| Message ID | 20221014183459.181567-3-prabhakar.mahadev-lad.rj@bp.renesas.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | media: i2c: ov5645 driver enhancements | expand |
Hi Prabhakar, On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > Switch to using runtime PM for power management. > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > --- > v1->v2 > * Moved pm_runtime_*_autosuspend() calls after registering the subdev. > --- > drivers/media/i2c/Kconfig | 2 +- > drivers/media/i2c/ov5645.c | 137 +++++++++++++++++++------------------ > 2 files changed, 70 insertions(+), 69 deletions(-) > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > index 7806d4b81716..c0edd1017fe8 100644 > --- a/drivers/media/i2c/Kconfig > +++ b/drivers/media/i2c/Kconfig > @@ -459,7 +459,7 @@ config VIDEO_OV5640 > config VIDEO_OV5645 > tristate "OmniVision OV5645 sensor support" > depends on OF > - depends on I2C && VIDEO_DEV > + depends on I2C && PM && VIDEO_DEV > select MEDIA_CONTROLLER > select VIDEO_V4L2_SUBDEV_API > select V4L2_FWNODE > diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c > index 81e4e87e1821..1551690a94e0 100644 > --- a/drivers/media/i2c/ov5645.c > +++ b/drivers/media/i2c/ov5645.c > @@ -27,6 +27,7 @@ > #include <linux/module.h> > #include <linux/of.h> > #include <linux/of_graph.h> > +#include <linux/pm_runtime.h> > #include <linux/regulator/consumer.h> > #include <linux/slab.h> > #include <linux/types.h> > @@ -108,7 +109,6 @@ struct ov5645 { > u8 timing_tc_reg21; > > struct mutex power_lock; /* lock to protect power state */ > - int power_count; > > struct gpio_desc *enable_gpio; > struct gpio_desc *rst_gpio; > @@ -635,8 +635,24 @@ static int ov5645_set_register_array(struct ov5645 *ov5645, > return 0; > } > > -static int ov5645_set_power_on(struct ov5645 *ov5645) > +static int ov5645_set_power_off(struct device *dev) > { > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > + struct ov5645 *ov5645 = to_ov5645(sd); > + > + ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); > + gpiod_set_value_cansleep(ov5645->rst_gpio, 1); > + gpiod_set_value_cansleep(ov5645->enable_gpio, 0); > + clk_disable_unprepare(ov5645->xclk); > + regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); > + > + return 0; > +} > + > +static int ov5645_set_power_on(struct device *dev) > +{ > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > + struct ov5645 *ov5645 = to_ov5645(sd); > int ret; > > ret = regulator_bulk_enable(OV5645_NUM_SUPPLIES, ov5645->supplies); > @@ -658,57 +674,19 @@ static int ov5645_set_power_on(struct ov5645 *ov5645) > > msleep(20); > > - return 0; > -} > - > -static void ov5645_set_power_off(struct ov5645 *ov5645) > -{ > - gpiod_set_value_cansleep(ov5645->rst_gpio, 1); > - gpiod_set_value_cansleep(ov5645->enable_gpio, 0); > - clk_disable_unprepare(ov5645->xclk); > - regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); > -} > - > -static int ov5645_s_power(struct v4l2_subdev *sd, int on) > -{ > - struct ov5645 *ov5645 = to_ov5645(sd); > - int ret = 0; > - > - mutex_lock(&ov5645->power_lock); > - > - /* If the power count is modified from 0 to != 0 or from != 0 to 0, > - * update the power state. > - */ > - if (ov5645->power_count == !on) { > - if (on) { > - ret = ov5645_set_power_on(ov5645); > - if (ret < 0) > - goto exit; > - > - ret = ov5645_set_register_array(ov5645, > - ov5645_global_init_setting, > + ret = ov5645_set_register_array(ov5645, ov5645_global_init_setting, > ARRAY_SIZE(ov5645_global_init_setting)); > - if (ret < 0) { > - dev_err(ov5645->dev, > - "could not set init registers\n"); > - ov5645_set_power_off(ov5645); > - goto exit; > - } > - > - usleep_range(500, 1000); > - } else { > - ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); > - ov5645_set_power_off(ov5645); > - } > + if (ret < 0) { > + dev_err(ov5645->dev, "could not set init registers\n"); > + goto exit; > } > > - /* Update the power count. */ > - ov5645->power_count += on ? 1 : -1; > - WARN_ON(ov5645->power_count < 0); > + usleep_range(500, 1000); > > -exit: > - mutex_unlock(&ov5645->power_lock); > + return 0; > > +exit: > + ov5645_set_power_off(dev); > return ret; > } > > @@ -795,7 +773,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > int ret; > > mutex_lock(&ov5645->power_lock); > - if (!ov5645->power_count) { > + if (!pm_runtime_get_if_in_use(ov5645->dev)) { > mutex_unlock(&ov5645->power_lock); > return 0; > } > @@ -827,6 +805,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > break; > } > > + pm_runtime_put_autosuspend(ov5645->dev); I think you'll need pm_runtime_mark_last_busy() before this. I missed this on the last round. Maybe in probe() too. Feel free to resend just this patch. > mutex_unlock(&ov5645->power_lock); > > return ret; > @@ -991,6 +970,10 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > int ret; > > if (enable) { > + ret = pm_runtime_resume_and_get(ov5645->dev); > + if (ret < 0) > + return ret; > + > ret = ov5645_set_register_array(ov5645, > ov5645->current_mode->data, > ov5645->current_mode->data_size); > @@ -998,22 +981,22 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > dev_err(ov5645->dev, "could not set mode %dx%d\n", > ov5645->current_mode->width, > ov5645->current_mode->height); > - return ret; > + goto err_rpm_put; > } > ret = v4l2_ctrl_handler_setup(&ov5645->ctrls); > if (ret < 0) { > dev_err(ov5645->dev, "could not sync v4l2 controls\n"); > - return ret; > + goto err_rpm_put; > } > > ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45); > if (ret < 0) > - return ret; > + goto err_rpm_put; > > ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0, > OV5645_SYSTEM_CTRL0_START); > if (ret < 0) > - return ret; > + goto err_rpm_put; > } else { > ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40); > if (ret < 0) > @@ -1023,14 +1006,15 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > OV5645_SYSTEM_CTRL0_STOP); > if (ret < 0) > return ret; > + pm_runtime_put(ov5645->dev); > } > > return 0; > -} > > -static const struct v4l2_subdev_core_ops ov5645_core_ops = { > - .s_power = ov5645_s_power, > -}; > +err_rpm_put: > + pm_runtime_put(ov5645->dev); > + return ret; > +} > > static const struct v4l2_subdev_video_ops ov5645_video_ops = { > .s_stream = ov5645_s_stream, > @@ -1046,7 +1030,6 @@ static const struct v4l2_subdev_pad_ops ov5645_subdev_pad_ops = { > }; > > static const struct v4l2_subdev_ops ov5645_subdev_ops = { > - .core = &ov5645_core_ops, > .video = &ov5645_video_ops, > .pad = &ov5645_subdev_pad_ops, > }; > @@ -1188,11 +1171,9 @@ static int ov5645_probe(struct i2c_client *client) > goto free_ctrl; > } > > - ret = ov5645_s_power(&ov5645->sd, true); > - if (ret < 0) { > - dev_err(dev, "could not power up OV5645\n"); > + ret = ov5645_set_power_on(dev); > + if (ret) > goto free_entity; > - } > > ret = ov5645_read_reg(ov5645, OV5645_CHIP_ID_HIGH, &chip_id_high); > if (ret < 0 || chip_id_high != OV5645_CHIP_ID_HIGH_BYTE) { > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > + pm_runtime_set_active(dev); > + pm_runtime_get_noresume(dev); > + pm_runtime_enable(dev); > + > ret = ov5645_read_reg(ov5645, OV5645_AEC_PK_MANUAL, > &ov5645->aec_pk_manual); > if (ret < 0) { > dev_err(dev, "could not read AEC/AGC mode\n"); > ret = -ENODEV; > - goto power_down; > + goto err_pm_runtime; > } > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG20, > @@ -1222,7 +1207,7 @@ static int ov5645_probe(struct i2c_client *client) > if (ret < 0) { > dev_err(dev, "could not read vflip value\n"); > ret = -ENODEV; > - goto power_down; > + goto err_pm_runtime; > } > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG21, > @@ -1230,23 +1215,30 @@ static int ov5645_probe(struct i2c_client *client) > if (ret < 0) { > dev_err(dev, "could not read hflip value\n"); > ret = -ENODEV; > - goto power_down; > + goto err_pm_runtime; > } > > - ov5645_s_power(&ov5645->sd, false); > - > ret = v4l2_async_register_subdev(&ov5645->sd); > if (ret < 0) { > dev_err(dev, "could not register v4l2 device\n"); > + pm_runtime_disable(dev); > + pm_runtime_set_suspended(dev); > goto free_entity; > } > > + pm_runtime_set_autosuspend_delay(dev, 1000); > + pm_runtime_use_autosuspend(dev); > + pm_runtime_put_autosuspend(dev); > + > ov5645_entity_init_cfg(&ov5645->sd, NULL); > > return 0; > > +err_pm_runtime: > + pm_runtime_disable(dev); > + pm_runtime_put_noidle(dev); > power_down: > - ov5645_s_power(&ov5645->sd, false); > + ov5645_set_power_off(dev); > free_entity: > media_entity_cleanup(&ov5645->sd.entity); > free_ctrl: > @@ -1264,6 +1256,10 @@ static void ov5645_remove(struct i2c_client *client) > v4l2_async_unregister_subdev(&ov5645->sd); > media_entity_cleanup(&ov5645->sd.entity); > v4l2_ctrl_handler_free(&ov5645->ctrls); > + pm_runtime_disable(ov5645->dev); > + if (!pm_runtime_status_suspended(ov5645->dev)) > + ov5645_set_power_off(ov5645->dev); > + pm_runtime_set_suspended(ov5645->dev); > mutex_destroy(&ov5645->power_lock); > } > > @@ -1279,10 +1275,15 @@ static const struct of_device_id ov5645_of_match[] = { > }; > MODULE_DEVICE_TABLE(of, ov5645_of_match); > > +static const struct dev_pm_ops ov5645_pm_ops = { > + SET_RUNTIME_PM_OPS(ov5645_set_power_off, ov5645_set_power_on, NULL) > +}; > + > static struct i2c_driver ov5645_i2c_driver = { > .driver = { > .of_match_table = ov5645_of_match, > .name = "ov5645", > + .pm = &ov5645_pm_ops, > }, > .probe_new = ov5645_probe, > .remove = ov5645_remove,
