deleted file mode 100644
@@ -1,283 +0,0 @@
-Qualcomm Resource Power Manager (RPM)
-
-This driver is used to interface with the Resource Power Manager (RPM) found in
-various Qualcomm platforms. The RPM allows each component in the system to vote
-for state of the system resources, such as clocks, regulators and bus
-frequencies.
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be one of:
- "qcom,rpm-apq8064"
- "qcom,rpm-msm8660"
- "qcom,rpm-msm8960"
- "qcom,rpm-ipq8064"
- "qcom,rpm-mdm9615"
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: base address and size of the RPM's message ram
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: three entries specifying the RPM's:
- 1. acknowledgement interrupt
- 2. error interrupt
- 3. wakeup interrupt
-
-- interrupt-names:
- Usage: required
- Value type: <string-array>
- Definition: must be the three strings "ack", "err" and "wakeup", in order
-
-- qcom,ipc:
- Usage: required
- Value type: <prop-encoded-array>
-
- Definition: three entries specifying the outgoing ipc bit used for
- signaling the RPM:
- - phandle to a syscon node representing the apcs registers
- - u32 representing offset to the register within the syscon
- - u32 representing the ipc bit within the register
-
-
-= SUBNODES
-
-The RPM exposes resources to its subnodes. The below bindings specify the set
-of valid subnodes that can operate on these resources.
-
-== Regulators
-
-Regulator nodes are identified by their compatible:
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be one of:
- "qcom,rpm-pm8058-regulators"
- "qcom,rpm-pm8901-regulators"
- "qcom,rpm-pm8921-regulators"
- "qcom,rpm-pm8018-regulators"
- "qcom,rpm-smb208-regulators"
-
-- vdd_l0_l1_lvs-supply:
-- vdd_l2_l11_l12-supply:
-- vdd_l3_l4_l5-supply:
-- vdd_l6_l7-supply:
-- vdd_l8-supply:
-- vdd_l9-supply:
-- vdd_l10-supply:
-- vdd_l13_l16-supply:
-- vdd_l14_l15-supply:
-- vdd_l17_l18-supply:
-- vdd_l19_l20-supply:
-- vdd_l21-supply:
-- vdd_l22-supply:
-- vdd_l23_l24_l25-supply:
-- vdd_ncp-supply:
-- vdd_s0-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
- Usage: optional (pm8058 only)
- Value type: <phandle>
- Definition: reference to regulator supplying the input pin, as
- described in the data sheet
-
-- lvs0_in-supply:
-- lvs1_in-supply:
-- lvs2_in-supply:
-- lvs3_in-supply:
-- mvs_in-supply:
-- vdd_l0-supply:
-- vdd_l1-supply:
-- vdd_l2-supply:
-- vdd_l3-supply:
-- vdd_l4-supply:
-- vdd_l5-supply:
-- vdd_l6-supply:
-- vdd_s0-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
- Usage: optional (pm8901 only)
- Value type: <phandle>
- Definition: reference to regulator supplying the input pin, as
- described in the data sheet
-
-- vdd_l1_l2_l12_l18-supply:
-- vdd_l3_l15_l17-supply:
-- vdd_l4_l14-supply:
-- vdd_l5_l8_l16-supply:
-- vdd_l6_l7-supply:
-- vdd_l9_l11-supply:
-- vdd_l10_l22-supply:
-- vdd_l21_l23_l29-supply:
-- vdd_l24-supply:
-- vdd_l25-supply:
-- vdd_l26-supply:
-- vdd_l27-supply:
-- vdd_l28-supply:
-- vdd_ncp-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-- vin_5vs-supply:
-- vin_lvs1_3_6-supply:
-- vin_lvs2-supply:
-- vin_lvs4_5_7-supply:
- Usage: optional (pm8921 only)
- Value type: <phandle>
- Definition: reference to regulator supplying the input pin, as
- described in the data sheet
-
-- vin_lvs1-supply:
-- vdd_l7-supply:
-- vdd_l8-supply:
-- vdd_l9_l10_l11_l12-supply:
- Usage: optional (pm8018 only)
- Value type: <phandle>
- Definition: reference to regulator supplying the input pin, as
- described in the data sheet
-
-The regulator node houses sub-nodes for each regulator within the device. Each
-sub-node is identified using the node's name, with valid values listed for each
-of the pmics below.
