@@ -183,4 +183,17 @@ config CPMAC
help
TI AR7 CPMAC Ethernet support
+config TI_ICSSG_PRUETH
+ tristate "TI Gigabit PRU Ethernet driver"
+ select PHYLIB
+ depends on PRU_REMOTEPROC
+ depends on ARCH_K3 && OF && TI_K3_UDMA_GLUE_LAYER
+ help
+ Support dual Gigabit Ethernet ports over the ICSSG PRU Subsystem.
+ This subsystem is available starting with the AM65 platform.
+
+ This driver requires firmware binaries which will run on the PRUs
+ to support the Ethernet operation. Currently, it supports Ethernet
+ with 1G and 100M link speed.
+
endif # NET_VENDOR_TI
@@ -28,3 +28,5 @@ obj-$(CONFIG_TI_K3_AM65_CPSW_NUSS) += ti-am65-cpsw-nuss.o
ti-am65-cpsw-nuss-y := am65-cpsw-nuss.o cpsw_sl.o am65-cpsw-ethtool.o cpsw_ale.o k3-cppi-desc-pool.o am65-cpsw-qos.o
ti-am65-cpsw-nuss-$(CONFIG_TI_K3_AM65_CPSW_SWITCHDEV) += am65-cpsw-switchdev.o
obj-$(CONFIG_TI_K3_AM65_CPTS) += am65-cpts.o
+obj-$(CONFIG_TI_ICSSG_PRUETH) += icssg-prueth.o
+icssg-prueth-y := icssg_prueth.o icssg_classifier.o icssg_ethtool.o icssg_queues.o icssg_config.o k3-cppi-desc-pool.o icssg_mii_cfg.o
new file mode 100644
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Texas Instruments ICSSG Ethernet Driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/types.h>
+#include <linux/regmap.h>
+
+#include "icssg_prueth.h"
+
+#define ICSSG_NUM_CLASSIFIERS 16
+#define ICSSG_NUM_FT1_SLOTS 8
+#define ICSSG_NUM_FT3_SLOTS 16
+
+#define ICSSG_NUM_CLASSIFIERS_IN_USE 5
+
+/* Filter 1 - FT1 */
+#define FT1_NUM_SLOTS 8
+#define FT1_SLOT_SIZE 0x10 /* bytes */
+
+/* offsets from FT1 slot base i.e. slot 1 start */
+#define FT1_DA0 0x0
+#define FT1_DA1 0x4
+#define FT1_DA0_MASK 0x8
+#define FT1_DA1_MASK 0xc
+
+#define FT1_N_REG(slize, n, reg) (offs[slice].ft1_slot_base + FT1_SLOT_SIZE * (n) + (reg))
+
+#define FT1_LEN_MASK GENMASK(19, 16)
+#define FT1_LEN_SHIFT 16
+#define FT1_LEN(len) (((len) << FT1_LEN_SHIFT) & FT1_LEN_MASK)
+#define FT1_START_MASK GENMASK(14, 0)
+#define FT1_START(start) ((start) & FT1_START_MASK)
+#define FT1_MATCH_SLOT(n) (GENMASK(23, 16) & (BIT(n) << 16))
+
+enum ft1_cfg_type {
+ FT1_CFG_TYPE_DISABLED = 0,
+ FT1_CFG_TYPE_EQ,
+ FT1_CFG_TYPE_GT,
+ FT1_CFG_TYPE_LT,
+};
+
+#define FT1_CFG_SHIFT(n) (2 * (n))
+#define FT1_CFG_MASK(n) (0x3 << FT1_CFG_SHIFT((n)))
+
+/* Filter 3 - FT3 */
+#define FT3_NUM_SLOTS 16
+#define FT3_SLOT_SIZE 0x20 /* bytes */
+
+/* offsets from FT3 slot n's base */
+#define FT3_START 0
+#define FT3_START_AUTO 0x4
+#define FT3_START_OFFSET 0x8
+#define FT3_JUMP_OFFSET 0xc
+#define FT3_LEN 0x10
+#define FT3_CFG 0x14
+#define FT3_T 0x18
+#define FT3_T_MASK 0x1c
+
+#define FT3_N_REG(slize, n, reg) (offs[slice].ft3_slot_base + FT3_SLOT_SIZE * (n) + (reg))
+
+/* offsets from rx_class n's base */
+#define RX_CLASS_AND_EN 0
+#define RX_CLASS_OR_EN 0x4
+#define RX_CLASS_NUM_SLOTS 16
+#define RX_CLASS_EN_SIZE 0x8 /* bytes */
+
+#define RX_CLASS_N_REG(slice, n, reg) (offs[slice].rx_class_base + RX_CLASS_EN_SIZE * (n) + (reg))
+
+/* RX Class Gates */
+#define RX_CLASS_GATES_SIZE 0x4 /* bytes */
+
+#define RX_CLASS_GATES_N_REG(slice, n) \
+ (offs[slice].rx_class_gates_base + RX_CLASS_GATES_SIZE * (n))
+
+#define RX_CLASS_GATES_ALLOW_MASK BIT(6)
+#define RX_CLASS_GATES_RAW_MASK BIT(5)
+#define RX_CLASS_GATES_PHASE_MASK BIT(4)
+
+/* RX Class traffic data matching bits */
+#define RX_CLASS_FT_UC BIT(31)
+#define RX_CLASS_FT_MC BIT(30)
+#define RX_CLASS_FT_BC BIT(29)
+#define RX_CLASS_FT_FW BIT(28)
+#define RX_CLASS_FT_RCV BIT(27)
+#define RX_CLASS_FT_VLAN BIT(26)
+#define RX_CLASS_FT_DA_P BIT(25)
+#define RX_CLASS_FT_DA_I BIT(24)
+#define RX_CLASS_FT_FT1_MATCH_MASK GENMASK(23, 16)
+#define RX_CLASS_FT_FT1_MATCH_SHIFT 16
+#define RX_CLASS_FT_FT3_MATCH_MASK GENMASK(15, 0)
+#define RX_CLASS_FT_FT3_MATCH_SHIFT 0
+
+#define RX_CLASS_FT_FT1_MATCH(slot) \
+ ((BIT(slot) << RX_CLASS_FT_FT1_MATCH_SHIFT) & RX_CLASS_FT_FT1_MATCH_MASK)
+
+enum rx_class_sel_type {
+ RX_CLASS_SEL_TYPE_OR = 0,
+ RX_CLASS_SEL_TYPE_AND = 1,
+ RX_CLASS_SEL_TYPE_OR_AND_AND = 2,
+ RX_CLASS_SEL_TYPE_OR_OR_AND = 3,
+};
+
+#define FT1_CFG_SHIFT(n) (2 * (n))
+#define FT1_CFG_MASK(n) (0x3 << FT1_CFG_SHIFT((n)))
+
+#define RX_CLASS_SEL_SHIFT(n) (2 * (n))
+#define RX_CLASS_SEL_MASK(n) (0x3 << RX_CLASS_SEL_SHIFT((n)))
+
+#define ICSSG_CFG_OFFSET 0
+#define MAC_INTERFACE_0 0x18
+#define MAC_INTERFACE_1 0x1c
+
+#define ICSSG_CFG_RX_L2_G_EN BIT(2)
+
+/* These are register offsets per PRU */
+struct miig_rt_offsets {
+ u32 mac0;
+ u32 mac1;
+ u32 ft1_start_len;
+ u32 ft1_cfg;
+ u32 ft1_slot_base;
+ u32 ft3_slot_base;
+ u32 ft3_p_base;
+ u32 ft_rx_ptr;
+ u32 rx_class_base;
+ u32 rx_class_cfg1;
+ u32 rx_class_cfg2;
+ u32 rx_class_gates_base;
+ u32 rx_green;
+ u32 rx_rate_cfg_base;
+ u32 rx_rate_src_sel0;
+ u32 rx_rate_src_sel1;
+ u32 tx_rate_cfg_base;
+ u32 stat_base;
+ u32 tx_hsr_tag;
+ u32 tx_hsr_seq;
+ u32 tx_vlan_type;
+ u32 tx_vlan_ins;
+};
+
+/* These are the offset values for miig_rt_offsets registers */
+static const struct miig_rt_offsets offs[] = {
+ /* PRU0 */
+ {
+ 0x8,
+ 0xc,
+ 0x80,
+ 0x84,
+ 0x88,
+ 0x108,
+ 0x308,
+ 0x408,
+ 0x40c,
+ 0x48c,
+ 0x490,
+ 0x494,
+ 0x4d4,
+ 0x4e4,
+ 0x504,
+ 0x508,
+ 0x50c,
+ 0x54c,
+ 0x63c,
+ 0x640,
+ 0x644,
+ 0x648,
+ },
+ /* PRU1 */
+ {
+ 0x10,
+ 0x14,
+ 0x64c,
+ 0x650,
+ 0x654,
+ 0x6d4,
+ 0x8d4,
+ 0x9d4,
+ 0x9d8,
+ 0xa58,
+ 0xa5c,
+ 0xa60,
+ 0xaa0,
+ 0xab0,
+ 0xad0,
+ 0xad4,
+ 0xad8,
+ 0xb18,
+ 0xc08,
+ 0xc0c,
+ 0xc10,
+ 0xc14,
+ },
+};
+
+static void rx_class_ft1_set_start_len(struct regmap *miig_rt, int slice,
+ u16 start, u8 len)
+{
+ u32 offset, val;
+
+ offset = offs[slice].ft1_start_len;
+ val = FT1_LEN(len) | FT1_START(start);
+ regmap_write(miig_rt, offset, val);
+}
+
+static void rx_class_ft1_set_da(struct regmap *miig_rt, int slice,
+ int n, const u8 *addr)
+{
+ u32 offset;
+
+ offset = FT1_N_REG(slice, n, FT1_DA0);
+ regmap_write(miig_rt, offset, (u32)(addr[0] | addr[1] << 8 |
+ addr[2] << 16 | addr[3] << 24));
+ offset = FT1_N_REG(slice, n, FT1_DA1);
+ regmap_write(miig_rt, offset, (u32)(addr[4] | addr[5] << 8));
+}
+
+static void rx_class_ft1_set_da_mask(struct regmap *miig_rt, int slice,
+ int n, const u8 *addr)
+{
+ u32 offset;
+
+ offset = FT1_N_REG(slice, n, FT1_DA0_MASK);
+ regmap_write(miig_rt, offset, (u32)(addr[0] | addr[1] << 8 |
+ addr[2] << 16 | addr[3] << 24));
+ offset = FT1_N_REG(slice, n, FT1_DA1_MASK);
+ regmap_write(miig_rt, offset, (u32)(addr[4] | addr[5] << 8));
+}
+
+static void rx_class_ft1_cfg_set_type(struct regmap *miig_rt, int slice, int n,
+ enum ft1_cfg_type type)
+{
+ u32 offset;
+
+ offset = offs[slice].ft1_cfg;
+ regmap_update_bits(miig_rt, offset, FT1_CFG_MASK(n),
+ type << FT1_CFG_SHIFT(n));
+}
+
+static void rx_class_sel_set_type(struct regmap *miig_rt, int slice, int n,
+ enum rx_class_sel_type type)
+{
+ u32 offset;
+
+ offset = offs[slice].rx_class_cfg1;
+ regmap_update_bits(miig_rt, offset, RX_CLASS_SEL_MASK(n),
+ type << RX_CLASS_SEL_SHIFT(n));
+}
+
+static void rx_class_set_and(struct regmap *miig_rt, int slice, int n,
+ u32 data)
+{
+ u32 offset;
+
+ offset = RX_CLASS_N_REG(slice, n, RX_CLASS_AND_EN);
+ regmap_write(miig_rt, offset, data);
+}
+
+static void rx_class_set_or(struct regmap *miig_rt, int slice, int n,
+ u32 data)
+{
+ u32 offset;
+
+ offset = RX_CLASS_N_REG(slice, n, RX_CLASS_OR_EN);
+ regmap_write(miig_rt, offset, data);
+}
+
+void icssg_class_set_host_mac_addr(struct regmap *miig_rt, const u8 *mac)
+{
+ regmap_write(miig_rt, MAC_INTERFACE_0, (u32)(mac[0] | mac[1] << 8 |
+ mac[2] << 16 | mac[3] << 24));
+ regmap_write(miig_rt, MAC_INTERFACE_1, (u32)(mac[4] | mac[5] << 8));
+}
+
+void icssg_class_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac)
+{
+ regmap_write(miig_rt, offs[slice].mac0, (u32)(mac[0] | mac[1] << 8 |
+ mac[2] << 16 | mac[3] << 24));
+ regmap_write(miig_rt, offs[slice].mac1, (u32)(mac[4] | mac[5] << 8));
+}
+
+/* disable all RX traffic */
+void icssg_class_disable(struct regmap *miig_rt, int slice)
+{
+ u32 data, offset;
+ int n;
+
+ /* Enable RX_L2_G */
+ regmap_update_bits(miig_rt, ICSSG_CFG_OFFSET, ICSSG_CFG_RX_L2_G_EN,
+ ICSSG_CFG_RX_L2_G_EN);
+
+ for (n = 0; n < ICSSG_NUM_CLASSIFIERS; n++) {
+ /* AND_EN = 0 */
+ rx_class_set_and(miig_rt, slice, n, 0);
+ /* OR_EN = 0 */
+ rx_class_set_or(miig_rt, slice, n, 0);
+
+ /* set CFG1 to OR */
+ rx_class_sel_set_type(miig_rt, slice, n, RX_CLASS_SEL_TYPE_OR);
+
+ /* configure gate */
+ offset = RX_CLASS_GATES_N_REG(slice, n);
+ regmap_read(miig_rt, offset, &data);
+ /* clear class_raw so we go through filters */
+ data &= ~RX_CLASS_GATES_RAW_MASK;
+ /* set allow and phase mask */
+ data |= RX_CLASS_GATES_ALLOW_MASK | RX_CLASS_GATES_PHASE_MASK;
+ regmap_write(miig_rt, offset, data);
+ }
+
+ /* FT1 Disabled */
+ for (n = 0; n < ICSSG_NUM_FT1_SLOTS; n++) {
+ const u8 addr[] = { 0, 0, 0, 0, 0, 0, };
+
+ rx_class_ft1_cfg_set_type(miig_rt, slice, n,
+ FT1_CFG_TYPE_DISABLED);
+ rx_class_ft1_set_da(miig_rt, slice, n, addr);
+ rx_class_ft1_set_da_mask(miig_rt, slice, n, addr);
+ }
+
+ /* clear CFG2 */
+ regmap_write(miig_rt, offs[slice].rx_class_cfg2, 0);
+}
+
+void icssg_class_default(struct regmap *miig_rt, int slice, bool allmulti)
+{
+ u32 data;
+
+ /* defaults */
+ icssg_class_disable(miig_rt, slice);
+
+ /* Setup Classifier */
+ /* match on Broadcast or MAC_PRU address */
+ data = RX_CLASS_FT_BC | RX_CLASS_FT_DA_P;
+
+ /* multicast */
+ if (allmulti)
+ data |= RX_CLASS_FT_MC;
+
+ rx_class_set_or(miig_rt, slice, 0, data);
+
+ /* set CFG1 for OR_OR_AND for classifier */
+ rx_class_sel_set_type(miig_rt, slice, 0, RX_CLASS_SEL_TYPE_OR_OR_AND);
+
+ /* clear CFG2 */
+ regmap_write(miig_rt, offs[slice].rx_class_cfg2, 0);
+}
+
+/* required for SAV check */
+void icssg_ft1_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac_addr)
+{
+ const u8 mask_addr[] = { 0, 0, 0, 0, 0, 0, };
+
+ rx_class_ft1_set_start_len(miig_rt, slice, 0, 6);
+ rx_class_ft1_set_da(miig_rt, slice, 0, mac_addr);
+ rx_class_ft1_set_da_mask(miig_rt, slice, 0, mask_addr);
+ rx_class_ft1_cfg_set_type(miig_rt, slice, 0, FT1_CFG_TYPE_EQ);
+}
new file mode 100644
@@ -0,0 +1,449 @@
+// SPDX-License-Identifier: GPL-2.0
+/* ICSSG Ethernet driver
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com
+ */
+
+#include <linux/iopoll.h>
+#include <linux/regmap.h>
+#include <uapi/linux/if_ether.h>
+#include "icssg_config.h"
+#include "icssg_prueth.h"
+#include "icssg_switch_map.h"
+#include "icssg_mii_rt.h"
+
+/* TX IPG Values to be set for 100M link speed. These values are
+ * in ocp_clk cycles. So need change if ocp_clk is changed for a specific
+ * h/w design.
+ */
+
+/* IPG is in core_clk cycles */
+#define MII_RT_TX_IPG_100M 0x17
+#define MII_RT_TX_IPG_1G 0xb
+
+#define ICSSG_QUEUES_MAX 64
+#define ICSSG_QUEUE_OFFSET 0xd00
+#define ICSSG_QUEUE_PEEK_OFFSET 0xe00
+#define ICSSG_QUEUE_CNT_OFFSET 0xe40
+#define ICSSG_QUEUE_RESET_OFFSET 0xf40
+
+#define ICSSG_NUM_TX_QUEUES 8
+
+#define RECYCLE_Q_SLICE0 16
+#define RECYCLE_Q_SLICE1 17
+
+#define ICSSG_NUM_OTHER_QUEUES 5 /* port, host and special queues */
+
+#define PORT_HI_Q_SLICE0 32
+#define PORT_LO_Q_SLICE0 33
+#define HOST_HI_Q_SLICE0 34
+#define HOST_LO_Q_SLICE0 35
+#define HOST_SPL_Q_SLICE0 40 /* Special Queue */
+
+#define PORT_HI_Q_SLICE1 36
+#define PORT_LO_Q_SLICE1 37
+#define HOST_HI_Q_SLICE1 38
+#define HOST_LO_Q_SLICE1 39
+#define HOST_SPL_Q_SLICE1 41 /* Special Queue */
+
+#define MII_RXCFG_DEFAULT (PRUSS_MII_RT_RXCFG_RX_ENABLE | \
+ PRUSS_MII_RT_RXCFG_RX_DATA_RDY_MODE_DIS | \
+ PRUSS_MII_RT_RXCFG_RX_L2_EN | \
+ PRUSS_MII_RT_RXCFG_RX_L2_EOF_SCLR_DIS)
+
+#define MII_TXCFG_DEFAULT (PRUSS_MII_RT_TXCFG_TX_ENABLE | \
+ PRUSS_MII_RT_TXCFG_TX_AUTO_PREAMBLE | \
+ PRUSS_MII_RT_TXCFG_TX_32_MODE_EN | \
+ PRUSS_MII_RT_TXCFG_TX_IPG_WIRE_CLK_EN)
+
+#define ICSSG_CFG_DEFAULT (ICSSG_CFG_TX_L1_EN | \
+ ICSSG_CFG_TX_L2_EN | ICSSG_CFG_RX_L2_G_EN | \
+ ICSSG_CFG_TX_PRU_EN | \
+ ICSSG_CFG_SGMII_MODE)
+
+#define FDB_GEN_CFG1 0x60
+#define SMEM_VLAN_OFFSET 8
+#define SMEM_VLAN_OFFSET_MASK GENMASK(25, 8)
+
+#define FDB_GEN_CFG2 0x64
+#define FDB_VLAN_EN BIT(6)
+#define FDB_HOST_EN BIT(2)
+#define FDB_PRU1_EN BIT(1)
+#define FDB_PRU0_EN BIT(0)
+#define FDB_EN_ALL (FDB_PRU0_EN | FDB_PRU1_EN | \
+ FDB_HOST_EN | FDB_VLAN_EN)
+
+/**
+ * struct map - ICSSG Queue Map
+ * @queue: Queue number
+ * @pd_addr_start: Packet descriptor queue reserved memory
+ * @flags: Flags
+ * @special: Indicates whether this queue is a special queue or not
+ */
+struct map {
+ int queue;
+ u32 pd_addr_start;
+ u32 flags;
+ bool special;
+};
+
+/* Hardware queue map for ICSSG */
+const struct map hwq_map[2][ICSSG_NUM_OTHER_QUEUES] = {
+ {
+ { PORT_HI_Q_SLICE0, PORT_DESC0_HI, 0x200000, 0 },
+ { PORT_LO_Q_SLICE0, PORT_DESC0_LO, 0, 0 },
+ { HOST_HI_Q_SLICE0, HOST_DESC0_HI, 0x200000, 0 },
+ { HOST_LO_Q_SLICE0, HOST_DESC0_LO, 0, 0 },
+ { HOST_SPL_Q_SLICE0, HOST_SPPD0, 0x400000, 1 },
+ },
+ {
+ { PORT_HI_Q_SLICE1, PORT_DESC1_HI, 0xa00000, 0 },
+ { PORT_LO_Q_SLICE1, PORT_DESC1_LO, 0x800000, 0 },
+ { HOST_HI_Q_SLICE1, HOST_DESC1_HI, 0xa00000, 0 },
+ { HOST_LO_Q_SLICE1, HOST_DESC1_LO, 0x800000, 0 },
+ { HOST_SPL_Q_SLICE1, HOST_SPPD1, 0xc00000, 1 },
+ },
+};
+
+static void icssg_config_mii_init(struct prueth_emac *emac)
+{
+ u32 rxcfg, txcfg, rxcfg_reg, txcfg_reg, pcnt_reg;
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+ struct regmap *mii_rt;
+
+ mii_rt = prueth->mii_rt;
+
+ rxcfg_reg = (slice == ICSS_MII0) ? PRUSS_MII_RT_RXCFG0 :
+ PRUSS_MII_RT_RXCFG1;
+ txcfg_reg = (slice == ICSS_MII0) ? PRUSS_MII_RT_TXCFG0 :
+ PRUSS_MII_RT_TXCFG1;
+ pcnt_reg = (slice == ICSS_MII0) ? PRUSS_MII_RT_RX_PCNT0 :
+ PRUSS_MII_RT_RX_PCNT1;
+
+ rxcfg = MII_RXCFG_DEFAULT;
+ txcfg = MII_TXCFG_DEFAULT;
+
+ if (slice == ICSS_MII1)
+ rxcfg |= PRUSS_MII_RT_RXCFG_RX_MUX_SEL;
+
+ /* In MII mode TX lines swapped inside ICSSG, so TX_MUX_SEL cfg need
+ * to be swapped also comparing to RGMII mode.
