diff mbox series

[11/13] ARM: dts: add support for WeTek Hub and WeTek Play2

Message ID 20230323065458.776029-12-christianshewitt@gmail.com (mailing list archive)
State Superseded
Headers show
Series boards: amlogic: add BananaPi/Radxa/WeTek boards | expand

Commit Message

Christian Hewitt March 23, 2023, 6:54 a.m. UTC 
Import the dts files from linux-amlogic/for-next (Linux 6.4-rc1) and
add the old PHY reset bindings for dwmac to the u-boot.dtsi until we
support the new bindings in the PHY node. Without this the PHY is not
functional in u-boot or Linux.

Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
---
 arch/arm/dts/Makefile                     |   2 +
 arch/arm/dts/meson-gxbb-wetek-hub.dts     |  58 +++++
 arch/arm/dts/meson-gxbb-wetek-play2.dts   | 119 +++++++++
 arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi |  13 +
 arch/arm/dts/meson-gxbb-wetek.dtsi        | 292 ++++++++++++++++++++++
 5 files changed, 484 insertions(+)
 create mode 100644 arch/arm/dts/meson-gxbb-wetek-hub.dts
 create mode 100644 arch/arm/dts/meson-gxbb-wetek-play2.dts
 create mode 100644 arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi
 create mode 100644 arch/arm/dts/meson-gxbb-wetek.dtsi

