| Message ID | 20230126083222.374243-2-herve.codina@bootlin.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add the PowerQUICC audio support using the QMC | expand |
On Thu, Jan 26, 2023 at 09:32:13AM +0100, Herve Codina wrote: > Add support for the time slot assigner (TSA) > available in some PowerQUICC SoC such as MPC885 > or MPC866. > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> > --- > .../bindings/soc/fsl/cpm_qe/fsl,tsa.yaml | 261 ++++++++++++++++++ fsl,cpm1-tsa.yaml > include/dt-bindings/soc/fsl,tsa.h | 13 + > 2 files changed, 274 insertions(+) > create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml > create mode 100644 include/dt-bindings/soc/fsl,tsa.h > > diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml > new file mode 100644 > index 000000000000..d027d4c3cf10 > --- /dev/null > +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml > @@ -0,0 +1,261 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,tsa.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: PowerQUICC CPM Time-slot assigner (TSA) controller > + > +maintainers: > + - Herve Codina <herve.codina@bootlin.com> > + > +description: > + The TSA is the time-slot assigner that can be found on some PowerQUICC SoC. > + Its purpose is to route some TDM time-slots to other internal serial > + controllers. > + > +properties: > + compatible: > + items: > + - enum: > + - fsl,mpc885-tsa > + - fsl,mpc866-tsa > + - const: fsl,cpm1-tsa > + > + reg: > + items: > + - description: SI (Serial Interface) register base > + - description: SI RAM base > + > + reg-names: > + items: > + - const: si_regs > + - const: si_ram > + > + '#address-cells': > + const: 1 > + > + '#size-cells': > + const: 0 > + > + '#serial-cells': Not a standard property. What's this for? #.*-cells applies to a specific pattern of properties. > + const: 1 > + > +patternProperties: > + '^tdm@[0-1]$': > + description: > + The TDM managed by this controller > + type: object > + > + additionalProperties: false > + > + properties: > + reg: > + minimum: 0 > + maximum: 1 > + description: > + The TDM number for this TDM, 0 for TDMa and 1 for TDMb > + > + fsl,common-rxtx-pins: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + The hardware can use four dedicated pins for Tx clock, Tx sync, Rx > + clock and Rx sync or use only two pins, Tx/Rx clock and Tx/Rx sync. > + Without the 'fsl,common-rxtx-pins' property, the four pins are used. > + With the 'fsl,common-rxtx-pins' property, two pins are used. > + > + clocks: > + minItems: 2 > + items: > + - description: External clock connected to L1RSYNC pin > + - description: External clock connected to L1RCLK pin > + - description: External clock connected to L1TSYNC pin > + - description: External clock connected to L1TCLK pin > + clock-names: > + minItems: 2 > + items: > + - const: l1rsync > + - const: l1rclk > + - const: l1tsync > + - const: l1tclk > + > + fsl,diagnostic-mode: > + $ref: /schemas/types.yaml#/definitions/string > + enum: [disabled, echo, internal-loopback, control-loopback] Seems like you would want userspace control of this, not have to make firmware changes and reboot to change. > + default: disabled > + description: | > + The diagnostic mode can be used to diagnose some communication issues. > + It should not be set (or set to 'disabled') when diagnostic is not > + needed. > + Diagnostic mode: > + - disabled: > + Diagnostic disabled (ie. normal operation) > + - echo: > + Automatic echo. Rx data is resent on Tx. > + - internal-loopback: > + The TDM transmitter is connected to the receiver. Data appears > + on Tx pin. > + - control-loopback: > + The TDM transmitter is connected to the receiver. The Tx pin is > + disconnected. > + > + fsl,rx-frame-sync-delay-bits: > + enum: [0, 1, 2, 3] > + default: 0 > + description: | > + Receive frame sync delay in number of bits. > + Indicates the delay between the Rx sync and the first bit of the Rx > + frame. 