+ */
+ if (emac->phy_if == PHY_INTERFACE_MODE_MII && slice == ICSS_MII0)
+ txcfg |= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;
+ else if (emac->phy_if != PHY_INTERFACE_MODE_MII && slice == ICSS_MII1)
+ txcfg |= PRUSS_MII_RT_TXCFG_TX_MUX_SEL;
+
+ regmap_write(mii_rt, rxcfg_reg, rxcfg);
+ regmap_write(mii_rt, txcfg_reg, txcfg);
+ regmap_write(mii_rt, pcnt_reg, 0x1);
+}
+
+static void icssg_miig_queues_init(struct prueth *prueth, int slice)
+{
+ struct regmap *miig_rt = prueth->miig_rt;
+ void __iomem *smem = prueth->shram.va;
+ u8 pd[ICSSG_SPECIAL_PD_SIZE];
+ int queue = 0, i, j;
+ u32 *pdword;
+
+ /* reset hwqueues */
+ if (slice)
+ queue = ICSSG_NUM_TX_QUEUES;
+
+ for (i = 0; i < ICSSG_NUM_TX_QUEUES; i++) {
+ regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET, queue);
+ queue++;
+ }
+
+ queue = slice ? RECYCLE_Q_SLICE1 : RECYCLE_Q_SLICE0;
+ regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET, queue);
+
+ for (i = 0; i < ICSSG_NUM_OTHER_QUEUES; i++) {
+ regmap_write(miig_rt, ICSSG_QUEUE_RESET_OFFSET,
+ hwq_map[slice][i].queue);
+ }
+
+ /* initialize packet descriptors in SMEM */
+ /* push pakcet descriptors to hwqueues */
+
+ pdword = (u32 *)pd;
+ for (j = 0; j < ICSSG_NUM_OTHER_QUEUES; j++) {
+ const struct map *mp;
+ int pd_size, num_pds;
+ u32 pdaddr;
+
+ mp = &hwq_map[slice][j];
+ if (mp->special) {
+ pd_size = ICSSG_SPECIAL_PD_SIZE;
+ num_pds = ICSSG_NUM_SPECIAL_PDS;
+ } else {
+ pd_size = ICSSG_NORMAL_PD_SIZE;
+ num_pds = ICSSG_NUM_NORMAL_PDS;
+ }
+
+ for (i = 0; i < num_pds; i++) {
+ memset(pd, 0, pd_size);
+
+ pdword[0] &= cpu_to_le32(ICSSG_FLAG_MASK);
+ pdword[0] |= cpu_to_le32(mp->flags);
+ pdaddr = mp->pd_addr_start + i * pd_size;
+
+ memcpy_toio(smem + pdaddr, pd, pd_size);
+ queue = mp->queue;
+ regmap_write(miig_rt, ICSSG_QUEUE_OFFSET + 4 * queue,
+ pdaddr);
+ }
+ }
+}
+
+void icssg_config_ipg(struct prueth_emac *emac)
+{
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+
+ switch (emac->speed) {
+ case SPEED_1000:
+ icssg_mii_update_ipg(prueth->mii_rt, slice, MII_RT_TX_IPG_1G);
+ break;
+ case SPEED_100:
+ icssg_mii_update_ipg(prueth->mii_rt, slice, MII_RT_TX_IPG_100M);
+ break;
+ default:
+ /* Other links speeds not supported */
+ netdev_err(emac->ndev, "Unsupported link speed\n");
+ return;
+ }
+}
+
+static void emac_r30_cmd_init(struct prueth_emac *emac)
+{
+ struct icssg_r30_cmd *p;
+ int i;
+
+ p = emac->dram.va + MGR_R30_CMD_OFFSET;
+
+ for (i = 0; i < 4; i++)
+ writel(EMAC_NONE, &p->cmd[i]);
+}
+
+static int emac_r30_is_done(struct prueth_emac *emac)
+{
+ const struct icssg_r30_cmd *p;
+ u32 cmd;
+ int i;
+
+ p = emac->dram.va + MGR_R30_CMD_OFFSET;
+
+ for (i = 0; i < 4; i++) {
+ cmd = readl(&p->cmd[i]);
+ if (cmd != EMAC_NONE)
+ return 0;
+ }
+
+ return 1;
+}
+
+static int prueth_emac_buffer_setup(struct prueth_emac *emac)
+{
+ struct icssg_buffer_pool_cfg *bpool_cfg;
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+ struct icssg_rxq_ctx *rxq_ctx;
+ u32 addr;
+ int i;
+
+ /* Layout to have 64KB aligned buffer pool
+ * |BPOOL0|BPOOL1|RX_CTX0|RX_CTX1|
+ */
+
+ addr = lower_32_bits(prueth->msmcram.pa);
+ if (slice)
+ addr += PRUETH_NUM_BUF_POOLS * PRUETH_EMAC_BUF_POOL_SIZE;
+
+ if (addr % SZ_64K) {
+ dev_warn(prueth->dev, "buffer pool needs to be 64KB aligned\n");
+ return -EINVAL;
+ }
+
+ bpool_cfg = emac->dram.va + BUFFER_POOL_0_ADDR_OFFSET;
+ /* workaround for f/w bug. bpool 0 needs to be initilalized */
+ bpool_cfg[0].addr = cpu_to_le32(addr);
+ bpool_cfg[0].len = 0;
+
+ for (i = PRUETH_EMAC_BUF_POOL_START;
+ i < PRUETH_EMAC_BUF_POOL_START + PRUETH_NUM_BUF_POOLS;
+ i++) {
+ bpool_cfg[i].addr = cpu_to_le32(addr);
+ bpool_cfg[i].len = cpu_to_le32(PRUETH_EMAC_BUF_POOL_SIZE);
+ addr += PRUETH_EMAC_BUF_POOL_SIZE;
+ }
+
+ if (!slice)
+ addr += PRUETH_NUM_BUF_POOLS * PRUETH_EMAC_BUF_POOL_SIZE;
+ else
+ addr += PRUETH_EMAC_RX_CTX_BUF_SIZE * 2;
+
+ /* Pre-emptible RX buffer queue */
+ rxq_ctx = emac->dram.va + HOST_RX_Q_PRE_CONTEXT_OFFSET;
+ for (i = 0; i < 3; i++)
+ rxq_ctx->start[i] = cpu_to_le32(addr);
+
+ addr += PRUETH_EMAC_RX_CTX_BUF_SIZE;
+ rxq_ctx->end = cpu_to_le32(addr);
+
+ /* Express RX buffer queue */
+ rxq_ctx = emac->dram.va + HOST_RX_Q_EXP_CONTEXT_OFFSET;
+ for (i = 0; i < 3; i++)
+ rxq_ctx->start[i] = cpu_to_le32(addr);
+
+ addr += PRUETH_EMAC_RX_CTX_BUF_SIZE;
+ rxq_ctx->end = cpu_to_le32(addr);
+
+ return 0;
+}
+
+static void icssg_init_emac_mode(struct prueth *prueth)
+{
+ /* When the device is configured as a bridge and it is being brought back
+ * to the emac mode, the host mac address has to be set as 0.
+ */
+ u8 mac[ETH_ALEN] = { 0 };
+
+ if (prueth->emacs_initialized)
+ return;
+
+ regmap_update_bits(prueth->miig_rt, FDB_GEN_CFG1, SMEM_VLAN_OFFSET_MASK, 0);
+ regmap_write(prueth->miig_rt, FDB_GEN_CFG2, 0);
+ /* Clear host MAC address */
+ icssg_class_set_host_mac_addr(prueth->miig_rt, mac);
+}
+
+int icssg_config(struct prueth *prueth, struct prueth_emac *emac, int slice)
+{
+ void *config = emac->dram.va + ICSSG_CONFIG_OFFSET;
+ struct icssg_flow_cfg *flow_cfg;
+ u8 *cfg_byte_ptr = config;
+ int ret;
+
+ icssg_init_emac_mode(prueth);
+
+ memset_io(config, 0, TAS_GATE_MASK_LIST0);
+ icssg_miig_queues_init(prueth, slice);
+
+ emac->speed = SPEED_1000;
+ emac->duplex = DUPLEX_FULL;
+ if (!phy_interface_mode_is_rgmii(emac->phy_if)) {
+ emac->speed = SPEED_100;
+ emac->duplex = DUPLEX_FULL;
+ }
+ regmap_update_bits(prueth->miig_rt, ICSSG_CFG_OFFSET, ICSSG_CFG_DEFAULT, ICSSG_CFG_DEFAULT);
+ icssg_miig_set_interface_mode(prueth->miig_rt, slice, emac->phy_if);
+ icssg_config_mii_init(emac);
+ icssg_config_ipg(emac);
+ icssg_update_rgmii_cfg(prueth->miig_rt, emac);
+
+ /* set GPI mode */
+ pruss_cfg_gpimode(prueth->pruss, prueth->pru_id[slice],
+ PRUSS_GPI_MODE_MII);
+
+ /* enable XFR shift for PRU and RTU */
+ pruss_cfg_xfr_enable(prueth->pruss, PRU_TYPE_PRU, true);
+ pruss_cfg_xfr_enable(prueth->pruss, PRU_TYPE_RTU, true);
+
+ /* set C28 to 0x100 */
+ pru_rproc_set_ctable(prueth->pru[slice], PRU_C28, 0x100 << 8);
+ pru_rproc_set_ctable(prueth->rtu[slice], PRU_C28, 0x100 << 8);
+ pru_rproc_set_ctable(prueth->txpru[slice], PRU_C28, 0x100 << 8);
+
+ flow_cfg = config + PSI_L_REGULAR_FLOW_ID_BASE_OFFSET;
+ flow_cfg->rx_base_flow = cpu_to_le32(emac->rx_flow_id_base);
+ flow_cfg->mgm_base_flow = 0;
+ *(cfg_byte_ptr + SPL_PKT_DEFAULT_PRIORITY) = 0;
+ *(cfg_byte_ptr + QUEUE_NUM_UNTAGGED) = 0x0;
+
+ ret = prueth_emac_buffer_setup(emac);
+ if (ret)
+ return ret;
+
+ emac_r30_cmd_init(emac);
+
+ return 0;
+}
+
+/* Bitmask for ICSSG r30 commands */
+static const struct icssg_r30_cmd emac_r32_bitmask[] = {
+ {{0xffff0004, 0xffff0100, 0xffff0100, EMAC_NONE}}, /* EMAC_PORT_DISABLE */
+ {{0xfffb0040, 0xfeff0200, 0xfeff0200, EMAC_NONE}}, /* EMAC_PORT_BLOCK */
+ {{0xffbb0000, 0xfcff0000, 0xdcff0000, EMAC_NONE}}, /* EMAC_PORT_FORWARD */
+ {{0xffbb0000, 0xfcff0000, 0xfcff2000, EMAC_NONE}}, /* EMAC_PORT_FORWARD_WO_LEARNING */
+ {{0xffff0001, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT ALL */
+ {{0xfffe0002, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT TAGGED */
+ {{0xfffc0000, EMAC_NONE, EMAC_NONE, EMAC_NONE}}, /* ACCEPT UNTAGGED and PRIO */
+ {{EMAC_NONE, 0xffff0020, EMAC_NONE, EMAC_NONE}}, /* TAS Trigger List change */
+ {{EMAC_NONE, 0xdfff1000, EMAC_NONE, EMAC_NONE}}, /* TAS set state ENABLE*/
+ {{EMAC_NONE, 0xefff2000, EMAC_NONE, EMAC_NONE}}, /* TAS set state RESET*/
+ {{EMAC_NONE, 0xcfff0000, EMAC_NONE, EMAC_NONE}}, /* TAS set state DISABLE*/
+ {{EMAC_NONE, EMAC_NONE, 0xffff0400, EMAC_NONE}}, /* UC flooding ENABLE*/
+ {{EMAC_NONE, EMAC_NONE, 0xfbff0000, EMAC_NONE}}, /* UC flooding DISABLE*/
+ {{EMAC_NONE, EMAC_NONE, 0xffff0800, EMAC_NONE}}, /* MC flooding ENABLE*/
+ {{EMAC_NONE, EMAC_NONE, 0xf7ff0000, EMAC_NONE}}, /* MC flooding DISABLE*/
+ {{EMAC_NONE, 0xffff4000, EMAC_NONE, EMAC_NONE}}, /* Preemption on Tx ENABLE*/
+ {{EMAC_NONE, 0xbfff0000, EMAC_NONE, EMAC_NONE}}, /* Preemption on Tx DISABLE*/
+ {{0xffff0010, EMAC_NONE, 0xffff0010, EMAC_NONE}}, /* VLAN AWARE*/
+ {{0xffef0000, EMAC_NONE, 0xffef0000, EMAC_NONE}} /* VLAN UNWARE*/
+};
+
+int emac_set_port_state(struct prueth_emac *emac,
+ enum icssg_port_state_cmd cmd)
+{
+ struct icssg_r30_cmd *p;
+ int ret = -ETIMEDOUT;
+ int done = 0;
+ int i;
+
+ p = emac->dram.va + MGR_R30_CMD_OFFSET;
+
+ if (cmd >= ICSSG_EMAC_PORT_MAX_COMMANDS) {
+ netdev_err(emac->ndev, "invalid port command\n");
+ return -EINVAL;
+ }
+
+ /* only one command at a time allowed to firmware */
+ mutex_lock(&emac->cmd_lock);
+
+ for (i = 0; i < 4; i++)
+ writel(emac_r32_bitmask[cmd].cmd[i], &p->cmd[i]);
+
+ /* wait for done */
+ ret = read_poll_timeout(emac_r30_is_done, done, done == 1,
+ 1000, 10000, false, emac);
+
+ if (ret == -ETIMEDOUT)
+ netdev_err(emac->ndev, "timeout waiting for command done\n");
+
+ mutex_unlock(&emac->cmd_lock);
+
+ return ret;
+}
+
+void icssg_config_set_speed(struct prueth_emac *emac)
+{
+ u8 fw_speed;
+
+ switch (emac->speed) {
+ case SPEED_1000:
+ fw_speed = FW_LINK_SPEED_1G;
+ break;
+ case SPEED_100:
+ fw_speed = FW_LINK_SPEED_100M;
+ break;
+ default:
+ /* Other links speeds not supported */
+ netdev_err(emac->ndev, "Unsupported link speed\n");
+ return;
+ }
+
+ writeb(fw_speed, emac->dram.va + PORT_LINK_SPEED_OFFSET);
+}
new file mode 100644
@@ -0,0 +1,200 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#ifndef __NET_TI_ICSSG_CONFIG_H
+#define __NET_TI_ICSSG_CONFIG_H
+
+struct icssg_buffer_pool_cfg {
+ __le32 addr;
+ __le32 len;
+} __packed;
+
+struct icssg_flow_cfg {
+ __le16 rx_base_flow;
+ __le16 mgm_base_flow;
+} __packed;
+
+#define PRUETH_PKT_TYPE_CMD 0x10
+#define PRUETH_NAV_PS_DATA_SIZE 16 /* Protocol specific data size */
+#define PRUETH_NAV_SW_DATA_SIZE 16 /* SW related data size */
+#define PRUETH_MAX_TX_DESC 512
+#define PRUETH_MAX_RX_DESC 512
+#define PRUETH_MAX_RX_FLOWS 1 /* excluding default flow */
+#define PRUETH_RX_FLOW_DATA 0
+
+#define PRUETH_EMAC_BUF_POOL_SIZE SZ_8K
+#define PRUETH_EMAC_POOLS_PER_SLICE 24
+#define PRUETH_EMAC_BUF_POOL_START 8
+#define PRUETH_NUM_BUF_POOLS 8
+#define PRUETH_EMAC_RX_CTX_BUF_SIZE SZ_16K /* per slice */
+#define MSMC_RAM_SIZE \
+ (2 * (PRUETH_EMAC_BUF_POOL_SIZE * PRUETH_NUM_BUF_POOLS + \
+ PRUETH_EMAC_RX_CTX_BUF_SIZE * 2))
+
+struct icssg_rxq_ctx {
+ __le32 start[3];
+ __le32 end;
+} __packed;
+
+/* Load time Fiwmware Configuration */
+
+#define ICSSG_FW_MGMT_CMD_HEADER 0x81
+#define ICSSG_FW_MGMT_FDB_CMD_TYPE 0x03
+#define ICSSG_FW_MGMT_CMD_TYPE 0x04
+#define ICSSG_FW_MGMT_PKT 0x80000000
+
+struct icssg_r30_cmd {
+ u32 cmd[4];
+} __packed;
+
+enum icssg_port_state_cmd {
+ ICSSG_EMAC_PORT_DISABLE = 0,
+ ICSSG_EMAC_PORT_BLOCK,
+ ICSSG_EMAC_PORT_FORWARD,
+ ICSSG_EMAC_PORT_FORWARD_WO_LEARNING,
+ ICSSG_EMAC_PORT_ACCEPT_ALL,
+ ICSSG_EMAC_PORT_ACCEPT_TAGGED,
+ ICSSG_EMAC_PORT_ACCEPT_UNTAGGED_N_PRIO,
+ ICSSG_EMAC_PORT_TAS_TRIGGER,
+ ICSSG_EMAC_PORT_TAS_ENABLE,
+ ICSSG_EMAC_PORT_TAS_RESET,
+ ICSSG_EMAC_PORT_TAS_DISABLE,
