| Message ID | 20231016040132.23824-1-kai.heng.feng@canonical.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | PCI: pciehp: Prevent child devices from doing RPM on PCIe Link Down | expand |
On Mon, Oct 16, 2023 at 12:01:31PM +0800, Kai-Heng Feng wrote: > When inserting an SD7.0 card to Realtek card reader, it can trigger PCI > slot Link down and causes the following error: Why does *inserting* a card cause a Link Down? > [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 63.912118] BUG: unable to handle page fault for address: ffffb24d403e5010 [...] > [ 63.912198] ? asm_exc_page_fault+0x27/0x30 > [ 63.912203] ? ioread32+0x2e/0x70 > [ 63.912206] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] > [ 63.912217] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] > [ 63.912226] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] > [ 63.912234] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] > [ 63.912243] ? __pfx_pci_pm_runtime_idle+0x10/0x10 > [ 63.912246] pci_pm_runtime_idle+0x34/0x70 > [ 63.912248] rpm_idle+0xc4/0x2b0 > [ 63.912251] pm_runtime_work+0x93/0xc0 > [ 63.912254] process_one_work+0x21a/0x430 > [ 63.912258] worker_thread+0x4a/0x3c0 This looks like pcr->remap_addr is accessed after it has been iounmap'ed in rtsx_pci_remove() or before it has been iomap'ed in rtsx_pci_probe(). Is the card reader itself located below a hotplug port and unplugged here? Or is this about the card being removed from the card reader? Having full dmesg output and lspci -vvv output attached to a bugzilla would help to understand what is going on. Thanks, Lukas
On Mon, Oct 16, 2023 at 5:32 PM Lukas Wunner <lukas@wunner.de> wrote: > > On Mon, Oct 16, 2023 at 12:01:31PM +0800, Kai-Heng Feng wrote: > > When inserting an SD7.0 card to Realtek card reader, it can trigger PCI > > slot Link down and causes the following error: > > Why does *inserting* a card cause a Link Down? Ricky, do you know the reason why Link Down happens? > > > > [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > [ 63.912118] BUG: unable to handle page fault for address: ffffb24d403e5010 > [...] > > [ 63.912198] ? asm_exc_page_fault+0x27/0x30 > > [ 63.912203] ? ioread32+0x2e/0x70 > > [ 63.912206] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] > > [ 63.912217] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] > > [ 63.912226] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] > > [ 63.912234] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] > > [ 63.912243] ? __pfx_pci_pm_runtime_idle+0x10/0x10 > > [ 63.912246] pci_pm_runtime_idle+0x34/0x70 > > [ 63.912248] rpm_idle+0xc4/0x2b0 > > [ 63.912251] pm_runtime_work+0x93/0xc0 > > [ 63.912254] process_one_work+0x21a/0x430 > > [ 63.912258] worker_thread+0x4a/0x3c0 > > This looks like pcr->remap_addr is accessed after it has been iounmap'ed > in rtsx_pci_remove() or before it has been iomap'ed in rtsx_pci_probe(). > > Is the card reader itself located below a hotplug port and unplugged here? > Or is this about the card being removed from the card reader? > > Having full dmesg output and lspci -vvv output attached to a bugzilla > would help to understand what is going on. I don't have the hardware so we need Ricky to provide more information here. Regardless of the cardreader issue, do you have any concern on the patch itself? Kai-Heng > > Thanks, > > Lukas
> -----Original Message----- > From: Kai-Heng Feng <kai.heng.feng@canonical.com> > > On Mon, Oct 16, 2023 at 5:32 PM Lukas Wunner <lukas@wunner.de> wrote: > > > > On Mon, Oct 16, 2023 at 12:01:31PM +0800, Kai-Heng Feng wrote: > > > When inserting an SD7.0 card to Realtek card reader, it can trigger > > > PCI slot Link down and causes the following error: > > > > Why does *inserting* a card cause a Link Down? > > Ricky, do you know the reason why Link Down happens? > Because SD7.0 card is use pcie-nvme driver, reader need to re-link then just do the pcie channel > > > > > > > [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > > [ 63.912118] BUG: unable to handle page fault for address: > ffffb24d403e5010 > > [...] > > > [ 63.912198] ? asm_exc_page_fault+0x27/0x30 > > > [ 63.912203] ? ioread32+0x2e/0x70 > > > [ 63.912206] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] > > > [ 63.912217] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] > > > [ 63.912226] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] > > > [ 63.912234] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] > > > [ 63.912243] ? __pfx_pci_pm_runtime_idle+0x10/0x10 > > > [ 63.912246] pci_pm_runtime_idle+0x34/0x70 > > > [ 63.912248] rpm_idle+0xc4/0x2b0 > > > [ 63.912251] pm_runtime_work+0x93/0xc0 > > > [ 63.912254] process_one_work+0x21a/0x430 > > > [ 63.912258] worker_thread+0x4a/0x3c0 > > > > This looks like pcr->remap_addr is accessed after it has been > > iounmap'ed in rtsx_pci_remove() or before it has been iomap'ed in > rtsx_pci_probe(). > > > > Is the card reader itself located below a hotplug port and unplugged here? > > Or is this about the card being removed from the card reader? > > > > Having full dmesg output and lspci -vvv output attached to a bugzilla > > would help to understand what is going on. > > I don't have the hardware so we need Ricky to provide more information here. > > Regardless of the cardreader issue, do you have any concern on the patch > itself? > > Kai-Heng > > > > > Thanks, > > > > Lukas
[cc -= unrelated mailing lists bpf, kernel-hardening] On Tue, Oct 17, 2023 at 05:44:13AM +0000, Ricky WU wrote: > > From: Kai-Heng Feng <kai.heng.feng@canonical.com> > > On Mon, Oct 16, 2023 at 5:32???PM Lukas Wunner <lukas@wunner.de> wrote: > > > On Mon, Oct 16, 2023 at 12:01:31PM +0800, Kai-Heng Feng wrote: > > > > When inserting an SD7.0 card to Realtek card reader, it can trigger > > > > PCI slot Link down and causes the following error: > > > > > > Why does *inserting* a card cause a Link Down? > > > > Ricky, do you know the reason why Link Down happens? > > Because SD7.0 card is use pcie-nvme driver, reader need to re-link > then just do the pcie channel I don't quite follow. I don't see a pcie-nvme driver in Linus' current master branch. Which driver are you referring to? What does "re-link" mean? Rebind to a different driver? Thanks, Lukas
[cc -= unrelated mailing lists bpf, kernel-hardening] On Tue, Oct 17, 2023 at 12:35:18PM +0800, Kai-Heng Feng wrote: > On Mon, Oct 16, 2023 at 5:32???PM Lukas Wunner <lukas@wunner.de> wrote: > > On Mon, Oct 16, 2023 at 12:01:31PM +0800, Kai-Heng Feng wrote: > > > [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > > [ 63.912118] BUG: unable to handle page fault for address: ffffb24d403e5010 > > [...] > > > [ 63.912198] ? asm_exc_page_fault+0x27/0x30 > > > [ 63.912203] ? ioread32+0x2e/0x70 > > > [ 63.912206] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] > > > [ 63.912217] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] > > > [ 63.912226] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] > > > [ 63.912234] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] > > > [ 63.912243] ? __pfx_pci_pm_runtime_idle+0x10/0x10 > > > [ 63.912246] pci_pm_runtime_idle+0x34/0x70 > > > [ 63.912248] rpm_idle+0xc4/0x2b0 > > > [ 63.912251] pm_runtime_work+0x93/0xc0 > > > [ 63.912254] process_one_work+0x21a/0x430 > > > [ 63.912258] worker_thread+0x4a/0x3c0 > > > > This looks like pcr->remap_addr is accessed after it has been iounmap'ed > > in rtsx_pci_remove() or before it has been iomap'ed in rtsx_pci_probe(). > > > > Is the card reader itself located below a hotplug port and unplugged here? > > Or is this about the card being removed from the card reader? > > > > Having full dmesg output and lspci -vvv output attached to a bugzilla > > would help to understand what is going on. > > I don't have the hardware so we need Ricky to provide more information here. > > Regardless of the cardreader issue, do you have any concern on the patch > itself? Yes, my concern is that this might be the wrong approach. I would like to understand what is going on, hence my questions above. Thanks, Lukas
