| Message ID | 20230303-topic-amlogic-upstream-bpi-cm4-v1-2-5a23a1ade6bd@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: amlogic: Add initial support for BPI-CM4 module with BPI-CM4IO baseboard | expand |
Resending from an email account that doesn’t get rejected by all the lists. Apologies if you did get this twice: > On 3 Mar 2023, at 9:37 pm, Neil Armstrong <neil.armstrong@linaro.org> wrote: > > Add support for both the BananaPi BPI-CM4 module and the BananaPi > baseboard which is comnpatible with the RaspberryPi CM4IO baseboard. > > The BananaPi BPI-CM4 module follows the CM4 specifications at [1], > but with a single HDMI port and a since DSI output. > > The current CM4IO baseboard DT should work fine on the Raspberry CM4 > baseboard and other derivatives baseboards, but proper DT should > be written for other baseboards. > > The split is done so it's easy to describe a new CM4 baseboard, enabling > only the necessary HW used on the baseboard. > > [1] https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf > > Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> > --- > arch/arm64/boot/dts/amlogic/Makefile | 1 + > .../dts/amlogic/meson-g12b-bananapi-cm4-cm4io.dts | 165 +++++++++ > .../boot/dts/amlogic/meson-g12b-bananapi-cm4.dtsi | 388 +++++++++++++++++++++ > 3 files changed, 554 insertions(+) > > diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile > index ccf1ba57fa87..e626c4b82b29 100644 > --- a/arch/arm64/boot/dts/amlogic/Makefile > +++ b/arch/arm64/boot/dts/amlogic/Makefile > @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb > +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-bananapi-cm4-cm4io.dtb ^ Please add before meson-g12b-gsking-x.dtb to keep the list sorted > dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb > dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4-cm4io.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4-cm4io.dts > new file mode 100644 > index 000000000000..2c4a5b3f1b20 > --- /dev/null > +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4-cm4io.dts > @@ -0,0 +1,165 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org> > + */ > + > +/dts-v1/; > + > +#include "meson-g12b-bananapi-cm4.dtsi" > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/sound/meson-g12a-tohdmitx.h> > + > +/ { > + compatible = "bananapi,bpi-cm4io", "bananapi,bpi-cm4", "amlogic,a311d", "amlogic,g12b"; > + model = "BananaPi BPI-CM4IO Baseboard with BPI-CM4 Module"; > + > + aliases { > + ethernet0 = ðmac; > + i2c0 = &i2c1; > + i2c1 = &i2c3; > + }; > + > + adc-keys { > + compatible = "adc-keys"; > + io-channels = <&saradc 2>; > + io-channel-names = "buttons"; > + keyup-threshold-microvolt = <1710000>; > + > + button-function { > + label = "Function"; > + linux,code = <KEY_FN>; > + press-threshold-microvolt = <10000>; > + }; > + }; > + > + hdmi_connector: hdmi-connector { > + compatible = "hdmi-connector"; > + type = "a"; > + > + port { > + hdmi_connector_in: endpoint { > + remote-endpoint = <&hdmi_tx_tmds_out>; > + }; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + led-blue { > + color = <LED_COLOR_ID_BLUE>; > + function = LED_FUNCTION_STATUS; > + gpios = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + }; > + > + led-green { > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_STATUS; > + gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>; > + }; > + }; > + > + sound { > + compatible = "amlogic,axg-sound-card"; > + model = "BPI-CM4IO"; > + audio-aux-devs = <&tdmout_b>; > + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 0", > + "TDMOUT_B IN 1", "FRDDR_B OUT 0", > + "TDMOUT_B IN 2", "FRDDR_C OUT 0", ^ Should be “FRDDR_A OUT 1” and same for FRDDR_B/C else dmesg is spammed with: Mar 04 08:12:24 LibreELEC kernel: fe.dai-link-0: ASoC: no backend DAIs enabled for fe.dai-link-0 Mar 04 08:12:24 LibreELEC kernel: fe.dai-link-0: ASoC: error at dpcm_fe_dai_prepare on fe.dai-link-0: -22 Mar 04 08:12:24 LibreELEC kernel: fe.dai-link-0: ASoC: no backend DAIs enabled for fe.dai-link-0 Mar 04 08:12:24 LibreELEC kernel: fe.dai-link-0: ASoC: error