+ ICSSG_EMAC_PORT_UC_FLOODING_ENABLE,
+ ICSSG_EMAC_PORT_UC_FLOODING_DISABLE,
+ ICSSG_EMAC_PORT_MC_FLOODING_ENABLE,
+ ICSSG_EMAC_PORT_MC_FLOODING_DISABLE,
+ ICSSG_EMAC_PORT_PREMPT_TX_ENABLE,
+ ICSSG_EMAC_PORT_PREMPT_TX_DISABLE,
+ ICSSG_EMAC_PORT_VLAN_AWARE_ENABLE,
+ ICSSG_EMAC_PORT_VLAN_AWARE_DISABLE,
+ ICSSG_EMAC_PORT_MAX_COMMANDS
+};
+
+#define EMAC_NONE 0xffff0000
+#define EMAC_PRU0_P_DI 0xffff0004
+#define EMAC_PRU1_P_DI 0xffff0040
+#define EMAC_TX_P_DI 0xffff0100
+
+#define EMAC_PRU0_P_EN 0xfffb0000
+#define EMAC_PRU1_P_EN 0xffbf0000
+#define EMAC_TX_P_EN 0xfeff0000
+
+#define EMAC_P_BLOCK 0xffff0040
+#define EMAC_TX_P_BLOCK 0xffff0200
+#define EMAC_P_UNBLOCK 0xffbf0000
+#define EMAC_TX_P_UNBLOCK 0xfdff0000
+#define EMAC_LEAN_EN 0xfff70000
+#define EMAC_LEAN_DI 0xffff0008
+
+#define EMAC_ACCEPT_ALL 0xffff0001
+#define EMAC_ACCEPT_TAG 0xfffe0002
+#define EMAC_ACCEPT_PRIOR 0xfffc0000
+
+/* Config area lies in DRAM */
+#define ICSSG_CONFIG_OFFSET 0x0
+
+/* Config area lies in shared RAM */
+#define ICSSG_CONFIG_OFFSET_SLICE0 0
+#define ICSSG_CONFIG_OFFSET_SLICE1 0x8000
+
+#define ICSSG_NUM_NORMAL_PDS 64
+#define ICSSG_NUM_SPECIAL_PDS 16
+
+#define ICSSG_NORMAL_PD_SIZE 8
+#define ICSSG_SPECIAL_PD_SIZE 20
+
+#define ICSSG_FLAG_MASK 0xff00ffff
+
+struct icssg_setclock_desc {
+ u8 request;
+ u8 restore;
+ u8 acknowledgment;
+ u8 cmp_status;
+ u32 margin;
+ u32 cyclecounter0_set;
+ u32 cyclecounter1_set;
+ u32 iepcount_set;
+ u32 rsvd1;
+ u32 rsvd2;
+ u32 CMP0_current;
+ u32 iepcount_current;
+ u32 difference;
+ u32 cyclecounter0_new;
+ u32 cyclecounter1_new;
+ u32 CMP0_new;
+} __packed;
+
+#define ICSSG_CMD_POP_SLICE0 56
+#define ICSSG_CMD_POP_SLICE1 60
+
+#define ICSSG_CMD_PUSH_SLICE0 57
+#define ICSSG_CMD_PUSH_SLICE1 61
+
+#define ICSSG_RSP_POP_SLICE0 58
+#define ICSSG_RSP_POP_SLICE1 62
+
+#define ICSSG_RSP_PUSH_SLICE0 56
+#define ICSSG_RSP_PUSH_SLICE1 60
+
+#define ICSSG_TS_POP_SLICE0 59
+#define ICSSG_TS_POP_SLICE1 63
+
+#define ICSSG_TS_PUSH_SLICE0 40
+#define ICSSG_TS_PUSH_SLICE1 41
+
+/* FDB FID_C2 flag definitions */
+/* Indicates host port membership.*/
+#define ICSSG_FDB_ENTRY_P0_MEMBERSHIP BIT(0)
+/* Indicates that MAC ID is connected to physical port 1 */
+#define ICSSG_FDB_ENTRY_P1_MEMBERSHIP BIT(1)
+/* Indicates that MAC ID is connected to physical port 2 */
+#define ICSSG_FDB_ENTRY_P2_MEMBERSHIP BIT(2)
+/* Ageable bit is set for learned entries and cleared for static entries */
+#define ICSSG_FDB_ENTRY_AGEABLE BIT(3)
+/* If set for DA then packet is determined to be a special packet */
+#define ICSSG_FDB_ENTRY_BLOCK BIT(4)
+/* If set for DA then the SA from the packet is not learned */
+#define ICSSG_FDB_ENTRY_SECURE BIT(5)
+/* If set, it means packet has been seen recently with source address + FID
+ * matching MAC address/FID of entry
+ */
+#define ICSSG_FDB_ENTRY_TOUCHED BIT(6)
+/* Set if entry is valid */
+#define ICSSG_FDB_ENTRY_VALID BIT(7)
+
+/**
+ * struct prueth_vlan_tbl - VLAN table entries struct in ICSSG SMEM
+ * @fid_c1: membership and forwarding rules flag to this table. See
+ * above to defines for bit definitions
+ * @fid: FDB index for this VID (there is 1-1 mapping b/w VID and FID)
+ */
+struct prueth_vlan_tbl {
+ u8 fid_c1;
+ u8 fid;
+} __packed;
+
+/**
+ * struct prueth_fdb_slot - Result of FDB slot lookup
+ * @mac: MAC address
+ * @fid: fid to be associated with MAC
+ * @fid_c2: FID_C2 entry for this MAC
+ */
+struct prueth_fdb_slot {
+ u8 mac[ETH_ALEN];
+ u8 fid;
+ u8 fid_c2;
+} __packed;
+
+enum icssg_ietfpe_verify_states {
+ ICSSG_IETFPE_STATE_UNKNOWN = 0,
+ ICSSG_IETFPE_STATE_INITIAL,
+ ICSSG_IETFPE_STATE_VERIFYING,
+ ICSSG_IETFPE_STATE_SUCCEEDED,
+ ICSSG_IETFPE_STATE_FAILED,
+ ICSSG_IETFPE_STATE_DISABLED
+};
+#endif /* __NET_TI_ICSSG_CONFIG_H */
new file mode 100644
@@ -0,0 +1,325 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include "icssg_prueth.h"
+#include <linux/regmap.h>
+
+static const u32 stats_base[] = { 0x54c, /* Slice 0 stats start */
+ 0xb18, /* Slice 1 stats start */
+};
+
+/* ICSSG MIIG_STATS registers */
+struct miig_stats_regs {
+ /* Rx */
+ u32 rx_good_frames;
+ u32 rx_broadcast_frames;
+ u32 rx_multicast_frames;
+ u32 rx_crc_error_frames;
+ u32 rx_mii_error_frames;
+ u32 rx_odd_nibble_frames;
+ u32 rx_frame_max_size;
+ u32 rx_max_size_error_frames;
+ u32 rx_frame_min_size;
+ u32 rx_min_size_error_frames;
+ u32 rx_overrun_frames;
+ u32 rx_class0_hits;
+ u32 rx_class1_hits;
+ u32 rx_class2_hits;
+ u32 rx_class3_hits;
+ u32 rx_class4_hits;
+ u32 rx_class5_hits;
+ u32 rx_class6_hits;
+ u32 rx_class7_hits;
+ u32 rx_class8_hits;
+ u32 rx_class9_hits;
+ u32 rx_class10_hits;
+ u32 rx_class11_hits;
+ u32 rx_class12_hits;
+ u32 rx_class13_hits;
+ u32 rx_class14_hits;
+ u32 rx_class15_hits;
+ u32 rx_smd_frags;
+ u32 rx_bucket1_size;
+ u32 rx_bucket2_size;
+ u32 rx_bucket3_size;
+ u32 rx_bucket4_size;
+ u32 rx_64B_frames;
+ u32 rx_bucket1_frames;
+ u32 rx_bucket2_frames;
+ u32 rx_bucket3_frames;
+ u32 rx_bucket4_frames;
+ u32 rx_bucket5_frames;
+ u32 rx_total_bytes;
+ u32 rx_tx_total_bytes;
+ /* Tx */
+ u32 tx_good_frames;
+ u32 tx_broadcast_frames;
+ u32 tx_multicast_frames;
+ u32 tx_odd_nibble_frames;
+ u32 tx_underflow_errors;
+ u32 tx_frame_max_size;
+ u32 tx_max_size_error_frames;
+ u32 tx_frame_min_size;
+ u32 tx_min_size_error_frames;
+ u32 tx_bucket1_size;
+ u32 tx_bucket2_size;
+ u32 tx_bucket3_size;
+ u32 tx_bucket4_size;
+ u32 tx_64B_frames;
+ u32 tx_bucket1_frames;
+ u32 tx_bucket2_frames;
+ u32 tx_bucket3_frames;
+ u32 tx_bucket4_frames;
+ u32 tx_bucket5_frames;
+ u32 tx_total_bytes;
+};
+
+#define ICSSG_STATS(field) \
+{ \
+ #field, \
+ offsetof(struct miig_stats_regs, field), \
+}
+
+/**
+ * struct icssg_stats - ICSSG Stats structure
+ * @name: Stats name
+ * @offset: ICSSG stats register offset
+ */
+struct icssg_stats {
+ char name[ETH_GSTRING_LEN];
+ u32 offset;
+};
+
+static const struct icssg_stats icssg_ethtool_stats[] = {
+ /* Rx */
+ ICSSG_STATS(rx_good_frames),
+ ICSSG_STATS(rx_broadcast_frames),
+ ICSSG_STATS(rx_multicast_frames),
+ ICSSG_STATS(rx_crc_error_frames),
+ ICSSG_STATS(rx_mii_error_frames),
+ ICSSG_STATS(rx_odd_nibble_frames),
+ ICSSG_STATS(rx_frame_max_size),
+ ICSSG_STATS(rx_max_size_error_frames),
+ ICSSG_STATS(rx_frame_min_size),
+ ICSSG_STATS(rx_min_size_error_frames),
+ ICSSG_STATS(rx_overrun_frames),
+ ICSSG_STATS(rx_class0_hits),
+ ICSSG_STATS(rx_class1_hits),
+ ICSSG_STATS(rx_class2_hits),
+ ICSSG_STATS(rx_class3_hits),
+ ICSSG_STATS(rx_class4_hits),
+ ICSSG_STATS(rx_class5_hits),
+ ICSSG_STATS(rx_class6_hits),
+ ICSSG_STATS(rx_class7_hits),
+ ICSSG_STATS(rx_class8_hits),
+ ICSSG_STATS(rx_class9_hits),
+ ICSSG_STATS(rx_class10_hits),
+ ICSSG_STATS(rx_class11_hits),
+ ICSSG_STATS(rx_class12_hits),
+ ICSSG_STATS(rx_class13_hits),
+ ICSSG_STATS(rx_class14_hits),
+ ICSSG_STATS(rx_class15_hits),
+ ICSSG_STATS(rx_smd_frags),
+ ICSSG_STATS(rx_bucket1_size),
+ ICSSG_STATS(rx_bucket2_size),
+ ICSSG_STATS(rx_bucket3_size),
+ ICSSG_STATS(rx_bucket4_size),
+ ICSSG_STATS(rx_64B_frames),
+ ICSSG_STATS(rx_bucket1_frames),
+ ICSSG_STATS(rx_bucket2_frames),
+ ICSSG_STATS(rx_bucket3_frames),
+ ICSSG_STATS(rx_bucket4_frames),
+ ICSSG_STATS(rx_bucket5_frames),
+ ICSSG_STATS(rx_total_bytes),
+ ICSSG_STATS(rx_tx_total_bytes),
+ /* Tx */
+ ICSSG_STATS(tx_good_frames),
+ ICSSG_STATS(tx_broadcast_frames),
+ ICSSG_STATS(tx_multicast_frames),
+ ICSSG_STATS(tx_odd_nibble_frames),
+ ICSSG_STATS(tx_underflow_errors),
+ ICSSG_STATS(tx_frame_max_size),
+ ICSSG_STATS(tx_max_size_error_frames),
+ ICSSG_STATS(tx_frame_min_size),
+ ICSSG_STATS(tx_min_size_error_frames),
+ ICSSG_STATS(tx_bucket1_size),
+ ICSSG_STATS(tx_bucket2_size),
+ ICSSG_STATS(tx_bucket3_size),
+ ICSSG_STATS(tx_bucket4_size),
+ ICSSG_STATS(tx_64B_frames),
+ ICSSG_STATS(tx_bucket1_frames),
+ ICSSG_STATS(tx_bucket2_frames),
+ ICSSG_STATS(tx_bucket3_frames),
+ ICSSG_STATS(tx_bucket4_frames),
+ ICSSG_STATS(tx_bucket5_frames),
+ ICSSG_STATS(tx_total_bytes),
+};
+
+static void emac_get_drvinfo(struct net_device *ndev,
+ struct ethtool_drvinfo *info)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ struct prueth *prueth = emac->prueth;
+
+ strscpy(info->driver, dev_driver_string(prueth->dev),
+ sizeof(info->driver));
+ strscpy(info->bus_info, dev_name(prueth->dev), sizeof(info->bus_info));
+}
+
+static u32 emac_get_msglevel(struct net_device *ndev)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ return emac->msg_enable;
+}
+
+static void emac_set_msglevel(struct net_device *ndev, u32 value)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ emac->msg_enable = value;
+}
+
+static int emac_get_link_ksettings(struct net_device *ndev,
+ struct ethtool_link_ksettings *ecmd)
+{
+ return phy_ethtool_get_link_ksettings(ndev, ecmd);
+}
+
+static int emac_set_link_ksettings(struct net_device *ndev,
+ const struct ethtool_link_ksettings *ecmd)
+{
+ return phy_ethtool_set_link_ksettings(ndev, ecmd);
+}
+
+static int emac_get_eee(struct net_device *ndev, struct ethtool_eee *edata)
+{
+ if (!ndev->phydev)
+ return -EOPNOTSUPP;
+
+ return phy_ethtool_get_eee(ndev->phydev, edata);
+}
+
+static int emac_set_eee(struct net_device *ndev, struct ethtool_eee *edata)
+{
+ if (!ndev->phydev)
+ return -EOPNOTSUPP;
+
+ return phy_ethtool_set_eee(ndev->phydev, edata);
+}
+
+static int emac_nway_reset(struct net_device *ndev)
+{
+ return phy_ethtool_nway_reset(ndev);
+}
+
+#define EMAC_PRIV_IET_FRAME_PREEMPTION BIT(0)
+#define EMAC_PRIV_IET_MAC_VERIFY BIT(1)
+
+static const char emac_ethtool_priv_flags[][ETH_GSTRING_LEN] = {
+ "iet-frame-preemption",
+ "iet-mac-verify",
+};
+
+static int emac_get_sset_count(struct net_device *ndev, int stringset)
+{
+ switch (stringset) {
+ case ETH_SS_STATS:
+ return ARRAY_SIZE(icssg_ethtool_stats);
+ case ETH_SS_PRIV_FLAGS:
+ return ARRAY_SIZE(emac_ethtool_priv_flags);
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void emac_get_strings(struct net_device *ndev, u32 stringset, u8 *data)
+{
+ u8 *p = data;
+ int i;
+
+ switch (stringset) {
+ case ETH_SS_STATS:
+ for (i = 0; i < ARRAY_SIZE(icssg_ethtool_stats); i++) {
+ memcpy(p, icssg_ethtool_stats[i].name,
+ ETH_GSTRING_LEN);
+ p += ETH_GSTRING_LEN;
+ }
+ break;
+ case ETH_SS_PRIV_FLAGS:
+ for (i = 0; i < ARRAY_SIZE(emac_ethtool_priv_flags); i++) {
+ memcpy(p, emac_ethtool_priv_flags[i],
+ ETH_GSTRING_LEN);
+ p += ETH_GSTRING_LEN;
+ }
+ break;
+ default:
+ break;
+ }
+}
+
+static void emac_get_ethtool_stats(struct net_device *ndev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+ u32 base = stats_base[slice];
+ u32 val;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(icssg_ethtool_stats); i++) {
+ regmap_read(prueth->miig_rt,
+ base + icssg_ethtool_stats[i].offset,
+ &val);
+ data[i] = val;
+ }
+}
+
+static int emac_set_channels(struct net_device *ndev,
+ struct ethtool_channels *ch)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ /* Check if interface is up. Can change the num queues when
+ * the interface is down.