> On Mon, Oct 16, 2023 at 12:01:31PM +0800, Kai-Heng Feng wrote: > > When inserting an SD7.0 card to Realtek card reader, it can trigger > > PCI slot Link down and causes the following error: > > Why does *inserting* a card cause a Link Down? > > > > [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > [ 63.912118] BUG: unable to handle page fault for address: > ffffb24d403e5010 > [...] > > [ 63.912198] ? asm_exc_page_fault+0x27/0x30 > > [ 63.912203] ? ioread32+0x2e/0x70 > > [ 63.912206] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] > > [ 63.912217] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] > > [ 63.912226] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] > > [ 63.912234] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] > > [ 63.912243] ? __pfx_pci_pm_runtime_idle+0x10/0x10 > > [ 63.912246] pci_pm_runtime_idle+0x34/0x70 > > [ 63.912248] rpm_idle+0xc4/0x2b0 > > [ 63.912251] pm_runtime_work+0x93/0xc0 > > [ 63.912254] process_one_work+0x21a/0x430 > > [ 63.912258] worker_thread+0x4a/0x3c0 > > This looks like pcr->remap_addr is accessed after it has been iounmap'ed in > rtsx_pci_remove() or before it has been iomap'ed in rtsx_pci_probe(). > > Is the card reader itself located below a hotplug port and unplugged here? Yes it is card reader unplug itself, because sd7.0 card is not used rtsx_pcr, it use nvme driver Ricky > Or is this about the card being removed from the card reader? > > Having full dmesg output and lspci -vvv output attached to a bugzilla would > help to understand what is going on. > > Thanks, > > Lukas
[cc -= unrelated mailing lists bpf, kernel-hardening] On Tue, Oct 17, 2023 at 10:25:39AM +0000, Ricky WU wrote: > > On Mon, Oct 16, 2023 at 12:01:31PM +0800, Kai-Heng Feng wrote: > > > When inserting an SD7.0 card to Realtek card reader, it can trigger > > > PCI slot Link down and causes the following error: > > > > Why does *inserting* a card cause a Link Down? > > > > > > > [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > > [ 63.912118] BUG: unable to handle page fault for address: > > ffffb24d403e5010 > > [...] > > > [ 63.912198] ? asm_exc_page_fault+0x27/0x30 > > > [ 63.912203] ? ioread32+0x2e/0x70 > > > [ 63.912206] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] > > > [ 63.912217] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] > > > [ 63.912226] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] > > > [ 63.912234] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] > > > [ 63.912243] ? __pfx_pci_pm_runtime_idle+0x10/0x10 > > > [ 63.912246] pci_pm_runtime_idle+0x34/0x70 > > > [ 63.912248] rpm_idle+0xc4/0x2b0 > > > [ 63.912251] pm_runtime_work+0x93/0xc0 > > > [ 63.912254] process_one_work+0x21a/0x430 > > > [ 63.912258] worker_thread+0x4a/0x3c0 > > > > This looks like pcr->remap_addr is accessed after it has been iounmap'ed in > > rtsx_pci_remove() or before it has been iomap'ed in rtsx_pci_probe(). > > > > Is the card reader itself located below a hotplug port and unplugged here? > > Yes it is card reader unplug itself, because sd7.0 card is not used > rtsx_pcr, it use nvme driver I can only guess here as the dmesg and lspci output I requested hasn't been provided: I assume that this card reader may contain a PCIe switch with a regular SD card reader below a first Downstream Port (which is hotplug-capable). If an SD express card is inserted, the regular SD card reader disappears from the Downstream Port and the inserted card appears as an NVMe drive (possibly below a second Downstream Port, or below the first Downstream Port). The commit message is somewhat misleading in that it links the unhandled page fault to card insertion. That may be the trigger, but the root cause appears to be that a runtime PM request is performed asynchronously after the SD card reader has iounmap'ed pcr->remap_addr. If that is indeed the root cause (as I suspect), the fix needs to be placed somewhere else. pciehp is only one of several hotplug drivers and fixing this only in pciehp may leave the other hotplug drivers vulnerable to the same issue. Unfortunately the information provided so far is insufficient to recommend a better fix. It would be necessary to debug why the asynchronous RPM request is not canceled even though rtsx_pci_remove() runtime resumes the device before iounmap'ing pcr->remap_addr. Perhaps there's a bug in runtime PM code that causes asynchronous requests to not be canceled upon a pm_runtime_get_sync()? Or perhaps a wmb() is necessary in pci_device_remove() after setting pci_dev->driver = NULL? Thanks, Lukas
Hi Kai-Heng,
kernel test robot noticed the following build warnings:
[auto build test WARNING on pci/next]
[also build test WARNING on pci/for-linus linus/master v6.6-rc6 next-20231017]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch#_base_tree_information]
url: https://github.com/intel-lab-lkp/linux/commits/Kai-Heng-Feng/PCI-pciehp-Prevent-child-devices-from-doing-RPM-on-PCIe-Link-Down/20231017-142208
base: https://git.kernel.org/pub/scm/linux/kernel/git/pci/pci.git next
patch link: https://lore.kernel.org/r/20231016040132.23824-1-kai.heng.feng%40canonical.com
patch subject: [PATCH] PCI: pciehp: Prevent child devices from doing RPM on PCIe Link Down
config: alpha-allyesconfig (https://download.01.org/0day-ci/archive/20231017/202310171955.hlish6FZ-lkp@intel.com/config)
compiler: alpha-linux-gcc (GCC) 13.2.0
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20231017/202310171955.hlish6FZ-lkp@intel.com/reproduce)
If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <yujie.liu@intel.com>
| Closes: https://lore.kernel.org/r/202310171955.hlish6FZ-lkp@intel.com/
All warnings (new ones prefixed by >>):
>> drivers/pci/hotplug/pciehp_pci.c:25:5: warning: no previous prototype for 'pci_dev_disconnect' [-Wmissing-prototypes]
25 | int pci_dev_disconnect(struct pci_dev *pdev, void *unused)
| ^~~~~~~~~~~~~~~~~~
vim +/pci_dev_disconnect +25 drivers/pci/hotplug/pciehp_pci.c
^1da177e4c3f41 Linus Torvalds 2005-04-16 24
2bd1cb5c4e6711 Kai-Heng Feng 2023-10-16 @25 int pci_dev_disconnect(struct pci_dev *pdev, void *unused)
2bd1cb5c4e6711 Kai-Heng Feng 2023-10-16 26 {
2bd1cb5c4e6711 Kai-Heng Feng 2023-10-16 27 pm_runtime_barrier(&pdev->dev);
2bd1cb5c4e6711 Kai-Heng Feng 2023-10-16 28 pci_dev_set_disconnected(pdev, NULL);
2bd1cb5c4e6711 Kai-Heng Feng 2023-10-16 29
2bd1cb5c4e6711 Kai-Heng Feng 2023-10-16 30 return 0;
2bd1cb5c4e6711 Kai-Heng Feng 2023-10-16 31 }
2bd1cb5c4e6711 Kai-Heng Feng 2023-10-16 32
> [cc -= unrelated mailing lists bpf, kernel-hardening] > > On Tue, Oct 17, 2023 at 10:25:39AM +0000, Ricky WU wrote: > > I can only guess here as the dmesg and lspci output I requested hasn't been > provided: > > I assume that this card reader may contain a PCIe switch with a regular SD > card reader below a first Downstream Port (which is hotplug-capable). If an > SD express card is inserted, the regular SD card reader disappears from the > Downstream Port and the inserted card appears as an NVMe drive (possibly > below a second Downstream Port, or below the first Downstream Port). > > The commit message is somewhat misleading in that it links the unhandled > page fault to card insertion. That may be the trigger, but the root cause > appears to be that a runtime PM request is performed asynchronously after > the SD card reader has iounmap'ed > pcr->remap_addr. > > If that is indeed the root cause (as I suspect), the fix needs to be placed > somewhere else. > > pciehp is only one of several hotplug drivers and fixing this only in pciehp may > leave the other hotplug drivers vulnerable to the same issue. > > Unfortunately the information provided so far is insufficient to recommend a > better fix. It would be necessary to debug why the asynchronous RPM > request is not canceled even though rtsx_pci_remove() runtime resumes the > device before iounmap'ing pcr->remap_addr. > Perhaps there's a bug in runtime PM code that causes asynchronous requests > to not be canceled upon a pm_runtime_get_sync()? > Or perhaps a wmb() is necessary in pci_device_remove() after setting > pci_dev->driver = NULL? > > Thanks, > > Lukas Hi Lukas, Sorry for late, the dmesg as below [ 0.000000] microcode: updated early: 0x96 -> 0xf4, date = 2023-02-23 [ 0.000000] Linux version 6.4.0 (root@cr-desktop) (gcc (Ubuntu 9.4.0-1ubuntu1~20.04.2) 9.