| Message ID | 20230830123202.3408318-2-billy_tsai@aspeedtech.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Support pwm/tach driver for aspeed ast26xx | expand |
On Wed, Aug 30, 2023 at 08:32:00PM +0800, Billy Tsai wrote: > From: Naresh Solanki <naresh.solanki@9elements.com> > > Add common fan properties bindings to a schema. > > Bindings for fan controllers can reference the common schema for the > fan > > child nodes: > > patternProperties: > "^fan@[0-2]": > type: object > $ref: fan-common.yaml# unevaluatedProperties: false > > Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com> > Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> > --- > .../devicetree/bindings/hwmon/fan-common.yaml | 63 +++++++++++++++++++ > 1 file changed, 63 insertions(+) > create mode 100644 Documentation/devicetree/bindings/hwmon/fan-common.yaml > > diff --git a/Documentation/devicetree/bindings/hwmon/fan-common.yaml b/Documentation/devicetree/bindings/hwmon/fan-common.yaml > new file mode 100644 > index 000000000000..a69b4d553e45 > --- /dev/null > +++ b/Documentation/devicetree/bindings/hwmon/fan-common.yaml > @@ -0,0 +1,63 @@ > +# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause Drop 'or-later'. It's GPL2 only. > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/hwmon/fan-common.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Common Fan Properties > + > +maintainers: > + - Naresh Solanki <naresh.solanki@9elements.com> > + - Billy Tsai <billy_tsai@aspeedtech.com> > + > +properties: > + max-rpm: > + description: > + Max RPM supported by fan. > + $ref: /schemas/types.yaml#/definitions/uint32 Physics will limit this to something much less than 2^32. Add some constraints. 10000? > + > + min-rpm: > + description: > + Min RPM supported by fan. > + $ref: /schemas/types.yaml#/definitions/uint32 ditto > + > + pulses-per-revolution: > + description: > + The number of pulse from fan sensor per revolution. > + $ref: /schemas/types.yaml#/definitions/uint32 Needs constraints. I assume this is never more than 4 (or 2 even)? > + div: Too generic of a name. > + description: > + Fan clock divisor But what is a fan clock? > + $ref: /schemas/types.yaml#/definitions/uint32 > + > + target-rpm: > + description: > + Target RPM the fan should be configured during driver probe. What driver? By the time the OS driver runs, a bunch of other boot software has already run on modern systems. So this value would likely be used much earlier. The point is that when exactly is outside the scope of DT. This is "what RPM do I use in case of no other information (e.g. temperature)". > + $ref: /schemas/types.yaml#/definitions/uint32 > + > + mode: Too generic. > + description: > + Select the operational mode of the fan. What are modes? Spin and don't spin? > + $ref: /schemas/types.yaml#/definitions/uint32 > + > + pwms: > + description: > + PWM provider. maxItems: 1 I don't think there are fans with more than 1 PWM input? > + > + tach-ch: > + description: > + The tach channel used for the fan. > + $ref: /schemas/types.yaml#/definitions/uint32 The existing ASpeed version of this property allows more than 1 entry. I don't understand how a fan would have 2 tach signals, but if so, the generic property should allow for that. Perhaps 'reg' should be defined in here with some text saying 'reg' corresponds to the fan controller specific id which may be the PWM+TACH channel, PWM channel (deprecated), or TACH channel. I think there are examples of all 3 of these cases. > + > + label: > + description: > + Optional fan label > + > + fan-supply: > + description: > + Power supply for fan. > + > +additionalProperties: true > + > +... > -- > 2.25.1 >
On Wed, Aug 30, 2023 at 08:32:00PM +0800, Billy Tsai wrote: >> From: Naresh Solanki <naresh.solanki@9elements.com> >> >> Add common fan properties bindings to a schema. >> >> Bindings for fan controllers can reference the common schema for the >> fan >> >> child nodes: >> >> patternProperties: >> "^fan@[0-2]": >> type: object >> $ref: fan-common.yaml# > unevaluatedProperties: false OK, I will add this. >> >> Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com> >> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> >> --- >> .../devicetree/bindings/hwmon/fan-common.yaml | 63 +++++++++++++++++++ >> 1 file changed, 63 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/hwmon/fan-common.yaml >> >> diff --git a/Documentation/devicetree/bindings/hwmon/fan-common.yaml b/Documentation/devicetree/bindings/>hwmon/fan-common.yaml >> new file mode 100644 >> index 000000000000..a69b4d553e45 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/hwmon/fan-common.yaml >> @@ -0,0 +1,63 @@ >> +# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause > Drop 'or-later'. It's GPL2 only. OK, I will fix it. >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/hwmon/fan-common.