WIDTH_64_CONFIG_VAL); >>> + else if (bus_width == 128) >>> + ret = zynqmp_pm_afi(cfgptr->id, >>> + AFIFM_BUS_WIDTH_128_CONFIG_VAL); >>> + else >>> + return -EINVAL; >>> + } >>> + } >>> + cfgptr++; >>> + } >>> + >>> + return 0; >>> +} >>> + >>> +static int zynqmp_afi_enable_set(struct fpga_bridge *bridge, bool >>> +enable) { >>> + struct device_node *overlay = bridge->info->overlay; >>> + struct zynqmp_afi *priv = bridge->priv; >>> + int ret = 0; >>> + >>> + if (enable) { >>> + reset_control_reset(priv->resets); >>> + return 0; >>> + } >>> + >>> + of_node_get(overlay); >>> + priv->of_node = >>> + of_find_node_with_property(overlay, >>> + "xlnx,afi-fm0-rd-bus-width"); >> >> I'm a little confused here. The fpga_image_info.overlay is for fpga-region, but >> from your binding doc this property is for this afi device. You want to add >> another overlay targeting afi dev node during reprograming? >> > > Yes, it uses Overlay's(overlay targeting afi dev node). As I said above for design-to-design AFI configs > relevant to the full region may change and these configs must be set prior to program the full region > once this overlay integrated to the live tree the existing afi config values will be replace with the new one's > >>> + if (priv->of_node) >>> + ret = zynqmp_afi_config(priv); >>> + of_node_put(priv->of_node); >>> + >>> + return ret; >>> +} >>> + >>> +static const struct fpga_bridge_ops zynqmp_afi_br_ops = { >>> + .enable_set = zynqmp_afi_enable_set, }; >>> + >>> +static const struct of_device_id zynqmp_afi_of_match[] = { >>> + { .compatible = "xlnx,zynqmp-afi-fpga" }, >>> + { }, >>> +}; >>> +MODULE_DEVICE_TABLE(of, zynqmp_afi_of_match); >>> + >>> +static int zynqmp_afi_probe(struct platform_device *pdev) { >>> + struct device *dev = &pdev->dev; >>> + struct zynqmp_afi *priv; >>> + struct fpga_bridge *br; >>> + >>> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); >>> + if (!priv) >>> + return -ENOMEM; >>> + >>> + priv->dev = dev; >>> + >>> + priv->resets = >> devm_reset_control_array_get_optional_exclusive(&pdev->dev); >>> + if (IS_ERR(priv->resets)) >>> + return PTR_ERR(priv->resets); >>> + >>> + br = fpga_bridge_register(dev, "Xilinx ZynqMP AFI", >>> + &zynqmp_afi_br_ops, priv); >>> + if (IS_ERR(br)) { >>> + dev_err(dev, "unable to register Xilinx ZynqMP AFI"); >> >> Need a "\n" at the end? >> > > Will fix. > > Regards, > Navakishore. > Thanks, Marco
On 2022-08-30 at 09:19:52 +0000, Manne, Nava kishore wrote: > Hi Yilun, > > Please find my response inline. > > > -----Original Message----- > > From: Xu Yilun <yilun.xu@intel.com> > > Sent: Saturday, August 27, 2022 5:56 PM > > To: Manne, Nava kishore <nava.kishore.manne@amd.com> > > Cc: git (AMD-Xilinx) <git@amd.com>; robh+dt@kernel.org; > > krzysztof.kozlowski+dt@linaro.org; michal.simek@xilinx.com; > > mdf@kernel.org; hao.wu@intel.com; trix@redhat.com; > > p.zabel@pengutronix.de; gregkh@linuxfoundation.org; > > ronak.jain@xilinx.com; rajan.vaja@xilinx.com; > > abhyuday.godhasara@xilinx.com; piyush.mehta@xilinx.com; > > lakshmi.sai.krishna.potthuri@xilinx.com; harsha.harsha@xilinx.com; > > linus.walleij@linaro.org; nava.manne@xilinx.com; > > devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- > > kernel@vger.kernel.org; linux-fpga@vger.kernel.org > > Subject: Re: [PATCH 4/4] fpga: zynqmp: Add afi config driver > > > > CAUTION: This message has originated from an External Source. Please use > > proper judgment and caution when opening attachments, clicking links, or > > responding to this email. > > > > > > On 2022-08-24 at 09:25:42 +0530, Nava kishore Manne wrote: > > > Add zynqmp AXI FIFO interface(AFI) config driver. This is useful for > > > the configuration of the PS-PL interface on Zynq US+ MPSoC platform. > > > > Please help illustrate how to use the device for FPGA reprogramming, why it > > should be implemented as an FPGA bridge. > > > > From the code I actually didn't see any operation that gates the fpga-region > > from other part of the machine. > > > > The Zynq UltraScale MPSoC family consists of a system-on-chip (SoC) style integrated processing system (PS) > and a Programmable Logic (PL) unit, providing an extensible and flexible SoC solution on a single die. > Xilinx Zynq US+ MPSoC connect the PS to the programmable logic (PL) through the AXI port. > This AXI port helps to establish the data path between the PS and PL (Here AXI Interface act as a Gating between PS and PL) > and this AXI port configuration vary from design to design. In-order to establish the proper communication path between > PS and PL (Full region), the AXI port data path should be configured with proper values priories to load the full region. > > Will update the description in v2. > > > > > > > Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com> > > > --- > > > MAINTAINERS | 6 ++ > > > drivers/fpga/Kconfig | 13 +++ > > > drivers/fpga/Makefile | 1 + > > > drivers/fpga/zynqmp-afi.c | 211 > > > ++++++++++++++++++++++++++++++++++++++ > > > 4 files changed, 231 insertions(+) > > > create mode 100644 drivers/fpga/zynqmp-afi.c > > > > > > diff --git a/MAINTAINERS b/MAINTAINERS index > > > 20ffac651214..957e753e6406 100644 > > > --- a/MAINTAINERS > > > +++ b/MAINTAINERS > > > @@ -8032,6 +8032,12 @@ F: Documentation/fpga/ > > > F: drivers/fpga/ > > > F: include/linux/fpga/ > > > > > > +FPGA ZYNQMP PS-PL BRIDGE DRIVER > > > +M: Nava kishore Manne <nava.kishore.manne@amd.com> > > > +S: Supported > > > +F: Documentation/devicetree/bindings/fpga/xlnx,zynqmp-afi-fpga.yaml > > > +F: drivers/fpga/zynqmp-afi.c > > > + > > > INTEL MAX10 BMC SECURE UPDATES > > > M: Russ Weight <russell.h.weight@intel.com> > > > L: linux-fpga@vger.kernel.org > > > diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index > > > 6c416955da53..c08794d30fb5 100644 > > > --- a/drivers/fpga/Kconfig > > > +++ b/drivers/fpga/Kconfig > > > @@ -130,6 +130,19 @@ config XILINX_PR_DECOUPLER > > > reconfiguration, preventing the system deadlock that can > > > occur if AXI transactions are interrupted by DFX. > > > > > > +config ZYNQMP_AFI > > > + tristate "Xilinx ZYNQMP AFI support" > > > + depends on FPGA_BRIDGE > > > + help > > > + Say Y to enable drivers to handle the PS-PL clocks configurations > > > + and PS-PL Bus-width. Xilinx Zynq US+ MPSoC connect the PS to the > > > + programmable logic (PL) through the AXI port. This AXI port helps > > > + to establish the data path between the PS and PL. > > > + In-order to establish the proper communication path between