0 for no bit delay. 1, 2 or 3 for 1, 2 or 3 bits delay. > + > + fsl,tx-frame-sync-delay-bits: > + enum: [0, 1, 2, 3] > + default: 0 > + description: | > + Transmit frame sync delay in number of bits. > + Indicates the delay between the Tx sync and the first bit of the Tx > + frame. 0 for no bit delay. 1, 2 or 3 for 1, 2 or 3 bits delay. > + > + fsl,clock-falling-edge: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + Data is sent on falling edge of the clock (and received on the rising > + edge). If 'clock-falling-edge' is not present, data is sent on the > + rising edge (and received on the falling edge). > + > + fsl,fsync-rising-edge: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + Frame sync pulses are sampled with the rising edge of the channel > + clock. If 'fsync-rising-edge' is not present, pulses are sampled with > + the falling edge. > + > + fsl,double-speed-clock: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + The channel clock is twice the data rate. > + > + fsl,tx-ts-routes: > + $ref: /schemas/types.yaml#/definitions/uint32-matrix > + description: | > + A list of tupple that indicates the Tx time-slots routes. tuple > + tx_ts_routes = Not the property name. Put an example in the example(s). > + < 2 0 >, /* The first 2 time slots are not used */ > + < 3 1 >, /* The next 3 ones are route to SCC2 */ > + < 4 0 >, /* The next 4 ones are not used */ > + < 2 2 >; /* The nest 2 ones are route to SCC3 */ > + items: > + items: > + - description: > + The number of time-slots > + minimum: 1 > + maximum: 64 > + - description: | > + The source serial interface (dt-bindings/soc/fsl,tsa.h defines > + these values) > + - 0: No destination > + - 1: SCC2 > + - 2: SCC3 > + - 3: SCC4 > + - 4: SMC1 > + - 5: SMC2 > + enum: [0, 1, 2, 3, 4, 5] > + minItems: 1 > + maxItems: 64 > + > + fsl,rx-ts-routes: You could make these a pattern instead of duplicating the constraints: '^fsl,[rt]x-ts-routes$' > + $ref: /schemas/types.yaml#/definitions/uint32-matrix > + description: | > + A list of tupple that indicates the Rx time-slots routes. > + tx_ts_routes = > + < 2 0 >, /* The first 2 time slots are not used */ > + < 3 1 >, /* The next 3 ones are route from SCC2 */ > + < 4 0 >, /* The next 4 ones are not used */ > + < 2 2 >; /* The nest 2 ones are route from SCC3 */ > + items: > + items: > + - description: > + The number of time-slots > + minimum: 1 > + maximum: 64 > + - description: | > + The destination serial interface (dt-bindings/soc/fsl,tsa.h > + defines these values) > + - 0: No destination > + - 1: SCC2 > + - 2: SCC3 > + - 3: SCC4 > + - 4: SMC1 > + - 5: SMC2 > + enum: [0, 1, 2, 3, 4, 5] > + minItems: 1 > + maxItems: 64 > + > + allOf: > + # If fsl,common-rxtx-pins is present, only 2 clocks are needed. > + # Else, the 4 clocks must be present. > + - if: > + required: > + - fsl,common-rxtx-pins > + then: > + properties: > + clocks: > + maxItems: 2 > + clock-names: > + maxItems: 2 > + else: > + properties: > + clocks: > + minItems: 4 > + clock-names: > + minItems: 4 > + > + required: > + - reg > + - clocks > + - clock-names > + > +required: > + - compatible > + - reg > + - reg-names > + - '#address-cells' > + - '#size-cells' > + - '#serial-cells' > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/soc/fsl,tsa.h> > + > + tsa@ae0 { > + compatible = "fsl,mpc885-tsa", "fsl,cpm1-tsa"; > + reg = <0xae0 0x10>, > + <0xc00 0x200>; > + reg-names = "si_regs", "si_ram"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + #serial-cells = <1>; > + > + tdm@0 { > + /* TDMa */ > + reg = <0>; > + > + clocks = <&clk_l1rsynca>, <&clk_l1rclka>; > + clock-names = "l1rsync", "l1rclk"; > + > + fsl,common-rxtx-pins; > + fsl,fsync-rising-edge; > + > + fsl,tx-ts-routes = < 2 0 >, /* TS 0..1 */ > + < 24 FSL_CPM_TSA_SCC4 >, /* TS 2..25 */ > + < 1 0 >, /* TS 26 */ > + < 5 FSL_CPM_TSA_SCC3 >; /* TS 27..31 */ > + > + fsl,rx-ts-routes = < 2 0 >, /* TS 0..1 */ > + < 24 FSL_CPM_TSA_SCC4 >, /* 2..25 */ > + < 1 0 >, /* TS 26 */ > + < 5 FSL_CPM_TSA_SCC3 >; /* TS 27..31 */ > + }; > + }; > diff --git a/include/dt-bindings/soc/fsl,tsa.h b/include/dt-bindings/soc/fsl,tsa.h > new file mode 100644 > index 000000000000..2cc44e867dbe > --- /dev/null > +++ b/include/dt-bindings/soc/fsl,tsa.h > @@ -0,0 +1,13 @@ > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > + > +#ifndef __DT_BINDINGS_SOC_FSL_TSA_H > +#define __DT_BINDINGS_SOC_FSL_TSA_H > + > +#define FSL_CPM_TSA_NU 0 /* Pseuso Cell Id for not used item */ > +#define FSL_CPM_TSA_SCC2 1 > +#define FSL_CPM_TSA_SCC3 2 > +#define FSL_CPM_TSA_SCC4 3 > +#define FSL_CPM_TSA_SMC1 4 > +#define FSL_CPM_TSA_SMC2 5 > + > +#endif > -- > 2.39.0 >
On Mon, 30 Jan 2023 12:27:44 -0600 Hi Rob, Rob Herring <robh@kernel.org> wrote: > On Thu, Jan 26, 2023 at 09:32:13AM +0100, Herve Codina wrote: > > Add support for the time slot assigner (TSA) > > available in some PowerQUICC SoC such as MPC885 > > or MPC866. > > > > Signed-off-by: Herve Codina <herve.codina@bootlin.com> > > --- > > .../bindings/soc/fsl/cpm_qe/fsl,tsa.yaml | 261 ++++++++++++++++++ > > fsl,cpm1-tsa.yaml Right, will be change in next iteration. > > > include/dt-bindings/soc/fsl,tsa.h | 13 + > > 2 files changed, 274 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml > > create mode 100644 include/dt-bindings/soc/fsl,tsa.h > > > > diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml > > new file mode 100644 > > index 000000000000..d027d4c3cf10 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml > > @@ -0,0 +1,261 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,tsa.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: PowerQUICC CPM Time-slot assigner (TSA) controller > > + > > +maintainers: > > + - Herve Codina <herve.codina@bootlin.com> > > + > > +description: > > + The TSA is the time-slot assigner that can be found on some PowerQUICC SoC. > > + Its purpose is to route some TDM time-slots to other internal serial > > + controllers. > > + > > +properties: > > + compatible: > > + items: > > + - enum: > > + - fsl,mpc885-tsa > > + - fsl,mpc866-tsa > > + - const: fsl,cpm1-tsa > > + > > + reg: > > + items: > > + - description: SI (Serial Interface) register base > > + - description: SI RAM base > > + > > + reg-names: > > + items: > > + - const: si_regs > > + - const: si_ram > > + > > + '#address-cells': > > + const: 1 > > + > > + '#size-cells': > > + const: 0 > > + > > + '#serial-cells': > > Not a standard property. What's this for? #.*-cells applies to a > specific pattern of properties. A TSA consumer, such as QMC in this series, can have a phandle with an argument that points to this TSA node. For instance, in the QMC node, we have: fsl,tsa-serial = <&tsa FSL_CPM_TSA_SCC4>; The #serial-cells property in TSA specify the presence of this argument. What do you think if I add the following description: '#serial-cells': const: 1 description: TSA consumers that use a phandle to TSA need to pass the serial identifier with this phandle (defined in dt-bindings/soc/fsl,tsa.h). For instance "fsl,tsa-serial = <&tsa FSL_CPM_TSA_SCC4>;". > > > > + const: 1 > > + > > +patternProperties: > > + '^tdm@[0-1]$': > > + description: > > + The TDM managed by this controller > > + type: object > > + > > + additionalProperties: false > > + > > + properties: > > + reg: > > + minimum: 0 > > + maximum: 