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Common Fan Properties >> + >> +maintainers: >> + - Naresh Solanki <naresh.solanki@9elements.com> >> + - Billy Tsai <billy_tsai@aspeedtech.com> >> + >> +properties: >> + max-rpm: >> + description: >> + Max RPM supported by fan. >> + $ref: /schemas/types.yaml#/definitions/uint32 > Physics will limit this to something much less than 2^32. Add some > constraints. 10000? >> + >> + min-rpm: >> + description: >> + Min RPM supported by fan. >> + $ref: /schemas/types.yaml#/definitions/uint32 > ditto >> + >> + pulses-per-revolution: >> + description: >> + The number of pulse from fan sensor per revolution. >> + $ref: /schemas/types.yaml#/definitions/uint32 >Needs constraints. I assume this is never more than 4 (or 2 even)? Do you think we should add the contraint in the common binding? In my option, the limit of the max/min rpm should be declared by the binding if necessary, because the usage of each fan monitor is based on the connection of the tach pin. >> + div: > Too generic of a name. >> + description: >> + Fan clock divisor > But what is a fan clock? This is the divisor for the tachometer sampling clock, which determines the sensitivity of the tach pin. So, if the name of the property changes to 'tach-div,' is it acceptable to you? >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + >> + target-rpm: >> + description: >> + Target RPM the fan should be configured during driver probe. > What driver? By the time the OS driver runs, a bunch of other boot > software has already run on modern systems. So this value would likely > be used much earlier. The point is that when exactly is outside the > scope of DT. This is "what RPM do I use in case of no other information > (e.g. temperature)". So, the description should be changed to 'The default desired fan speed in RPM,' and we shouldn't mention the timing of the property's operation in the DT, is that correct? >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + >> + mode: > Too generic. >> + description: >> + Select the operational mode of the fan. > What are modes? Spin and don't spin? The mode is used to indicate the driving mode of the fan (DC, PWM and so on). So, if the name of the property changes to 'fan-driving-mode,' is it acceptable to you? >> + $ref: /schemas/types.yaml#/definitions/uint32 >> + >> + pwms: >> + description: >> + PWM provider. > maxItems: 1 > I don't think there are fans with more than 1 PWM input? Ok, I will add the constraint for the pwm input. >> + >> + tach-ch: >> + description: >> + The tach channel used for the fan. >> + $ref: /schemas/types.yaml#/definitions/uint32 > The existing ASpeed version of this property allows more than 1 entry. I > don't understand how a fan would have 2 tach signals, but if so, the > generic property should allow for that. Ok, I will modify it to the uint32-array > Perhaps 'reg' should be defined in here with some text saying 'reg' > corresponds to the fan controller specific id which may be the PWM+TACH > channel, PWM channel (deprecated), or TACH channel. I think there are > examples of all 3 of these cases. I don't think it's necessary for the 'reg' because the case you mentioned is already covered by the property 'tach-ch' and the 'pwms'. > + > + label: > + description: > + Optional fan label > + > + fan-supply: > + description: > + Power supply for fan. > + > +additionalProperties: true > + > +... > -- > 2.25.1 >
On Thu, Sep 07, 2023 at 07:17:55AM +0000, Billy Tsai wrote: > On Wed, Aug 30, 2023 at 08:32:00PM +0800, Billy Tsai wrote: > >> From: Naresh Solanki <naresh.solanki@9elements.com> > >> > >> Add common fan properties bindings to a schema. > >> > >> Bindings for fan controllers can reference the common schema for the > >> fan > >> +properties: > >> + max-rpm: > >> + description: > >> + Max RPM supported by fan. > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > Physics will limit this to something much less than 2^32. Add some > > constraints. 