| Message ID | 20220804194705.459670-1-sean.anderson@seco.com (mailing list archive) |
|---|---|
| Headers | show |
| Series | net: dpaa: Convert to phylink | expand |
On 8/4/22 3:46 PM, Sean Anderson wrote: > This series converts the DPAA driver to phylink. > > I have tried to maintain backwards compatibility with existing device > trees whereever possible. However, one area where I was unable to > achieve this was with QSGMII. Please refer to patch 2 for details. > > All mac drivers have now been converted. I would greatly appreciate if > anyone has T-series or P-series boards they can test/debug this series > on. I only have an LS1046ARDB. Everything but QSGMII should work without > breakage; QSGMII needs patches 7 and 8. For this reason, the last 4 > patches in this series should be applied together (and should not go > through separate trees). > > This series depends on [1] and [2]. > > [1] https://lore.kernel.org/netdev/20220725153730.2604096-1-sean.anderson@seco.com/ > [2] https://lore.kernel.org/netdev/20220725151039.2581576-1-sean.anderson@seco.com/ > > Changes in v4: > - Use pcs-handle-names instead of pcs-names, as discussed > - Don't fail if phy support was not compiled in > - Split off rate adaptation series > - Split off DPAA "preparation" series > - Split off Lynx 10G support > - t208x: Mark MAC1 and MAC2 as 10G > - Add XFI PCS for t208x MAC1/MAC2 > > Changes in v3: > - Expand pcs-handle to an array > - Add vendor prefix 'fsl,' to rgmii and mii properties. > - Set maxItems for pcs-names > - Remove phy-* properties from example because dt-schema complains and I > can't be bothered to figure out how to make it work. > - Add pcs-handle as a preferred version of pcsphy-handle > - Deprecate pcsphy-handle > - Remove mii/rmii properties > - Put the PCS mdiodev only after we are done with it (since the PCS > does not perform a get itself). > - Remove _return label from memac_initialization in favor of returning > directly > - Fix grabbing the default PCS not checking for -ENODATA from > of_property_match_string > - Set DTSEC_ECNTRL_R100M in dtsec_link_up instead of dtsec_mac_config > - Remove rmii/mii properties > - Replace 1000Base... with 1000BASE... to match IEEE capitalization > - Add compatibles for QSGMII PCSs > - Split arm and powerpcs dts updates > > Changes in v2: > - Better document how we select which PCS to use in the default case > - Move PCS_LYNX dependency to fman Kconfig > - Remove unused variable slow_10g_if > - Restrict valid link modes based on the phy interface. This is easier > to set up, and mostly captures what I intended to do the first time. > We now have a custom validate which restricts half-duplex for some SoCs > for RGMII, but generally just uses the default phylink validate. > - Configure the SerDes in enable/disable > - Properly implement all ethtool ops and ioctls. These were mostly > stubbed out just enough to compile last time. > - Convert 10GEC and dTSEC as well > - Fix capitalization of mEMAC in commit messages > - Add nodes for QSGMII PCSs > - Add nodes for QSGMII PCSs > > Sean Anderson (8): > dt-bindings: net: Expand pcs-handle to an array > dt-bindings: net: fman: Add additional interface properties > net: fman: memac: Add serdes support > net: fman: memac: Use lynx pcs driver > net: dpaa: Convert to phylink > powerpc: dts: t208x: Mark MAC1 and MAC2 as 10G > powerpc: dts: qoriq: Add nodes for QSGMII PCSs > arm64: dts: layerscape: Add nodes for QSGMII PCSs > > .../bindings/net/dsa/renesas,rzn1-a5psw.yaml | 1 + > .../bindings/net/ethernet-controller.yaml | 10 +- > .../bindings/net/fsl,fman-dtsec.yaml | 53 +- > .../bindings/net/fsl,qoriq-mc-dpmac.yaml | 2 +- > .../devicetree/bindings/net/fsl-fman.txt | 5 +- > .../boot/dts/freescale/fsl-ls1043-post.dtsi | 24 + > .../boot/dts/freescale/fsl-ls1046-post.dtsi | 25 + > .../fsl/qoriq-fman3-0-10g-0-best-effort.dtsi | 3 +- > .../boot/dts/fsl/qoriq-fman3-0-10g-0.dtsi | 10 +- > .../fsl/qoriq-fman3-0-10g-1-best-effort.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-0-10g-1.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi | 45 ++ > .../boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi | 45 ++ > .../boot/dts/fsl/qoriq-fman3-0-1g-0.dtsi | 3 +- > .../boot/dts/fsl/qoriq-fman3-0-1g-1.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-0-1g-2.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-0-1g-3.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-0-1g-4.dtsi | 3 +- > .../boot/dts/fsl/qoriq-fman3-0-1g-5.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-1-10g-0.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-1-10g-1.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-1-1g-0.dtsi | 3 +- > .../boot/dts/fsl/qoriq-fman3-1-1g-1.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-1-1g-2.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-1-1g-3.dtsi | 10 +- > .../boot/dts/fsl/qoriq-fman3-1-1g-4.dtsi | 3 +- > .../boot/dts/fsl/qoriq-fman3-1-1g-5.dtsi | 10 +- > arch/powerpc/boot/dts/fsl/t2081si-post.dtsi | 4 +- > drivers/net/ethernet/freescale/dpaa/Kconfig | 4 +- > .../net/ethernet/freescale/dpaa/dpaa_eth.c | 89 +-- > .../ethernet/freescale/dpaa/dpaa_ethtool.c | 90 +-- > drivers/net/ethernet/freescale/fman/Kconfig | 4 +- > .../net/ethernet/freescale/fman/fman_dtsec.c | 459 +++++------ > .../net/ethernet/freescale/fman/fman_mac.h | 10 - > .../net/ethernet/freescale/fman/fman_memac.c | 746 +++++++++--------- > .../net/ethernet/freescale/fman/fman_tgec.c | 131 ++- > drivers/net/ethernet/freescale/fman/mac.c | 168 +--- > drivers/net/ethernet/freescale/fman/mac.h | 23 +- > 38 files changed, 1033 insertions(+), 1050 deletions(-) > create mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-2.dtsi > create mode 100644 arch/powerpc/boot/dts/fsl/qoriq-fman3-0-10g-3.dtsi > ping? This will not apply on net-next/master, so I will resend sometime soon, but does anyone have any feedback first? --Sean