| Message ID | 20230510102251.10118-6-marex@denx.de (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
| Series | [v3,1/6] dt-bindings: iio: temperature: melexis,mlx90614: Document MLX90615 support | expand |
Acked-by: Crt Mori <cmo@melexis.com> On Wed, 10 May 2023 at 12:23, Marek Vasut <marex@denx.de> wrote: > > Add support for MLX90615 Infra Red Thermometer, which seems to be > the predecesor of MLX90614 . There are significant differences in > the register layout compared to MLX90614, but the functionality > of the device is virtually identical. > > The following differences have been identified: > - RAM/EEPROM/SLEEP access opcodes are different > - RAM/EEPROM registers are at different offsets > - EEPROM emissivity and configuration registers are at different offsets > - EEPROM configuration register bits are shuffled around > - EEPROM emissivity settings are 14 bit on MLX90615 , 16 bit on MLX90614 > - MLX90615 can only ever support one sensor, MLX90614 could support two > - FIR filter is set to fixed settings on MLX90615 > - IIR filter coefficients are different > > This patch fills in the MLX90615 specific description and quirk handling. > > The IIR filter coefficients were provided by Melexis as follows: > 0b0000 - Forbidden value > 0b0001 - 100% - settling time = refresh rate = 205ms (around 5Hz) > 0b0010 - 50% - settling time = 2050ms (around 0.5Hz) > 0b0011 - 33% - settling time = 36900ms (around 0.3Hz) > 0b0100 - 25% - settling time = 5125ms (around 0.2Hz) > 0b0101 - 20% - settling time = 6355ms (around 0.15Hz) > 0b0110 - 17% - settling time = 7790ms (around 0.13Hz) > 0b0111 - 14% - settling time = 9225ms (around 0.1Hz) > > Signed-off-by: Marek Vasut <marex@denx.de> > --- > Cc: Crt Mori <cmo@melexis.com> > Cc: Jonathan Cameron <jic23@kernel.org> > Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> > Cc: Lars-Peter Clausen <lars@metafoo.de> > Cc: Marek Vasut <marex@denx.de> > Cc: Peter Meerwald <pmeerw@pmeerw.net> > Cc: Rob Herring <robh+dt@kernel.org> > Cc: devicetree@vger.kernel.org > Cc: linux-iio@vger.kernel.org > --- > V2: Split the patch up into cleanups, abstraction and MLX90615 addition > V3: Drop emissivity_res, update IIR filter coefficients per Melexis input > --- > drivers/iio/temperature/mlx90614.c | 48 +++++++++++++++++++++++++++--- > 1 file changed, 44 insertions(+), 4 deletions(-) > > diff --git a/drivers/iio/temperature/mlx90614.c b/drivers/iio/temperature/mlx90614.c > index 3aa108a652bb4..b2affcb795e00 100644 > --- a/drivers/iio/temperature/mlx90614.c > +++ b/drivers/iio/temperature/mlx90614.c > @@ -1,12 +1,15 @@ > // SPDX-License-Identifier: GPL-2.0-only > /* > - * mlx90614.c - Support for Melexis MLX90614 contactless IR temperature sensor > + * mlx90614.c - Support for Melexis MLX90614/MLX90615 contactless IR temperature sensor > * > * Copyright (c) 2014 Peter Meerwald <pmeerw@pmeerw.net> > * Copyright (c) 2015 Essensium NV > * Copyright (c) 2015 Melexis > * > - * Driver for the Melexis MLX90614 I2C 16-bit IR thermopile sensor > + * Driver for the Melexis