| Message ID | 20220908184925.2714098-3-sireeshkodali1@gmail.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | remoteproc: qcom: Add support for pronto-v3 | expand |
On Fri, 09 Sep 2022 00:19:23 +0530, Sireesh Kodali wrote: > This is a direct conversion of the existing txt documentation to YAML. > It is in preparation for the addition of pronto-v3 to the docs. This > patch doesn't document any of the existing subnodes/properties that are > not documented in the existing txt file. That is done in a separate > patch. > > Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com> > --- > .../bindings/remoteproc/qcom,wcnss-pil.yaml | 263 ++++++++++++++++++ > 1 file changed, 263 insertions(+) > create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddxo-supply' is a required property From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddrfa-supply' is a required property From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddpa-supply' is a required property From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vdddig-supply' is a required property From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: wcnss: 'bt' does not match any of the regexes: 'pinctrl-[0-9]+' From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.yaml doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/patch/ This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit.
On 08/09/2022 20:49, Sireesh Kodali wrote: > This is a direct conversion of the existing txt documentation to YAML. > It is in preparation for the addition of pronto-v3 to the docs. This > patch doesn't document any of the existing subnodes/properties that are > not documented in the existing txt file. That is done in a separate > patch. There is no conversion here... Just adding new bindings. Best regards, Krzysztof
On 08/09/2022 20:49, Sireesh Kodali wrote: > This is a direct conversion of the existing txt documentation to YAML. > It is in preparation for the addition of pronto-v3 to the docs. This > patch doesn't document any of the existing subnodes/properties that are > not documented in the existing txt file. That is done in a separate > patch. > > Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com> > --- > .../bindings/remoteproc/qcom,wcnss-pil.yaml | 263 ++++++++++++++++++ > 1 file changed, 263 insertions(+) > create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > > diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > new file mode 100644 > index 000000000000..bc18139fdb91 > --- /dev/null > +++ b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > @@ -0,0 +1,263 @@ > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/remoteproc/qcom,wcnss-pil.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm WCNSS Peripheral Image Loader > + > +maintainers: > + - Bjorn Andersson <bjorn.andersson@linaro.org> Use email from maintainers entry. > + > +description: > + This document defines the binding for a component that loads and boots > + firmware on the Qualcomm WCNSS core. > + > +properties: > + compatible: > + enum: > + - qcom,riva-pil > + - qcom,pronto-v1-pil > + - qcom,pronto-v2-pil > + > + reg: > + maxItems: 3 > + description: > + The base address and size of the CCU, DXE and PMU register blocks > + > + reg-names: > + items: > + - const: ccu > + - const: dxe > + - const: pmu > + > + interrupts: > + minItems: 2 > + maxItems: 5 > + > + interrupt-names: > + minItems: 2 > + items: > + - const: wdog > + - const: fatal > + - const: ready > + - const: handover > + - const: stop-ack > + > + firmware-name: > + $ref: /schemas/types.yaml#/definitions/string > + description: > + Relative firmware image path for the WCNSS core. Defaults to > + "wcnss.mdt". > + > + vddpx-supply: > + description: > + PX regulator to be held on behalf of the booting of the WCNSS core > + > + vddmx-supply: > + description: > + MX regulator to be held on behalf of the booting of the WCNSS core. > + > + vddcx-supply: > + description: > + CX regulator to be held on behalf of the booting of the WCNSS core. > + > + power-domains: > + maxItems: 2 > + > + power-domain-names: > + items: > + - const: cx > + - const: mx > + > + qcom,smem-states: > + $ref: /schemas/types.yaml#/definitions/phandle-array > + description: > + States used by the AP to signal the WCNSS core that it should shutdown > + items: > + - description: Stop the modem > + > + qcom,smem-state-names: > + description: The names of the state bits used for SMP2P output > + items: > + - const: stop > + > + memory-region: > + maxItems: 1 > + description: reserved-memory for the WCNSS core > + > + smd-edge: > + $ref: /schemas/remoteproc/qcom,smd-edge.yaml# > + description: > + Qualcomm Shared Memory subnode which represents communication edge, > + channels and devices related to the ADSP. > + > + iris: > + type: object > + description: > + The iris subnode of the WCNSS PIL is used to describe the attached RF module > + and its resource dependencies. > + additionalProperties false on this level. > + properties: > + compatible: > + enum: > + - qcom,wcn3620 > + - qcom,wcn3660 > + - qcom,wcn3660b > + - qcom,wcn3680 > + > + clocks: > + minItems: 1 > + items: > + - description: XO clock > + - description: RF clock > + > + clock-names: > + minItems: 1 > + items: > + - const: xo > + - const: rf > + > + vddxo-supply: > + description: > + Reference to the regulator to be held on behalf of the booting WCNSS > + core > + > + vddrfa-supply: > + description: > + Reference to the regulator to be held on behalf of the booting WCNSS > + core > + > + vddpa-supply: > + description: > + Reference to the regulator to be held on behalf of the booting WCNSS > + core > + > + vdddig-supply: Best regards, Krzysztof
On 08/09/2022 23:16, Rob Herring wrote: > On Fri, 09 Sep 2022 00:19:23 +0530, Sireesh Kodali wrote: >> This is a direct conversion of the existing txt documentation to YAML. >> It is in preparation for the addition of pronto-v3 to the docs. This >> patch doesn't document any of the existing subnodes/properties that are >> not documented in the existing txt file. That is done in a separate >> patch. >> >> Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com> >> --- >> .../bindings/remoteproc/qcom,wcnss-pil.yaml | 263 ++++++++++++++++++ >> 1 file changed, 263 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml >> > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddxo-supply' is a required property > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddrfa-supply' is a required property > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddpa-supply' is a required property > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vdddig-supply' is a required property > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: wcnss: 'bt' does not match any of the regexes: 'pinctrl-[0-9]+' > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.yaml > This needs to be fixed. Please run `make dt_binding_check` (see Documentation/devicetree/bindings/writing-schema.rst for instructions). Best regards, Krzysztof
On Fri Sep 9, 2022 at 1:27 PM IST, Krzysztof Kozlowski wrote: > On 08/09/2022 20:49, Sireesh Kodali wrote: > > This is a direct conversion of the existing txt documentation to YAML. > > It is in preparation for the addition of pronto-v3 to the docs. This > > patch doesn't document any of the existing subnodes/properties that are > > not documented in the existing txt file. That is done in a separate > > patch. > > There is no conversion here... Just adding new bindings. My mistake, will be fixed in v3 Thanks, Sireesh > > Best regards, > Krzysztof
On Fri Sep 9, 2022 at 1:30 PM IST, Krzysztof Kozlowski wrote: > On 08/09/2022 23:16, Rob Herring wrote: > > On Fri, 09 Sep 2022 00:19:23 +0530, Sireesh Kodali wrote: > >> This is a direct conversion of the existing txt documentation to YAML. > >> It is in preparation for the addition of pronto-v3 to the docs. This > >> patch doesn't document any of the existing subnodes/properties that are > >> not documented in the existing txt file. That is done in a separate > >> patch. > >> > >> Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com> > >> --- > >> .../bindings/remoteproc/qcom,wcnss-pil.yaml | 263 ++++++++++++++++++ > >> 1 file changed, 263 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > >> > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > > > yamllint warnings/errors: > > > > dtschema/dtc warnings/errors: > > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddxo-supply' is a required property > > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddrfa-supply' is a required property > > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vddpa-supply' is a required property > > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: pronto@a21b000: iris: 'vdddig-supply' is a required property > > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.example.dtb: wcnss: 'bt' does not match any of the regexes: 'pinctrl-[0-9]+' > > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/soc/qcom/qcom,wcnss.yaml > > > > This needs to be fixed. > > Please run `make dt_binding_check` (see > Documentation/devicetree/bindings/writing-schema.rst for instructions). > Will be fixed in v3 Regards, Sireesh > > Best regards, > Krzysztof