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #6 SMP PREEMPT_DYNAMIC Wed Aug 30 20:35:48 CST 2023 [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-6.4.0 root=UUID=74fe52d0-e90f-4b0a-92f4-581b5fa98519 ro quiet splash vt.handoff=7 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] Hygon HygonGenuine [ 0.000000] Centaur CentaurHauls [ 0.000000] zhaoxin Shanghai [ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x008: 'MPX bounds registers' [ 0.000000] x86/fpu: Supporting XSAVE feature 0x010: 'MPX CSR' [ 0.000000] x86/fpu: xstate_offset[3]: 576, xstate_sizes[3]: 64 [ 0.000000] x86/fpu: xstate_offset[4]: 640, xstate_sizes[4]: 64 [ 0.000000] x86/fpu: Enabled xstate features 0x1b, context size is 704 bytes, using 'compacted' format. [ 0.000000] signal: max sigframe size: 2032 [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000005efff] usable [ 0.000000] BIOS-e820: [mem 0x000000000005f000-0x000000000005ffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000060000-0x000000000009ffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000000a0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000007c764fff] usable [ 0.000000] BIOS-e820: [mem 0x000000007c765000-0x000000007dfd0fff] reserved [ 0.000000] BIOS-e820: [mem 0x000000007dfd1000-0x000000007e04dfff] ACPI data [ 0.000000] BIOS-e820: [mem 0x000000007e04e000-0x000000007e526fff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x000000007e527000-0x000000007ed0dfff] reserved [ 0.000000] BIOS-e820: [mem 0x000000007ed0e000-0x000000007ed0efff] usable [ 0.000000] BIOS-e820: [mem 0x000000007ed0f000-0x000000008fffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fe000000-0x00000000fe010fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000016dffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] e820: update [mem 0x68808018-0x68818057] usable ==> usable [ 0.000000] e820: update [mem 0x68808018-0x68818057] usable ==> usable [ 0.000000] e820: update [mem 0x687f7018-0x68807e57] usable ==> usable [ 0.000000] e820: update [mem 0x687f7018-0x68807e57] usable ==> usable [ 0.000000] extended physical RAM map: [ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000005efff] usable [ 0.000000] reserve setup_data: [mem 0x000000000005f000-0x000000000005ffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000000060000-0x000000000009ffff] usable [ 0.000000] reserve setup_data: [mem 0x00000000000a0000-0x00000000000fffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x00000000687f7017] usable [ 0.000000] reserve setup_data: [mem 0x00000000687f7018-0x0000000068807e57] usable [ 0.000000] reserve setup_data: [mem 0x0000000068807e58-0x0000000068808017] usable [ 0.000000] reserve setup_data: [mem 0x0000000068808018-0x0000000068818057] usable [ 0.000000] reserve setup_data: [mem 0x0000000068818058-0x000000007c764fff] usable [ 0.000000] reserve setup_data: [mem 0x000000007c765000-0x000000007dfd0fff] reserved [ 0.000000] reserve setup_data: [mem 0x000000007dfd1000-0x000000007e04dfff] ACPI data [ 0.000000] reserve setup_data: [mem 0x000000007e04e000-0x000000007e526fff] ACPI NVS [ 0.000000] reserve setup_data: [mem 0x000000007e527000-0x000000007ed0dfff] reserved [ 0.000000] reserve setup_data: [mem 0x000000007ed0e000-0x000000007ed0efff] usable [ 0.000000] reserve setup_data: [mem 0x000000007ed0f000-0x000000008fffffff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000fe000000-0x00000000fe010fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000fed00000-0x00000000fed03fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] reserve setup_data: [mem 0x00000000ff000000-0x00000000ffffffff] reserved [ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000016dffffff] usable [ 0.000000] efi: EFI v2.7 by American Megatrends [ 0.000000] efi: ACPI 2.0=0x7e468000 ACPI=0x7e468000 TPMFinalLog=0x7e4d1000 SMBIOS=0x7ea7a000 SMBIOS 3.0=0x7ea79000 MEMATTR=0x7955a098 ESRT=0x7adf4118 MOKvar=0x7ea92000 RNG=0x7e04d018 TPMEventLog=0x68819018 [ 0.000000] random: crng init done [ 0.000000] efi: Remove mem45: MMIO range=[0xe0000000-0xefffffff] (256MB) from e820 map [ 0.000000] e820: remove [mem 0xe0000000-0xefffffff] reserved [ 0.000000] efi: Not removing mem46: MMIO range=[0xfe000000-0xfe010fff] (68KB) from e820 map [ 0.000000] efi: Not removing mem47: MMIO range=[0xfec00000-0xfec00fff] (4KB) from e820 map [ 0.000000] efi: Not removing mem48: MMIO range=[0xfed00000-0xfed03fff] (16KB) from e820 map [ 0.000000] efi: Not removing mem49: MMIO range=[0xfee00000-0xfee00fff] (4KB) from e820 map [ 0.000000] efi: Remove mem50: MMIO range=[0xff000000-0xffffffff] (16MB) from e820 map [ 0.000000] e820: remove [mem 0xff000000-0xffffffff] reserved [ 0.000000] SMBIOS 3.1.1 present. [ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./H370M Pro4, BIOS P3.40 10/25/2018 [ 0.000000] tsc: Detected 3700.000 MHz processor [ 0.000000] tsc: Detected 3699.850 MHz TSC [ 0.000602] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000605] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000611] last_pfn = 0x16e000 max_arch_pfn = 0x400000000 [ 0.000615] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT [ 0.000975] last_pfn = 0x7ed0f max_arch_pfn = 0x400000000 [ 0.007022] found SMP MP-table at [mem 0x000fcd30-0x000fcd3f] [ 0.007032] esrt: Reserving ESRT space from 0x000000007adf4118 to 0x000000007adf4150. [ 0.007036] e820: update [mem 0x7adf4000-0x7adf4fff] usable ==> reserved [ 0.007050] Using GB pages for direct mapping [ 0.007209] Secure boot disabled [ 0.007209] RAMDISK: [mem 0x68822000-0x7153ffff] [ 0.007213] ACPI: Early table checksum verification disabled [ 0.007216] ACPI: RSDP 0x000000007E468000 000024 (v02 ALASKA) [ 0.007219] ACPI: XSDT 0x000000007E4680B0 0000DC (v01 ALASKA A M I 01072009 AMI 00010013) [ 0.007224] ACPI: FACP 0x000000007E4A7808 000114 (v06 ALASKA A M I 01072009 AMI 00010013) [ 0.007228] ACPI: DSDT 0x000000007E468220 03F5E6 (v02 ALASKA A M I 01072009 INTL 20160527) [ 0.007231] ACPI: FACS 0x000000007E526080 000040 [ 0.007233] ACPI: APIC 0x000000007E4A7920 000084 (v04 ALASKA A M I 01072009 AMI 00010013) [ 0.007236] ACPI: FPDT 0x000000007E4A79A8 000044 (v01 ALASKA A M I 01072009 AMI 00010013) [ 0.007238] ACPI: FIDT 0x000000007E4A79F0 00009C (v01 ALASKA A M I 01072009 AMI 00010013) [ 0.007241] ACPI: MCFG 0x000000007E4A7A90 00003C (v01 ALASKA A M I 01072009 MSFT 00000097) [ 0.007243] ACPI: SSDT 0x000000007E4A7AD0 000378 (v01 SataRe SataTabl 00001000 INTL 20160527) [ 0.007246] ACPI: SSDT 0x000000007E4A7E48 001B1C (v02 CpuRef CpuSsdt 00003000 INTL 20160527) [ 0.007248] ACPI: AAFT 0x000000007E4A9968 00023D (v01 ALASKA OEMAAFT 01072009 MSFT 00000097) [ 0.007251] ACPI: SSDT 0x000000007E4A9BA8 0031C6 (v02 SaSsdt SaSsdt 00003000 INTL 20160527) [ 0.007253] ACPI: HPET 0x000000007E4ACD70 000038 (v01 ALASKA A M I 00000002 01000013) [ 0.007256] ACPI: SSDT 0x000000007E4ACDA8 001C01 (v02 ALASKA CflS_Rvp 00001000 INTL 20160527) [ 0.007258] ACPI: SSDT 0x000000007E4AE9B0 002950 (v02 INTEL xh_cfsd4 00000000 INTL 20160527) [ 0.007261] ACPI: UEFI 0x000000007E4B1300 000042 (v01 ALASKA A M I 00000002 01000013) [ 0.007263] ACPI: LPIT 0x000000007E4B1348 00005C (v01 ALASKA A M I 00000002 01000013) [ 0.007266] ACPI: SSDT 0x000000007E4B13A8 0014E2 (v02 ALASKA TbtTypeC 00000000 INTL 20160527) [ 0.007268] ACPI: DBGP 0x000000007E4B2890 000034 (v01 ALASKA A M I 00000002 01000013) [ 0.007271] ACPI: DBG2 0x000000007E4B28C8 000054 (v00 ALASKA A M I 00000002 01000013) [ 0.007273] ACPI: SSDT 0x000000007E4B2920 001B67 (v02 ALASKA UsbCTabl 00001000 INTL 20160527) [ 0.007276] ACPI: SSDT 0x000000007E4B4488 000144 (v02 Intel ADebTabl 00001000 INTL 20160527) [ 0.007278] ACPI: DMAR 0x000000007E4B45D0 0000A8 (v01 INTEL EDK2 00000002 01000013) [ 0.007281] ACPI: BGRT 0x000000007E4B4678 000038 (v01 ALASKA A M I 01072009 AMI 00010013) [ 0.007283] ACPI: TPM2 0x000000007E4B46B0 000034 (v04 ALASKA A M I 00000001 AMI 00000000) [ 0.007285] ACPI: WSMT 0x000000007E4B46E8 000028 (v01 ALASKA A M I 01072009 AMI 00010013) [ 0.007288] ACPI: Reserving FACP table memory at [mem 0x7e4a7808-0x7e4a791b] [ 0.007289] ACPI: Reserving DSDT table memory at [mem 0x7e468220-0x7e4a7805] [ 0.007290] ACPI: Reserving FACS table memory at [mem 0x7e526080-0x7e5260bf] [ 0.007290] ACPI: Reserving APIC table memory at [mem 