-
-pm8058:
- l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
- l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
- lvs0, lvs1, ncp
-
-pm8901:
- l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
- mvs
-
-pm8921:
- s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
- l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
- l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
- ncp
-
-pm8018:
- s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
- l12, l14, lvs1
-
-smb208:
- s1a, s1b, s2a, s2b
-
-The content of each sub-node is defined by the standard binding for regulators -
-see regulator.txt - with additional custom properties described below:
-
-=== Switch-mode Power Supply regulator custom properties
-
-- bias-pull-down:
- Usage: optional
- Value type: <empty>
- Definition: enable pull down of the regulator when inactive
-
-- qcom,switch-mode-frequency:
- Usage: required
- Value type: <u32>
- Definition: Frequency (Hz) of the switch-mode power supply;
- must be one of:
- 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
- 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
- 1480000, 1370000, 1280000, 1200000
-
-- qcom,force-mode:
- Usage: optional (default if no other qcom,force-mode is specified)
- Value type: <u32>
- Definition: indicates that the regulator should be forced to a
- particular mode, valid values are:
- QCOM_RPM_FORCE_MODE_NONE - do not force any mode
- QCOM_RPM_FORCE_MODE_LPM - force into low power mode
- QCOM_RPM_FORCE_MODE_HPM - force into high power mode
- QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
- select its own mode based on
- realtime current draw, only for:
- pm8921 smps and ftsmps
-
-- qcom,power-mode-hysteretic:
- Usage: optional
- Value type: <empty>
- Definition: select that the power supply should operate in hysteretic
- mode, instead of the default pwm mode
-
-=== Low-dropout regulator custom properties
-
-- bias-pull-down:
- Usage: optional
- Value type: <empty>
- Definition: enable pull down of the regulator when inactive
-
-- qcom,force-mode:
- Usage: optional
- Value type: <u32>
- Definition: indicates that the regulator should not be forced to any
- particular mode, valid values are:
- QCOM_RPM_FORCE_MODE_NONE - do not force any mode
- QCOM_RPM_FORCE_MODE_LPM - force into low power mode
- QCOM_RPM_FORCE_MODE_HPM - force into high power mode
- QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
- mode, i.e. to act as a switch
- and not regulate, only for:
- pm8921 pldo, nldo and nldo1200
-
-=== Negative Charge Pump custom properties
-
-- qcom,switch-mode-frequency:
- Usage: required
- Value type: <u32>
- Definition: Frequency (Hz) of the switch mode power supply;
- must be one of:
- 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
- 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
- 1480000, 1370000, 1280000, 1200000
-
-= EXAMPLE
-
- #include <dt-bindings/mfd/qcom-rpm.h>
-
- rpm@108000 {
- compatible = "qcom,rpm-msm8960";
- reg = <0x108000 0x1000>;
- qcom,ipc = <&apcs 0x8 2>;
-
- interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
- interrupt-names = "ack", "err", "wakeup";
-
- regulators {
- compatible = "qcom,rpm-pm8921-regulators";
- vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-
- s1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- bias-pull-down;
-
- qcom,switch-mode-frequency = <3200000>;
- };
-
- pm8921_s4: s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
-
- qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
- };
- };
- };
-
new file mode 100644
@@ -0,0 +1,99 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/soc/qcom/qcom,ipc-rpm.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Resource Power Manager (RPM) over IPC
+
+description: |
+ This driver is used to interface with the Resource Power Manager (RPM) found
+ in various Qualcomm platforms. The RPM allows each component in the system
+ to vote for state of the system resources, such as clocks, regulators and bus
+ frequencies.
+
+maintainers:
+ - Bjorn Andersson <andersson@kernel.org>
+
+properties:
+ compatible:
+ enum:
+ - qcom,rpm-apq8064
+ - qcom,rpm-msm8660
+ - qcom,rpm-msm8960
+ - qcom,rpm-ipq8064
+ - qcom,rpm-mdm9615
+
+ reg: true
+
+ interrupts:
+ minItems: 3
+
+ interrupt-names:
+ items:
+ - const: ack
+ - const: err
+ - const: wakeup
+
+ qcom,ipc:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ items:
+ - items:
+ - description: phandle to a syscon node representing the APCS registers
+ - description: u32 representing offset to the register within the syscon
+ - description: u32 representing the ipc bit within the register
+ description:
+ Three entries specifying the outgoing ipc bit used for signaling the RPM.
+
+patternProperties:
+ "(regulators|-regulators)$":
+ type: object
+ $ref: /schemas/regulator/qcom,ipc-rpm-regulator.yaml#
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - interrupt-names
+ - qcom,ipc
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/mfd/qcom-rpm.h>
+
+ rpm@108000 {
+ compatible = "qcom,rpm-msm8960";
+ reg = <0x108000 0x1000>;
+ qcom,ipc = <&apcs 0x8 2>;
+
+ interrupts = <GIC_SPI 19 IRQ_TYPE_NONE>, <GIC_SPI 21 IRQ_TYPE_NONE>, <GIC_SPI 22 IRQ_TYPE_NONE>;
+ interrupt-names = "ack", "err", "wakeup";
+
+ regulators {
+ compatible = "qcom,rpm-pm8921-regulators";
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+
+ s1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ bias-pull-down;
+
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ pm8921_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ };
+ };
+ };
Convert the non-SMD RPM node bindings to dt-schema, the old txt bindings are now removed since all bindings were converted. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 283 --------------------- .../devicetree/bindings/soc/qcom/qcom,ipc-rpm.yaml | 99 +++++++ 2 files changed, 99 insertions(+), 283 deletions(-)