10000? > > > >> + > >> + min-rpm: > >> + description: > >> + Min RPM supported by fan. > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > ditto > > >> + > >> + pulses-per-revolution: > >> + description: > >> + The number of pulse from fan sensor per revolution. > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > >Needs constraints. I assume this is never more than 4 (or 2 even)? > > Do you think we should add the contraint in the common binding? > In my option, the limit of the max/min rpm should be declared by > the binding if necessary, because the usage of each fan monitor is > based on the connection of the tach pin. Yes, I think we should have default limits. Unless we go as far as a schema for every specific fan model, then there is actually no way we can have specific limits unless the fan controllers have some limits. The most I see in tree for pulses-per-revolution is 2. There's no value in more. So set the max to 4 and then if anyone needs more they can bump the value. Or maybe there's some electrical/mechanical design reason fans are 1 or 2 pulses and we'll never see anything else? This document[1] seems to indicate that is indeed the case. (First hit googling "fan tach signal pulses") > > > >> + div: > > > Too generic of a name. > > >> + description: > >> + Fan clock divisor > > > But what is a fan clock? > > This is the divisor for the tachometer sampling clock, which determines the sensitivity of the tach pin. > So, if the name of the property changes to 'tach-div,' is it acceptable to you? That sounds like a property of the controller, not the fan, so it belongs in the controller binding. Is this really a common thing? > >> + $ref: /schemas/types.yaml#/definitions/uint32 > >> + > >> + target-rpm: > >> + description: > >> + Target RPM the fan should be configured during driver probe. > > > What driver? By the time the OS driver runs, a bunch of other boot > > software has already run on modern systems. So this value would likely > > be used much earlier. The point is that when exactly is outside the > > scope of DT. This is "what RPM do I use in case of no other information > > (e.g. temperature)". > > So, the description should be changed to 'The default desired fan speed in RPM,' > and we shouldn't mention the timing of the property's operation in the DT, is that correct? Correct. > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > >> + > >> + mode: > > > Too generic. > > >> + description: > >> + Select the operational mode of the fan. > > > What are modes? Spin and don't spin? > > The mode is used to indicate the driving mode of the fan (DC, PWM and so on). > So, if the name of the property changes to 'fan-driving-mode,' is it acceptable to you? I tend to think that should be implied from the parent node and/or other properties. PWM if "pwms" property is present. DC if the supply is variable. We could also use compatible strings in the fan nodes if there's a need. That reminds me, both of these modes probably need a table of voltage/duty-cycle to RPMs. I imagine it's not always a linear response. Naresh also privately sent me (don't do that) an updated common binding which we discussed the need for this. I expect him to comment further with details. > >> + $ref: /schemas/types.yaml#/definitions/uint32 > >> + > >> + pwms: > >> + description: > >> + PWM provider. > > > maxItems: 1 > > > I don't think there are fans with more than 1 PWM input? > > Ok, I will add the constraint for the pwm input. > > >> + > >> + tach-ch: > >> + description: > >> + The tach channel used for the fan. > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > The existing ASpeed version of this property allows more than 1 entry. I > > don't understand how a fan would have 2 tach signals, but if so, the > > generic property should allow for that. > > Ok, I will modify it to the uint32-array Perhaps uint8-array to align with existing versions of the property. > > > Perhaps 'reg' should be defined in here with some text saying 'reg' > > corresponds to the fan controller specific id which may be the PWM+TACH > > channel, PWM channel (deprecated), or TACH channel. I think there are > > examples of all 3 of these cases. > > I don't think it's necessary for the 'reg' because the case you mentioned is > already covered by the property 'tach-ch' and the 'pwms'. Yes, but when we have N child nodes of the same thing, we usually have "reg" and its value corresponds to how the parent identifies each child. We already have a mixture using PWM or tach channel. Yes, this can all just be in the fan controllers binding, but putting it here would just document the options. Rob [1] http://www.comairrotron.com/methods-monitoring-fan-performance
