| Message ID | 20230125104520.89684-10-quic_kathirav@quicinc.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
| Series | Add minimal boot support for IPQ5332 | expand |
On 25/01/2023 11:45, Kathiravan Thirumoorthy wrote: > From: Kathiravan T <quic_kathirav@quicinc.com> > > Add initial device tree support for the Qualcomm IPQ5332 SoC and > MI01.2 board. > > Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 71 +++++ > arch/arm64/boot/dts/qcom/ipq5332.dtsi | 273 ++++++++++++++++++++ > 3 files changed, 345 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts > create mode 100644 arch/arm64/boot/dts/qcom/ipq5332.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 3e79496292e7..fbd5bc583a9b 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb > +dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb > diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts > new file mode 100644 > index 000000000000..7984d8f824ce > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts > @@ -0,0 +1,71 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) A bit odd license (accepting GPLv3...), especially that DTSI is only BSD. Was it really intended? > +/* > + * IPQ5332 AP-MI01.2 board device tree source > + * > + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. > + */ > + > +/dts-v1/; > + > +#include "ipq5332.dtsi" > + > +/ { > + model = "Qualcomm Technologies, Inc. IPQ5332/AP-MI01.2"; Just to be clear - you indicated in bindings that "AP" is the foundry ID. This is correct, right? Then I am not sure if it should be in model name. > + compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332"; > + > + aliases { > + serial0 = &blsp1_uart0; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > +}; > + > +&blsp1_uart0 { > + pinctrl-0 = <&serial_0_pins>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&sdhc { > + pinctrl-0 = <&sdc_default_state>; > + pinctrl-names = "default"; > + non-removable; > + status = "okay"; > +}; > + > +&sleep_clk { > + clock-frequency = <32000>; > +}; > + > +&xo_board { > + clock-frequency = <24000000>; > +}; > + > +/* PINCTRL */ > + > +&tlmm { > + sdc_default_state: sdc-default-state { > + clk-pins { > + pins = "gpio13"; > + function = "sdc_clk"; > + drive-strength = <8>; > + bias-disable; > + }; > + > + cmd-pins { > + pins = "gpio12"; > + function = "sdc_cmd"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + data-pins { > + pins = "gpio8", "gpio9", "gpio10", "gpio11"; > + function = "sdc_data"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + }; > +}; > diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi > new file mode 100644 > index 000000000000..d04244a3cd3a > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi > @@ -0,0 +1,273 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * IPQ5332 device tree source > + * > + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. > + */ > + > +#include <dt-bindings/clock/qcom,gcc-ipq5332.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > + > +/ { > + interrupt-parent = <&intc>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + clocks { > + sleep_clk: sleep-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + }; > + > + xo_board: xo-board-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + }; > + }; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + > + CPU0: cpu@0 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x0>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + CPU1: cpu@1 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x1>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + CPU2: cpu@2 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x2>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + CPU3: cpu@3 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x3>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + L2_0: l2-cache { > + compatible = "cache"; > + cache-level = <0x2>; This is just "2", not hex. > + }; > + }; > + > + firmware { > + scm { > + compatible = "qcom,scm-ipq5332", "qcom,scm"; > + }; > + }; > + > + memory@40000000 { > + device_type = "memory"; > + /* We expect the bootloader to fill in the size */ > + reg = <0x0 0x40000000 0x0 0x0>; > + }; > + > + pmu { > + compatible = "arm,cortex-a53-pmu"; > + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + tz: memory@4a600000 { > + no-map; > + reg = <0x0 0x4a600000 0x0 0x200000>; > + }; > + }; > + > + soc@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0 0 0xffffffff>; > + compatible = "simple-bus"; > + > + tlmm: pinctrl@1000000 { > + compatible = "qcom,ipq5332-tlmm"; > + reg = <0x01000000 0x300000>; > + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&tlmm 0 0 53>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > + serial_0_pins: serial0-state { > + pins = "gpio18", "gpio19"; > + function = "blsp0_uart0"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + }; > + > + gcc: clock-controller@1800000 { > + compatible = "qcom,ipq5332-gcc"; > + reg = <0x01800000 0x80000>; > + #clock-cells = <0x1>; > + #reset-cells = <0x1>; > + #power-domain-cells = <1>; > + clock-names = "xo", > + "sleep_clk", > + "pcie_2lane_phy_pipe_clk", > + "pcie_2lane_phy_pipe_clk_x1", > + "usb_pcie_wrapper_pipe_clk"; > + clocks = <&xo_board>, > + <&sleep_clk>, > + <0>, > + <0>, > + <0>; > + }; > + > + sdhc: mmc@7804000 { > + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; > + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; > + > + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > + <&gcc GCC_SDCC1_APPS_CLK>, > + <&xo_board>; > + clock-names = "iface", "core", "xo"; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + max-frequency = <192000000>; > + bus-width = <4>; Aren't these five properties of the board? Do you fix the exact eMMC module inside the SoC? > + status = "disabled"; > + }; > + > + blsp1_uart0: serial@78af000 { > + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; > + reg = <0x078af000 0x200>; > + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, > + <&gcc GCC_BLSP1_AHB_CLK>; > + clock-names = "core", "iface"; > + status = "disabled"; > + }; > + > + intc: interrupt-controller@b000000 { > + compatible = "qcom,msm-qgic2"; > + #address-cells = <1>; > + #size-cells = <1>; > + interrupt-controller; > + #interrupt-cells = <0x3>; > + reg = <0x0b000000 0x1000>, /* GICD */ > + <0x0b002000 0x1000>, /* GICC */ > + <0x0b001000 0x1000>, /* GICH */ > + <0x0b004000 0x1000>; /* GICV */ > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > + ranges = <0 0x0b00c000 0x3000>; > + > + v2m0: v2m@0 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x0 0xffd>; > + msi-controller; > + }; > + > + v2m1: v2m@1 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00001000 0xffd>; > + msi-controller; > + }; > + > + v2m2: v2m@2 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00002000 0xffd>; > + msi-controller; > + }; > + }; > + > + timer@b120000 { > + compatible = "arm,armv7-timer-mem"; > + reg = <0x0b120000 