0x7e4a7920-0x7e4a79a3] [ 0.007291] ACPI: Reserving FPDT table memory at [mem 0x7e4a79a8-0x7e4a79eb] [ 0.007292] ACPI: Reserving FIDT table memory at [mem 0x7e4a79f0-0x7e4a7a8b] [ 0.007292] ACPI: Reserving MCFG table memory at [mem 0x7e4a7a90-0x7e4a7acb] [ 0.007293] ACPI: Reserving SSDT table memory at [mem 0x7e4a7ad0-0x7e4a7e47] [ 0.007294] ACPI: Reserving SSDT table memory at [mem 0x7e4a7e48-0x7e4a9963] [ 0.007294] ACPI: Reserving AAFT table memory at [mem 0x7e4a9968-0x7e4a9ba4] [ 0.007295] ACPI: Reserving SSDT table memory at [mem 0x7e4a9ba8-0x7e4acd6d] [ 0.007296] ACPI: Reserving HPET table memory at [mem 0x7e4acd70-0x7e4acda7] [ 0.007296] ACPI: Reserving SSDT table memory at [mem 0x7e4acda8-0x7e4ae9a8] [ 0.007297] ACPI: Reserving SSDT table memory at [mem 0x7e4ae9b0-0x7e4b12ff] [ 0.007297] ACPI: Reserving UEFI table memory at [mem 0x7e4b1300-0x7e4b1341] [ 0.007298] ACPI: Reserving LPIT table memory at [mem 0x7e4b1348-0x7e4b13a3] [ 0.007299] ACPI: Reserving SSDT table memory at [mem 0x7e4b13a8-0x7e4b2889] [ 0.007299] ACPI: Reserving DBGP table memory at [mem 0x7e4b2890-0x7e4b28c3] [ 0.007300] ACPI: Reserving DBG2 table memory at [mem 0x7e4b28c8-0x7e4b291b] [ 0.007301] ACPI: Reserving SSDT table memory at [mem 0x7e4b2920-0x7e4b4486] [ 0.007301] ACPI: Reserving SSDT table memory at [mem 0x7e4b4488-0x7e4b45cb] [ 0.007302] ACPI: Reserving DMAR table memory at [mem 0x7e4b45d0-0x7e4b4677] [ 0.007303] ACPI: Reserving BGRT table memory at [mem 0x7e4b4678-0x7e4b46af] [ 0.007303] ACPI: Reserving TPM2 table memory at [mem 0x7e4b46b0-0x7e4b46e3] [ 0.007304] ACPI: Reserving WSMT table memory at [mem 0x7e4b46e8-0x7e4b470f] [ 0.007625] No NUMA configuration found [ 0.007625] Faking a node at [mem 0x0000000000000000-0x000000016dffffff] [ 0.007632] NODE_DATA(0) allocated [mem 0x16dfd5000-0x16dffffff] [ 0.007775] Zone ranges: [ 0.007776] DMA [mem 0x0000000000001000-0x0000000000ffffff] [ 0.007777] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.007779] Normal [mem 0x0000000100000000-0x000000016dffffff] [ 0.007780] Device empty [ 0.007781] Movable zone start for each node [ 0.007783] Early memory node ranges [ 0.007783] node 0: [mem 0x0000000000001000-0x000000000005efff] [ 0.007784] node 0: [mem 0x0000000000060000-0x000000000009ffff] [ 0.007785] node 0: [mem 0x0000000000100000-0x000000007c764fff] [ 0.007786] node 0: [mem 0x000000007ed0e000-0x000000007ed0efff] [ 0.007787] node 0: [mem 0x0000000100000000-0x000000016dffffff] [ 0.007788] Initmem setup node 0 [mem 0x0000000000001000-0x000000016dffffff] [ 0.007791] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.007792] On node 0, zone DMA: 1 pages in unavailable ranges [ 0.007812] On node 0, zone DMA: 96 pages in unavailable ranges [ 0.012369] On node 0, zone DMA32: 9641 pages in unavailable ranges [ 0.016537] On node 0, zone Normal: 4849 pages in unavailable ranges [ 0.016610] On node 0, zone Normal: 8192 pages in unavailable ranges [ 0.016626] Reserving Intel graphics memory at [mem 0x80000000-0x8fffffff] [ 0.017053] ACPI: PM-Timer IO Port: 0x1808 [ 0.017058] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.017060] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) [ 0.017060] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) [ 0.017061] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) [ 0.017125] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 [ 0.017127] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.017129] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.017132] ACPI: Using ACPI (MADT) for SMP configuration information [ 0.017133] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.017138] e820: update [mem 0x78a54000-0x78a94fff] usable ==> reserved [ 0.017147] TSC deadline timer available [ 0.017148] smpboot: Allowing 4 CPUs, 0 hotplug CPUs [ 0.017160] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.017161] PM: hibernation: Registered nosave memory: [mem 0x0005f000-0x0005ffff] [ 0.017163] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000fffff] [ 0.017164] PM: hibernation: Registered nosave memory: [mem 0x687f7000-0x687f7fff] [ 0.017165] PM: hibernation: Registered nosave memory: [mem 0x68807000-0x68807fff] [ 0.017166] PM: hibernation: Registered nosave memory: [mem 0x68808000-0x68808fff] [ 0.017167] PM: hibernation: Registered nosave memory: [mem 0x68818000-0x68818fff] [ 0.017168] PM: hibernation: Registered nosave memory: [mem 0x78a54000-0x78a94fff] [ 0.017170] PM: hibernation: Registered nosave memory: [mem 0x7adf4000-0x7adf4fff] [ 0.017171] PM: hibernation: Registered nosave memory: [mem 0x7c765000-0x7dfd0fff] [ 0.017171] PM: hibernation: Registered nosave memory: [mem 0x7dfd1000-0x7e04dfff] [ 0.017172] PM: hibernation: Registered nosave memory: [mem 0x7e04e000-0x7e526fff] [ 0.017172] PM: hibernation: Registered nosave memory: [mem 0x7e527000-0x7ed0dfff] [ 0.017174] PM: hibernation: Registered nosave memory: [mem 0x7ed0f000-0x8fffffff] [ 0.017174] PM: hibernation: Registered nosave memory: [mem 0x90000000-0xfdffffff] [ 0.017175] PM: hibernation: Registered nosave memory: [mem 0xfe000000-0xfe010fff] [ 0.017175] PM: hibernation: Registered nosave memory: [mem 0xfe011000-0xfebfffff] [ 0.017176] PM: hibernation: Registered nosave memory: [mem 0xfec00000-0xfec00fff] [ 0.017177] PM: hibernation: Registered nosave memory: [mem 0xfec01000-0xfecfffff] [ 0.017177] PM: hibernation: Registered nosave memory: [mem 0xfed00000-0xfed03fff] [ 0.017178] PM: hibernation: Registered nosave memory: [mem 0xfed04000-0xfedfffff] [ 0.017178] PM: hibernation: Registered nosave memory: [mem 0xfee00000-0xfee00fff] [ 0.017179] PM: hibernation: Registered nosave memory: [mem 0xfee01000-0xffffffff] [ 0.017180] [mem 0x90000000-0xfdffffff] available for PCI devices [ 0.017181] Booting paravirtualized kernel on bare hardware [ 0.017183] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns [ 0.017188] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1 [ 0.017641] percpu: Embedded 62 pages/cpu s217088 r8192 d28672 u524288 [ 0.017647] pcpu-alloc: s217088 r8192 d28672 u524288 alloc=1*2097152 [ 0.017649] pcpu-alloc: [0] 0 1 2 3 [ 0.017667] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-6.4.0 root=UUID=74fe52d0-e90f-4b0a-92f4-581b5fa98519 ro quiet splash vt.handoff=7 [ 0.017736] Unknown kernel command line parameters "splash BOOT_IMAGE=/boot/vmlinuz-6.4.0", will be passed to user space. [ 0.018341] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.018622] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear) [ 0.018673] Fallback order for Node 0: 0 [ 0.018675] Built 1 zonelists, mobility grouping on. Total pages: 945096 [ 0.018676] Policy zone: Normal [ 0.018680] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.018686] software IO TLB: area num 4. [ 0.047991] Memory: 3457148K/3841040K available (18432K kernel code, 3203K rwdata, 6968K rodata, 4432K init, 16780K bss, 383632K reserved, 0K cma-reserved) [ 0.048089] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.048098] Kernel/User page tables isolation: enabled [ 0.048126] ftrace: allocating 52011 entries in 204 pages [ 0.055493] ftrace: allocated 204 pages with 4 groups [ 0.056091] Dynamic Preempt: voluntary [ 0.056112] rcu: Preemptible hierarchical RCU implementation. [ 0.056113] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=4. [ 0.056114] Trampoline variant of Tasks RCU enabled. [ 0.056114] Rude variant of Tasks RCU enabled. [ 0.056115] Tracing variant of Tasks RCU enabled. [ 0.056115] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.056116] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.058547] NR_IRQS: 524544, nr_irqs: 1024, preallocated irqs: 16 [ 0.058808] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.059150] Console: colour dummy device 80x25 [ 0.059152] printk: console [tty0] enabled [ 0.059192] ACPI: Core revision 20230331 [ 0.059542] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635855245 ns [ 0.059685] APIC: Switch to symmetric I/O mode setup [ 0.059687] DMAR: Host address width 39 [ 0.059688] DMAR: DRHD base: 0x000000fed90000 flags: 0x0 [ 0.059693] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e [ 0.059695] DMAR: DRHD base: 0x000000fed91000 flags: 0x1 [ 0.059698] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da [ 0.059699] DMAR: RMRR base: 0x0000007e809000 end: 0x0000007ea52fff [ 0.059701] DMAR: RMRR base: 0x0000007f800000 end: 0x0000008fffffff [ 0.059702] DMAR-IR: IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 1 [ 0.059704] DMAR-IR: HPET id 0 under DRHD base 0xfed91000 [ 0.059704] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping. [ 0.063135] DMAR-IR: Enabled IRQ remapping in x2apic mode [ 0.063137] x2apic enabled [ 0.063159] Switched APIC routing to cluster x2apic. [ 0.072497] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.091603] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x6aa99074b1c, max_idle_ns: 881590506587 ns [ 0.091608] Calibrating delay loop (skipped), value calculated using timer frequency.. 