1 > > + description: > > + The TDM number for this TDM, 0 for TDMa and 1 for TDMb > > + > > + fsl,common-rxtx-pins: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: > > + The hardware can use four dedicated pins for Tx clock, Tx sync, Rx > > + clock and Rx sync or use only two pins, Tx/Rx clock and Tx/Rx sync. > > + Without the 'fsl,common-rxtx-pins' property, the four pins are used. > > + With the 'fsl,common-rxtx-pins' property, two pins are used. > > + > > + clocks: > > + minItems: 2 > > + items: > > + - description: External clock connected to L1RSYNC pin > > + - description: External clock connected to L1RCLK pin > > + - description: External clock connected to L1TSYNC pin > > + - description: External clock connected to L1TCLK pin > > + clock-names: > > + minItems: 2 > > + items: > > + - const: l1rsync > > + - const: l1rclk > > + - const: l1tsync > > + - const: l1tclk > > + > > + fsl,diagnostic-mode: > > + $ref: /schemas/types.yaml#/definitions/string > > + enum: [disabled, echo, internal-loopback, control-loopback] > > Seems like you would want userspace control of this, not have to make > firmware changes and reboot to change. I don't plan to give userspace control of this diagnostic mode. When I need to use this diagnostic mode, I plan to set this property in DT and reboot the system. > > > + default: disabled > > + description: | > > + The diagnostic mode can be used to diagnose some communication issues. > > + It should not be set (or set to 'disabled') when diagnostic is not > > + needed. > > + Diagnostic mode: > > + - disabled: > > + Diagnostic disabled (ie. normal operation) > > + - echo: > > + Automatic echo. Rx data is resent on Tx. > > + - internal-loopback: > > + The TDM transmitter is connected to the receiver. Data appears > > + on Tx pin. > > + - control-loopback: > > + The TDM transmitter is connected to the receiver. The Tx pin is > > + disconnected. > > + > > + fsl,rx-frame-sync-delay-bits: > > + enum: [0, 1, 2, 3] > > + default: 0 > > + description: | > > + Receive frame sync delay in number of bits. > > + Indicates the delay between the Rx sync and the first bit of the Rx > > + frame. 0 for no bit delay. 1, 2 or 3 for 1, 2 or 3 bits delay. > > + > > + fsl,tx-frame-sync-delay-bits: > > + enum: [0, 1, 2, 3] > > + default: 0 > > + description: | > > + Transmit frame sync delay in number of bits. > > + Indicates the delay between the Tx sync and the first bit of the Tx > > + frame. 0 for no bit delay. 1, 2 or 3 for 1, 2 or 3 bits delay. > > + > > + fsl,clock-falling-edge: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: > > + Data is sent on falling edge of the clock (and received on the rising > > + edge). If 'clock-falling-edge' is not present, data is sent on the > > + rising edge (and received on the falling edge). > > + > > + fsl,fsync-rising-edge: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: > > + Frame sync pulses are sampled with the rising edge of the channel > > + clock. If 'fsync-rising-edge' is not present, pulses are sampled with > > + the falling edge. > > + > > + fsl,double-speed-clock: > > + $ref: /schemas/types.yaml#/definitions/flag > > + description: > > + The channel clock is twice the data rate. > > + > > + fsl,tx-ts-routes: > > + $ref: /schemas/types.yaml#/definitions/uint32-matrix > > + description: | > > + A list of tupple that indicates the Tx time-slots routes. > > tuple Will be fixed in next iteration. > > > + tx_ts_routes = > > Not the property name. Put an example in the example(s). Oups, should be fsl,tx-ts-routes. An example is already present in the example section. I will remove this example from the description in the next iteration. > > > + < 2 0 >, /* The first 2 time slots are not used */ > > + < 3 1 >, /* The next 3 ones are route to SCC2 */ > > + < 4 0 >, /* The next 4 ones are not used */ > > + < 2 2 >; /* The nest 2 ones are route to SCC3 */ > > + items: > > + items: > > + - description: > > + The number of time-slots > > + minimum: 1 > > + maximum: 64 > > + - description: | > > + The source serial interface (dt-bindings/soc/fsl,tsa.h defines > > + these values) > > + - 0: No destination > > + - 1: SCC2 > > + - 2: SCC3 > > + - 3: SCC4 > > + - 4: SMC1 > > + - 5: SMC2 > > + enum: [0, 1, 2, 3, 4, 5] > > + minItems: 1 > > + maxItems: 64 > > + > > + fsl,rx-ts-routes: > > You could make these a pattern instead of duplicating the constraints: > > '^fsl,[rt]x-ts-routes$' Yes, I will use the pattern to handle tx and rx. As mentionned in fsl,tx-ts-routes, I will remove the example from the description as examples are already present in the example section. > > > + $ref: /schemas/types.yaml#/definitions/uint32-matrix > > + description: | > > + A list of tupple that indicates the Rx time-slots routes. > > + tx_ts_routes = > > + < 2 0 >, /* The first 2 time slots are not used */ > > + < 3 1 >, /* The next 3 ones are route from SCC2 */ > > + < 4 0 >, /* The next 4 ones are not used */ > > + < 2 2 >; /* The nest 2 ones are route from SCC3 */ > > + items: > > + items: > > + - description: > > + The number of time-slots > > + minimum: 1 > > + maximum: 64 > > + - description: | > > + The destination serial interface (dt-bindings/soc/fsl,tsa.h > > + defines these values) > > + - 0: No destination > > + - 1: SCC2 > > + - 2: SCC3 > > + - 3: SCC4 > > + - 4: SMC1 > > + - 5: SMC2 > > + enum: [0, 1, 2, 3, 4, 5] > > + minItems: 1 > > + maxItems: 64 > > + > > + allOf: > > + # If fsl,common-rxtx-pins is present, only 2 clocks are needed. > > + # Else, the 4 clocks must be present. > > + - if: > > + required: > > + - fsl,common-rxtx-pins > > + then: > > + properties: > > + clocks: > > + maxItems: 2 > > + clock-names: > > + maxItems: 2 > > + else: > > + properties: > > + clocks: > > + minItems: 4 > > + clock-names: > > + minItems: 4 > > + > > + required: > > + - reg > > + - clocks > > + - clock-names > > + > > +required: > > + - compatible > > + - reg > > + - reg-names > > + - '#address-cells' > > + - '#size-cells' > > + - '#serial-cells' > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/soc/fsl,tsa.h> > > + > > + tsa@ae0 { > > + compatible = "fsl,mpc885-tsa", "fsl,cpm1-tsa"; > > + reg = <0xae0 0x10>, > > + <0xc00 0x200>; > > + reg-names = "si_regs", "si_ram"; > > + > > + #address-cells = <1>; > > + #size-cells = <0>; > > + #serial-cells = <1>; > > + > > + tdm@0 { > > + /* TDMa */ > > + reg = <0>; > > + > > + clocks = <&clk_l1rsynca>, <&clk_l1rclka>; > > + clock-names = "l1rsync", "l1rclk"; > > + > > + fsl,common-rxtx-pins; > > + fsl,fsync-rising-edge; > > + > > + fsl,tx-ts-routes = < 2 0 >, /* TS 0..1 */ > > + < 24 FSL_CPM_TSA_SCC4 >, /* TS 2..25 */ > > + < 1 0 >, /* TS 26 */ > > + < 5 FSL_CPM_TSA_SCC3 >; /* TS 27..31 */ > > + > > + fsl,rx-ts-routes = < 2 0 >, /* TS 0..1 */ > > + < 24 FSL_CPM_TSA_SCC4 >, /* 2..25 */ > > + < 1 0 >, /* TS 26 */ > > + < 5 FSL_CPM_TSA_SCC3 >; /* TS 27..31 */ > > + }; > > + }; > > diff --git a/include/dt-bindings/soc/fsl,tsa.h b/include/dt-bindings/soc/fsl,tsa.h > > new file mode 100644 > > index 000000000000..2cc44e867dbe > > --- /dev/null > > +++ b/include/dt-bindings/soc/fsl,tsa.h > > @@ -0,0 +1,13 @@ > > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > > + > > +#ifndef __DT_BINDINGS_SOC_FSL_TSA_H > > +#define __DT_BINDINGS_SOC_FSL_TSA_H > > + > > +#define FSL_CPM_TSA_NU 0 /* Pseuso Cell Id for not used item */ > > +#define FSL_CPM_TSA_SCC2 1 > > +#define FSL_CPM_TSA_SCC3 2 > > +#define FSL_CPM_TSA_SCC4 3 > > +#define FSL_CPM_TSA_SMC1 4 > > +#define FSL_CPM_TSA_SMC2 5 > > + > > +#endif > > -- > > 2.39.0 > > Thanks for the review, Hervé
