new file mode 100644
@@ -0,0 +1,249 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/marvell,mv88e6xxx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell MV88E6xxx switch family
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+
+description:
+ The Marvell MV88E6xxx switch series has been produced and sold
+ by Marvell since at least 2010. The switch has a few compatibles which
+ just indicate the base address of the switch, then operating systems
+ can investigate switch ID registers to find out which actual version
+ of the switch it is dealing with.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - marvell,mv88e6060
+ - marvell,mv88e6085
+ - marvell,mv88e6190
+ - marvell,mv88e6250
+ description: |
+ marvell,mv88e6060: The oldest Marvell switch supported (singular version)
+ marvell,mv88e6085: This switch uses base address 0x10.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6085" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, 6171, 6172, 6175, 6176,
+ 6185, 6240, 6320, 6321, 6341, 6350, 6351, 6352
+ marvell,mv88e6190: This switch uses base address 0x00.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6190" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6190, 6190X, 6191, 6290, 6361, 6390, 6390X
+ marvell,mv88e6250: This switch uses base address 0x08 or 0x18.
+ This switch and its siblings will be autodetected from
+ ID registers found in the switch, so only "marvell,mv88e6250" should be
+ specified. This includes the following list of MV88Exxxx switches:
+ 6220, 6250
+ reg:
+ maxItems: 1
+
+ eeprom-length:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: Set to the length of an EEPROM connected to the switch. Must be
+ set if the switch can not detect the presence and/or size of a connected
+ EEPROM, otherwise optional.
+
+ reset-gpios:
+ description:
+ GPIO to be used to reset the whole device
+ maxItems: 1
+
+ interrupts:
+ description: The switch provides an external interrupt line, but it is
+ not always used by target systems.
+ maxItems: 1
+
+ interrupt-controller:
+ description: The switch has an internal interrupt controller used by
+ the different sub-blocks.
+
+ '#interrupt-cells':
+ description: The internal interrupt controller only supports triggering
+ on IRQ_TYPE_LEVEL_HIGH
+ # FIXME: what is this? this should be one cell should it not?
+ # the Linux mv88e6xxx driver does not implement .irq_set_type in its irq_chip
+ # so at least in that implementation the type is flat out ignored.
+ const: 2
+
+ mdio:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+ description: Marvell MV88E6xxx switches have an internal mdio bus to
+ access switch ports, which is handled in this node.
+
+ mdio-external:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+ description: Marvell MV88E6xxx switches have an external mdio bus to
+ access switch ports.
+
+ mdio1:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+ description: Older version of mdio-external
+ deprecated: true
+ properties:
+ compatible:
+ const: marvell,mv88e6xxx-mdio-external
+
+ required:
+ - compatible
+
+$ref: dsa.yaml#
+
+patternProperties:
+ "^(ethernet-)?ports$":
+ type: object
+ patternProperties:
+ "^(ethernet-)?port@[0-9a-f]+$":
+ type: object
+ description: Ethernet switch ports
+
+ $ref: dsa-port.yaml#
+
+ unevaluatedProperties: false
+
+oneOf:
+ - required:
+ - ports
+ - required:
+ - ethernet-ports
+
+required:
+ - compatible
+ - reg
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch0: switch@0 {
+ compatible = "marvell,mv88e6085";
+ reg = <0>;
+ reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@5 {
+ reg = <5>;
+ phy-mode = "sgmii";
+ ethernet = <ð2>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch0phy0: switch0phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch0>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+ };
+ };
+
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch1: switch@0 {
+ compatible = "marvell,mv88e6190";
+ reg = <0>;
+ reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch1phy0: switch1phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch1>;
+ interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ mdio-external {
+ compatible = "marvell,mv88e6xxx-mdio-external";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ switch1phy9: switch1phy@9 {
+ reg = <9>;
+ };
+ };
+ };
+ };
deleted file mode 100644
@@ -1,109 +0,0 @@
-Marvell DSA Switch Device Tree Bindings
----------------------------------------
-
-WARNING: This binding is currently unstable. Do not program it into a
-FLASH never to be changed again. Once this binding is stable, this
-warning will be removed.