On Thu, Sep 07, 2023 at 07:17:55AM +0000, Billy Tsai wrote: > > On Wed, Aug 30, 2023 at 08:32:00PM +0800, Billy Tsai wrote: > > >> From: Naresh Solanki <naresh.solanki@9elements.com> > > >> > > >> Add common fan properties bindings to a schema. > > >> > > >> Bindings for fan controllers can reference the common schema for the > > >> fan > > >> +properties: > > >> + max-rpm: > > >> + description: > > >> + Max RPM supported by fan. > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > > > Physics will limit this to something much less than 2^32. Add some > > > constraints. 10000? > > > > > > >> + > > >> + min-rpm: > > >> + description: > > >> + Min RPM supported by fan. > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > > > ditto > > > > >> + > > >> + pulses-per-revolution: > > >> + description: > > >> + The number of pulse from fan sensor per revolution. > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > > >Needs constraints. I assume this is never more than 4 (or 2 even)? > > > > Do you think we should add the contraint in the common binding? > > In my option, the limit of the max/min rpm should be declared by > > the binding if necessary, because the usage of each fan monitor is > > based on the connection of the tach pin. > Yes, I think we should have default limits. > Unless we go as far as a schema for every specific fan model, then there > is actually no way we can have specific limits unless the fan > controllers have some limits. > The most I see in tree for pulses-per-revolution is 2. There's no value > in more. So set the max to 4 and then if anyone needs more they can bump > the value. > Or maybe there's some electrical/mechanical design reason fans are 1 or > 2 pulses and we'll never see anything else? This document[1] seems to > indicate that is indeed the case. (First hit googling "fan tach signal > pulses") OK, I will add the maximum value for the max-rpm, min-rpm and pulses-per-revolution. > > > > > > >> + div: > > > > > Too generic of a name. > > > > >> + description: > > >> + Fan clock divisor > > > > > But what is a fan clock? > > > > This is the divisor for the tachometer sampling clock, which determines the sensitivity of the tach pin. > > So, if the name of the property changes to 'tach-div,' is it acceptable to you? > That sounds like a property of the controller, not the fan, so it > belongs in the controller binding. Is this really a common thing? Yes, I believe this is a common feature for fans. You can refer to the Documentation/hwmon/sysfs-interface.rst, where the fan divisor is defined for users, determining the fan's sensitivity. > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > >> + > > >> + target-rpm: > > >> + description: > > >> + Target RPM the fan should be configured during driver probe. > > > > > What driver? By the time the OS driver runs, a bunch of other boot > > > software has already run on modern systems. So this value would likely > > > be used much earlier. The point is that when exactly is outside the > > > scope of DT. This is "what RPM do I use in case of no other information > > > (e.g. temperature)". > > > > So, the description should be changed to 'The default desired fan speed in RPM,' > > and we shouldn't mention the timing of the property's operation in the DT, is that correct? > Correct. > > > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > >> + > > >> + mode: > > > > > Too generic. > > > > >> + description: > > >> + Select the operational mode of the fan. > > > > > What are modes? Spin and don't spin? > > > > The mode is used to indicate the driving mode of the fan (DC, PWM and so on). > > So, if the name of the property changes to 'fan-driving-mode,' is it acceptable to you? > I tend to think that should be implied from the parent node and/or other > properties. PWM if "pwms" property is present. DC if the supply is > variable. We could also use compatible strings in the fan nodes if > there's a need. So, it looks that this property isn't necessary for the fan. And it should be determined by the present of the driving source. is that correct? > That reminds me, both of these modes probably need a table of > voltage/duty-cycle to RPMs. I imagine it's not always a linear response. > Naresh also privately sent me (don't do that) an updated common binding > which we discussed the need for this. I expect him to comment further > with details. For this purpose, we should add the speed-map like the usage of the gpio-fan, right? https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/hwmon/gpio-fan.txt > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > >> + > > >> + pwms: > > >> + description: > > >> + PWM provider. > > > > > maxItems: 1 > > > > > I don't think there are fans with more than 1 PWM input? > > > > Ok, I will add the constraint for the pwm input. > > > > >> + > > >> + tach-ch: > > >> + description: > > >> + The tach channel used for the fan. > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > > > The existing ASpeed version of this property allows more than 1 entry. I > > > don't understand how a fan would have 2 tach signals, but if so, the > > > generic property should allow for that. > > > > Ok, I will modify it to the uint32-array > Perhaps uint8-array to align with existing versions of the property. Ok, I will modify it to the uint8-array. > > > > > Perhaps 'reg' should be defined in here with some text saying 'reg' > > > corresponds to the fan controller specific id which may be the PWM+TACH > > > channel, PWM channel (deprecated), or TACH channel. I think there are > > > examples of all 3 of these cases. > > > > I don't think it's necessary for the 'reg' because the case you mentioned is > > already covered by the property 'tach-ch' and the 'pwms'. > Yes, but when we have N child nodes of the same thing, we usually have > "reg" and its value corresponds to how the parent identifies each child. > We already have a mixture using PWM or tach channel. Yes, this can all > just be in the fan controllers binding, but putting it here would just > document the options. Ok, I will add reg property for the option. > Rob > [1] http://www.comairrotron.com/methods-monitoring-fan-performance
On Fri, Sep 08, 2023 at 08:49:25AM +0000, Billy Tsai wrote: > On Thu, Sep 07, 2023 at 07:17:55AM +0000, Billy Tsai wrote: > > > On Wed, Aug 30, 2023 at 08:32:00PM +0800, Billy Tsai wrote: > > > >> From: Naresh Solanki <naresh.solanki@9elements.com> > > > >> > > > >> Add common fan properties bindings to a schema. > > > >> > > > >> Bindings for fan controllers can reference the common schema for the > > > >> fan > > > > > >> +properties: > > > >> + max-rpm: > > > >> + description: > > > >> + Max RPM supported by fan. > > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > > > > > Physics will limit this to something much less than 2^32. Add some > > > > constraints. 10000? > > > > > > > > > >> + > > > >> + min-rpm: > > > >> + description: > > > >> + Min RPM supported by fan. > > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > > > > > ditto > > > > > > >> + > > > >> + pulses-per-revolution: > > > >> + description: > > > >> + The number of pulse from fan sensor per revolution. > > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > > > > >Needs constraints. I assume this is never more than 4 (or 2 even)? > > > > > > Do you think we should add the contraint in the common binding? > > > In my option, the limit of the max/min rpm should be declared by > > > the binding if necessary, because the usage of each fan monitor is > > > based on the connection of the tach pin. > > > Yes, I think we should have default limits. > > > Unless we go as far as a schema for every specific fan model, then there > > is actually no way we can have specific limits unless the fan > > controllers have some limits. > > > The most I see in tree for pulses-per-revolution is 2. There's no value > > in more. So set the max to 4 and then if anyone needs more they can bump > > the value. > > > Or maybe there's some electrical/mechanical design reason fans are 1 or > > 2 pulses and we'll never see anything else? This document[1] seems to > > indicate that is indeed the case. (First hit googling "fan tach signal > > pulses") > > OK, I will add the maximum value for the max-rpm, min-rpm and pulses-per-revolution. > > > > > > > > > > >> + div: > > > > > > > Too generic of a name. > > > > > > >> + description: > > > >> + Fan clock divisor > > > > > > > But what is a fan clock? > > > > > > This is the divisor for the tachometer sampling clock, which determines the sensitivity of the tach pin. > > > So, if the name of the property changes to 'tach-div,' is it acceptable to you? > > > That sounds like a property of the controller, not the fan, so it > > belongs in the controller binding. Is this really a common thing? > > Yes, I believe this is a common feature for fans. You can refer to the Documentation/hwmon/sysfs-interface.rst, > where the fan divisor is defined for users, determining the fan's sensitivity. It's a feature of the controller, but I guess since it may be a per fan or tach channel setting having it in the fan node is fine. 