| Message ID | 20221130081430.67831-2-luca.weiss@fairphone.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | [v3,1/3] dt-bindings: phy: qcom,qmp-usb3-dp: Add sm6350 compatible | expand |
Luca, Vinod, On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: > Add the tables and config for the combo phy found on SM6350. > > Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> > --- > Changes since v2: > * Drop dp_txa/dp_txb changes, not required > * Fix dp_dp_phy offset > > drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ > 1 file changed, 126 insertions(+) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > index 77052c66cf70..6ac0c68269dc 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { > "phy", > }; > > +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { > + .com = 0x0000, > + .txa = 0x1200, > + .rxa = 0x1400, > + .txb = 0x1600, > + .rxb = 0x1800, > + .usb3_serdes = 0x1000, > + .usb3_pcs_misc = 0x1a00, > + .usb3_pcs = 0x1c00, > + .dp_serdes = 0x1000, I would have expected this to be 0x2000 as that's what the older platforms have been using for the dp serdes table so far. Without access to any documentation it's hard to tell whether everyone's just been cargo-culting all along or if there's actually something there at offset 0x2000. Vinod, could you shed some light on this as presumably you have access to some documentation? > + .dp_dp_phy = 0x2a00, > +}; Johan
Hi Johan, On Wed Dec 28, 2022 at 3:17 PM CET, Johan Hovold wrote: > Luca, Vinod, > > On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: > > Add the tables and config for the combo phy found on SM6350. > > > > Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> > > --- > > Changes since v2: > > * Drop dp_txa/dp_txb changes, not required > > * Fix dp_dp_phy offset > > > > drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ > > 1 file changed, 126 insertions(+) > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > index 77052c66cf70..6ac0c68269dc 100644 > > --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > > @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { > > "phy", > > }; > > > > +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { > > + .com = 0x0000, > > + .txa = 0x1200, > > + .rxa = 0x1400, > > + .txb = 0x1600, > > + .rxb = 0x1800, > > + .usb3_serdes = 0x1000, > > + .usb3_pcs_misc = 0x1a00, > > + .usb3_pcs = 0x1c00, > > + .dp_serdes = 0x1000, > > I would have expected this to be 0x2000 as that's what the older > platforms have been using for the dp serdes table so far. Without access > to any documentation it's hard to tell whether everyone's just been > cargo-culting all along or if there's actually something there at offset > 0x2000. From what I saw comparing downstream code vs mainline 0x1000 should be correct. From https://gerrit-public.fairphone.software/plugins/gitiles/kernel/msm-4.19/+/refs/heads/kernel/11/fp4/include/dt-bindings/phy/qcom,lagoon-qmp-usb3.h#38 USB3_DP_QSERDES_COM_BIAS_EN_CLKBUFLR_EN (downstream 0x1034) = QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN (mainline 0x034) USB3_DP_QSERDES_COM_CP_CTRL_MODE0 (downstream 0x1060) = QSERDES_V3_COM_CP_CTRL_MODE0 (mainline 0x060) These defines downstream are used in qcom,qmp-phy-init-seq (lagoon-usb.dtsi) which super abbreviated gets used like this: lagoon-usb.dtsi: reg = <0x88e8000 0x3000>; reg-names = "qmp_phy_base"; qcom,qmp-phy-init-seq = <...>; drivers/usb/phy/phy-msm-ssusb-qmp.c res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "qmp_phy_base"); phy->base = devm_ioremap_nocache(dev, res->start, resource_size(res)); of_property_read_u32_array(dev->of_node, "qcom,qmp-phy-init-seq", phy->qmp_phy_init_seq, phy->init_seq_len); reg = (struct qmp_reg_val *)phy->qmp_phy_init_seq; while (reg->offset != -1) { writel_relaxed(reg->val, phy->base + reg->offset); I don't see anywhere where an extra 0x1000 should come from. But perhaps I'm missing something. The reg address is the same downstream and mainline also. > > Vinod, could you shed some light on this as presumably you have access > to some documentation? That would be useful :) Regards Luca > > > + .dp_dp_phy = 0x2a00, > > +}; > > Johan
On 28-12-22, 15:17, Johan Hovold wrote: > Luca, Vinod, > > On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: > > Add the tables and config for the combo phy found on SM6350. > > > > Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> > > --- > > Changes since v2: > > * Drop dp_txa/dp_txb changes, not required > > * Fix dp_dp_phy offset > > > > drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ > > 1 file changed, 126 insertions(+) > > > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > index 77052c66cf70..6ac0c68269dc 100644 > > --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > > @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { > > "phy", > > }; > > > > +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { > > + .com = 0x0000, > > + .txa = 0x1200, > > + .rxa = 0x1400, > > + .txb = 0x1600, > > + .rxb = 0x1800, > > + .usb3_serdes = 0x1000, > > + .usb3_pcs_misc = 0x1a00, > > + .usb3_pcs = 0x1c00, > > + .dp_serdes = 0x1000, > > I would have expected this to be 0x2000 as that's what the older > platforms have been using for the dp serdes table so far. Without access > to any documentation it's hard to tell whether everyone's just been > cargo-culting all along or if there's actually something there at offset > 0x2000. > > Vinod, could you shed some light on this as presumably you have access > to some documentation? > > > + .dp_dp_phy = 0x2a00, No sorry, I dont have access to this version...