Hi Sakari, Thank you for the review. On Fri, Oct 14, 2022 at 8:18 PM Sakari Ailus <sakari.ailus@linux.intel.com> wrote: > > Hi Prabhakar, > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > > > Switch to using runtime PM for power management. > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > --- > > v1->v2 > > * Moved pm_runtime_*_autosuspend() calls after registering the subdev. > > --- <snip> > > @@ -795,7 +773,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > > int ret; > > > > mutex_lock(&ov5645->power_lock); > > - if (!ov5645->power_count) { > > + if (!pm_runtime_get_if_in_use(ov5645->dev)) { > > mutex_unlock(&ov5645->power_lock); > > return 0; > > } > > @@ -827,6 +805,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > > break; > > } > > > > + pm_runtime_put_autosuspend(ov5645->dev); > > I think you'll need pm_runtime_mark_last_busy() before this. I missed this > on the last round. Maybe in probe() too. Feel free to resend just this > patch. > Agreed, I'll respin this patch fixing the above. Cheers, Prabhakar
Hello, On Fri, Oct 14, 2022 at 07:18:11PM +0000, Sakari Ailus wrote: > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > > > Switch to using runtime PM for power management. > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > --- > > v1->v2 > > * Moved pm_runtime_*_autosuspend() calls after registering the subdev. > > --- > > drivers/media/i2c/Kconfig | 2 +- > > drivers/media/i2c/ov5645.c | 137 +++++++++++++++++++------------------ > > 2 files changed, 70 insertions(+), 69 deletions(-) > > > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > > index 7806d4b81716..c0edd1017fe8 100644 > > --- a/drivers/media/i2c/Kconfig > > +++ b/drivers/media/i2c/Kconfig > > @@ -459,7 +459,7 @@ config VIDEO_OV5640 > > config VIDEO_OV5645 > > tristate "OmniVision OV5645 sensor support" > > depends on OF > > - depends on I2C && VIDEO_DEV > > + depends on I2C && PM && VIDEO_DEV > > select MEDIA_CONTROLLER > > select VIDEO_V4L2_SUBDEV_API > > select V4L2_FWNODE > > diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c > > index 81e4e87e1821..1551690a94e0 100644 > > --- a/drivers/media/i2c/ov5645.c > > +++ b/drivers/media/i2c/ov5645.c > > @@ -27,6 +27,7 @@ > > #include <linux/module.h> > > #include <linux/of.h> > > #include <linux/of_graph.h> > > +#include <linux/pm_runtime.h> > > #include <linux/regulator/consumer.h> > > #include <linux/slab.h> > > #include <linux/types.h> > > @@ -108,7 +109,6 @@ struct ov5645 { > > u8 timing_tc_reg21; > > > > struct mutex power_lock; /* lock to protect power state */ > > - int power_count; > > > > struct gpio_desc *enable_gpio; > > struct gpio_desc *rst_gpio; > > @@ -635,8 +635,24 @@ static int ov5645_set_register_array(struct ov5645 *ov5645, > > return 0; > > } > > > > -static int ov5645_set_power_on(struct ov5645 *ov5645) > > +static int ov5645_set_power_off(struct device *dev) > > { > > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > > + struct ov5645 *ov5645 = to_ov5645(sd); > > + > > + ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); I'm not sure this belongs here, but it can be addressed later. > > + gpiod_set_value_cansleep(ov5645->rst_gpio, 1); > > + gpiod_set_value_cansleep(ov5645->enable_gpio, 0); > > + clk_disable_unprepare(ov5645->xclk); > > + regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > + > > + return 0; > > +} > > + > > +static int ov5645_set_power_on(struct device *dev) > > +{ > > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > > + struct ov5645 *ov5645 = to_ov5645(sd); > > int ret; > > > > ret = regulator_bulk_enable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > @@ -658,57 +674,19 @@ static int ov5645_set_power_on(struct ov5645 *ov5645) > > > > msleep(20); > > > > - return 0; > > -} > > - > > -static void ov5645_set_power_off(struct ov5645 *ov5645) > > -{ > > - gpiod_set_value_cansleep(ov5645->rst_gpio, 1); > > - gpiod_set_value_cansleep(ov5645->enable_gpio, 0); > > - clk_disable_unprepare(ov5645->xclk); > > - regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > -} > > - > > -static int ov5645_s_power(struct v4l2_subdev *sd, int on) > > -{ > > - struct ov5645 *ov5645 = to_ov5645(sd); > > - int ret = 0; > > - > > - mutex_lock(&ov5645->power_lock); > > - > > - /* If the power count is modified from 0 to != 0 or from != 0 to 0, > > - * update the power state. > > - */ > > - if (ov5645->power_count == !on) { > > - if (on) { > > - ret = ov5645_set_power_on(ov5645); > > - if (ret < 0) > > - goto exit; > > - > > - ret = ov5645_set_register_array(ov5645, > > - ov5645_global_init_setting, > > + ret = ov5645_set_register_array(ov5645, ov5645_global_init_setting, > > ARRAY_SIZE(ov5645_global_init_setting)); > > - if (ret < 0) { > > - dev_err(ov5645->dev, > > - "could not set init registers\n"); > > - ov5645_set_power_off(ov5645); > > - goto exit; > > - } > > - > > - usleep_range(500, 1000); > > - } else { > > - ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); > > - ov5645_set_power_off(ov5645); > > - } > > + if (ret < 0) { > > + dev_err(ov5645->dev, "could not set init registers\n"); > > + goto exit; > > } > > > > - /* Update the power count. */ > > - ov5645->power_count += on ? 1 : -1; > > - WARN_ON(ov5645->power_count < 0); > > + usleep_range(500, 1000); > > > > -exit: > > - mutex_unlock(&ov5645->power_lock); > > + return 0; > > > > +exit: > > + ov5645_set_power_off(dev); > > return ret; > > } > > > > @@ -795,7 +773,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > > int ret; > > > > mutex_lock(&ov5645->power_lock); > > - if (!ov5645->power_count) { > > + if (!pm_runtime_get_if_in_use(ov5645->dev)) { > > mutex_unlock(&ov5645->power_lock); > > return 0; > > } > > @@ -827,6 +805,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > > break; > > } > > > > + pm_runtime_put_autosuspend(ov5645->dev); > > I think you'll need pm_runtime_mark_last_busy() before this. I missed this > on the last round. Maybe in probe() too. Feel free to resend just this > patch. > > > mutex_unlock(&ov5645->power_lock); > > > > return ret; > > @@ -991,6 +970,10 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > int ret; > > > > if (enable) { > > + ret = pm_runtime_resume_and_get(ov5645->dev); > > + if (ret < 0) > > + return ret; > > + > > ret = ov5645_set_register_array(ov5645, > > ov5645->current_mode->data, > > ov5645->current_mode->data_size); > > @@ -998,22 +981,22 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > dev_err(ov5645->dev, "could not set mode %dx%d\n", > > ov5645->current_mode->width, > > ov5645->current_mode->height); > > - return ret; > > + goto err_rpm_put; > > } > > ret = v4l2_ctrl_handler_setup(&ov5645->ctrls); > > if (ret < 0) { > > dev_err(ov5645->dev, "could not sync v4l2 controls\n"); > > - return ret; > > + goto err_rpm_put; > > } > > > > ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45); > > if (ret < 0) > > - return ret; > > + goto err_rpm_put; > > > > ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0, > > OV5645_SYSTEM_CTRL0_START); > > if (ret < 0) > > - return ret; > > + goto err_rpm_put; > > } else { > > ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40); > > if (ret < 0) > > @@ -1023,14 +1006,15 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > OV5645_SYSTEM_CTRL0_STOP); > > if (ret < 0) > > return ret; > > + pm_runtime_put(ov5645->dev); > > } > > > > return 0; > > -} > > > > -static const struct v4l2_subdev_core_ops ov5645_core_ops = { > > - .s_power = ov5645_s_power, > > -}; > > +err_rpm_put: > > + pm_runtime_put(ov5645->dev); > > + return ret; > > +} > > > > static const struct v4l2_subdev_video_ops ov5645_video_ops = { > > .s_stream = ov5645_s_stream, > > @@ -1046,7 +1030,6 @@ static const struct v4l2_subdev_pad_ops ov5645_subdev_pad_ops = { > > }; > > > > static const struct v4l2_subdev_ops ov5645_subdev_ops = { > > - .core = &ov5645_core_ops, > > .video = &ov5645_video_ops, > > .pad = &ov5645_subdev_pad_ops, > > }; > > @@ -1188,11 +1171,9 @@ static int ov5645_probe(struct i2c_client *client) > > goto free_ctrl; > > } > > > > - ret = ov5645_s_power(&ov5645->sd, true); > > - if (ret < 0) { > > - dev_err(dev, "could not power up OV5645\n"); > > + ret = ov5645_set_power_on(dev); > > + if (ret) > > goto free_entity; > > - } > > > > ret = ov5645_read_reg(ov5645, OV5645_CHIP_ID_HIGH, &chip_id_high); > > if (ret < 0 || chip_id_high != OV5645_CHIP_ID_HIGH_BYTE) { > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > + pm_runtime_set_active(dev); > > + pm_runtime_get_noresume(dev); > > + pm_runtime_enable(dev); > > + > > ret = ov5645_read_reg(ov5645, OV5645_AEC_PK_MANUAL, > > &ov5645->aec_pk_manual); Totally unrelated to this patch, can we drop all these register reads ? The registers are written through he ov5645_global_init_setting array, we know what the values are. > > if (ret < 0) { > > dev_err(dev, "could not read AEC/AGC mode\n"); > > ret = -ENODEV; > > - goto power_down; > > + goto err_pm_runtime; > > } > > > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG20, > > @@ -1222,7 +1207,7 @@ static int ov5645_probe(struct i2c_client *client) > > if (ret < 0) { > > dev_err(dev, "could not read vflip value\n"); > > ret = -ENODEV; > > - goto power_down; > > + goto err_pm_runtime; > > } > > > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG21, > > @@ -1230,23 +1215,30 @@ static int ov5645_probe(struct i2c_client *client) > > if (ret < 0) { > > dev_err(dev, "could not read hflip value\n"); > > ret = -ENODEV; > > - goto power_down; > > + goto err_pm_runtime; > > } > > > > - ov5645_s_power(&ov5645->sd, false); > > - > > ret = v4l2_async_register_subdev(&ov5645->sd); > > if (ret < 0) { > > dev_err(dev, "could not register v4l2 device\n"); > > + pm_runtime_disable(dev); > > + pm_runtime_set_suspended(dev); > > goto free_entity; This looks weird, why do we need special handling of runtime PM here, instead of just jumping to err_pm_runtime ? Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > } > > > > + pm_runtime_set_autosuspend_delay(dev, 1000); > > + pm_runtime_use_autosuspend(dev); > > + pm_runtime_put_autosuspend(dev); > > + > > ov5645_entity_init_cfg(&ov5645->sd, NULL); > > > > return 0; > > > > +err_pm_runtime: > > + pm_runtime_disable(dev); > > + pm_runtime_put_noidle(dev); > > power_down: > > - ov5645_s_power(&ov5645->sd, false); > > + ov5645_set_power_off(dev); > > free_entity: > > media_entity_cleanup(&ov5645->sd.entity); > > free_ctrl: > > @@ -1264,6 +1256,10 @@ static void ov5645_remove(struct i2c_client *client) > > v4l2_async_unregister_subdev(&ov5645->sd); > > media_entity_cleanup(&ov5645->sd.entity); > > v4l2_ctrl_handler_free(&ov5645->ctrls); > > + pm_runtime_disable(ov5645->dev); > > + if (!pm_runtime_status_suspended(ov5645->dev)) > > + ov5645_set_power_off(ov5645->dev); > > + pm_runtime_set_suspended(ov5645->dev); > > mutex_destroy(&ov5645->power_lock); > > } > > > > @@ -1279,10 +1275,15 @@ static const struct of_device_id ov5645_of_match[] = { > > }; > > MODULE_DEVICE_TABLE(of, ov5645_of_match); > > > > +static const struct dev_pm_ops ov5645_pm_ops = { > > + SET_RUNTIME_PM_OPS(ov5645_set_power_off, ov5645_set_power_on, NULL) > > +}; > > + > > static struct i2c_driver ov5645_i2c_driver = { > > .driver = { > > .of_match_table = ov5645_of_match, > > .name = "ov5645", > > + .pm = &ov5645_pm_ops, > > }, > > .probe_new = ov5645_probe, > > .remove = ov5645_remove,
One more comment. On Sat, Oct 15, 2022 at 09:05:08AM +0300, Laurent Pinchart wrote: > On Fri, Oct 14, 2022 at 07:18:11PM +0000, Sakari Ailus wrote: > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > > > > > Switch to using runtime PM for power management. > > > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > > --- > > > v1->v2 > > > * Moved pm_runtime_*_autosuspend() calls after registering the subdev. > > > --- > > > drivers/media/i2c/Kconfig | 2 +- > > > drivers/media/i2c/ov5645.c | 137 +++++++++++++++++++------------------ > > > 2 files changed, 70 insertions(+), 69 deletions(-) > > > > > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > > > index 7806d4b81716..c0edd1017fe8 100644 > > > --- a/drivers/media/i2c/Kconfig > > > +++ b/drivers/media/i2c/Kconfig > > > @@ -459,7 +459,7 @@ config VIDEO_OV5640 > > > config VIDEO_OV5645 > > > tristate "OmniVision OV5645 sensor support" > > > depends on OF > > > - depends on I2C && VIDEO_DEV > > > + depends on I2C && PM && VIDEO_DEV > > > select MEDIA_CONTROLLER > > > select VIDEO_V4L2_SUBDEV_API > > > select V4L2_FWNODE > > > diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c > > > index 81e4e87e1821..1551690a94e0 100644 > > > --- a/drivers/media/i2c/ov5645.c > > > +++ b/drivers/media/i2c/ov5645.c > > > @@ -27,6 +27,7 @@ > > > #include <linux/module.h> > > > #include <linux/of.h> > > > #include <linux/of_graph.h> > > > +#include <linux/pm_runtime.h> > > > #include <linux/regulator/consumer.h> > > > #include <linux/slab.h> > > > #include <linux/types.h> > > > @@ -108,7 +109,6 @@ struct ov5645 { > > > u8 timing_tc_reg21; > > > > > > struct mutex power_lock; /* lock to protect power state */ > > > - int power_count; > > > > > > struct gpio_desc *enable_gpio; > > > struct gpio_desc *rst_gpio; > > > @@ -635,8 +635,24 @@ static int ov5645_set_register_array(struct ov5645 *ov5645, > > > return 0; > > > } > > > > > > -static int ov5645_set_power_on(struct ov5645 *ov5645) > > > +static int ov5645_set_power_off(struct device *dev) > > > { > > > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > > > + struct ov5645 *ov5645 = to_ov5645(sd); > > > + > > > + ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); > > I'm not sure this belongs here, but it can be addressed later. > > > > + gpiod_set_value_cansleep(ov5645->rst_gpio, 1); > > > + gpiod_set_value_cansleep(ov5645->enable_gpio, 0); > > > + clk_disable_unprepare(ov5645->xclk); > > > + regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > > + > > > + return 0; > > > +} > > > + > > > +static int ov5645_set_power_on(struct device *dev) > > > +{ > > > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > > > + struct ov5645 *ov5645 = to_ov5645(sd); > > > int ret; > > > > > > ret = regulator_bulk_enable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > > @@ -658,57 +674,19 @@ static int ov5645_set_power_on(struct ov5645 *ov5645) > > > > > > msleep(20); > > > > > > - return 0; > > > -} > > > - > > > -static void ov5645_set_power_off(struct ov5645 *ov5645) > > > -{ > > > - gpiod_set_value_cansleep(ov5645->rst_gpio, 1); > > > - gpiod_set_value_cansleep(ov5645->enable_gpio, 0); > > > - clk_disable_unprepare(ov5645->xclk); > > > - regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > > -} > > > - > > > -static int ov5645_s_power(struct v4l2_subdev *sd, int on) > > > -{ > > > - struct ov5645 *ov5645 = to_ov5645(sd); > > > - int ret = 0; > > > - > > > - mutex_lock(&ov5645->power_lock); > > > - > > > - /* If the power count is modified from 0 to != 0 or from != 0 to 0, > > > - * update the power state. > > > - */ > > > - if (ov5645->power_count == !on) { > > > - if (on) { > > > - ret = ov5645_set_power_on(ov5645); > > > - if (ret < 0) > > > - goto exit; > > > - > > > - ret = ov5645_set_register_array(ov5645, > > > - ov5645_global_init_setting, > > > + ret = ov5645_set_register_array(ov5645, ov5645_global_init_setting, > > > ARRAY_SIZE(ov5645_global_init_setting)); > > > - if (ret < 0) { > > > - dev_err(ov5645->dev, > > > - "could not set init registers\n"); > > > - ov5645_set_power_off(ov5645); > > > - goto exit; > > > - } > > > - > > > - usleep_range(500, 1000); > > > - } else { > > > - ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); > > > - ov5645_set_power_off(ov5645); > > > - } > > > + if (ret < 0) { > > > + dev_err(ov5645->dev, "could not set init registers\n"); > > > + goto exit; > > > } > > > > > > - /* Update the power count. */ > > > - ov5645->power_count += on ? 