at dpcm_fe_dai_prepare on fe.dai-link-0: -22 > + "TDM_B Playback", "TDMOUT_B OUT"; > + > + assigned-clocks = <&clkc CLKID_MPLL2>, > + <&clkc CLKID_MPLL0>, > + <&clkc CLKID_MPLL1>; > + assigned-clock-parents = <0>, <0>, <0>; > + assigned-clock-rates = <294912000>, > + <270950400>, > + <393216000>; > + > + dai-link-0 { > + sound-dai = <&frddr_a>; > + }; > + > + dai-link-1 { > + sound-dai = <&frddr_b>; > + }; > + > + dai-link-2 { > + sound-dai = <&frddr_c>; > + }; > + > + /* 8ch hdmi interface */ > + dai-link-3 { > + sound-dai = <&tdmif_b>; > + dai-format = "i2s"; > + dai-tdm-slot-tx-mask-0 = <1 1>; > + dai-tdm-slot-tx-mask-1 = <1 1>; > + dai-tdm-slot-tx-mask-2 = <1 1>; > + dai-tdm-slot-tx-mask-3 = <1 1>; > + mclk-fs = <256>; > + > + codec { > + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; > + }; > + }; > + > + /* hdmi glue */ > + dai-link-4 { > + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; > + > + codec { > + sound-dai = <&hdmi_tx>; > + }; > + }; > + }; > +}; > + > +&cecb_AO { > + status = "okay"; > +}; > + > +ðmac { > + status = "okay"; > +}; > + > +&hdmi_tx { > + status = "okay"; > +}; > + > +&hdmi_tx_tmds_port { > + hdmi_tx_tmds_out: endpoint { > + remote-endpoint = <&hdmi_connector_in>; > + }; > +}; > + > +/* CSI port */ > +&i2c1 { > + status = "okay"; > +}; > + > +/* DSI port for touchscreen */ > +&i2c3 { > + status = "okay"; > +}; > + > +/* miniPCIe port with USB + SIM slot */ > +&pcie { > + status = "okay"; > +}; > + > +&sd_emmc_b { > + status = "okay"; > +}; > + > +&tohdmitx { > + status = "okay"; > +}; > + > +/* Peripheral Only USB-C port */ > +&usb { > + dr_mode = "peripheral"; > + > + status = "okay"; > +}; > diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4.dtsi > new file mode 100644 > index 000000000000..dc0988c82694 > --- /dev/null > +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4.dtsi > @@ -0,0 +1,388 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org> > + */ > + > +#include "meson-g12b-a311d.dtsi" > +#include <dt-bindings/gpio/meson-g12a-gpio.h> > + > +/ { > + aliases { > + serial0 = &uart_AO; > + rtc1 = &vrtc; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + emmc_pwrseq: emmc-pwrseq { > + compatible = "mmc-pwrseq-emmc"; > + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; > + }; > + > + memory@0 { > + device_type = "memory"; > + reg = <0x0 0x0 0x0 0x40000000>; > + }; > + > + sdio_pwrseq: sdio-pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&gpio GPIOAO_6 GPIO_ACTIVE_LOW>; > + clocks = <&wifi32k>; > + clock-names = "ext_clock"; > + }; > + > + emmc_1v8: regulator-emmc_1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "EMMC_1V8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vddao_3v3>; > + regulator-always-on; > + }; > + > + dc_in: regulator-dc-in { > + compatible = "regulator-fixed"; > + regulator-name = "DC_IN"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > + vddio_c: regulator-vddio-c { > + compatible = "regulator-gpio"; > + regulator-name = "VDDIO_C"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + > + enable-gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>; > + enable-active-high; > + regulator-always-on; > + > + gpios = <&gpio_ao GPIOAO_9 GPIO_OPEN_DRAIN>; > + gpios-states = <1>; > + > + states = <1800000 0>, > + <3300000 1>; > + }; > + > + vddao_1v8: regulator-vddao-1v8 { > + compatible = "regulator-fixed"; > + regulator-name = "VDDAO_1V8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vddao_3v3>; > + regulator-always-on; > + }; > + > + vddao_3v3: regulator-vddao-3v3 { > + compatible = "regulator-fixed"; > + regulator-name = "VDDAO_3V3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + vin-supply = <&dc_in>; > + regulator-always-on; > + }; > + > + vddcpu_a: regulator-vddcpu-a { > + /* > + * MP8756GD DC/DC Regulator. > + */ > + compatible = "pwm-regulator"; > + > + regulator-name = "VDDCPU_A"; > + regulator-min-microvolt = <680000>; > + regulator-max-microvolt = <1040000>; > + > + pwm-supply = <&dc_in>; > + > + pwms = <&pwm_ab 0 1250 0>; > + pwm-dutycycle-range = <100 