| Message ID | 20230807155026.28671-1-quic_nitirawa@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [V1] scsi: ufs: qcom: Align programming sequence as per HW spec | expand |
On 8/7/2023 8:50 AM, Nitin Rawat wrote: > Align clock configuration as per Qualcomm UFS controller > hardware specification. > > This change updates UFS_SYS1CLK_1US, CORE_CLK_1US_CYCLES, > PA_VS_CORE_CLK_40NS_CYCLES timer configuration for Qunipro > and UTP to align with Qualcomm UFS HW specification. > > Co-developed-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com> > Signed-off-by: Naveen Kumar Goud Arepalli <quic_narepall@quicinc.com> > Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> > --- > drivers/ufs/host/ufs-qcom.c | 262 +++++++++++++++++++++++++++--------- > drivers/ufs/host/ufs-qcom.h | 20 ++- > 2 files changed, 215 insertions(+), 67 deletions(-) > > diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c > index e7164ce7336b..836894c112c1 100644 > --- a/drivers/ufs/host/ufs-qcom.c > +++ b/drivers/ufs/host/ufs-qcom.c > @@ -91,10 +91,7 @@ struct __ufs_qcom_bw_table { > }; > > static struct ufs_qcom_host *ufs_qcom_hosts[MAX_UFS_QCOM_HOSTS]; > - > static void ufs_qcom_get_default_testbus_cfg(struct ufs_qcom_host *host); > -static int ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(struct ufs_hba *hba, > - u32 clk_cycles); > > static struct ufs_qcom_host *rcdev_to_ufs_host(struct reset_controller_dev *rcd) > { > @@ -531,8 +528,9 @@ static int ufs_qcom_hce_enable_notify(struct ufs_hba *hba, > /* > * Return: zero for success and non-zero in case of a failure. > */ > -static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, > - u32 hs, u32 rate, bool update_link_startup_timer) > +static int __ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, > + u32 hs, u32 rate, bool link_startup, > + bool is_pre_scale_up) > { > struct ufs_qcom_host *host = ufshcd_get_variant(hba); > struct ufs_clk_info *clki; > @@ -563,11 +561,16 @@ static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, > /* > * The Qunipro controller does not use following registers: > * SYS1CLK_1US_REG, TX_SYMBOL_CLK_1US_REG, CLK_NS_REG & > - * UFS_REG_PA_LINK_STARTUP_TIMER > - * But UTP controller uses SYS1CLK_1US_REG register for Interrupt > - * Aggregation logic. > - */ > - if (ufs_qcom_cap_qunipro(host) && !ufshcd_is_intr_aggr_allowed(hba)) > + * UFS_REG_PA_LINK_STARTUP_TIMER. > + * However UTP controller uses SYS1CLK_1US_REG register for Interrupt > + * Aggregation logic and Auto hibern8 logic. > + * It is mandatory to write SYS1CLK_1US_REG register on UFS host > + * controller V4.0.0 onwards. > + */ > + if (ufs_qcom_cap_qunipro(host) && > + !(ufshcd_is_intr_aggr_allowed(hba) || > + ufshcd_is_auto_hibern8_supported(hba) || > + host->hw_ver.major >= 4)) > return 0; > > if (gear == 0) { > @@ -576,8 +579,14 @@ static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, > } > > list_for_each_entry(clki, &hba->clk_list_head, list) { > - if (!strcmp(clki->name, "core_clk")) > - core_clk_rate = clk_get_rate(clki->clk); > + if (!strcmp(clki->name, "core_clk")) { > + if (is_pre_scale_up) > + core_clk_rate = clki->max_freq; > + else > + core_clk_rate = clk_get_rate(clki->clk); > + break; > + } > + > } > > /* If frequency is smaller than 1MHz, set to 1MHz */ > @@ -657,7 +666,7 @@ static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, > mb(); > } > > - if (update_link_startup_timer && host->hw_ver.major != 0x5) { > + if (link_startup && host->hw_ver.major != 0x5) { > ufshcd_writel(hba, ((core_clk_rate / MSEC_PER_SEC) * 100), > REG_UFS_CFG0); > /* > @@ -670,6 +679,114 @@ static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, > return 0; > } > > +static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, > + u32 hs, u32 rate, bool link_startup) Hi Nitin, How about adding scale_up param to this function ufs_qcom_cfg_timers() as below: static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, u32 hs, u32 rate, bool link_startup, bool scale_up) Then replace all references to __ufs_qcom_cfg_timers() with ufs_qcom_cfg_timers()? It is hard to follow these two almost identical functions with 2 flags invoked from different places, so try to get rid of one. > +{ > + return __ufs_qcom_cfg_timers(hba, gear, hs, rate, > + link_startup, false); > +} > + > +static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba, > + u32 clk_1us_cycles, > + u32 clk_40ns_cycles, > + bool scale_up) > +{ > + struct ufs_qcom_host *host = ufshcd_get_variant(hba); > + u32 mask = MAX_CORE_CLK_1US_CYCLES_MASK; > + u32 reg, clk_cycles; Remove the clk_cycles variable and re-use the variable reg? > + u32 offset = 0; > + int err; > + > + /* Bit mask and offset changed on UFS host controller V4.0.0 onwards */ > + if (host->hw_ver.major >= 4) { > + mask = MAX_CORE_CLK_1US_CYCLES_MASK_V4; > + offset = MAX_CORE_CLK_1US_CYCLES_OFFSET_V4; > + } > + > + if (clk_1us_cycles > mask) > + return -EINVAL; > + > + err = ufshcd_dme_get(hba, UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), ®); > + if (err) > + return err; > + > + reg &= ~(mask << offset); > + reg |= clk_1us_cycles << offset; > + > + if (scale_up) > + reg |= CORE_CLK_DIV_EN_BIT; > + else > + reg &= ~CORE_CLK_DIV_EN_BIT; > + > + err = ufshcd_dme_set(hba, UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), reg); > + if (err) > + return err; > + > + /* > + * UFS host controller V4.0.0 onwards needs to program > + * PA_VS_CORE_CLK_40NS_CYCLES attribute per programmed > + * frequency of unipro core clk of UFS host controller. > + */ > + if (host->hw_ver.major >= 4) { > + if (clk_40ns_cycles > PA_VS_CORE_CLK_40NS_CYCLES_MASK) > + return -EINVAL; > + > + err = ufshcd_dme_get(hba, Nitpicking..You can probably fit all 3 params on 1 line once you replace clk_cycles with reg. > + UIC_ARG_MIB(PA_VS_CORE_CLK_40NS_CYCLES), > + &clk_cycles); > + if (err) > + return err; > + > + clk_cycles &= ~PA_VS_CORE_CLK_40NS_CYCLES_MASK; > + clk_cycles |= clk_40ns_cycles; > + > + err = ufshcd_dme_set(hba, Same comment as above. > + UIC_ARG_MIB(PA_VS_CORE_CLK_40NS_CYCLES), > + clk_cycles); > + } > + > + return err; > +} > + > +static int ufs_qcom_cfg_core_clk_ctrl(struct ufs_hba *hba) > +{ > + struct list_head *head = &hba->clk_list_head; > + struct ufs_clk_info *clki; > + u32 max_freq = 0; > + int err; > + > + list_for_each_entry(clki, head, list) { > + if (!IS_ERR_OR_NULL(clki->clk) && > + (!strcmp(clki->name, "core_clk_unipro"))) { > + max_freq = clki->max_freq; > + break; > + } > + } > + > + switch (max_freq) { > + case MHZ_403: > + err = ufs_qcom_set_core_clk_ctrl(hba, 403, 16, true); > + break; > + case MHZ_300: > + err = ufs_qcom_set_core_clk_ctrl(hba, 300, 12, true); > + break; > + case MHZ_201_5: > + err = ufs_qcom_set_core_clk_ctrl(hba, 202, 8, true); > + break; > + case MHZ_150: > + err = ufs_qcom_set_core_clk_ctrl(hba, 150, 6, true); > + break; > + case MHZ_100: > + err = ufs_qcom_set_core_clk_ctrl(hba, 100, 4, true); > + break; > + default: > + dev_err(hba->dev, "unipro max_freq=%u entry missing\n", max_freq); > + err = -EINVAL; > + break; > + } > + > + return err; > +} > static int ufs_qcom_link_startup_notify(struct ufs_hba *hba, > enum ufs_notify_change_status status) > { > @@ -685,13 +802,15 @@ static int ufs_qcom_link_startup_notify(struct ufs_hba *hba, > return -EINVAL; > } > > - if (ufs_qcom_cap_qunipro(host)) > - /* > - * set unipro core clock cycles to 150 & clear clock > - * divider > - */ > - err = ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(hba, > - 150); > + if (ufs_qcom_cap_qunipro(host)) { > + err = ufs_qcom_cfg_core_clk_ctrl(hba); > + if (err) { > + dev_err(hba->dev, > + "%s cfg core clk ctrl failed\n", > + __func__); > + return err; > + } > + } > > /* > * Some UFS devices (and may be host) have issues if LCC is > @@ -1296,69 +1415,52 @@ static void ufs_qcom_exit(struct ufs_hba *hba) > phy_exit(host->generic_phy); > } > > -static int ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(struct ufs_hba *hba, > - u32 clk_cycles) > +static int ufs_qcom_clk_scale_up_pre_change(struct ufs_hba *hba) > { > - int err; > - u32 core_clk_ctrl_reg; > - > - if (clk_cycles > DME_VS_CORE_CLK_CTRL_MAX_CORE_CLK_1US_CYCLES_MASK) > - return -EINVAL; > - > - err = ufshcd_dme_get(hba, > - UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), > - &core_clk_ctrl_reg); > - if (err) > - return err; > - > - core_clk_ctrl_reg &= ~DME_VS_CORE_CLK_CTRL_MAX_CORE_CLK_1US_CYCLES_MASK; > - core_clk_ctrl_reg |= clk_cycles; > - > - /* Clear CORE_CLK_DIV_EN */ > - core_clk_ctrl_reg &= ~DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT; > + struct ufs_qcom_host *host = ufshcd_get_variant(hba); > + struct ufs_pa_layer_attr *attr = &host->dev_req_params; > + int err = 0; > > - return ufshcd_dme_set(hba, > - UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), > - core_clk_ctrl_reg); > -} > + if (!ufs_qcom_cap_qunipro(host)) > + goto out; > > -static int ufs_qcom_clk_scale_up_pre_change(struct ufs_hba *hba) > -{ > - /* nothing to do as of now */ > - return 0; > + if (attr) { > + err = __ufs_qcom_cfg_timers(hba, attr->gear_rx, > + attr->pwr_rx, attr->hs_rate, > + false, true); > + if (err) > + dev_err(hba->dev, "%s ufs cfg timer failed\n", > + __func__); > + } > + err = ufs_qcom_cfg_core_clk_ctrl(hba); > +out: > + return err; > } > > static int ufs_qcom_clk_scale_up_post_change(struct ufs_hba *hba) > { > - struct ufs_qcom_host *host = ufshcd_get_variant(hba); > - > - if (!ufs_qcom_cap_qunipro(host)) > - return 0; > - > - /* set unipro core clock cycles to 150 and clear clock divider */ > - return ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(hba, 150); > + return 0; > } > > static int ufs_qcom_clk_scale_down_pre_change(struct ufs_hba *hba) > { > struct ufs_qcom_host *host = ufshcd_get_variant(hba); > int err; > - u32 core_clk_ctrl_reg; > + u32 reg; > > if (!ufs_qcom_cap_qunipro(host)) > return 0; > > - err = ufshcd_dme_get(hba, > - UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), > - &core_clk_ctrl_reg); > + err = ufshcd_dme_get(hba, UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), ®); > + if (err) > + return err; > > /* make sure CORE_CLK_DIV_EN is cleared */ > - if (!err && > - (core_clk_ctrl_reg & DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT)) { > - core_clk_ctrl_reg &= ~DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT; > + if (reg & CORE_CLK_DIV_EN_BIT) { > + reg &= ~CORE_CLK_DIV_EN_BIT; > err = ufshcd_dme_set(hba, > UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), > - core_clk_ctrl_reg); > + reg); > } > > return err; > @@ -1367,12 +1469,44 @@ static int ufs_qcom_clk_scale_down_pre_change(struct ufs_hba *hba) > static int ufs_qcom_clk_scale_down_post_change(struct ufs_hba *hba) > { > struct ufs_qcom_host *host = ufshcd_get_variant(hba); > + struct ufs_pa_layer_attr *attr = &host->dev_req_params; > + struct list_head *head = &hba->clk_list_head; > + struct ufs_clk_info *clki; > + u32 curr_freq = 0; > + int err; > > if (!ufs_qcom_cap_qunipro(host)) > return 0; > > - /* set unipro core clock cycles to 75 and clear clock divider */ > - return ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(hba, 75); > + if (attr) > + ufs_qcom_cfg_timers(hba, attr->gear_rx, attr->pwr_rx, > + attr->hs_rate, false); > + > + list_for_each_entry(clki, head, list) { > + if (!IS_ERR_OR_NULL(clki->clk) && > + (!strcmp(clki->name, "core_clk_unipro"))) { > + curr_freq = clk_get_rate(clki->clk); > + break; > + } > + } > + > + switch (curr_freq) { > + case MHZ_37_5: > + err = ufs_qcom_set_core_clk_ctrl(hba, 38, 2, false); > + break; > + case MHZ_75: > + err = ufs_qcom_set_core_clk_ctrl(hba, 75, 3, false); > + break; > + case MHZ_100: > + err = ufs_qcom_set_core_clk_ctrl(hba, 100, 4, false); > + break; > + default: > + err = -EINVAL; > + dev_err(hba->dev, "unipro curr_freq=%u entry missing\n", curr_freq); > + break; > + } > + > + return err; > } > > static int ufs_qcom_clk_scale_notify(struct ufs_hba *hba, > diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h > index d6f8e74bd538..da7b5ee7c1cf 100644 > --- a/drivers/ufs/host/ufs-qcom.h > +++ b/drivers/ufs/host/ufs-qcom.h > @@ -79,6 +79,17 @@ enum { > UFS_MEM_CQIS_VS = 0x8, > }; > > + > +/* QCOM UFS host controller core clk frequencies */ > +#define MHZ_37_5 37500000 > +#define MHZ_50 50000000 > +#define MHZ_75 75000000 > +#define MHZ_100 100000000 > +#define MHZ_150 150000000 > +#define MHZ_300 300000000 > +#define MHZ_201_5 201500000 > +#define MHZ_403 403000000 > + > #define UFS_CNTLR_2_x_x_VEN_REGS_OFFSET(x) (0x000 + x) > #define UFS_CNTLR_3_x_x_VEN_REGS_OFFSET(x) (0x400 + x) > > @@ -129,9 +140,12 @@ enum { > #define PA_VS_CONFIG_REG1 0x9000 > #define DME_VS_CORE_CLK_CTRL 0xD002 > /* bit and mask definitions for DME_VS_CORE_CLK_CTRL attribute */ > -#define DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT BIT(8) > -#define DME_VS_CORE_CLK_CTRL_MAX_CORE_CLK_1US_CYCLES_MASK 0xFF > - > +#define MAX_CORE_CLK_1US_CYCLES_MASK_V4 0xFFF > +#define MAX_CORE_CLK_1US_CYCLES_OFFSET_V4 0x10 > +#define MAX_CORE_CLK_1US_CYCLES_MASK 0xFF > +#define CORE_CLK_DIV_EN_BIT BIT(8) > +#define PA_VS_CORE_CLK_40NS_CYCLES 0x9007 > +#define PA_VS_CORE_CLK_40NS_CYCLES_MASK 0x3F Remove the 1 extra tab in between the macro names and their values? > static inline void > ufs_qcom_get_controller_revision(struct ufs_hba *hba, > u8 *major, u16 *minor, u16 *step) > -- > 2.17.1 >
diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c index e7164ce7336b..836894c112c1 100644 --- a/drivers/ufs/host/ufs-qcom.c +++ b/drivers/ufs/host/ufs-qcom.c @@ -91,10 +91,7 @@ struct __ufs_qcom_bw_table { }; static struct ufs_qcom_host *ufs_qcom_hosts[MAX_UFS_QCOM_HOSTS]; - static void ufs_qcom_get_default_testbus_cfg(struct ufs_qcom_host *host); -static int ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(struct ufs_hba *hba, - u32 clk_cycles); static struct ufs_qcom_host *rcdev_to_ufs_host(struct reset_controller_dev *rcd) { @@ -531,8 +528,9 @@ static int ufs_qcom_hce_enable_notify(struct ufs_hba *hba, /* * Return: zero for success and non-zero in case of a failure. */ -static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, - u32 hs, u32 rate, bool update_link_startup_timer) +static int __ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, + u32 hs, u32 rate, bool link_startup, + bool is_pre_scale_up) { struct ufs_qcom_host *host = ufshcd_get_variant(hba); struct ufs_clk_info *clki; @@ -563,11 +561,16 @@ static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, /* * The Qunipro controller does not use following registers: * SYS1CLK_1US_REG, TX_SYMBOL_CLK_1US_REG, CLK_NS_REG & - * UFS_REG_PA_LINK_STARTUP_TIMER - * But UTP controller uses SYS1CLK_1US_REG register for Interrupt - * Aggregation logic. - */ - if (ufs_qcom_cap_qunipro(host) && !ufshcd_is_intr_aggr_allowed(hba)) + * UFS_REG_PA_LINK_STARTUP_TIMER. + * However UTP controller uses SYS1CLK_1US_REG register for Interrupt + * Aggregation logic and Auto hibern8 logic. + * It is mandatory to write SYS1CLK_1US_REG register on UFS host + * controller V4.0.0 onwards. + */ + if (ufs_qcom_cap_qunipro(host) && + !(ufshcd_is_intr_aggr_allowed(hba) || + ufshcd_is_auto_hibern8_supported(hba) || + host->hw_ver.major >= 4)) return 0; if (gear == 0) { @@ -576,8 +579,14 @@ static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, } list_for_each_entry(clki, &hba->clk_list_head, list) { - if (!strcmp(clki->name, "core_clk")) - core_clk_rate = clk_get_rate(clki->clk); + if (!strcmp(clki->name, "core_clk")) { + if (is_pre_scale_up) + core_clk_rate = clki->max_freq; + else + core_clk_rate = clk_get_rate(clki->clk); + break; + } + } /* If frequency is smaller than 1MHz, set to 1MHz */ @@ -657,7 +666,7 @@ static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, mb(); } - if (update_link_startup_timer && host->hw_ver.major != 0x5) { + if (link_startup && host->hw_ver.major != 0x5) { ufshcd_writel(hba, ((core_clk_rate / MSEC_PER_SEC) * 100), REG_UFS_CFG0); /* @@ -670,6 +679,114 @@ static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, return 0; } +static int ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, + u32 hs, u32 rate, bool link_startup) +{ + return __ufs_qcom_cfg_timers(hba, gear, hs, rate, + link_startup, false); +} + +static int ufs_qcom_set_core_clk_ctrl(struct ufs_hba *hba, + u32 clk_1us_cycles, + u32 clk_40ns_cycles, + bool scale_up) +{ + struct ufs_qcom_host *host = ufshcd_get_variant(hba); + u32 mask = MAX_CORE_CLK_1US_CYCLES_MASK; + u32 reg, clk_cycles; + u32 offset = 0; + int err; + + /* Bit mask and offset changed on UFS host controller V4.0.0 onwards */ + if (host->hw_ver.major >= 4) { + mask = MAX_CORE_CLK_1US_CYCLES_MASK_V4; + offset = MAX_CORE_CLK_1US_CYCLES_OFFSET_V4; + } + + if (clk_1us_cycles > mask) + return -EINVAL; + + err = ufshcd_dme_get(hba, UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), ®); + if (err) + return err; + + reg &= ~(mask << offset); + reg |= clk_1us_cycles << offset; + + if (scale_up) + reg |= CORE_CLK_DIV_EN_BIT; + else + reg &= ~CORE_CLK_DIV_EN_BIT; + + err = ufshcd_dme_set(hba, UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), reg); + if (err) + return err; + + /* + * UFS host controller V4.0.0 onwards needs to program + * PA_VS_CORE_CLK_40NS_CYCLES attribute per programmed + * frequency of unipro core clk of UFS host controller. + */ + if (host->hw_ver.major >= 4) { + if (clk_40ns_cycles > PA_VS_CORE_CLK_40NS_CYCLES_MASK) + return -EINVAL; + + err = ufshcd_dme_get(hba, + UIC_ARG_MIB(PA_VS_CORE_CLK_40NS_CYCLES), + &clk_cycles); + if (err) + return err; + + clk_cycles &= ~PA_VS_CORE_CLK_40NS_CYCLES_MASK; + clk_cycles |= clk_40ns_cycles; + + err = ufshcd_dme_set(hba, + UIC_ARG_MIB(PA_VS_CORE_CLK_40NS_CYCLES), + clk_cycles); + } + + return err; +} + +static int ufs_qcom_cfg_core_clk_ctrl(struct ufs_hba *hba) +{ + struct list_head *head = &hba->clk_list_head; + struct ufs_clk_info *clki; + u32 max_freq = 0; + int err; + + list_for_each_entry(clki, head, list) { + if (!IS_ERR_OR_NULL(clki->clk) && + (!strcmp(clki->name, "core_clk_unipro"))) { + max_freq = clki->max_freq; + break; + } + } + + switch (max_freq) { + case MHZ_403: + err = ufs_qcom_set_core_clk_ctrl(hba, 403, 16, true); + break; + case MHZ_300: + err = ufs_qcom_set_core_clk_ctrl(hba, 300, 12, true); + break; + case MHZ_201_5: + err = ufs_qcom_set_core_clk_ctrl(hba, 202, 8, true); + break; + case MHZ_150: + err = ufs_qcom_set_core_clk_ctrl(hba, 150, 6, true); + break; + case MHZ_100: + err = ufs_qcom_set_core_clk_ctrl(hba, 100, 4, true); + break; + default: + dev_err(hba->dev, "unipro max_freq=%u entry missing\n", max_freq); + err = -EINVAL; + break; + } + + return err; +} static int ufs_qcom_link_startup_notify(struct ufs_hba *hba, enum ufs_notify_change_status status) { @@ -685,13 +802,15 @@ static int ufs_qcom_link_startup_notify(struct ufs_hba *hba, return -EINVAL; } - if (ufs_qcom_cap_qunipro(host)) - /* - * set unipro core clock cycles to 150 & clear clock - * divider - */ - err = ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(hba, - 150); + if (ufs_qcom_cap_qunipro(host)) { + err = ufs_qcom_cfg_core_clk_ctrl(hba); + if (err) { + dev_err(hba->dev, + "%s cfg core clk ctrl failed\n", + __func__); + return err; + } + } /* * Some UFS devices (and may be host) have issues if LCC is @@ -1296,69 +1415,52 @@ static void ufs_qcom_exit(struct ufs_hba *hba) phy_exit(host->generic_phy); } -static int ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(struct ufs_hba *hba, - u32 clk_cycles) +static int ufs_qcom_clk_scale_up_pre_change(struct ufs_hba *hba) { - int err; - u32 core_clk_ctrl_reg; - - if (clk_cycles > DME_VS_CORE_CLK_CTRL_MAX_CORE_CLK_1US_CYCLES_MASK) - return -EINVAL; - - err = ufshcd_dme_get(hba, - UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), - &core_clk_ctrl_reg); - if (err) - return err; - - core_clk_ctrl_reg &= ~DME_VS_CORE_CLK_CTRL_MAX_CORE_CLK_1US_CYCLES_MASK; - core_clk_ctrl_reg |= clk_cycles; - - /* Clear CORE_CLK_DIV_EN */ - core_clk_ctrl_reg &= ~DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT; + struct ufs_qcom_host *host = ufshcd_get_variant(hba); + struct ufs_pa_layer_attr *attr = &host->dev_req_params; + int err = 0; - return ufshcd_dme_set(hba, - UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), - core_clk_ctrl_reg); -} + if (!ufs_qcom_cap_qunipro(host)) + goto out; -static int ufs_qcom_clk_scale_up_pre_change(struct ufs_hba *hba) -{ - /* nothing to do as of now */ - return 0; + if (attr) { + err = __ufs_qcom_cfg_timers(hba, attr->gear_rx, + attr->pwr_rx, attr->hs_rate, + false, true); + if (err) + dev_err(hba->dev, "%s ufs cfg timer failed\n", + __func__); + } + err = ufs_qcom_cfg_core_clk_ctrl(hba); +out: + return err; } static int ufs_qcom_clk_scale_up_post_change(struct ufs_hba *hba) { - struct ufs_qcom_host *host = ufshcd_get_variant(hba); - - if (!ufs_qcom_cap_qunipro(host)) - return 0; - - /* set unipro core clock cycles to 150 and clear