| Message ID | 20230821-ths-h616-v2-2-cda60d556798@somainline.org (mailing list archive) |
|---|---|
| State | New, archived |
| Delegated to: | Daniel Lezcano |
| Headers | show |
| Series | Add support for H616 Thermal system | expand |
On Mon, 21 Aug 2023 16:03:47 +0200 Martin Botka <martin.botka@somainline.org> wrote: Hi Martin, thanks for the changes, that looks good to me now. Just some tiny nitpick below, but only if you need to re-spin the series for whatever reason. > Add support for the thermal sensor found in H616 SoC > which slightly resembles the H6 thermal sensor > controller with few changes like 4 sensors. Regardless: > Signed-off-by: Martin Botka <martin.botka@somainline.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> > --- > drivers/thermal/sun8i_thermal.c | 74 +++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 74 insertions(+) > > diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c > index 195f3c5d0b38..cf96ab6a445b 100644 > --- a/drivers/thermal/sun8i_thermal.c > +++ b/drivers/thermal/sun8i_thermal.c > @@ -278,6 +278,66 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev, > return 0; > } > > +static int sun50i_h616_ths_calibrate(struct ths_device *tmdev, > + u16 *caldata, int callen) > +{ > + struct device *dev = tmdev->dev; > + int i, ft_temp; > + > + if (!caldata[0]) > + return -EINVAL; > + > + /* > + * h616 efuse THS calibration data layout: > + * > + * 0 11 16 27 32 43 48 57 > + * +----------+-----------+-----------+-----------+ > + * | temp | |sensor0| |sensor1| |sensor2| | > + * +----------+-----------+-----------+-----------+ > + * ^ ^ ^ > + * | | | > + * | | sensor3[11:8] > + * | sensor3[7:4] > + * sensor3[3:0] > + * > + * The calibration data on the H616 is the ambient temperature and > + * sensor values that are filled during the factory test stage. > + * > + * The unit of stored FT temperature is 0.1 degree celsius. > + */ > + ft_temp = caldata[0] & FT_TEMP_MASK; > + > + for (i = 0; i < tmdev->chip->sensor_num; i++) { > + int delta, cdata, offset, reg; > + > + if (i == 3) > + reg = (caldata[1] >> 12) > + | ((caldata[2] >> 12) << 4) > + | ((caldata[3] >> 12) << 8); > + else > + reg = (int)caldata[i + 1] & TEMP_CALIB_MASK; > + > + int sensor_temp = tmdev->chip->calc_temp(tmdev, i, reg); If you shorten that variable name by a bit, you can fit the division on the same line below. And that it looks all neat and satisfying again ;-) Cheers, Andre > + > + delta = (sensor_temp - ft_temp * 100) * 10; > + delta /= tmdev->chip->scale; > + cdata = CALIBRATE_DEFAULT - delta; > + if (cdata & ~TEMP_CALIB_MASK) { > + dev_warn(dev, "sensor%d is not calibrated.\n", i); > + > + continue; > + } > + > + offset = (i % 2) * 16; > + regmap_update_bits(tmdev->regmap, > + SUN50I_H6_THS_TEMP_CALIB + (i / 2 * 4), > + TEMP_CALIB_MASK << offset, > + cdata << offset); > + } > + > + return 0; > +} > + > static int sun8i_ths_calibrate(struct ths_device *tmdev) > { > struct nvmem_cell *calcell; > @@ -608,6 +668,19 @@ static const struct ths_thermal_chip sun50i_h6_ths = { > .calc_temp = sun8i_ths_calc_temp, > }; > > +static const struct ths_thermal_chip sun50i_h616_ths = { > + .sensor_num = 4, > + .has_bus_clk_reset = true, > + .ft_deviation = 8000, > + .offset = 263655, > + .scale = 810, > + .temp_data_base = SUN50I_H6_THS_TEMP_DATA, > + .calibrate = sun50i_h616_ths_calibrate, > + .init = sun50i_h6_thermal_init, > + .irq_ack = sun50i_h6_irq_ack, > + .calc_temp = sun8i_ths_calc_temp, > +}; > + > static const struct of_device_id of_ths_match[] = { > { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths }, > { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths }, > @@ -616,6 +689,7 @@ static const struct of_device_id of_ths_match[] = { > { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths }, > { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths }, > { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths }, > + { .compatible = "allwinner,sun50i-h616-ths", .data = &sun50i_h616_ths }, > { /* sentinel */ }, > }; > MODULE_DEVICE_TABLE(of, of_ths_match); >