0x1000>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + frame@b120000 { > + frame-number = <0>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b121000 0x1000>, > + <0x0b122000 0x1000>; > + }; > + > + frame@b123000 { > + frame-number = <1>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b123000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b124000 { > + frame-number = <2>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b124000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b125000 { > + frame-number = <3>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b125000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b126000 { > + frame-number = <4>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b126000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b127000 { > + frame-number = <5>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b127000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b128000 { > + frame-number = <6>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b128000 0x1000>; > + status = "disabled"; > + }; > + }; > + Drop blank line. > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; > + }; > +}; Best regards, Krzysztof
On 1/25/2023 4:52 PM, Krzysztof Kozlowski wrote: > On 25/01/2023 11:45, Kathiravan Thirumoorthy wrote: >> From: Kathiravan T <quic_kathirav@quicinc.com> >> >> Add initial device tree support for the Qualcomm IPQ5332 SoC and >> MI01.2 board. >> >> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> >> --- >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 71 +++++ >> arch/arm64/boot/dts/qcom/ipq5332.dtsi | 273 ++++++++++++++++++++ >> 3 files changed, 345 insertions(+) >> create mode 100644 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >> create mode 100644 arch/arm64/boot/dts/qcom/ipq5332.dtsi >> >> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile >> index 3e79496292e7..fbd5bc583a9b 100644 >> --- a/arch/arm64/boot/dts/qcom/Makefile >> +++ b/arch/arm64/boot/dts/qcom/Makefile >> @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb >> +dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb >> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >> new file mode 100644 >> index 000000000000..7984d8f824ce >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >> @@ -0,0 +1,71 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) > A bit odd license (accepting GPLv3...), especially that DTSI is only > BSD. Was it really intended? No, it is not intentional. Will change it to BSD-3-Clause in V2. > >> +/* >> + * IPQ5332 AP-MI01.2 board device tree source >> + * >> + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. >> + */ >> + >> +/dts-v1/; >> + >> +#include "ipq5332.dtsi" >> + >> +/ { >> + model = "Qualcomm Technologies, Inc. IPQ5332/AP-MI01.2"; > Just to be clear - you indicated in bindings that "AP" is the foundry > ID. This is correct, right? Then I am not sure if it should be in model > name. Okay, will change the model to "Qualcomm Technologies, Inc. IPQ5332 MI01.2". I see all other IPQ DTS carries the same naming convention. May be those also should be fixed. > >> + compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332"; >> + >> + aliases { >> + serial0 = &blsp1_uart0; >> + }; >> + >> + chosen { >> + stdout-path = "serial0"; >> + }; >> +}; >> + >> +&blsp1_uart0 { >> + pinctrl-0 = <&serial_0_pins>; >> + pinctrl-names = "default"; >> + status = "okay"; >> +}; >> + >> +&sdhc { >> + pinctrl-0 = <&sdc_default_state>; >> + pinctrl-names = "default"; >> + non-removable; >> + status = "okay"; >> +}; >> + >> +&sleep_clk { >> + clock-frequency = <32000>; >> +}; >> + >> +&xo_board { >> + clock-frequency = <24000000>; >> +}; >> + >> +/* PINCTRL */ >> + >> +&tlmm { >> + sdc_default_state: sdc-default-state { >> + clk-pins { >> + pins = "gpio13"; >> + function = "sdc_clk"; >> + drive-strength = <8>; >> + bias-disable; >> + }; >> + >> + cmd-pins { >> + pins = "gpio12"; >> + function = "sdc_cmd"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + >> + data-pins { >> + pins = "gpio8", "gpio9", "gpio10", "gpio11"; >> + function = "sdc_data"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + }; >> +}; >> diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi >> new file mode 100644 >> index 000000000000..d04244a3cd3a >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi >> @@ -0,0 +1,273 @@ >> +// SPDX-License-Identifier: BSD-3-Clause >> +/* >> + * IPQ5332 device tree source >> + * >> + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. >> + */ >> + >> +#include <dt-bindings/clock/qcom,gcc-ipq5332.h> >> +#include <dt-bindings/interrupt-controller/arm-gic.h> >> + >> +/ { >> + interrupt-parent = <&intc>; >> + #address-cells = <2>; >> + #size-cells = <2>; >> + >> + clocks { >> + sleep_clk: sleep-clk { >> + compatible = "fixed-clock"; >> + #clock-cells = <0>; >> + }; >> + >> + xo_board: xo-board-clk { >> + compatible = "fixed-clock"; >> + #clock-cells = <0>; >> + }; >> + }; >> + >> + cpus { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + CPU0: cpu@0 { >> + device_type = "cpu"; >> + compatible = "arm,cortex-a53"; >> + reg = <0x0>; >> + enable-method = "psci"; >> + next-level-cache = <&L2_0>; >> + }; >> + >> + CPU1: cpu@1 { >> + device_type = "cpu"; >> + compatible = "arm,cortex-a53"; >> + reg = <0x1>; >> + enable-method = "psci"; >> + next-level-cache = <&L2_0>; >> + }; >> + >> + CPU2: cpu@2 { >> + device_type = "cpu"; >> + compatible = "arm,cortex-a53"; >> + reg = <0x2>; >> + enable-method = "psci"; >> + next-level-cache = <&L2_0>; >> + }; >> + >> + CPU3: cpu@3 { >> + device_type = "cpu"; >> + compatible = "arm,cortex-a53"; >> + reg = <0x3>; >> + enable-method = "psci"; >> + next-level-cache = <&L2_0>; >> + }; >> + >> + L2_0: l2-cache { >> + compatible = "cache"; >> + cache-level = <0x2>; > This is just "2", not hex. Ack. > >> + }; >> + }; >> + >> + firmware { >> + scm { >> + compatible = "qcom,scm-ipq5332", "qcom,scm"; >> + }; >> + }; >> + >> + memory@40000000 { >> + device_type = "memory"; >> + /* We expect the bootloader to fill in the size */ >> + reg = <0x0 0x40000000 0x0 0x0>; >> + }; >> + >> + pmu { >> + compatible = "arm,cortex-a53-pmu"; >> + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; >> + }; >> + >> + psci { >> + compatible = "arm,psci-1.0"; >> + method = "smc"; >> + }; >> + >> + reserved-memory { >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges; >> + >> + tz: memory@4a600000 { >> + no-map; >> + reg = <0x0 0x4a600000 0x0 0x200000>; >> + }; >> + }; >> + >> + soc@0 { >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0 0 0 0xffffffff>; >> + compatible = "simple-bus"; >> + >> + tlmm: pinctrl@1000000 { >> + compatible = "qcom,ipq5332-tlmm"; >> + reg = <0x01000000 0x300000>; >> + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + gpio-ranges = <&tlmm 0 0 53>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + >> + serial_0_pins: serial0-state { >> + pins = "gpio18", "gpio19"; >> + function = "blsp0_uart0"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + }; >> + >> + gcc: clock-controller@1800000 { >> + compatible = "qcom,ipq5332-gcc"; >> + reg = <0x01800000 0x80000>; >> + #clock-cells = <0x1>; >> + #reset-cells = <0x1>; >> + #power-domain-cells = <1>; >> + clock-names = "xo", >> + "sleep_clk", >> + "pcie_2lane_phy_pipe_clk", >> + "pcie_2lane_phy_pipe_clk_x1", >> + "usb_pcie_wrapper_pipe_clk"; >> + clocks = <&xo_board>, >> + <&sleep_clk>, >> + <0>, >> + <0>, >> + <0>; >> + }; >> + >> + sdhc: mmc@7804000 { >> + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; >> + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; >> + >> + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names = "hc_irq", "pwr_irq"; >> + >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, >> + <&gcc GCC_SDCC1_APPS_CLK>, >> + <&xo_board>; >> + clock-names = "iface", "core", "xo"; >> + mmc-ddr-1_8v; >> + mmc-hs200-1_8v; >> + max-frequency = <192000000>; >> + bus-width = <4>; > Aren't these five properties of the board? Do you fix the exact eMMC > module inside the SoC? Okay, will cross check this and update it. > >> + status = "disabled"; >> + }; >> + >> + blsp1_uart0: serial@78af000 { >> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; >> + reg = <0x078af000 0x200>; >> + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, >> + <&gcc GCC_BLSP1_AHB_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; >> + }; >> + >> + intc: interrupt-controller@b000000 { >> + compatible = "qcom,msm-qgic2"; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + interrupt-controller; >> + #interrupt-cells = <0x3>; >> + reg = <0x0b000000 0x1000>, /* GICD */ >> + <0x0b002000 0x1000>, /* GICC */ >> + <0x0b001000 0x1000>, /* GICH */ >> + <0x0b004000 0x1000>; /* GICV */ >> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; >> + ranges = <0 0x0b00c000 0x3000>; >> + >> + v2m0: v2m@0 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x0 0xffd>; >> + msi-controller; >> + }; >> + >> + v2m1: v2m@1 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00001000 0xffd>; >> + msi-controller; >> + }; >> + >> + v2m2: v2m@2 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00002000 0xffd>; >> + msi-controller; >> + }; >> + }; >> + >> + timer@b120000 { >> + compatible = "arm,armv7-timer-mem"; >> + reg = <0x0b120000 0x1000>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + >> + frame@b120000 { >> + frame-number = <0>; >> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b121000 0x1000>, >> + <0x0b122000 0x1000>; >> + }; >> + >> + frame@b123000 { >> + frame-number = <1>; >> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b123000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b124000 { >> + frame-number = <2>; >> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b124000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b125000 { >> + frame-number = <3>; >> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b125000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b126000 { >> + frame-number = <4>; >> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b126000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b127000 { >> + frame-number = <5>; >> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b127000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b128000 { >> + frame-number = <6>; >> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b128000 0x1000>; >> + status = "disabled"; >> + }; >> + }; >> + > Drop blank line. Ack. > >> + }; >> + >> + timer { >> + compatible = "arm,armv8-timer"; >> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; >> + }; >> +}; > Best regards, > Krzysztof Thanks, Kathiravan T.
On 25.01.2023 11:45, Kathiravan Thirumoorthy wrote: > From: Kathiravan T <quic_kathirav@quicinc.com> > > Add initial device tree support for the Qualcomm IPQ5332 SoC and > MI01.2 board. > > Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 71 +++++ > arch/arm64/boot/dts/qcom/ipq5332.dtsi | 273 ++++++++++++++++++++ > 3 files changed, 345 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts > create mode 100644 arch/arm64/boot/dts/qcom/ipq5332.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 3e79496292e7..fbd5bc583a9b 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb > dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb > +dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb > dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb > diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts > new file mode 100644 > index 000000000000..7984d8f824ce > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts > @@ -0,0 +1,71 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) > +/* > + * IPQ5332 AP-MI01.2 board device tree source > + * > + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. > + */ > + > +/dts-v1/; > + > +#include "ipq5332.dtsi" > + > +/ { > + model = "Qualcomm Technologies, Inc. IPQ5332/AP-MI01.2"; > + compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332"; > + > + aliases { > + serial0 = &blsp1_uart0; > + }; > + > + chosen { > + stdout-path = "serial0"; > + }; > +}; > + > +&blsp1_uart0 { > + pinctrl-0 = <&serial_0_pins>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&sdhc { > + pinctrl-0 = <&sdc_default_state>; > + pinctrl-names = "default"; > + non-removable; > + status = "okay"; > +}; > + > +&sleep_clk { > + clock-frequency = <32000>; > +}; > + > +&xo_board { > + clock-frequency = <24000000>; > +}; > + > +/* PINCTRL */ > + > +&tlmm { > + sdc_default_state: sdc-default-state { > + clk-pins { > + pins = "gpio13"; > + function = "sdc_clk"; > + drive-strength = <8>; > + bias-disable; > + }; > + > + cmd-pins { > + pins = "gpio12"; > + function = "sdc_cmd"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + > + data-pins { > + pins = "gpio8", "gpio9", "gpio10", "gpio11"; > + function = "sdc_data"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + }; > +}; > diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi > new file mode 100644 > index 000000000000..d04244a3cd3a > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi > @@ -0,0 +1,273 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * IPQ5332 device tree source > + * > + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. > + */ > + > +#include <dt-bindings/clock/qcom,gcc-ipq5332.