On Fri Sep 9, 2022 at 1:29 PM IST, Krzysztof Kozlowski wrote: > On 08/09/2022 20:49, Sireesh Kodali wrote: > > This is a direct conversion of the existing txt documentation to YAML. > > It is in preparation for the addition of pronto-v3 to the docs. This > > patch doesn't document any of the existing subnodes/properties that are > > not documented in the existing txt file. That is done in a separate > > patch. > > > > Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com> > > --- > > .../bindings/remoteproc/qcom,wcnss-pil.yaml | 263 ++++++++++++++++++ > > 1 file changed, 263 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > > > > diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > > new file mode 100644 > > index 000000000000..bc18139fdb91 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml > > @@ -0,0 +1,263 @@ > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/remoteproc/qcom,wcnss-pil.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Qualcomm WCNSS Peripheral Image Loader > > + > > +maintainers: > > + - Bjorn Andersson <bjorn.andersson@linaro.org> > > Use email from maintainers entry. I didn't notice the entry had changed from since v1, will be fixed in v3 > > > + > > +description: > > + This document defines the binding for a component that loads and boots > > + firmware on the Qualcomm WCNSS core. > > + > > +properties: > > + compatible: > > + enum: > > + - qcom,riva-pil > > + - qcom,pronto-v1-pil > > + - qcom,pronto-v2-pil > > + > > + reg: > > + maxItems: 3 > > + description: > > + The base address and size of the CCU, DXE and PMU register blocks > > + > > + reg-names: > > + items: > > + - const: ccu > > + - const: dxe > > + - const: pmu > > + > > + interrupts: > > + minItems: 2 > > + maxItems: 5 > > + > > + interrupt-names: > > + minItems: 2 > > + items: > > + - const: wdog > > + - const: fatal > > + - const: ready > > + - const: handover > > + - const: stop-ack > > + > > + firmware-name: > > + $ref: /schemas/types.yaml#/definitions/string > > + description: > > + Relative firmware image path for the WCNSS core. Defaults to > > + "wcnss.mdt". > > + > > + vddpx-supply: > > + description: > > + PX regulator to be held on behalf of the booting of the WCNSS core > > + > > + vddmx-supply: > > + description: > > + MX regulator to be held on behalf of the booting of the WCNSS core. > > + > > + vddcx-supply: > > + description: > > + CX regulator to be held on behalf of the booting of the WCNSS core. > > + > > + power-domains: > > + maxItems: 2 > > + > > + power-domain-names: > > + items: > > + - const: cx > > + - const: mx > > + > > + qcom,smem-states: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + description: > > + States used by the AP to signal the WCNSS core that it should shutdown > > + items: > > + - description: Stop the modem > > + > > + qcom,smem-state-names: > > + description: The names of the state bits used for SMP2P output > > + items: > > + - const: stop > > + > > + memory-region: > > + maxItems: 1 > > + description: reserved-memory for the WCNSS core > > + > > + smd-edge: > > + $ref: /schemas/remoteproc/qcom,smd-edge.yaml# > > + description: > > + Qualcomm Shared Memory subnode which represents communication edge, > > + channels and devices related to the ADSP. > > + > > + iris: > > + type: object > > + description: > > + The iris subnode of the WCNSS PIL is used to describe the attached RF module > > + and its resource dependencies. > > + > additionalProperties false on this level. Will be added in v3 Regards, Sireesh > > > + properties: > > + compatible: > > + enum: > > + - qcom,wcn3620 > > + - qcom,wcn3660 > > + - qcom,wcn3660b > > + - qcom,wcn3680 > > + > > + clocks: > > + minItems: 1 > > + items: > > + - description: XO clock > > + - description: RF clock > > + > > + clock-names: > > + minItems: 1 > > + items: > > + - const: xo > > + - const: rf > > + > > + vddxo-supply: > > + description: > > + Reference to the regulator to be held on behalf of the booting WCNSS > > + core > > + > > + vddrfa-supply: > > + description: > > + Reference to the regulator to be held on behalf of the booting WCNSS > > + core > > + > > + vddpa-supply: > > + description: > > + Reference to the regulator to be held on behalf of the booting WCNSS > > + core > > + > > + vdddig-supply: > > Best regards, > Krzysztof
diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml new file mode 100644 index 000000000000..bc18139fdb91 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml @@ -0,0 +1,263 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/remoteproc/qcom,wcnss-pil.