7399.70 BogoMIPS (lpj=14799400) [ 0.091611] pid_max: default: 32768 minimum: 301 [ 0.093745] LSM: initializing lsm=lockdown,capability,yama,apparmor,integrity [ 0.093752] Yama: becoming mindful. [ 0.093775] AppArmor: AppArmor initialized [ 0.093806] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.093815] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.093998] x86/cpu: SGX disabled by BIOS. [ 0.094005] CPU0: Thermal monitoring enabled (TM1) [ 0.094039] process: using mwait in idle threads [ 0.094042] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8 [ 0.094043] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4 [ 0.094047] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization [ 0.094049] Spectre V2 : Mitigation: IBRS [ 0.094049] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch [ 0.094050] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on VMEXIT [ 0.094051] RETBleed: Mitigation: IBRS [ 0.094052] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier [ 0.094053] Spectre V2 : User space: Mitigation: STIBP via prctl [ 0.094054] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl [ 0.094060] MDS: Mitigation: Clear CPU buffers [ 0.094061] MMIO Stale Data: Mitigation: Clear CPU buffers [ 0.094065] SRBDS: Mitigation: Microcode [ 0.113482] Freeing SMP alternatives memory: 40K [ 0.113771] smpboot: CPU0: Intel(R) Pentium(R) Gold G5400 CPU @ 3.70GHz (family: 0x6, model: 0x9e, stepping: 0xa) [ 0.113889] cblist_init_generic: Setting adjustable number of callback queues. [ 0.113891] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.113905] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.113916] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.113926] Performance Events: PEBS fmt3+, Skylake events, 32-deep LBR, full-width counters, Intel PMU driver. [ 0.113950] ... version: 4 [ 0.113951] ... bit width: 48 [ 0.113951] ... generic registers: 4 [ 0.113952] ... value mask: 0000ffffffffffff [ 0.113953] ... max period: 00007fffffffffff [ 0.113954] ... fixed-purpose events: 3 [ 0.113954] ... event mask: 000000070000000f [ 0.114070] Estimated ratio of average max frequency by base frequency (times 1024): 1024 [ 0.114090] rcu: Hierarchical SRCU implementation. [ 0.114093] rcu: Max phase no-delay instances is 1000. [ 0.114531] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter. [ 0.114590] smp: Bringing up secondary CPUs ... [ 0.114675] x86: Booting SMP configuration: [ 0.114676] .... node #0, CPUs: #1 #2 [ 0.115687] MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/mds.html for more details. [ 0.115687] MMIO Stale Data CPU bug present and SMT on, data leak possible. See https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/processor_mmio_stale_data.html for more details. [ 0.115726] #3 [ 0.115994] smp: Brought up 1 node, 4 CPUs [ 0.115994] smpboot: Max logical packages: 1 [ 0.115994] smpboot: Total of 4 processors activated (29598.80 BogoMIPS) [ 0.117300] devtmpfs: initialized [ 0.117300] x86/mm: Memory block size: 128MB [ 0.117300] ACPI: PM: Registering ACPI NVS region [mem 0x7e04e000-0x7e526fff] (5083136 bytes) [ 0.117300] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.117300] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.117300] pinctrl core: initialized pinctrl subsystem [ 0.117300] PM: RTC time: 17:02:18, date: 2097-08-22 [ 0.117300] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.119628] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations [ 0.119661] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.119692] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.119702] audit: initializing netlink subsys (disabled) [ 0.119713] audit: type=2000 audit(4028029338.052:1): state=initialized audit_enabled=0 res=1 [ 0.119745] thermal_sys: Registered thermal governor 'fair_share' [ 0.119746] thermal_sys: Registered thermal governor 'bang_bang' [ 0.119747] thermal_sys: Registered thermal governor 'step_wise' [ 0.119748] thermal_sys: Registered thermal governor 'user_space' [ 0.119748] thermal_sys: Registered thermal governor 'power_allocator' [ 0.119756] EISA bus registered [ 0.119765] cpuidle: using governor ladder [ 0.119768] cpuidle: using governor menu [ 0.119813] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.119813] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.119813] PCI: not using MMCONFIG [ 0.119813] PCI: Using configuration type 1 for base access [ 0.119895] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.119901] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. [ 0.119901] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages [ 0.119901] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page [ 0.119901] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages [ 0.119901] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page [ 0.119901] fbcon: Taking over console [ 0.119901] ACPI: Added _OSI(Module Device) [ 0.119901] ACPI: Added _OSI(Processor Device) [ 0.119901] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.119901] ACPI: Added _OSI(Processor Aggregator Device) [ 0.197478] ACPI: 9 ACPI AML tables successfully acquired and loaded [ 0.205812] ACPI: Dynamic OEM Table Load: [ 0.205818] ACPI: SSDT 0xFFFF9074C0D01300 0000F4 (v02 PmRef Cpu0Psd 00003000 INTL 20160527) [ 0.207381] ACPI: \_SB_.PR00: _OSC native thermal LVT Acked [ 0.209303] ACPI: Dynamic OEM Table Load: [ 0.209309] ACPI: SSDT 0xFFFF9074C1225C00 000400 (v02 PmRef Cpu0Cst 00003001 INTL 20160527) [ 0.211047] ACPI: Dynamic OEM Table Load: [ 0.211052] ACPI: SSDT 0xFFFF9074C1276000 0006CB (v02 PmRef Cpu0Ist 00003000 INTL 20160527) [ 0.213253] ACPI: Dynamic OEM Table Load: [ 0.213258] ACPI: SSDT 0xFFFF9074C1277800 0005FC (v02 PmRef ApIst 00003000 INTL 20160527) [ 0.215224] ACPI: Dynamic OEM Table Load: [ 0.215230] ACPI: SSDT 0xFFFF9074C1264000 000AB0 (v02 PmRef ApPsd 00003000 INTL 20160527) [ 0.217635] ACPI: Dynamic OEM Table Load: [ 0.217640] ACPI: SSDT 0xFFFF9074C1224C00 00030A (v02 PmRef ApCst 00003000 INTL 20160527) [ 0.222682] ACPI: Interpreter enabled [ 0.222716] ACPI: PM: (supports S0 S3 S4 S5) [ 0.222717] ACPI: Using IOAPIC for interrupt routing [ 0.222825] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.224645] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved as ACPI motherboard resource [ 0.224660] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.224661] PCI: Using E820 reservations for host bridge windows [ 0.226114] ACPI: Enabled 9 GPEs in block 00 to 7F [ 0.241818] ACPI: \_SB_.PCI0.XDCI.USBC: New power resource [ 0.242002] ACPI: \_SB_.PCI0.PAUD: New power resource [ 0.245815] ACPI: \SPR2: New power resource [ 0.246159] ACPI: \_SB_.PCI0.SAT0.VOL0.V0PR: New power resource [ 0.246595] ACPI: \_SB_.PCI0.SAT0.VOL1.V1PR: New power resource [ 0.247026] ACPI: \_SB_.PCI0.SAT0.VOL2.V2PR: New power resource [ 0.249905] ACPI: \_SB_.PCI0.I2C1.PXTC: New power resource [ 0.253671] ACPI: \_SB_.PCI0.CNVW.WRST: New power resource [ 0.257923] ACPI: \PIN_: New power resource [ 0.258121] ACPI: \SPR0: New power resource [ 0.258182] ACPI: \SPR1: New power resource [ 0.258247] ACPI: \SPR3: New power resource [ 0.258307] ACPI: \SPR5: New power resource [ 0.258651] ACPI: \ZPDR: New power resource [ 0.259131] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) [ 0.259138] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3] [ 0.262396] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug SHPCHotplug PME AER PCIeCapability LTR] [ 0.263902] PCI