PS and > > PL, > > > + the AXI port data path should be configured with the proper Bus- > > width > > > + values and it will also handles the PS-PL reset signals to reset the > > > + PL domain. > > > > Same concern, please describe its relationship to FPGA reprogramming. > > > > Same as above. > Will update the description in v2. > > > > + > > > config FPGA_REGION > > > tristate "FPGA Region" > > > depends on FPGA_BRIDGE > > > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index > > > 42ae8b58abce..94cfe60972db 100644 > > > --- a/drivers/fpga/Makefile > > > +++ b/drivers/fpga/Makefile > > > @@ -31,6 +31,7 @@ obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o > > > obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera- > > fpga2sdram.o > > > obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o > > > obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o > > > +obj-$(CONFIG_ZYNQMP_AFI) += zynqmp-afi.o > > > > > > # High Level Interfaces > > > obj-$(CONFIG_FPGA_REGION) += fpga-region.o > > > diff --git a/drivers/fpga/zynqmp-afi.c b/drivers/fpga/zynqmp-afi.c new > > > file mode 100644 index 000000000000..bc975d304039 > > > --- /dev/null > > > +++ b/drivers/fpga/zynqmp-afi.c > > > @@ -0,0 +1,211 @@ > > > +// SPDX-License-Identifier: GPL-2.0 > > > +/* > > > + * Copyright (C) 2022 Xilinx, Inc. > > > + */ > > > + > > > +#include <linux/err.h> > > > +#include <linux/firmware/xlnx-zynqmp.h> #include > > > +<linux/fpga/fpga-bridge.h> #include <linux/io.h> #include > > > +<linux/module.h> #include <linux/of.h> #include > > > +<linux/platform_device.h> #include <linux/reset.h> #include > > > +<linux/slab.h> > > > + > > > +/* Registers and special values for doing register-based operations */ > > > +#define AFI_RDCHAN_CTRL_OFFSET 0x00 > > > +#define AFI_WRCHAN_CTRL_OFFSET 0x14 > > > +#define AFI_BUSWIDTH_MASK BIT(0) > > > + > > > +/** > > > + * struct zynqmp_afi - AFI register description. > > > + * @dev: device that owns this. > > > + * @of_node: Device Tree overlay. > > > + * @resets: Pointer to the reset control for ps-pl resets. > > > + */ > > > +struct zynqmp_afi { > > > + struct device *dev; > > > + struct device_node *of_node; > > > + struct reset_control *resets; > > > +}; > > > + > > > +/** > > > + * struct zynqmp_afi_configreg - AFI configuration registers info. > > > + * @reg: Name of the AFI configuration register. > > > + * @id: Register index value. > > > + */ > > > +struct zynqmp_afi_configreg { > > > + char *reg; > > > + u32 id; > > > +}; > > > + > > > +static struct zynqmp_afi_configreg afi_cfgreg[] = { > > > + {.reg = "xlnx,afi-fm0-rd-bus-width", .id = AFIFM0_RDCTRL}, > > > + {.reg = "xlnx,afi-fm1-rd-bus-width", .id = AFIFM1_RDCTRL}, > > > + {.reg = "xlnx,afi-fm2-rd-bus-width", .id = AFIFM2_RDCTRL}, > > > + {.reg = "xlnx,afi-fm3-rd-bus-width", .id = AFIFM3_RDCTRL}, > > > + {.reg = "xlnx,afi-fm4-rd-bus-width", .id = AFIFM4_RDCTRL}, > > > + {.reg = "xlnx,afi-fm5-rd-bus-width", .id = AFIFM5_RDCTRL}, > > > + {.reg = "xlnx,afi-fm6-rd-bus-width", .id = AFIFM6_RDCTRL}, > > > + {.reg = "xlnx,afi-fm0-wr-bus-width", .id = AFIFM0_WRCTRL}, > > > + {.reg = "xlnx,afi-fm1-wr-bus-width", .id = AFIFM1_WRCTRL}, > > > + {.reg = "xlnx,afi-fm2-wr-bus-width", .id = AFIFM2_WRCTRL}, > > > + {.reg = "xlnx,afi-fm3-wr-bus-width", .id = AFIFM3_WRCTRL}, > > > + {.reg = "xlnx,afi-fm4-wr-bus-width", .id = AFIFM4_WRCTRL}, > > > + {.reg = "xlnx,afi-fm5-wr-bus-width", .id = AFIFM5_WRCTRL}, > > > + {.reg = "xlnx,afi-fm6-wr-bus-width", .id = AFIFM6_WRCTRL}, > > > + {.reg = "xlnx,afi-fs-ss0-bus-width", .id = AFIFS}, > > > + {.reg = "xlnx,afi-fs-ss2-bus-width", .id = AFIFS_SS2}, > > > + {} > > > +}; > > > + > > > +static int zynqmp_afi_config(struct zynqmp_afi *afi_data) { > > > + struct zynqmp_afi_configreg *cfgptr = afi_cfgreg; > > > + struct device_node *np = afi_data->of_node; > > > + u32 afi_ss0_val, afi_ss1_val, bus_width; > > > + int ret; > > > + > > > + while (cfgptr->reg) { > > > + ret = of_property_read_u32(np, cfgptr->reg, &bus_width); > > > + if (!ret) { > > > + if (cfgptr->id == AFIFS_SS2) { > > > + if (bus_width == 32) > > > + ret = zynqmp_pm_afi(AFIFS_SS2, > > > + AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL); > > > + else if (bus_width == 64) > > > + ret = zynqmp_pm_afi(AFIFS_SS2, > > > + > > AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL); > > > + else if (bus_width == 128) > > > + ret = zynqmp_pm_afi(AFIFS_SS2, > > > + > > AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL); > > > + else > > > + return -EINVAL; > > > + } else if (cfgptr->id == AFIFS) { > > > + if (bus_width == 32) > > > + afi_ss0_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; > > > + else if (bus_width == 64) > > > + afi_ss0_val = > > AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL; > > > + else if (bus_width == 128) > > > + afi_ss0_val = > > AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL; > > > + else > > > + return -EINVAL; > > > + > > > + ret = of_property_read_u32(np, "xlnx,afi-fs-ss1-bus- > > width", > > > + &bus_width); > > > + if (!ret) { > > > + if (bus_width == 32) > > > + afi_ss1_val = > > AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; > > > + else if (bus_width == 64) > > > + afi_ss1_val = > > AFIFS_SS1_BUS_WIDTH_64_CONFIG_VAL; > > > + else if (bus_width == 128) > > > + afi_ss1_val = > > AFIFS_SS1_BUS_WIDTH_128_CONFIG_VAL; > > > + else > > > + return -EINVAL; > > > + > > > + ret = zynqmp_pm_afi(AFIFS, afi_ss1_val | > > afi_ss0_val); > > > + } > > > + } else { > > > + if (bus_width == 32) > > > + ret = zynqmp_pm_afi(cfgptr->id, > > > + AFIFM_BUS_WIDTH_32_CONFIG_VAL); > > > + else if (bus_width == 64) > > > + ret = zynqmp_pm_afi(cfgptr->id, > > > + AFIFM_BUS_WIDTH_64_CONFIG_VAL); > > > + else if (bus_width == 128) > > > + ret = zynqmp_pm_afi(cfgptr->id, > > > + AFIFM_BUS_WIDTH_128_CONFIG_VAL); > > > + else > > > + return -EINVAL; > > > + } > > > + } > > > + cfgptr++; > > > + } > > > + > > > + return 0; > > > +} > > > + > > > +static int zynqmp_afi_enable_set(struct fpga_bridge *bridge, bool > > > +enable) { > > > + struct device_node *overlay = bridge->info->overlay; > > > + struct zynqmp_afi *priv = bridge->priv; > > > + int ret = 0; > > > + > > > + if (enable) { > > > + reset_control_reset(priv->resets); > > > + return 0; > > > + } > > > + > > > + of_node_get(overlay); > > > + priv->of_node = > > > + of_find_node_with_property(overlay, > > > + "xlnx,afi-fm0-rd-bus-width"); > > > > I'm a little confused here. The