On 12/01/2023 19:50, Vinod Koul wrote: > On 28-12-22, 15:17, Johan Hovold wrote: >> Luca, Vinod, >> >> On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: >>> Add the tables and config for the combo phy found on SM6350. >>> >>> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> >>> --- >>> Changes since v2: >>> * Drop dp_txa/dp_txb changes, not required >>> * Fix dp_dp_phy offset >>> >>> drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ >>> 1 file changed, 126 insertions(+) >>> >>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c >>> index 77052c66cf70..6ac0c68269dc 100644 >>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c >>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c >> >>> @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { >>> "phy", >>> }; >>> >>> +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { >>> + .com = 0x0000, >>> + .txa = 0x1200, >>> + .rxa = 0x1400, >>> + .txb = 0x1600, >>> + .rxb = 0x1800, >>> + .usb3_serdes = 0x1000, >>> + .usb3_pcs_misc = 0x1a00, >>> + .usb3_pcs = 0x1c00, >>> + .dp_serdes = 0x1000, >> >> I would have expected this to be 0x2000 as that's what the older >> platforms have been using for the dp serdes table so far. Without access >> to any documentation it's hard to tell whether everyone's just been >> cargo-culting all along or if there's actually something there at offset >> 0x2000. usb3_serdes is 0x1000, so dp_serdes equal to 0x1000 is definitely an typo. Judging from the downstream dtsi, the DP PHY starts at offset 0x2000. So dp_serdes is equal to 0x2000, dp_phy = 0x2a00, ln_tx1 = 0x2200, ln_tx2 = 0x2600. >> >> Vinod, could you shed some light on this as presumably you have access >> to some documentation? >> >>> + .dp_dp_phy = 0x2a00, > > No sorry, I dont have access to this version... >
Hi Dmitry, On Thu Jan 12, 2023 at 8:33 PM CET, Dmitry Baryshkov wrote: > On 12/01/2023 19:50, Vinod Koul wrote: > > On 28-12-22, 15:17, Johan Hovold wrote: > >> Luca, Vinod, > >> > >> On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: > >>> Add the tables and config for the combo phy found on SM6350. > >>> > >>> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> > >>> --- > >>> Changes since v2: > >>> * Drop dp_txa/dp_txb changes, not required > >>> * Fix dp_dp_phy offset > >>> > >>> drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ > >>> 1 file changed, 126 insertions(+) > >>> > >>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > >>> index 77052c66cf70..6ac0c68269dc 100644 > >>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > >>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > >> > >>> @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { > >>> "phy", > >>> }; > >>> > >>> +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { > >>> + .com = 0x0000, > >>> + .txa = 0x1200, > >>> + .rxa = 0x1400, > >>> + .txb = 0x1600, > >>> + .rxb = 0x1800, > >>> + .usb3_serdes = 0x1000, > >>> + .usb3_pcs_misc = 0x1a00, > >>> + .usb3_pcs = 0x1c00, > >>> + .dp_serdes = 0x1000, > >> > >> I would have expected this to be 0x2000 as that's what the older > >> platforms have been using for the dp serdes table so far. Without access > >> to any documentation it's hard to tell whether everyone's just been > >> cargo-culting all along or if there's actually something there at offset > >> 0x2000. > > usb3_serdes is 0x1000, so dp_serdes equal to 0x1000 is definitely an typo. > > Judging from the downstream dtsi, the DP PHY starts at offset 0x2000. So > dp_serdes is equal to 0x2000, dp_phy = 0x2a00, ln_tx1 = 0x2200, ln_tx2 = > 0x2600. Can you share how you got to the 0x2000 offset? You can see my (potentially wrong) reasoning for 0x1000 a few messages ago[0]. The only 0x2000-something I could find now while looking at it again is "#define USB3_DP_PHY_DP_DP_PHY_PD_CTL 0x2a18" which becomes USB3_DP_DP_PHY_PD_CTL in the driver but this is seemingly not used at all in my msm-4.19 tree. Also if you have any idea on how to test it at runtime without actually having to get all the type-C functionality up I'd be happy to try that. Unfortunately I believe there's still quite some bits missing to actually get DP out via the USB-C port - which I imagine would trigger the PHY setup. [0] https://lore.kernel.org/linux-arm-msm/CPDIYQ3SSY3E.I0Y0NMIED0WO@otso/ Regards Luca > > >> > >> Vinod, could you shed some light on this as presumably you have access > >> to some documentation? > >> > >>> + .dp_dp_phy = 0x2a00, > > > > No sorry, I dont have access to this version... > > > > -- > With best wishes > Dmitry