1 : -1; > > > - WARN_ON(ov5645->power_count < 0); > > > + usleep_range(500, 1000); > > > > > > -exit: > > > - mutex_unlock(&ov5645->power_lock); > > > + return 0; > > > > > > +exit: > > > + ov5645_set_power_off(dev); > > > return ret; > > > } > > > > > > @@ -795,7 +773,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > > > int ret; > > > > > > mutex_lock(&ov5645->power_lock); > > > - if (!ov5645->power_count) { > > > + if (!pm_runtime_get_if_in_use(ov5645->dev)) { > > > mutex_unlock(&ov5645->power_lock); > > > return 0; > > > } > > > @@ -827,6 +805,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > > > break; > > > } > > > > > > + pm_runtime_put_autosuspend(ov5645->dev); > > > > I think you'll need pm_runtime_mark_last_busy() before this. I missed this > > on the last round. Maybe in probe() too. Feel free to resend just this > > patch. > > > > > mutex_unlock(&ov5645->power_lock); > > > > > > return ret; > > > @@ -991,6 +970,10 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > > int ret; > > > > > > if (enable) { > > > + ret = pm_runtime_resume_and_get(ov5645->dev); > > > + if (ret < 0) > > > + return ret; > > > + > > > ret = ov5645_set_register_array(ov5645, > > > ov5645->current_mode->data, > > > ov5645->current_mode->data_size); > > > @@ -998,22 +981,22 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > > dev_err(ov5645->dev, "could not set mode %dx%d\n", > > > ov5645->current_mode->width, > > > ov5645->current_mode->height); > > > - return ret; > > > + goto err_rpm_put; > > > } > > > ret = v4l2_ctrl_handler_setup(&ov5645->ctrls); > > > if (ret < 0) { > > > dev_err(ov5645->dev, "could not sync v4l2 controls\n"); > > > - return ret; > > > + goto err_rpm_put; > > > } > > > > > > ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45); > > > if (ret < 0) > > > - return ret; > > > + goto err_rpm_put; > > > > > > ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0, > > > OV5645_SYSTEM_CTRL0_START); > > > if (ret < 0) > > > - return ret; > > > + goto err_rpm_put; > > > } else { > > > ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40); > > > if (ret < 0) > > > @@ -1023,14 +1006,15 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > > OV5645_SYSTEM_CTRL0_STOP); > > > if (ret < 0) > > > return ret; > > > + pm_runtime_put(ov5645->dev); This should be pm_runtime_put_autosuspend(), with a pm_runtime_mark_last_busy() call too. > > > } > > > > > > return 0; > > > -} > > > > > > -static const struct v4l2_subdev_core_ops ov5645_core_ops = { > > > - .s_power = ov5645_s_power, > > > -}; > > > +err_rpm_put: > > > + pm_runtime_put(ov5645->dev); Here I would go for pm_runtime_put_sync(), as a failure to start the stream would benefit from forcing power being cut off before the user tries again. > > > + return ret; > > > +} > > > > > > static const struct v4l2_subdev_video_ops ov5645_video_ops = { > > > .s_stream = ov5645_s_stream, > > > @@ -1046,7 +1030,6 @@ static const struct v4l2_subdev_pad_ops ov5645_subdev_pad_ops = { > > > }; > > > > > > static const struct v4l2_subdev_ops ov5645_subdev_ops = { > > > - .core = &ov5645_core_ops, > > > .video = &ov5645_video_ops, > > > .pad = &ov5645_subdev_pad_ops, > > > }; > > > @@ -1188,11 +1171,9 @@ static int ov5645_probe(struct i2c_client *client) > > > goto free_ctrl; > > > } > > > > > > - ret = ov5645_s_power(&ov5645->sd, true); > > > - if (ret < 0) { > > > - dev_err(dev, "could not power up OV5645\n"); > > > + ret = ov5645_set_power_on(dev); > > > + if (ret) > > > goto free_entity; > > > - } > > > > > > ret = ov5645_read_reg(ov5645, OV5645_CHIP_ID_HIGH, &chip_id_high); > > > if (ret < 0 || chip_id_high != OV5645_CHIP_ID_HIGH_BYTE) { > > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > > > + pm_runtime_set_active(dev); > > > + pm_runtime_get_noresume(dev); > > > + pm_runtime_enable(dev); > > > + > > > ret = ov5645_read_reg(ov5645, OV5645_AEC_PK_MANUAL, > > > &ov5645->aec_pk_manual); > > Totally unrelated to this patch, can we drop all these register reads ? > The registers are written through he ov5645_global_init_setting array, > we know what the values are. > > > > if (ret < 0) { > > > dev_err(dev, "could not read AEC/AGC mode\n"); > > > ret = -ENODEV; > > > - goto power_down; > > > + goto err_pm_runtime; > > > } > > > > > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG20, > > > @@ -1222,7 +1207,7 @@ static int ov5645_probe(struct i2c_client *client) > > > if (ret < 0) { > > > dev_err(dev, "could not read vflip value\n"); > > > ret = -ENODEV; > > > - goto power_down; > > > + goto err_pm_runtime; > > > } > > > > > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG21, > > > @@ -1230,23 +1215,30 @@ static int ov5645_probe(struct i2c_client *client) > > > if (ret < 0) { > > > dev_err(dev, "could not read hflip value\n"); > > > ret = -ENODEV; > > > - goto power_down; > > > + goto err_pm_runtime; > > > } > > > > > > - ov5645_s_power(&ov5645->sd, false); > > > - > > > ret = v4l2_async_register_subdev(&ov5645->sd); > > > if (ret < 0) { > > > dev_err(dev, "could not register v4l2 device\n"); > > > + pm_runtime_disable(dev); > > > + pm_runtime_set_suspended(dev); > > > goto free_entity; > > This looks weird, why do we need special handling of runtime PM here, > instead of just jumping to err_pm_runtime ? > > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > > > } > > > > > > + pm_runtime_set_autosuspend_delay(dev, 1000); > > > + pm_runtime_use_autosuspend(dev); > > > + pm_runtime_put_autosuspend(dev); > > > + > > > ov5645_entity_init_cfg(&ov5645->sd, NULL); > > > > > > return 0; > > > > > > +err_pm_runtime: > > > + pm_runtime_disable(dev); > > > + pm_runtime_put_noidle(dev); > > > power_down: > > > - ov5645_s_power(&ov5645->sd, false); > > > + ov5645_set_power_off(dev); > > > free_entity: > > > media_entity_cleanup(&ov5645->sd.entity); > > > free_ctrl: > > > @@ -1264,6 +1256,10 @@ static void ov5645_remove(struct i2c_client *client) > > > v4l2_async_unregister_subdev(&ov5645->sd); > > > media_entity_cleanup(&ov5645->sd.entity); > > > v4l2_ctrl_handler_free(&ov5645->ctrls); > > > + pm_runtime_disable(ov5645->dev); > > > + if (!pm_runtime_status_suspended(ov5645->dev)) > > > + ov5645_set_power_off(ov5645->dev); > > > + pm_runtime_set_suspended(ov5645->dev); > > > mutex_destroy(&ov5645->power_lock); > > > } > > > > > > @@ -1279,10 +1275,15 @@ static const struct of_device_id ov5645_of_match[] = { > > > }; > > > MODULE_DEVICE_TABLE(of, ov5645_of_match); > > > > > > +static const struct dev_pm_ops ov5645_pm_ops = { > > > + SET_RUNTIME_PM_OPS(ov5645_set_power_off, ov5645_set_power_on, NULL) > > > +}; > > > + > > > static struct i2c_driver ov5645_i2c_driver = { > > > .driver = { > > > .of_match_table = ov5645_of_match, > > > .name = "ov5645", > > > + .pm = &ov5645_pm_ops, > > > }, > > > .probe_new = ov5645_probe, > > > .remove = ov5645_remove,