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm WCNSS Peripheral Image Loader + +maintainers: + - Bjorn Andersson <bjorn.andersson@linaro.org> + +description: + This document defines the binding for a component that loads and boots + firmware on the Qualcomm WCNSS core. + +properties: + compatible: + enum: + - qcom,riva-pil + - qcom,pronto-v1-pil + - qcom,pronto-v2-pil + + reg: + maxItems: 3 + description: + The base address and size of the CCU, DXE and PMU register blocks + + reg-names: + items: + - const: ccu + - const: dxe + - const: pmu + + interrupts: + minItems: 2 + maxItems: 5 + + interrupt-names: + minItems: 2 + items: + - const: wdog + - const: fatal + - const: ready + - const: handover + - const: stop-ack + + firmware-name: + $ref: /schemas/types.yaml#/definitions/string + description: + Relative firmware image path for the WCNSS core. Defaults to + "wcnss.mdt". + + vddpx-supply: + description: + PX regulator to be held on behalf of the booting of the WCNSS core + + vddmx-supply: + description: + MX regulator to be held on behalf of the booting of the WCNSS core. + + vddcx-supply: + description: + CX regulator to be held on behalf of the booting of the WCNSS core. + + power-domains: + maxItems: 2 + + power-domain-names: + items: + - const: cx + - const: mx + + qcom,smem-states: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + States used by the AP to signal the WCNSS core that it should shutdown + items: + - description: Stop the modem + + qcom,smem-state-names: + description: The names of the state bits used for SMP2P output + items: + - const: stop + + memory-region: + maxItems: 1 + description: reserved-memory for the WCNSS core + + smd-edge: + $ref: /schemas/remoteproc/qcom,smd-edge.yaml# + description: + Qualcomm Shared Memory subnode which represents communication edge, + channels and devices related to the ADSP. + + iris: + type: object + description: + The iris subnode of the WCNSS PIL is used to describe the attached RF module + and its resource dependencies. + + properties: + compatible: + enum: + - qcom,wcn3620 + - qcom,wcn3660 + - qcom,wcn3660b + - qcom,wcn3680 + + clocks: + minItems: 1 + items: + - description: XO clock + - description: RF clock + + clock-names: + minItems: 1 + items: + - const: xo + - const: rf + + vddxo-supply: + description: + Reference to the regulator to be held on behalf of the booting WCNSS + core + + vddrfa-supply: + description: + Reference to the regulator to be held on behalf of the booting WCNSS + core + + vddpa-supply: + description: + Reference to the regulator to be held on behalf of the booting WCNSS + core + + vdddig-supply: + description: + Reference to the regulator to be held on behalf of the booting WCNSS + core + + required: + - compatible + - clocks + - clock-names + - vddxo-supply + - vddrfa-supply + - vddpa-supply + - vdddig-supply + +required: + - compatible + - reg + - reg-names + - interrupts-extended + - interrupt-names + - iris + - vddpx-supply + - memory-region + - smd-edge + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + const: qcom,riva-pil + then: + required: + - vddcx-supply + - vddmx-supply + + - if: + properties: + compatible: + contains: + enum: + - qcom,pronto-v1-pil + - qcom,pronto-v2-pil + then: + properties: + vddmx-supply: + deprecated: true + description: Deprecated for qcom,pronto-v1/2-pil + + vddcx-supply: + deprecated: true + description: Deprecated for qcom,pronto-v1/2-pil + + required: + - power-domains + - power-domain-names + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/qcom,rpmcc.h> + #include <dt-bindings/power/qcom-rpmpd.h> + pronto@a21b000 { + compatible = "qcom,pronto-v2-pil"; + reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>; + reg-names = "ccu", "dxe", "pmu"; + + interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>, + <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack"; + + power-domains = <&rpmpd MSM8916_VDDCX>, <&rpmpd MSM8916_VDDMX>; + power-domain-names = "cx", "mx"; + + vddpx-supply = <&pm8916_l7>; + + qcom,smem-states = <&wcnss_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + memory-region = <&wcnss_region>; + + pinctrl-names = "default"; + pinctrl-0 = <&wcnss_pin_a>; + + iris { + compatible = "qcom,wcn3620"; + + clocks = <&rpmcc RPM_SMD_RF_CLK2>; + clock-names = "xo"; + }; + + smd-edge { + interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>; + + qcom,ipc = <&apcs 8 17>; + qcom,smd-edge = <6>; + qcom,remote-pid = <4>; + + label = "pronto"; + + wcnss { + compatible = "qcom,wcnss"; + qcom,smd-channels = "WCNSS_CTRL"; + + qcom,mmio = <&pronto>; + + bt { + compatible = "qcom,wcnss-bt"; + }; + + wifi { + compatible = "qcom,wcnss-wlan"; + + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx", "rx"; + + qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>; + qcom,smem-state-names = "tx-enable", "tx-rings-empty"; + }; + }; + }; + };
This is a direct conversion of the existing txt documentation to YAML. It is in preparation for the addition of pronto-v3 to the docs. This patch doesn't document any of the existing subnodes/properties that are not documented in the existing txt file. That is done in a separate patch. Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com> --- .../bindings/remoteproc/qcom,wcnss-pil.yaml | 263 ++++++++++++++++++ 1 file changed, 263 insertions(+) create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,wcnss-pil.yaml