| Message ID | 20230206001634.2566-5-steev@kali.org (mailing list archive) |
|---|---|
| State | Awaiting Upstream |
| Headers | show |
| Series | Attempt at adding WCN6855 BT support | expand |
| Context | Check | Description |
|---|---|---|
| netdev/tree_selection | success | Not a local patch |
On Sun, Feb 05, 2023 at 06:16:34PM -0600, Steev Klimaszewski wrote: > --- This marks the end of the commit message, as such your S-o-b is "missing". Move it above the "---" line. It's also recommended to include some body in your commit message. Perhaps just "The ... has a WCN6855 Bluetooth controller on uart2, add this". > Changes since v2: And keep the change log here. > - Remove dead code and add TODO comment > - Make dtbs_check happy with the pin definitions > > Signed-off-by: Steev Klimaszewski <steev@kali.org> > --- > .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 63 +++++++++++++++++++ > 1 file changed, 63 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > index f936b020a71d..d351411d3504 100644 > --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts > @@ -24,6 +24,8 @@ / { > aliases { > i2c4 = &i2c4; > i2c21 = &i2c21; > + serial0 = &uart17; > + serial1 = &uart2; > }; > > wcd938x: audio-codec { > @@ -712,6 +714,27 @@ &qup0 { > status = "okay"; > }; > > +&uart2 { > + status = "okay"; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&uart2_state>; > + > + bluetooth { > + compatible = "qcom,wcn6855-bt"; > + > + /* TODO: define regulators */ You have the list of regulators in the driver, and there are people with the schematics. You should be able to fill this list out. Regards, Bjorn > + > + max-speed = <3200000>; > + > + enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>; > + swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&bt_en>; > + }; > +}; > + > &qup1 { > status = "okay"; > }; > @@ -720,6 +743,12 @@ &qup2 { > status = "okay"; > }; > > +&uart17 { > + compatible = "qcom,geni-debug-uart"; > + > + status = "okay"; > +}; > + > &remoteproc_adsp { > firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn"; > > @@ -980,6 +1009,19 @@ hastings_reg_en: hastings-reg-en-state { > &tlmm { > gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>; > > + bt_en: bt-en-state { > + hstp-sw-ctrl-pins { > + pins = "gpio132"; > + function = "gpio"; > + }; > + > + hstp-bt-en-pins { > + pins = "gpio133"; > + function = "gpio"; > + drive-strength = <16>; > + }; > + }; > + > edp_reg_en: edp-reg-en-state { > pins = "gpio25"; > function = "gpio"; > @@ -1001,6 +1043,27 @@ i2c4_default: i2c4-default-state { > bias-disable; > }; > > + uart2_state: uart2-state { > + cts-pins { > + pins = "gpio122"; > + function = "qup2"; > + bias-disable; > + }; > + > + rts-tx-pins { > + pins = "gpio122", "gpio123"; > + function = "qup2"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + rx-pins { > + pins = "gpio124"; > + function = "qup2"; > + bias-pull-up; > + }; > + }; > + > i2c21_default: i2c21-default-state { > pins = "gpio81", "gpio82"; > function = "qup21"; > -- > 2.39.0 >
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts index f936b020a71d..d351411d3504 100644 --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts @@ -24,6 +24,8 @@ / { aliases { i2c4 = &i2c4; i2c21 = &i2c21; + serial0 = &uart17; + serial1 = &uart2; }; wcd938x: audio-codec { @@ -712,6 +714,27 @@ &qup0 { status = "okay"; }; +&uart2 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&uart2_state>; + + bluetooth { + compatible = "qcom,wcn6855-bt"; + + /* TODO: define regulators */ + + max-speed = <3200000>; + + enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>; + swctrl-gpios = <&tlmm 132 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&bt_en>; + }; +}; + &qup1 { status = "okay"; }; @@ -720,6 +743,12 @@ &qup2 { status = "okay"; }; +&uart17 { + compatible = "qcom,geni-debug-uart"; + + status = "okay"; +}; + &remoteproc_adsp { firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn"; @@ -980,6 +1009,19 @@ hastings_reg_en: hastings-reg-en-state { &tlmm { gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>; + bt_en: bt-en-state { + hstp-sw-ctrl-pins { + pins = "gpio132"; + function = "gpio"; + }; + + hstp-bt-en-pins { + pins = "gpio133"; + function = "gpio"; + drive-strength = <16>; + }; + }; + edp_reg_en: edp-reg-en-state { pins = "gpio25"; function = "gpio"; @@ -1001,6 +1043,27 @@ i2c4_default: i2c4-default-state { bias-disable; }; + uart2_state: uart2-state { + cts-pins { + pins = "gpio122"; + function = "qup2"; + bias-disable; + }; + + rts-tx-pins { + pins = "gpio122", "gpio123"; + function = "qup2"; + drive-strength = <2>; + bias-disable; + }; + + rx-pins { + pins = "gpio124"; + function = "qup2"; + bias-pull-up; + }; + }; + i2c21_default: i2c21-default-state { pins = "gpio81", "gpio82"; function = "qup21";
--- Changes since v2: - Remove dead code and add TODO comment - Make dtbs_check happy with the pin definitions Signed-off-by: Steev Klimaszewski <steev@kali.org> --- .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts | 63 +++++++++++++++++++ 1 file changed, 63 insertions(+)