host bridge to bus 0000:00 [ 0.263905] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] [ 0.263907] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] [ 0.263908] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] [ 0.263910] pci_bus 0000:00: root bus resource [mem 0x90000000-0xdfffffff window] [ 0.263911] pci_bus 0000:00: root bus resource [mem 0xfc800000-0xfe7fffff window] [ 0.263912] pci_bus 0000:00: root bus resource [bus 00-fe] [ 0.264003] pci 0000:00:00.0: [8086:3e0f] type 00 class 0x060000 [ 0.264087] pci 0000:00:02.0: [8086:3e90] type 00 class 0x030000 [ 0.264094] pci 0000:00:02.0: reg 0x10: [mem 0xa2000000-0xa2ffffff 64bit] [ 0.264099] pci 0000:00:02.0: reg 0x18: [mem 0x90000000-0x9fffffff 64bit pref] [ 0.264103] pci 0000:00:02.0: reg 0x20: [io 0x5000-0x503f] [ 0.264116] pci 0000:00:02.0: BAR 2: assigned to efifb [ 0.264119] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] [ 0.264468] pci 0000:00:12.0: [8086:a379] type 00 class 0x118000 [ 0.264494] pci 0000:00:12.0: reg 0x10: [mem 0xa453d000-0xa453dfff 64bit] [ 0.264726] pci 0000:00:14.0: [8086:a36d] type 00 class 0x0c0330 [ 0.264753] pci 0000:00:14.0: reg 0x10: [mem 0xa4520000-0xa452ffff 64bit] [ 0.264855] pci 0000:00:14.0: PME# supported from D3hot D3cold [ 0.266303] pci 0000:00:14.2: [8086:a36f] type 00 class 0x050000 [ 0.266326] pci 0000:00:14.2: reg 0x10: [mem 0xa4536000-0xa4537fff 64bit] [ 0.266340] pci 0000:00:14.2: reg 0x18: [mem 0xa453c000-0xa453cfff 64bit] [ 0.266509] pci 0000:00:16.0: [8086:a360] type 00 class 0x078000 [ 0.266532] pci 0000:00:16.0: reg 0x10: [mem 0xa453b000-0xa453bfff 64bit] [ 0.266619] pci 0000:00:16.0: PME# supported from D3hot [ 0.267122] pci 0000:00:17.0: [8086:a352] type 00 class 0x010601 [ 0.267143] pci 0000:00:17.0: reg 0x10: [mem 0xa4534000-0xa4535fff] [ 0.267154] pci 0000:00:17.0: reg 0x14: [mem 0xa453a000-0xa453a0ff] [ 0.267166] pci 0000:00:17.0: reg 0x18: [io 0x5090-0x5097] [ 0.267177] pci 0000:00:17.0: reg 0x1c: [io 0x5080-0x5083] [ 0.267188] pci 0000:00:17.0: reg 0x20: [io 0x5060-0x507f] [ 0.267199] pci 0000:00:17.0: reg 0x24: [mem 0xa4539000-0xa45397ff] [ 0.267260] pci 0000:00:17.0: PME# supported from D3hot [ 0.267813] pci 0000:00:1c.0: [8086:a33c] type 01 class 0x060400 [ 0.267964] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.268007] pci 0000:00:1c.0: PTM enabled (root), 4ns granularity [ 0.268725] pci 0000:00:1d.0: [8086:a330] type 01 class 0x060400 [ 0.268864] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 0.269548] pci 0000:00:1d.3: [8086:a333] type 01 class 0x060400 [ 0.269712] pci 0000:00:1d.3: PME# supported from D0 D3hot D3cold [ 0.269758] pci 0000:00:1d.3: PTM enabled (root), 4ns granularity [ 0.270453] pci 0000:00:1f.0: [8086:a304] type 00 class 0x060100 [ 0.270985] pci 0000:00:1f.3: [8086:a348] type 00 class 0x040300 [ 0.271043] pci 0000:00:1f.3: reg 0x10: [mem 0xa4530000-0xa4533fff 64bit] [ 0.271128] pci 0000:00:1f.3: reg 0x20: [mem 0xa3000000-0xa30fffff 64bit] [ 0.271267] pci 0000:00:1f.3: PME# supported from D3hot D3cold [ 0.274038] pci 0000:00:1f.4: [8086:a323] type 00 class 0x0c0500 [ 0.274111] pci 0000:00:1f.4: reg 0x10: [mem 0xa4538000-0xa45380ff 64bit] [ 0.274192] pci 0000:00:1f.4: reg 0x20: [io 0xefa0-0xefbf] [ 0.274499] pci 0000:00:1f.5: [8086:a324] type 00 class 0x0c8000 [ 0.274519] pci 0000:00:1f.5: reg 0x10: [mem 0xfe010000-0xfe010fff] [ 0.274685] pci 0000:00:1f.6: [8086:15bc] type 00 class 0x020000 [ 0.274729] pci 0000:00:1f.6: reg 0x10: [mem 0xa4500000-0xa451ffff] [ 0.274963] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold [ 0.275241] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 [ 0.275315] pci 0000:01:00.0: reg 0x10: [mem 0xa3b00000-0xa3b00fff] [ 0.275782] pci 0000:01:00.0: supports D1 D2 [ 0.275784] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold [ 0.276490] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.276494] pci 0000:00:1c.0: bridge window [io 0x4000-0x4fff] [ 0.276499] pci 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] [ 0.276506] pci 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] [ 0.276606] acpiphp: Slot [1] registered [ 0.276616] pci 0000:00:1d.0: PCI bridge to [bus 02] [ 0.276719] pci 0000:00:1d.3: PCI bridge to [bus 03] [ 0.276723] pci 0000:00:1d.3: bridge window [io 0x3000-0x3fff] [ 0.276728] pci 0000:00:1d.3: bridge window [mem 0xa3100000-0xa3afffff] [ 0.276735] pci 0000:00:1d.3: bridge window [mem 0xa0000000-0xa09fffff 64bit pref] [ 0.278108] ACPI: PCI: Interrupt link LNKA configured for IRQ 0 [ 0.278190] ACPI: PCI: Interrupt link LNKB configured for IRQ 1 [ 0.278271] ACPI: PCI: Interrupt link LNKC configured for IRQ 0 [ 0.278352] ACPI: PCI: Interrupt link LNKD configured for IRQ 0 [ 0.278432] ACPI: PCI: Interrupt link LNKE configured for IRQ 0 [ 0.278512] ACPI: PCI: Interrupt link LNKF configured for IRQ 0 [ 0.278593] ACPI: PCI: Interrupt link LNKG configured for IRQ 0 [ 0.278673] ACPI: PCI: Interrupt link LNKH configured for IRQ 0 [ 0.288341] iommu: Default domain type: Translated [ 0.288341] iommu: DMA domain TLB invalidation policy: lazy mode [ 0.288341] SCSI subsystem initialized [ 0.288341] libata version 3.00 loaded. [ 0.288341] ACPI: bus type USB registered [ 0.288341] usbcore: registered new interface driver usbfs [ 0.288341] usbcore: registered new interface driver hub [ 0.288341] usbcore: registered new device driver usb [ 0.288341] pps_core: LinuxPPS API ver. 1 registered [ 0.288341] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.288341] PTP clock support registered [ 0.288341] EDAC MC: Ver: 3.0.0 [ 0.288341] efivars: Registered efivars operations [ 0.288341] NetLabel: Initializing [ 0.288341] NetLabel: domain hash size = 128 [ 0.288341] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.288341] NetLabel: unlabeled traffic allowed by default [ 0.288341] PCI: Using ACPI for IRQ routing [ 0.368970] PCI: pci_cache_line_size set to 64 bytes [ 0.369055] e820: reserve RAM buffer [mem 0x0005f000-0x0005ffff] [ 0.369057] e820: reserve RAM buffer [mem 0x687f7018-0x6bffffff] [ 0.369058] e820: reserve RAM buffer [mem 0x68808018-0x6bffffff] [ 0.369059] e820: reserve RAM buffer [mem 0x78a54000-0x7bffffff] [ 0.369060] e820: reserve RAM buffer [mem 0x7adf4000-0x7bffffff] [ 0.369061] e820: reserve RAM buffer [mem 0x7c765000-0x7fffffff] [ 0.369062] e820: reserve RAM buffer [mem 0x7ed0f000-0x7fffffff] [ 0.369063] e820: reserve RAM buffer [mem 0x16e000000-0x16fffffff] [ 0.371615] pci 0000:00:02.0: vgaarb: setting as boot VGA device [ 0.371615] pci 0000:00:02.0: vgaarb: bridge control possible [ 0.371616] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none [ 0.371621] vgaarb: loaded [ 0.372806] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0 [ 0.372813] hpet0: 8 comparators, 64-bit 24.000000 MHz counter [ 0.375634] clocksource: Switched to clocksource tsc-early [ 0.375733] VFS: Disk quotas dquot_6.6.0 [ 0.375745] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.375859] AppArmor: AppArmor Filesystem Enabled [ 0.375881] pnp: PnP ACPI init [ 0.376221] system 00:00: [io 0x0280-0x028f] has been reserved [ 0.376224] system 00:00: [io 0x0290-0x029f] has been reserved [ 0.376226] system 00:00: [io 0x02a0-0x02af] has been reserved [ 0.376227] system 00:00: [io 0x02b0-0x02bf] has been reserved [ 0.376606] pnp 00:01: [dma 0 disabled] [ 0.376750] system 00:02: [io 0x0680-0x069f] has been reserved [ 0.376752] system 00:02: [io 0x164e-0x164f] has been reserved [ 0.376872] system 00:03: [io 0x1854-0x1857] has been reserved [ 0.377096] system 00:04: [mem 0xfed10000-0xfed17fff] has been reserved [ 0.377098] system 00:04: [mem 0xfed18000-0xfed18fff] has been reserved [ 0.377099] system 00:04: [mem 0xfed19000-0xfed19fff] has been reserved [ 0.377101] system 00:04: [mem 0xe0000000-0xefffffff] has been reserved [ 0.377102] system 00:04: [mem 0xfed20000-0xfed3ffff] has been reserved [ 0.377104] system 00:04: [mem 0xfed90000-0xfed93fff] could not be reserved [ 0.377105] system 00:04: [mem 0xfed45000-0xfed8ffff] has been reserved [ 0.377107] system 00:04: [mem 0xfee00000-0xfeefffff] could not be reserved [ 0.377317] system 00:05: [io 0x1800-0x18fe] could not be reserved [ 0.377320] system 00:05: [mem 0xfd000000-0xfd69ffff] has been reserved [ 