@@ -123,6 +123,33 @@ properties:
some PLLs, clocks and then brings up CPU0 for resuming the
system.
+ core-supply:
+ description:
+ Phandle to voltage regulator connected to the SoC Core power rail.
+
+ core-domain:
+ type: object
+ description: |
+ The vast majority of hardware blocks of Tegra SoC belong to a
+ Core power domain, which has a dedicated voltage rail that powers
+ the blocks.
+
+ properties:
+ operating-points-v2:
+ description:
+ Should contain level, voltages and opp-supported-hw property.
+ The supported-hw is a bitfield indicating SoC speedo or process
+ ID mask.
+
+ "#power-domain-cells":
+ const: 0
+
+ required:
+ - operating-points-v2
+ - "#power-domain-cells"
+
+ additionalProperties: false
+
i2c-thermtrip:
type: object
description:
@@ -300,33 +327,6 @@ patternProperties:
additionalProperties: false
- core-domain:
- type: object
- description: |
- The vast majority of hardware blocks of Tegra SoC belong to a
- Core power domain, which has a dedicated voltage rail that powers
- the blocks.
-
- properties:
- operating-points-v2:
- description:
- Should contain level, voltages and opp-supported-hw property.
- The supported-hw is a bitfield indicating SoC speedo or process
- ID mask.
-
- "#power-domain-cells":
- const: 0
-
- required:
- - operating-points-v2
- - "#power-domain-cells"
-
- additionalProperties: false
-
- core-supply:
- description:
- Phandle to voltage regulator connected to the SoC Core power rail.
-
required:
- compatible
- reg
@@ -51,13 +51,6 @@ properties:
where the board has a button wired to the pin and triggers
an interrupt on pressing it.
-patternProperties:
- "^buck[1-3]-supply$":
- description: Input supply phandle of one regulator.
-
- "^ldo[1-4]-supply$":
- description: Input supply phandle of one regulator.
-
regulators:
type: object
description: |
@@ -82,6 +75,13 @@ patternProperties:
additionalProperties: false
+patternProperties:
+ "^buck[1-3]-supply$":
+ description: Input supply phandle of one regulator.
+
+ "^ldo[1-4]-supply$":
+ description: Input supply phandle of one regulator.
+
required:
- compatible
- reg
@@ -109,38 +109,6 @@ properties:
maximum: 7
default: [0, 0, 0, 0]
- ti,asi-tx-drive:
- type: boolean
- description: |
- When set the device will set the Tx ASI output to a Hi-Z state for unused
- data cycles. Default is to drive the output low on unused ASI cycles.
-
-patternProperties:
- '^ti,gpo-config-[1-4]$':
- $ref: /schemas/types.yaml#/definitions/uint32-array
- description: |
- Defines the configuration and output driver for the general purpose
- output pins (GPO). These values are pairs, the first value is for the
- configuration type and the second value is for the output drive type.
- The array is defined as <GPO_CFG GPO_DRV>
-
- GPO output configuration can be one of the following:
-
- 0 - (default) disabled
- 1 - GPOX is configured as a general-purpose output (GPO)
- 2 - GPOX is configured as a device interrupt output (IRQ)
- 3 - GPOX is configured as a secondary ASI output (SDOUT2)
- 4 - GPOX is configured as a PDM clock output (PDMCLK)
-
- GPO output drive configuration for the GPO pins can be one of the following:
-
- 0d - (default) Hi-Z output
- 1d - Drive active low and active high
- 2d - Drive active low and weak high
- 3d - Drive active low and Hi-Z
- 4d - Drive weak low and active high
- 5d - Drive Hi-Z and active high
-
ti,gpio-config:
description: |
Defines the configuration and output drive for the General Purpose
@@ -183,6 +151,38 @@ patternProperties:
maximum: 15
default: [2, 2]
+ ti,asi-tx-drive:
+ type: boolean
+ description: |
+ When set the device will set the Tx ASI output to a Hi-Z state for unused
+ data cycles. Default is to drive the output low on unused ASI cycles.
+
+patternProperties:
+ '^ti,gpo-config-[1-4]$':
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ description: |
+ Defines the configuration and output driver for the general purpose
+ output pins (GPO). These values are pairs, the first value is for the
+ configuration type and the second value is for the output drive type.
+ The array is defined as <GPO_CFG GPO_DRV>
+
+ GPO output configuration can be one of the following:
+
+ 0 - (default) disabled
+ 1 - GPOX is configured as a general-purpose output (GPO)
+ 2 - GPOX is configured as a device interrupt output (IRQ)
+ 3 - GPOX is configured as a secondary ASI output (SDOUT2)
+ 4 - GPOX is configured as a PDM clock output (PDMCLK)
+
+ GPO output drive configuration for the GPO pins can be one of the following:
+
+ 0d - (default) Hi-Z output
+ 1d - Drive active low and active high
+ 2d - Drive active low and weak high
+ 3d - Drive active low and Hi-Z
+ 4d - Drive weak low and active high
+ 5d - Drive Hi-Z and active high
+
required:
- compatible
- reg
Fixed string node names should be under 'properties' rather than 'patternProperties'. Additionally, without beginning and end of line anchors, any prefix or suffix is allowed on the specified node name. These cases don't appear to want a prefix or suffix, so move them under 'properties'. In some cases, the diff turns out to look like we're moving some patterns rather than the fixed string properties. Signed-off-by: Rob Herring <robh@kernel.org> --- .../arm/tegra/nvidia,tegra20-pmc.yaml | 54 ++++++++-------- .../bindings/regulator/ti,tps65219.yaml | 14 ++-- .../bindings/sound/tlv320adcx140.yaml | 64 +++++++++---------- 3 files changed, 66 insertions(+), 66 deletions(-)