Dne ponedeljek, 21. avgust 2023 ob 16:03:47 CEST je Martin Botka napisal(a): > Add support for the thermal sensor found in H616 SoC > which slightly resembles the H6 thermal sensor > controller with few changes like 4 sensors. > > Signed-off-by: Martin Botka <martin.botka@somainline.org> > --- > drivers/thermal/sun8i_thermal.c | 74 > +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 74 insertions(+) > > diff --git a/drivers/thermal/sun8i_thermal.c > b/drivers/thermal/sun8i_thermal.c index 195f3c5d0b38..cf96ab6a445b 100644 > --- a/drivers/thermal/sun8i_thermal.c > +++ b/drivers/thermal/sun8i_thermal.c > @@ -278,6 +278,66 @@ static int sun50i_h6_ths_calibrate(struct ths_device > *tmdev, return 0; > } > > +static int sun50i_h616_ths_calibrate(struct ths_device *tmdev, > + u16 *caldata, int callen) > +{ > + struct device *dev = tmdev->dev; > + int i, ft_temp; > + > + if (!caldata[0]) > + return -EINVAL; > + > + /* > + * h616 efuse THS calibration data layout: > + * > + * 0 11 16 27 32 43 48 57 > + * +----------+-----------+-----------+-----------+ > + * | temp | |sensor0| |sensor1| |sensor2| | > + * +----------+-----------+-----------+-----------+ > + * ^ ^ ^ > + * | | | > + * | | sensor3[11:8] > + * | sensor3[7:4] > + * sensor3[3:0] > + * > + * The calibration data on the H616 is the ambient temperature and > + * sensor values that are filled during the factory test stage. > + * > + * The unit of stored FT temperature is 0.1 degree celsius. > + */ > + ft_temp = caldata[0] & FT_TEMP_MASK; > + > + for (i = 0; i < tmdev->chip->sensor_num; i++) { > + int delta, cdata, offset, reg; > + > + if (i == 3) > + reg = (caldata[1] >> 12) > + | ((caldata[2] >> 12) << 4) > + | ((caldata[3] >> 12) << 8); > + else > + reg = (int)caldata[i + 1] & TEMP_CALIB_MASK; > + > + int sensor_temp = tmdev->chip->calc_temp(tmdev, i, reg); Variable declaration should be done at the beginning of code block. Best regards, Jernej > + > + delta = (sensor_temp - ft_temp * 100) * 10; > + delta /= tmdev->chip->scale; > + cdata = CALIBRATE_DEFAULT - delta; > + if (cdata & ~TEMP_CALIB_MASK) { > + dev_warn(dev, "sensor%d is not calibrated. \n", i); > + > + continue; > + } > + > + offset = (i % 2) * 16; > + regmap_update_bits(tmdev->regmap, > + SUN50I_H6_THS_TEMP_CALIB + (i / 2 * 4), > + TEMP_CALIB_MASK << offset, > + cdata << offset); > + } > + > + return 0; > +} > + > static int sun8i_ths_calibrate(struct ths_device *tmdev) > { > struct nvmem_cell *calcell; > @@ -608,6 +668,19 @@ static const struct ths_thermal_chip sun50i_h6_ths = { > .calc_temp = sun8i_ths_calc_temp, > }; > > +static const struct ths_thermal_chip sun50i_h616_ths = { > + .sensor_num = 4, > + .has_bus_clk_reset = true, > + .ft_deviation = 8000, > + .offset = 263655, > + .scale = 810, > + .temp_data_base = SUN50I_H6_THS_TEMP_DATA, > + .calibrate = sun50i_h616_ths_calibrate, > + .init = sun50i_h6_thermal_init, > + .irq_ack = sun50i_h6_irq_ack, > + .calc_temp = sun8i_ths_calc_temp, > +}; > + > static const struct of_device_id of_ths_match[] = { > { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths }, > { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths }, > @@ -616,6 +689,7 @@ static const struct of_device_id of_ths_match[] = { > { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths }, > { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths }, > { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths }, > + { .compatible = "allwinner,sun50i-h616-ths", .data = &sun50i_h616_ths }, > { /* sentinel */ }, > }; > MODULE_DEVICE_TABLE(of, of_ths_match);