0>; > + > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vddcpu_b: regulator-vddcpu-b { > + /* > + * SY8120B1ABC DC/DC Regulator. > + */ > + compatible = "pwm-regulator"; > + > + regulator-name = "VDDCPU_B"; > + regulator-min-microvolt = <680000>; > + regulator-max-microvolt = <1040000>; > + > + pwm-supply = <&dc_in>; > + > + pwms = <&pwm_AO_cd 1 1250 0>; > + pwm-dutycycle-range = <100 0>; > + > + regulator-boot-on; > + regulator-always-on; > + }; > + > + wifi32k: wifi32k { > + compatible = "pwm-clock"; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ > + }; > +}; > + > +&arb { > + status = "okay"; > +}; > + > +&clkc_audio { > + status = "okay"; > +}; > + > +&cec_AO { > + pinctrl-0 = <&cec_ao_a_h_pins>; > + pinctrl-names = "default"; > + hdmi-phandle = <&hdmi_tx>; > +}; > + > +&cecb_AO { > + pinctrl-0 = <&cec_ao_b_h_pins>; > + pinctrl-names = "default"; > + hdmi-phandle = <&hdmi_tx>; > +}; > + > +&cpu0 { > + cpu-supply = <&vddcpu_b>; > + operating-points-v2 = <&cpu_opp_table_0>; > + clocks = <&clkc CLKID_CPU_CLK>; > + clock-latency = <50000>; > +}; > + > +&cpu1 { > + cpu-supply = <&vddcpu_b>; > + operating-points-v2 = <&cpu_opp_table_0>; > + clocks = <&clkc CLKID_CPU_CLK>; > + clock-latency = <50000>; > +}; > + > +&cpu100 { > + cpu-supply = <&vddcpu_a>; > + operating-points-v2 = <&cpub_opp_table_1>; > + clocks = <&clkc CLKID_CPUB_CLK>; > + clock-latency = <50000>; > +}; > + > +&cpu101 { > + cpu-supply = <&vddcpu_a>; > + operating-points-v2 = <&cpub_opp_table_1>; > + clocks = <&clkc CLKID_CPUB_CLK>; > + clock-latency = <50000>; > +}; > + > +&cpu102 { > + cpu-supply = <&vddcpu_a>; > + operating-points-v2 = <&cpub_opp_table_1>; > + clocks = <&clkc CLKID_CPUB_CLK>; > + clock-latency = <50000>; > +}; > + > +&cpu103 { > + cpu-supply = <&vddcpu_a>; > + operating-points-v2 = <&cpub_opp_table_1>; > + clocks = <&clkc CLKID_CPUB_CLK>; > + clock-latency = <50000>; > +}; > + > +&ext_mdio { > + external_phy: ethernet-phy@0 { > + /* Realtek RTL8211F (0x001cc916) */ > + reg = <0>; > + max-speed = <1000>; > + > + interrupt-parent = <&gpio_intc>; > + /* MAC_INTR on GPIOZ_14 */ > + interrupts = <26 IRQ_TYPE_LEVEL_LOW>; > + }; > +}; > + > +/* Ethernet to be enabled in baseboard DT */ > +ðmac { > + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; > + pinctrl-names = "default"; > + phy-mode = "rgmii-txid"; > + phy-handle = <&external_phy>; > +}; > + > +&frddr_a { > + status = "okay"; > +}; > + > +&frddr_b { > + status = "okay"; > +}; > + > +&frddr_c { > + status = "okay"; > +}; > + > +/* HDMI to be enabled in baseboard DT */ > +&hdmi_tx { > + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; > + pinctrl-names = "default"; > + hdmi-supply = <&dc_in>; > +}; > + > +/* "Camera" I2C bus */ > +&i2c1 { > + pinctrl-0 = <&i2c1_sda_h6_pins>, <&i2c1_sck_h7_pins>; > + pinctrl-names = "default"; > +}; > + > +/* Main I2C bus */ > +&i2c2 { > + pinctrl-0 = <&i2c2_sda_x_pins>, <&i2c2_sck_x_pins>; > + pinctrl-names = "default"; > +}; > + > +/* "ID" I2C bus */ > +&i2c3 { > + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; > + pinctrl-names = "default"; > +}; > + > +&pcie { > + reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>; > +}; > + > +&pwm_ab { > + pinctrl-0 = <&pwm_a_e_pins>; > + pinctrl-names = "default"; > + clocks = <&xtal>; > + clock-names = "clkin0"; > + > + status = "okay"; > +}; > + > +&pwm_ef { > + pinctrl-0 = <&pwm_e_pins>; > + pinctrl-names = "default"; > + > + status = "okay"; > +}; > + > +&pwm_AO_cd { > + pinctrl-0 = <&pwm_ao_d_e_pins>; > + pinctrl-names = "default"; > + clocks = <&xtal>; > + clock-names = "clkin1"; > + > + status = "okay"; > +}; > + > +&saradc { > + vref-supply = <&vddao_1v8>; > + > + status = "okay"; > +}; > + > +/* on-module SDIO WiFi */ > +&sd_emmc_a { > + pinctrl-0 = <&sdio_pins>; > + pinctrl-1 = <&sdio_clk_gate_pins>; > + pinctrl-names = "default", "clk-gate"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + bus-width = <4>; > + sd-uhs-sdr104; > + max-frequency = <50000000>; > + > + non-removable; > + disable-wp; > + > + /* WiFi firmware requires power in suspend */ > + keep-power-in-suspend; > + > + mmc-pwrseq = <&sdio_pwrseq>; > + > + vmmc-supply = <&vddao_3v3>; > + vqmmc-supply = <&vddao_3v3>; > + > + status = "okay"; > + > + rtl8822cs: wifi@1 { > + reg = <1>; > + }; > +}; > + > +/* SD card to be enabled in baseboard DT */ > +&sd_emmc_b { > + pinctrl-0 = <&sdcard_c_pins>; > + pinctrl-1 = <&sdcard_clk_gate_c_pins>; > + pinctrl-names = "default", "clk-gate"; > + > + bus-width = <4>; > + cap-sd-highspeed; > + max-frequency = <50000000>; > + disable-wp; > + > + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; > + vmmc-supply = <&vddao_3v3>; > + vqmmc-supply = <&vddio_c>; > +}; > + > +/* on-module eMMC */ > +&sd_emmc_c { > + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; > + pinctrl-1 = <&emmc_clk_gate_pins>; > + pinctrl-names = "default", "clk-gate"; > + > + bus-width = <8>; > + cap-mmc-highspeed; > + mmc-ddr-1_8v; > + mmc-hs200-1_8v; > + max-frequency = <200000000>; > + disable-wp; > + > + mmc-pwrseq = <&emmc_pwrseq>; > + vmmc-supply = <&vddao_3v3>; > + vqmmc-supply = <&vddao_1v8>; > + > + status = "okay"; > +}; > + > +&tdmif_b { > + status = "okay"; > +}; > + > +&tdmout_b { > + status = "okay"; > +}; > + > +/* on-module UART BT */ > +&uart_A { > + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; > + pinctrl-names = "default"; > + uart-has-rtscts; > + > + status = "okay"; > + > + bluetooth { > + compatible = "realtek,rtl8822cs-bt"; > + enable-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>; > + host-wake-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>; > + device-wake-gpios = <&gpio GPIOX_18 GPIO_ACTIVE_HIGH>; > + }; > +}; > + > +&uart_AO { > + pinctrl-0 = <&uart_ao_a_pins>; > + pinctrl-names = "default"; > + > + status = "okay"; > +}; > + > +&usb { > + phys = <&usb2_phy0>, <&usb2_phy1>; > + phy-names = "usb2-phy0", "usb2-phy1"; > +}; With the audio correction all appears to be good, here’s dmesg: http://ix.io/4pTy Tested-by: Christian Hewitt <christianshewitt@gmail.com> Christian
On 03/03/2023 18:37, Neil Armstrong wrote: > Add support for both the BananaPi BPI-CM4 module and the BananaPi > baseboard which is comnpatible with the RaspberryPi CM4IO baseboard. > > The BananaPi BPI-CM4 module follows the CM4 specifications at [1], > but with a single HDMI port and a since DSI output. > (...) > + sdio_pwrseq: sdio-pwrseq { > + compatible = "mmc-pwrseq-simple"; > + reset-gpios = <&gpio GPIOAO_6 GPIO_ACTIVE_LOW>; > + clocks = <&wifi32k>; > + clock-names = "ext_clock"; > + }; > + > + emmc_1v8: regulator-emmc_1v8 { No underscores in node names. > + compatible = "regulator-fixed"; > + regulator-name = "EMMC_1V8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + vin-supply = <&vddao_3v3>; > + regulator-always-on; > + }; > + > + dc_in: regulator-dc-in { > + compatible = "regulator-fixed"; > + regulator-name = "DC_IN"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; > + > Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index ccf1ba57fa87..e626c4b82b29 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2l.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-radxa-zero2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-bananapi-cm4-cm4io.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4-cm4io.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4-cm4io.dts new file mode 100644 index 000000000000..2c4a5b3f1b20 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4-cm4io.dts @@ -0,0 +1,165 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org> + */ + +/dts-v1/; + +#include "meson-g12b-bananapi-cm4.