On Fri, 13 Jan 2023 at 14:44, Luca Weiss <luca.weiss@fairphone.com> wrote: > > Hi Dmitry, > > On Thu Jan 12, 2023 at 8:33 PM CET, Dmitry Baryshkov wrote: > > On 12/01/2023 19:50, Vinod Koul wrote: > > > On 28-12-22, 15:17, Johan Hovold wrote: > > >> Luca, Vinod, > > >> > > >> On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: > > >>> Add the tables and config for the combo phy found on SM6350. > > >>> > > >>> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> > > >>> --- > > >>> Changes since v2: > > >>> * Drop dp_txa/dp_txb changes, not required > > >>> * Fix dp_dp_phy offset > > >>> > > >>> drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ > > >>> 1 file changed, 126 insertions(+) > > >>> > > >>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > >>> index 77052c66cf70..6ac0c68269dc 100644 > > >>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > >>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > >> > > >>> @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { > > >>> "phy", > > >>> }; > > >>> > > >>> +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { > > >>> + .com = 0x0000, > > >>> + .txa = 0x1200, > > >>> + .rxa = 0x1400, > > >>> + .txb = 0x1600, > > >>> + .rxb = 0x1800, > > >>> + .usb3_serdes = 0x1000, > > >>> + .usb3_pcs_misc = 0x1a00, > > >>> + .usb3_pcs = 0x1c00, > > >>> + .dp_serdes = 0x1000, > > >> > > >> I would have expected this to be 0x2000 as that's what the older > > >> platforms have been using for the dp serdes table so far. Without access > > >> to any documentation it's hard to tell whether everyone's just been > > >> cargo-culting all along or if there's actually something there at offset > > >> 0x2000. > > > > usb3_serdes is 0x1000, so dp_serdes equal to 0x1000 is definitely an typo. > > > > Judging from the downstream dtsi, the DP PHY starts at offset 0x2000. So > > dp_serdes is equal to 0x2000, dp_phy = 0x2a00, ln_tx1 = 0x2200, ln_tx2 = > > 0x2600. > > Can you share how you got to the 0x2000 offset? You can see my > (potentially wrong) reasoning for 0x1000 a few messages ago[0]. > > The only 0x2000-something I could find now while looking at it again is > "#define USB3_DP_PHY_DP_DP_PHY_PD_CTL 0x2a18" which becomes > USB3_DP_DP_PHY_PD_CTL in the driver but this is seemingly not used at > all in my msm-4.19 tree. Quite simple: see [1]. DP_PLL is at +0x2000 [1] https://android.googlesource.com/kernel/msm-extra/devicetree/+/refs/heads/android-msm-bramble-4.19-android11-qpr1/qcom/lagoon-sde-pll.dtsi#27 Anyway, having DP serdes at the space as USB3 serdes would mean that one would be setting USB3 PLL when trying to enable DP. So I could have said even w/o looking at the dtsi that dp serdes can _not_ be at 0x1000. > > Also if you have any idea on how to test it at runtime without actually > having to get all the type-C functionality up I'd be happy to try that. > Unfortunately I believe there's still quite some bits missing to > actually get DP out via the USB-C port - which I imagine would trigger > the PHY setup. Unfortunately, I don't have a recipe to test this. > > [0] https://lore.kernel.org/linux-arm-msm/CPDIYQ3SSY3E.I0Y0NMIED0WO@otso/ > > Regards > Luca
On Fri Jan 13, 2023 at 2:01 PM CET, Dmitry Baryshkov wrote: > On Fri, 13 Jan 2023 at 14:44, Luca Weiss <luca.weiss@fairphone.com> wrote: > > > > Hi Dmitry, > > > > On Thu Jan 12, 2023 at 8:33 PM CET, Dmitry Baryshkov wrote: > > > On 12/01/2023 19:50, Vinod Koul wrote: > > > > On 28-12-22, 15:17, Johan Hovold wrote: > > > >> Luca, Vinod, > > > >> > > > >> On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: > > > >>> Add the tables and config for the combo phy found on SM6350. > > > >>> > > > >>> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> > > > >>> --- > > > >>> Changes since v2: > > > >>> * Drop dp_txa/dp_txb changes, not required > > > >>> * Fix dp_dp_phy offset > > > >>> > > > >>> drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ > > > >>> 1 file changed, 126 insertions(+) > > > >>> > > > >>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > > >>> index 77052c66cf70..6ac0c68269dc 100644 > > > >>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > > >>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > > >> > > > >>> @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { > > > >>> "phy", > > > >>> }; > > > >>> > > > >>> +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { > > > >>> + .com = 0x0000, > > > >>> + .txa = 0x1200, > > > >>> + .rxa = 0x1400, > > > >>> + .txb = 0x1600, > > > >>> + .rxb = 0x1800, > > > >>> + .usb3_serdes = 0x1000, > > > >>> + .usb3_pcs_misc = 0x1a00, > > > >>> + .usb3_pcs = 0x1c00, > > > >>> + .dp_serdes = 0x1000, > > > >> > > > >> I would have expected this to be 0x2000 as that's what the older > > > >> platforms have been using for the dp serdes table so far. Without access > > > >> to any documentation it's hard to tell whether everyone's just been > > > >> cargo-culting all along or if there's actually something there at offset > > > >> 0x2000. > > > > > > usb3_serdes is 0x1000, so dp_serdes equal to 0x1000 is definitely an typo. > > > > > > Judging from the downstream dtsi, the DP PHY starts at offset 0x2000. So > > > dp_serdes is equal to 0x2000, dp_phy = 0x2a00, ln_tx1 = 0x2200, ln_tx2 = > > > 0x2600. > > > > Can you share how you got to the 0x2000 offset? You can see my > > (potentially wrong) reasoning for 0x1000 a few messages ago[0]. > > > > The only 0x2000-something I could find now while looking at it again is > > "#define USB3_DP_PHY_DP_DP_PHY_PD_CTL 0x2a18" which becomes > > USB3_DP_DP_PHY_PD_CTL in the driver but this is seemingly not used at > > all in my msm-4.19 tree. > > Quite simple: see [1]. DP_PLL is at +0x2000 > > [1] https://android.googlesource.com/kernel/msm-extra/devicetree/+/refs/heads/android-msm-bramble-4.19-android11-qpr1/qcom/lagoon-sde-pll.dtsi#27 I still disagree from what I see. E.g. this part of the dp_serdes init table in mainline: static const struct qmp_phy_init_tbl qmp_v3_dp_serdes_tbl_rbr[] = { QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x0c), With this one: #define QSERDES_V3_COM_HSCLK_SEL 