+ */
+ if (netif_running(emac->ndev))
+ return -EBUSY;
+
+ emac->tx_ch_num = ch->tx_count;
+
+ return 0;
+}
+
+static void emac_get_channels(struct net_device *ndev,
+ struct ethtool_channels *ch)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ ch->max_rx = 1;
+ ch->max_tx = PRUETH_MAX_TX_QUEUES;
+ ch->rx_count = 1;
+ ch->tx_count = emac->tx_ch_num;
+}
+
+const struct ethtool_ops icssg_ethtool_ops = {
+ .get_drvinfo = emac_get_drvinfo,
+ .get_msglevel = emac_get_msglevel,
+ .set_msglevel = emac_set_msglevel,
+ .get_sset_count = emac_get_sset_count,
+ .get_ethtool_stats = emac_get_ethtool_stats,
+ .get_strings = emac_get_strings,
+ .get_channels = emac_get_channels,
+ .set_channels = emac_set_channels,
+ .get_link_ksettings = emac_get_link_ksettings,
+ .set_link_ksettings = emac_set_link_ksettings,
+ .get_link = ethtool_op_get_link,
+ .get_eee = emac_get_eee,
+ .set_eee = emac_set_eee,
+ .nway_reset = emac_nway_reset,
+};
new file mode 100644
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Texas Instruments ICSSG Ethernet Driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include <linux/etherdevice.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+#include "icssg_mii_rt.h"
+#include "icssg_prueth.h"
+
+void icssg_mii_update_ipg(struct regmap *mii_rt, int mii, u32 ipg)
+{
+ u32 val;
+
+ if (mii == ICSS_MII0) {
+ regmap_write(mii_rt, PRUSS_MII_RT_TX_IPG0, ipg);
+ } else {
+ regmap_read(mii_rt, PRUSS_MII_RT_TX_IPG0, &val);
+ regmap_write(mii_rt, PRUSS_MII_RT_TX_IPG1, ipg);
+ regmap_write(mii_rt, PRUSS_MII_RT_TX_IPG0, val);
+ }
+}
+
+void icssg_mii_update_mtu(struct regmap *mii_rt, int mii, int mtu)
+{
+ mtu += (ETH_HLEN + ETH_FCS_LEN);
+ if (mii == ICSS_MII0) {
+ regmap_update_bits(mii_rt,
+ PRUSS_MII_RT_RX_FRMS0,
+ PRUSS_MII_RT_RX_FRMS_MAX_FRM_MASK,
+ (mtu - 1) << PRUSS_MII_RT_RX_FRMS_MAX_FRM_SHIFT);
+ } else {
+ regmap_update_bits(mii_rt,
+ PRUSS_MII_RT_RX_FRMS1,
+ PRUSS_MII_RT_RX_FRMS_MAX_FRM_MASK,
+ (mtu - 1) << PRUSS_MII_RT_RX_FRMS_MAX_FRM_SHIFT);
+ }
+}
+
+void icssg_update_rgmii_cfg(struct regmap *miig_rt, struct prueth_emac *emac)
+{
+ u32 gig_en_mask, gig_val = 0, full_duplex_mask, full_duplex_val = 0;
+ int slice = prueth_emac_slice(emac);
+ u32 inband_en_mask, inband_val = 0;
+
+ gig_en_mask = (slice == ICSS_MII0) ? RGMII_CFG_GIG_EN_MII0 :
+ RGMII_CFG_GIG_EN_MII1;
+ if (emac->speed == SPEED_1000)
+ gig_val = gig_en_mask;
+ regmap_update_bits(miig_rt, RGMII_CFG_OFFSET, gig_en_mask, gig_val);
+
+ inband_en_mask = (slice == ICSS_MII0) ? RGMII_CFG_INBAND_EN_MII0 :
+ RGMII_CFG_INBAND_EN_MII1;
+ if (emac->speed == SPEED_10 && phy_interface_mode_is_rgmii(emac->phy_if))
+ inband_val = inband_en_mask;
+ regmap_update_bits(miig_rt, RGMII_CFG_OFFSET, inband_en_mask, inband_val);
+
+ full_duplex_mask = (slice == ICSS_MII0) ? RGMII_CFG_FULL_DUPLEX_MII0 :
+ RGMII_CFG_FULL_DUPLEX_MII1;
+ if (emac->duplex == DUPLEX_FULL)
+ full_duplex_val = full_duplex_mask;
+ regmap_update_bits(miig_rt, RGMII_CFG_OFFSET, full_duplex_mask,
+ full_duplex_val);
+}
+
+void icssg_miig_set_interface_mode(struct regmap *miig_rt, int mii, phy_interface_t phy_if)
+{
+ u32 val, mask, shift;
+
+ mask = mii == ICSS_MII0 ? ICSSG_CFG_MII0_MODE : ICSSG_CFG_MII1_MODE;
+ shift = mii == ICSS_MII0 ? ICSSG_CFG_MII0_MODE_SHIFT : ICSSG_CFG_MII1_MODE_SHIFT;
+
+ val = MII_MODE_RGMII;
+ if (phy_if == PHY_INTERFACE_MODE_MII)
+ val = MII_MODE_MII;
+
+ val <<= shift;
+ regmap_update_bits(miig_rt, ICSSG_CFG_OFFSET, mask, val);
+ regmap_read(miig_rt, ICSSG_CFG_OFFSET, &val);
+}
+
+u32 icssg_rgmii_cfg_get_bitfield(struct regmap *miig_rt, u32 mask, u32 shift)
+{
+ u32 val;
+
+ regmap_read(miig_rt, RGMII_CFG_OFFSET, &val);
+ val &= mask;
+ val >>= shift;
+
+ return val;
+}
+
+u32 icssg_rgmii_get_speed(struct regmap *miig_rt, int mii)
+{
+ u32 shift = RGMII_CFG_SPEED_MII0_SHIFT, mask = RGMII_CFG_SPEED_MII0;
+
+ if (mii == ICSS_MII1) {
+ shift = RGMII_CFG_SPEED_MII1_SHIFT;
+ mask = RGMII_CFG_SPEED_MII1;
+ }
+
+ return icssg_rgmii_cfg_get_bitfield(miig_rt, mask, shift);
+}
+
+u32 icssg_rgmii_get_fullduplex(struct regmap *miig_rt, int mii)
+{
+ u32 shift = RGMII_CFG_FULLDUPLEX_MII0_SHIFT;
+ u32 mask = RGMII_CFG_FULLDUPLEX_MII0;
+
+ if (mii == ICSS_MII1) {
+ shift = RGMII_CFG_FULLDUPLEX_MII1_SHIFT;
+ mask = RGMII_CFG_FULLDUPLEX_MII1;
+ }
+
+ return icssg_rgmii_cfg_get_bitfield(miig_rt, mask, shift);
+}
new file mode 100644
@@ -0,0 +1,151 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+/* PRU-ICSS MII_RT register definitions
+ *
+ * Copyright (C) 2015-2022 Texas Instruments Incorporated - https://www.ti.com
+ */
+
+#ifndef __NET_PRUSS_MII_RT_H__
+#define __NET_PRUSS_MII_RT_H__
+
+#include <linux/if_ether.h>
+#include <linux/phy.h>
+
+/* PRUSS_MII_RT Registers */
+#define PRUSS_MII_RT_RXCFG0 0x0
+#define PRUSS_MII_RT_RXCFG1 0x4
+#define PRUSS_MII_RT_TXCFG0 0x10
+#define PRUSS_MII_RT_TXCFG1 0x14
+#define PRUSS_MII_RT_TX_CRC0 0x20
+#define PRUSS_MII_RT_TX_CRC1 0x24
+#define PRUSS_MII_RT_TX_IPG0 0x30
+#define PRUSS_MII_RT_TX_IPG1 0x34
+#define PRUSS_MII_RT_PRS0 0x38
+#define PRUSS_MII_RT_PRS1 0x3c
+#define PRUSS_MII_RT_RX_FRMS0 0x40
+#define PRUSS_MII_RT_RX_FRMS1 0x44
+#define PRUSS_MII_RT_RX_PCNT0 0x48
+#define PRUSS_MII_RT_RX_PCNT1 0x4c
+#define PRUSS_MII_RT_RX_ERR0 0x50
+#define PRUSS_MII_RT_RX_ERR1 0x54
+
+/* PRUSS_MII_RT_RXCFG0/1 bits */
+#define PRUSS_MII_RT_RXCFG_RX_ENABLE BIT(0)
+#define PRUSS_MII_RT_RXCFG_RX_DATA_RDY_MODE_DIS BIT(1)
+#define PRUSS_MII_RT_RXCFG_RX_CUT_PREAMBLE BIT(2)
+#define PRUSS_MII_RT_RXCFG_RX_MUX_SEL BIT(3)
+#define PRUSS_MII_RT_RXCFG_RX_L2_EN BIT(4)
+#define PRUSS_MII_RT_RXCFG_RX_BYTE_SWAP BIT(5)
+#define PRUSS_MII_RT_RXCFG_RX_AUTO_FWD_PRE BIT(6)
+#define PRUSS_MII_RT_RXCFG_RX_L2_EOF_SCLR_DIS BIT(9)
+
+/* PRUSS_MII_RT_TXCFG0/1 bits */
+#define PRUSS_MII_RT_TXCFG_TX_ENABLE BIT(0)
+#define PRUSS_MII_RT_TXCFG_TX_AUTO_PREAMBLE BIT(1)
+#define PRUSS_MII_RT_TXCFG_TX_EN_MODE BIT(2)
+#define PRUSS_MII_RT_TXCFG_TX_BYTE_SWAP BIT(3)
+#define PRUSS_MII_RT_TXCFG_TX_MUX_SEL BIT(8)
+#define PRUSS_MII_RT_TXCFG_PRE_TX_AUTO_SEQUENCE BIT(9)
+#define PRUSS_MII_RT_TXCFG_PRE_TX_AUTO_ESC_ERR BIT(10)
+#define PRUSS_MII_RT_TXCFG_TX_32_MODE_EN BIT(11)
+#define PRUSS_MII_RT_TXCFG_TX_IPG_WIRE_CLK_EN BIT(12) /* SR2.0 onwards */
+
+#define PRUSS_MII_RT_TXCFG_TX_START_DELAY_SHIFT 16
+#define PRUSS_MII_RT_TXCFG_TX_START_DELAY_MASK GENMASK(25, 16)
+
+#define PRUSS_MII_RT_TXCFG_TX_CLK_DELAY_SHIFT 28
+#define PRUSS_MII_RT_TXCFG_TX_CLK_DELAY_MASK GENMASK(30, 28)
+
+/* PRUSS_MII_RT_TX_IPG0/1 bits */
+#define PRUSS_MII_RT_TX_IPG_IPG_SHIFT 0
+#define PRUSS_MII_RT_TX_IPG_IPG_MASK GENMASK(9, 0)
+
+/* PRUSS_MII_RT_PRS0/1 bits */
+#define PRUSS_MII_RT_PRS_COL BIT(0)
+#define PRUSS_MII_RT_PRS_CRS BIT(1)
+
+/* PRUSS_MII_RT_RX_FRMS0/1 bits */
+#define PRUSS_MII_RT_RX_FRMS_MIN_FRM_SHIFT 0
+#define PRUSS_MII_RT_RX_FRMS_MIN_FRM_MASK GENMASK(15, 0)
+
+#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_SHIFT 16
+#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_MASK GENMASK(31, 16)
+
+/* Min/Max in MII_RT_RX_FRMS */
+/* For EMAC and Switch */
+#define PRUSS_MII_RT_RX_FRMS_MAX (VLAN_ETH_FRAME_LEN + ETH_FCS_LEN)
+#define PRUSS_MII_RT_RX_FRMS_MIN_FRM (64)
+
+/* for HSR and PRP */
+#define PRUSS_MII_RT_RX_FRMS_MAX_FRM_LRE (PRUSS_MII_RT_RX_FRMS_MAX + \
+ ICSS_LRE_TAG_RCT_SIZE)
+/* PRUSS_MII_RT_RX_PCNT0/1 bits */
+#define PRUSS_MII_RT_RX_PCNT_MIN_PCNT_SHIFT 0
+#define PRUSS_MII_RT_RX_PCNT_MIN_PCNT_MASK GENMASK(3, 0)
+
+#define PRUSS_MII_RT_RX_PCNT_MAX_PCNT_SHIFT 4
+#define PRUSS_MII_RT_RX_PCNT_MAX_PCNT_MASK GENMASK(7, 4)
+
+/* PRUSS_MII_RT_RX_ERR0/1 bits */
+#define PRUSS_MII_RT_RX_ERR_MIN_PCNT_ERR BIT(0)
+#define PRUSS_MII_RT_RX_ERR_MAX_PCNT_ERR BIT(1)
+#define PRUSS_MII_RT_RX_ERR_MIN_FRM_ERR BIT(2)
+#define PRUSS_MII_RT_RX_ERR_MAX_FRM_ERR BIT(3)
+
+#define ICSSG_CFG_OFFSET 0
+#define RGMII_CFG_OFFSET 4
+
+/* Constant to choose between MII0 and MII1 */
+#define ICSS_MII0 0
+#define ICSS_MII1 1
+
+/* ICSSG_CFG Register bits */
+#define ICSSG_CFG_SGMII_MODE BIT(16)
+#define ICSSG_CFG_TX_PRU_EN BIT(11)
+#define ICSSG_CFG_RX_SFD_TX_SOF_EN BIT(10)
+#define ICSSG_CFG_RTU_PRU_PSI_SHARE_EN BIT(9)
+#define ICSSG_CFG_IEP1_TX_EN BIT(8)
+#define ICSSG_CFG_MII1_MODE GENMASK(6, 5)
+#define ICSSG_CFG_MII1_MODE_SHIFT 5
+#define ICSSG_CFG_MII0_MODE GENMASK(4, 3)
+#define ICSSG_CFG_MII0_MODE_SHIFT 3
+#define ICSSG_CFG_RX_L2_G_EN BIT(2)
+#define ICSSG_CFG_TX_L2_EN BIT(1)
+#define ICSSG_CFG_TX_L1_EN BIT(0)
+
+enum mii_mode {
+ MII_MODE_MII = 0,
+ MII_MODE_RGMII
+};
+
+/* RGMII CFG Register bits */
+#define RGMII_CFG_INBAND_EN_MII0 BIT(16)
+#define RGMII_CFG_GIG_EN_MII0 BIT(17)
+#define RGMII_CFG_INBAND_EN_MII1 BIT(20)
+#define RGMII_CFG_GIG_EN_MII1 BIT(21)
+#define RGMII_CFG_FULL_DUPLEX_MII0 BIT(18)
+#define RGMII_CFG_FULL_DUPLEX_MII1 BIT(22)
+#define RGMII_CFG_SPEED_MII0 GENMASK(2, 1)
+#define RGMII_CFG_SPEED_MII1 GENMASK(6, 5)
+#define RGMII_CFG_SPEED_MII0_SHIFT 1
+#define RGMII_CFG_SPEED_MII1_SHIFT 5
+#define RGMII_CFG_FULLDUPLEX_MII0 BIT(3)
+#define RGMII_CFG_FULLDUPLEX_MII1 BIT(7)
+#define RGMII_CFG_FULLDUPLEX_MII0_SHIFT 3
+#define RGMII_CFG_FULLDUPLEX_MII1_SHIFT 7
+#define RGMII_CFG_SPEED_10M 0
+#define RGMII_CFG_SPEED_100M 1
+#define RGMII_CFG_SPEED_1G 2
+
+struct regmap;
+struct prueth_emac;
+
+void icssg_mii_update_ipg(struct regmap *mii_rt, int mii, u32 ipg);
+void icssg_mii_update_mtu(struct regmap *mii_rt, int mii, int mtu);
+void icssg_update_rgmii_cfg(struct regmap *miig_rt, struct prueth_emac *emac);
+u32 icssg_rgmii_cfg_get_bitfield(struct regmap *miig_rt, u32 mask, u32 shift);
+u32 icssg_rgmii_get_speed(struct regmap *miig_rt, int mii);
+u32 icssg_rgmii_get_fullduplex(struct regmap *miig_rt, int mii);
+void icssg_miig_set_interface_mode(struct regmap *miig_rt, int mii, phy_interface_t phy_if);
+
+#endif /* __NET_PRUSS_MII_RT_H__ */
new file mode 100644
@@ -0,0 +1,1886 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* Texas Instruments ICSSG Ethernet Driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/dma-mapping.h>
+#include <linux/dma/ti-cppi5.h>
+#include <linux/etherdevice.h>
+#include <linux/genalloc.h>
+#include <linux/if_vlan.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/remoteproc/pruss.h>
+#include <linux/regmap.h>
+#include <linux/remoteproc.h>
+
+#include "icssg_prueth.h"
+#include "icssg_mii_rt.h"
+#include "k3-cppi-desc-pool.h"
+
+#define PRUETH_MODULE_DESCRIPTION "PRUSS ICSSG Ethernet driver"
+
+#define PRUETH_MAX_MTU (2000 - ETH_HLEN - ETH_FCS_LEN)
+#define PRUETH_MIN_PKT_SIZE (VLAN_ETH_ZLEN)
+#define PRUETH_MAX_PKT_SIZE (PRUETH_MAX_MTU + ETH_HLEN + ETH_FCS_LEN)
+
+/* Netif debug messages possible */
+#define PRUETH_EMAC_DEBUG (NETIF_MSG_DRV | \
+ NETIF_MSG_PROBE | \
+ NETIF_MSG_LINK | \
+ NETIF_MSG_TIMER | \
+ NETIF_MSG_IFDOWN | \
+ NETIF_MSG_IFUP | \
+ NETIF_MSG_RX_ERR | \
+ NETIF_MSG_TX_ERR | \
+ NETIF_MSG_TX_QUEUED | \
+ NETIF_MSG_INTR | \
+ NETIF_MSG_TX_DONE | \
+ NETIF_MSG_RX_STATUS | \
+ NETIF_MSG_PKTDATA | \
+ NETIF_MSG_HW | \
+ NETIF_MSG_WOL)
+
+#define prueth_napi_to_emac(napi) container_of(napi, struct prueth_emac, napi_rx)
+
+/* CTRLMMR_ICSSG_RGMII_CTRL register bits */
+#define ICSSG_CTRL_RGMII_ID_MODE BIT(24)
+
+static void prueth_cleanup_rx_chns(struct prueth_emac *emac,
+ struct prueth_rx_chn *rx_chn,
+ int max_rflows)
+{
+ if (rx_chn->desc_pool)
+ k3_cppi_desc_pool_destroy(rx_chn->desc_pool);
+
+ if (rx_chn->rx_chn)
+ k3_udma_glue_release_rx_chn(rx_chn->rx_chn);
+}
+
+static void prueth_cleanup_tx_chns(struct prueth_emac *emac)
+{
+ int i;
+
+ for (i = 0; i < emac->tx_ch_num; i++) {
+ struct prueth_tx_chn *tx_chn = &emac->tx_chns[i];
+
+ if (tx_chn->desc_pool)
+ k3_cppi_desc_pool_destroy(tx_chn->desc_pool);
+
+ if (tx_chn->tx_chn)
+ k3_udma_glue_release_tx_chn(tx_chn->tx_chn);
+
+ /* Assume prueth_cleanup_tx_chns() is called at the
+ * end after all channel resources are freed
+ */
+ memset(tx_chn, 0, sizeof(*tx_chn));
+ }
+}
+
+static void prueth_ndev_del_tx_napi(struct prueth_emac *emac, int num)
+{
+ int i;
+
+ for (i = 0; i < num; i++) {
+ struct prueth_tx_chn *tx_chn = &emac->tx_chns[i];
+
+ if (tx_chn->irq)
+ free_irq(tx_chn->irq, tx_chn);
+ netif_napi_del(&tx_chn->napi_tx);
+ }
+}
+
+static void prueth_xmit_free(struct prueth_tx_chn *tx_chn,
+ struct cppi5_host_desc_t *desc)
+{
+ struct cppi5_host_desc_t *first_desc, *next_desc;
+ dma_addr_t buf_dma, next_desc_dma;
+ u32 buf_dma_len;
+
+ first_desc = desc;
+ next_desc = first_desc;
+
+ cppi5_hdesc_get_obuf(first_desc, &buf_dma, &buf_dma_len);
+ k3_udma_glue_tx_cppi5_to_dma_addr(tx_chn->tx_chn, &buf_dma);
+
+ dma_unmap_single(tx_chn->dma_dev, buf_dma, buf_dma_len,
+ DMA_TO_DEVICE);
+
+ next_desc_dma = cppi5_hdesc_get_next_hbdesc(first_desc);
+ k3_udma_glue_tx_cppi5_to_dma_addr(tx_chn->tx_chn, &next_desc_dma);
+ while (next_desc_dma) {
+ next_desc = k3_cppi_desc_pool_dma2virt(tx_chn->desc_pool,
+ next_desc_dma);
+ cppi5_hdesc_get_obuf(next_desc, &buf_dma, &buf_dma_len);
+ k3_udma_glue_tx_cppi5_to_dma_addr(tx_chn->tx_chn, &buf_dma);
+
+ dma_unmap_page(tx_chn->dma_dev, buf_dma, buf_dma_len,
+ DMA_TO_DEVICE);
+
+ next_desc_dma = cppi5_hdesc_get_next_hbdesc(next_desc);
+ k3_udma_glue_tx_cppi5_to_dma_addr(tx_chn->tx_chn, &next_desc_dma);
+
+ k3_cppi_desc_pool_free(tx_chn->desc_pool, next_desc);
+ }
+
+ k3_cppi_desc_pool_free(tx_chn->desc_pool, first_desc);
+}
+
+static int emac_tx_complete_packets(struct prueth_emac *emac, int chn,
+ int budget)
+{
+ struct net_device *ndev = emac->ndev;
+ struct cppi5_host_desc_t *desc_tx;
+ struct netdev_queue *netif_txq;
+ struct prueth_tx_chn *tx_chn;
+ unsigned int total_bytes = 0;
+ struct sk_buff *skb;
+ dma_addr_t desc_dma;
+ int res, num_tx = 0;
+ void **swdata;
+
+ tx_chn = &emac->tx_chns[chn];
+
+ while (budget) {
+ res = k3_udma_glue_pop_tx_chn(tx_chn->tx_chn, &desc_dma);
+ if (res == -ENODATA)
+ break;
+
+ /* teardown completion */
+ if (cppi5_desc_is_tdcm(desc_dma)) {
+ if (atomic_dec_and_test(&emac->tdown_cnt))
+ complete(&emac->tdown_complete);
+ break;
+ }
+
+ desc_tx = k3_cppi_desc_pool_dma2virt(tx_chn->desc_pool,
+ desc_dma);
+ swdata = cppi5_hdesc_get_swdata(desc_tx);
+
+ skb = *(swdata);
+ prueth_xmit_free(tx_chn, desc_tx);
+
+ ndev = skb->dev;
+ ndev->stats.tx_packets++;
+ ndev->stats.tx_bytes += skb->len;
+ total_bytes += skb->len;
+ napi_consume_skb(skb, budget);
+ num_tx++;
+ budget--;
+ }
+
+ if (!num_tx)
+ return 0;
+
+ netif_txq = netdev_get_tx_queue(ndev, chn);
+ netdev_tx_completed_queue(netif_txq, num_tx, total_bytes);
+
+ if (netif_tx_queue_stopped(netif_txq)) {
+ /* If the TX queue was stopped, wake it now
+ * if we have enough room.