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > + > +/ { > + interrupt-parent = <&intc>; > + #address-cells = <2>; > + #size-cells = <2>; > + > + clocks { > + sleep_clk: sleep-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + }; > + > + xo_board: xo-board-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + }; > + }; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + > + CPU0: cpu@0 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x0>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + CPU1: cpu@1 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x1>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + CPU2: cpu@2 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x2>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + CPU3: cpu@3 { > + device_type = "cpu"; > + compatible = "arm,cortex-a53"; > + reg = <0x3>; > + enable-method = "psci"; > + next-level-cache = <&L2_0>; > + }; > + > + L2_0: l2-cache { > + compatible = "cache"; > + cache-level = <0x2>; > + }; > + }; > + > + firmware { > + scm { > + compatible = "qcom,scm-ipq5332", "qcom,scm"; > + }; > + }; > + > + memory@40000000 { > + device_type = "memory"; > + /* We expect the bootloader to fill in the size */ > + reg = <0x0 0x40000000 0x0 0x0>; > + }; > + > + pmu { > + compatible = "arm,cortex-a53-pmu"; > + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; > + }; > + > + psci { > + compatible = "arm,psci-1.0"; > + method = "smc"; > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + tz: memory@4a600000 { memory@ is discouraged, the node name should be somewhat descriptive of what lies in this reserved region. On the other hand, tz: sounds like a label to a trust zone device of some kind. I propose: tz_mem: tz@4a600000 { instead. > + no-map; > + reg = <0x0 0x4a600000 0x0 0x200000>; > + }; > + }; > + > + soc@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0 0 0 0xffffffff>; > + compatible = "simple-bus"; Move compatible first, please. > + > + tlmm: pinctrl@1000000 { > + compatible = "qcom,ipq5332-tlmm"; > + reg = <0x01000000 0x300000>; > + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + gpio-ranges = <&tlmm 0 0 53>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > + serial_0_pins: serial0-state { You may be interested in having a suspend state for this one, so you may wish to rename this futureproofing-ly to serial0-active-state. > + pins = "gpio18", "gpio19"; > + function = "blsp0_uart0"; > + drive-strength = <8>; > + bias-pull-up; > + }; > + }; > + > + gcc: clock-controller@1800000 { > + compatible = "qcom,ipq5332-gcc"; > + reg = <0x01800000 0x80000>; > + #clock-cells = <0x1>; > + #reset-cells = <0x1>; Decimal values for -cells, please. > + #power-domain-cells = <1>; > + clock-names = "xo", > + "sleep_clk", > + "pcie_2lane_phy_pipe_clk", > + "pcie_2lane_phy_pipe_clk_x1", > + "usb_pcie_wrapper_pipe_clk"; > + clocks = <&xo_board>, > + <&sleep_clk>, > + <0>, > + <0>, > + <0>; > + }; > + > + sdhc: mmc@7804000 { > + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; > + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; > + > + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > + <&gcc GCC_SDCC1_APPS_CLK>, > + <&xo_board>; > + clock-names = "iface", "core", "xo"; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + max-frequency = <192000000>; As Krzysztof pointed out, this one should go. > + bus-width = <4>; Oh that's interesting.. a 4-wide bus for eMMC? > + status = "disabled"; > + }; > + > + blsp1_uart0: serial@78af000 { > + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; > + reg = <0x078af000 0x200>; > + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, > + <&gcc GCC_BLSP1_AHB_CLK>; > + clock-names = "core", "iface"; > + status = "disabled"; > + }; > + > + intc: interrupt-controller@b000000 { > + compatible = "qcom,msm-qgic2"; > + #address-cells = <1>; > + #size-cells = <1>; Please move these two above ranges.. > + interrupt-controller; > + #interrupt-cells = <0x3>; Decimal value, please. > + reg = <0x0b000000 0x1000>, /* GICD */ > + <0x0b002000 0x1000>, /* GICC */ > + <0x0b001000 0x1000>, /* GICH */ > + <0x0b004000 0x1000>; /* GICV */ ..and reg just below compatible... > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; ..and interrupts just below reg, please. > + ranges = <0 0x0b00c000 0x3000>; > + > + v2m0: v2m@0 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x0 0xffd>; Please pad the reg for consistency. > + msi-controller; > + }; > + > + v2m1: v2m@1 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00001000 0xffd>; > + msi-controller; > + }; > + > + v2m2: v2m@2 { > + compatible = "arm,gic-v2m-frame"; > + reg = <0x00002000 0xffd>; > + msi-controller; > + }; > + }; > + > + timer@b120000 { > + compatible = "arm,armv7-timer-mem"; > + reg = <0x0b120000 0x1000>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + frame@b120000 { > + frame-number = <0>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b121000 0x1000>, > + <0x0b122000 0x1000>; reg interrupts frame-number would be more consistent with most other nodes. > + }; > + > + frame@b123000 { > + frame-number = <1>; > + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b123000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b124000 { > + frame-number = <2>; > + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b124000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b125000 { > + frame-number = <3>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b125000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b126000 { > + frame-number = <4>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b126000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b127000 { > + frame-number = <5>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b127000 0x1000>; > + status = "disabled"; > + }; > + > + frame@b128000 { > + frame-number = <6>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; > + reg = <0x0b128000 0x1000>; > + status = "disabled"; > + }; > + }; > + > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, > + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; The indentation seems off here. Konrad > + }; > +};
Thanks Konrad for taking time to review the patch. On 1/26/2023 3:29 AM, Konrad Dybcio wrote: > > On 25.01.2023 11:45, Kathiravan Thirumoorthy wrote: >> From: Kathiravan T <quic_kathirav@quicinc.com> >> >> Add initial device tree support for the Qualcomm IPQ5332 SoC and >> MI01.2 board. >> >> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> >> --- >> arch/arm64/boot/dts/qcom/Makefile | 1 + >> arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 71 +++++ >> arch/arm64/boot/dts/qcom/ipq5332.dtsi | 273 ++++++++++++++++++++ >> 3 files changed, 345 insertions(+) >> create mode 100644 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >> create mode 100644 arch/arm64/boot/dts/qcom/ipq5332.dtsi >> >> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile >> index 3e79496292e7..fbd5bc583a9b 100644 >> --- a/arch/arm64/boot/dts/qcom/Makefile >> +++ b/arch/arm64/boot/dts/qcom/Makefile >> @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb >> dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb >> +dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb >> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb >> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >> new file mode 100644 >> index 000000000000..7984d8f824ce >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >> @@ -0,0 +1,71 @@ >> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) >> +/* >> + * IPQ5332 