Hi Laurent, Thank you for the review. On Sat, Oct 15, 2022 at 7:25 AM Laurent Pinchart <laurent.pinchart@ideasonboard.com> wrote: > > One more comment. > > On Sat, Oct 15, 2022 at 09:05:08AM +0300, Laurent Pinchart wrote: > > On Fri, Oct 14, 2022 at 07:18:11PM +0000, Sakari Ailus wrote: > > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > > > From: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > > > > > > > Switch to using runtime PM for power management. > > > > > > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> > > > > --- > > > > v1->v2 > > > > * Moved pm_runtime_*_autosuspend() calls after registering the subdev. > > > > --- > > > > drivers/media/i2c/Kconfig | 2 +- > > > > drivers/media/i2c/ov5645.c | 137 +++++++++++++++++++------------------ > > > > 2 files changed, 70 insertions(+), 69 deletions(-) > > > > > > > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig > > > > index 7806d4b81716..c0edd1017fe8 100644 > > > > --- a/drivers/media/i2c/Kconfig > > > > +++ b/drivers/media/i2c/Kconfig > > > > @@ -459,7 +459,7 @@ config VIDEO_OV5640 > > > > config VIDEO_OV5645 > > > > tristate "OmniVision OV5645 sensor support" > > > > depends on OF > > > > - depends on I2C && VIDEO_DEV > > > > + depends on I2C && PM && VIDEO_DEV > > > > select MEDIA_CONTROLLER > > > > select VIDEO_V4L2_SUBDEV_API > > > > select V4L2_FWNODE > > > > diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c > > > > index 81e4e87e1821..1551690a94e0 100644 > > > > --- a/drivers/media/i2c/ov5645.c > > > > +++ b/drivers/media/i2c/ov5645.c > > > > @@ -27,6 +27,7 @@ > > > > #include <linux/module.h> > > > > #include <linux/of.h> > > > > #include <linux/of_graph.h> > > > > +#include <linux/pm_runtime.h> > > > > #include <linux/regulator/consumer.h> > > > > #include <linux/slab.h> > > > > #include <linux/types.h> > > > > @@ -108,7 +109,6 @@ struct ov5645 { > > > > u8 timing_tc_reg21; > > > > > > > > struct mutex power_lock; /* lock to protect power state */ > > > > - int power_count; > > > > > > > > struct gpio_desc *enable_gpio; > > > > struct gpio_desc *rst_gpio; > > > > @@ -635,8 +635,24 @@ static int ov5645_set_register_array(struct ov5645 *ov5645, > > > > return 0; > > > > } > > > > > > > > -static int ov5645_set_power_on(struct ov5645 *ov5645) > > > > +static int ov5645_set_power_off(struct device *dev) > > > > { > > > > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > > > > + struct ov5645 *ov5645 = to_ov5645(sd); > > > > + > > > > + ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); > > > > I'm not sure this belongs here, but it can be addressed later. > > > > > > + gpiod_set_value_cansleep(ov5645->rst_gpio, 1); > > > > + gpiod_set_value_cansleep(ov5645->enable_gpio, 0); > > > > + clk_disable_unprepare(ov5645->xclk); > > > > + regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > > > + > > > > + return 0; > > > > +} > > > > + > > > > +static int ov5645_set_power_on(struct device *dev) > > > > +{ > > > > + struct v4l2_subdev *sd = dev_get_drvdata(dev); > > > > + struct ov5645 *ov5645 = to_ov5645(sd); > > > > int ret; > > > > > > > > ret = regulator_bulk_enable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > > > @@ -658,57 +674,19 @@ static int ov5645_set_power_on(struct ov5645 *ov5645) > > > > > > > > msleep(20); > > > > > > > > - return 0; > > > > -} > > > > - > > > > -static void ov5645_set_power_off(struct ov5645 *ov5645) > > > > -{ > > > > - gpiod_set_value_cansleep(ov5645->rst_gpio, 1); > > > > - gpiod_set_value_cansleep(ov5645->enable_gpio, 0); > > > > - clk_disable_unprepare(ov5645->xclk); > > > > - regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); > > > > -} > > > > - > > > > -static int ov5645_s_power(struct v4l2_subdev *sd, int on) > > > > -{ > > > > - struct ov5645 *ov5645 = to_ov5645(sd); > > > > - int ret = 0; > > > > - > > > > - mutex_lock(&ov5645->power_lock); > > > > - > > > > - /* If the power count is modified from 0 to != 0 or from != 0 to 0, > > > > - * update the power state. > > > > - */ > > > > - if (ov5645->power_count == !on) { > > > > - if (on) { > > > > - ret = ov5645_set_power_on(ov5645); > > > > - if (ret < 0) > > > > - goto exit; > > > > - > > > > - ret = ov5645_set_register_array(ov5645, > > > > - ov5645_global_init_setting, > > > > + ret = ov5645_set_register_array(ov5645, ov5645_global_init_setting, > > > > ARRAY_SIZE(ov5645_global_init_setting)); > > > > - if (ret < 0) { > > > > - dev_err(ov5645->dev, > > > > - "could not set init registers\n"); > > > > - ov5645_set_power_off(ov5645); > > > > - goto exit; > > > > - } > > > > - > > > > - usleep_range(500, 1000); > > > > - } else { > > > > - ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); > > > > - ov5645_set_power_off(ov5645); > > > > - } > > > > + if (ret < 0) { > > > > + dev_err(ov5645->dev, "could not set init registers\n"); > > > > + goto exit; > > > > } > > > > > > > > - /* Update the power count. */ > > > > - ov5645->power_count += on ? 1 : -1; > > > > - WARN_ON(ov5645->power_count < 0); > > > > + usleep_range(500, 1000); > > > > > > > > -exit: > > > > - mutex_unlock(&ov5645->power_lock); > > > > + return 0; > > > > > > > > +exit: > > > > + ov5645_set_power_off(dev); > > > > return ret; > > > > } > > > > > > > > @@ -795,7 +773,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > > > > int ret; > > > > > > > > mutex_lock(&ov5645->power_lock); > > > > - if (!ov5645->power_count) { > > > > + if (!pm_runtime_get_if_in_use(ov5645->dev)) { > > > > mutex_unlock(&ov5645->power_lock); > > > > return 0; > > > > } > > > > @@ -827,6 +805,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) > > > > break; > > > > } > > > > > > > > + pm_runtime_put_autosuspend(ov5645->dev); > > > > > > I think you'll need pm_runtime_mark_last_busy() before this. I missed this > > > on the last round. Maybe in probe() too. Feel free to resend just this > > > patch. > > > > > > > mutex_unlock(&ov5645->power_lock); > > > > > > > > return ret; > > > > @@ -991,6 +970,10 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > > > int ret; > > > > > > > > if (enable) { > > > > + ret = pm_runtime_resume_and_get(ov5645->dev); > > > > + if (ret < 0) > > > > + return ret; > > > > + > > > > ret = ov5645_set_register_array(ov5645, > > > > ov5645->current_mode->data, > > > > ov5645->current_mode->data_size); > > > > @@ -998,22 +981,22 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > > > dev_err(ov5645->dev, "could not set mode %dx%d\n", > > > > ov5645->current_mode->width, > > > > ov5645->current_mode->height); > > > > - return ret; > > > > + goto err_rpm_put; > > > > } > > > > ret = v4l2_ctrl_handler_setup(&ov5645->ctrls); > > > > if (ret < 0) { > > > > dev_err(ov5645->dev, "could not sync v4l2 controls\n"); > > > > - return ret; > > > > + goto err_rpm_put; > > > > } > > > > > > > > ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45); > > > > if (ret < 0) > > > > - return ret; > > > > + goto err_rpm_put; > > > > > > > > ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0, > > > > OV5645_SYSTEM_CTRL0_START); > > > > if (ret < 0) > > > > - return ret; > > > > + goto err_rpm_put; > > > > } else { > > > > ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40); > > > > if (ret < 0) > > > > @@ -1023,14 +1006,15 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) > > > > OV5645_SYSTEM_CTRL0_STOP); > > > > if (ret < 0) > > > > return ret; > > > > + pm_runtime_put(ov5645->dev); > > This should be pm_runtime_put_autosuspend(), with a > pm_runtime_mark_last_busy() call too. > OK. > > > > } > > > > > > > > return 0; > > > > -} > > > > > > > > -static const struct v4l2_subdev_core_ops ov5645_core_ops = { > > > > - .s_power = ov5645_s_power, > > > > -}; > > > > +err_rpm_put: > > > > + pm_runtime_put(ov5645->dev); > > Here I would go for pm_runtime_put_sync(), as a failure to start the > stream would benefit from forcing power being cut off before the user > tries again. > Agreed. > > > > + return ret; > > > > +} > > > > > > > > static const struct v4l2_subdev_video_ops ov5645_video_ops = { > > > > .s_stream = ov5645_s_stream, > > > > @@ -1046,7 +1030,6 @@ static const struct v4l2_subdev_pad_ops ov5645_subdev_pad_ops = { > > > > }; > > > > > > > > static const struct v4l2_subdev_ops ov5645_subdev_ops = { > > > > - .core = &ov5645_core_ops, > > > > .video = &ov5645_video_ops, > > > > .pad = &ov5645_subdev_pad_ops, > > > > }; > > > > @@ -1188,11 +1171,9 @@ static int ov5645_probe(struct i2c_client *client) > > > > goto free_ctrl; > > > > } > > > > > > > > - ret = ov5645_s_power(&ov5645->sd, true); > > > > - if (ret < 0) { > > > > - dev_err(dev, "could not power up OV5645\n"); > > > > + ret = ov5645_set_power_on(dev); > > > > + if (ret) > > > > goto free_entity; > > > > - } > > > > > > > > ret = ov5645_read_reg(ov5645, OV5645_CHIP_ID_HIGH, &chip_id_high); > > > > if (ret < 0 || chip_id_high != OV5645_CHIP_ID_HIGH_BYTE) { > > > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > > > > > + pm_runtime_set_active(dev); > > > > + pm_runtime_get_noresume(dev); > > > > + pm_runtime_enable(dev); > > > > + > > > > ret = ov5645_read_reg(ov5645, OV5645_AEC_PK_MANUAL, > > > > &ov5645->aec_pk_manual); > > > > Totally