MLX90614/MLX90615 I2C 16-bit IR thermopile sensor > + * > + * MLX90614 - 17-bit ADC + MLX90302 DSP > + * MLX90615 - 16-bit ADC + MLX90325 DSP > * > * (7-bit I2C slave address 0x5a, 100KHz bus speed only!) > * > @@ -35,6 +38,10 @@ > #define MLX90614_OP_EEPROM 0x20 > #define MLX90614_OP_SLEEP 0xff > > +#define MLX90615_OP_EEPROM 0x10 > +#define MLX90615_OP_RAM 0x20 > +#define MLX90615_OP_SLEEP 0xc6 > + > /* Control bits in configuration register */ > #define MLX90614_CONFIG_IIR_SHIFT 0 /* IIR coefficient */ > #define MLX90614_CONFIG_IIR_MASK (0x7 << MLX90614_CONFIG_IIR_SHIFT) > @@ -43,11 +50,16 @@ > #define MLX90614_CONFIG_FIR_SHIFT 8 /* FIR coefficient */ > #define MLX90614_CONFIG_FIR_MASK (0x7 << MLX90614_CONFIG_FIR_SHIFT) > > +#define MLX90615_CONFIG_IIR_SHIFT 12 /* IIR coefficient */ > +#define MLX90615_CONFIG_IIR_MASK (0x7 << MLX90615_CONFIG_IIR_SHIFT) > + > /* Timings (in ms) */ > #define MLX90614_TIMING_EEPROM 20 /* time for EEPROM write/erase to complete */ > #define MLX90614_TIMING_WAKEUP 34 /* time to hold SDA low for wake-up */ > #define MLX90614_TIMING_STARTUP 250 /* time before first data after wake-up */ > > +#define MLX90615_TIMING_WAKEUP 22 /* time to hold SCL low for wake-up */ > + > #define MLX90614_AUTOSLEEP_DELAY 5000 /* default autosleep delay */ > > /* Magic constants */ > @@ -305,8 +317,8 @@ static int mlx90614_read_raw(struct iio_dev *indio_dev, > *val2 = ret * NSEC_PER_SEC / chip_info->emissivity_max; > } > return IIO_VAL_INT_PLUS_NANO; > - case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: /* IIR setting with > - FIR = 1024 */ > + /* IIR setting with FIR=1024 (MLX90614) or FIR=65536 (MLX90615) */ > + case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: > ret = mlx90614_power_get(data, false); > if (ret < 0) > return ret; > @@ -664,14 +676,42 @@ static const struct mlx_chip_info mlx90614_chip_info = { > }, > }; > > +static const struct mlx_chip_info mlx90615_chip_info = { > + .op_eeprom_emissivity = MLX90615_OP_EEPROM | 0x03, > + .op_eeprom_config1 = MLX90615_OP_EEPROM | 0x02, > + .op_ram_ta = MLX90615_OP_RAM | 0x06, > + .op_ram_tobj1 = MLX90615_OP_RAM | 0x07, > + .op_ram_tobj2 = MLX90615_OP_RAM | 0x08, > + .op_sleep = MLX90615_OP_SLEEP, > + .dual_channel = false, > + .wakeup_delay_ms = MLX90615_TIMING_WAKEUP, > + .emissivity_max = 16383, > + .fir_config_mask = 0, /* MLX90615 FIR is fixed */ > + .iir_config_mask = MLX90615_CONFIG_IIR_MASK, > + /* IIR value 0 is FORBIDDEN COMBINATION on MLX90615 */ > + .iir_valid_offset = 1, > + .iir_values = { 500, 50, 30, 20, 15, 13, 10 }, > + .iir_freqs = { > + { 0, 100000 }, /* 14% ~= 0.10 Hz */ > + { 0, 130000 }, /* 17% ~= 0.13 Hz */ > + { 0, 150000 }, /* 20% ~= 0.15 Hz */ > + { 0, 200000 }, /* 25% ~= 0.20 Hz */ > + { 0, 300000 }, /* 33% ~= 0.30 Hz */ > + { 0, 500000 }, /* 50% ~= 0.50 Hz */ > + { 5, 000000 }, /* 100% ~= 5.00 Hz */ > + }, > +}; > + > static const struct i2c_device_id mlx90614_id[] = { > { "mlx90614", .driver_data = (kernel_ulong_t)&mlx90614_chip_info }, > + { "mlx90615", .driver_data = (kernel_ulong_t)&mlx90615_chip_info }, > { } > }; > MODULE_DEVICE_TABLE(i2c, mlx90614_id); > > static const struct of_device_id mlx90614_of_match[] = { > { .compatible = "melexis,mlx90614", .data = &mlx90614_chip_info }, > + { .compatible = "melexis,mlx90615", .data = &mlx90615_chip_info }, > { } > }; > MODULE_DEVICE_TABLE(of, mlx90614_of_match); > -- > 2.39.2 >
