| Message ID | 20221205163754.221139-10-robert.foss@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Enable Display for SM8350 | expand |
On 05/12/2022 18:37, Robert Foss wrote: > Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these > nodes the display subsystem is configured to support > one DSI output. > > Signed-off-by: Robert Foss <robert.foss@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm8350.dtsi | 199 ++++++++++++++++++++++++++- > 1 file changed, 195 insertions(+), 4 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi > index 434f8e8b12c1..fb1c616c5e89 100644 > --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi > @@ -3,6 +3,7 @@ > * Copyright (c) 2020, Linaro Limited > */ > > +#include <dt-bindings/interconnect/qcom,sm8350.h> > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/clock/qcom,dispcc-sm8350.h> > #include <dt-bindings/clock/qcom,gcc-sm8350.h> > @@ -2536,14 +2537,203 @@ usb_2_dwc3: usb@a800000 { > }; > }; > > + mdss: mdss@ae00000 { display-sybsystem@ I also had this issue in sm8450.dtsi (and I'm going to fix it in the next revision). > + compatible = "qcom,sm8350-mdss"; > + reg = <0 0x0ae00000 0 0x1000>; > + reg-names = "mdss"; > + > + interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>, > + <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>; > + interconnect-names = "mdp0-mem", "mdp1-mem"; > + > + power-domains = <&dispcc MDSS_GDSC>; > + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>; > + clock-names = "iface", "bus", "nrt_bus", "core"; > + > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + iommus = <&apps_smmu 0x820 0x402>; > + > + status = "disabled"; > + > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + mdss_mdp: display-controller@ae01000 { > + compatible = "qcom,sm8350-dpu"; > + reg = <0 0x0ae01000 0 0x8f000>, > + <0 0x0aeb0000 0 0x2008>; > + reg-names = "mdp", "vbif"; > + > + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>, > + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + clock-names = "bus", > + "nrt_bus", > + "iface", > + "lut", > + "core", > + "vsync"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + assigned-clock-rates = <19200000>; > + > + operating-points-v2 = <&mdp_opp_table>; > + power-domains = <&rpmhpd SM8350_MMCX>; > + > + interrupt-parent = <&mdss>; > + interrupts = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dpu_intf1_out: endpoint { > + remote-endpoint = <&dsi0_in>; > + }; > + }; > + }; > + }; > + > + dsi0: dsi@ae94000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae94000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <4>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, > + <&dispcc DISP_CC_MDSS_ESC0_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; > + assigned-clock-parents = <&dsi0_phy 0>, > + <&dsi0_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8350_MMCX>; > + > + phys = <&dsi0_phy>; > + > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi0_in: endpoint { > + remote-endpoint = <&dpu_intf1_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi0_out: endpoint { > + }; > + }; > + }; > + > + mdp_opp_table: opp-table { The mdp (dpu?) opp table belongs to the display-controller node. > + compatible = "operating-points-v2"; > + > + /* TODO: opp-200000000 should work with > + * &rpmhpd_opp_low_svs, but one some of > + * sm8350_hdk boards reboot using this > + * opp. > + */ > + opp-200000000 { > + opp-hz = /bits/ 64 <200000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + I have been changing the dsi's opp table, not this one. > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-345000000 { > + opp-hz = /bits/ 64 <345000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + > + opp-460000000 { > + opp-hz = /bits/ 64 <460000000>; > + required-opps = <&rpmhpd_opp_nom>; > + }; > + }; > + }; > + > + dsi0_phy: phy@ae94400 { > + compatible = "qcom,dsi-phy-5nm-8350"; > + reg = <0 0x0ae94400 0 0x200>, > + <0 0x0ae94600 0 0x280>, > + <0 0x0ae94900 0 0x260>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + > + dsi_opp_table: dsi-opp-table { And this table should go to dsi node. > + compatible = "operating-points-v2"; > + > + opp-187500000 { > + opp-hz = /bits/ 64 <187500000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-358000000 { > + opp-hz = /bits/ 64 <358000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + }; > + }; > + }; > + > dispcc: clock-controller@af00000 { > compatible = "qcom,sm8350-dispcc"; > reg = <0 0x0af00000 0 0x10000>; > clocks = <&rpmhcc RPMH_CXO_CLK>, > - <0>, > - <0>, > - <0>, > - <0>, > + <&dsi0_phy 0>, <&dsi0_phy 1>, > + <0>, <0>, Let's probably add both DSI controllers and DSI PHYs. It's fine if you can not verify the second one for real. > <0>, > <0>; > clock-names = "bi_tcxo", > @@ -2558,6 +2748,7 @@ dispcc: clock-controller@af00000 { > #power-domain-cells = <1>; > > power-domains = <&rpmhpd SM8350_MMCX>; > + required-opps = <&rpmhpd_opp_low_svs>; As it's not a turbo level anymore, can we drop it completely? > }; > > adsp: remoteproc@17300000 {