+ */
+ __netif_tx_lock(netif_txq, smp_processor_id());
+ if (netif_running(ndev) &&
+ (k3_cppi_desc_pool_avail(tx_chn->desc_pool) >=
+ MAX_SKB_FRAGS))
+ netif_tx_wake_queue(netif_txq);
+ __netif_tx_unlock(netif_txq);
+ }
+
+ return num_tx;
+}
+
+static int emac_napi_tx_poll(struct napi_struct *napi_tx, int budget)
+{
+ struct prueth_tx_chn *tx_chn = prueth_napi_to_tx_chn(napi_tx);
+ struct prueth_emac *emac = tx_chn->emac;
+ int num_tx_packets;
+
+ num_tx_packets = emac_tx_complete_packets(emac, tx_chn->id, budget);
+
+ if (num_tx_packets < budget) {
+ napi_complete(napi_tx);
+ enable_irq(tx_chn->irq);
+ }
+
+ return num_tx_packets;
+}
+
+static irqreturn_t prueth_tx_irq(int irq, void *dev_id)
+{
+ struct prueth_tx_chn *tx_chn = dev_id;
+
+ disable_irq_nosync(irq);
+ napi_schedule(&tx_chn->napi_tx);
+
+ return IRQ_HANDLED;
+}
+
+static int prueth_ndev_add_tx_napi(struct prueth_emac *emac)
+{
+ struct prueth *prueth = emac->prueth;
+ int i, ret;
+
+ for (i = 0; i < emac->tx_ch_num; i++) {
+ struct prueth_tx_chn *tx_chn = &emac->tx_chns[i];
+
+ netif_napi_add_tx_weight(emac->ndev, &tx_chn->napi_tx,
+ emac_napi_tx_poll, NAPI_POLL_WEIGHT);
+ ret = request_irq(tx_chn->irq, prueth_tx_irq,
+ IRQF_TRIGGER_HIGH, tx_chn->name,
+ tx_chn);
+ if (ret) {
+ netif_napi_del(&tx_chn->napi_tx);
+ dev_err(prueth->dev, "unable to request TX IRQ %d\n",
+ tx_chn->irq);
+ goto fail;
+ }
+ }
+
+ return 0;
+fail:
+ prueth_ndev_del_tx_napi(emac, i);
+ return ret;
+}
+
+static int prueth_init_tx_chns(struct prueth_emac *emac)
+{
+ static const struct k3_ring_cfg ring_cfg = {
+ .elm_size = K3_RINGACC_RING_ELSIZE_8,
+ .mode = K3_RINGACC_RING_MODE_RING,
+ .flags = 0,
+ .size = PRUETH_MAX_TX_DESC,
+ };
+ struct k3_udma_glue_tx_channel_cfg tx_cfg;
+ struct device *dev = emac->prueth->dev;
+ struct net_device *ndev = emac->ndev;
+ int ret, slice, i;
+ u32 hdesc_size;
+
+ slice = prueth_emac_slice(emac);
+ if (slice < 0)
+ return slice;
+
+ init_completion(&emac->tdown_complete);
+
+ hdesc_size = cppi5_hdesc_calc_size(true, PRUETH_NAV_PS_DATA_SIZE,
+ PRUETH_NAV_SW_DATA_SIZE);
+ memset(&tx_cfg, 0, sizeof(tx_cfg));
+ tx_cfg.swdata_size = PRUETH_NAV_SW_DATA_SIZE;
+ tx_cfg.tx_cfg = ring_cfg;
+ tx_cfg.txcq_cfg = ring_cfg;
+
+ for (i = 0; i < emac->tx_ch_num; i++) {
+ struct prueth_tx_chn *tx_chn = &emac->tx_chns[i];
+
+ /* To differentiate channels for SLICE0 vs SLICE1 */
+ snprintf(tx_chn->name, sizeof(tx_chn->name),
+ "tx%d-%d", slice, i);
+
+ tx_chn->emac = emac;
+ tx_chn->id = i;
+ tx_chn->descs_num = PRUETH_MAX_TX_DESC;
+
+ tx_chn->tx_chn =
+ k3_udma_glue_request_tx_chn(dev, tx_chn->name,
+ &tx_cfg);
+ if (IS_ERR(tx_chn->tx_chn)) {
+ ret = PTR_ERR(tx_chn->tx_chn);
+ tx_chn->tx_chn = NULL;
+ netdev_err(ndev,
+ "Failed to request tx dma ch: %d\n", ret);
+ goto fail;
+ }
+
+ tx_chn->dma_dev = k3_udma_glue_tx_get_dma_device(tx_chn->tx_chn);
+ tx_chn->desc_pool =
+ k3_cppi_desc_pool_create_name(tx_chn->dma_dev,
+ tx_chn->descs_num,
+ hdesc_size,
+ tx_chn->name);
+ if (IS_ERR(tx_chn->desc_pool)) {
+ ret = PTR_ERR(tx_chn->desc_pool);
+ tx_chn->desc_pool = NULL;
+ netdev_err(ndev, "Failed to create tx pool: %d\n", ret);
+ goto fail;
+ }
+
+ tx_chn->irq = k3_udma_glue_tx_get_irq(tx_chn->tx_chn);
+ if (tx_chn->irq <= 0) {
+ ret = -EINVAL;
+ netdev_err(ndev, "failed to get tx irq\n");
+ goto fail;
+ }
+
+ snprintf(tx_chn->name, sizeof(tx_chn->name), "%s-tx%d",
+ dev_name(dev), tx_chn->id);
+ }
+
+ return 0;
+
+fail:
+ prueth_cleanup_tx_chns(emac);
+ return ret;
+}
+
+static int prueth_init_rx_chns(struct prueth_emac *emac,
+ struct prueth_rx_chn *rx_chn,
+ char *name, u32 max_rflows,
+ u32 max_desc_num)
+{
+ struct k3_udma_glue_rx_channel_cfg rx_cfg;
+ struct device *dev = emac->prueth->dev;
+ struct net_device *ndev = emac->ndev;
+ u32 fdqring_id, hdesc_size;
+ int i, ret = 0, slice;
+
+ slice = prueth_emac_slice(emac);
+ if (slice < 0)
+ return slice;
+
+ /* To differentiate channels for SLICE0 vs SLICE1 */
+ snprintf(rx_chn->name, sizeof(rx_chn->name), "%s%d", name, slice);
+
+ hdesc_size = cppi5_hdesc_calc_size(true, PRUETH_NAV_PS_DATA_SIZE,
+ PRUETH_NAV_SW_DATA_SIZE);
+ memset(&rx_cfg, 0, sizeof(rx_cfg));
+ rx_cfg.swdata_size = PRUETH_NAV_SW_DATA_SIZE;
+ rx_cfg.flow_id_num = max_rflows;
+ rx_cfg.flow_id_base = -1; /* udmax will auto select flow id base */
+
+ /* init all flows */
+ rx_chn->dev = dev;
+ rx_chn->descs_num = max_desc_num;
+
+ rx_chn->rx_chn = k3_udma_glue_request_rx_chn(dev, rx_chn->name,
+ &rx_cfg);
+ if (IS_ERR(rx_chn->rx_chn)) {
+ ret = PTR_ERR(rx_chn->rx_chn);
+ rx_chn->rx_chn = NULL;
+ netdev_err(ndev, "Failed to request rx dma ch: %d\n", ret);
+ goto fail;
+ }
+
+ rx_chn->dma_dev = k3_udma_glue_rx_get_dma_device(rx_chn->rx_chn);
+ rx_chn->desc_pool = k3_cppi_desc_pool_create_name(rx_chn->dma_dev,
+ rx_chn->descs_num,
+ hdesc_size,
+ rx_chn->name);
+ if (IS_ERR(rx_chn->desc_pool)) {
+ ret = PTR_ERR(rx_chn->desc_pool);
+ rx_chn->desc_pool = NULL;
+ netdev_err(ndev, "Failed to create rx pool: %d\n", ret);
+ goto fail;
+ }
+
+ emac->rx_flow_id_base = k3_udma_glue_rx_get_flow_id_base(rx_chn->rx_chn);
+ netdev_dbg(ndev, "flow id base = %d\n", emac->rx_flow_id_base);
+
+ fdqring_id = K3_RINGACC_RING_ID_ANY;
+ for (i = 0; i < rx_cfg.flow_id_num; i++) {
+ struct k3_ring_cfg rxring_cfg = {
+ .elm_size = K3_RINGACC_RING_ELSIZE_8,
+ .mode = K3_RINGACC_RING_MODE_RING,
+ .flags = 0,
+ };
+ struct k3_ring_cfg fdqring_cfg = {
+ .elm_size = K3_RINGACC_RING_ELSIZE_8,
+ .flags = K3_RINGACC_RING_SHARED,
+ };
+ struct k3_udma_glue_rx_flow_cfg rx_flow_cfg = {
+ .rx_cfg = rxring_cfg,
+ .rxfdq_cfg = fdqring_cfg,
+ .ring_rxq_id = K3_RINGACC_RING_ID_ANY,
+ .src_tag_lo_sel =
+ K3_UDMA_GLUE_SRC_TAG_LO_USE_REMOTE_SRC_TAG,
+ };
+
+ rx_flow_cfg.ring_rxfdq0_id = fdqring_id;
+ rx_flow_cfg.rx_cfg.size = max_desc_num;
+ rx_flow_cfg.rxfdq_cfg.size = max_desc_num;
+ rx_flow_cfg.rxfdq_cfg.mode = emac->prueth->pdata.fdqring_mode;
+
+ ret = k3_udma_glue_rx_flow_init(rx_chn->rx_chn,
+ i, &rx_flow_cfg);
+ if (ret) {
+ netdev_err(ndev, "Failed to init rx flow%d %d\n",
+ i, ret);
+ goto fail;
+ }
+ if (!i)
+ fdqring_id = k3_udma_glue_rx_flow_get_fdq_id(rx_chn->rx_chn,
+ i);
+ rx_chn->irq[i] = k3_udma_glue_rx_get_irq(rx_chn->rx_chn, i);
+ if (rx_chn->irq[i] <= 0) {
+ ret = rx_chn->irq[i];
+ netdev_err(ndev, "Failed to get rx dma irq");
+ goto fail;
+ }
+ }
+
+ return 0;
+
+fail:
+ prueth_cleanup_rx_chns(emac, rx_chn, max_rflows);
+ return ret;
+}
+
+static int prueth_dma_rx_push(struct prueth_emac *emac,
+ struct sk_buff *skb,
+ struct prueth_rx_chn *rx_chn)
+{
+ struct net_device *ndev = emac->ndev;
+ struct cppi5_host_desc_t *desc_rx;
+ u32 pkt_len = skb_tailroom(skb);
+ dma_addr_t desc_dma;
+ dma_addr_t buf_dma;
+ void **swdata;
+
+ desc_rx = k3_cppi_desc_pool_alloc(rx_chn->desc_pool);
+ if (!desc_rx) {
+ netdev_err(ndev, "rx push: failed to allocate descriptor\n");
+ return -ENOMEM;
+ }
+ desc_dma = k3_cppi_desc_pool_virt2dma(rx_chn->desc_pool, desc_rx);
+
+ buf_dma = dma_map_single(rx_chn->dma_dev, skb->data, pkt_len, DMA_FROM_DEVICE);
+ if (unlikely(dma_mapping_error(rx_chn->dma_dev, buf_dma))) {
+ k3_cppi_desc_pool_free(rx_chn->desc_pool, desc_rx);
+ netdev_err(ndev, "rx push: failed to map rx pkt buffer\n");
+ return -EINVAL;
+ }
+
+ cppi5_hdesc_init(desc_rx, CPPI5_INFO0_HDESC_EPIB_PRESENT,
+ PRUETH_NAV_PS_DATA_SIZE);
+ k3_udma_glue_rx_dma_to_cppi5_addr(rx_chn->rx_chn, &buf_dma);
+ cppi5_hdesc_attach_buf(desc_rx, buf_dma, skb_tailroom(skb), buf_dma, skb_tailroom(skb));
+
+ swdata = cppi5_hdesc_get_swdata(desc_rx);
+ *swdata = skb;
+
+ return k3_udma_glue_push_rx_chn(rx_chn->rx_chn, 0,
+ desc_rx, desc_dma);
+}
+
+static int emac_rx_packet(struct prueth_emac *emac, u32 flow_id)
+{
+ struct prueth_rx_chn *rx_chn = &emac->rx_chns;
+ u32 buf_dma_len, pkt_len, port_id = 0;
+ struct net_device *ndev = emac->ndev;
+ struct cppi5_host_desc_t *desc_rx;
+ struct sk_buff *skb, *new_skb;
+ dma_addr_t desc_dma, buf_dma;
+ void **swdata;
+ int ret;
+
+ ret = k3_udma_glue_pop_rx_chn(rx_chn->rx_chn, flow_id, &desc_dma);
+ if (ret) {
+ if (ret != -ENODATA)
+ netdev_err(ndev, "rx pop: failed: %d\n", ret);
+ return ret;
+ }
+
+ if (cppi5_desc_is_tdcm(desc_dma)) /* Teardown ? */
+ return 0;
+
+ desc_rx = k3_cppi_desc_pool_dma2virt(rx_chn->desc_pool, desc_dma);
+
+ swdata = cppi5_hdesc_get_swdata(desc_rx);
+ skb = *swdata;
+
+ cppi5_hdesc_get_obuf(desc_rx, &buf_dma, &buf_dma_len);
+ k3_udma_glue_rx_cppi5_to_dma_addr(rx_chn->rx_chn, &buf_dma);
+ pkt_len = cppi5_hdesc_get_pktlen(desc_rx);
+ /* firmware adds 4 CRC bytes, strip them */
+ pkt_len -= 4;
+ cppi5_desc_get_tags_ids(&desc_rx->hdr, &port_id, NULL);
+
+ dma_unmap_single(rx_chn->dma_dev, buf_dma, buf_dma_len, DMA_FROM_DEVICE);
+ k3_cppi_desc_pool_free(rx_chn->desc_pool, desc_rx);
+
+ skb->dev = ndev;
+ if (!netif_running(skb->dev)) {
+ dev_kfree_skb_any(skb);
+ return 0;
+ }
+
+ new_skb = netdev_alloc_skb_ip_align(ndev, PRUETH_MAX_PKT_SIZE);
+ /* if allocation fails we drop the packet but push the
+ * descriptor back to the ring with old skb to prevent a stall
+ */
+ if (!new_skb) {
+ ndev->stats.rx_dropped++;
+ new_skb = skb;
+ } else {
+ /* send the filled skb up the n/w stack */
+ skb_put(skb, pkt_len);
+ skb->protocol = eth_type_trans(skb, ndev);
+ napi_gro_receive(&emac->napi_rx, skb);
+ ndev->stats.rx_bytes += pkt_len;
+ ndev->stats.rx_packets++;
+ }
+
+ /* queue another RX DMA */
+ ret = prueth_dma_rx_push(emac, new_skb, &emac->rx_chns);
+ if (WARN_ON(ret < 0)) {
+ dev_kfree_skb_any(new_skb);
+ ndev->stats.rx_errors++;
+ ndev->stats.rx_dropped++;
+ }
+
+ return ret;
+}
+
+static void prueth_rx_cleanup(void *data, dma_addr_t desc_dma)
+{
+ struct prueth_rx_chn *rx_chn = data;
+ struct cppi5_host_desc_t *desc_rx;
+ struct sk_buff *skb;
+ dma_addr_t buf_dma;
+ u32 buf_dma_len;
+ void **swdata;
+
+ desc_rx = k3_cppi_desc_pool_dma2virt(rx_chn->desc_pool, desc_dma);
+ swdata = cppi5_hdesc_get_swdata(desc_rx);
+ skb = *swdata;
+ cppi5_hdesc_get_obuf(desc_rx, &buf_dma, &buf_dma_len);
+ k3_udma_glue_rx_cppi5_to_dma_addr(rx_chn->rx_chn, &buf_dma);
+
+ dma_unmap_single(rx_chn->dma_dev, buf_dma, buf_dma_len,
+ DMA_FROM_DEVICE);
+ k3_cppi_desc_pool_free(rx_chn->desc_pool, desc_rx);
+
+ dev_kfree_skb_any(skb);
+}
+
+/**
+ * emac_ndo_start_xmit - EMAC Transmit function
+ * @skb: SKB pointer
+ * @ndev: EMAC network adapter
+ *
+ * Called by the system to transmit a packet - we queue the packet in
+ * EMAC hardware transmit queue
+ * Doesn't wait for completion we'll check for TX completion in
+ * emac_tx_complete_packets().