diff --git a/drivers/iio/temperature/mlx90614.c b/drivers/iio/temperature/mlx90614.c index 3aa108a652bb4..b2affcb795e00 100644 --- a/drivers/iio/temperature/mlx90614.c +++ b/drivers/iio/temperature/mlx90614.c @@ -1,12 +1,15 @@ // SPDX-License-Identifier: GPL-2.0-only /* - * mlx90614.c - Support for Melexis MLX90614 contactless IR temperature sensor + * mlx90614.c - Support for Melexis MLX90614/MLX90615 contactless IR temperature sensor * * Copyright (c) 2014 Peter Meerwald <pmeerw@pmeerw.net> * Copyright (c) 2015 Essensium NV * Copyright (c) 2015 Melexis * - * Driver for the Melexis MLX90614 I2C 16-bit IR thermopile sensor + * Driver for the Melexis MLX90614/MLX90615 I2C 16-bit IR thermopile sensor + * + * MLX90614 - 17-bit ADC + MLX90302 DSP + * MLX90615 - 16-bit ADC + MLX90325 DSP * * (7-bit I2C slave address 0x5a, 100KHz bus speed only!) * @@ -35,6 +38,10 @@ #define MLX90614_OP_EEPROM 0x20 #define MLX90614_OP_SLEEP 0xff +#define MLX90615_OP_EEPROM 0x10 +#define MLX90615_OP_RAM 0x20 +#define MLX90615_OP_SLEEP 0xc6 + /* Control bits in configuration register */ #define MLX90614_CONFIG_IIR_SHIFT 0 /* IIR coefficient */ #define MLX90614_CONFIG_IIR_MASK (0x7 << MLX90614_CONFIG_IIR_SHIFT) @@ -43,11 +50,16 @@ #define MLX90614_CONFIG_FIR_SHIFT 8 /* FIR coefficient */ #define MLX90614_CONFIG_FIR_MASK (0x7 << MLX90614_CONFIG_FIR_SHIFT) +#define MLX90615_CONFIG_IIR_SHIFT 12 /* IIR coefficient */ +#define MLX90615_CONFIG_IIR_MASK (0x7 << MLX90615_CONFIG_IIR_SHIFT) + /* Timings (in ms) */ #define MLX90614_TIMING_EEPROM 20 /* time for EEPROM write/erase to complete */ #define MLX90614_TIMING_WAKEUP 34 /* time to hold SDA low for wake-up */ #define MLX90614_TIMING_STARTUP 250 /* time before first data after wake-up */ +#define MLX90615_TIMING_WAKEUP 22 /* time to hold SCL low for wake-up */ + #define MLX90614_AUTOSLEEP_DELAY 5000 /* default autosleep delay */ /* Magic constants */ @@ -305,8 +317,8 @@ static int mlx90614_read_raw(struct iio_dev *indio_dev, *val2 = ret * NSEC_PER_SEC / chip_info->emissivity_max; } return IIO_VAL_INT_PLUS_NANO; - case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: /* IIR setting with - FIR = 1024 */ + /* IIR setting with FIR=1024 (MLX90614) or FIR=65536 (MLX90615) */ + case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: ret = mlx90614_power_get(data, false); if (ret < 0) return ret; @@ -664,14 +676,42 @@ static const struct mlx_chip_info mlx90614_chip_info = { }, }; +static const struct mlx_chip_info mlx90615_chip_info = { + .op_eeprom_emissivity = MLX90615_OP_EEPROM | 0x03, + .op_eeprom_config1 = MLX90615_OP_EEPROM | 0x02, + .op_ram_ta = MLX90615_OP_RAM | 0x06, + .op_ram_tobj1 = MLX90615_OP_RAM | 0x07, + .op_ram_tobj2 = MLX90615_OP_RAM | 0x08, + .op_sleep = MLX90615_OP_SLEEP, + .dual_channel = false, + .wakeup_delay_ms = MLX90615_TIMING_WAKEUP, + .emissivity_max = 16383, + .fir_config_mask = 0, /* MLX90615 FIR is fixed */ + .iir_config_mask = MLX90615_CONFIG_IIR_MASK, + /* IIR value 0 is FORBIDDEN COMBINATION on MLX90615 */ + .iir_valid_offset = 1, + .iir_values = { 500, 50, 30, 20, 15, 13, 10 }, + .iir_freqs = { + { 0, 100000 }, /* 14% ~= 0.10 Hz */ + { 0, 130000 }, /* 17% ~= 0.13 Hz */ + { 0, 150000 }, /* 20% ~= 0.15 Hz */ + { 0, 200000 }, /* 25% ~= 0.20 Hz */ + { 0, 300000 }, /* 33% ~= 0.30 Hz */ + { 0, 500000 }, /* 50% ~= 0.50 Hz */ + { 5, 000000 }, /* 100% ~= 5.00 Hz */ + }, +}; + static const struct i2c_device_id mlx90614_id[] = { { "mlx90614", .driver_data = (kernel_ulong_t)&mlx90614_chip_info }, + { "mlx90615", .driver_data = (kernel_ulong_t)&mlx90615_chip_info }, { } }; MODULE_DEVICE_TABLE(i2c, mlx90614_id); static const struct of_device_id mlx90614_of_match[] = { { .compatible = "melexis,mlx90614", .data = &mlx90614_chip_info }, + { .compatible = "melexis,mlx90615", .data = &mlx90615_chip_info }, { } }; MODULE_DEVICE_TABLE(of, mlx90614_of_match);
Add support for MLX90615 Infra Red Thermometer, which seems to be the predecesor of MLX90614 . There are significant differences in the register layout compared to MLX90614, but the functionality of the device is virtually identical. The following differences have been identified: - RAM/EEPROM/SLEEP access opcodes are different - RAM/EEPROM registers are at different offsets - EEPROM emissivity and configuration registers are at different offsets - EEPROM configuration register bits are shuffled around - EEPROM emissivity settings are 14 bit on MLX90615 , 16 bit on MLX90614 - MLX90615 can only ever support one sensor, MLX90614 could support two - FIR filter is set to fixed settings on MLX90615 - IIR filter coefficients are different This patch fills in the MLX90615 specific description and quirk handling. The IIR filter coefficients were provided by Melexis as follows: 0b0000 - Forbidden value 0b0001 - 100% - settling time = refresh rate = 205ms (around 5Hz) 0b0010 - 50% - settling time = 2050ms (around 0.5Hz) 0b0011 - 33% - settling time = 36900ms (around 0.3Hz) 0b0100 - 25% - settling time = 5125ms (around 0.2Hz) 0b0101 - 20% - settling time = 6355ms (around 0.15Hz) 0b0110 - 17% - settling time = 7790ms (around 0.13Hz) 0b0111 - 14% - settling time = 9225ms (around 0.1Hz) Signed-off-by: Marek Vasut <marex@denx.de> --- Cc: Crt Mori <cmo@melexis.com> Cc: Jonathan Cameron <jic23@kernel.org> Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Marek Vasut <marex@denx.de> Cc: Peter Meerwald <pmeerw@pmeerw.net> Cc: Rob Herring <robh+dt@kernel.org> Cc: devicetree@vger.kernel.org Cc: linux-iio@vger.kernel.org --- V2: Split the patch up into cleanups, abstraction and MLX90615 addition V3: Drop emissivity_res, update IIR filter coefficients per Melexis input --- drivers/iio/temperature/mlx90614.c | 48 +++++++++++++++++++++++++++--- 1 file changed, 44 insertions(+), 4 deletions(-)