On Wed, Aug 23 2023 at 09:38:30 PM +02:00:00, Jernej Škrabec <jernej.skrabec@gmail.com> wrote: > Dne ponedeljek, 21. avgust 2023 ob 16:03:47 CEST je Martin Botka > napisal(a): >> Add support for the thermal sensor found in H616 SoC >> which slightly resembles the H6 thermal sensor >> controller with few changes like 4 sensors. >> >> Signed-off-by: Martin Botka <martin.botka@somainline.org> >> --- >> drivers/thermal/sun8i_thermal.c | 74 >> +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 74 >> insertions(+) >> >> diff --git a/drivers/thermal/sun8i_thermal.c >> b/drivers/thermal/sun8i_thermal.c index 195f3c5d0b38..cf96ab6a445b >> 100644 >> --- a/drivers/thermal/sun8i_thermal.c >> +++ b/drivers/thermal/sun8i_thermal.c >> @@ -278,6 +278,66 @@ static int sun50i_h6_ths_calibrate(struct >> ths_device >> *tmdev, return 0; >> } >> >> +static int sun50i_h616_ths_calibrate(struct ths_device *tmdev, >> + u16 *caldata, int callen) >> +{ >> + struct device *dev = tmdev->dev; >> + int i, ft_temp; >> + >> + if (!caldata[0]) >> + return -EINVAL; >> + >> + /* >> + * h616 efuse THS calibration data layout: >> + * >> + * 0 11 16 27 32 43 48 57 >> + * +----------+-----------+-----------+-----------+ >> + * | temp | |sensor0| |sensor1| |sensor2| | >> + * +----------+-----------+-----------+-----------+ >> + * ^ ^ ^ >> + * | | | >> + * | | sensor3[11:8] >> + * | sensor3[7:4] >> + * sensor3[3:0] >> + * >> + * The calibration data on the H616 is the ambient temperature and >> + * sensor values that are filled during the factory test stage. >> + * >> + * The unit of stored FT temperature is 0.1 degree celsius. >> + */ >> + ft_temp = caldata[0] & FT_TEMP_MASK; >> + >> + for (i = 0; i < tmdev->chip->sensor_num; i++) { >> + int delta, cdata, offset, reg; >> + >> + if (i == 3) >> + reg = (caldata[1] >> 12) >> + | ((caldata[2] >> 12) << 4) >> + | ((caldata[3] >> 12) << 8); >> + else >> + reg = (int)caldata[i + 1] & TEMP_CALIB_MASK; >> + >> + int sensor_temp = tmdev->chip->calc_temp(tmdev, i, reg); > > Variable declaration should be done at the beginning of code block. Hello Jernej, Indeed. Will fix in next revision :) Cheers, Martin > > Best regards, > Jernej > >> + >> + delta = (sensor_temp - ft_temp * 100) * 10; >> + delta /= tmdev->chip->scale; >> + cdata = CALIBRATE_DEFAULT - delta; >> + if (cdata & ~TEMP_CALIB_MASK) { >> + dev_warn(dev, "sensor%d is not calibrated. > \n", i); >> + >> + continue; >> + } >> + >> + offset = (i % 2) * 16; >> + regmap_update_bits(tmdev->regmap, >> + SUN50I_H6_THS_TEMP_CALIB + (i / > 2 * 4), >> + TEMP_CALIB_MASK << offset, >> + cdata << offset); >> + } >> + >> + return 0; >> +} >> + >> static int sun8i_ths_calibrate(struct ths_device *tmdev) >> { >> struct nvmem_cell *calcell; >> @@ -608,6 +668,19 @@ static const struct ths_thermal_chip >> sun50i_h6_ths = { >> .calc_temp = sun8i_ths_calc_temp, >> }; >> >> +static const struct ths_thermal_chip sun50i_h616_ths = { >> + .sensor_num = 4, >> + .has_bus_clk_reset = true, >> + .ft_deviation = 8000, >> + .offset = 263655, >> + .scale = 810, >> + .temp_data_base = SUN50I_H6_THS_TEMP_DATA, >> + .calibrate = sun50i_h616_ths_calibrate, >> + .init = sun50i_h6_thermal_init, >> + .irq_ack = sun50i_h6_irq_ack, >> + .calc_temp = sun8i_ths_calc_temp, >> +}; >> + >> static const struct of_device_id of_ths_match[] = { >> { .compatible = "allwinner,sun8i-a83t-ths", .data = > &sun8i_a83t_ths }, >> { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths }, >> @@ -616,6 +689,7 @@ static const struct of_device_id of_ths_match[] >> = { >> { .compatible = "allwinner,sun50i-a100-ths", .data = > &sun50i_a100_ths }, >> { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths > }, >> { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths > }, >> + { .compatible = "allwinner,sun50i-h616-ths", .data = > &sun50i_h616_ths }, >> { /* sentinel */ }, >> }; >> MODULE_DEVICE_TABLE(of, of_ths_match); > > > >