+ *
+ * Returns enum netdev_tx
+ */
+static enum netdev_tx emac_ndo_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct cppi5_host_desc_t *first_desc, *next_desc, *cur_desc;
+ struct prueth_emac *emac = netdev_priv(ndev);
+ struct netdev_queue *netif_txq;
+ struct prueth_tx_chn *tx_chn;
+ dma_addr_t desc_dma, buf_dma;
+ int i, ret = 0, q_idx;
+ void **swdata;
+ u32 pkt_len;
+ u32 *epib;
+
+ pkt_len = skb_headlen(skb);
+ q_idx = skb_get_queue_mapping(skb);
+
+ tx_chn = &emac->tx_chns[q_idx];
+ netif_txq = netdev_get_tx_queue(ndev, q_idx);
+
+ /* Map the linear buffer */
+ buf_dma = dma_map_single(tx_chn->dma_dev, skb->data, pkt_len, DMA_TO_DEVICE);
+ if (dma_mapping_error(tx_chn->dma_dev, buf_dma)) {
+ netdev_err(ndev, "tx: failed to map skb buffer\n");
+ ret = NETDEV_TX_BUSY;
+ goto drop_stop_q;
+ }
+
+ first_desc = k3_cppi_desc_pool_alloc(tx_chn->desc_pool);
+ if (!first_desc) {
+ netdev_dbg(ndev, "tx: failed to allocate descriptor\n");
+ dma_unmap_single(tx_chn->dma_dev, buf_dma, pkt_len, DMA_TO_DEVICE);
+ ret = NETDEV_TX_BUSY;
+ goto drop_stop_q_busy;
+ }
+
+ cppi5_hdesc_init(first_desc, CPPI5_INFO0_HDESC_EPIB_PRESENT,
+ PRUETH_NAV_PS_DATA_SIZE);
+ cppi5_hdesc_set_pkttype(first_desc, 0);
+ epib = first_desc->epib;
+ epib[0] = 0;
+ epib[1] = 0;
+
+ /* set dst tag to indicate internal qid at the firmware which is at
+ * bit8..bit15. bit0..bit7 indicates port num for directed
+ * packets in case of switch mode operation
+ */
+ cppi5_desc_set_tags_ids(&first_desc->hdr, 0, (emac->port_id | (q_idx << 8)));
+ k3_udma_glue_tx_dma_to_cppi5_addr(tx_chn->tx_chn, &buf_dma);
+ cppi5_hdesc_attach_buf(first_desc, buf_dma, pkt_len, buf_dma, pkt_len);
+ swdata = cppi5_hdesc_get_swdata(first_desc);
+ *swdata = skb;
+
+ if (!skb_is_nonlinear(skb))
+ goto tx_push;
+
+ /* Handle the case where skb is fragmented in pages */
+ cur_desc = first_desc;
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+ u32 frag_size = skb_frag_size(frag);
+
+ next_desc = k3_cppi_desc_pool_alloc(tx_chn->desc_pool);
+ if (!next_desc) {
+ netdev_err(ndev,
+ "tx: failed to allocate frag. descriptor\n");
+ ret = NETDEV_TX_BUSY;
+ goto drop_free_descs;
+ }
+
+ buf_dma = skb_frag_dma_map(tx_chn->dma_dev, frag, 0, frag_size,
+ DMA_TO_DEVICE);
+ if (dma_mapping_error(tx_chn->dma_dev, buf_dma)) {
+ netdev_err(ndev, "tx: Failed to map skb page\n");
+ k3_cppi_desc_pool_free(tx_chn->desc_pool, next_desc);
+ ret = NETDEV_TX_BUSY;
+ goto drop_free_descs;
+ }
+
+ cppi5_hdesc_reset_hbdesc(next_desc);
+ k3_udma_glue_tx_dma_to_cppi5_addr(tx_chn->tx_chn, &buf_dma);
+ cppi5_hdesc_attach_buf(next_desc,
+ buf_dma, frag_size, buf_dma, frag_size);
+
+ desc_dma = k3_cppi_desc_pool_virt2dma(tx_chn->desc_pool,
+ next_desc);
+ k3_udma_glue_tx_dma_to_cppi5_addr(tx_chn->tx_chn, &desc_dma);
+ cppi5_hdesc_link_hbdesc(cur_desc, desc_dma);
+
+ pkt_len += frag_size;
+ cur_desc = next_desc;
+ }
+ WARN_ON(pkt_len != skb->len);
+
+tx_push:
+ /* report bql before sending packet */
+ netdev_tx_sent_queue(netif_txq, pkt_len);
+
+ cppi5_hdesc_set_pktlen(first_desc, pkt_len);
+ desc_dma = k3_cppi_desc_pool_virt2dma(tx_chn->desc_pool, first_desc);
+ /* cppi5_desc_dump(first_desc, 64); */
+
+ skb_tx_timestamp(skb); /* SW timestamp if SKBTX_IN_PROGRESS not set */
+ ret = k3_udma_glue_push_tx_chn(tx_chn->tx_chn, first_desc, desc_dma);
+ if (ret) {
+ netdev_err(ndev, "tx: push failed: %d\n", ret);
+ goto drop_free_descs;
+ }
+
+ if (k3_cppi_desc_pool_avail(tx_chn->desc_pool) < MAX_SKB_FRAGS) {
+ netif_tx_stop_queue(netif_txq);
+ /* Barrier, so that stop_queue visible to other cpus */
+ smp_mb__after_atomic();
+
+ if (k3_cppi_desc_pool_avail(tx_chn->desc_pool) >=
+ MAX_SKB_FRAGS)
+ netif_tx_wake_queue(netif_txq);
+ }
+
+ return NETDEV_TX_OK;
+
+drop_free_descs:
+ prueth_xmit_free(tx_chn, first_desc);
+drop_stop_q:
+ netif_tx_stop_queue(netif_txq);
+ dev_kfree_skb_any(skb);
+
+ /* error */
+ ndev->stats.tx_dropped++;
+ netdev_err(ndev, "tx: error: %d\n", ret);
+
+ return ret;
+
+drop_stop_q_busy:
+ netif_tx_stop_queue(netif_txq);
+ return NETDEV_TX_BUSY;
+}
+
+static void prueth_tx_cleanup(void *data, dma_addr_t desc_dma)
+{
+ struct prueth_tx_chn *tx_chn = data;
+ struct cppi5_host_desc_t *desc_tx;
+ struct sk_buff *skb;
+ void **swdata;
+
+ desc_tx = k3_cppi_desc_pool_dma2virt(tx_chn->desc_pool, desc_dma);
+ swdata = cppi5_hdesc_get_swdata(desc_tx);
+ skb = *(swdata);
+ prueth_xmit_free(tx_chn, desc_tx);
+
+ dev_kfree_skb_any(skb);
+}
+
+static irqreturn_t prueth_rx_irq(int irq, void *dev_id)
+{
+ struct prueth_emac *emac = dev_id;
+
+ disable_irq_nosync(irq);
+ napi_schedule(&emac->napi_rx);
+
+ return IRQ_HANDLED;
+}
+
+struct icssg_firmwares {
+ char *pru;
+ char *rtu;
+ char *txpru;
+};
+
+static struct icssg_firmwares icssg_emac_firmwares[] = {
+ {
+ .pru = "ti-pruss/am65x-sr2-pru0-prueth-fw.elf",
+ .rtu = "ti-pruss/am65x-sr2-rtu0-prueth-fw.elf",
+ .txpru = "ti-pruss/am65x-sr2-txpru0-prueth-fw.elf",
+ },
+ {
+ .pru = "ti-pruss/am65x-sr2-pru1-prueth-fw.elf",
+ .rtu = "ti-pruss/am65x-sr2-rtu1-prueth-fw.elf",
+ .txpru = "ti-pruss/am65x-sr2-txpru1-prueth-fw.elf",
+ }
+};
+
+static int prueth_emac_start(struct prueth *prueth, struct prueth_emac *emac)
+{
+ struct icssg_firmwares *firmwares;
+ struct device *dev = prueth->dev;
+ int slice, ret;
+
+ firmwares = icssg_emac_firmwares;
+
+ slice = prueth_emac_slice(emac);
+ if (slice < 0) {
+ netdev_err(emac->ndev, "invalid port\n");
+ return -EINVAL;
+ }
+
+ ret = icssg_config(prueth, emac, slice);
+ if (ret)
+ return ret;
+
+ ret = rproc_set_firmware(prueth->pru[slice], firmwares[slice].pru);
+ ret = rproc_boot(prueth->pru[slice]);
+ if (ret) {
+ dev_err(dev, "failed to boot PRU%d: %d\n", slice, ret);
+ return -EINVAL;
+ }
+
+ ret = rproc_set_firmware(prueth->rtu[slice], firmwares[slice].rtu);
+ ret = rproc_boot(prueth->rtu[slice]);
+ if (ret) {
+ dev_err(dev, "failed to boot RTU%d: %d\n", slice, ret);
+ goto halt_pru;
+ }
+
+ ret = rproc_set_firmware(prueth->txpru[slice], firmwares[slice].txpru);
+ ret = rproc_boot(prueth->txpru[slice]);
+ if (ret) {
+ dev_err(dev, "failed to boot TX_PRU%d: %d\n", slice, ret);
+ goto halt_rtu;
+ }
+
+ emac->fw_running = 1;
+ return 0;
+
+halt_rtu:
+ rproc_shutdown(prueth->rtu[slice]);
+
+halt_pru:
+ rproc_shutdown(prueth->pru[slice]);
+
+ return ret;
+}
+
+static void prueth_emac_stop(struct prueth_emac *emac)
+{
+ struct prueth *prueth = emac->prueth;
+ int slice;
+
+ switch (emac->port_id) {
+ case PRUETH_PORT_MII0:
+ slice = ICSS_SLICE0;
+ break;
+ case PRUETH_PORT_MII1:
+ slice = ICSS_SLICE1;
+ break;
+ default:
+ netdev_err(emac->ndev, "invalid port\n");
+ return;
+ }
+
+ emac->fw_running = 0;
+ rproc_shutdown(prueth->txpru[slice]);
+ rproc_shutdown(prueth->rtu[slice]);
+ rproc_shutdown(prueth->pru[slice]);
+}
+
+/* called back by PHY layer if there is change in link state of hw port*/
+static void emac_adjust_link(struct net_device *ndev)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ struct phy_device *phydev = ndev->phydev;
+ struct prueth *prueth = emac->prueth;
+ bool new_state = false;
+ unsigned long flags;
+
+ if (phydev->link) {
+ /* check the mode of operation - full/half duplex */
+ if (phydev->duplex != emac->duplex) {
+ new_state = true;
+ emac->duplex = phydev->duplex;
+ }
+ if (phydev->speed != emac->speed) {
+ new_state = true;
+ emac->speed = phydev->speed;
+ }
+ if (!emac->link) {
+ new_state = true;
+ emac->link = 1;
+ }
+ } else if (emac->link) {
+ new_state = true;
+ emac->link = 0;
+
+ /* f/w should support 100 & 1000 */
+ emac->speed = SPEED_1000;
+
+ /* half duplex may not be supported by f/w */
+ emac->duplex = DUPLEX_FULL;
+ }
+
+ if (new_state) {
+ phy_print_status(phydev);
+
+ /* update RGMII and MII configuration based on PHY negotiated
+ * values
+ */
+ if (emac->link) {
+ /* Set the RGMII cfg for gig en and full duplex */
+ icssg_update_rgmii_cfg(prueth->miig_rt, emac);
+
+ /* update the Tx IPG based on 100M/1G speed */
+ spin_lock_irqsave(&emac->lock, flags);
+ icssg_config_ipg(emac);
+ spin_unlock_irqrestore(&emac->lock, flags);
+ icssg_config_set_speed(emac);
+ emac_set_port_state(emac, ICSSG_EMAC_PORT_FORWARD);
+
+ } else {
+ emac_set_port_state(emac, ICSSG_EMAC_PORT_DISABLE);
+ }
+ }
+
+ if (emac->link) {
+ /* reactivate the transmit queue */
+ netif_tx_wake_all_queues(ndev);
+ } else {
+ netif_tx_stop_all_queues(ndev);
+ }
+}
+
+static int emac_napi_rx_poll(struct napi_struct *napi_rx, int budget)
+{
+ struct prueth_emac *emac = prueth_napi_to_emac(napi_rx);
+ int rx_flow = PRUETH_RX_FLOW_DATA;
+ int flow = PRUETH_MAX_RX_FLOWS;
+ int num_rx = 0;
+ int cur_budget;
+ int ret;
+
+ while (flow--) {
+ cur_budget = budget - num_rx;
+
+ while (cur_budget--) {
+ ret = emac_rx_packet(emac, flow);
+ if (ret)
+ break;
+ num_rx++;
+ }
+
+ if (num_rx >= budget)
+ break;
+ }
+
+ if (num_rx < budget) {
+ napi_complete(napi_rx);
+ enable_irq(emac->rx_chns.irq[rx_flow]);
+ }
+
+ return num_rx;
+}
+
+static int prueth_prepare_rx_chan(struct prueth_emac *emac,
+ struct prueth_rx_chn *chn,
+ int buf_size)
+{
+ struct sk_buff *skb;
+ int i, ret;
+
+ for (i = 0; i < chn->descs_num; i++) {
+ skb = __netdev_alloc_skb_ip_align(NULL, buf_size, GFP_KERNEL);
+ if (!skb)
+ return -ENOMEM;
+
+ ret = prueth_dma_rx_push(emac, skb, chn);
+ if (ret < 0) {
+ netdev_err(emac->ndev,
+ "cannot submit skb for rx chan %s ret %d\n",
+ chn->name, ret);
+ kfree_skb(skb);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static void prueth_reset_tx_chan(struct prueth_emac *emac, int ch_num,
+ bool free_skb)
+{
+ int i;
+
+ for (i = 0; i < ch_num; i++) {
+ if (free_skb)
+ k3_udma_glue_reset_tx_chn(emac->tx_chns[i].tx_chn,
+ &emac->tx_chns[i],
+ prueth_tx_cleanup);
+ k3_udma_glue_disable_tx_chn(emac->tx_chns[i].tx_chn);
+ }
+}
+
+static void prueth_reset_rx_chan(struct prueth_rx_chn *chn,
+ int num_flows, bool disable)
+{
+ int i;
+
+ for (i = 0; i < num_flows; i++)
+ k3_udma_glue_reset_rx_chn(chn->rx_chn, i, chn,
+ prueth_rx_cleanup, !!i);
+ if (disable)
+ k3_udma_glue_disable_rx_chn(chn->rx_chn);
+}
+
+static int emac_phy_connect(struct prueth_emac *emac)
+{
+ struct prueth *prueth = emac->prueth;
+ struct net_device *ndev = emac->ndev;
+ /* connect PHY */
+ ndev->phydev = of_phy_connect(emac->ndev, emac->phy_node,
+ &emac_adjust_link, 0,
+ emac->phy_if);
+ if (!ndev->phydev) {
+ dev_err(prueth->dev, "couldn't connect to phy %s\n",
+ emac->phy_node->full_name);
+ return -ENODEV;
+ }
+
+ /* remove unsupported modes */
+ phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+ phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_10baseT_Full_BIT);
+ phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+ phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+ phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_Pause_BIT);
+ phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_Asym_Pause_BIT);
+
+ if (emac->phy_if == PHY_INTERFACE_MODE_MII)
+ phy_set_max_speed(ndev->phydev, SPEED_100);
+
+ return 0;
+}
+
+/**
+ * emac_ndo_open - EMAC device open
+ * @ndev: network adapter device
+ *
+ * Called when system wants to start the interface.
+ *
+ * Returns 0 for a successful open, or appropriate error code
+ */
+static int emac_ndo_open(struct net_device *ndev)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ int ret, i, num_data_chn = emac->tx_ch_num;
+ struct prueth *prueth = emac->prueth;
+ int slice = prueth_emac_slice(emac);
+ struct device *dev = prueth->dev;
+ int max_rx_flows;
+ int rx_flow;
+
+ /* clear SMEM and MSMC settings for all slices */
+ if (!prueth->emacs_initialized) {
+ memset_io(prueth->msmcram.va, 0, prueth->msmcram.size);
+ memset_io(prueth->shram.va, 0, ICSSG_CONFIG_OFFSET_SLICE1 * PRUETH_NUM_MACS);
+ }
+
+ /* set h/w MAC as user might have re-configured */
+ ether_addr_copy(emac->mac_addr, ndev->dev_addr);
+
+ icssg_class_set_mac_addr(prueth->miig_rt, slice, emac->mac_addr);
+ icssg_ft1_set_mac_addr(prueth->miig_rt, slice, emac->mac_addr);
+
+ icssg_class_default(prueth->miig_rt, slice, 0);
+
+ /* Notify the stack of the actual queue counts. */
+ ret = netif_set_real_num_tx_queues(ndev, num_data_chn);
+ if (ret) {
+ dev_err(dev, "cannot set real number of tx queues\n");
+ return ret;
+ }
+
+ init_completion(&emac->cmd_complete);
+ ret = prueth_init_tx_chns(emac);
+ if (ret) {
+ dev_err(dev, "failed to init tx channel: %d\n", ret);
+ return ret;
+ }
+
+ max_rx_flows = PRUETH_MAX_RX_FLOWS;
+ ret = prueth_init_rx_chns(emac, &emac->rx_chns, "rx",
+ max_rx_flows, PRUETH_MAX_RX_DESC);
+ if (ret) {
+ dev_err(dev, "failed to init rx channel: %d\n", ret);
+ goto cleanup_tx;
+ }
+
+ ret = prueth_ndev_add_tx_napi(emac);
+ if (ret)
+ goto cleanup_rx;
+
+ /* we use only the highest priority flow for now i.e. @irq[3] */
+ rx_flow = PRUETH_RX_FLOW_DATA;
+ ret = request_irq(emac->rx_chns.irq[rx_flow], prueth_rx_irq,
+ IRQF_TRIGGER_HIGH, dev_name(dev), emac);
+ if (ret) {
+ dev_err(dev, "unable to request RX IRQ\n");
+ goto cleanup_napi;
+ }
+
+ /* reset and start PRU firmware */
+ ret = prueth_emac_start(prueth, emac);
+ if (ret)
+ goto free_rx_irq;
+
+ icssg_mii_update_mtu(prueth->mii_rt, slice, ndev->max_mtu);
+
+ /* Prepare RX */
+ ret = prueth_prepare_rx_chan(emac, &emac->rx_chns, PRUETH_MAX_PKT_SIZE);
+ if (ret)
+ goto stop;
+
+ ret = k3_udma_glue_enable_rx_chn(emac->rx_chns.rx_chn);
+ if (ret)
+ goto reset_rx_chn;
+
+ for (i = 0; i < emac->tx_ch_num; i++) {
+ ret = k3_udma_glue_enable_tx_chn(emac->tx_chns[i].tx_chn);
+ if (ret)
+ goto reset_tx_chan;
+ }
+
+ /* Enable NAPI in Tx and Rx direction */
+ for (i = 0; i < emac->tx_ch_num; i++)
+ napi_enable(&emac->tx_chns[i].napi_tx);
+ napi_enable(&emac->napi_rx);
+
+ /* start PHY */
+ phy_start(ndev->phydev);
+
+ prueth->emacs_initialized++;
+
+ return 0;
+
+reset_tx_chan:
+ /* Since interface is not yet up, there is wouldn't be
+ * any SKB for completion. So set false to free_skb
+ */
+ prueth_reset_tx_chan(emac, i, false);
+reset_rx_chn:
+ prueth_reset_rx_chan(&emac->rx_chns, max_rx_flows, false);
+stop:
+ prueth_emac_stop(emac);
+free_rx_irq:
+ free_irq(emac->rx_chns.irq[rx_flow], emac);
+cleanup_napi:
+ prueth_ndev_del_tx_napi(emac, emac->tx_ch_num);
+cleanup_rx:
+ prueth_cleanup_rx_chns(emac, &emac->rx_chns, max_rx_flows);
+cleanup_tx:
+ prueth_cleanup_tx_chns(emac);
+
+ return ret;
+}
+
+/**
+ * emac_ndo_stop - EMAC device stop
+ * @ndev: network adapter device
+ *
+ * Called when system wants to stop or down the interface.
+ */
+static int emac_ndo_stop(struct net_device *ndev)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+ struct prueth *prueth = emac->prueth;
+ int rx_flow = PRUETH_RX_FLOW_DATA;
+ int max_rx_flows;
+ int ret, i;
+
+ /* inform the upper layers. */
+ netif_tx_stop_all_queues(ndev);
+
+ /* block packets from wire */
+ if (ndev->phydev)
+ phy_stop(ndev->phydev);
+
+ icssg_class_disable(prueth->miig_rt, prueth_emac_slice(emac));
+
+ atomic_set(&emac->tdown_cnt, emac->tx_ch_num);
+ /* ensure new tdown_cnt value is visible */
+ smp_mb__after_atomic();
+ /* tear down and disable UDMA channels */
+ reinit_completion(&emac->tdown_complete);
+ for (i = 0; i < emac->tx_ch_num; i++)
+ k3_udma_glue_tdown_tx_chn(emac->tx_chns[i].tx_chn, false);
+
+ ret = wait_for_completion_timeout(&emac->tdown_complete,
+ msecs_to_jiffies(1000));
+ if (!ret)
+ netdev_err(ndev, "tx teardown timeout\n");
+
+ prueth_reset_tx_chan(emac, emac->tx_ch_num, true);
+ for (i = 0; i < emac->tx_ch_num; i++)
+ napi_disable(&emac->tx_chns[i].napi_tx);
+
+ max_rx_flows = PRUETH_MAX_RX_FLOWS;
+ k3_udma_glue_tdown_rx_chn(emac->rx_chns.rx_chn, true);
+
+ prueth_reset_rx_chan(&emac->rx_chns, max_rx_flows, true);
+
+ napi_disable(&emac->napi_rx);
+
+ cancel_work_sync(&emac->rx_mode_work);
+ /* stop PRUs */
+ prueth_emac_stop(emac);
+
+ free_irq(emac->rx_chns.irq[rx_flow], emac);
+ prueth_ndev_del_tx_napi(emac, emac->tx_ch_num);
+ prueth_cleanup_tx_chns(emac);
+
+ prueth_cleanup_rx_chns(emac, &emac->rx_chns, max_rx_flows);
+ prueth_cleanup_tx_chns(emac);
+
+ prueth->emacs_initialized--;
+
+ return 0;
+}
+
+static void emac_ndo_tx_timeout(struct net_device *ndev, unsigned int txqueue)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ if (netif_msg_tx_err(emac))
+ netdev_err(ndev, "xmit timeout");
+
+ ndev->stats.tx_errors++;
+}
+
+static void emac_ndo_set_rx_mode_work(struct work_struct *work)
+{
+ struct prueth_emac *emac = container_of(work, struct prueth_emac, rx_mode_work);
+ struct net_device *ndev = emac->ndev;
+ bool promisc, allmulti;
+
+ if (!netif_running(ndev))
+ return;
+
+ promisc = ndev->flags & IFF_PROMISC;
+ allmulti = ndev->flags & IFF_ALLMULTI;
+ emac_set_port_state(emac, ICSSG_EMAC_PORT_UC_FLOODING_DISABLE);
+ emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_DISABLE);
+
+ if (promisc) {
+ emac_set_port_state(emac, ICSSG_EMAC_PORT_UC_FLOODING_ENABLE);
+ emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_ENABLE);
+ return;
+ }
+
+ if (allmulti) {
+ emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_ENABLE);
+ return;
+ }
+
+ if (!netdev_mc_empty(ndev)) {
+ emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_ENABLE);
+ return;
+ }
+}
+
+/**
+ * emac_ndo_set_rx_mode - EMAC set receive mode function
+ * @ndev: The EMAC network adapter
+ *
+ * Called when system wants to set the receive mode of the device.
+ *
+ */
+static void emac_ndo_set_rx_mode(struct net_device *ndev)
+{
+ struct prueth_emac *emac = netdev_priv(ndev);
+
+ queue_work(emac->cmd_wq, &emac->rx_mode_work);
+}
+
+static int emac_ndo_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
+{
+ return phy_do_ioctl(ndev, ifr, cmd);
+}
+
+static const struct net_device_ops emac_netdev_ops = {
+ .ndo_open = emac_ndo_open,
+ .ndo_stop = emac_ndo_stop,
+ .ndo_start_xmit = emac_ndo_start_xmit,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_tx_timeout = emac_ndo_tx_timeout,
+ .ndo_set_rx_mode = emac_ndo_set_rx_mode,
+ .ndo_eth_ioctl = emac_ndo_ioctl,
+};
+
+/* get emac_port corresponding to eth_node name */
+static int prueth_node_port(struct device_node *eth_node)
+{
+ u32 port_id;
+ int ret;
+
+ ret = of_property_read_u32(eth_node, "reg", &port_id);
+ if (ret)
+ return ret;
+
+ if (port_id == 0)
+ return PRUETH_PORT_MII0;
+ else if (port_id == 1)
+ return PRUETH_PORT_MII1;
+ else
+ return -EINVAL;
+}
+
+/* get MAC instance corresponding to eth_node name */
+static int prueth_node_mac(struct device_node *eth_node)
+{
+ u32 port_id;
+ int ret;
+
+ ret = of_property_read_u32(eth_node, "reg", &port_id);
+ if (ret)
+ return ret;
+
+ if (port_id == 0)
+ return PRUETH_MAC0;
+ else if (port_id == 1)
+ return PRUETH_MAC1;
+ else
+ return -EINVAL;
+}
+
+extern const struct ethtool_ops icssg_ethtool_ops;
+
+static int prueth_netdev_init(struct prueth *prueth,
+ struct device_node *eth_node)
+{
+ int ret, num_tx_chn = PRUETH_MAX_TX_QUEUES;
+ struct prueth_emac *emac;
+ struct net_device *ndev;
+ enum prueth_port port;
+ enum prueth_mac mac;
+
+ port = prueth_node_port(eth_node);
+ if (port < 0)
+ return -EINVAL;
+
+ mac = prueth_node_mac(eth_node);
+ if (mac < 0)
+ return -EINVAL;
+
+ ndev = alloc_etherdev_mq(sizeof(*emac), num_tx_chn);
+ if (!ndev)
+ return -ENOMEM;
+
+ emac = netdev_priv(ndev);
+ prueth->emac[mac] = emac;
+ emac->prueth = prueth;
+ emac->ndev = ndev;
+ emac->port_id = port;
+ emac->cmd_wq = create_singlethread_workqueue("icssg_cmd_wq");
+ if (!emac->cmd_wq) {
+ ret = -ENOMEM;
+ goto free_ndev;
+ }
+ INIT_WORK(&emac->rx_mode_work, emac_ndo_set_rx_mode_work);
+
+ ret = pruss_request_mem_region(prueth->pruss,
+ port == PRUETH_PORT_MII0 ?