Comments

Neil Armstrong March 23, 2023, 8:51 a.m. UTC | #1 
On 23/03/2023 07:54, Christian Hewitt wrote:
> Import the dts files from linux-amlogic/for-next (Linux 6.4-rc1) and
> add the old PHY reset bindings for dwmac to the u-boot.dtsi until we
> support the new bindings in the PHY node. Without this the PHY is not
> functional in u-boot or Linux.
> 
> Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
> ---
>   arch/arm/dts/Makefile                     |   2 +
>   arch/arm/dts/meson-gxbb-wetek-hub.dts     |  58 +++++
>   arch/arm/dts/meson-gxbb-wetek-play2.dts   | 119 +++++++++
>   arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi |  13 +
>   arch/arm/dts/meson-gxbb-wetek.dtsi        | 292 ++++++++++++++++++++++
>   5 files changed, 484 insertions(+)
>   create mode 100644 arch/arm/dts/meson-gxbb-wetek-hub.dts
>   create mode 100644 arch/arm/dts/meson-gxbb-wetek-play2.dts
>   create mode 100644 arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi
>   create mode 100644 arch/arm/dts/meson-gxbb-wetek.dtsi
> 
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 42da335bb5..1c843882d1 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -191,6 +191,8 @@ dtb-$(CONFIG_ARCH_MESON) += \
>   	meson-gxbb-nanopi-k2.dtb \
>   	meson-gxbb-p200.dtb \
>   	meson-gxbb-p201.dtb \
> +	meson-gxbb-wetek-hub.dtb \
> +	meson-gxbb-wetek-play2.dtb \
>   	meson-gxl-s805x-libretech-ac.dtb \
>   	meson-gxl-s905d-libretech-pc.dtb \
>   	meson-gxl-s905w-jethome-jethub-j80.dtb \
> diff --git a/arch/arm/dts/meson-gxbb-wetek-hub.dts b/arch/arm/dts/meson-gxbb-wetek-hub.dts
> new file mode 100644
> index 0000000000..58733017ed
> --- /dev/null
> +++ b/arch/arm/dts/meson-gxbb-wetek-hub.dts
> @@ -0,0 +1,58 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2016 BayLibre, Inc.
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-gxbb-wetek.dtsi"
> +#include <dt-bindings/sound/meson-aiu.h>
> +
> +/ {
> +	compatible = "wetek,hub", "amlogic,meson-gxbb";
> +	model = "WeTek Hub";
> +
> +	sound {
> +		compatible = "amlogic,gx-sound-card";
> +		model = "WETEK-HUB";
> +		assigned-clocks = <&clkc CLKID_MPLL0>,
> +				  <&clkc CLKID_MPLL1>,
> +				  <&clkc CLKID_MPLL2>;
> +		assigned-clock-parents = <0>, <0>, <0>;
> +		assigned-clock-rates = <294912000>,
> +				       <270950400>,
> +				       <393216000>;
> +		status = "okay";
> +
> +		dai-link-0 {
> +			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
> +		};
> +
> +		dai-link-1 {
> +			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
> +			dai-format = "i2s";
> +			mclk-fs = <256>;
> +
> +			codec-0 {
> +				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
> +			};
> +		};
> +
> +		dai-link-2 {
> +			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
> +
> +			codec-0 {
> +				sound-dai = <&hdmi_tx>;
> +			};
> +		};
> +	};
> +};
> +
> +&aiu {
> +	status = "okay";
> +};
> +
> +&ir {
> +	linux,rc-map-name = "rc-wetek-hub";
> +};
> diff --git a/arch/arm/dts/meson-gxbb-wetek-play2.dts b/arch/arm/dts/meson-gxbb-wetek-play2.dts
> new file mode 100644
> index 0000000000..505ffcd8eb
> --- /dev/null
> +++ b/arch/arm/dts/meson-gxbb-wetek-play2.dts
> @@ -0,0 +1,119 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2016 BayLibre, Inc.
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-gxbb-wetek.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/sound/meson-aiu.h>
> +
> +/ {
> +	compatible = "wetek,play2", "amlogic,meson-gxbb";
> +	model = "WeTek Play 2";
> +
> +	spdif_dit: audio-codec-0 {
> +		#sound-dai-cells = <0>;
> +		compatible = "linux,spdif-dit";
> +		status = "okay";
> +		sound-name-prefix = "DIT";
> +	};
> +
> +	leds {
> +		led-wifi {
> +			label = "wetek-play:wifi-status";
> +			gpios = <&gpio GPIODV_26 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +
> +		led-ethernet {
> +			label = "wetek-play:ethernet-status";
> +			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
> +			default-state = "off";
> +		};
> +	};
> +
> +	gpio-keys-polled {
> +		compatible = "gpio-keys-polled";
> +		poll-interval = <100>;
> +
> +		button {
> +			label = "reset";
> +			linux,code = <KEY_RESTART>;
> +			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +
> +	sound {
> +		compatible = "amlogic,gx-sound-card";
> +		model = "WETEK-PLAY2";
> +		assigned-clocks = <&clkc CLKID_MPLL0>,
> +				  <&clkc CLKID_MPLL1>,
> +				  <&clkc CLKID_MPLL2>;
> +		assigned-clock-parents = <0>, <0>, <0>;
> +		assigned-clock-rates = <294912000>,
> +				       <270950400>,
> +				       <393216000>;
> +		status = "okay";
> +
> +		dai-link-0 {
> +			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
> +		};
> +
> +		dai-link-1 {
> +			sound-dai = <&aiu AIU_CPU CPU_SPDIF_FIFO>;
> +		};
> +
> +		dai-link-2 {
> +			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
> +			dai-format = "i2s";
> +			mclk-fs = <256>;
> +
> +			codec-0 {
> +				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
> +			};
> +		};
> +
> +		dai-link-3 {
> +			sound-dai = <&aiu AIU_CPU CPU_SPDIF_ENCODER>;
> +
> +			codec-0 {
> +				sound-dai = <&spdif_dit>;
> +			};
> +		};
> +
> +		dai-link-4 {
> +			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
> +
> +			codec-0 {
> +				sound-dai = <&hdmi_tx>;
> +			};
> +		};
> +	};
> +};
> +
> +&aiu {
> +	status = "okay";
> +	pinctrl-0 = <&spdif_out_y_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&i2c_A {