clock divider */ - return ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(hba, 150); + return 0; } static int ufs_qcom_clk_scale_down_pre_change(struct ufs_hba *hba) { struct ufs_qcom_host *host = ufshcd_get_variant(hba); int err; - u32 core_clk_ctrl_reg; + u32 reg; if (!ufs_qcom_cap_qunipro(host)) return 0; - err = ufshcd_dme_get(hba, - UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), - &core_clk_ctrl_reg); + err = ufshcd_dme_get(hba, UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), ®); + if (err) + return err; /* make sure CORE_CLK_DIV_EN is cleared */ - if (!err && - (core_clk_ctrl_reg & DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT)) { - core_clk_ctrl_reg &= ~DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT; + if (reg & CORE_CLK_DIV_EN_BIT) { + reg &= ~CORE_CLK_DIV_EN_BIT; err = ufshcd_dme_set(hba, UIC_ARG_MIB(DME_VS_CORE_CLK_CTRL), - core_clk_ctrl_reg); + reg); } return err; @@ -1367,12 +1469,44 @@ static int ufs_qcom_clk_scale_down_pre_change(struct ufs_hba *hba) static int ufs_qcom_clk_scale_down_post_change(struct ufs_hba *hba) { struct ufs_qcom_host *host = ufshcd_get_variant(hba); + struct ufs_pa_layer_attr *attr = &host->dev_req_params; + struct list_head *head = &hba->clk_list_head; + struct ufs_clk_info *clki; + u32 curr_freq = 0; + int err; if (!ufs_qcom_cap_qunipro(host)) return 0; - /* set unipro core clock cycles to 75 and clear clock divider */ - return ufs_qcom_set_dme_vs_core_clk_ctrl_clear_div(hba, 75); + if (attr) + ufs_qcom_cfg_timers(hba, attr->gear_rx, attr->pwr_rx, + attr->hs_rate, false); + + list_for_each_entry(clki, head, list) { + if (!IS_ERR_OR_NULL(clki->clk) && + (!strcmp(clki->name, "core_clk_unipro"))) { + curr_freq = clk_get_rate(clki->clk); + break; + } + } + + switch (curr_freq) { + case MHZ_37_5: + err = ufs_qcom_set_core_clk_ctrl(hba, 38, 2, false); + break; + case MHZ_75: + err = ufs_qcom_set_core_clk_ctrl(hba, 75, 3, false); + break; + case MHZ_100: + err = ufs_qcom_set_core_clk_ctrl(hba, 100, 4, false); + break; + default: + err = -EINVAL; + dev_err(hba->dev, "unipro curr_freq=%u entry missing\n", curr_freq); + break; + } + + return err; } static int ufs_qcom_clk_scale_notify(struct ufs_hba *hba, diff --git a/drivers/ufs/host/ufs-qcom.h b/drivers/ufs/host/ufs-qcom.h index d6f8e74bd538..da7b5ee7c1cf 100644 --- a/drivers/ufs/host/ufs-qcom.h +++ b/drivers/ufs/host/ufs-qcom.h @@ -79,6 +79,17 @@ enum { UFS_MEM_CQIS_VS = 0x8, }; + +/* QCOM UFS host controller core clk frequencies */ +#define MHZ_37_5 37500000 +#define MHZ_50 50000000 +#define MHZ_75 75000000 +#define MHZ_100 100000000 +#define MHZ_150 150000000 +#define MHZ_300 300000000 +#define MHZ_201_5 201500000 +#define MHZ_403 403000000 + #define UFS_CNTLR_2_x_x_VEN_REGS_OFFSET(x) (0x000 + x) #define UFS_CNTLR_3_x_x_VEN_REGS_OFFSET(x) (0x400 + x) @@ -129,9 +140,12 @@ enum { #define PA_VS_CONFIG_REG1 0x9000 #define DME_VS_CORE_CLK_CTRL 0xD002 /* bit and mask definitions for DME_VS_CORE_CLK_CTRL attribute */ -#define DME_VS_CORE_CLK_CTRL_CORE_CLK_DIV_EN_BIT BIT(8) -#define DME_VS_CORE_CLK_CTRL_MAX_CORE_CLK_1US_CYCLES_MASK 0xFF - +#define MAX_CORE_CLK_1US_CYCLES_MASK_V4 0xFFF +#define MAX_CORE_CLK_1US_CYCLES_OFFSET_V4 0x10 +#define MAX_CORE_CLK_1US_CYCLES_MASK 0xFF +#define CORE_CLK_DIV_EN_BIT BIT(8) +#define PA_VS_CORE_CLK_40NS_CYCLES 0x9007 +#define PA_VS_CORE_CLK_40NS_CYCLES_MASK 0x3F static inline void ufs_qcom_get_controller_revision(struct ufs_hba *hba, u8 *major, u16 *minor, u16 *step)