unrelated to this patch, can we drop all these register reads ? > > The registers are written through he ov5645_global_init_setting array, > > we know what the values are. > > Indeed, I'll have a closer look while working on the subdev state for this driver. > > > > if (ret < 0) { > > > > dev_err(dev, "could not read AEC/AGC mode\n"); > > > > ret = -ENODEV; > > > > - goto power_down; > > > > + goto err_pm_runtime; > > > > } > > > > > > > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG20, > > > > @@ -1222,7 +1207,7 @@ static int ov5645_probe(struct i2c_client *client) > > > > if (ret < 0) { > > > > dev_err(dev, "could not read vflip value\n"); > > > > ret = -ENODEV; > > > > - goto power_down; > > > > + goto err_pm_runtime; > > > > } > > > > > > > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG21, > > > > @@ -1230,23 +1215,30 @@ static int ov5645_probe(struct i2c_client *client) > > > > if (ret < 0) { > > > > dev_err(dev, "could not read hflip value\n"); > > > > ret = -ENODEV; > > > > - goto power_down; > > > > + goto err_pm_runtime; > > > > } > > > > > > > > - ov5645_s_power(&ov5645->sd, false); > > > > - > > > > ret = v4l2_async_register_subdev(&ov5645->sd); > > > > if (ret < 0) { > > > > dev_err(dev, "could not register v4l2 device\n"); > > > > + pm_runtime_disable(dev); > > > > + pm_runtime_set_suspended(dev); > > > > goto free_entity; > > > > This looks weird, why do we need special handling of runtime PM here, > > instead of just jumping to err_pm_runtime ? > > Agreed, I have fixed that now. > > Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > Cheers, Prabhakar
Hi Prabhakar, One more comment. On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > + pm_runtime_set_active(dev); > + pm_runtime_get_noresume(dev); > + pm_runtime_enable(dev); You won't gain anything by eanbling runtime PM here. Just move it to the end of the function before the rest of the calls. Error handling becomes more simple. > + > ret = ov5645_read_reg(ov5645, OV5645_AEC_PK_MANUAL, > &ov5645->aec_pk_manual); > if (ret < 0) { > dev_err(dev, "could not read AEC/AGC mode\n"); > ret = -ENODEV; > - goto power_down; > + goto err_pm_runtime; > } > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG20, > @@ -1222,7 +1207,7 @@ static int ov5645_probe(struct i2c_client *client) > if (ret < 0) { > dev_err(dev, "could not read vflip value\n"); > ret = -ENODEV; > - goto power_down; > + goto err_pm_runtime; > } > > ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG21, > @@ -1230,23 +1215,30 @@ static int ov5645_probe(struct i2c_client *client) > if (ret < 0) { > dev_err(dev, "could not read hflip value\n"); > ret = -ENODEV; > - goto power_down; > + goto err_pm_runtime; > } > > - ov5645_s_power(&ov5645->sd, false); > - > ret = v4l2_async_register_subdev(&ov5645->sd); > if (ret < 0) { > dev_err(dev, "could not register v4l2 device\n"); > + pm_runtime_disable(dev); > + pm_runtime_set_suspended(dev); > goto free_entity; > } > > + pm_runtime_set_autosuspend_delay(dev, 1000); > + pm_runtime_use_autosuspend(dev); > + pm_runtime_put_autosuspend(dev); > + > ov5645_entity_init_cfg(&ov5645->sd, NULL); > > return 0; > > +err_pm_runtime: > + pm_runtime_disable(dev); > + pm_runtime_put_noidle(dev); > power_down: > - ov5645_s_power(&ov5645->sd, false); > + ov5645_set_power_off(dev); > free_entity: > media_entity_cleanup(&ov5645->sd.entity); > free_ctrl:
Hi Sakari, On Thu, Oct 27, 2022 at 12:20 PM Sakari Ailus <sakari.ailus@linux.intel.com> wrote: > > Hi Prabhakar, > > One more comment. > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > + pm_runtime_set_active(dev); > > + pm_runtime_get_noresume(dev); > > + pm_runtime_enable(dev); > > You won't gain anything by eanbling runtime PM here. Just move it to the > end of the function before the rest of the calls. Error handling becomes > more simple. > If I move the above calls below I get the below warning: [ 2.633386] ov5645 0-003c: Runtime PM usage count underflow! This is because of the last patch which moves ov5645_entity_init_cfg() before registering the subdev. ov5645_entity_init_cfg() calls s_ctrl due to which we are seeing the above message. Please let me know how to proceed on this. Cheers, Prabhakar
Hi Prabhakar, On Thu, Oct 27, 2022 at 01:01:52PM +0100, Lad, Prabhakar wrote: > Hi Sakari, > > On Thu, Oct 27, 2022 at 12:20 PM Sakari Ailus > <sakari.ailus@linux.intel.com> wrote: > > > > Hi Prabhakar, > > > > One more comment. > > > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > > > + pm_runtime_set_active(dev); > > > + pm_runtime_get_noresume(dev); > > > + pm_runtime_enable(dev); > > > > You won't gain anything by eanbling runtime PM here. Just move it to the > > end of the function before the rest of the calls. Error handling becomes > > more simple. > > > If I move the above calls below I get the below warning: > > [ 2.633386] ov5645 0-003c: Runtime PM usage count underflow! > > This is because of the last patch which moves ov5645_entity_init_cfg() > before registering the subdev. ov5645_entity_init_cfg() calls s_ctrl > due to which we are seeing the above message. Please let me know how > to proceed on this. Ah. Yes, this is a problem with the usage pattern of pm_runtime_get_if_in_use(). But please don't change that. You can still move enabling runtime PM later in the function.
Hi Sakari, On Thu, Oct 27, 2022 at 1:47 PM Sakari Ailus <sakari.ailus@linux.intel.com> wrote: > > Hi Prabhakar, > > On Thu, Oct 27, 2022 at 01:01:52PM +0100, Lad, Prabhakar wrote: > > Hi Sakari, > > > > On Thu, Oct 27, 2022 at 12:20 PM Sakari Ailus > > <sakari.ailus@linux.intel.com> wrote: > > > > > > Hi Prabhakar, > > > > > > One more comment. > > > > > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > > > > > + pm_runtime_set_active(dev); > > > > + pm_runtime_get_noresume(dev); > > > > + pm_runtime_enable(dev); > > > > > > You won't gain anything by eanbling runtime PM here. Just move it to the > > > end of the function before the rest of the calls. Error handling becomes > > > more simple. > > > > > If I move the above calls below I get the below warning: > > > > [ 2.633386] ov5645 0-003c: Runtime PM usage count underflow! > > > > This is because of the last patch which moves ov5645_entity_init_cfg() > > before registering the subdev. ov5645_entity_init_cfg() calls s_ctrl > > due to which we are seeing the above message. Please let me know how > > to proceed on this. > > Ah. Yes, this is a problem with the usage pattern of > pm_runtime_get_if_in_use(). But please don't change that. > > You can still move enabling runtime PM later in the function. > Agreed, the final version looks like below: pm_runtime_set_active(dev); pm_runtime_get_noresume(dev); ov5645_entity_init_cfg(&ov5645->sd, NULL); ret = v4l2_async_register_subdev(&ov5645->sd); if (ret < 0) { dev_err(dev, "could not register v4l2 device\n"); goto err_pm_runtime; } pm_runtime_set_autosuspend_delay(dev, 1000); pm_runtime_use_autosuspend(dev); pm_runtime_enable(dev); Cheers, Prabhakar
Hi Prabhakar, On Thu, Oct 27, 2022 at 05:32:07PM +0100, Lad, Prabhakar wrote: > Hi Sakari, > > On Thu, Oct 27, 2022 at 1:47 PM Sakari Ailus > <sakari.ailus@linux.intel.com> wrote: > > > > Hi Prabhakar, > > > > On Thu, Oct 27, 2022 at 01:01:52PM +0100, Lad, Prabhakar wrote: > > > Hi Sakari, > > > > > > On Thu, Oct 27, 2022 at 12:20 PM Sakari Ailus > > > <sakari.ailus@linux.intel.com> wrote: > > > > > > > > Hi Prabhakar, > > > > > > > > One more comment. > > > > > > > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > > > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > > > > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > > > > > > > + pm_runtime_set_active(dev); > > > > > + pm_runtime_get_noresume(dev); > > > > > + pm_runtime_enable(dev); > > > > > > > > You won't gain anything by eanbling runtime PM here. Just move it to the > > > > end of the function before the rest of the calls. Error handling becomes > > > > more simple. > > > > > > > If I move the above calls below I get the below warning: > > > > > > [ 2.633386] ov5645 0-003c: Runtime PM usage count underflow! > > > > > > This is because of the last patch which moves ov5645_entity_init_cfg() > > > before registering the subdev. ov5645_entity_init_cfg() calls s_ctrl > > > due to which we are seeing the above message. Please let me know how > > > to proceed on this. > > > > Ah. Yes, this is a problem with the usage pattern of > > pm_runtime_get_if_in_use(). But please don't change that. > > > > You can still move enabling runtime PM later in the function. > > > Agreed, the final version looks like below: > > pm_runtime_set_active(dev); > pm_runtime_get_noresume(dev); > You'll have to enable runtime PM here, before pm_runtime_get_if_in_use() gets called. I'll see if it could be made to work in a sensible way when runtime PM isn't enabled yet. > ov5645_entity_init_cfg(&ov5645->sd, NULL); > > ret = v4l2_async_register_subdev(&ov5645->sd); > if (ret < 0) { > dev_err(dev, "could not register v4l2 device\n"); > goto err_pm_runtime; > } > > pm_runtime_set_autosuspend_delay(dev, 1000); > pm_runtime_use_autosuspend(dev); > pm_runtime_enable(dev);