AP-MI01.2 board device tree source >> + * >> + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. >> + */ >> + >> +/dts-v1/; >> + >> +#include "ipq5332.dtsi" >> + >> +/ { >> + model = "Qualcomm Technologies, Inc. IPQ5332/AP-MI01.2"; >> + compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332"; >> + >> + aliases { >> + serial0 = &blsp1_uart0; >> + }; >> + >> + chosen { >> + stdout-path = "serial0"; >> + }; >> +}; >> + >> +&blsp1_uart0 { >> + pinctrl-0 = <&serial_0_pins>; >> + pinctrl-names = "default"; >> + status = "okay"; >> +}; >> + >> +&sdhc { >> + pinctrl-0 = <&sdc_default_state>; >> + pinctrl-names = "default"; >> + non-removable; >> + status = "okay"; >> +}; >> + >> +&sleep_clk { >> + clock-frequency = <32000>; >> +}; >> + >> +&xo_board { >> + clock-frequency = <24000000>; >> +}; >> + >> +/* PINCTRL */ >> + >> +&tlmm { >> + sdc_default_state: sdc-default-state { >> + clk-pins { >> + pins = "gpio13"; >> + function = "sdc_clk"; >> + drive-strength = <8>; >> + bias-disable; >> + }; >> + >> + cmd-pins { >> + pins = "gpio12"; >> + function = "sdc_cmd"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + >> + data-pins { >> + pins = "gpio8", "gpio9", "gpio10", "gpio11"; >> + function = "sdc_data"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + }; >> +}; >> diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi >> new file mode 100644 >> index 000000000000..d04244a3cd3a >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi >> @@ -0,0 +1,273 @@ >> +// SPDX-License-Identifier: BSD-3-Clause >> +/* >> + * IPQ5332 device tree source >> + * >> + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. >> + */ >> + >> +#include <dt-bindings/clock/qcom,gcc-ipq5332.h> >> +#include <dt-bindings/interrupt-controller/arm-gic.h> >> + >> +/ { >> + interrupt-parent = <&intc>; >> + #address-cells = <2>; >> + #size-cells = <2>; >> + >> + clocks { >> + sleep_clk: sleep-clk { >> + compatible = "fixed-clock"; >> + #clock-cells = <0>; >> + }; >> + >> + xo_board: xo-board-clk { >> + compatible = "fixed-clock"; >> + #clock-cells = <0>; >> + }; >> + }; >> + >> + cpus { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + CPU0: cpu@0 { >> + device_type = "cpu"; >> + compatible = "arm,cortex-a53"; >> + reg = <0x0>; >> + enable-method = "psci"; >> + next-level-cache = <&L2_0>; >> + }; >> + >> + CPU1: cpu@1 { >> + device_type = "cpu"; >> + compatible = "arm,cortex-a53"; >> + reg = <0x1>; >> + enable-method = "psci"; >> + next-level-cache = <&L2_0>; >> + }; >> + >> + CPU2: cpu@2 { >> + device_type = "cpu"; >> + compatible = "arm,cortex-a53"; >> + reg = <0x2>; >> + enable-method = "psci"; >> + next-level-cache = <&L2_0>; >> + }; >> + >> + CPU3: cpu@3 { >> + device_type = "cpu"; >> + compatible = "arm,cortex-a53"; >> + reg = <0x3>; >> + enable-method = "psci"; >> + next-level-cache = <&L2_0>; >> + }; >> + >> + L2_0: l2-cache { >> + compatible = "cache"; >> + cache-level = <0x2>; >> + }; >> + }; >> + >> + firmware { >> + scm { >> + compatible = "qcom,scm-ipq5332", "qcom,scm"; >> + }; >> + }; >> + >> + memory@40000000 { >> + device_type = "memory"; >> + /* We expect the bootloader to fill in the size */ >> + reg = <0x0 0x40000000 0x0 0x0>; >> + }; >> + >> + pmu { >> + compatible = "arm,cortex-a53-pmu"; >> + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; >> + }; >> + >> + psci { >> + compatible = "arm,psci-1.0"; >> + method = "smc"; >> + }; >> + >> + reserved-memory { >> + #address-cells = <2>; >> + #size-cells = <2>; >> + ranges; >> + >> + tz: memory@4a600000 { > memory@ is discouraged, the node name should be somewhat > descriptive of what lies in this reserved region. On the > other hand, tz: sounds like a label to a trust zone device > of some kind. I propose: > > tz_mem: tz@4a600000 { > > instead. Ack. > >> + no-map; >> + reg = <0x0 0x4a600000 0x0 0x200000>; >> + }; >> + }; >> + >> + soc@0 { >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges = <0 0 0 0xffffffff>; >> + compatible = "simple-bus"; > Move compatible first, please. Ack. > >> + >> + tlmm: pinctrl@1000000 { >> + compatible = "qcom,ipq5332-tlmm"; >> + reg = <0x01000000 0x300000>; >> + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + gpio-ranges = <&tlmm 0 0 53>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + >> + serial_0_pins: serial0-state { > You may be interested in having a suspend state for this > one, so you may wish to rename this futureproofing-ly to > serial0-active-state. Ack. AFAIK, we don't support suspend state, anyways let me got back and check it. > >> + pins = "gpio18", "gpio19"; >> + function = "blsp0_uart0"; >> + drive-strength = <8>; >> + bias-pull-up; >> + }; >> + }; >> + >> + gcc: clock-controller@1800000 { >> + compatible = "qcom,ipq5332-gcc"; >> + reg = <0x01800000 0x80000>; >> + #clock-cells = <0x1>; >> + #reset-cells = <0x1>; > Decimal values for -cells, please. Ack. > >> + #power-domain-cells = <1>; >> + clock-names = "xo", >> + "sleep_clk", >> + "pcie_2lane_phy_pipe_clk", >> + "pcie_2lane_phy_pipe_clk_x1", >> + "usb_pcie_wrapper_pipe_clk"; >> + clocks = <&xo_board>, >> + <&sleep_clk>, >> + <0>, >> + <0>, >> + <0>; >> + }; >> + >> + sdhc: mmc@7804000 { >> + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; >> + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; >> + >> + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names = "hc_irq", "pwr_irq"; >> + >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, >> + <&gcc GCC_SDCC1_APPS_CLK>, >> + <&xo_board>; >> + clock-names = "iface", "core", "xo"; >> + mmc-ddr-1_8v; >> + mmc-hs200-1_8v; >> + max-frequency = <192000000>; > As Krzysztof pointed out, this one should go. Ack. > >> + bus-width = <4>; > Oh that's interesting.. a 4-wide bus for eMMC? Yes, eMMC is 4bit bus width with HS200 mode only. > >> + status = "disabled"; >> + }; >> + >> + blsp1_uart0: serial@78af000 { >> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; >> + reg = <0x078af000 0x200>; >> + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, >> + <&gcc GCC_BLSP1_AHB_CLK>; >> + clock-names = "core", "iface"; >> + status = "disabled"; >> + }; >> + >> + intc: interrupt-controller@b000000 { >> + compatible = "qcom,msm-qgic2"; >> + #address-cells = <1>; >> + #size-cells = <1>; > Please move these two above ranges.. Ack. > >> + interrupt-controller; >> + #interrupt-cells = <0x3>; > Decimal value, please. Ack. > >> + reg = <0x0b000000 0x1000>, /* GICD */ >> + <0x0b002000 0x1000>, /* GICC */ >> + <0x0b001000 0x1000>, /* GICH */ >> + <0x0b004000 0x1000>; /* GICV */ > ..and reg just below compatible... Ack. > >> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; > ..and interrupts just below reg, please. Ack. > >> + ranges = <0 0x0b00c000 0x3000>; >> + >> + v2m0: v2m@0 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x0 0xffd>; > Please pad the reg for consistency. Sure. >> + msi-controller; >> + }; >> + >> + v2m1: v2m@1 