fpga_image_info.overlay is for fpga-region, but > > from your binding doc this property is for this afi device. You want to add > > another overlay targeting afi dev node during reprograming? > > > > Yes, it uses Overlay's(overlay targeting afi dev node). As I said above for design-to-design AFI configs I have concern on it. We should limit the overlay usage only on fpga_region, this is because we are changing the hardware in this region during reprograming. Adding overlays for other nodes could be easily abused, any changes could be made even not related to the fpga region. So if any cross device configurations should be made during reprograming, it should be initiated by fpga region driver through normal kernel APIs. Thanks, Yilun > relevant to the full region may change and these configs must be set prior to program the full region > once this overlay integrated to the live tree the existing afi config values will be replace with the new one's > > > > + if (priv->of_node) > > > + ret = zynqmp_afi_config(priv); > > > + of_node_put(priv->of_node); > > > + > > > + return ret; > > > +} > > > + > > > +static const struct fpga_bridge_ops zynqmp_afi_br_ops = { > > > + .enable_set = zynqmp_afi_enable_set, }; > > > + > > > +static const struct of_device_id zynqmp_afi_of_match[] = { > > > + { .compatible = "xlnx,zynqmp-afi-fpga" }, > > > + { }, > > > +}; > > > +MODULE_DEVICE_TABLE(of, zynqmp_afi_of_match); > > > + > > > +static int zynqmp_afi_probe(struct platform_device *pdev) { > > > + struct device *dev = &pdev->dev; > > > + struct zynqmp_afi *priv; > > > + struct fpga_bridge *br; > > > + > > > + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); > > > + if (!priv) > > > + return -ENOMEM; > > > + > > > + priv->dev = dev; > > > + > > > + priv->resets = > > devm_reset_control_array_get_optional_exclusive(&pdev->dev); > > > + if (IS_ERR(priv->resets)) > > > + return PTR_ERR(priv->resets); > > > + > > > + br = fpga_bridge_register(dev, "Xilinx ZynqMP AFI", > > > + &zynqmp_afi_br_ops, priv); > > > + if (IS_ERR(br)) { > > > + dev_err(dev, "unable to register Xilinx ZynqMP AFI"); > > > > Need a "\n" at the end? > > > > Will fix. > > Regards, > Navakishore. >
On 2022-09-01 at 11:53:29 +0200, Marco Pagani wrote: > Hi Nava, > > On 2022-08-30 11:19, Manne, Nava kishore wrote: > > Hi Yilun, > > > > Please find my response inline. > > > >> -----Original Message----- > >> From: Xu Yilun <yilun.xu@intel.com> > >> Sent: Saturday, August 27, 2022 5:56 PM > >> To: Manne, Nava kishore <nava.kishore.manne@amd.com> > >> Cc: git (AMD-Xilinx) <git@amd.com>; robh+dt@kernel.org; > >> krzysztof.kozlowski+dt@linaro.org; michal.simek@xilinx.com; > >> mdf@kernel.org; hao.wu@intel.com; trix@redhat.com; > >> p.zabel@pengutronix.de; gregkh@linuxfoundation.org; > >> ronak.jain@xilinx.com; rajan.vaja@xilinx.com; > >> abhyuday.godhasara@xilinx.com; piyush.mehta@xilinx.com; > >> lakshmi.sai.krishna.potthuri@xilinx.com; harsha.harsha@xilinx.com; > >> linus.walleij@linaro.org; nava.manne@xilinx.com; > >> devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- > >> kernel@vger.kernel.org; linux-fpga@vger.kernel.org > >> Subject: Re: [PATCH 4/4] fpga: zynqmp: Add afi config driver > >> > >> CAUTION: This message has originated from an External Source. Please use > >> proper judgment and caution when opening attachments, clicking links, or > >> responding to this email. > >> > >> > >> On 2022-08-24 at 09:25:42 +0530, Nava kishore Manne wrote: > >>> Add zynqmp AXI FIFO interface(AFI) config driver. This is useful for > >>> the configuration of the PS-PL interface on Zynq US+ MPSoC platform. > >> > >> Please help illustrate how to use the device for FPGA reprogramming, why it > >> should be implemented as an FPGA bridge. > >> > >> From the code I actually didn't see any operation that gates the fpga-region > >> from other part of the machine. > >> > > > > The Zynq UltraScale MPSoC family consists of a system-on-chip (SoC) style integrated processing system (PS) > > and a Programmable Logic (PL) unit, providing an extensible and flexible SoC solution on a single die. > > Xilinx Zynq US+ MPSoC connect the PS to the programmable logic (PL) through the AXI port. > > This AXI port helps to establish the data path between the PS and PL (Here AXI Interface act as a Gating between PS and PL) > > and this AXI port configuration vary from design to design. In-order to establish the proper communication path between > > PS and PL (Full region), the AXI port data path should be configured with proper values priories to load the full region. > > > > Will update the description in v2. > > Are you implementing your AFI driver as a Bridge because you want to > change the configuration of the AXI HP interfaces exported by the PS > every time you reconfigure the full fabric? > > I understand the need to change the configuration of the PS-PL > interface at each full reconfiguration to ensure that the parameters > of the AXI ports exported by the PS (like the widths of data read > and write channels) matches the configuration of the master AXI ports > exported by the PL design. However, it seems to me that performing this > configuration doesn't fit the role of the FPGA Bridge, whose sole > responsibility should be gating the Region's interface during > reconfiguration. > > I think this need could be addressed by adding a new component to the > FPGA subsystem called "FPGA Adapter". The Adapter will be an optional > component associated with a Region like a Bridge. It will be responsible > for changing the configuration of its Region's static interface > (or PS/HPS/DRAM interface for the full FPGA) to match the interface > exported by the specific reconfigurable module (or full static design). I saw the Documentation/driver_api/interconnect.rst, but didn't look deep into it. For this AFI case, it sets the bus width, is it OK to use it? Thanks, Yilun > Moreover, besides bus-level properties like address/data width and > protocol conversion, the Adapter could also be used to configure > system-level properties. For instance, the designer may use it to change > the memory access policy for the specific reconfigurable module if it > uses bus mastering. > > > > >>> > >>> Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com> > >>> --- > >>> MAINTAINERS | 6 ++ > >>> drivers/fpga/Kconfig | 13 +++ > >>> drivers/fpga/Makefile | 1 + > >>> drivers/fpga/zynqmp-afi.c | 211 > >>> ++++++++++++++++++++++++++++++++++++++ > >>> 4 files changed, 231 