0x13c To write this config qmp->dp_serdes gets used which is set at: qmp->dp_serdes = base + offs->dp_serdes; So if offs->dp_serdes is 0x2000, this write will go to 0x213c. If we go back to msm-4.19 downstream the equivalent define is #define USB3_DP_QSERDES_COM_HSCLK_SEL 0x113c So there we are at offset 0x1000. And this define is used in qcom,qmp-phy-init-seq which I already went to in detail in a previous email in this thread. > > Anyway, having DP serdes at the space as USB3 serdes would mean that > one would be setting USB3 PLL when trying to enable DP. So I could > have said even w/o looking at the dtsi that dp serdes can _not_ be at > 0x1000. I don't know enough about these PHY/DP/etc blocks to say anything there. > > > > > Also if you have any idea on how to test it at runtime without actually > > having to get all the type-C functionality up I'd be happy to try that. > > Unfortunately I believe there's still quite some bits missing to > > actually get DP out via the USB-C port - which I imagine would trigger > > the PHY setup. > > Unfortunately, I don't have a recipe to test this. No worries :) Regards Luca > > > > > [0] https://lore.kernel.org/linux-arm-msm/CPDIYQ3SSY3E.I0Y0NMIED0WO@otso/ > > > > Regards > > Luca > > > -- > With best wishes > Dmitry
On Fri, Jan 20, 2023 at 03:13:46PM +0100, Luca Weiss wrote: > On Fri Jan 13, 2023 at 2:01 PM CET, Dmitry Baryshkov wrote: > > On Fri, 13 Jan 2023 at 14:44, Luca Weiss <luca.weiss@fairphone.com> wrote: > > > > > > Hi Dmitry, > > > > > > On Thu Jan 12, 2023 at 8:33 PM CET, Dmitry Baryshkov wrote: > > > > On 12/01/2023 19:50, Vinod Koul wrote: > > > > > On 28-12-22, 15:17, Johan Hovold wrote: > > > > >> Luca, Vinod, > > > > >> > > > > >> On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: > > > > >>> Add the tables and config for the combo phy found on SM6350. > > > > >>> > > > > >>> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> > > > > >>> --- > > > > >>> Changes since v2: > > > > >>> * Drop dp_txa/dp_txb changes, not required > > > > >>> * Fix dp_dp_phy offset > > > > >>> > > > > >>> drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ > > > > >>> 1 file changed, 126 insertions(+) > > > > >>> > > > > >>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > > > >>> index 77052c66cf70..6ac0c68269dc 100644 > > > > >>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > > > >>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > > > > >> > > > > >>> @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { > > > > >>> "phy", > > > > >>> }; > > > > >>> > > > > >>> +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { > > > > >>> + .com = 0x0000, > > > > >>> + .txa = 0x1200, > > > > >>> + .rxa = 0x1400, > > > > >>> + .txb = 0x1600, > > > > >>> + .rxb = 0x1800, > > > > >>> + .usb3_serdes = 0x1000, > > > > >>> + .usb3_pcs_misc = 0x1a00, > > > > >>> + .usb3_pcs = 0x1c00, > > > > >>> + .dp_serdes = 0x1000, > > > > >> > > > > >> I would have expected this to be 0x2000 as that's what the older > > > > >> platforms have been using for the dp serdes table so far. Without access > > > > >> to any documentation it's hard to tell whether everyone's just been > > > > >> cargo-culting all along or if there's actually something there at offset > > > > >> 0x2000. > > > > > > > > usb3_serdes is 0x1000, so dp_serdes equal to 0x1000 is definitely an typo. > > > > > > > > Judging from the downstream dtsi, the DP PHY starts at offset 0x2000. So > > > > dp_serdes is equal to 0x2000, dp_phy = 0x2a00, ln_tx1 = 0x2200, ln_tx2 = > > > > 0x2600. > > > > > > Can you share how you got to the 0x2000 offset? You can see my > > > (potentially wrong) reasoning for 0x1000 a few messages ago[0]. > > > > > > The only 0x2000-something I could find now while looking at it again is > > > "#define USB3_DP_PHY_DP_DP_PHY_PD_CTL 0x2a18" which becomes > > > USB3_DP_DP_PHY_PD_CTL in the driver but this is seemingly not used at > > > all in my msm-4.19 tree. > > > > Quite simple: see [1]. DP_PLL is at +0x2000 > > > > [1] https://android.googlesource.com/kernel/msm-extra/devicetree/+/refs/heads/android-msm-bramble-4.19-android11-qpr1/qcom/lagoon-sde-pll.dtsi#27 > > I still disagree from what I see. > > E.g. this part of the dp_serdes init table in mainline: > > static const struct qmp_phy_init_tbl qmp_v3_dp_serdes_tbl_rbr[] = { > QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x0c), > > With this one: > #define QSERDES_V3_COM_HSCLK_SEL 0x13c > > To write this config qmp->dp_serdes gets used which is set at: > qmp->dp_serdes = base + offs->dp_serdes; > > So if offs->dp_serdes is 0x2000, this write will go to 0x213c. > > If we go back to msm-4.19 downstream the equivalent define is > #define USB3_DP_QSERDES_COM_HSCLK_SEL 0x113c > > So there we are at offset 0x1000. And this define is used in > qcom,qmp-phy-init-seq which I already went to in detail in a previous > email in this thread. From what I've heard, the PHY driver in the vendor kernel only deals with the USB part of the PHY, while some display driver accesses the DP part directly. So the fact that the Qualcomm USB PHY driver init sequences don't seem to use the DP regions (apart from that USB3_DP_PHY_DP_DP_PHY_PD_CTL register) is to be expected. IIRC the v3 layout was also used by the SoC for which DP support was first implemented. Presumably, the separate USB and DP regions do exist and you should include them also for SM6350 even if you can't test it currently. We'll convert the older platforms over to use the new binding scheme soon and then we'd need this anyway. And if it turns out later that this was all bogus, at least we only need to fix the driver (and not worry about dts backward compatibility as we had to with the old style bindings). Johan