> +	status = "okay";
> +	pinctrl-0 = <&i2c_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb1_phy {
> +	status = "okay";
> +};
> +
> +&usb1 {
> +	status = "okay";
> +};
> +
> +&ir {
> +	linux,rc-map-name = "rc-wetek-play2";
> +};
> diff --git a/arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi b/arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi
> new file mode 100644
> index 0000000000..3743053eb9
> --- /dev/null
> +++ b/arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi
> @@ -0,0 +1,13 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2019 BayLibre, SAS.
> + * Author: Neil Armstrong <narmstrong@baylibre.com>
> + */
> +
> +#include "meson-gx-u-boot.dtsi"
> +
> +&ethmac {
> +	snps,reset-gpio = <&gpio GPIOZ_14 0>;
> +	snps,reset-delays-us = <0 10000 1000000>;
> +	snps,reset-active-low;
> +};
> diff --git a/arch/arm/dts/meson-gxbb-wetek.dtsi b/arch/arm/dts/meson-gxbb-wetek.dtsi
> new file mode 100644
> index 0000000000..94dafb9553
> --- /dev/null
> +++ b/arch/arm/dts/meson-gxbb-wetek.dtsi
> @@ -0,0 +1,292 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2016 Andreas Färber
> + * Copyright (c) 2016 BayLibre, Inc.
> + * Author: Kevin Hilman <khilman@kernel.org>
> + */
> +
> +#include "meson-gxbb.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> +	aliases {
> +		serial0 = &uart_AO;
> +		ethernet0 = &ethmac;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x40000000>;
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		led-power {
> +			/* red in suspend or power-off */
> +			color = <LED_COLOR_ID_BLUE>;
> +			function = LED_FUNCTION_POWER;
> +			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +			panic-indicator;
> +		};
> +	};
> +
> +	usb_pwr: regulator-usb-pwrs {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "USB_PWR";
> +
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +
> +		gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	vddio_boot: regulator-vddio_boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	vddio_ao18: regulator-vddio_ao18 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO18";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-always-on;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	cvbs-connector {
> +		compatible = "composite-video-connector";
> +
> +		port {
> +			cvbs_connector_in: endpoint {
> +				remote-endpoint = <&cvbs_vdac_out>;
> +			};
> +		};
> +	};
> +
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_connector_in: endpoint {
> +				remote-endpoint = <&hdmi_tx_tmds_out>;
> +			};
> +		};
> +	};
> +};
> +
> +&cec_AO {
> +	status = "okay";
> +	pinctrl-0 = <&ao_cec_pins>;
> +	pinctrl-names = "default";
> +	hdmi-phandle = <&hdmi_tx>;
> +};
> +
> +&cvbs_vdac_port {
> +	cvbs_vdac_out: endpoint {
> +		remote-endpoint = <&cvbs_connector_in>;
> +	};
> +};
> +
> +&ethmac {
> +	status = "okay";
> +	pinctrl-0 = <&eth_rgmii_pins>;
> +	pinctrl-names = "default";
> +
> +	phy-handle = <&eth_phy0>;
> +	phy-mode = "rgmii";
> +
> +	amlogic,tx-delay-ns = <2>;
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		eth_phy0: ethernet-phy@0 {
> +			/* Realtek RTL8211F (0x001cc916) */
> +			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <80000>;
> +			reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
> +
> +			interrupt-parent = <&gpio_intc>;
> +			/* MAC_INTR on GPIOZ_15 */
> +			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
> +		};
> +	};
> +};
> +
> +&hdmi_tx {
> +	status = "okay";
> +	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
> +	pinctrl-names = "default";
> +	hdmi-supply = <&vddio_ao18>;
> +};
> +
> +&hdmi_tx_tmds_port {
> +	hdmi_tx_tmds_out: endpoint {
> +		remote-endpoint = <&hdmi_connector_in>;
> +	};
> +};
> +
> +&ir {
> +	status = "okay";
> +	pinctrl-0 = <&remote_input_ao_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&pwm_ef {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_e_pins>;
> +	pinctrl-names = "default";
> +	clocks = <&clkc CLKID_FCLK_DIV4>;
> +	clock-names = "clkin0";
> +};
> +
> +&saradc {
> +	status = "okay";
> +	vref-supply = <&vddio_ao18>;
> +};
> +
> +/* Wireless SDIO Module */
> +&sd_emmc_a {
> +	status = "okay";
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <50000000>;
> +
> +	non-removable;
> +	disable-wp;
> +
> +	/* WiFi firmware requires power to be kept while in suspend */
> +	keep-power-in-suspend;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +
> +	brcmf: wifi@1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> +	status = "okay";
> +	pinctrl-0 = <&sdcard_pins>;
> +	pinctrl-1 = <&sdcard_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <50000000>;
> +	disable-wp;
> +
> +	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vcc_3v3>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> +	pinctrl-1 = <&emmc_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* This is connected to the Bluetooth module: */
> +&uart_A {
> +	status = "okay";
> +	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +
> +	bluetooth {
> +		compatible = "brcm,bcm43438-bt";
> +		shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +/* This UART is brought out to the DB9 connector */
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb0_phy {
> +	status = "okay";
> +	phy-supply = <&usb_pwr>;
> +};
> +
> +&usb0 {
> +	status = "okay";
> +};