insertions(+) > >>> create mode 100644 drivers/fpga/zynqmp-afi.c > >>> > >>> diff --git a/MAINTAINERS b/MAINTAINERS index > >>> 20ffac651214..957e753e6406 100644 > >>> --- a/MAINTAINERS > >>> +++ b/MAINTAINERS > >>> @@ -8032,6 +8032,12 @@ F: Documentation/fpga/ > >>> F: drivers/fpga/ > >>> F: include/linux/fpga/ > >>> > >>> +FPGA ZYNQMP PS-PL BRIDGE DRIVER > >>> +M: Nava kishore Manne <nava.kishore.manne@amd.com> > >>> +S: Supported > >>> +F: Documentation/devicetree/bindings/fpga/xlnx,zynqmp-afi-fpga.yaml > >>> +F: drivers/fpga/zynqmp-afi.c > >>> + > >>> INTEL MAX10 BMC SECURE UPDATES > >>> M: Russ Weight <russell.h.weight@intel.com> > >>> L: linux-fpga@vger.kernel.org > >>> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index > >>> 6c416955da53..c08794d30fb5 100644 > >>> --- a/drivers/fpga/Kconfig > >>> +++ b/drivers/fpga/Kconfig > >>> @@ -130,6 +130,19 @@ config XILINX_PR_DECOUPLER > >>> reconfiguration, preventing the system deadlock that can > >>> occur if AXI transactions are interrupted by DFX. > >>> > >>> +config ZYNQMP_AFI > >>> + tristate "Xilinx ZYNQMP AFI support" > >>> + depends on FPGA_BRIDGE > >>> + help > >>> + Say Y to enable drivers to handle the PS-PL clocks configurations > >>> + and PS-PL Bus-width. Xilinx Zynq US+ MPSoC connect the PS to the > >>> + programmable logic (PL) through the AXI port. This AXI port helps > >>> + to establish the data path between the PS and PL. > >>> + In-order to establish the proper communication path between PS and > >> PL, > >>> + the AXI port data path should be configured with the proper Bus- > >> width > >>> + values and it will also handles the PS-PL reset signals to reset the > >>> + PL domain. > >> > >> Same concern, please describe its relationship to FPGA reprogramming. > >> > > > > Same as above. > > Will update the description in v2. > > > >>> + > >>> config FPGA_REGION > >>> tristate "FPGA Region" > >>> depends on FPGA_BRIDGE > >>> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index > >>> 42ae8b58abce..94cfe60972db 100644 > >>> --- a/drivers/fpga/Makefile > >>> +++ b/drivers/fpga/Makefile > >>> @@ -31,6 +31,7 @@ obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o > >>> obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera- > >> fpga2sdram.o > >>> obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o > >>> obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o > >>> +obj-$(CONFIG_ZYNQMP_AFI) += zynqmp-afi.o > >>> > >>> # High Level Interfaces > >>> obj-$(CONFIG_FPGA_REGION) += fpga-region.o > >>> diff --git a/drivers/fpga/zynqmp-afi.c b/drivers/fpga/zynqmp-afi.c new > >>> file mode 100644 index 000000000000..bc975d304039 > >>> --- /dev/null > >>> +++ b/drivers/fpga/zynqmp-afi.c > >>> @@ -0,0 +1,211 @@ > >>> +// SPDX-License-Identifier: GPL-2.0 > >>> +/* > >>> + * Copyright (C) 2022 Xilinx, Inc. > >>> + */ > >>> + > >>> +#include <linux/err.h> > >>> +#include <linux/firmware/xlnx-zynqmp.h> #include > >>> +<linux/fpga/fpga-bridge.h> #include <linux/io.h> #include > >>> +<linux/module.h> #include <linux/of.h> #include > >>> +<linux/platform_device.h> #include <linux/reset.h> #include > >>> +<linux/slab.h> > >>> + > >>> +/* Registers and special values for doing register-based operations */ > >>> +#define AFI_RDCHAN_CTRL_OFFSET 0x00 > >>> +#define AFI_WRCHAN_CTRL_OFFSET 0x14 > >>> +#define AFI_BUSWIDTH_MASK BIT(0) > >>> + > >>> +/** > >>> + * struct zynqmp_afi - AFI register description. > >>> + * @dev: device that owns this. > >>> + * @of_node: Device Tree overlay. > >>> + * @resets: Pointer to the reset control for ps-pl resets. > >>> + */ > >>> +struct zynqmp_afi { > >>> + struct device *dev; > >>> + struct device_node *of_node; > >>> + struct reset_control *resets; > >>> +}; > >>> + > >>> +/** > >>> + * struct zynqmp_afi_configreg - AFI configuration registers info. > >>> + * @reg: Name of the AFI configuration register. > >>> + * @id: Register index value. > >>> + */ > >>> +struct zynqmp_afi_configreg { > >>> + char *reg; > >>> + u32 id; > >>> +}; > >>> + > >>> +static struct zynqmp_afi_configreg afi_cfgreg[] = { > >>> + {.reg = "xlnx,afi-fm0-rd-bus-width", .id = AFIFM0_RDCTRL}, > >>> + {.reg = "xlnx,afi-fm1-rd-bus-width", .id = AFIFM1_RDCTRL}, > >>> + {.reg = "xlnx,afi-fm2-rd-bus-width", .id = AFIFM2_RDCTRL}, > >>> + {.reg = "xlnx,afi-fm3-rd-bus-width", .id = AFIFM3_RDCTRL}, > >>> + {.reg = "xlnx,afi-fm4-rd-bus-width", .id = AFIFM4_RDCTRL}, > >>> + {.reg = "xlnx,afi-fm5-rd-bus-width", .id = AFIFM5_RDCTRL}, > >>> + {.reg = "xlnx,afi-fm6-rd-bus-width", .id = AFIFM6_RDCTRL}, > >>> + {.reg = "xlnx,afi-fm0-wr-bus-width", .id = AFIFM0_WRCTRL}, > >>> + {.reg = "xlnx,afi-fm1-wr-bus-width", .id = AFIFM1_WRCTRL}, > >>> + {.reg = "xlnx,afi-fm2-wr-bus-width", .id = AFIFM2_WRCTRL}, > >>> + {.reg = "xlnx,afi-fm3-wr-bus-width", .id = AFIFM3_WRCTRL}, > >>> + {.reg = "xlnx,afi-fm4-wr-bus-width", .id = AFIFM4_WRCTRL}, > >>> + {.reg = "xlnx,afi-fm5-wr-bus-width", .id = AFIFM5_WRCTRL}, > >>> + {.reg = "xlnx,afi-fm6-wr-bus-width", .id = AFIFM6_WRCTRL}, > >>> + {.reg = "xlnx,afi-fs-ss0-bus-width", .id = AFIFS}, > >>> + {.reg = "xlnx,afi-fs-ss2-bus-width", .id = AFIFS_SS2}, > >>> + {} > >>> +}; > >>> + > >>> +static int zynqmp_afi_config(struct zynqmp_afi *afi_data) { > >>> + struct zynqmp_afi_configreg *cfgptr = afi_cfgreg; > >>> + struct device_node *np = afi_data->of_node; > >>> + u32 afi_ss0_val, afi_ss1_val, bus_width; > >>> + int ret; > >>> + > >>> + while (cfgptr->reg) { > >>> + ret = of_property_read_u32(np, cfgptr->reg, &bus_width); > >>> + if (!ret) { > >>> + if (cfgptr->id == AFIFS_SS2) { > >>> + if (bus_width == 32) > >>> + ret = zynqmp_pm_afi(AFIFS_SS2, > >>> + AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL); > >>> + else if (bus_width == 64) > >>> + ret = zynqmp_pm_afi(AFIFS_SS2, > >>> + > >> AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL); > >>> + else if (bus_width == 128) > >>> + ret = zynqmp_pm_afi(AFIFS_SS2, > >>> + > >> AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL); > >>> + else > >>> + return -EINVAL; > >>> + } else if (cfgptr->id == AFIFS) { > >>> + if (bus_width == 32) > >>> + afi_ss0_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; > >>> + else if (bus_width == 64) > >>> + afi_ss0_val = > >> AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL; > >>> + else if (bus_width == 128) > >>> + afi_ss0_val = > >> AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL; > >>> + else > >>> + return -EINVAL; > >>> + > >>> + ret = of_property_read_u32(np, "xlnx,afi-fs-ss1-bus- > >> width", > >>> + &bus_width); > >>> + if (!ret) { > >>> + if (bus_width == 32) > >>> + afi_ss1_val = > >> AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; > >>> + else if (bus_width == 64) > >>> + afi_ss1_val = > >> AFIFS_SS1_BUS_WIDTH_64_CONFIG_VAL; > >>> + else if (bus_width == 128) > >>> + afi_ss1_val = > >> AFIFS_SS1_BUS_WIDTH_128_CONFIG_VAL; > >>> + else > >>> + return -EINVAL; > >>> + > >>> + ret = zynqmp_pm_afi(AFIFS, afi_ss1_val | > >> afi_ss0_val); > >>> + } > >>> + } else { > >>> + if (bus_width == 32) > >>> + ret = zynqmp_pm_afi(cfgptr->id, > >>> + AFIFM_BUS_WIDTH_32_CONFIG_VAL); > >>> + else if (bus_width == 64) > >>> + ret = zynqmp_pm_afi(cfgptr->id, > >>> + AFIFM_BUS_WIDTH_64_CONFIG_VAL); > >>> + else if (bus_width == 128) > >>> + ret = zynqmp_pm_afi(cfgptr->id, > >>> + AFIFM_BUS_WIDTH_128_CONFIG_VAL); > >>> + else > >>> + return -EINVAL; > >>> + } > >>> + } > >>> + cfgptr++; > >>> + } > >>> + > >>> + return 0; > >>> +} > >>> + > >>> +static int zynqmp_afi_enable_set(struct fpga_bridge *bridge, bool > >>> +enable) { > >>> + struct device_node *overlay = bridge->info->overlay; > >>> + struct zynqmp_afi *priv = bridge->priv; > >>> + int ret = 0; > >>> + > >>> + if (enable) { > >>> + reset_control_reset(priv->resets); > >>> + return 0; > >>> + } > >>> + > >>> + of_node_get(overlay); > >>> + priv->of_node = > >>> + of_find_node_with_property(overlay, > >>> + "xlnx,afi-fm0-rd-bus-width"); > >> > >> I'm a little confused here. The fpga_image_info.overlay is for fpga-region, but > >> from your binding doc this property is for this afi device. You want to add > >> another overlay targeting afi dev node during reprograming? > >> > > > > Yes, it uses Overlay's(overlay targeting afi dev node). As I said above for design-to-design AFI configs > > relevant to the full region may change and these configs must be set prior to program the full region > > once this overlay integrated to the live tree the existing afi config values will be replace with the new one's > > > >>> + if (priv->of_node) > >>> + ret = zynqmp_afi_config(priv); > >>> + of_node_put(priv->of_node); > >>> + > >>> + return ret; > >>> +} > >>> + > >>> +static const struct fpga_bridge_ops zynqmp_afi_br_ops = { > >>> + .enable_set = zynqmp_afi_enable_set, }; > >>> + > >>> +static const struct of_device_id zynqmp_afi_of_match[] = { > >>> + { .compatible = "xlnx,zynqmp-afi-fpga" }, > >>> + { }, > >>> +}; > >>> +MODULE_DEVICE_TABLE(of, zynqmp_afi_of_match); > >>> + > >>> +static int zynqmp_afi_probe(struct platform_device *pdev) { > >>> + struct device *dev = &pdev->dev; > >>> + struct zynqmp_afi *priv; > >>> + struct fpga_bridge *br; > >>> + > >>> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); > >>> + if (!priv) > >>> + return -ENOMEM; > >>> + > >>> + priv->dev = dev; > >>> + > >>> + priv->resets = > >> devm_reset_control_array_get_optional_exclusive(&pdev->dev); > >>> + if (IS_ERR(priv->resets)) > >>> + return PTR_ERR(priv->resets); > >>> + > >>> + br = fpga_bridge_register(dev, "Xilinx ZynqMP AFI", > >>> + &zynqmp_afi_br_ops, priv); > >>> + if (IS_ERR(br)) { > >>> + dev_err(dev, "unable to register Xilinx ZynqMP AFI"); > >> > >> Need a "\n" at the end? > >> > > > > Will fix. > > > > Regards, > > Navakishore. > > > > Thanks, > Marco >
On 2022-09-03 19:44, Xu Yilun wrote: > On 2022-09-01 at 11:53:29 +0200, Marco Pagani wrote: >> Hi Nava, >> >> On 2022-08-30 11:19, Manne, Nava kishore wrote: >>> Hi Yilun, >>> >>> Please find my response inline. >>> >>>> -----Original Message----- >>>> From: Xu Yilun <yilun.xu@intel.com> >>>> Sent: Saturday, August 27, 2022 5:56 PM >>>> To: Manne, Nava kishore <nava.kishore.manne@amd.com> >>>> Cc: git (AMD-Xilinx) <git@amd.com>; robh+dt@kernel.org; >>>> krzysztof.kozlowski+dt@linaro.org; michal.simek@xilinx.com; >>>> mdf@kernel.org; hao.wu@intel.com; trix@redhat.com; >>>> p.zabel@pengutronix.de; gregkh@linuxfoundation.org; >>>> ronak.jain@xilinx.com; rajan.vaja@xilinx.com; >>>> abhyuday.godhasara@xilinx.com; piyush.mehta@xilinx.com; >>>> lakshmi.sai.krishna.potthuri@xilinx.com; harsha.harsha@xilinx.com; >>>> linus.walleij@linaro.org; nava.manne@xilinx.com; >>>> devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- >>>> kernel@vger.kernel.org; linux-fpga@vger.kernel.org >>>> Subject: Re: [PATCH 4/4] fpga: zynqmp: Add afi config driver >>>> >>>> CAUTION: This message has originated from an External Source. Please use >>>> proper judgment and caution when opening attachments, clicking links, or >>>> responding to this email. >>>> >>>> >>>> On 2022-08-24 at 09:25:42 +0530, Nava kishore Manne wrote: >>>>> Add zynqmp AXI FIFO interface(AFI) config driver. This is useful for >>>>> the configuration of the PS-PL interface on Zynq US+ MPSoC platform. >>>> >>>> Please help illustrate how to use the device for FPGA reprogramming, why it >>>> should be implemented as an FPGA bridge. >>>> >>>> From the code I actually didn't see any operation that gates the fpga-region >>>> from other part of the machine. >>>> >>> >>> The Zynq UltraScale MPSoC family consists of a system-on-chip (SoC) style integrated processing system (PS) >>> and a Programmable Logic (PL) unit, providing an extensible and flexible SoC solution on a single die. >>> Xilinx Zynq US+ MPSoC connect the PS to the programmable logic (PL) through the AXI port. >>> This AXI port helps to establish the data path between the PS and PL (Here AXI Interface act as a Gating between PS and PL) >>> and this AXI port configuration vary from design to design. In-order to establish the proper communication path between >>> PS and PL (Full region), the AXI port data path should be configured with proper values priories to load the full region. >>> >>> Will update the description in v2. >> >> Are you implementing your AFI driver as a Bridge because you want to >> change the configuration of the AXI HP interfaces exported by the PS >> every time you reconfigure the full fabric? >> >> I understand the need to change the configuration of the PS-PL >> interface at each full reconfiguration to ensure that the parameters >> of the AXI ports exported by the PS (like the widths of data read >> and write channels) matches the configuration of the master AXI ports >> exported by the PL design. However, it seems to me that performing this >> configuration doesn't fit the role of the FPGA Bridge, whose sole >> responsibility should be gating the Region's interface during >> reconfiguration. >> >> I think this