-
-If you need a stable binding, use the old dsa.txt binding.
-
-Marvell Switches are MDIO devices. The following properties should be
-placed as a child node of an mdio device.
-
-The properties described here are those specific to Marvell devices.
-Additional required and optional properties can be found in dsa.txt.
-
-The compatibility string is used only to find an identification register,
-which is at a different MDIO base address in different switch families.
-- "marvell,mv88e6085" : Switch has base address 0x10. Use with models:
- 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
- 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
- 6341, 6350, 6351, 6352
-- "marvell,mv88e6190" : Switch has base address 0x00. Use with models:
- 6190, 6190X, 6191, 6290, 6361, 6390, 6390X
-- "marvell,mv88e6250" : Switch has base address 0x08 or 0x18. Use with model:
- 6220, 6250
-
-Required properties:
-- compatible : Should be one of "marvell,mv88e6085",
- "marvell,mv88e6190" or "marvell,mv88e6250" as
- indicated above
-- reg : Address on the MII bus for the switch.
-
-Optional properties:
-
-- reset-gpios : Should be a gpio specifier for a reset line
-- interrupts : Interrupt from the switch
-- interrupt-controller : Indicates the switch is itself an interrupt
- controller. This is used for the PHY interrupts.
-#interrupt-cells = <2> : Controller uses two cells, number and flag
-- eeprom-length : Set to the length of an EEPROM connected to the
- switch. Must be set if the switch can not detect
- the presence and/or size of a connected EEPROM,
- otherwise optional.
-- mdio : Container of PHY and devices on the switches MDIO
- bus.
-- mdio? : Container of PHYs and devices on the external MDIO
- bus. The node must contains a compatible string of
- "marvell,mv88e6xxx-mdio-external"
-
-Example:
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <&gpio0>;
- interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- switch0: switch@0 {
- compatible = "marvell,mv88e6085";
- reg = <0>;
- reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy0: switch1phy0@0 {
- reg = <0>;
- interrupt-parent = <&switch0>;
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- interrupt-parent = <&gpio0>;
- interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- switch0: switch@0 {
- compatible = "marvell,mv88e6190";
- reg = <0>;
- reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy0: switch1phy0@0 {
- reg = <0>;
- interrupt-parent = <&switch0>;
- interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
-
- mdio1 {
- compatible = "marvell,mv88e6xxx-mdio-external";
- #address-cells = <1>;
- #size-cells = <0>;
- switch1phy9: switch1phy0@9 {
- reg = <9>;
- };
- };
- };
- };
@@ -12625,7 +12625,7 @@ MARVELL 88E6XXX ETHERNET SWITCH FABRIC DRIVER
M: Andrew Lunn <andrew@lunn.ch>
L: netdev@vger.kernel.org
S: Maintained
-F: Documentation/devicetree/bindings/net/dsa/marvell.txt
+F: Documentation/devicetree/bindings/net/dsa/marvell,mv88e6xxx.yaml
F: Documentation/networking/devlink/mv88e6xxx.rst
F: drivers/net/dsa/mv88e6xxx/
F: include/linux/dsa/mv88e6xxx.h
This is an attempt to rewrite the Marvell MV88E6xxx switch bindings in YAML schema. The current text binding says: WARNING: This binding is currently unstable. Do not program it into a FLASH never to be changed again. Once this binding is stable, this warning will be removed. Well that never happened before we switched to YAML markup, we can't have it like this, what about fixing the mess? Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- .../bindings/net/dsa/marvell,mv88e6xxx.yaml | 249 +++++++++++++++++++++ .../devicetree/bindings/net/dsa/marvell.txt | 109 --------- MAINTAINERS | 2 +- 3 files changed, 250 insertions(+), 110 deletions(-)