On 05/12/2022 17:37, Robert Foss wrote: > Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these > nodes the display subsystem is configured to support > one DSI output. > > Signed-off-by: Robert Foss <robert.foss@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm8350.dtsi | 199 ++++++++++++++++++++++++++- > 1 file changed, 195 insertions(+), 4 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi > index 434f8e8b12c1..fb1c616c5e89 100644 > --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi > @@ -3,6 +3,7 @@ > * Copyright (c) 2020, Linaro Limited > */ > > +#include <dt-bindings/interconnect/qcom,sm8350.h> > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/clock/qcom,dispcc-sm8350.h> > #include <dt-bindings/clock/qcom,gcc-sm8350.h> > @@ -2536,14 +2537,203 @@ usb_2_dwc3: usb@a800000 { > }; > }; > > + mdss: mdss@ae00000 { Based on bindings: display-subsystem > + compatible = "qcom,sm8350-mdss"; > + reg = <0 0x0ae00000 0 0x1000>; > + reg-names = "mdss"; > + > + interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>, > + <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>; > + interconnect-names = "mdp0-mem", "mdp1-mem"; > + > + power-domains = <&dispcc MDSS_GDSC>; > + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>; > + clock-names = "iface", "bus", "nrt_bus", "core"; > + > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + iommus = <&apps_smmu 0x820 0x402>; > + > + status = "disabled"; > + > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + mdss_mdp: display-controller@ae01000 { > + compatible = "qcom,sm8350-dpu"; > + reg = <0 0x0ae01000 0 0x8f000>, > + <0 0x0aeb0000 0 0x2008>; > + reg-names = "mdp", "vbif"; > + > + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>, > + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + clock-names = "bus", > + "nrt_bus", > + "iface", > + "lut", > + "core", > + "vsync"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + assigned-clock-rates = <19200000>; > + > + operating-points-v2 = <&mdp_opp_table>; > + power-domains = <&rpmhpd SM8350_MMCX>; > + > + interrupt-parent = <&mdss>; > + interrupts = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dpu_intf1_out: endpoint { > + remote-endpoint = <&dsi0_in>; > + }; > + }; > + }; > + }; > + > + dsi0: dsi@ae94000 { > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae94000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <4>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, > + <&dispcc DISP_CC_MDSS_ESC0_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; > + assigned-clock-parents = <&dsi0_phy 0>, > + <&dsi0_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8350_MMCX>; > + > + phys = <&dsi0_phy>; > + > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi0_in: endpoint { > + remote-endpoint = <&dpu_intf1_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi0_out: endpoint { > + }; > + }; > + }; > + > + mdp_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + /* TODO: opp-200000000 should work with > + * &rpmhpd_opp_low_svs, but one some of > + * sm8350_hdk boards reboot using this > + * opp. > + */ > + opp-200000000 { > + opp-hz = /bits/ 64 <200000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-345000000 { > + opp-hz = /bits/ 64 <345000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + > + opp-460000000 { > + opp-hz = /bits/ 64 <460000000>; > + required-opps = <&rpmhpd_opp_nom>; > + }; > + }; > + }; > + > + dsi0_phy: phy@ae94400 { > + compatible = "qcom,dsi-phy-5nm-8350"; > + reg = <0 0x0ae94400 0 0x200>, > + <0 0x0ae94600 0 0x280>, > + <0 0x0ae94900 0 0x260>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + > + dsi_opp_table: dsi-opp-table { node name: opp-table > + compatible = "operating-points-v2"; > + > + opp-187500000 { > + opp-hz = /bits/ 64 <187500000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-358000000 { > + opp-hz = /bits/ 64 <358000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + }; > + }; > + }; > + Best regards, Krzysztof