need could be addressed by adding a new component to the >> FPGA subsystem called "FPGA Adapter". The Adapter will be an optional >> component associated with a Region like a Bridge. It will be responsible >> for changing the configuration of its Region's static interface >> (or PS/HPS/DRAM interface for the full FPGA) to match the interface >> exported by the specific reconfigurable module (or full static design). > > I saw the Documentation/driver_api/interconnect.rst, but didn't look deep > into it. For this AFI case, it sets the bus width, is it OK to use it? > > Thanks, > Yilun Thanks for pointing me to the interconnect subsystem. I'm currently investigating if it's possible to implement a driver for the AFI (and possibly other PS interconnects with their QoS regulators) using the subsystem. Thanks, Marco > >> Moreover, besides bus-level properties like address/data width and >> protocol conversion, the Adapter could also be used to configure >> system-level properties. For instance, the designer may use it to change >> the memory access policy for the specific reconfigurable module if it >> uses bus mastering. >> >>> >>>>> >>>>> Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com> >>>>> --- >>>>> MAINTAINERS | 6 ++ >>>>> drivers/fpga/Kconfig | 13 +++ >>>>> drivers/fpga/Makefile | 1 + >>>>> drivers/fpga/zynqmp-afi.c | 211 >>>>> ++++++++++++++++++++++++++++++++++++++ >>>>> 4 files changed, 231 insertions(+) >>>>> create mode 100644 drivers/fpga/zynqmp-afi.c >>>>> >>>>> diff --git a/MAINTAINERS b/MAINTAINERS index >>>>> 20ffac651214..957e753e6406 100644 >>>>> --- a/MAINTAINERS >>>>> +++ b/MAINTAINERS >>>>> @@ -8032,6 +8032,12 @@ F: Documentation/fpga/ >>>>> F: drivers/fpga/ >>>>> F: include/linux/fpga/ >>>>> >>>>> +FPGA ZYNQMP PS-PL BRIDGE DRIVER >>>>> +M: Nava kishore Manne <nava.kishore.manne@amd.com> >>>>> +S: Supported >>>>> +F: Documentation/devicetree/bindings/fpga/xlnx,zynqmp-afi-fpga.yaml >>>>> +F: drivers/fpga/zynqmp-afi.c >>>>> + >>>>> INTEL MAX10 BMC SECURE UPDATES >>>>> M: Russ Weight <russell.h.weight@intel.com> >>>>> L: linux-fpga@vger.kernel.org >>>>> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index >>>>> 6c416955da53..c08794d30fb5 100644 >>>>> --- a/drivers/fpga/Kconfig >>>>> +++ b/drivers/fpga/Kconfig >>>>> @@ -130,6 +130,19 @@ config XILINX_PR_DECOUPLER >>>>> reconfiguration, preventing the system deadlock that can >>>>> occur if AXI transactions are interrupted by DFX. >>>>> >>>>> +config ZYNQMP_AFI >>>>> + tristate "Xilinx ZYNQMP AFI support" >>>>> + depends on FPGA_BRIDGE >>>>> + help >>>>> + Say Y to enable drivers to handle the PS-PL clocks configurations >>>>> + and PS-PL Bus-width. Xilinx Zynq US+ MPSoC connect the PS to the >>>>> + programmable logic (PL) through the AXI port. This AXI port helps >>>>> + to establish the data path between the PS and PL. >>>>> + In-order to establish the proper communication path between PS and >>>> PL, >>>>> + the AXI port data path should be configured with the proper Bus- >>>> width >>>>> + values and it will also handles the PS-PL reset signals to reset the >>>>> + PL domain. >>>> >>>> Same concern, please describe its relationship to FPGA reprogramming. >>>> >>> >>> Same as above. >>> Will update the description in v2. >>> >>>>> + >>>>> config FPGA_REGION >>>>> tristate "FPGA Region" >>>>> depends on FPGA_BRIDGE >>>>> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index >>>>> 42ae8b58abce..94cfe60972db 100644 >>>>> --- a/drivers/fpga/Makefile >>>>> +++ b/drivers/fpga/Makefile >>>>> @@ -31,6 +31,7 @@ obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o >>>>> obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera- >>>> fpga2sdram.o >>>>> obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o >>>>> obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o >>>>> +obj-$(CONFIG_ZYNQMP_AFI) += zynqmp-afi.o >>>>> >>>>> # High Level Interfaces >>>>> obj-$(CONFIG_FPGA_REGION) += fpga-region.o >>>>> diff --git a/drivers/fpga/zynqmp-afi.c b/drivers/fpga/zynqmp-afi.c new >>>>> file mode 100644 index 000000000000..bc975d304039 >>>>> --- /dev/null >>>>> +++ b/drivers/fpga/zynqmp-afi.c >>>>> @@ -0,0 +1,211 @@ >>>>> +// SPDX-License-Identifier: GPL-2.0 >>>>> +/* >>>>> + * Copyright (C) 2022 Xilinx, Inc. >>>>> + */ >>>>> + >>>>> +#include <linux/err.h> >>>>> +#include <linux/firmware/xlnx-zynqmp.h> #include >>>>> +<linux/fpga/fpga-bridge.h> #include <linux/io.h> #include >>>>> +<linux/module.h> #include <linux/of.h> #include >>>>> +<linux/platform_device.h> #include <linux/reset.h> #include >>>>> +<linux/slab.h> >>>>> + >>>>> +/* Registers and special values for doing register-based operations */ >>>>> +#define AFI_RDCHAN_CTRL_OFFSET 0x00 >>>>> +#define AFI_WRCHAN_CTRL_OFFSET 0x14 >>>>> +#define AFI_BUSWIDTH_MASK BIT(0) >>>>> + >>>>> +/** >>>>> + * struct zynqmp_afi - AFI register description. >>>>> + * @dev: device that owns this. >>>>> + * @of_node: Device Tree overlay. >>>>> + * @resets: Pointer to the reset control for ps-pl resets. >>>>> + */ >>>>> +struct zynqmp_afi { >>>>> + struct device *dev; >>>>> + struct device_node *of_node; >>>>> + struct reset_control *resets; >>>>> +}; >>>>> + >>>>> +/** >>>>> + * struct zynqmp_afi_configreg - AFI configuration registers info. >>>>> + * @reg: Name of the AFI configuration register. >>>>> + * @id: Register index value. >>>>> + */ >>>>> +struct zynqmp_afi_configreg { >>>>> + char *reg; >>>>> + u32 id; >>>>> +}; >>>>> + >>>>> +static struct zynqmp_afi_configreg afi_cfgreg[] = { >>>>> + {.reg = "xlnx,afi-fm0-rd-bus-width", .id = AFIFM0_RDCTRL}, >>>>> + {.reg = "xlnx,afi-fm1-rd-bus-width", .id = AFIFM1_RDCTRL}, >>>>> + {.reg = "xlnx,afi-fm2-rd-bus-width", .id = AFIFM2_RDCTRL}, >>>>> + {.reg = "xlnx,afi-fm3-rd-bus-width", .id = AFIFM3_RDCTRL}, >>>>> + {.reg = "xlnx,afi-fm4-rd-bus-width", .id = AFIFM4_RDCTRL}, >>>>> + {.reg = "xlnx,afi-fm5-rd-bus-width", .id = AFIFM5_RDCTRL}, >>>>> + {.reg = "xlnx,afi-fm6-rd-bus-width", .id = AFIFM6_RDCTRL}, >>>>> + {.reg = "xlnx,afi-fm0-wr-bus-width", .id = AFIFM0_WRCTRL}, >>>>> + {.reg = "xlnx,afi-fm1-wr-bus-width", .id = AFIFM1_WRCTRL}, >>>>> + {.reg = "xlnx,afi-fm2-wr-bus-width", .id = AFIFM2_WRCTRL}, >>>>> + {.reg = "xlnx,afi-fm3-wr-bus-width", .id = AFIFM3_WRCTRL}, >>>>> + {.reg = "xlnx,afi-fm4-wr-bus-width", .id = AFIFM4_WRCTRL}, >>>>> + {.reg = "xlnx,afi-fm5-wr-bus-width", .id = AFIFM5_WRCTRL}, >>>>> + {.reg = "xlnx,afi-fm6-wr-bus-width", .id = AFIFM6_WRCTRL}, >>>>> + {.reg = "xlnx,afi-fs-ss0-bus-width", .id = AFIFS}, >>>>> + {.reg = "xlnx,afi-fs-ss2-bus-width", .id = AFIFS_SS2}, >>>>> + {} >>>>> +}; >>>>> + >>>>> +static int zynqmp_afi_config(struct zynqmp_afi *afi_data) { >>>>> + struct zynqmp_afi_configreg *cfgptr = afi_cfgreg; >>>>> + struct device_node *np = afi_data->of_node; >>>>> + u32 afi_ss0_val, afi_ss1_val, bus_width; >>>>> + int ret; >>>>> + >>>>> + while (cfgptr->reg) { >>>>> + ret = of_property_read_u32(np, cfgptr->reg, &bus_width); >>>>> + if (!ret) { >>>>> + if (cfgptr->id == AFIFS_SS2) { >>>>> + if (bus_width == 32) >>>>> + ret = zynqmp_pm_afi(AFIFS_SS2, >>>>> + AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL); >>>>> + else if (bus_width == 64) >>>>> + ret = zynqmp_pm_afi(AFIFS_SS2, >>>>> + >>>> AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL); >>>>> + else if (bus_width == 128) >>>>> + ret = zynqmp_pm_afi(AFIFS_SS2, >>>>> + >>>> AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL); >>>>> + else >>>>> + return -EINVAL; >>>>> + } else if (cfgptr->id == AFIFS) { >>>>> + if (bus_width == 32) >>>>> + afi_ss0_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; >>>>> + else if (bus_width == 64) >>>>> + afi_ss0_val = >>>> AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL; >>>>> + else if (bus_width == 128) >>>>> + afi_ss0_val = >>>> AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL; >>>>> + else >>>>> + return -EINVAL; >>>>> + >>>>> + ret = of_property_read_u32(np, "xlnx,afi-fs-ss1-bus- >>>> width", >>>>> + &bus_width); >>>>> + if (!ret) { >>>>> + if (bus_width == 32) >>>>> + afi_ss1_val = >>>> AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; >>>>> + else if (bus_width == 64) >>>>> + afi_ss1_val = >>>> AFIFS_SS1_BUS_WIDTH_64_CONFIG_VAL; >>>>> + else if (bus_width == 128) >>>>> + afi_ss1_val = >>>> AFIFS_SS1_BUS_WIDTH_128_CONFIG_VAL; >>>>> + else >>>>> + return -EINVAL; >>>>> + >>>>> + ret = zynqmp_pm_afi(AFIFS, afi_ss1_val | >>>> afi_ss0_val); >>>>> + } >>>>> + } else { >>>>> + if (bus_width == 32) >>>>> + ret = zynqmp_pm_afi(cfgptr->id, >>>>> + AFIFM_BUS_WIDTH_32_CONFIG_VAL); >>>>> + else if (bus_width == 64) >>>>> + ret = zynqmp_pm_afi(cfgptr->id, >>>>> + AFIFM_BUS_WIDTH_64_CONFIG_VAL); >>>>> + else if (bus_width == 128) >>>>> + ret = zynqmp_pm_afi(cfgptr->id, >>>>> + AFIFM_BUS_WIDTH_128_CONFIG_VAL); >>>>> + else >>>>> + return -EINVAL; >>>>> + } >>>>> + } >>>>> + cfgptr++; >>>>> + } >>>>> + >>>>> + return 0; >>>>> +} >>>>> + >>>>> +static int zynqmp_afi_enable_set(struct fpga_bridge *bridge, bool >>>>> +enable) { >>>>> + struct device_node *overlay = bridge->info->overlay; >>>>> + struct zynqmp_afi *priv = bridge->priv; >>>>> + int ret = 0; >>>>> + >>>>> + if (enable) { >>>>> + reset_control_reset(priv->resets); >>>>> + return 0; >>>>> + } >>>>> + >>>>> + of_node_get(overlay); >>>>> + priv->of_node = >>>>> + of_find_node_with_property(overlay, >>>>> + "xlnx,afi-fm0-rd-bus-width"); >>>> >>>> I'm a little confused here. The fpga_image_info.overlay is for fpga-region, but >>>> from your binding doc this property is for this afi device. You want to add >>>> another overlay targeting afi dev node during reprograming? >>>> >>> >>> Yes, it uses Overlay's(overlay targeting afi dev node). As I said above for design-to-design AFI configs >>> relevant to the full region may change and these configs must be set prior to program the full region >>> once this overlay integrated to the live tree the existing afi config values will be replace with the new one's >>> >>>>> + if (priv->of_node) >>>>> + ret = zynqmp_afi_config(priv); >>>>> + of_node_put(priv->of_node); >>>>> + >>>>> + return ret; >>>>> +} >>>>> + >>>>> +static const struct fpga_bridge_ops zynqmp_afi_br_ops = { >>>>> + .enable_set = zynqmp_afi_enable_set, }; >>>>> + >>>>> +static const struct of_device_id zynqmp_afi_of_match[] = { >>>>> + { .compatible = "xlnx,zynqmp-afi-fpga" }, >>>>> + { }, >>>>> +}; >>>>> +MODULE_DEVICE_TABLE(of, zynqmp_afi_of_match); >>>>> + >>>>> +static int zynqmp_afi_probe(struct platform_device *pdev) { >>>>> + struct device *dev = &pdev->dev; >>>>> + struct zynqmp_afi *priv; >>>>> + struct fpga_bridge *br; >>>>> + >>>>> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); >>>>> + if (!priv) >>>>> + return -ENOMEM; >>>>> + >>>>> + priv->dev = dev; >>>>> + >>>>> + priv->resets = >>>> devm_reset_control_array_get_optional_exclusive(&pdev->dev); >>>>> + if (IS_ERR(priv->resets)) >>>>> + return PTR_ERR(priv->resets); >>>>> + >>>>> + br = fpga_bridge_register(dev, "Xilinx ZynqMP AFI", >>>>> + &zynqmp_afi_br_ops, priv); >>>>> + if (IS_ERR(br)) { >>>>> + dev_err(dev, "unable to register Xilinx ZynqMP AFI"); >>>> >>>> Need a "\n" at the end? >>>> >>> >>> Will fix. >>> >>> Regards, >>> Navakishore. >>> >> >> Thanks, >> Marco >> >
diff --git a/MAINTAINERS b/MAINTAINERS index 20ffac651214..957e753e6406 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -8032,6 +8032,12 @@ F: Documentation/fpga/ F: drivers/fpga/ F: include/linux/fpga/ +FPGA ZYNQMP PS-PL BRIDGE DRIVER +M: Nava kishore Manne <nava.kishore.manne@amd.com> +S: Supported +F: Documentation/devicetree/bindings/fpga/xlnx,zynqmp-afi-fpga.yaml +F: drivers/fpga/zynqmp-afi.c + INTEL MAX10 BMC SECURE UPDATES M: Russ Weight <russell.h.weight@intel.com> L: linux-fpga@vger.kernel.org diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig index 6c416955da53..c08794d30fb5 100644 --- a/drivers/fpga/Kconfig +++ b/drivers/fpga/Kconfig @@ -130,6 +130,19 @@ config XILINX_PR_DECOUPLER reconfiguration, preventing the system deadlock that can occur if AXI transactions are interrupted by DFX. +config ZYNQMP_AFI + tristate "Xilinx ZYNQMP AFI support" + depends on FPGA_BRIDGE + help + Say Y to enable drivers to handle the PS-PL clocks configurations + and PS-PL Bus-width. Xilinx Zynq US+ MPSoC connect the PS to the + programmable logic (PL) through the AXI port. This AXI port helps + to establish the data path between the PS and PL. + In-order to establish the proper communication path between PS and PL, + the AXI port data path should be configured with the proper Bus-width + values and it will also handles the PS-PL reset signals to reset the + PL domain. + config FPGA_REGION tristate "FPGA Region" depends on FPGA_BRIDGE diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile index 42ae8b58abce..94cfe60972db 100644 --- a/drivers/fpga/Makefile +++ b/drivers/fpga/Makefile @@ -31,6 +31,7 @@ obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera-fpga2sdram.o obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o +obj-$(CONFIG_ZYNQMP_AFI) += zynqmp-afi.o # High Level Interfaces obj-$(CONFIG_FPGA_REGION) += fpga-region.o diff --git a/drivers/fpga/zynqmp-afi.c b/drivers/fpga/zynqmp-afi.c new file mode 100644 index 000000000000..bc975d304039 --- /dev/null +++ b/drivers/fpga/zynqmp-afi.c @@ -0,0 +1,211 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2022 Xilinx, Inc. + */ + +#include <linux/err.h> +#include <linux/firmware/xlnx-zynqmp.h> +#include <linux/fpga/fpga-bridge.h> +#include <linux/io.