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/sound/meson-g12a-tohdmitx.h> + +/ { + compatible = "bananapi,bpi-cm4io", "bananapi,bpi-cm4", "amlogic,a311d", "amlogic,g12b"; + model = "BananaPi BPI-CM4IO Baseboard with BPI-CM4 Module"; + + aliases { + ethernet0 = ðmac; + i2c0 = &i2c1; + i2c1 = &i2c3; + }; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 2>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1710000>; + + button-function { + label = "Function"; + linux,code = <KEY_FN>; + press-threshold-microvolt = <10000>; + }; + }; + + hdmi_connector: hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-blue { + color = <LED_COLOR_ID_BLUE>; + function = LED_FUNCTION_STATUS; + gpios = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led-green { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_STATUS; + gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>; + }; + }; + + sound { + compatible = "amlogic,axg-sound-card"; + model = "BPI-CM4IO"; + audio-aux-devs = <&tdmout_b>; + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 0", + "TDMOUT_B IN 1", "FRDDR_B OUT 0", + "TDMOUT_B IN 2", "FRDDR_C OUT 0", + "TDM_B Playback", "TDMOUT_B OUT"; + + assigned-clocks = <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>; + assigned-clock-parents = <0>, <0>, <0>; + assigned-clock-rates = <294912000>, + <270950400>, + <393216000>; + + dai-link-0 { + sound-dai = <&frddr_a>; + }; + + dai-link-1 { + sound-dai = <&frddr_b>; + }; + + dai-link-2 { + sound-dai = <&frddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-3 { + sound-dai = <&tdmif_b>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + dai-tdm-slot-tx-mask-1 = <1 1>; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + mclk-fs = <256>; + + codec { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; + }; + }; + + /* hdmi glue */ + dai-link-4 { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + }; +}; + +&cecb_AO { + status = "okay"; +}; + +ðmac { + status = "okay"; +}; + +&hdmi_tx { + status = "okay"; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +/* CSI port */ +&i2c1 { + status = "okay"; +}; + +/* DSI port for touchscreen */ +&i2c3 { + status = "okay"; +}; + +/* miniPCIe port with USB + SIM slot */ +&pcie { + status = "okay"; +}; + +&sd_emmc_b { + status = "okay"; +}; + +&tohdmitx { + status = "okay"; +}; + +/* Peripheral Only USB-C port */ +&usb { + dr_mode = "peripheral"; + + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4.dtsi new file mode 100644 index 000000000000..dc0988c82694 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-bananapi-cm4.dtsi @@ -0,0 +1,388 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2023 Neil Armstrong <neil.armstrong@linaro.org> + */ + +#include "meson-g12b-a311d.dtsi" +#include <dt-bindings/gpio/meson-g12a-gpio.h> + +/ { + aliases { + serial0 = &uart_AO; + rtc1 = &vrtc; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOAO_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + emmc_1v8: regulator-emmc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "EMMC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + dc_in: regulator-dc-in { + compatible = "regulator-fixed"; + regulator-name = "DC_IN"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vddio_c: regulator-vddio-c { + compatible = "regulator-gpio"; + regulator-name = "VDDIO_C"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + enable-gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>; + enable-active-high; + regulator-always-on; + + gpios = <&gpio_ao GPIOAO_9 GPIO_OPEN_DRAIN>; + gpios-states = <1>; + + states = <1800000 0>, + <3300000 1>; + }; + + vddao_1v8: regulator-vddao-1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao-3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&dc_in>; + regulator-always-on; + }; + + vddcpu_a: regulator-vddcpu-a { + /* + * MP8756GD DC/DC Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU_A"; + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwm-supply = <&dc_in>; + + pwms = <&pwm_ab 0 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + vddcpu_b: regulator-vddcpu-b { + /* + * SY8120B1ABC DC/DC Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU_B"; + regulator-min-microvolt = <680000>; + regulator-max-microvolt = <1040000>; + + pwm-supply = <&dc_in>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; +}; + +&arb { + status = "okay"; +}; + +&clkc_audio { + status = "okay"; +}; + +&cec_AO { + pinctrl-0 = <&cec_ao_a_h_pins>; + pinctrl-names = "default"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cecb_AO { + pinctrl-0 = <&cec_ao_b_h_pins>; + pinctrl-names = "default"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cpu0 { + cpu-supply = <&vddcpu_b>; + operating-points-v2 = <&cpu_opp_table_0>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu_b>; + operating-points-v2 = <&cpu_opp_table_0>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu100 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu101 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu102 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&cpu103 { + cpu-supply = <&vddcpu_a>; + operating-points-v2 = <&cpub_opp_table_1>; + clocks = <&clkc CLKID_CPUB_CLK>; + clock-latency = <50000>; +}; + +&ext_mdio { + external_phy: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + max-speed = <1000>; + + interrupt-parent = <&gpio_intc>; + /* MAC_INTR on GPIOZ_14 */ + interrupts = <26 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +/* Ethernet to be enabled in baseboard DT */ +ðmac { + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + phy-mode = "rgmii-txid"; + phy-handle = <&external_phy>; +}; + +&frddr_a { + status = "okay"; +}; + +&frddr_b { + status = "okay"; +}; + +&frddr_c { + status = "okay"; +}; + +/* HDMI to be enabled in baseboard DT */ +&hdmi_tx { + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; + pinctrl-names = "default"; + hdmi-supply = <&dc_in>; +}; + +/* "Camera" I2C bus */ +&i2c1 { + pinctrl-0 = <&i2c1_sda_h6_pins>, <&i2c1_sck_h7_pins>; + pinctrl-names = "default"; +}; + +/* Main I2C bus */ +&i2c2 { + pinctrl-0 = <&i2c2_sda_x_pins>, <&i2c2_sck_x_pins>; + pinctrl-names = "default"; +}; + +/* "ID" I2C bus */ +&i2c3 { + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; + pinctrl-names = "default"; +}; + +&pcie { + reset-gpios = <&gpio GPIOA_8 GPIO_ACTIVE_LOW>; +}; + +&pwm_ab { + pinctrl-0 = <&pwm_a_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin0"; + + status = "okay"; +}; + +&pwm_ef { + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + + status = "okay"; +}; + +&saradc { + vref-supply = <&vddao_1v8>; + + status = "okay"; +}; + +/* on-module SDIO WiFi */ +&sd_emmc_a { + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + sd-uhs-sdr104; + max-frequency = <50000000>; + + non-removable; + disable-wp; + + /* WiFi firmware requires power in suspend */ + keep-power-in-suspend; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddao_3v3>; + + status = "okay"; + + rtl8822cs: wifi@1 { + reg = <1>; + }; +}; + +/* SD card to be enabled in baseboard DT */ +&sd_emmc_b { + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_c>; +}; + +/* on-module eMMC */ +&sd_emmc_c { + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddao_1v8>; + + status = "okay"; +}; + +&tdmif_b { + status = "okay"; +}; + +&tdmout_b { + status = "okay"; +}; + +/* on-module UART BT */ +&uart_A { + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; + + status = "okay"; + + bluetooth { + compatible = "realtek,rtl8822cs-bt"; + enable-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>; + host-wake-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>; + device-wake-gpios = <&gpio GPIOX_18 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart_AO { + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&usb { + phys = <&usb2_phy0>, <&usb2_phy1>; + phy-names = "usb2-phy0", "usb2-phy1"; +};
Add support for both the BananaPi BPI-CM4 module and the BananaPi baseboard which is comnpatible with the RaspberryPi CM4IO baseboard. The BananaPi BPI-CM4 module follows the CM4 specifications at [1], but with a single HDMI port and a since DSI output. The current CM4IO baseboard DT should work fine on the Raspberry CM4 baseboard and other derivatives baseboards, but proper DT should be written for other baseboards. The split is done so it's easy to describe a new CM4 baseboard, enabling only the necessary HW used on the baseboard. [1] https://datasheets.raspberrypi.com/cm4io/cm4io-datasheet.pdf Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../dts/amlogic/meson-g12b-bananapi-cm4-cm4io.dts | 165 +++++++++ .../boot/dts/amlogic/meson-g12b-bananapi-cm4.dtsi | 388 +++++++++++++++++++++ 3 files changed, 554 insertions(+)