Hi Sakari, On Thu, Oct 27, 2022 at 7:45 PM Sakari Ailus <sakari.ailus@linux.intel.com> wrote: > > Hi Prabhakar, > > On Thu, Oct 27, 2022 at 05:32:07PM +0100, Lad, Prabhakar wrote: > > Hi Sakari, > > > > On Thu, Oct 27, 2022 at 1:47 PM Sakari Ailus > > <sakari.ailus@linux.intel.com> wrote: > > > > > > Hi Prabhakar, > > > > > > On Thu, Oct 27, 2022 at 01:01:52PM +0100, Lad, Prabhakar wrote: > > > > Hi Sakari, > > > > > > > > On Thu, Oct 27, 2022 at 12:20 PM Sakari Ailus > > > > <sakari.ailus@linux.intel.com> wrote: > > > > > > > > > > Hi Prabhakar, > > > > > > > > > > One more comment. > > > > > > > > > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > > > > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > > > > > > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > > > > > > > > > + pm_runtime_set_active(dev); > > > > > > + pm_runtime_get_noresume(dev); > > > > > > + pm_runtime_enable(dev); > > > > > > > > > > You won't gain anything by eanbling runtime PM here. Just move it to the > > > > > end of the function before the rest of the calls. Error handling becomes > > > > > more simple. > > > > > > > > > If I move the above calls below I get the below warning: > > > > > > > > [ 2.633386] ov5645 0-003c: Runtime PM usage count underflow! > > > > > > > > This is because of the last patch which moves ov5645_entity_init_cfg() > > > > before registering the subdev. ov5645_entity_init_cfg() calls s_ctrl > > > > due to which we are seeing the above message. Please let me know how > > > > to proceed on this. > > > > > > Ah. Yes, this is a problem with the usage pattern of > > > pm_runtime_get_if_in_use(). But please don't change that. > > > > > > You can still move enabling runtime PM later in the function. > > > > > Agreed, the final version looks like below: > > > > pm_runtime_set_active(dev); > > pm_runtime_get_noresume(dev); > > > > You'll have to enable runtime PM here, before pm_runtime_get_if_in_use() > gets called. > > I'll see if it could be made to work in a sensible way when runtime PM > isn't enabled yet. > Agreed, I'll send out v3 after fixing the comments. Cheers, Prabhakar
Hi Prabhakar, On Thu, Oct 27, 2022 at 06:37:58PM +0000, Sakari Ailus wrote: > Hi Prabhakar, > > On Thu, Oct 27, 2022 at 05:32:07PM +0100, Lad, Prabhakar wrote: > > Hi Sakari, > > > > On Thu, Oct 27, 2022 at 1:47 PM Sakari Ailus > > <sakari.ailus@linux.intel.com> wrote: > > > > > > Hi Prabhakar, > > > > > > On Thu, Oct 27, 2022 at 01:01:52PM +0100, Lad, Prabhakar wrote: > > > > Hi Sakari, > > > > > > > > On Thu, Oct 27, 2022 at 12:20 PM Sakari Ailus > > > > <sakari.ailus@linux.intel.com> wrote: > > > > > > > > > > Hi Prabhakar, > > > > > > > > > > One more comment. > > > > > > > > > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > > > > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > > > > > > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > > > > > > > > > + pm_runtime_set_active(dev); > > > > > > + pm_runtime_get_noresume(dev); > > > > > > + pm_runtime_enable(dev); > > > > > > > > > > You won't gain anything by eanbling runtime PM here. Just move it to the > > > > > end of the function before the rest of the calls. Error handling becomes > > > > > more simple. > > > > > > > > > If I move the above calls below I get the below warning: > > > > > > > > [ 2.633386] ov5645 0-003c: Runtime PM usage count underflow! > > > > > > > > This is because of the last patch which moves ov5645_entity_init_cfg() > > > > before registering the subdev. ov5645_entity_init_cfg() calls s_ctrl > > > > due to which we are seeing the above message. Please let me know how > > > > to proceed on this. > > > > > > Ah. Yes, this is a problem with the usage pattern of > > > pm_runtime_get_if_in_use(). But please don't change that. > > > > > > You can still move enabling runtime PM later in the function. > > > > > Agreed, the final version looks like below: > > > > pm_runtime_set_active(dev); > > pm_runtime_get_noresume(dev); > > > > You'll have to enable runtime PM here, before pm_runtime_get_if_in_use() > gets called. > > I'll see if it could be made to work in a sensible way when runtime PM > isn't enabled yet. There are various ways how runtime PM interface functions generally work, and generally return an error when runtime PM is disabled. Incrementing the usage_count when runtime PM is disabled would make pm_runtime_get_if_in_use() very special and not match what the rest would do. Therefore I think it's best to keep this in the driver. After all, mo other driver needs this in the media tree, which is the major user of the function.
Hi Sakari, On Mon, Oct 31, 2022 at 2:25 PM Sakari Ailus <sakari.ailus@linux.intel.com> wrote: > > Hi Prabhakar, > > On Thu, Oct 27, 2022 at 06:37:58PM +0000, Sakari Ailus wrote: > > Hi Prabhakar, > > > > On Thu, Oct 27, 2022 at 05:32:07PM +0100, Lad, Prabhakar wrote: > > > Hi Sakari, > > > > > > On Thu, Oct 27, 2022 at 1:47 PM Sakari Ailus > > > <sakari.ailus@linux.intel.com> wrote: > > > > > > > > Hi Prabhakar, > > > > > > > > On Thu, Oct 27, 2022 at 01:01:52PM +0100, Lad, Prabhakar wrote: > > > > > Hi Sakari, > > > > > > > > > > On Thu, Oct 27, 2022 at 12:20 PM Sakari Ailus > > > > > <sakari.ailus@linux.intel.com> wrote: > > > > > > > > > > > > Hi Prabhakar, > > > > > > > > > > > > One more comment. > > > > > > > > > > > > On Fri, Oct 14, 2022 at 07:34:56PM +0100, Prabhakar wrote: > > > > > > > @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) > > > > > > > > > > > > > > dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); > > > > > > > > > > > > > > + pm_runtime_set_active(dev); > > > > > > > + pm_runtime_get_noresume(dev); > > > > > > > + pm_runtime_enable(dev); > > > > > > > > > > > > You won't gain anything by eanbling runtime PM here. Just move it to the > > > > > > end of the function before the rest of the calls. Error handling becomes > > > > > > more simple. > > > > > > > > > > > If I move the above calls below I get the below warning: > > > > > > > > > > [ 2.633386] ov5645 0-003c: Runtime PM usage count underflow! > > > > > > > > > > This is because of the last patch which moves ov5645_entity_init_cfg() > > > > > before registering the subdev. ov5645_entity_init_cfg() calls s_ctrl > > > > > due to which we are seeing the above message. Please let me know how > > > > > to proceed on this. > > > > > > > > Ah. Yes, this is a problem with the usage pattern of > > > > pm_runtime_get_if_in_use(). But please don't change that. > > > > > > > > You can still move enabling runtime PM later in the function. > > > > > > > Agreed, the final version looks like below: > > > > > > pm_runtime_set_active(dev); > > > pm_runtime_get_noresume(dev); > > > > > > > You'll have to enable runtime PM here, before pm_runtime_get_if_in_use() > > gets called. > > > > I'll see if it could be made to work in a sensible way when runtime PM > > isn't enabled yet. > > There are various ways how runtime PM interface functions generally work, > and generally return an error when runtime PM is disabled. Incrementing the > usage_count when runtime PM is disabled would make > pm_runtime_get_if_in_use() very special and not match what the rest would > do. Therefore I think it's best to keep this in the driver. After all, mo > other driver needs this in the media tree, which is the major user of the > function. > Thank you for digging deep into this. I'll keep it as is and send a v3. Cheers, Prabhakar