On 05/12/2022 17:37, Robert Foss wrote: > Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these > nodes the display subsystem is configured to support > one DSI output. > > Signed-off-by: Robert Foss <robert.foss@linaro.org> > --- > arch/arm64/boot/dts/qcom/sm8350.dtsi | 199 ++++++++++++++++++++++++++- > 1 file changed, 195 insertions(+), 4 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi > index 434f8e8b12c1..fb1c616c5e89 100644 > --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi > +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi > @@ -3,6 +3,7 @@ > * Copyright (c) 2020, Linaro Limited > */ > > +#include <dt-bindings/interconnect/qcom,sm8350.h> > #include <dt-bindings/interrupt-controller/arm-gic.h> > #include <dt-bindings/clock/qcom,dispcc-sm8350.h> > #include <dt-bindings/clock/qcom,gcc-sm8350.h> > @@ -2536,14 +2537,203 @@ usb_2_dwc3: usb@a800000 { > }; > }; > > + mdss: mdss@ae00000 { > + compatible = "qcom,sm8350-mdss"; > + reg = <0 0x0ae00000 0 0x1000>; > + reg-names = "mdss"; > + > + interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>, > + <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>; > + interconnect-names = "mdp0-mem", "mdp1-mem"; > + > + power-domains = <&dispcc MDSS_GDSC>; > + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>; > + clock-names = "iface", "bus", "nrt_bus", "core"; > + > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + iommus = <&apps_smmu 0x820 0x402>; > + > + status = "disabled"; > + > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + mdss_mdp: display-controller@ae01000 { > + compatible = "qcom,sm8350-dpu"; > + reg = <0 0x0ae01000 0 0x8f000>, > + <0 0x0aeb0000 0 0x2008>; > + reg-names = "mdp", "vbif"; > + > + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, > + <&gcc GCC_DISP_SF_AXI_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, > + <&dispcc DISP_CC_MDSS_MDP_CLK>, > + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + clock-names = "bus", > + "nrt_bus", > + "iface", > + "lut", > + "core", > + "vsync"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; > + assigned-clock-rates = <19200000>; > + > + operating-points-v2 = <&mdp_opp_table>; > + power-domains = <&rpmhpd SM8350_MMCX>; > + > + interrupt-parent = <&mdss>; > + interrupts = <0>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dpu_intf1_out: endpoint { > + remote-endpoint = <&dsi0_in>; > + }; > + }; > + }; > + }; > + > + dsi0: dsi@ae94000 { With the 8280 patchset [1], it was decided that mdss nodes should now have a mdss_ prefix in their labels, to keep them near each other when referencing them in device DTSes. > + compatible = "qcom,mdss-dsi-ctrl"; > + reg = <0 0x0ae94000 0 0x400>; > + reg-names = "dsi_ctrl"; > + > + interrupt-parent = <&mdss>; > + interrupts = <4>; > + > + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, > + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, > + <&dispcc DISP_CC_MDSS_ESC0_CLK>, > + <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&gcc GCC_DISP_HF_AXI_CLK>; > + clock-names = "byte", > + "byte_intf", > + "pixel", > + "core", > + "iface", > + "bus"; > + > + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, > + <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; > + assigned-clock-parents = <&dsi0_phy 0>, > + <&dsi0_phy 1>; > + > + operating-points-v2 = <&dsi_opp_table>; > + power-domains = <&rpmhpd SM8350_MMCX>; > + > + phys = <&dsi0_phy>; > + > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dsi0_in: endpoint { > + remote-endpoint = <&dpu_intf1_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dsi0_out: endpoint { > + }; > + }; > + }; > + > + mdp_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + /* TODO: opp-200000000 should work with /* * TODO: and the wrapping looks rather weird.. or is that my email client? Other than that, lgtm! Konrad [1] https://lore.kernel.org/linux-arm-msm/20221130200739.ube7hvobythkbhuy@builder.lan/T/#m93e15b290b40c2d2c2ec6f639135ffa38882d0b2 > + * &rpmhpd_opp_low_svs, but one some of > + * sm8350_hdk boards reboot using this > + * opp. > + */ > + opp-200000000 { > + opp-hz = /bits/ 64 <200000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-345000000 { > + opp-hz = /bits/ 64 <345000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + > + opp-460000000 { > + opp-hz = /bits/ 64 <460000000>; > + required-opps = <&rpmhpd_opp_nom>; > + }; > + }; > + }; > + > + dsi0_phy: phy@ae94400 { > + compatible = "qcom,dsi-phy-5nm-8350"; > + reg = <0 0x0ae94400 0 0x200>, > + <0 0x0ae94600 0 0x280>, > + <0 0x0ae94900 0 0x260>; > + reg-names = "dsi_phy", > + "dsi_phy_lane", > + "dsi_pll"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>; > + clock-names = "iface", "ref"; > + > + status = "disabled"; > + > + dsi_opp_table: dsi-opp-table { > + compatible = "operating-points-v2"; > + > + opp-187500000 { > + opp-hz = /bits/ 64 <187500000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-300000000 { > + opp-hz = /bits/ 64 <300000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-358000000 { > + opp-hz = /bits/ 64 <358000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + }; > + }; > + }; > + > dispcc: clock-controller@af00000 { > compatible = "qcom,sm8350-dispcc"; > reg = <0 0x0af00000 0 0x10000>; > clocks = <&rpmhcc RPMH_CXO_CLK>, > - <0>, > - <0>, > - <0>, > - <0>, > + <&dsi0_phy 0>, <&dsi0_phy 1>, > + <0>, <0>, > <0>, > <0>; > clock-names = "bi_tcxo", > @@ -2558,6 +2748,7 @@ dispcc: clock-controller@af00000 { > #power-domain-cells = <1>; > > power-domains = <&rpmhpd SM8350_MMCX>; > + required-opps = <&rpmhpd_opp_low_svs>; > }; > > adsp: remoteproc@17300000 {
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi index 434f8e8b12c1..fb1c616c5e89 100644 --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -3,6 +3,7 @@ * Copyright (c) 2020, Linaro Limited */ +#include <dt-bindings/interconnect/qcom,sm8350.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/qcom,dispcc-sm8350.h> #include <dt-bindings/clock/qcom,gcc-sm8350.h> @@ -2536,14 +2537,203 @@ usb_2_dwc3: usb@a800000 { }; }; + mdss: mdss@ae00000 { + compatible = "qcom,sm8350-mdss"; + reg = <0 0x0ae00000 0 0x1000>; + reg-names = "mdss"; + + interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>, + <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>; + interconnect-names = "mdp0-mem", "mdp1-mem"; + + power-domains = <&dispcc MDSS_GDSC>; + resets = <&dispcc DISP_CC_MDSS_CORE_BCR>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&gcc GCC_DISP_SF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "bus", "nrt_bus", "core"; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_smmu 0x820 0x402>; + + status = "disabled"; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + mdss_mdp: display-controller@ae01000 { + compatible = "qcom,sm8350-dpu"; + reg = <0 0x0ae01000 0 0x8f000>, + <0 0x0aeb0000 0 0x2008>; + reg-names = "mdp", "vbif"; + + clocks = <&gcc GCC_DISP_HF_AXI_CLK>, + <&gcc GCC_DISP_SF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "bus", + "nrt_bus", + "iface", + "lut", + "core", + "vsync"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + assigned-clock-rates = <19200000>; + + operating-points-v2 = <&mdp_opp_table>; + power-domains = <&rpmhpd SM8350_MMCX>; + + interrupt-parent = <&mdss>; + interrupts = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi0: dsi@ae94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae94000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <4>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; + assigned-clock-parents = <&dsi0_phy 0>, + <&dsi0_phy 1>; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8350_MMCX>; + + phys = <&dsi0_phy>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&dpu_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + }; + }; + }; + + mdp_opp_table: opp-table { + compatible = "operating-points-v2"; + + /* TODO: opp-200000000 should work with + * &rpmhpd_opp_low_svs, but one some of + * sm8350_hdk boards reboot using this + * opp. + */ + opp-200000000 { + opp-hz = /bits/ 64 <200000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-345000000 { + opp-hz = /bits/ 64 <345000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-460000000 { + opp-hz = /bits/ 64 <460000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + dsi0_phy: phy@ae94400 { + compatible = "qcom,dsi-phy-5nm-8350"; + reg = <0 0x0ae94400 0 0x200>, + <0 0x0ae94600 0 0x280>, + <0 0x0ae94900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + + dsi_opp_table: dsi-opp-table { + compatible = "operating-points-v2"; + + opp-187500000 { + opp-hz = /bits/ 64 <187500000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-358000000 { + opp-hz = /bits/ 64 <358000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + }; + }; + }; + dispcc: clock-controller@af00000 { compatible = "qcom,sm8350-dispcc"; reg = <0 0x0af00000 0 0x10000>; clocks = <&rpmhcc RPMH_CXO_CLK>, - <0>, - <0>, - <0>, - <0>, + <&dsi0_phy 0>, <&dsi0_phy 1>, + <0>, <0>, <0>, <0>; clock-names = "bi_tcxo", @@ -2558,6 +2748,7 @@ dispcc: clock-controller@af00000 { #power-domain-cells = <1>; power-domains = <&rpmhpd SM8350_MMCX>; + required-opps = <&rpmhpd_opp_low_svs>; }; adsp: remoteproc@17300000 {
Add mdss, mdss_mdp, dsi0, dsi0_phy nodes. With these nodes the display subsystem is configured to support one DSI output. Signed-off-by: Robert Foss <robert.foss@linaro.org> --- arch/arm64/boot/dts/qcom/sm8350.dtsi | 199 ++++++++++++++++++++++++++- 1 file changed, 195 insertions(+), 4 deletions(-)