On 23/01/2023 11:43, Johan Hovold wrote: > On Fri, Jan 20, 2023 at 03:13:46PM +0100, Luca Weiss wrote: >> On Fri Jan 13, 2023 at 2:01 PM CET, Dmitry Baryshkov wrote: >>> On Fri, 13 Jan 2023 at 14:44, Luca Weiss <luca.weiss@fairphone.com> wrote: >>>> >>>> Hi Dmitry, >>>> >>>> On Thu Jan 12, 2023 at 8:33 PM CET, Dmitry Baryshkov wrote: >>>>> On 12/01/2023 19:50, Vinod Koul wrote: >>>>>> On 28-12-22, 15:17, Johan Hovold wrote: >>>>>>> Luca, Vinod, >>>>>>> >>>>>>> On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: >>>>>>>> Add the tables and config for the combo phy found on SM6350. >>>>>>>> >>>>>>>> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> >>>>>>>> --- >>>>>>>> Changes since v2: >>>>>>>> * Drop dp_txa/dp_txb changes, not required >>>>>>>> * Fix dp_dp_phy offset >>>>>>>> >>>>>>>> drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ >>>>>>>> 1 file changed, 126 insertions(+) >>>>>>>> >>>>>>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c >>>>>>>> index 77052c66cf70..6ac0c68269dc 100644 >>>>>>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c >>>>>>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c >>>>>>> >>>>>>>> @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { >>>>>>>> "phy", >>>>>>>> }; >>>>>>>> >>>>>>>> +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { >>>>>>>> + .com = 0x0000, >>>>>>>> + .txa = 0x1200, >>>>>>>> + .rxa = 0x1400, >>>>>>>> + .txb = 0x1600, >>>>>>>> + .rxb = 0x1800, >>>>>>>> + .usb3_serdes = 0x1000, >>>>>>>> + .usb3_pcs_misc = 0x1a00, >>>>>>>> + .usb3_pcs = 0x1c00, >>>>>>>> + .dp_serdes = 0x1000, >>>>>>> >>>>>>> I would have expected this to be 0x2000 as that's what the older >>>>>>> platforms have been using for the dp serdes table so far. Without access >>>>>>> to any documentation it's hard to tell whether everyone's just been >>>>>>> cargo-culting all along or if there's actually something there at offset >>>>>>> 0x2000. >>>>> >>>>> usb3_serdes is 0x1000, so dp_serdes equal to 0x1000 is definitely an typo. >>>>> >>>>> Judging from the downstream dtsi, the DP PHY starts at offset 0x2000. So >>>>> dp_serdes is equal to 0x2000, dp_phy = 0x2a00, ln_tx1 = 0x2200, ln_tx2 = >>>>> 0x2600. >>>> >>>> Can you share how you got to the 0x2000 offset? You can see my >>>> (potentially wrong) reasoning for 0x1000 a few messages ago[0]. >>>> >>>> The only 0x2000-something I could find now while looking at it again is >>>> "#define USB3_DP_PHY_DP_DP_PHY_PD_CTL 0x2a18" which becomes >>>> USB3_DP_DP_PHY_PD_CTL in the driver but this is seemingly not used at >>>> all in my msm-4.19 tree. >>> >>> Quite simple: see [1]. DP_PLL is at +0x2000 >>> >>> [1] https://android.googlesource.com/kernel/msm-extra/devicetree/+/refs/heads/android-msm-bramble-4.19-android11-qpr1/qcom/lagoon-sde-pll.dtsi#27 >> >> I still disagree from what I see. >> >> E.g. this part of the dp_serdes init table in mainline: >> >> static const struct qmp_phy_init_tbl qmp_v3_dp_serdes_tbl_rbr[] = { >> QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x0c), >> >> With this one: >> #define QSERDES_V3_COM_HSCLK_SEL 0x13c >> >> To write this config qmp->dp_serdes gets used which is set at: >> qmp->dp_serdes = base + offs->dp_serdes; >> >> So if offs->dp_serdes is 0x2000, this write will go to 0x213c. >> >> If we go back to msm-4.19 downstream the equivalent define is >> #define USB3_DP_QSERDES_COM_HSCLK_SEL 0x113c There are two SERDES regions. One used by USB part of the PHY (at 0x1000) and another SERDES region used for DP (at 0x2000). As Johan described below, vendor kernel handles the DP regions in the DP driver. Possibly this caused a confusion on your side. >> >> So there we are at offset 0x1000. And this define is used in >> qcom,qmp-phy-init-seq which I already went to in detail in a previous >> email in this thread. > > From what I've heard, the PHY driver in the vendor kernel only deals > with the USB part of the PHY, while some display driver accesses the DP > part directly. So the fact that the Qualcomm USB PHY driver init > sequences don't seem to use the DP regions (apart from that > USB3_DP_PHY_DP_DP_PHY_PD_CTL register) is to be expected. Correct. > > IIRC the v3 layout was also used by the SoC for which DP support was > first implemented. Presumably, the separate USB and DP regions do exist > and you should include them also for SM6350 even if you can't test it > currently. Correct. sdm845 and sc7180 are v3 and they handle DP and USB3 regions separately inside a single Combo driver. > We'll convert the older platforms over to use the new binding scheme > soon and then we'd need this anyway. And if it turns out later that this > was all bogus, at least we only need to fix the driver (and not worry > about dts backward compatibility as we had to with the old style > bindings). As you mentioned this. Do you have plans to work on this conversion? If not, I'll probably take a look during next development window.