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml new file mode 100644 index 000000000000..d027d4c3cf10 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml @@ -0,0 +1,261 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soc/fsl/cpm_qe/fsl,tsa.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: PowerQUICC CPM Time-slot assigner (TSA) controller + +maintainers: + - Herve Codina <herve.codina@bootlin.com> + +description: + The TSA is the time-slot assigner that can be found on some PowerQUICC SoC. + Its purpose is to route some TDM time-slots to other internal serial + controllers. + +properties: + compatible: + items: + - enum: + - fsl,mpc885-tsa + - fsl,mpc866-tsa + - const: fsl,cpm1-tsa + + reg: + items: + - description: SI (Serial Interface) register base + - description: SI RAM base + + reg-names: + items: + - const: si_regs + - const: si_ram + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + '#serial-cells': + const: 1 + +patternProperties: + '^tdm@[0-1]$': + description: + The TDM managed by this controller + type: object + + additionalProperties: false + + properties: + reg: + minimum: 0 + maximum: 1 + description: + The TDM number for this TDM, 0 for TDMa and 1 for TDMb + + fsl,common-rxtx-pins: + $ref: /schemas/types.yaml#/definitions/flag + description: + The hardware can use four dedicated pins for Tx clock, Tx sync, Rx + clock and Rx sync or use only two pins, Tx/Rx clock and Tx/Rx sync. + Without the 'fsl,common-rxtx-pins' property, the four pins are used. + With the 'fsl,common-rxtx-pins' property, two pins are used. + + clocks: + minItems: 2 + items: + - description: External clock connected to L1RSYNC pin + - description: External clock connected to L1RCLK pin + - description: External clock connected to L1TSYNC pin + - description: External clock connected to L1TCLK pin + clock-names: + minItems: 2 + items: + - const: l1rsync + - const: l1rclk + - const: l1tsync + - const: l1tclk + + fsl,diagnostic-mode: + $ref: /schemas/types.yaml#/definitions/string + enum: [disabled, echo, internal-loopback, control-loopback] + default: disabled + description: | + The diagnostic mode can be used to diagnose some communication issues. + It should not be set (or set to 'disabled') when diagnostic is not + needed. + Diagnostic mode: + - disabled: + Diagnostic disabled (ie. normal operation) + - echo: + Automatic echo. Rx data is resent on Tx. + - internal-loopback: + The TDM transmitter is connected to the receiver. Data appears + on Tx pin. + - control-loopback: + The TDM transmitter is connected to the receiver. The Tx pin is + disconnected. + + fsl,rx-frame-sync-delay-bits: + enum: [0, 1, 2, 3] + default: 0 + description: | + Receive frame sync delay in number of bits. + Indicates the delay between the Rx sync and the first bit of the Rx + frame. 0 for no bit delay. 1, 2 or 3 for 1, 2 or 3 bits delay. + + fsl,tx-frame-sync-delay-bits: + enum: [0, 1, 2, 3] + default: 0 + description: | + Transmit frame sync delay in number of bits. + Indicates the delay between the Tx sync and the first bit of the Tx + frame. 0 for no bit delay. 