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/reset.h> +#include <linux/slab.h> + +/* Registers and special values for doing register-based operations */ +#define AFI_RDCHAN_CTRL_OFFSET 0x00 +#define AFI_WRCHAN_CTRL_OFFSET 0x14 +#define AFI_BUSWIDTH_MASK BIT(0) + +/** + * struct zynqmp_afi - AFI register description. + * @dev: device that owns this. + * @of_node: Device Tree overlay. + * @resets: Pointer to the reset control for ps-pl resets. + */ +struct zynqmp_afi { + struct device *dev; + struct device_node *of_node; + struct reset_control *resets; +}; + +/** + * struct zynqmp_afi_configreg - AFI configuration registers info. + * @reg: Name of the AFI configuration register. + * @id: Register index value. + */ +struct zynqmp_afi_configreg { + char *reg; + u32 id; +}; + +static struct zynqmp_afi_configreg afi_cfgreg[] = { + {.reg = "xlnx,afi-fm0-rd-bus-width", .id = AFIFM0_RDCTRL}, + {.reg = "xlnx,afi-fm1-rd-bus-width", .id = AFIFM1_RDCTRL}, + {.reg = "xlnx,afi-fm2-rd-bus-width", .id = AFIFM2_RDCTRL}, + {.reg = "xlnx,afi-fm3-rd-bus-width", .id = AFIFM3_RDCTRL}, + {.reg = "xlnx,afi-fm4-rd-bus-width", .id = AFIFM4_RDCTRL}, + {.reg = "xlnx,afi-fm5-rd-bus-width", .id = AFIFM5_RDCTRL}, + {.reg = "xlnx,afi-fm6-rd-bus-width", .id = AFIFM6_RDCTRL}, + {.reg = "xlnx,afi-fm0-wr-bus-width", .id = AFIFM0_WRCTRL}, + {.reg = "xlnx,afi-fm1-wr-bus-width", .id = AFIFM1_WRCTRL}, + {.reg = "xlnx,afi-fm2-wr-bus-width", .id = AFIFM2_WRCTRL}, + {.reg = "xlnx,afi-fm3-wr-bus-width", .id = AFIFM3_WRCTRL}, + {.reg = "xlnx,afi-fm4-wr-bus-width", .id = AFIFM4_WRCTRL}, + {.reg = "xlnx,afi-fm5-wr-bus-width", .id = AFIFM5_WRCTRL}, + {.reg = "xlnx,afi-fm6-wr-bus-width", .id = AFIFM6_WRCTRL}, + {.reg = "xlnx,afi-fs-ss0-bus-width", .id = AFIFS}, + {.reg = "xlnx,afi-fs-ss2-bus-width", .id = AFIFS_SS2}, + {} +}; + +static int zynqmp_afi_config(struct zynqmp_afi *afi_data) +{ + struct zynqmp_afi_configreg *cfgptr = afi_cfgreg; + struct device_node *np = afi_data->of_node; + u32 afi_ss0_val, afi_ss1_val, bus_width; + int ret; + + while (cfgptr->reg) { + ret = of_property_read_u32(np, cfgptr->reg, &bus_width); + if (!ret) { + if (cfgptr->id == AFIFS_SS2) { + if (bus_width == 32) + ret = zynqmp_pm_afi(AFIFS_SS2, + AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL); + else if (bus_width == 64) + ret = zynqmp_pm_afi(AFIFS_SS2, + AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL); + else if (bus_width == 128) + ret = zynqmp_pm_afi(AFIFS_SS2, + AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL); + else + return -EINVAL; + } else if (cfgptr->id == AFIFS) { + if (bus_width == 32) + afi_ss0_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; + else if (bus_width == 64) + afi_ss0_val = AFIFS_SS0_SS2_BUS_WIDTH_64_CONFIG_VAL; + else if (bus_width == 128) + afi_ss0_val = AFIFS_SS0_SS2_BUS_WIDTH_128_CONFIG_VAL; + else + return -EINVAL; + + ret = of_property_read_u32(np, "xlnx,afi-fs-ss1-bus-width", + &bus_width); + if (!ret) { + if (bus_width == 32) + afi_ss1_val = AFIFS_SS_BUS_WIDTH_32_CONFIG_VAL; + else if (bus_width == 64) + afi_ss1_val = AFIFS_SS1_BUS_WIDTH_64_CONFIG_VAL; + else if (bus_width == 128) + afi_ss1_val = AFIFS_SS1_BUS_WIDTH_128_CONFIG_VAL; + else + return -EINVAL; + + ret = zynqmp_pm_afi(AFIFS, afi_ss1_val | afi_ss0_val); + } + } else { + if (bus_width == 32) + ret = zynqmp_pm_afi(cfgptr->id, + AFIFM_BUS_WIDTH_32_CONFIG_VAL); + else if (bus_width == 64) + ret = zynqmp_pm_afi(cfgptr->id, + AFIFM_BUS_WIDTH_64_CONFIG_VAL); + else if (bus_width == 128) + ret = zynqmp_pm_afi(cfgptr->id, + AFIFM_BUS_WIDTH_128_CONFIG_VAL); + else + return -EINVAL; + } + } + cfgptr++; + } + + return 0; +} + +static int zynqmp_afi_enable_set(struct fpga_bridge *bridge, bool enable) +{ + struct device_node *overlay = bridge->info->overlay; + struct zynqmp_afi *priv = bridge->priv; + int ret = 0; + + if (enable) { + reset_control_reset(priv->resets); + return 0; + } + + of_node_get(overlay); + priv->of_node = + of_find_node_with_property(overlay, + "xlnx,afi-fm0-rd-bus-width"); + if (priv->of_node) + ret = zynqmp_afi_config(priv); + of_node_put(priv->of_node); + + return ret; +} + +static const struct fpga_bridge_ops zynqmp_afi_br_ops = { + .enable_set = zynqmp_afi_enable_set, +}; + +static const struct of_device_id zynqmp_afi_of_match[] = { + { .compatible = "xlnx,zynqmp-afi-fpga" }, + { }, +}; +MODULE_DEVICE_TABLE(of, zynqmp_afi_of_match); + +static int zynqmp_afi_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct zynqmp_afi *priv; + struct fpga_bridge *br; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->dev = dev; + + priv->resets = devm_reset_control_array_get_optional_exclusive(&pdev->dev); + if (IS_ERR(priv->resets)) + return PTR_ERR(priv->resets); + + br = fpga_bridge_register(dev, "Xilinx ZynqMP AFI", + &zynqmp_afi_br_ops, priv); + if (IS_ERR(br)) { + dev_err(dev, "unable to register Xilinx ZynqMP AFI"); + return PTR_ERR(br); + } + + platform_set_drvdata(pdev, br); + + return 0; +} + +static int zynqmp_afi_remove(struct platform_device *pdev) +{ + struct fpga_bridge *bridge = platform_get_drvdata(pdev); + + fpga_bridge_unregister(bridge); + + return 0; +} + +static struct platform_driver zynqmp_afi_driver = { + .probe = zynqmp_afi_probe, + .remove = zynqmp_afi_remove, + .driver = { + .name = "zynqmp_afi", + .of_match_table = of_match_ptr(zynqmp_afi_of_match), + }, +}; + +module_platform_driver(zynqmp_afi_driver); + +MODULE_DESCRIPTION("ZYNQMP FPGA AXI FIFO interface configuration module"); +MODULE_AUTHOR("Nava kishore Manne <nava.kishore.manne@amd.com>"); +MODULE_LICENSE("GPL");
Add zynqmp AXI FIFO interface(AFI) config driver. This is useful for the configuration of the PS-PL interface on Zynq US+ MPSoC platform. Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com> --- MAINTAINERS | 6 ++ drivers/fpga/Kconfig | 13 +++ drivers/fpga/Makefile | 1 + drivers/fpga/zynqmp-afi.c | 211 ++++++++++++++++++++++++++++++++++++++ 4 files changed, 231 insertions(+) create mode 100644 drivers/fpga/zynqmp-afi.c