On Mon, 21 Aug 2023 16:03:47 +0200 Martin Botka <martin.botka@somainline.org> wrote: Hi, > Add support for the thermal sensor found in H616 SoC > which slightly resembles the H6 thermal sensor > controller with few changes like 4 sensors. > > Signed-off-by: Martin Botka <martin.botka@somainline.org> So this doesn't work on both my OrangePi Zero3 and my X96 Mate, the values reported are way too high. The kernel gets immediately upset about the alleged >200C, and demands immediate shutdown. Those are the values from hwmon on the X96 Mate: /sys/class/hwmon/hwmon0/name:gpu_thermal /sys/class/hwmon/hwmon0/temp1_input:220301 /sys/class/hwmon/hwmon1/name:ve_thermal /sys/class/hwmon/hwmon1/temp1_input:219734 /sys/class/hwmon/hwmon2/name:cpu_thermal /sys/class/hwmon/hwmon2/temp1_input:220868 /sys/class/hwmon/hwmon3/name:ddr_thermal /sys/class/hwmon/hwmon3/temp1_input:221354 The raw values ranged from 0x273 till 0x294, with various values in between. The reported temperatures on the OPi Zero3 were a bit lower, but still around 200C. The calibration data in the fuses seems to be meaningful, it says the raw values are 0xb0f, 0xb18, 0xb14, 0xb1d for the four sensors, at an ambient temperature of 27C. Those raw values would translate to about 34C/42C, so not completely off the scale. This is as far as I dug today, maybe the sampling procedure is skewed, so the ADC returns wrong values? Or the calibration write to the THS is broken? Skipping that doesn't change the outcome significantly, though. Open to any ideas or debugging suggestions! Cheers, Andre > --- > drivers/thermal/sun8i_thermal.c | 74 +++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 74 insertions(+) > > diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c > index 195f3c5d0b38..cf96ab6a445b 100644 > --- a/drivers/thermal/sun8i_thermal.c > +++ b/drivers/thermal/sun8i_thermal.c > @@ -278,6 +278,66 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev, > return 0; > } > > +static int sun50i_h616_ths_calibrate(struct ths_device *tmdev, > + u16 *caldata, int callen) > +{ > + struct device *dev = tmdev->dev; > + int i, ft_temp; > + > + if (!caldata[0]) > + return -EINVAL; > + > + /* > + * h616 efuse THS calibration data layout: > + * > + * 0 11 16 27 32 43 48 57 > + * +----------+-----------+-----------+-----------+ > + * | temp | |sensor0| |sensor1| |sensor2| | > + * +----------+-----------+-----------+-----------+ > + * ^ ^ ^ > + * | | | > + * | | sensor3[11:8] > + * | sensor3[7:4] > + * sensor3[3:0] > + * > + * The calibration data on the H616 is the ambient temperature and > + * sensor values that are filled during the factory test stage. > + * > + * The unit of stored FT temperature is 0.1 degree celsius. > + */ > + ft_temp = caldata[0] & FT_TEMP_MASK; > + > + for (i = 0; i < tmdev->chip->sensor_num; i++) { > + int delta, cdata, offset, reg; > + > + if (i == 3) > + reg = (caldata[1] >> 12) > + | ((caldata[2] >> 12) << 4) > + | ((caldata[3] >> 12) << 8); > + else > + reg = (int)caldata[i + 1] & TEMP_CALIB_MASK; > + > + int sensor_temp = tmdev->chip->calc_temp(tmdev, i, reg); > + > + delta = (sensor_temp - ft_temp * 100) * 10; > + delta /= tmdev->chip->scale; > + cdata = CALIBRATE_DEFAULT - delta; > + if (cdata & ~TEMP_CALIB_MASK) { > + dev_warn(dev, "sensor%d is not calibrated.\n", i); > + > + continue; > + } > + > + offset = (i % 2) * 16; > + regmap_update_bits(tmdev->regmap, > + SUN50I_H6_THS_TEMP_CALIB + (i / 2 * 4), > + TEMP_CALIB_MASK << offset, > + cdata << offset); > + } > + > + return 0; > +} > + > static int sun8i_ths_calibrate(struct ths_device *tmdev) > { > struct nvmem_cell *calcell; > @@ -608,6 +668,19 @@ static const struct ths_thermal_chip sun50i_h6_ths = { > .calc_temp = sun8i_ths_calc_temp, > }; > > +static const struct ths_thermal_chip sun50i_h616_ths = { > + .sensor_num = 4, > + .has_bus_clk_reset = true, > + .ft_deviation = 8000, > + .offset = 263655, > + .scale = 810, > + .temp_data_base = SUN50I_H6_THS_TEMP_DATA, > + .calibrate = sun50i_h616_ths_calibrate, > + .init = sun50i_h6_thermal_init, > + .irq_ack = sun50i_h6_irq_ack, > + .calc_temp = sun8i_ths_calc_temp, > +}; > + > static const struct of_device_id of_ths_match[] = { > { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths }, > { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths }, > @@ -616,6 +689,7 @@ static const struct of_device_id of_ths_match[] = { > { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths }, > { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths }, > { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths }, > + { .compatible = "allwinner,sun50i-h616-ths", .data = &sun50i_h616_ths }, > { /* sentinel */ }, > }; > MODULE_DEVICE_TABLE(of, of_ths_match); >
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c index 195f3c5d0b38..cf96ab6a445b 100644 --- a/drivers/thermal/sun8i_thermal.c +++ b/drivers/thermal/sun8i_thermal.c @@ -278,6 +278,66 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev, return 0; } +static int sun50i_h616_ths_calibrate(struct ths_device *tmdev, + u16 *caldata, int callen) +{ + struct device *dev = tmdev->dev; + int i, ft_temp; + + if (!caldata[0]) + return -EINVAL; + + /* + * h616 efuse THS calibration data layout: + * + * 0 11 16 27 32 43 48 57 + * +----------+-----------+-----------+-----------+ + * | temp | |sensor0| |sensor1| |sensor2| | + * +----------+-----------+-----------+-----------+ + * ^ ^ ^ + * | | | + * | | sensor3[11:8] + * | sensor3[7:4] + * sensor3[3:0] + * + * The calibration data on the H616 is the ambient temperature and + * sensor values that are filled during the factory test stage. + * + * The unit of stored FT temperature is 0.1 degree celsius. + */ + ft_temp = caldata[0] & FT_TEMP_MASK; + + for (i = 0; i < tmdev->chip->sensor_num; i++) { + int delta, cdata, offset, reg; + + if (i == 3) + reg = (caldata[1] >> 12) + | ((caldata[2] >> 12) << 4) + | ((caldata[3] >> 12) << 8); + else + reg = (int)caldata[i + 1] & TEMP_CALIB_MASK; + + int sensor_temp = tmdev->chip->calc_temp(tmdev, i, reg); + + delta = (sensor_temp - ft_temp * 100) * 10; + delta /= tmdev->chip->scale; + cdata = CALIBRATE_DEFAULT - delta; + if (cdata & ~TEMP_CALIB_MASK) { + dev_warn(dev, "sensor%d is not calibrated.\n", i); + + continue; + } + + offset = (i % 2) * 16; + regmap_update_bits(tmdev->regmap, + SUN50I_H6_THS_TEMP_CALIB + (i / 2 * 4), + TEMP_CALIB_MASK << offset, + cdata << offset); + } + + return 0; +} + static int sun8i_ths_calibrate(struct ths_device *tmdev) { struct nvmem_cell *calcell; @@ -608,6 +668,19 @@ static const struct ths_thermal_chip sun50i_h6_ths = { .calc_temp = sun8i_ths_calc_temp, }; +static const struct ths_thermal_chip sun50i_h616_ths = { + .sensor_num = 4, + .has_bus_clk_reset = true, + .ft_deviation = 8000, + .offset = 263655, + .scale = 810, + .temp_data_base = SUN50I_H6_THS_TEMP_DATA, + .calibrate = sun50i_h616_ths_calibrate, + .init = sun50i_h6_thermal_init, + .irq_ack = sun50i_h6_irq_ack, + .calc_temp = sun8i_ths_calc_temp, +}; + static const struct of_device_id of_ths_match[] = { { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths }, { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths }, @@ -616,6 +689,7 @@ static const struct of_device_id of_ths_match[] = { { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths }, { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths }, { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths }, + { .compatible = "allwinner,sun50i-h616-ths", .data = &sun50i_h616_ths }, { /* sentinel */ }, }; MODULE_DEVICE_TABLE(of, of_ths_match);
Add support for the thermal sensor found in H616 SoC which slightly resembles the H6 thermal sensor controller with few changes like 4 sensors. Signed-off-by: Martin Botka <martin.botka@somainline.org> --- drivers/thermal/sun8i_thermal.c | 74 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 74 insertions(+)