'tach-div' is fine. > > > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > >> + > > > >> + target-rpm: > > > >> + description: > > > >> + Target RPM the fan should be configured during driver probe. > > > > > > > What driver? By the time the OS driver runs, a bunch of other boot > > > > software has already run on modern systems. So this value would likely > > > > be used much earlier. The point is that when exactly is outside the > > > > scope of DT. This is "what RPM do I use in case of no other information > > > > (e.g. temperature)". > > > > > > So, the description should be changed to 'The default desired fan speed in RPM,' > > > and we shouldn't mention the timing of the property's operation in the DT, is that correct? > > > Correct. > > > > > > > >> + $ref: /schemas/types.yaml#/definitions/uint32 > > > >> + > > > >> + mode: > > > > > > > Too generic. > > > > > > >> + description: > > > >> + Select the operational mode of the fan. > > > > > > > What are modes? Spin and don't spin? > > > > > > The mode is used to indicate the driving mode of the fan (DC, PWM and so on). > > > So, if the name of the property changes to 'fan-driving-mode,' is it acceptable to you? > > > I tend to think that should be implied from the parent node and/or other > > properties. PWM if "pwms" property is present. DC if the supply is > > variable. We could also use compatible strings in the fan nodes if > > there's a need. > > So, it looks that this property isn't necessary for the fan. And it should be determined by the > present of the driving source. is that correct? Looking back, I see Guenter asked for something like this. So I guess it is fine to keep if he still thinks we need it. I think it could also be implied a bit more clearly if we do 'cooling-levels' as below. The fan controller should know what modes it can do. Duty cycle vs. voltage in uV is pretty easy to distinguish. > > > That reminds me, both of these modes probably need a table of > > voltage/duty-cycle to RPMs. I imagine it's not always a linear response. > > Naresh also privately sent me (don't do that) an updated common binding > > which we discussed the need for this. I expect him to comment further > > with details. > > For this purpose, we should add the speed-map like the usage of the gpio-fan, right? > https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/hwmon/gpio-fan.txt That should be fine. I guess it comes down to whether we want one property or 3 depending on whether the control is voltage, duty-cycle, GPIO pins state, etc. Unfortunately, it's "gpio-fan,speed-map", not "speed-map", so we can't use that as-is. There's also "cooling-levels" which can accomplish the same thing. We don't know RPMs with that, but do we need to? Maybe, as it seems some drivers want to set speed in RPMs from userspace. Could also do something like this: cooling-levels = < 33 66 100>; rpm-levels = <500 1000 1500>; "rpm-levels" would replace the min-rpm/max-rpm properties. Also, looking at gpio-fan.txt, it looks like you should add "#cooling-cells" as well. Rob
diff --git a/Documentation/devicetree/bindings/hwmon/fan-common.yaml b/Documentation/devicetree/bindings/hwmon/fan-common.yaml new file mode 100644 index 000000000000..a69b4d553e45 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/fan-common.yaml @@ -0,0 +1,63 @@ +# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/hwmon/fan-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Fan Properties + +maintainers: + - Naresh Solanki <naresh.solanki@9elements.com> + - Billy Tsai <billy_tsai@aspeedtech.com> + +properties: + max-rpm: + description: + Max RPM supported by fan. + $ref: /schemas/types.yaml#/definitions/uint32 + + min-rpm: + description: + Min RPM supported by fan. + $ref: /schemas/types.yaml#/definitions/uint32 + + pulses-per-revolution: + description: + The number of pulse from fan sensor per revolution. + $ref: /schemas/types.yaml#/definitions/uint32 + + div: + description: + Fan clock divisor + $ref: /schemas/types.yaml#/definitions/uint32 + + target-rpm: + description: + Target RPM the fan should be configured during driver probe. + $ref: /schemas/types.yaml#/definitions/uint32 + + mode: + description: + Select the operational mode of the fan. + $ref: /schemas/types.yaml#/definitions/uint32 + + pwms: + description: + PWM provider. + + tach-ch: + description: + The tach channel used for the fan. + $ref: /schemas/types.yaml#/definitions/uint32 + + label: + description: + Optional fan label + + fan-supply: + description: + Power supply for fan. + +additionalProperties: true + +...