On Mon Jan 23, 2023 at 12:15 PM CET, Dmitry Baryshkov wrote: > On 23/01/2023 11:43, Johan Hovold wrote: > > On Fri, Jan 20, 2023 at 03:13:46PM +0100, Luca Weiss wrote: > >> On Fri Jan 13, 2023 at 2:01 PM CET, Dmitry Baryshkov wrote: > >>> On Fri, 13 Jan 2023 at 14:44, Luca Weiss <luca.weiss@fairphone.com> wrote: > >>>> > >>>> Hi Dmitry, > >>>> > >>>> On Thu Jan 12, 2023 at 8:33 PM CET, Dmitry Baryshkov wrote: > >>>>> On 12/01/2023 19:50, Vinod Koul wrote: > >>>>>> On 28-12-22, 15:17, Johan Hovold wrote: > >>>>>>> Luca, Vinod, > >>>>>>> > >>>>>>> On Wed, Nov 30, 2022 at 09:14:28AM +0100, Luca Weiss wrote: > >>>>>>>> Add the tables and config for the combo phy found on SM6350. > >>>>>>>> > >>>>>>>> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> > >>>>>>>> --- > >>>>>>>> Changes since v2: > >>>>>>>> * Drop dp_txa/dp_txb changes, not required > >>>>>>>> * Fix dp_dp_phy offset > >>>>>>>> > >>>>>>>> drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ > >>>>>>>> 1 file changed, 126 insertions(+) > >>>>>>>> > >>>>>>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > >>>>>>>> index 77052c66cf70..6ac0c68269dc 100644 > >>>>>>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > >>>>>>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c > >>>>>>> > >>>>>>>> @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { > >>>>>>>> "phy", > >>>>>>>> }; > >>>>>>>> > >>>>>>>> +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { > >>>>>>>> + .com = 0x0000, > >>>>>>>> + .txa = 0x1200, > >>>>>>>> + .rxa = 0x1400, > >>>>>>>> + .txb = 0x1600, > >>>>>>>> + .rxb = 0x1800, > >>>>>>>> + .usb3_serdes = 0x1000, > >>>>>>>> + .usb3_pcs_misc = 0x1a00, > >>>>>>>> + .usb3_pcs = 0x1c00, > >>>>>>>> + .dp_serdes = 0x1000, > >>>>>>> > >>>>>>> I would have expected this to be 0x2000 as that's what the older > >>>>>>> platforms have been using for the dp serdes table so far. Without access > >>>>>>> to any documentation it's hard to tell whether everyone's just been > >>>>>>> cargo-culting all along or if there's actually something there at offset > >>>>>>> 0x2000. > >>>>> > >>>>> usb3_serdes is 0x1000, so dp_serdes equal to 0x1000 is definitely an typo. > >>>>> > >>>>> Judging from the downstream dtsi, the DP PHY starts at offset 0x2000. So > >>>>> dp_serdes is equal to 0x2000, dp_phy = 0x2a00, ln_tx1 = 0x2200, ln_tx2 = > >>>>> 0x2600. > >>>> > >>>> Can you share how you got to the 0x2000 offset? You can see my > >>>> (potentially wrong) reasoning for 0x1000 a few messages ago[0]. > >>>> > >>>> The only 0x2000-something I could find now while looking at it again is > >>>> "#define USB3_DP_PHY_DP_DP_PHY_PD_CTL 0x2a18" which becomes > >>>> USB3_DP_DP_PHY_PD_CTL in the driver but this is seemingly not used at > >>>> all in my msm-4.19 tree. > >>> > >>> Quite simple: see [1]. DP_PLL is at +0x2000 > >>> > >>> [1] https://android.googlesource.com/kernel/msm-extra/devicetree/+/refs/heads/android-msm-bramble-4.19-android11-qpr1/qcom/lagoon-sde-pll.dtsi#27 > >> > >> I still disagree from what I see. > >> > >> E.g. this part of the dp_serdes init table in mainline: > >> > >> static const struct qmp_phy_init_tbl qmp_v3_dp_serdes_tbl_rbr[] = { > >> QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x0c), > >> > >> With this one: > >> #define QSERDES_V3_COM_HSCLK_SEL 0x13c > >> > >> To write this config qmp->dp_serdes gets used which is set at: > >> qmp->dp_serdes = base + offs->dp_serdes; > >> > >> So if offs->dp_serdes is 0x2000, this write will go to 0x213c. > >> > >> If we go back to msm-4.19 downstream the equivalent define is > >> #define USB3_DP_QSERDES_COM_HSCLK_SEL 0x113c > > There are two SERDES regions. One used by USB part of the PHY (at > 0x1000) and another SERDES region used for DP (at 0x2000). As Johan > described below, vendor kernel handles the DP regions in the DP driver. > Possibly this caused a confusion on your side. Ack, I think I got it now. I also see the registers used downstream now, e.g.: techpack/display/pll/dp_pll_10nm_util.c:#define QSERDES_COM_LOCK_CMP2_MODE0 0x009C So now .dp_serdes should be 0x2000. Do I need to change anything else also? I think not? Regards Luca > > >> > >> So there we are at offset 0x1000. And this define is used in > >> qcom,qmp-phy-init-seq which I already went to in detail in a previous > >> email in this thread. > > > > From what I've heard, the PHY driver in the vendor kernel only deals > > with the USB part of the PHY, while some display driver accesses the DP > > part directly. So the fact that the Qualcomm USB PHY driver init > > sequences don't seem to use the DP regions (apart from that > > USB3_DP_PHY_DP_DP_PHY_PD_CTL register) is to be expected. > > Correct. > > > > > IIRC the v3 layout was also used by the SoC for which DP support was > > first implemented. Presumably, the separate USB and DP regions do exist > > and you should include them also for SM6350 even if you can't test it > > currently. > > Correct. sdm845 and sc7180 are v3 and they handle DP and USB3 regions > separately inside a single Combo driver. > > > We'll convert the older platforms over to use the new binding scheme > > soon and then we'd need this anyway. And if it turns out later that this > > was all bogus, at least we only need to fix the driver (and not worry > > about dts backward compatibility as we had to with the old style > > bindings). > > As you mentioned this. Do you have plans to work on this conversion? If > not, I'll probably take a look during next development window. > -- > With best wishes > Dmitry
On Mon, Jan 23, 2023 at 12:22:32PM +0100, Luca Weiss wrote: > On Mon Jan 23, 2023 at 12:15 PM CET, Dmitry Baryshkov wrote: > > There are two SERDES regions. One used by USB part of the PHY (at > > 0x1000) and another SERDES region used for DP (at 0x2000). As Johan > > described below, vendor kernel handles the DP regions in the DP driver. > > Possibly this caused a confusion on your side. > > Ack, I think I got it now. I also see the registers used downstream > now, e.g.: > > techpack/display/pll/dp_pll_10nm_util.c:#define QSERDES_COM_LOCK_CMP2_MODE0 0x009C > > So now .dp_serdes should be 0x2000. Do I need to change anything else > also? I think not? You also need to add new dp_tx/rx pointers to the offset struct and use those in favour of the current ones if set. I think we hashed that bit out in one of the previous versions of this patch. Johan
On Mon, Jan 23, 2023 at 01:15:52PM +0200, Dmitry Baryshkov wrote: > On 23/01/2023 11:43, Johan Hovold wrote: > > We'll convert the older platforms over to use the new binding scheme > > soon and then we'd need this anyway. And if it turns out later that this > > was all bogus, at least we only need to fix the driver (and not worry > > about dts backward compatibility as we had to with the old style > > bindings). > > As you mentioned this. Do you have plans to work on this conversion? If > not, I'll probably take a look during next development window. Yes, I was planning on looking at this after Luca's series is merged. I have some higher prio stuff to get out the door these next couple of weeks first, though. Johan
On 23/01/2023 14:05, Johan Hovold wrote: > On Mon, Jan 23, 2023 at 01:15:52PM +0200, Dmitry Baryshkov wrote: >> On 23/01/2023 11:43, Johan Hovold wrote: > >>> We'll convert the older platforms over to use the new binding scheme >>> soon and then we'd need this anyway. And if it turns out later that this >>> was all bogus, at least we only need to fix the driver (and not worry >>> about dts backward compatibility as we had to with the old style >>> bindings). >> >> As you mentioned this. Do you have plans to work on this conversion? If >> not, I'll probably take a look during next development window. > > Yes, I was planning on looking at this after Luca's series is merged. I > have some higher prio stuff to get out the door these next couple of > weeks first, though. Ack, I'll sync with you then, let's see who has spare time for that.