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
diff mbox series

Patch

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 42da335bb5..1c843882d1 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -191,6 +191,8 @@  dtb-$(CONFIG_ARCH_MESON) += \
 	meson-gxbb-nanopi-k2.dtb \
 	meson-gxbb-p200.dtb \
 	meson-gxbb-p201.dtb \
+	meson-gxbb-wetek-hub.dtb \
+	meson-gxbb-wetek-play2.dtb \
 	meson-gxl-s805x-libretech-ac.dtb \
 	meson-gxl-s905d-libretech-pc.dtb \
 	meson-gxl-s905w-jethome-jethub-j80.dtb \
diff --git a/arch/arm/dts/meson-gxbb-wetek-hub.dts b/arch/arm/dts/meson-gxbb-wetek-hub.dts
new file mode 100644
index 0000000000..58733017ed
--- /dev/null
+++ b/arch/arm/dts/meson-gxbb-wetek-hub.dts
@@ -0,0 +1,58 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 BayLibre, Inc.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb-wetek.dtsi"
+#include <dt-bindings/sound/meson-aiu.h>
+
+/ {
+	compatible = "wetek,hub", "amlogic,meson-gxbb";
+	model = "WeTek Hub";
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "WETEK-HUB";
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&aiu {
+	status = "okay";
+};
+
+&ir {
+	linux,rc-map-name = "rc-wetek-hub";
+};
diff --git a/arch/arm/dts/meson-gxbb-wetek-play2.dts b/arch/arm/dts/meson-gxbb-wetek-play2.dts
new file mode 100644
index 0000000000..505ffcd8eb
--- /dev/null
+++ b/arch/arm/dts/meson-gxbb-wetek-play2.dts
@@ -0,0 +1,119 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 BayLibre, Inc.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxbb-wetek.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/sound/meson-aiu.h>
+
+/ {
+	compatible = "wetek,play2", "amlogic,meson-gxbb";
+	model = "WeTek Play 2";
+
+	spdif_dit: audio-codec-0 {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+		status = "okay";
+		sound-name-prefix = "DIT";
+	};
+
+	leds {
+		led-wifi {
+			label = "wetek-play:wifi-status";
+			gpios = <&gpio GPIODV_26 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-ethernet {
+			label = "wetek-play:ethernet-status";
+			gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		button {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "WETEK-PLAY2";
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_SPDIF_FIFO>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+		};
+
+		dai-link-3 {
+			sound-dai = <&aiu AIU_CPU CPU_SPDIF_ENCODER>;
+
+			codec-0 {
+				sound-dai = <&spdif_dit>;
+			};
+		};
+
+		dai-link-4 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&aiu {
+	status = "okay";
+	pinctrl-0 = <&spdif_out_y_pins>;
+	pinctrl-names = "default";
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
+
+&ir {
+	linux,rc-map-name = "rc-wetek-play2";
+};
diff --git a/arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi b/arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi
new file mode 100644
index 0000000000..3743053eb9
--- /dev/null
+++ b/arch/arm/dts/meson-gxbb-wetek-u-boot.dtsi
@@ -0,0 +1,13 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-gx-u-boot.dtsi"
+
+&ethmac {
+	snps,reset-gpio = <&gpio GPIOZ_14 0>;
+	snps,reset-delays-us = <0 10000 1000000>;
+	snps,reset-active-low;
+};
diff --git a/arch/arm/dts/meson-gxbb-wetek.dtsi b/arch/arm/dts/meson-gxbb-wetek.dtsi
new file mode 100644
index 0000000000..94dafb9553
--- /dev/null
+++ b/arch/arm/dts/meson-gxbb-wetek.dtsi
@@ -0,0 +1,292 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016 Andreas Färber
+ * Copyright (c) 2016 BayLibre, Inc.
+ * Author: Kevin Hilman <khilman@kernel.org>
+ */
+
+#include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power {
+			/* red in suspend or power-off */
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			panic-indicator;
+		};
+	};
+
+	usb_pwr: regulator-usb-pwrs {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB_PWR";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+};
+
+&cec_AO {
+	status = "okay";
+	pinctrl-0 = <&ao_cec_pins>;
+	pinctrl-names = "default";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rgmii";
+
+	amlogic,tx-delay-ns = <2>;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* Realtek RTL8211F (0x001cc916) */
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <80000>;
+			reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
+			interrupt-parent = <&gpio_intc>;
+			/* MAC_INTR on GPIOZ_15 */
+			interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vddio_ao18>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vcc_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* This is connected to the Bluetooth module: */
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_20 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* This UART is brought out to the DB9 connector */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&usb0 {
+	status = "okay";
+};