+ PRUSS_MEM_DRAM0 : PRUSS_MEM_DRAM1,
+ &emac->dram);
+ if (ret) {
+ dev_err(prueth->dev, "unable to get DRAM: %d\n", ret);
+ ret = -ENOMEM;
+ goto free_wq;
+ }
+
+ emac->tx_ch_num = 1;
+
+ SET_NETDEV_DEV(ndev, prueth->dev);
+ spin_lock_init(&emac->lock);
+ mutex_init(&emac->cmd_lock);
+
+ emac->phy_node = of_parse_phandle(eth_node, "phy-handle", 0);
+ if (!emac->phy_node && !of_phy_is_fixed_link(eth_node)) {
+ dev_err(prueth->dev, "couldn't find phy-handle\n");
+ ret = -ENODEV;
+ goto free;
+ } else if (of_phy_is_fixed_link(eth_node)) {
+ ret = of_phy_register_fixed_link(eth_node);
+ if (ret) {
+ ret = dev_err_probe(prueth->dev, ret,
+ "failed to register fixed-link phy\n");
+ goto free;
+ }
+
+ emac->phy_node = eth_node;
+ }
+
+ ret = of_get_phy_mode(eth_node, &emac->phy_if);
+ if (ret) {
+ dev_err(prueth->dev, "could not get phy-mode property\n");
+ goto free;
+ }
+
+ if (emac->phy_if != PHY_INTERFACE_MODE_MII &&
+ !phy_interface_mode_is_rgmii(emac->phy_if)) {
+ dev_err(prueth->dev, "PHY mode unsupported %s\n", phy_modes(emac->phy_if));
+ ret = -EINVAL;
+ goto free;
+ }
+
+ /* AM65 SR2.0 has TX Internal delay always enabled by hardware
+ * and it is not possible to disable TX Internal delay. The below
+ * switch case block describes how we handle different phy modes
+ * based on hardware restriction.
+ */
+ switch (emac->phy_if) {
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ emac->phy_if = PHY_INTERFACE_MODE_RGMII_RXID;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ emac->phy_if = PHY_INTERFACE_MODE_RGMII;
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ dev_err(prueth->dev, "RGMII mode without TX delay is not supported");
+ return -EINVAL;
+ default:
+ break;
+ }
+
+ /* get mac address from DT and set private and netdev addr */
+ ret = of_get_ethdev_address(eth_node, ndev);
+ if (!is_valid_ether_addr(ndev->dev_addr)) {
+ eth_hw_addr_random(ndev);
+ dev_warn(prueth->dev, "port %d: using random MAC addr: %pM\n",
+ port, ndev->dev_addr);
+ }
+ ether_addr_copy(emac->mac_addr, ndev->dev_addr);
+
+ ndev->min_mtu = PRUETH_MIN_PKT_SIZE;
+ ndev->max_mtu = PRUETH_MAX_MTU;
+ ndev->netdev_ops = &emac_netdev_ops;
+ ndev->ethtool_ops = &icssg_ethtool_ops;
+ ndev->hw_features = NETIF_F_SG;
+ ndev->features = ndev->hw_features;
+
+ netif_napi_add(ndev, &emac->napi_rx,
+ emac_napi_rx_poll);
+
+ return 0;
+
+free:
+ pruss_release_mem_region(prueth->pruss, &emac->dram);
+free_wq:
+ destroy_workqueue(emac->cmd_wq);
+free_ndev:
+ free_netdev(ndev);
+ prueth->emac[mac] = NULL;
+
+ return ret;
+}
+
+static void prueth_netdev_exit(struct prueth *prueth,
+ struct device_node *eth_node)
+{
+ struct prueth_emac *emac;
+ enum prueth_mac mac;
+
+ mac = prueth_node_mac(eth_node);
+ if (mac < 0)
+ return;
+
+ emac = prueth->emac[mac];
+ if (!emac)
+ return;
+
+ if (of_phy_is_fixed_link(emac->phy_node))
+ of_phy_deregister_fixed_link(emac->phy_node);
+
+ netif_napi_del(&emac->napi_rx);
+
+ pruss_release_mem_region(prueth->pruss, &emac->dram);
+ destroy_workqueue(emac->cmd_wq);
+ free_netdev(emac->ndev);
+ prueth->emac[mac] = NULL;
+}
+
+static int prueth_get_cores(struct prueth *prueth, int slice)
+{
+ struct device *dev = prueth->dev;
+ enum pruss_pru_id pruss_id;
+ struct device_node *np;
+ int idx = -1, ret;
+
+ np = dev->of_node;
+
+ switch (slice) {
+ case ICSS_SLICE0:
+ idx = 0;
+ break;
+ case ICSS_SLICE1:
+ idx = 3;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ prueth->pru[slice] = pru_rproc_get(np, idx, &pruss_id);
+ if (IS_ERR(prueth->pru[slice])) {
+ ret = PTR_ERR(prueth->pru[slice]);
+ prueth->pru[slice] = NULL;
+ return dev_err_probe(dev, ret, "unable to get PRU%d\n", slice);
+ }
+ prueth->pru_id[slice] = pruss_id;
+
+ idx++;
+ prueth->rtu[slice] = pru_rproc_get(np, idx, NULL);
+ if (IS_ERR(prueth->rtu[slice])) {
+ ret = PTR_ERR(prueth->rtu[slice]);
+ prueth->rtu[slice] = NULL;
+ return dev_err_probe(dev, ret, "unable to get RTU%d\n", slice);
+ }
+
+ idx++;
+ prueth->txpru[slice] = pru_rproc_get(np, idx, NULL);
+ if (IS_ERR(prueth->txpru[slice])) {
+ ret = PTR_ERR(prueth->txpru[slice]);
+ prueth->txpru[slice] = NULL;
+ return dev_err_probe(dev, ret, "unable to get TX_PRU%d\n", slice);
+ }
+
+ return 0;
+}
+
+static void prueth_put_cores(struct prueth *prueth, int slice)
+{
+ if (prueth->txpru[slice])
+ pru_rproc_put(prueth->txpru[slice]);
+
+ if (prueth->rtu[slice])
+ pru_rproc_put(prueth->rtu[slice]);
+
+ if (prueth->pru[slice])
+ pru_rproc_put(prueth->pru[slice]);
+}
+
+static const struct of_device_id prueth_dt_match[];
+
+static int prueth_probe(struct platform_device *pdev)
+{
+ struct device_node *eth_node, *eth0_node, *eth1_node, *eth_ports_node;
+ struct genpool_data_align gp_data = {
+ .align = SZ_64K,
+ };
+ const struct of_device_id *match;
+ struct device *dev = &pdev->dev;
+ struct device_node *np;
+ struct prueth *prueth;
+ struct pruss *pruss;
+ u32 msmc_ram_size;
+ int i, ret;
+
+ np = dev->of_node;
+
+ match = of_match_device(prueth_dt_match, dev);
+ if (!match)
+ return -ENODEV;
+
+ prueth = devm_kzalloc(dev, sizeof(*prueth), GFP_KERNEL);
+ if (!prueth)
+ return -ENOMEM;
+
+ dev_set_drvdata(dev, prueth);
+ prueth->pdev = pdev;
+ prueth->pdata = *(const struct prueth_pdata *)match->data;
+
+ prueth->dev = dev;
+ eth_ports_node = of_get_child_by_name(np, "ethernet-ports");
+ if (!eth_ports_node)
+ return -ENOENT;
+
+ for_each_child_of_node(eth_ports_node, eth_node) {
+ u32 reg;
+
+ if (strcmp(eth_node->name, "port"))
+ continue;
+ ret = of_property_read_u32(eth_node, "reg", ®);
+ if (ret < 0) {
+ dev_err(dev, "%pOF error reading port_id %d\n",
+ eth_node, ret);
+ }
+
+ of_node_get(eth_node);
+
+ if (reg == 0) {
+ eth0_node = eth_node;
+ if (!of_device_is_available(eth0_node)) {
+ of_node_put(eth0_node);
+ eth0_node = NULL;
+ }
+ } else if (reg == 1) {
+ eth1_node = eth_node;
+ if (!of_device_is_available(eth1_node)) {
+ of_node_put(eth1_node);
+ eth1_node = NULL;
+ }
+ } else {
+ dev_err(dev, "port reg should be 0 or 1\n");
+ }
+ }
+
+ of_node_put(eth_ports_node);
+
+ /* At least one node must be present and available else we fail */
+ if (!eth0_node && !eth1_node) {
+ dev_err(dev, "neither port0 nor port1 node available\n");
+ return -ENODEV;
+ }
+
+ if (eth0_node == eth1_node) {
+ dev_err(dev, "port0 and port1 can't have same reg\n");
+ of_node_put(eth0_node);
+ return -ENODEV;
+ }
+
+ prueth->eth_node[PRUETH_MAC0] = eth0_node;
+ prueth->eth_node[PRUETH_MAC1] = eth1_node;
+
+ prueth->miig_rt = syscon_regmap_lookup_by_phandle(np, "ti,mii-g-rt");
+ if (IS_ERR(prueth->miig_rt)) {
+ dev_err(dev, "couldn't get ti,mii-g-rt syscon regmap\n");
+ return -ENODEV;
+ }
+
+ prueth->mii_rt = syscon_regmap_lookup_by_phandle(np, "ti,mii-rt");
+ if (IS_ERR(prueth->mii_rt)) {
+ dev_err(dev, "couldn't get ti,mii-rt syscon regmap\n");
+ return -ENODEV;
+ }
+
+ if (eth0_node) {
+ ret = prueth_get_cores(prueth, ICSS_SLICE0);
+ if (ret)
+ goto put_cores;
+ }
+
+ if (eth1_node) {
+ ret = prueth_get_cores(prueth, ICSS_SLICE1);
+ if (ret)
+ goto put_cores;
+ }
+
+ pruss = pruss_get(eth0_node ?
+ prueth->pru[ICSS_SLICE0] : prueth->pru[ICSS_SLICE1]);
+ if (IS_ERR(pruss)) {
+ ret = PTR_ERR(pruss);
+ dev_err(dev, "unable to get pruss handle\n");
+ goto put_cores;
+ }
+
+ prueth->pruss = pruss;
+
+ ret = pruss_request_mem_region(pruss, PRUSS_MEM_SHRD_RAM2,
+ &prueth->shram);
+ if (ret) {
+ dev_err(dev, "unable to get PRUSS SHRD RAM2: %d\n", ret);
+ pruss_put(prueth->pruss);
+ }
+
+ prueth->sram_pool = of_gen_pool_get(np, "sram", 0);
+ if (!prueth->sram_pool) {
+ dev_err(dev, "unable to get SRAM pool\n");
+ ret = -ENODEV;
+
+ goto put_mem;
+ }
+
+ msmc_ram_size = MSMC_RAM_SIZE;
+
+ /* NOTE: FW bug needs buffer base to be 64KB aligned */
+ prueth->msmcram.va =
+ (void __iomem *)gen_pool_alloc_algo(prueth->sram_pool,
+ msmc_ram_size,
+ gen_pool_first_fit_align,
+ &gp_data);
+
+ if (!prueth->msmcram.va) {
+ ret = -ENOMEM;
+ dev_err(dev, "unable to allocate MSMC resource\n");
+ goto put_mem;
+ }
+ prueth->msmcram.pa = gen_pool_virt_to_phys(prueth->sram_pool,
+ (unsigned long)prueth->msmcram.va);
+ prueth->msmcram.size = msmc_ram_size;
+ memset(prueth->msmcram.va, 0, msmc_ram_size);
+ dev_dbg(dev, "sram: pa %llx va %p size %zx\n", prueth->msmcram.pa,
+ prueth->msmcram.va, prueth->msmcram.size);
+
+ /* setup netdev interfaces */
+ if (eth0_node) {
+ ret = prueth_netdev_init(prueth, eth0_node);
+ if (ret) {
+ dev_err_probe(dev, ret, "netdev init %s failed\n",
+ eth0_node->name);
+ goto netdev_exit;
+ }
+ }
+
+ if (eth1_node) {
+ ret = prueth_netdev_init(prueth, eth1_node);
+ if (ret) {
+ dev_err_probe(dev, ret, "netdev init %s failed\n",
+ eth1_node->name);
+ goto netdev_exit;
+ }
+ }
+
+ /* register the network devices */
+ if (eth0_node) {
+ ret = register_netdev(prueth->emac[PRUETH_MAC0]->ndev);
+ if (ret) {
+ dev_err(dev, "can't register netdev for port MII0");
+ goto netdev_exit;
+ }
+
+ prueth->registered_netdevs[PRUETH_MAC0] = prueth->emac[PRUETH_MAC0]->ndev;
+
+ emac_phy_connect(prueth->emac[PRUETH_MAC0]);
+ phy_attached_info(prueth->emac[PRUETH_MAC0]->ndev->phydev);
+ }
+
+ if (eth1_node) {
+ ret = register_netdev(prueth->emac[PRUETH_MAC1]->ndev);
+ if (ret) {
+ dev_err(dev, "can't register netdev for port MII1");
+ goto netdev_unregister;
+ }
+
+ prueth->registered_netdevs[PRUETH_MAC1] = prueth->emac[PRUETH_MAC1]->ndev;
+ emac_phy_connect(prueth->emac[PRUETH_MAC1]);
+ phy_attached_info(prueth->emac[PRUETH_MAC1]->ndev->phydev);
+ }
+
+ dev_info(dev, "TI PRU ethernet driver initialized: %s EMAC mode\n",
+ (!eth0_node || !eth1_node) ? "single" : "dual");
+
+ if (eth1_node)
+ of_node_put(eth1_node);
+ if (eth0_node)
+ of_node_put(eth0_node);
+ return 0;
+
+netdev_unregister:
+ for (i = 0; i < PRUETH_NUM_MACS; i++) {
+ if (!prueth->registered_netdevs[i])
+ continue;
+ if (prueth->emac[i]->ndev->phydev) {
+ phy_disconnect(prueth->emac[i]->ndev->phydev);
+ prueth->emac[i]->ndev->phydev = NULL;
+ }
+ unregister_netdev(prueth->registered_netdevs[i]);
+ }
+
+netdev_exit:
+ for (i = 0; i < PRUETH_NUM_MACS; i++) {
+ eth_node = prueth->eth_node[i];
+ if (!eth_node)
+ continue;
+
+ prueth_netdev_exit(prueth, eth_node);
+ }
+
+ gen_pool_free(prueth->sram_pool,
+ (unsigned long)prueth->msmcram.va, msmc_ram_size);
+
+put_mem:
+ pruss_release_mem_region(prueth->pruss, &prueth->shram);
+ pruss_put(prueth->pruss);
+
+put_cores:
+ if (eth1_node) {
+ prueth_put_cores(prueth, ICSS_SLICE1);
+ of_node_put(eth1_node);
+ }
+
+ if (eth0_node) {
+ prueth_put_cores(prueth, ICSS_SLICE0);
+ of_node_put(eth0_node);
+ }
+
+ return ret;
+}
+
+static int prueth_remove(struct platform_device *pdev)
+{
+ struct prueth *prueth = platform_get_drvdata(pdev);
+ struct device_node *eth_node;
+ int i;
+
+ for (i = 0; i < PRUETH_NUM_MACS; i++) {
+ if (!prueth->registered_netdevs[i])
+ continue;
+ phy_stop(prueth->emac[i]->ndev->phydev);
+ phy_disconnect(prueth->emac[i]->ndev->phydev);
+ prueth->emac[i]->ndev->phydev = NULL;
+ unregister_netdev(prueth->registered_netdevs[i]);
+ }
+
+ for (i = 0; i < PRUETH_NUM_MACS; i++) {
+ eth_node = prueth->eth_node[i];
+ if (!eth_node)
+ continue;
+
+ prueth_netdev_exit(prueth, eth_node);
+ }
+
+ gen_pool_free(prueth->sram_pool,
+ (unsigned long)prueth->msmcram.va,
+ MSMC_RAM_SIZE);
+
+ pruss_release_mem_region(prueth->pruss, &prueth->shram);
+
+ pruss_put(prueth->pruss);
+
+ if (prueth->eth_node[PRUETH_MAC1])
+ prueth_put_cores(prueth, ICSS_SLICE1);
+
+ if (prueth->eth_node[PRUETH_MAC0])
+ prueth_put_cores(prueth, ICSS_SLICE0);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int prueth_suspend(struct device *dev)
+{
+ struct prueth *prueth = dev_get_drvdata(dev);
+ struct net_device *ndev;
+ int i, ret;
+
+ for (i = 0; i < PRUETH_NUM_MACS; i++) {
+ ndev = prueth->registered_netdevs[i];
+
+ if (!ndev)
+ continue;
+
+ if (netif_running(ndev)) {
+ netif_device_detach(ndev);
+ ret = emac_ndo_stop(ndev);
+ if (ret < 0) {
+ netdev_err(ndev, "failed to stop: %d", ret);
+ return ret;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int prueth_resume(struct device *dev)
+{
+ struct prueth *prueth = dev_get_drvdata(dev);
+ struct net_device *ndev;
+ int i, ret;
+
+ for (i = 0; i < PRUETH_NUM_MACS; i++) {
+ ndev = prueth->registered_netdevs[i];
+
+ if (!ndev)
+ continue;
+
+ if (netif_running(ndev)) {
+ ret = emac_ndo_open(ndev);
+ if (ret < 0) {
+ netdev_err(ndev, "failed to start: %d", ret);
+ return ret;
+ }
+ netif_device_attach(ndev);
+ }
+ }
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static const struct dev_pm_ops prueth_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(prueth_suspend, prueth_resume)
+};
+
+static const struct prueth_pdata am654_icssg_pdata = {
+ .fdqring_mode = K3_RINGACC_RING_MODE_MESSAGE,
+ .quirk_10m_link_issue = 1,
+};
+
+static const struct of_device_id prueth_dt_match[] = {
+ { .compatible = "ti,am654-icssg-prueth", .data = &am654_icssg_pdata },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, prueth_dt_match);
+
+static struct platform_driver prueth_driver = {
+ .probe = prueth_probe,
+ .remove = prueth_remove,
+ .driver = {
+ .name = "icssg-prueth",
+ .of_match_table = prueth_dt_match,
+ .pm = &prueth_dev_pm_ops,
+ },
+};
+module_platform_driver(prueth_driver);
+
+MODULE_AUTHOR("Roger Quadros <rogerq@ti.com>");
+MODULE_AUTHOR("Puranjay Mohan <p-mohan@ti.com>");
+MODULE_AUTHOR("Md Danish Anwar <danishanwar@ti.com>");
+MODULE_DESCRIPTION("PRUSS ICSSG Ethernet Driver");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,248 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#ifndef __NET_TI_ICSSG_PRUETH_H
+#define __NET_TI_ICSSG_PRUETH_H
+
+#include <linux/etherdevice.h>
+#include <linux/genalloc.h>
+#include <linux/if_vlan.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/net_tstamp.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_mdio.h>
+#include <linux/of_net.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/remoteproc/pruss.h>
+#include <linux/pruss_driver.h>
+#include <linux/ptp_clock_kernel.h>
+#include <linux/remoteproc.h>
+
+#include <linux/dma-mapping.h>
+#include <linux/dma/ti-cppi5.h>
+#include <linux/dma/k3-udma-glue.h>
+
+#include <net/devlink.h>
+
+#include "icssg_config.h"
+#include "icssg_switch_map.h"
+
+#define ICSS_SLICE0 0
+#define ICSS_SLICE1 1
+
+#define ICSS_FW_PRU 0
+#define ICSS_FW_RTU 1
+
+#define ICSSG_MAX_RFLOWS 8 /* per slice */
+
+/* Firmware status codes */
+#define ICSS_HS_FW_READY 0x55555555
+#define ICSS_HS_FW_DEAD 0xDEAD0000 /* lower 16 bits contain error code */
+
+/* Firmware command codes */
+#define ICSS_HS_CMD_BUSY 0x40000000
+#define ICSS_HS_CMD_DONE 0x80000000
+#define ICSS_HS_CMD_CANCEL 0x10000000
+
+/* Firmware commands */
+#define ICSS_CMD_SPAD 0x20
+#define ICSS_CMD_RXTX 0x10
+#define ICSS_CMD_ADD_FDB 0x1
+#define ICSS_CMD_DEL_FDB 0x2
+#define ICSS_CMD_SET_RUN 0x4
+#define ICSS_CMD_GET_FDB_SLOT 0x5
+#define ICSS_CMD_ENABLE_VLAN 0x5
+#define ICSS_CMD_DISABLE_VLAN 0x6
+#define ICSS_CMD_ADD_FILTER 0x7
+#define ICSS_CMD_ADD_MAC 0x8
+
+/* In switch mode there are 3 real ports i.e. 3 mac addrs.