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00001000 0xffd>; >> + msi-controller; >> + }; >> + >> + v2m2: v2m@2 { >> + compatible = "arm,gic-v2m-frame"; >> + reg = <0x00002000 0xffd>; >> + msi-controller; >> + }; >> + }; >> + >> + timer@b120000 { >> + compatible = "arm,armv7-timer-mem"; >> + reg = <0x0b120000 0x1000>; >> + #address-cells = <1>; >> + #size-cells = <1>; >> + ranges; >> + >> + frame@b120000 { >> + frame-number = <0>; >> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b121000 0x1000>, >> + <0x0b122000 0x1000>; > reg > interrupts > frame-number > > would be more consistent with most other nodes. Ack. > >> + }; >> + >> + frame@b123000 { >> + frame-number = <1>; >> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b123000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b124000 { >> + frame-number = <2>; >> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b124000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b125000 { >> + frame-number = <3>; >> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b125000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b126000 { >> + frame-number = <4>; >> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b126000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b127000 { >> + frame-number = <5>; >> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b127000 0x1000>; >> + status = "disabled"; >> + }; >> + >> + frame@b128000 { >> + frame-number = <6>; >> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; >> + reg = <0x0b128000 0x1000>; >> + status = "disabled"; >> + }; >> + }; >> + >> + }; >> + >> + timer { >> + compatible = "arm,armv8-timer"; >> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, >> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; > The indentation seems off here. Will fix it in V2. Thanks. > > Konrad >> + }; >> +};
On 1/26/2023 10:20 PM, Kathiravan Thirumoorthy wrote: > Thanks Konrad for taking time to review the patch. > > > On 1/26/2023 3:29 AM, Konrad Dybcio wrote: >> >> On 25.01.2023 11:45, Kathiravan Thirumoorthy wrote: >>> From: Kathiravan T <quic_kathirav@quicinc.com> >>> >>> Add initial device tree support for the Qualcomm IPQ5332 SoC and >>> MI01.2 board. >>> >>> Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com> >>> --- >>> arch/arm64/boot/dts/qcom/Makefile | 1 + >>> arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts | 71 +++++ >>> arch/arm64/boot/dts/qcom/ipq5332.dtsi | 273 >>> ++++++++++++++++++++ >>> 3 files changed, 345 insertions(+) >>> create mode 100644 arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >>> create mode 100644 arch/arm64/boot/dts/qcom/ipq5332.dtsi >>> >>> diff --git a/arch/arm64/boot/dts/qcom/Makefile >>> b/arch/arm64/boot/dts/qcom/Makefile >>> index 3e79496292e7..fbd5bc583a9b 100644 >>> --- a/arch/arm64/boot/dts/qcom/Makefile >>> +++ b/arch/arm64/boot/dts/qcom/Makefile >>> @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb >>> dtb-$(CONFIG_ARCH_QCOM) += >>> apq8094-sony-xperia-kitakami-karin_windy.dtb >>> dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb >>> dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb >>> +dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb >>> dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb >>> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb >>> dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb >>> diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >>> b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >>> new file mode 100644 >>> index 000000000000..7984d8f824ce >>> --- /dev/null >>> +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts >>> @@ -0,0 +1,71 @@ >>> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) >>> +/* >>> + * IPQ5332 AP-MI01.2 board device tree source >>> + * >>> + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All >>> rights reserved. >>> + */ >>> + >>> +/dts-v1/; >>> + >>> +#include "ipq5332.dtsi" >>> + >>> +/ { >>> + model = "Qualcomm Technologies, Inc. IPQ5332/AP-MI01.2"; >>> + compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332"; >>> + >>> + aliases { >>> + serial0 = &blsp1_uart0; >>> + }; >>> + >>> + chosen { >>> + stdout-path = "serial0"; >>> + }; >>> +}; >>> + >>> +&blsp1_uart0 { >>> + pinctrl-0 = <&serial_0_pins>; >>> + pinctrl-names = "default"; >>> + status = "okay"; >>> +}; >>> + >>> +&sdhc { >>> + pinctrl-0 = <&sdc_default_state>; >>> + pinctrl-names = "default"; >>> + non-removable; >>> + status = "okay"; >>> +}; >>> + >>> +&sleep_clk { >>> + clock-frequency = <32000>; >>> +}; >>> + >>> +&xo_board { >>> + clock-frequency = <24000000>; >>> +}; >>> + >>> +/* PINCTRL */ >>> + >>> +&tlmm { >>> + sdc_default_state: sdc-default-state { >>> + clk-pins { >>> + pins = "gpio13"; >>> + function = "sdc_clk"; >>> + drive-strength = <8>; >>> + bias-disable; >>> + }; >>> + >>> + cmd-pins { >>> + pins = "gpio12"; >>> + function = "sdc_cmd"; >>> + drive-strength = <8>; >>> + bias-pull-up; >>> + }; >>> + >>> + data-pins { >>> + pins = "gpio8", "gpio9", "gpio10", "gpio11"; >>> + function = "sdc_data"; >>> + drive-strength = <8>; >>> + bias-pull-up; >>> + }; >>> + }; >>> +}; >>> diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi >>> b/arch/arm64/boot/dts/qcom/ipq5332.dtsi >>> new file mode 100644 >>> index 000000000000..d04244a3cd3a >>> --- /dev/null >>> +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi >>> @@ -0,0 +1,273 @@ >>> +// SPDX-License-Identifier: BSD-3-Clause >>> +/* >>> + * IPQ5332 device tree source >>> + * >>> + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All >>> rights reserved. >>> + */ >>> + >>> +#include <dt-bindings/clock/qcom,gcc-ipq5332.h> >>> +#include <dt-bindings/interrupt-controller/arm-gic.h> >>> + >>> +/ { >>> + interrupt-parent = <&intc>; >>> + #address-cells = <2>; >>> + #size-cells = <2>; >>> + >>> + clocks { >>> + sleep_clk: sleep-clk { >>> + compatible = "fixed-clock"; >>> + #clock-cells = <0>; >>> + }; >>> + >>> + xo_board: xo-board-clk { >>> + compatible = "fixed-clock"; >>> + #clock-cells = <0>; >>> + }; >>> + }; >>> + >>> + cpus { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + CPU0: cpu@0 { >>> + device_type = "cpu"; >>> + compatible = "arm,cortex-a53"; >>> + reg = <0x0>; >>> + enable-method = "psci"; >>> + next-level-cache = <&L2_0>; >>> + }; >>> + >>> + CPU1: cpu@1 { >>> + device_type = "cpu"; >>> + compatible = "arm,cortex-a53"; >>> + reg = <0x1>; >>> + enable-method = "psci"; >>> + next-level-cache = <&L2_0>; >>> + }; >>> + >>> + CPU2: cpu@2 { >>> + device_type = "cpu"; >>> + compatible = "arm,cortex-a53"; >>> + reg = <0x2>; >>> + enable-method = "psci"; >>> + next-level-cache = <&L2_0>; >>> + }; >>> + >>> + CPU3: cpu@3 { >>> + device_type = "cpu"; >>> + compatible = "arm,cortex-a53"; >>> + reg = <0x3>; >>> + enable-method = "psci"; >>> + next-level-cache = <&L2_0>; >>> + }; >>> + >>> + L2_0: l2-cache { >>> + compatible = "cache"; >>> + cache-level = <0x2>; >>> + }; >>> + }; >>> + >>> + firmware { >>> + scm { >>> + compatible = "qcom,scm-ipq5332", "qcom,scm"; >>> + }; >>> + }; >>> + >>> + memory@40000000 { >>> + device_type = "memory"; >>> + /* We expect the bootloader to fill in the size */ >>> + reg = <0x0 0x40000000 0x0 0x0>; >>> + }; >>> + >>> + pmu { >>> + compatible = "arm,cortex-a53-pmu"; >>> + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | >>> IRQ_TYPE_LEVEL_HIGH)>; >>> + }; >>> + >>> + psci { >>> + compatible = "arm,psci-1.0"; >>> + method = "smc"; >>> + }; >>> + >>> + reserved-memory { >>> + #address-cells = <2>; >>> + #size-cells = <2>; >>> + ranges; >>> + >>> + tz: memory@4a600000 { >> memory@ is discouraged, the node name should be somewhat >> descriptive of what lies in this reserved region. On the >> other hand, tz: sounds like a label to a trust zone device >> of some kind. I propose: >> >> tz_mem: tz@4a600000 { >> >> instead. > > > Ack. > > >> >>> + no-map; >>> + reg = <0x0 0x4a600000 0x0 0x200000>; >>> + }; >>> + }; >>> + >>> + soc@0 { >>> + #address-cells = <1>; >>> + #size-cells = <1>; >>> + ranges = <0 0 0 0xffffffff>; >>> + compatible = "simple-bus"; >> Move compatible first, please. > > > Ack. > > >> >>> + >>> + tlmm: pinctrl@1000000 { >>> + compatible = "qcom,ipq5332-tlmm"; >>> + reg = <0x01000000 0x300000>; >>> + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; >>> + gpio-controller; >>> + #gpio-cells = <2>; >>> + gpio-ranges = <&tlmm 0 0 53>; >>> + interrupt-controller; >>> + #interrupt-cells = <2>; >>> + >>> + serial_0_pins: serial0-state { >> You may be interested in having a suspend state for this >> one, so you may wish to rename this futureproofing-ly to >> serial0-active-state. > > > Ack. AFAIK, we don't support suspend state, anyways let me got back > and check it. Konrad, we don't support the suspend state for the console UART, so left the node name as it is in V2. > > >> >>> + pins = "gpio18", "gpio19"; >>> + function = "blsp0_uart0"; >>> + drive-strength = <8>; >>> + bias-pull-up; >>> + }; >>> + }; >>> + >>> + gcc: clock-controller@1800000 { >>> + compatible = "qcom,ipq5332-gcc"; >>> + reg = <0x01800000 0x80000>; >>> + #clock-cells = <0x1>; >>> + #reset-cells = <0x1>; >> Decimal values for -cells, please. > > > Ack. > > >> >>> + #power-domain-cells = <1>; >>> + clock-names = "xo", >>> + "sleep_clk", >>> + "pcie_2lane_phy_pipe_clk", >>> + "pcie_2lane_phy_pipe_clk_x1", >>> + "usb_pcie_wrapper_pipe_clk"; >>> + clocks = <&xo_board>, >>> + <&sleep_clk>, >>> + <0>, >>> + <0>, >>> + <0>; >>> + }; >>> + >>> + sdhc: mmc@7804000 { >>> + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; >>> + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; >>> + >>> + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, >>> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; >>> + interrupt-names = "hc_irq", "pwr_irq"; >>> + >>> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, >>> + <&gcc GCC_SDCC1_APPS_CLK>, >>> + <&xo_board>; >>> + clock-names = "iface", "core", "xo"; >>> + mmc-ddr-1_8v; >>> + mmc-hs200-1_8v; >>> + max-frequency = <192000000>; >> As Krzysztof pointed out, this one should go. > > > Ack. Krzysztof & Konrad, These are the properties of the SDHC controller present in the SoC. So I think no need to move out these properties to board DTS. Please let me know if my understanding is otherwise. > > >> >>> + bus-width = <4>; >> Oh that's interesting.. a 4-wide bus for eMMC? > > > Yes, eMMC is 4bit bus width with HS200 mode only. > > >> >>> + status = "disabled"; >>> + }; >>> + >>> + blsp1_uart0: serial@78af000 { >>> + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; >>> + reg = <0x078af000 0x200>; >>> + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; >>> + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, >>> + <&gcc GCC_BLSP1_AHB_CLK>; >>> + clock-names = "core", "iface"; >>> + status = "disabled"; >>> + }; >>> + >>> + intc: interrupt-controller@b000000 { >>> + compatible = "qcom,msm-qgic2"; >>> + #address-cells = <1>; >>> + #size-cells = <1>; >> Please move these two above ranges.. > > > Ack. > > >> >>> + interrupt-controller; >>> + #interrupt-cells = <0x3>; >> Decimal value, please. > > > Ack. > > >> >>> + reg = <0x0b000000 0x1000>, /* GICD */ >>> + <0x0b002000 0x1000>, /* GICC */ >>> + <0x0b001000 0x1000>, /* GICH */ >>> + <0x0b004000 0x1000>; /* GICV */ >> ..and reg just below compatible... > > Ack. > > >> >>> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; >> ..and interrupts just below reg, please. > > Ack. > > >> >>> + ranges = <0 0x0b00c000 0x3000>; >>> + >>> + v2m0: v2m@0 { >>> + compatible = "arm,gic-v2m-frame"; >>> + reg = <0x0 0xffd>; >> Please pad the reg for consistency. > > > Sure. > > >>> + msi-controller; >>> + }; >>> + >>> + v2m1: v2m@1 { >>> + compatible = "arm,gic-v2m-frame"; >>> + reg = <0x00001000 0xffd>; >>> + msi-controller; >>> + }; >>> + >>> + v2m2: v2m@2 { >>> + compatible = "arm,gic-v2m-frame"; >>> + reg = <0x00002000 0xffd>; >>> + msi-controller; >>> + }; >>> + }; >>> + >>> + timer@b120000 { >>> + compatible = "arm,armv7-timer-mem"; >>> + reg = <0x0b120000 0x1000>; >>> + #address-cells = <1>; >>> + #size-cells = <1>; >>> + ranges; >>> + >>> + frame@b120000 { >>> + frame-number = <0>; >>> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, >>> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; >>> + reg = <0x0b121000 0x1000>, >>> + <0x0b122000 0x1000>; >> reg >> interrupts >> frame-number >> >> would be more consistent with most other nodes. > Ack. >> >>> + }; >>> + >>> + frame@b123000 { >>> + frame-number = <1>; >>> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; >>> + reg = <0x0b123000 0x1000>; >>> + status = "disabled"; >>> + }; >>> + >>> + frame@b124000 { >>> + frame-number = <2>; >>> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; >>> + reg = <0x0b124000 0x1000>; >>> + status = "disabled"; >>> + }; >>> + >>> + frame@b125000 { >>> + frame-number = <3>; >>> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; >>> + reg = <0x0b125000 0x1000>; >>> + status = "disabled"; >>> + }; >>> + >>> + frame@b126000 { >>> + frame-number = <4>; >>> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; >>> + reg = <0x0b126000 0x1000>; >>> + status = "disabled"; >>> + }; >>> + >>> + frame@b127000 { >>> + frame-number = <5>; >>> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; >>> + reg = <0x0b127000 0x1000>; >>> + status = "disabled"; >>> + }; >>> + >>> + frame@b128000 { >>> + frame-number = <6>; >>> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; >>> + reg = <0x0b128000 0x1000>; >>> + status = "disabled"; >>> + }; >>> + }; >>> + >>> + }; >>> + >>> + timer { >>> + compatible = "arm,armv8-timer"; >>> + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | >>> IRQ_TYPE_LEVEL_LOW)>, >>> + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | >>> IRQ_TYPE_LEVEL_LOW)>, >>> + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | >>> IRQ_TYPE_LEVEL_LOW)>, >>> + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | >>> IRQ_TYPE_LEVEL_LOW)>; >> The indentation seems off here. > > > Will fix it in V2. Thanks. > > >> >> Konrad >>> + }; >>> +};