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig index 7806d4b81716..c0edd1017fe8 100644 --- a/drivers/media/i2c/Kconfig +++ b/drivers/media/i2c/Kconfig @@ -459,7 +459,7 @@ config VIDEO_OV5640 config VIDEO_OV5645 tristate "OmniVision OV5645 sensor support" depends on OF - depends on I2C && VIDEO_DEV + depends on I2C && PM && VIDEO_DEV select MEDIA_CONTROLLER select VIDEO_V4L2_SUBDEV_API select V4L2_FWNODE diff --git a/drivers/media/i2c/ov5645.c b/drivers/media/i2c/ov5645.c index 81e4e87e1821..1551690a94e0 100644 --- a/drivers/media/i2c/ov5645.c +++ b/drivers/media/i2c/ov5645.c @@ -27,6 +27,7 @@ #include <linux/module.h> #include <linux/of.h> #include <linux/of_graph.h> +#include <linux/pm_runtime.h> #include <linux/regulator/consumer.h> #include <linux/slab.h> #include <linux/types.h> @@ -108,7 +109,6 @@ struct ov5645 { u8 timing_tc_reg21; struct mutex power_lock; /* lock to protect power state */ - int power_count; struct gpio_desc *enable_gpio; struct gpio_desc *rst_gpio; @@ -635,8 +635,24 @@ static int ov5645_set_register_array(struct ov5645 *ov5645, return 0; } -static int ov5645_set_power_on(struct ov5645 *ov5645) +static int ov5645_set_power_off(struct device *dev) { + struct v4l2_subdev *sd = dev_get_drvdata(dev); + struct ov5645 *ov5645 = to_ov5645(sd); + + ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); + gpiod_set_value_cansleep(ov5645->rst_gpio, 1); + gpiod_set_value_cansleep(ov5645->enable_gpio, 0); + clk_disable_unprepare(ov5645->xclk); + regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); + + return 0; +} + +static int ov5645_set_power_on(struct device *dev) +{ + struct v4l2_subdev *sd = dev_get_drvdata(dev); + struct ov5645 *ov5645 = to_ov5645(sd); int ret; ret = regulator_bulk_enable(OV5645_NUM_SUPPLIES, ov5645->supplies); @@ -658,57 +674,19 @@ static int ov5645_set_power_on(struct ov5645 *ov5645) msleep(20); - return 0; -} - -static void ov5645_set_power_off(struct ov5645 *ov5645) -{ - gpiod_set_value_cansleep(ov5645->rst_gpio, 1); - gpiod_set_value_cansleep(ov5645->enable_gpio, 0); - clk_disable_unprepare(ov5645->xclk); - regulator_bulk_disable(OV5645_NUM_SUPPLIES, ov5645->supplies); -} - -static int ov5645_s_power(struct v4l2_subdev *sd, int on) -{ - struct ov5645 *ov5645 = to_ov5645(sd); - int ret = 0; - - mutex_lock(&ov5645->power_lock); - - /* If the power count is modified from 0 to != 0 or from != 0 to 0, - * update the power state. - */ - if (ov5645->power_count == !on) { - if (on) { - ret = ov5645_set_power_on(ov5645); - if (ret < 0) - goto exit; - - ret = ov5645_set_register_array(ov5645, - ov5645_global_init_setting, + ret = ov5645_set_register_array(ov5645, ov5645_global_init_setting, ARRAY_SIZE(ov5645_global_init_setting)); - if (ret < 0) { - dev_err(ov5645->dev, - "could not set init registers\n"); - ov5645_set_power_off(ov5645); - goto exit; - } - - usleep_range(500, 1000); - } else { - ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x58); - ov5645_set_power_off(ov5645); - } + if (ret < 0) { + dev_err(ov5645->dev, "could not set init registers\n"); + goto exit; } - /* Update the power count. */ - ov5645->power_count += on ? 1 : -1; - WARN_ON(ov5645->power_count < 0); + usleep_range(500, 1000); -exit: - mutex_unlock(&ov5645->power_lock); + return 0; +exit: + ov5645_set_power_off(dev); return ret; } @@ -795,7 +773,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) int ret; mutex_lock(&ov5645->power_lock); - if (!ov5645->power_count) { + if (!pm_runtime_get_if_in_use(ov5645->dev)) { mutex_unlock(&ov5645->power_lock); return 0; } @@ -827,6 +805,7 @@ static int ov5645_s_ctrl(struct v4l2_ctrl *ctrl) break; } + pm_runtime_put_autosuspend(ov5645->dev); mutex_unlock(&ov5645->power_lock); return ret; @@ -991,6 +970,10 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) int ret; if (enable) { + ret = pm_runtime_resume_and_get(ov5645->dev); + if (ret < 0) + return ret; + ret = ov5645_set_register_array(ov5645, ov5645->current_mode->data, ov5645->current_mode->data_size); @@ -998,22 +981,22 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) dev_err(ov5645->dev, "could not set mode %dx%d\n", ov5645->current_mode->width, ov5645->current_mode->height); - return ret; + goto err_rpm_put; } ret = v4l2_ctrl_handler_setup(&ov5645->ctrls); if (ret < 0) { dev_err(ov5645->dev, "could not sync v4l2 controls\n"); - return ret; + goto err_rpm_put; } ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x45); if (ret < 0) - return ret; + goto err_rpm_put; ret = ov5645_write_reg(ov5645, OV5645_SYSTEM_CTRL0, OV5645_SYSTEM_CTRL0_START); if (ret < 0) - return ret; + goto err_rpm_put; } else { ret = ov5645_write_reg(ov5645, OV5645_IO_MIPI_CTRL00, 0x40); if (ret < 0) @@ -1023,14 +1006,15 @@ static int ov5645_s_stream(struct v4l2_subdev *subdev, int enable) OV5645_SYSTEM_CTRL0_STOP); if (ret < 0) return ret; + pm_runtime_put(ov5645->dev); } return 0; -} -static const struct v4l2_subdev_core_ops ov5645_core_ops = { - .s_power = ov5645_s_power, -}; +err_rpm_put: + pm_runtime_put(ov5645->dev); + return ret; +} static const struct v4l2_subdev_video_ops ov5645_video_ops = { .s_stream = ov5645_s_stream, @@ -1046,7 +1030,6 @@ static const struct v4l2_subdev_pad_ops ov5645_subdev_pad_ops = { }; static const struct v4l2_subdev_ops ov5645_subdev_ops = { - .core = &ov5645_core_ops, .video = &ov5645_video_ops, .pad = &ov5645_subdev_pad_ops, }; @@ -1188,11 +1171,9 @@ static int ov5645_probe(struct i2c_client *client) goto free_ctrl; } - ret = ov5645_s_power(&ov5645->sd, true); - if (ret < 0) { - dev_err(dev, "could not power up OV5645\n"); + ret = ov5645_set_power_on(dev); + if (ret) goto free_entity; - } ret = ov5645_read_reg(ov5645, OV5645_CHIP_ID_HIGH, &chip_id_high); if (ret < 0 || chip_id_high != OV5645_CHIP_ID_HIGH_BYTE) { @@ -1209,12 +1190,16 @@ static int ov5645_probe(struct i2c_client *client) dev_info(dev, "OV5645 detected at address 0x%02x\n", client->addr); + pm_runtime_set_active(dev); + pm_runtime_get_noresume(dev); + pm_runtime_enable(dev); + ret = ov5645_read_reg(ov5645, OV5645_AEC_PK_MANUAL, &ov5645->aec_pk_manual); if (ret < 0) { dev_err(dev, "could not read AEC/AGC mode\n"); ret = -ENODEV; - goto power_down; + goto err_pm_runtime; } ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG20, @@ -1222,7 +1207,7 @@ static int ov5645_probe(struct i2c_client *client) if (ret < 0) { dev_err(dev, "could not read vflip value\n"); ret = -ENODEV; - goto power_down; + goto err_pm_runtime; } ret = ov5645_read_reg(ov5645, OV5645_TIMING_TC_REG21, @@ -1230,23 +1215,30 @@ static int ov5645_probe(struct i2c_client *client) if (ret < 0) { dev_err(dev, "could not read hflip value\n"); ret = -ENODEV; - goto power_down; + goto err_pm_runtime; } - ov5645_s_power(&ov5645->sd, false); - ret = v4l2_async_register_subdev(&ov5645->sd); if (ret < 0) { dev_err(dev, "could not register v4l2 device\n"); + pm_runtime_disable(dev); + pm_runtime_set_suspended(dev); goto free_entity; } + pm_runtime_set_autosuspend_delay(dev, 1000); + pm_runtime_use_autosuspend(dev); + pm_runtime_put_autosuspend(dev); + ov5645_entity_init_cfg(&ov5645->sd, NULL); return 0; +err_pm_runtime: + pm_runtime_disable(dev); + pm_runtime_put_noidle(dev); power_down: - ov5645_s_power(&ov5645->sd, false); + ov5645_set_power_off(dev); free_entity: media_entity_cleanup(&ov5645->sd.entity); free_ctrl: @@ -1264,6 +1256,10 @@ static void ov5645_remove(struct i2c_client *client) v4l2_async_unregister_subdev(&ov5645->sd); media_entity_cleanup(&ov5645->sd.entity); v4l2_ctrl_handler_free(&ov5645->ctrls); + pm_runtime_disable(ov5645->dev); + if (!pm_runtime_status_suspended(ov5645->dev)) + ov5645_set_power_off(ov5645->dev); + pm_runtime_set_suspended(ov5645->dev); mutex_destroy(&ov5645->power_lock); } @@ -1279,10 +1275,15 @@ static const struct of_device_id ov5645_of_match[] = { }; MODULE_DEVICE_TABLE(of, ov5645_of_match); +static const struct dev_pm_ops ov5645_pm_ops = { + SET_RUNTIME_PM_OPS(ov5645_set_power_off, ov5645_set_power_on, NULL) +}; + static struct i2c_driver ov5645_i2c_driver = { .driver = { .of_match_table = ov5645_of_match, .name = "ov5645", + .pm = &ov5645_pm_ops, }, .probe_new = ov5645_probe, .remove = ov5645_remove,