+ * however Linux sees only the host side port. The other 2 ports
+ * are the switch ports.
+ * In emac mode there are 2 real ports i.e. 2 mac addrs.
+ * Linux sees both the ports.
+ */
+enum prueth_port {
+ PRUETH_PORT_HOST = 0, /* host side port */
+ PRUETH_PORT_MII0, /* physical port RG/SG MII 0 */
+ PRUETH_PORT_MII1, /* physical port RG/SG MII 1 */
+};
+
+enum prueth_mac {
+ PRUETH_MAC0 = 0,
+ PRUETH_MAC1,
+ PRUETH_NUM_MACS,
+};
+
+struct prueth_tx_chn {
+ struct device *dma_dev;
+ struct napi_struct napi_tx;
+ struct k3_cppi_desc_pool *desc_pool;
+ struct k3_udma_glue_tx_channel *tx_chn;
+ struct prueth_emac *emac;
+ u32 id;
+ u32 descs_num;
+ unsigned int irq;
+ char name[32];
+};
+
+struct prueth_rx_chn {
+ struct device *dev;
+ struct device *dma_dev;
+ struct k3_cppi_desc_pool *desc_pool;
+ struct k3_udma_glue_rx_channel *rx_chn;
+ u32 descs_num;
+ unsigned int irq[ICSSG_MAX_RFLOWS]; /* separate irq per flow */
+ char name[32];
+};
+
+/* There are 4 Tx DMA channels, but the highest priority is CH3 (thread 3)
+ * and lower three are lower priority channels or threads.
+ */
+#define PRUETH_MAX_TX_QUEUES 4
+
+/* data for each emac port */
+struct prueth_emac {
+ bool fw_running;
+ struct prueth *prueth;
+ struct net_device *ndev;
+ u8 mac_addr[6];
+ struct napi_struct napi_rx;
+ u32 msg_enable;
+
+ int link;
+ int speed;
+ int duplex;
+
+ const char *phy_id;
+ struct device_node *phy_node;
+ phy_interface_t phy_if;
+ enum prueth_port port_id;
+
+ /* DMA related */
+ struct prueth_tx_chn tx_chns[PRUETH_MAX_TX_QUEUES];
+ struct completion tdown_complete;
+ atomic_t tdown_cnt;
+ struct prueth_rx_chn rx_chns;
+ int rx_flow_id_base;
+ int tx_ch_num;
+
+ spinlock_t lock; /* serialize access */
+
+ unsigned long state;
+ struct completion cmd_complete;
+ /* Mutex to serialize access to firmware command interface */
+ struct mutex cmd_lock;
+ struct work_struct rx_mode_work;
+ struct workqueue_struct *cmd_wq;
+
+ struct pruss_mem_region dram;
+};
+
+/**
+ * struct prueth_pdata - PRUeth platform data
+ * @fdqring_mode: Free desc queue mode
+ * @quirk_10m_link_issue: 10M link detect errata
+ */
+struct prueth_pdata {
+ enum k3_ring_mode fdqring_mode;
+ u32 quirk_10m_link_issue:1;
+};
+
+/**
+ * struct prueth - PRUeth structure
+ * @dev: device
+ * @pruss: pruss handle
+ * @pru: rproc instances of PRUs
+ * @rtu: rproc instances of RTUs
+ * @txpru: rproc instances of TX_PRUs
+ * @shram: PRUSS shared RAM region
+ * @sram_pool: MSMC RAM pool for buffers
+ * @msmcram: MSMC RAM region
+ * @eth_node: DT node for the port
+ * @emac: private EMAC data structure
+ * @registered_netdevs: list of registered netdevs
+ * @fw_data: firmware names to be used with PRU remoteprocs
+ * @config: firmware load time configuration per slice
+ * @miig_rt: regmap to mii_g_rt block
+ * @mii_rt: regmap to mii_rt block
+ * @pa_stats: regmap to pa_stats block
+ * @pru_id: ID for each of the PRUs
+ * @pdev: pointer to ICSSG platform device
+ * @pdata: pointer to platform data for ICSSG driver
+ * @icssg_hwcmdseq: seq counter or HWQ messages
+ * @emacs_initialized: num of EMACs/ext ports that are up/running
+ */
+struct prueth {
+ struct device *dev;
+ struct pruss *pruss;
+ struct rproc *pru[PRUSS_NUM_PRUS];
+ struct rproc *rtu[PRUSS_NUM_PRUS];
+ struct rproc *txpru[PRUSS_NUM_PRUS];
+ struct pruss_mem_region shram;
+ struct gen_pool *sram_pool;
+ struct pruss_mem_region msmcram;
+
+ struct device_node *eth_node[PRUETH_NUM_MACS];
+ struct prueth_emac *emac[PRUETH_NUM_MACS];
+ struct net_device *registered_netdevs[PRUETH_NUM_MACS];
+ const struct prueth_private_data *fw_data;
+ struct regmap *miig_rt;
+ struct regmap *mii_rt;
+ struct regmap *pa_stats;
+
+ enum pruss_pru_id pru_id[PRUSS_NUM_PRUS];
+ struct platform_device *pdev;
+ struct prueth_pdata pdata;
+ u8 icssg_hwcmdseq;
+
+ int emacs_initialized;
+};
+
+/* Classifier helpers */
+void icssg_class_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac);
+void icssg_class_set_host_mac_addr(struct regmap *miig_rt, const u8 *mac);
+void icssg_class_disable(struct regmap *miig_rt, int slice);
+void icssg_class_default(struct regmap *miig_rt, int slice, bool allmulti);
+void icssg_ft1_set_mac_addr(struct regmap *miig_rt, int slice, u8 *mac_addr);
+
+/* Buffer queue helpers */
+int icssg_queue_pop(struct prueth *prueth, u8 queue);
+void icssg_queue_push(struct prueth *prueth, int queue, u16 addr);
+u32 icssg_queue_level(struct prueth *prueth, int queue);
+
+/* get PRUSS SLICE number from prueth_emac */
+static inline int prueth_emac_slice(struct prueth_emac *emac)
+{
+ switch (emac->port_id) {
+ case PRUETH_PORT_MII0:
+ return ICSS_SLICE0;
+ case PRUETH_PORT_MII1:
+ return ICSS_SLICE1;
+ default:
+ return -EINVAL;
+ }
+}
+
+/* config helpers */
+void icssg_config_ipg(struct prueth_emac *emac);
+int icssg_config(struct prueth *prueth, struct prueth_emac *emac,
+ int slice);
+int emac_set_port_state(struct prueth_emac *emac,
+ enum icssg_port_state_cmd state);
+void icssg_config_set_speed(struct prueth_emac *emac);
+
+#define prueth_napi_to_tx_chn(pnapi) \
+ container_of(pnapi, struct prueth_tx_chn, napi_tx)
+
+#endif /* __NET_TI_ICSSG_PRUETH_H */
new file mode 100644
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0
+/* ICSSG Buffer queue helpers
+ *
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com
+ */
+
+#include <linux/regmap.h>
+#include "icssg_prueth.h"
+
+#define ICSSG_QUEUES_MAX 64
+#define ICSSG_QUEUE_OFFSET 0xd00
+#define ICSSG_QUEUE_PEEK_OFFSET 0xe00
+#define ICSSG_QUEUE_CNT_OFFSET 0xe40
+#define ICSSG_QUEUE_RESET_OFFSET 0xf40
+
+int icssg_queue_pop(struct prueth *prueth, u8 queue)
+{
+ u32 val, cnt;
+
+ if (queue >= ICSSG_QUEUES_MAX)
+ return -EINVAL;
+
+ regmap_read(prueth->miig_rt, ICSSG_QUEUE_CNT_OFFSET + 4 * queue, &cnt);
+ if (!cnt)
+ return -EINVAL;
+
+ regmap_read(prueth->miig_rt, ICSSG_QUEUE_OFFSET + 4 * queue, &val);
+
+ return val;
+}
+
+void icssg_queue_push(struct prueth *prueth, int queue, u16 addr)
+{
+ if (queue >= ICSSG_QUEUES_MAX)
+ return;
+
+ regmap_write(prueth->miig_rt, ICSSG_QUEUE_OFFSET + 4 * queue, addr);
+}
new file mode 100644
@@ -0,0 +1,234 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Texas Instruments ICSSG Ethernet driver
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#ifndef __NET_TI_ICSSG_SWITCH_MAP_H
+#define __NET_TI_ICSSG_SWITCH_MAP_H
+
+/************************* Ethernet Switch Constants *********************/
+
+/* if bucket size is changed in firmware then this too should be changed
+ * because it directly impacts FDB ageing calculation
+ */
+#define NUMBER_OF_FDB_BUCKET_ENTRIES (4)
+
+/* This is fixed in ICSSG */
+#define SIZE_OF_FDB (2048)
+
+#define FW_LINK_SPEED_1G (0x00)
+#define FW_LINK_SPEED_100M (0x01)
+#define FW_LINK_SPEED_10M (0x02)
+#define FW_LINK_SPEED_HD (0x80)
+
+/* Time after which FDB entries are checked for aged out values.
+ * Values are in nanoseconds
+ */
+#define FDB_AGEING_TIMEOUT_OFFSET 0x0014
+
+/* Default VLAN tag for Host Port */
+#define HOST_PORT_DF_VLAN_OFFSET 0x001C
+
+/* Same as HOST_PORT_DF_VLAN_OFFSET */
+#define EMAC_ICSSG_SWITCH_PORT0_DEFAULT_VLAN_OFFSET HOST_PORT_DF_VLAN_OFFSET
+
+/* Default VLAN tag for P1 Port */
+#define P1_PORT_DF_VLAN_OFFSET 0x0020
+
+/* Same as P1_PORT_DF_VLAN_OFFSET */
+#define EMAC_ICSSG_SWITCH_PORT1_DEFAULT_VLAN_OFFSET P1_PORT_DF_VLAN_OFFSET
+
+/* default VLAN tag for P2 Port */
+#define P2_PORT_DF_VLAN_OFFSET 0x0024
+
+/* Same as P2_PORT_DF_VLAN_OFFSET */
+#define EMAC_ICSSG_SWITCH_PORT2_DEFAULT_VLAN_OFFSET P2_PORT_DF_VLAN_OFFSET
+
+/* VLAN-FID Table offset. 4096 VIDs. 2B per VID = 8KB = 0x2000 */
+#define VLAN_STATIC_REG_TABLE_OFFSET 0x0100
+
+/* VLAN-FID Table offset for EMAC */
+#define EMAC_ICSSG_SWITCH_DEFAULT_VLAN_TABLE_OFFSET VLAN_STATIC_REG_TABLE_OFFSET
+
+/* Packet descriptor Q reserved memory */
+#define PORT_DESC0_HI 0x2104
+
+/* Packet descriptor Q reserved memory */
+#define PORT_DESC0_LO 0x2F6C
+
+/* Packet descriptor Q reserved memory */
+#define PORT_DESC1_HI 0x3DD4
+
+/* Packet descriptor Q reserved memory */
+#define PORT_DESC1_LO 0x4C3C
+
+/* Packet descriptor Q reserved memory */
+#define HOST_DESC0_HI 0x5AA4
+
+/* Packet descriptor Q reserved memory */
+#define HOST_DESC0_LO 0x5F0C
+
+/* Packet descriptor Q reserved memory */
+#define HOST_DESC1_HI 0x6374
+
+/* Packet descriptor Q reserved memory */
+#define HOST_DESC1_LO 0x67DC
+
+/* Special packet descriptor Q reserved memory */
+#define HOST_SPPD0 0x7AAC
+
+/* Special acket descriptor Q reserved memory */
+#define HOST_SPPD1 0x7EAC
+
+/* _Small_Description_ */
+#define TIMESYNC_FW_WC_CYCLECOUNT_OFFSET 0x83EC
+
+/* IEP count hi roll over count */
+#define TIMESYNC_FW_WC_HI_ROLLOVER_COUNT_OFFSET 0x83F4
+
+/* _Small_Description_ */
+#define TIMESYNC_FW_WC_COUNT_HI_SW_OFFSET_OFFSET 0x83F8
+
+/* Set clock descriptor */
+#define TIMESYNC_FW_WC_SETCLOCK_DESC_OFFSET 0x83FC
+
+/* _Small_Description_ */
+#define TIMESYNC_FW_WC_SYNCOUT_REDUCTION_FACTOR_OFFSET 0x843C
+
+/* _Small_Description_ */
+#define TIMESYNC_FW_WC_SYNCOUT_REDUCTION_COUNT_OFFSET 0x8440
+
+/* _Small_Description_ */
+#define TIMESYNC_FW_WC_SYNCOUT_START_TIME_CYCLECOUNT_OFFSET 0x8444
+
+/* Control variable to generate SYNC1 */
+#define TIMESYNC_FW_WC_ISOM_PIN_SIGNAL_EN_OFFSET 0x844C
+
+/* SystemTime Sync0 periodicity */
+#define TIMESYNC_FW_ST_SYNCOUT_PERIOD_OFFSET 0x8450
+
+/* pktTxDelay for P1 = link speed dependent p1 mac delay + p1 phy delay */
+#define TIMESYNC_FW_WC_PKTTXDELAY_P1_OFFSET 0x8454
+
+/* pktTxDelay for P2 = link speed dependent p2 mac delay + p2 phy delay */
+#define TIMESYNC_FW_WC_PKTTXDELAY_P2_OFFSET 0x8458
+
+/* Set clock operation done signal for next task */
+#define TIMESYNC_FW_SIG_PNFW_OFFSET 0x845C
+
+/* Set clock operation done signal for next task */
+#define TIMESYNC_FW_SIG_TIMESYNCFW_OFFSET 0x8460
+
+/* New list is copied at this time */
+#define TAS_CONFIG_CHANGE_TIME 0x000C
+
+/* config change error counter */
+#define TAS_CONFIG_CHANGE_ERROR_COUNTER 0x0014
+
+/* TAS List update pending flag */
+#define TAS_CONFIG_PENDING 0x0018
+
+/* TAS list update trigger flag */
+#define TAS_CONFIG_CHANGE 0x0019
+
+/* List length for new TAS schedule */
+#define TAS_ADMIN_LIST_LENGTH 0x001A
+
+/* Currently active TAS list index */
+#define TAS_ACTIVE_LIST_INDEX 0x001B
+
+/* Cycle time for the new TAS schedule */
+#define TAS_ADMIN_CYCLE_TIME 0x001C
+
+/* Cycle counts remaining till the TAS list update */
+#define TAS_CONFIG_CHANGE_CYCLE_COUNT 0x0020
+
+/* Base Flow ID for sending Packets to Host for Slice0 */
+#define PSI_L_REGULAR_FLOW_ID_BASE_OFFSET 0x0024
+
+/* Same as PSI_L_REGULAR_FLOW_ID_BASE_OFFSET */
+#define EMAC_ICSSG_SWITCH_PSI_L_REGULAR_FLOW_ID_BASE_OFFSET PSI_L_REGULAR_FLOW_ID_BASE_OFFSET
+
+/* Base Flow ID for sending mgmt and Tx TS to Host for Slice0 */
+#define PSI_L_MGMT_FLOW_ID_OFFSET 0x0026
+
+/* Same as PSI_L_MGMT_FLOW_ID_OFFSET */
+#define EMAC_ICSSG_SWITCH_PSI_L_MGMT_FLOW_ID_BASE_OFFSET PSI_L_MGMT_FLOW_ID_OFFSET
+
+/* Queue number for Special Packets written here */
+#define SPL_PKT_DEFAULT_PRIORITY 0x0028
+
+/* Express Preemptible Queue Mask */
+#define EXPRESS_PRE_EMPTIVE_Q_MASK 0x0029
+
+/* Port1/Port2 Default Queue number for untagged Packets, only 1B is used */
+#define QUEUE_NUM_UNTAGGED 0x002A
+
+/* Stores the table used for priority regeneration. 1B per PCP/Queue */
+#define PORT_Q_PRIORITY_REGEN_OFFSET 0x002C
+
+/* For marking Packet as priority/express (this feature is disabled) or
+ * cut-through/S&F.
+ */
+#define EXPRESS_PRE_EMPTIVE_Q_MAP 0x0034
+
+/* Stores the table used for priority mapping. 1B per PCP/Queue */
+#define PORT_Q_PRIORITY_MAPPING_OFFSET 0x003C
+
+/* Used to notify the FW of the current link speed */
+#define PORT_LINK_SPEED_OFFSET 0x00A8
+
+/* TAS gate mask for windows list0 */
+#define TAS_GATE_MASK_LIST0 0x0100
+
+/* TAS gate mask for windows list1 */
+#define TAS_GATE_MASK_LIST1 0x0350
+
+/* Memory to Enable/Disable Preemption on TX side */
+#define PRE_EMPTION_ENABLE_TX 0x05A0
+
+/* Active State of Preemption on TX side */
+#define PRE_EMPTION_ACTIVE_TX 0x05A1
+
+/* Memory to Enable/Disable Verify State Machine Preemption */
+#define PRE_EMPTION_ENABLE_VERIFY 0x05A2
+
+/* Verify Status of State Machine */
+#define PRE_EMPTION_VERIFY_STATUS 0x05A3
+
+/* Non Final Fragment Size supported by Link Partner */
+#define PRE_EMPTION_ADD_FRAG_SIZE_REMOTE 0x05A4
+
+/* Non Final Fragment Size supported by Firmware */
+#define PRE_EMPTION_ADD_FRAG_SIZE_LOCAL 0x05A6
+
+/* Time in ms the State machine waits for respond Packet */
+#define PRE_EMPTION_VERIFY_TIME 0x05A8
+
+/* Memory used for R30 related management commands */
+#define MGR_R30_CMD_OFFSET 0x05AC
+
+/* HW Buffer Pool0 base address */
+#define BUFFER_POOL_0_ADDR_OFFSET 0x05BC
+
+/* 16B for Host Egress MSMC Q (Pre-emptible) context */
+#define HOST_RX_Q_PRE_CONTEXT_OFFSET 0x0684
+
+/* Buffer for 8 FDB entries to be added by 'Add Multiple FDB entries IOCTL' */
+#define FDB_CMD_BUFFER 0x0894
+
+/* TAS queue max sdu length list */
+#define TAS_QUEUE_MAX_SDU_LIST 0x08FA
+
+/* Used by FW to generate random number with the SEED value */
+#define HD_RAND_SEED_OFFSET 0x0934
+
+/* 16B for Host Egress MSMC Q (Express) context */
+#define HOST_RX_Q_EXP_CONTEXT_OFFSET 0x0940
+
+/* Start of 32 bits PA_STAT counters */
+#define PA_STAT_32b_START_OFFSET 0x0080
+
+#endif /* __NET_TI_ICSSG_SWITCH_MAP_H */