On 30/01/2023 12:56, Kathiravan Thirumoorthy wrote: >>>> + sdhc: mmc@7804000 { >>>> + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; >>>> + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; >>>> + >>>> + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, >>>> + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; >>>> + interrupt-names = "hc_irq", "pwr_irq"; >>>> + >>>> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, >>>> + <&gcc GCC_SDCC1_APPS_CLK>, >>>> + <&xo_board>; >>>> + clock-names = "iface", "core", "xo"; >>>> + mmc-ddr-1_8v; >>>> + mmc-hs200-1_8v; >>>> + max-frequency = <192000000>; >>> As Krzysztof pointed out, this one should go. >> >> >> Ack. > > Krzysztof & Konrad, > > These are the properties of the SDHC controller present in the SoC. So I > think no need to move out these properties to board DTS. Please let me > know if my understanding is otherwise. Usually max frequency of SDHC controller is depending on the board, so no, it is not a property of SoC. The same with type of attached memory. Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 3e79496292e7..fbd5bc583a9b 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb +dtb-$(CONFIG_ARCH_QCOM) += ipq5332-mi01.2.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk10-c1.dtb diff --git a/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts new file mode 100644 index 000000000000..7984d8f824ce --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq5332-mi01.2.dts @@ -0,0 +1,71 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * IPQ5332 AP-MI01.2 board device tree source + * + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +/dts-v1/; + +#include "ipq5332.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. IPQ5332/AP-MI01.2"; + compatible = "qcom,ipq5332-ap-mi01.2", "qcom,ipq5332"; + + aliases { + serial0 = &blsp1_uart0; + }; + + chosen { + stdout-path = "serial0"; + }; +}; + +&blsp1_uart0 { + pinctrl-0 = <&serial_0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&sdhc { + pinctrl-0 = <&sdc_default_state>; + pinctrl-names = "default"; + non-removable; + status = "okay"; +}; + +&sleep_clk { + clock-frequency = <32000>; +}; + +&xo_board { + clock-frequency = <24000000>; +}; + +/* PINCTRL */ + +&tlmm { + sdc_default_state: sdc-default-state { + clk-pins { + pins = "gpio13"; + function = "sdc_clk"; + drive-strength = <8>; + bias-disable; + }; + + cmd-pins { + pins = "gpio12"; + function = "sdc_cmd"; + drive-strength = <8>; + bias-pull-up; + }; + + data-pins { + pins = "gpio8", "gpio9", "gpio10", "gpio11"; + function = "sdc_data"; + drive-strength = <8>; + bias-pull-up; + }; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/ipq5332.dtsi b/arch/arm64/boot/dts/qcom/ipq5332.dtsi new file mode 100644 index 000000000000..d04244a3cd3a --- /dev/null +++ b/arch/arm64/boot/dts/qcom/ipq5332.dtsi @@ -0,0 +1,273 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * IPQ5332 device tree source + * + * Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved. + */ + +#include <dt-bindings/clock/qcom,gcc-ipq5332.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + interrupt-parent = <&intc>; + #address-cells = <2>; + #size-cells = <2>; + + clocks { + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + xo_board: xo-board-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x1>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x2>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x3>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + }; + + L2_0: l2-cache { + compatible = "cache"; + cache-level = <0x2>; + }; + }; + + firmware { + scm { + compatible = "qcom,scm-ipq5332", "qcom,scm"; + }; + }; + + memory@40000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x40000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + tz: memory@4a600000 { + no-map; + reg = <0x0 0x4a600000 0x0 0x200000>; + }; + }; + + soc@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + compatible = "simple-bus"; + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq5332-tlmm"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&tlmm 0 0 53>; + interrupt-controller; + #interrupt-cells = <2>; + + serial_0_pins: serial0-state { + pins = "gpio18", "gpio19"; + function = "blsp0_uart0"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + gcc: clock-controller@1800000 { + compatible = "qcom,ipq5332-gcc"; + reg = <0x01800000 0x80000>; + #clock-cells = <0x1>; + #reset-cells = <0x1>; + #power-domain-cells = <1>; + clock-names = "xo", + "sleep_clk", + "pcie_2lane_phy_pipe_clk", + "pcie_2lane_phy_pipe_clk_x1", + "usb_pcie_wrapper_pipe_clk"; + clocks = <&xo_board>, + <&sleep_clk>, + <0>, + <0>, + <0>; + }; + + sdhc: mmc@7804000 { + compatible = "qcom,ipq5332-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x07804000 0x1000>, <0x07805000 0x1000>; + + interrupts = <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>, + <&xo_board>; + clock-names = "iface", "core", "xo"; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <192000000>; + bus-width = <4>; + status = "disabled"; + }; + + blsp1_uart0: serial@78af000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078af000 0x200>; + interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + #address-cells = <1>; + #size-cells = <1>; + interrupt-controller; + #interrupt-cells = <0x3>; + reg = <0x0b000000 0x1000>, /* GICD */ + <0x0b002000 0x1000>, /* GICC */ + <0x0b001000 0x1000>, /* GICH */ + <0x0b004000 0x1000>; /* GICV */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + ranges = <0 0x0b00c000 0x3000>; + + v2m0: v2m@0 { + compatible = "arm,gic-v2m-frame"; + reg = <0x0 0xffd>; + msi-controller; + }; + + v2m1: v2m@1 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00001000 0xffd>; + msi-controller; + }; + + v2m2: v2m@2 { + compatible = "arm,gic-v2m-frame"; + reg = <0x00002000 0xffd>; + msi-controller; + }; + }; + + timer@b120000 { + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + frame@b120000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + }; + + frame@b123000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b123000 0x1000>; + status = "disabled"; + }; + + frame@b124000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b124000 0x1000>; + status = "disabled"; + }; + + frame@b125000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b125000 0x1000>; + status = "disabled"; + }; + + frame@b126000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b126000 0x1000>; + status = "disabled"; + }; + + frame@b127000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b127000 0x1000>; + status = "disabled"; + }; + + frame@b128000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b128000 0x1000>; + status = "disabled"; + }; + }; + + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; +};