1, 2 or 3 for 1, 2 or 3 bits delay. + + fsl,clock-falling-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Data is sent on falling edge of the clock (and received on the rising + edge). If 'clock-falling-edge' is not present, data is sent on the + rising edge (and received on the falling edge). + + fsl,fsync-rising-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: + Frame sync pulses are sampled with the rising edge of the channel + clock. If 'fsync-rising-edge' is not present, pulses are sampled with + the falling edge. + + fsl,double-speed-clock: + $ref: /schemas/types.yaml#/definitions/flag + description: + The channel clock is twice the data rate. + + fsl,tx-ts-routes: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + description: | + A list of tupple that indicates the Tx time-slots routes. + tx_ts_routes = + < 2 0 >, /* The first 2 time slots are not used */ + < 3 1 >, /* The next 3 ones are route to SCC2 */ + < 4 0 >, /* The next 4 ones are not used */ + < 2 2 >; /* The nest 2 ones are route to SCC3 */ + items: + items: + - description: + The number of time-slots + minimum: 1 + maximum: 64 + - description: | + The source serial interface (dt-bindings/soc/fsl,tsa.h defines + these values) + - 0: No destination + - 1: SCC2 + - 2: SCC3 + - 3: SCC4 + - 4: SMC1 + - 5: SMC2 + enum: [0, 1, 2, 3, 4, 5] + minItems: 1 + maxItems: 64 + + fsl,rx-ts-routes: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + description: | + A list of tupple that indicates the Rx time-slots routes. + tx_ts_routes = + < 2 0 >, /* The first 2 time slots are not used */ + < 3 1 >, /* The next 3 ones are route from SCC2 */ + < 4 0 >, /* The next 4 ones are not used */ + < 2 2 >; /* The nest 2 ones are route from SCC3 */ + items: + items: + - description: + The number of time-slots + minimum: 1 + maximum: 64 + - description: | + The destination serial interface (dt-bindings/soc/fsl,tsa.h + defines these values) + - 0: No destination + - 1: SCC2 + - 2: SCC3 + - 3: SCC4 + - 4: SMC1 + - 5: SMC2 + enum: [0, 1, 2, 3, 4, 5] + minItems: 1 + maxItems: 64 + + allOf: + # If fsl,common-rxtx-pins is present, only 2 clocks are needed. + # Else, the 4 clocks must be present. + - if: + required: + - fsl,common-rxtx-pins + then: + properties: + clocks: + maxItems: 2 + clock-names: + maxItems: 2 + else: + properties: + clocks: + minItems: 4 + clock-names: + minItems: 4 + + required: + - reg + - clocks + - clock-names + +required: + - compatible + - reg + - reg-names + - '#address-cells' + - '#size-cells' + - '#serial-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/fsl,tsa.h> + + tsa@ae0 { + compatible = "fsl,mpc885-tsa", "fsl,cpm1-tsa"; + reg = <0xae0 0x10>, + <0xc00 0x200>; + reg-names = "si_regs", "si_ram"; + + #address-cells = <1>; + #size-cells = <0>; + #serial-cells = <1>; + + tdm@0 { + /* TDMa */ + reg = <0>; + + clocks = <&clk_l1rsynca>, <&clk_l1rclka>; + clock-names = "l1rsync", "l1rclk"; + + fsl,common-rxtx-pins; + fsl,fsync-rising-edge; + + fsl,tx-ts-routes = < 2 0 >, /* TS 0..1 */ + < 24 FSL_CPM_TSA_SCC4 >, /* TS 2..25 */ + < 1 0 >, /* TS 26 */ + < 5 FSL_CPM_TSA_SCC3 >; /* TS 27..31 */ + + fsl,rx-ts-routes = < 2 0 >, /* TS 0..1 */ + < 24 FSL_CPM_TSA_SCC4 >, /* 2..25 */ + < 1 0 >, /* TS 26 */ + < 5 FSL_CPM_TSA_SCC3 >; /* TS 27..31 */ + }; + }; diff --git a/include/dt-bindings/soc/fsl,tsa.h b/include/dt-bindings/soc/fsl,tsa.h new file mode 100644 index 000000000000..2cc44e867dbe --- /dev/null +++ b/include/dt-bindings/soc/fsl,tsa.h @@ -0,0 +1,13 @@ +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ + +#ifndef __DT_BINDINGS_SOC_FSL_TSA_H +#define __DT_BINDINGS_SOC_FSL_TSA_H + +#define FSL_CPM_TSA_NU 0 /* Pseuso Cell Id for not used item */ +#define FSL_CPM_TSA_SCC2 1 +#define FSL_CPM_TSA_SCC3 2 +#define FSL_CPM_TSA_SCC4 3 +#define FSL_CPM_TSA_SMC1 4 +#define FSL_CPM_TSA_SMC2 5 + +#endif
Add support for the time slot assigner (TSA) available in some PowerQUICC SoC such as MPC885 or MPC866. Signed-off-by: Herve Codina <herve.codina@bootlin.com> --- .../bindings/soc/fsl/cpm_qe/fsl,tsa.yaml | 261 ++++++++++++++++++ include/dt-bindings/soc/fsl,tsa.h | 13 + 2 files changed, 274 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/fsl/cpm_qe/fsl,tsa.yaml create mode 100644 include/dt-bindings/soc/fsl,tsa.h