On Mon Jan 23, 2023 at 1:03 PM CET, Johan Hovold wrote: > On Mon, Jan 23, 2023 at 12:22:32PM +0100, Luca Weiss wrote: > > On Mon Jan 23, 2023 at 12:15 PM CET, Dmitry Baryshkov wrote: > > > > There are two SERDES regions. One used by USB part of the PHY (at > > > 0x1000) and another SERDES region used for DP (at 0x2000). As Johan > > > described below, vendor kernel handles the DP regions in the DP driver. > > > Possibly this caused a confusion on your side. > > > > Ack, I think I got it now. I also see the registers used downstream > > now, e.g.: > > > > techpack/display/pll/dp_pll_10nm_util.c:#define QSERDES_COM_LOCK_CMP2_MODE0 0x009C > > > > So now .dp_serdes should be 0x2000. Do I need to change anything else > > also? I think not? > > You also need to add new dp_tx/rx pointers to the offset struct and use > those in favour of the current ones if set. I think we hashed that bit > out in one of the previous versions of this patch. Thanks for the persistent help, I've sent out v4 now, I hope that's good now and we can get this into v6.3 :) > > Johan
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c index 77052c66cf70..6ac0c68269dc 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c @@ -311,6 +311,70 @@ static const struct qmp_phy_init_tbl qmp_v3_usb3_pcs_tbl[] = { QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13), }; +static const struct qmp_phy_init_tbl sm6350_usb3_rx_tbl[] = { + QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x77), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x16), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x05), + QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75), +}; + +static const struct qmp_phy_init_tbl sm6350_usb3_pcs_tbl[] = { + /* FLL settings */ + QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02), + + /* Lock Det settings */ + QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b), + + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0xcc), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb7), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4e), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x65), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6b), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V1, 0x15), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x1d), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d), + + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_DET_HIGH_COUNT_VAL, 0x04), + + QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG1, 0x21), + QMP_PHY_INIT_CFG(QPHY_V3_PCS_REFGEN_REQ_CONFIG2, 0x60), +}; + static const struct qmp_phy_init_tbl sm8150_usb3_serdes_tbl[] = { QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_EN_CENTER, 0x01), QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER1, 0x31), @@ -975,6 +1039,19 @@ static const char * const sc7180_usb3phy_reset_l[] = { "phy", }; +static const struct qmp_combo_offsets qmp_combo_offsets_v3 = { + .com = 0x0000, + .txa = 0x1200, + .rxa = 0x1400, + .txb = 0x1600, + .rxb = 0x1800, + .usb3_serdes = 0x1000, + .usb3_pcs_misc = 0x1a00, + .usb3_pcs = 0x1c00, + .dp_serdes = 0x1000, + .dp_dp_phy = 0x2a00, +}; + static const struct qmp_combo_offsets qmp_combo_offsets_v5 = { .com = 0x0000, .txa = 0x0400, @@ -1172,6 +1249,51 @@ static const struct qmp_phy_cfg sc8280xp_usb43dpphy_cfg = { .regs = qmp_v4_usb3phy_regs_layout, }; +static const struct qmp_phy_cfg sm6350_usb3dpphy_cfg = { + .offsets = &qmp_combo_offsets_v3, + + .serdes_tbl = qmp_v3_usb3_serdes_tbl, + .serdes_tbl_num = ARRAY_SIZE(qmp_v3_usb3_serdes_tbl), + .tx_tbl = qmp_v3_usb3_tx_tbl, + .tx_tbl_num = ARRAY_SIZE(qmp_v3_usb3_tx_tbl), + .rx_tbl = sm6350_usb3_rx_tbl, + .rx_tbl_num = ARRAY_SIZE(sm6350_usb3_rx_tbl), + .pcs_tbl = sm6350_usb3_pcs_tbl, + .pcs_tbl_num = ARRAY_SIZE(sm6350_usb3_pcs_tbl), + + .dp_serdes_tbl = qmp_v3_dp_serdes_tbl, + .dp_serdes_tbl_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl), + .dp_tx_tbl = qmp_v3_dp_tx_tbl, + .dp_tx_tbl_num = ARRAY_SIZE(qmp_v3_dp_tx_tbl), + + .serdes_tbl_rbr = qmp_v3_dp_serdes_tbl_rbr, + .serdes_tbl_rbr_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl_rbr), + .serdes_tbl_hbr = qmp_v3_dp_serdes_tbl_hbr, + .serdes_tbl_hbr_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl_hbr), + .serdes_tbl_hbr2 = qmp_v3_dp_serdes_tbl_hbr2, + .serdes_tbl_hbr2_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl_hbr2), + .serdes_tbl_hbr3 = qmp_v3_dp_serdes_tbl_hbr3, + .serdes_tbl_hbr3_num = ARRAY_SIZE(qmp_v3_dp_serdes_tbl_hbr3), + + .swing_hbr_rbr = &qmp_dp_v3_voltage_swing_hbr_rbr, + .pre_emphasis_hbr_rbr = &qmp_dp_v3_pre_emphasis_hbr_rbr, + .swing_hbr3_hbr2 = &qmp_dp_v3_voltage_swing_hbr3_hbr2, + .pre_emphasis_hbr3_hbr2 = &qmp_dp_v3_pre_emphasis_hbr3_hbr2, + + .dp_aux_init = qmp_v3_dp_aux_init, + .configure_dp_tx = qmp_v3_configure_dp_tx, + .configure_dp_phy = qmp_v3_configure_dp_phy, + .calibrate_dp_phy = qmp_v3_calibrate_dp_phy, + + .clk_list = qmp_v4_phy_clk_l, + .num_clks = ARRAY_SIZE(qmp_v4_phy_clk_l), + .reset_list = msm8996_usb3phy_reset_l, + .num_resets = ARRAY_SIZE(msm8996_usb3phy_reset_l), + .vreg_list = qmp_phy_vreg_l, + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), + .regs = qmp_v3_usb3phy_regs_layout, +}; + static const struct qmp_phy_cfg sm8250_usb3dpphy_cfg = { .serdes_tbl = sm8150_usb3_serdes_tbl, .serdes_tbl_num = ARRAY_SIZE(sm8150_usb3_serdes_tbl), @@ -2789,6 +2911,10 @@ static const struct of_device_id qmp_combo_of_match_table[] = { .compatible = "qcom,sdm845-qmp-usb3-dp-phy", .data = &sdm845_usb3dpphy_cfg, }, + { + .compatible = "qcom,sm6350-qmp-usb3-dp-phy", + .data = &sm6350_usb3dpphy_cfg, + }, { .compatible = "qcom,sm8250-qmp-usb3-dp-phy", .data = &sm8250_usb3dpphy_cfg,
Add the tables and config for the combo phy found on SM6350. Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> --- Changes since v2: * Drop dp_txa/dp_txb changes, not required * Fix dp_dp_phy offset drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 126 ++++++++++++++++++++++ 1 file changed, 126 insertions(+)