0.377321] system 00:05: [mem 0xfd6c0000-0xfd6cffff] has been reserved [ 0.377322] system 00:05: [mem 0xfd6f0000-0xfdffffff] has been reserved [ 0.377324] system 00:05: [mem 0xfe000000-0xfe01ffff] could not be reserved [ 0.377325] system 00:05: [mem 0xfe200000-0xfe7fffff] has been reserved [ 0.377327] system 00:05: [mem 0xff000000-0xffffffff] has been reserved [ 0.377609] system 00:06: [io 0x2000-0x20fe] has been reserved [ 0.377902] system 00:07: [mem 0xfd6e0000-0xfd6effff] has been reserved [ 0.377904] system 00:07: [mem 0xfd6d0000-0xfd6dffff] has been reserved [ 0.377905] system 00:07: [mem 0xfd6b0000-0xfd6bffff] has been reserved [ 0.377907] system 00:07: [mem 0xfd6a0000-0xfd6affff] has been reserved [ 0.379872] pnp: PnP ACPI: found 9 devices [ 0.385811] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns [ 0.385883] NET: Registered PF_INET protocol family [ 0.385953] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.386745] tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.386772] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.386803] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.386948] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear) [ 0.387039] TCP: Hash tables configured (established 32768 bind 32768) [ 0.387099] MPTCP token hash table entries: 4096 (order: 4, 98304 bytes, linear) [ 0.387114] UDP hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 0.387124] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes, linear) [ 0.387159] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.387164] NET: Registered PF_XDP protocol family [ 0.387178] pci 0000:00:1c.0: PCI bridge to [bus 01] [ 0.387187] pci 0000:00:1c.0: bridge window [io 0x4000-0x4fff] [ 0.387193] pci 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] [ 0.387197] pci 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] [ 0.387204] pci 0000:00:1d.0: PCI bridge to [bus 02] [ 0.387219] pci 0000:00:1d.3: PCI bridge to [bus 03] [ 0.387221] pci 0000:00:1d.3: bridge window [io 0x3000-0x3fff] [ 0.387227] pci 0000:00:1d.3: bridge window [mem 0xa3100000-0xa3afffff] [ 0.387231] pci 0000:00:1d.3: bridge window [mem 0xa0000000-0xa09fffff 64bit pref] [ 0.387238] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] [ 0.387240] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] [ 0.387241] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] [ 0.387243] pci_bus 0000:00: resource 7 [mem 0x90000000-0xdfffffff window] [ 0.387244] pci_bus 0000:00: resource 8 [mem 0xfc800000-0xfe7fffff window] [ 0.387245] pci_bus 0000:01: resource 0 [io 0x4000-0x4fff] [ 0.387247] pci_bus 0000:01: resource 1 [mem 0xa3b00000-0xa44fffff] [ 0.387248] pci_bus 0000:01: resource 2 [mem 0xa0a00000-0xa13fffff 64bit pref] [ 0.387249] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff] [ 0.387251] pci_bus 0000:03: resource 1 [mem 0xa3100000-0xa3afffff] [ 0.387252] pci_bus 0000:03: resource 2 [mem 0xa0000000-0xa09fffff 64bit pref] [ 0.388247] PCI: CLS 64 bytes, default 64 [ 0.388264] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.388265] software IO TLB: mapped [mem 0x0000000074a54000-0x0000000078a54000] (64MB) [ 0.388305] Trying to unpack rootfs image as initramfs... [ 0.388462] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.388894] Initialise system trusted keyrings [ 0.388901] Key type blacklist registered [ 0.388950] workingset: timestamp_bits=36 max_order=20 bucket_order=0 [ 0.388968] zbud: loaded [ 0.389152] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.389225] fuse: init (API version 7.38) [ 0.389341] integrity: Platform Keyring initialized [ 0.395426] Key type asymmetric registered [ 0.395430] Asymmetric key parser 'x509' registered [ 0.395455] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243) [ 0.395523] io scheduler mq-deadline registered [ 0.395968] pcieport 0000:00:1c.0: PME: Signaling with IRQ 122 [ 0.396009] pcieport 0000:00:1c.0: pciehp: Slot #8 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+ [ 0.396235] pcieport 0000:00:1d.0: PME: Signaling with IRQ 123 [ 0.396536] pcieport 0000:00:1d.3: PME: Signaling with IRQ 124 [ 0.396563] pcieport 0000:00:1d.3: pciehp: Slot #15 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+ [ 0.396730] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 0.397270] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0 [ 0.397293] ACPI: button: Sleep Button [SLPB] [ 0.397325] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1 [ 0.397341] ACPI: button: Power Button [PWRB] [ 0.397371] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 0.397403] ACPI: button: Power Button [PWRF] [ 0.397978] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.419972] 00:01: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 0.423779] Linux agpgart interface v0.103 [ 0.437969] loop: module loaded [ 0.438340] tun: Universal TUN/TAP device driver, 1.6 [ 0.438408] PPP generic driver version 2.4.2 [ 0.438623] VFIO - User Level meta-driver version: 0.3 [ 0.438757] i8042: PNP: No PS/2 controller found. [ 0.438877] mousedev: PS/2 mouse device common for all mice [ 0.439018] rtc_cmos rtc_cmos: RTC can wake from S4 [ 0.440618] rtc_cmos rtc_cmos: registered as rtc0 [ 0.440930] rtc_cmos rtc_cmos: setting system clock to 2097-08-22T17:02:18 UTC (4028029338) [ 0.440967] rtc_cmos rtc_cmos: alarms up to one month, y3k, 114 bytes nvram [ 0.440979] i2c_dev: i2c /dev entries driver [ 0.441050] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. [ 0.441064] device-mapper: uevent: version 1.0.3 [ 0.441112] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 0.441142] platform eisa.0: Probing EISA bus 0 [ 0.441145] platform eisa.0: EISA: Cannot allocate resource for mainboard [ 0.441147] platform eisa.0: Cannot allocate resource for EISA slot 1 [ 0.441149] platform eisa.0: Cannot allocate resource for EISA slot 2 [ 0.441151] platform eisa.0: Cannot allocate resource for EISA slot 3 [ 0.441152] platform eisa.0: Cannot allocate resource for EISA slot 4 [ 0.441154] platform eisa.0: Cannot allocate resource for EISA slot 5 [ 0.441156] platform eisa.0: Cannot allocate resource for EISA slot 6 [ 0.441157] platform eisa.0: Cannot allocate resource for EISA slot 7 [ 0.441159] platform eisa.0: Cannot allocate resource for EISA slot 8 [ 0.441160] platform eisa.0: EISA: Detected 0 cards [ 0.441163] intel_pstate: Intel P-state driver initializing [ 0.441425] intel_pstate: Disabling energy efficiency optimization [ 0.441426] intel_pstate: HWP enabled [ 0.444231] ledtrig-cpu: registered to indicate activity on CPUs [ 0.444273] efifb: probing for efifb [ 0.444299] efifb: showing boot graphics [ 0.445232] efifb: framebuffer at 0x90000000, using 8100k, total 8100k [ 0.445235] efifb: mode is 1920x1080x32, linelength=7680, pages=1 [ 0.445236] efifb: scrolling: redraw [ 0.445237] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0 [ 0.445378] Console: switching to colour frame buffer device 240x67 [ 0.447308] fb0: EFI VGA frame buffer device [ 0.447448] intel_pmc_core INT33A1:00: initialized [ 0.447619] drop_monitor: Initializing network drop monitor service [ 0.447729] NET: Registered PF_INET6 protocol family [ 0.752379] Freeing initrd memory: 144504K [ 0.758893] Segment Routing with IPv6 [ 0.758908] In-situ OAM (IOAM) with IPv6 [ 0.758935] NET: Registered PF_PACKET protocol family [ 0.759034] Key type dns_resolver registered [ 0.759500] microcode: Microcode Update Driver: v2.2. [ 0.759506] IPI shorthand broadcast: enabled [ 0.761201] sched_clock: Marking stable (752002498, 8487670)->(763339334, -2849166) [ 0.761362] registered taskstats version 1 [ 0.761448] Loading compiled-in X.509 certificates [ 0.761960] Loaded X.509 cert 'Build time autogenerated kernel key: 417a18f9c0ec7ef9b042b8731fef1cec608b3690' [ 0.764147] Key type .fscrypt registered [ 0.764148] Key type fscrypt-provisioning registered [ 0.764254] Key type trusted registered [ 0.767319] Key type encrypted registered [ 0.767323] AppArmor: AppArmor sha1 policy hashing enabled [ 0.768294] integrity: Loading X.509 certificate: UEFI:db [ 0.768321] integrity: Loaded X.509 cert 'Microsoft Corporation UEFI CA 2011: 13adbf4309bd82709c8cd54f316ed522988a1bd4' [ 0.768322] integrity: Loading X.509 certificate: UEFI:db [ 0.768338] integrity: Loaded X.509 cert 'Microsoft Windows Production PCA 2011: a92902398e16c49778cd90f99e4f9ae17c55af53' [ 0.769080] Loading compiled-in module X.509 certificates [ 0.769496] Loaded X.509 cert 'Build time autogenerated kernel key: 417a18f9c0ec7ef9b042b8731fef1cec608b3690' [ 0.769498] ima: Allocated hash algorithm: sha1 [ 0.798364] ima: No architecture policies found [ 0.798409] evm: Initialising EVM extended attributes: [ 0.798413] evm: security.selinux [ 0.798418] evm: security.SMACK64 [ 0.798422] evm: security.SMACK64EXEC [ 0.798425] evm: security.SMACK64TRANSMUTE [ 0.798429] evm: security.SMACK64MMAP [ 0.798431] evm: security.apparmor [ 0.798434] evm: security.ima [ 0.798437] evm: security.capability [ 0.798441] evm: HMAC attrs: 0x1 [ 0.799410] PM: Magic number: 13:435:37 [ 0.799431] bdi 7:2: hash matches [ 0.800077] RAS: Correctable Errors collector initialized. [ 0.800145] clk: Disabling unused clocks [ 0.803806] Freeing unused decrypted memory: 2036K [ 0.805692] Freeing unused kernel image (initmem) memory: 4432K [ 0.824569] Write protecting the kernel read-only data: 26624k [ 0.825870] Freeing unused kernel image (rodata/data gap) memory: 1224K [ 0.901419] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 0.901420] x86/mm: Checking user space page tables [ 0.940887] x86/mm: Checked W+X mappings: passed, no W+X pages found. [ 0.940891] Run /init as init process [ 0.940893] with arguments: [ 0.940894] /init [ 0.940895] splash [ 0.940895] with environment: [ 0.940896] HOME=/ [ 0.940897] TERM=linux [ 0.940898] BOOT_IMAGE=/boot/vmlinuz-6.4.0 [ 1.108327] rtsx_pci 0000:01:00.0: enabling device (0000 -> 0002) [ 1.109979] i801_smbus 0000:00:1f.4: SMBus using PCI interrupt [ 1.112320] i2c i2c-0: 1/4 memory slots populated (from DMI) [ 1.113099] i2c i2c-0: Successfully instantiated SPD at 0x51 [ 1.116456] ahci 0000:00:17.0: version 3.0 [ 1.118112] e1000e: Intel(R) PRO/1000 Network Driver [ 1.118115] e1000e: Copyright(c) 1999 - 2015 Intel Corporation. [ 1.119630] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 1.120343] e1000e 0000:00:1f.6: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.120409] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1 [ 1.121579] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x110 quirks 0x0000000000009810 [ 1.127049] xhci_hcd 0000:00:14.0: xHCI Host Controller [ 1.127056] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2 [ 1.127061] xhci_hcd 0000:00:14.0: Host supports USB 3.1 Enhanced SuperSpeed [ 1.127115] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.04 [ 1.127119] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.127121] usb usb1: Product: xHCI Host Controller [ 1.127123] usb usb1: Manufacturer: Linux 6.4.0 xhci-hcd [ 1.127125] usb usb1: SerialNumber: 0000:00:14.0 [ 1.127358] hub 1-0:1.0: USB hub found [ 1.127391] hub 1-0:1.0: 16 ports detected [ 1.127768] ahci 0000:00:17.0: AHCI 0001.0301 32 slots 6 ports 6 Gbps 0x3f impl SATA mode [ 1.127774] ahci 0000:00:17.0: flags: 64bit ncq sntf clo only pio slum part ems deso sadm sds apst [ 1.131610] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.04 [ 1.131613] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.131615] usb usb2: Product: xHCI Host Controller [ 1.131616] usb usb2: Manufacturer: Linux 6.4.0 xhci-hcd [ 1.131618] usb usb2: SerialNumber: 0000:00:14.0 [ 1.131776] hub 2-0:1.0: USB hub found [ 1.131798] hub 2-0:1.0: 8 ports detected [ 1.189316] scsi host0: ahci [ 1.189520] scsi host1: ahci [ 1.189672] scsi host2: ahci [ 1.189911] scsi host3: ahci [ 1.190053] scsi host4: ahci [ 1.190311] scsi host5: ahci [ 1.190383] ata1: SATA max UDMA/133 abar m2048@0xa4539000 port 0xa4539100 irq 126 [ 1.190387] ata2: SATA max UDMA/133 abar m2048@0xa4539000 port 0xa4539180 irq 126 [ 1.190389] ata3: SATA max UDMA/133 abar m2048@0xa4539000 port 0xa4539200 irq 126 [ 1.190392] ata4: SATA max UDMA/133 abar m2048@0xa4539000 port 0xa4539280 irq 126 [ 1.190394] ata5: SATA max UDMA/133 abar m2048@0xa4539000 port 0xa4539300 irq 126 [ 1.190396] ata6: SATA max UDMA/133 abar m2048@0xa4539000 port 0xa4539380 irq 126 [ 1.376544] e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock [ 1.384567] usb 1-7: new low-speed USB device number 2 using xhci_hcd [ 1.408772] tsc: Refined TSC clocksource calibration: 3695.986 MHz [ 1.408790] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x6a8d0c5822e, max_idle_ns: 881591143436 ns [ 1.408856] clocksource: Switched to clocksource tsc [ 1.447378] e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) 70:85:c2:a4:19:95 [ 1.447392] e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection [ 1.447559] e1000e 0000:00:1f.6 eth0: MAC: 13, PHY: 12, PBA No: FFFFFF-0FF [ 1.503818] ata6: SATA link down (SStatus 4 SControl 300) [ 1.503871] ata1: SATA link down (SStatus 4 SControl 300) [ 1.503926] ata5: SATA link down (SStatus 4 SControl 300) [ 1.503978] ata2: SATA link down (SStatus 4 SControl 300) [ 1.507797] ata4: SATA link down (SStatus 4 SControl 300) [ 1.507854] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 1.510432] ata3.00: ACPI cmd f5/00:00:00:00:00:00(SECURITY FREEZE LOCK) filtered out [ 1.510448] ata3.00: ACPI cmd b1/c1:00:00:00:00:00(DEVICE CONFIGURATION OVERLAY) filtered out [ 1.511170] ata3.00: ATA-11: WDC WDS250G2B0A-00SM50, 401020WD, max UDMA/133 [ 1.511772] ata3.00: 488397168 sectors, multi 1: LBA48 NCQ (depth 32), AA [ 1.513389] ata3.00: Features: Dev-Sleep [ 1.516158] ata3.00: ACPI cmd f5/00:00:00:00:00:00(SECURITY FREEZE LOCK) filtered out [ 1.516174] ata3.00: ACPI cmd b1/c1:00:00:00:00:00(DEVICE CONFIGURATION OVERLAY) filtered out [ 1.519574] ata3.00: configured for UDMA/133 [ 1.519936] scsi 2:0:0:0: Direct-Access ATA WDC WDS250G2B0A 20WD PQ: 0 ANSI: 5 [ 1.521574] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 1.521657] sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/233 GiB) [ 1.521755] sd 2:0:0:0: [sda] Write Protect is off [ 1.521764] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.521843] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.521975] sd 2:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 1.525811] sda: sda1 sda2 [ 1.526296] sd 2:0:0:0: [sda] Attached SCSI disk [ 1.537077] usb 1-7: New USB device found, idVendor=17ef, idProduct=6044, bcdDevice= 0.08 [ 1.537099] usb 1-7: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 1.537113] usb 1-7: Product: ThinkPad USB Laser Mouse [ 1.545518] e1000e 0000:00:1f.6 eno1: renamed from eth0 [ 1.672576] usb 1-8: new low-speed USB device number 3 using xhci_hcd [ 1.826477] usb 1-8: New USB device found, idVendor=046d, idProduct=c31c, bcdDevice=64.00 [ 1.826492] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.826500] usb 1-8: Product: USB Keyboard [ 1.826506] usb 1-8: Manufacturer: Logitech [ 1.855188] hid: raw HID events driver (C) Jiri Kosina [ 1.877874] usbcore: registered new interface driver usbhid [ 1.877886] usbhid: USB HID core driver [ 1.886411] input: ThinkPad USB Laser Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.0/0003:17EF:6044.0001/input/input3 [ 1.886811] hid-generic 0003:17EF:6044.0001: input,hidraw0: USB HID v1.11 Mouse [ThinkPad USB Laser Mouse] on usb-0000:00:14.0-7/input0 [ 1.887468] input: Logitech USB Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.0/0003:046D:C31C.0002/input/input4 [ 1.944988] hid-generic 0003:046D:C31C.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech USB Keyboard] on usb-0000:00:14.0-8/input0 [ 1.945593] input: Logitech USB Keyboard Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.1/0003:046D:C31C.0003/input/input5 [ 2.004866] input: Logitech USB Keyboard System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-8/1-8:1.1/0003:046D:C31C.0003/input/input6 [ 2.005167] hid-generic 0003:046D:C31C.0003: input,hidraw2: USB HID v1.10 Device [Logitech USB Keyboard] on usb-0000:00:14.0-8/input1 [ 2.137604] EXT4-fs (sda2): mounted filesystem 74fe52d0-e90f-4b0a-92f4-581b5fa98519 ro with ordered data mode. Quota mode: none. [ 2.333222] systemd[1]: Inserted module 'autofs4' [ 2.398894] systemd[1]: systemd 245.4-4ubuntu3.22 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=hybrid) [ 2.399002] systemd[1]: Detected architecture x86-64. [ 2.461334] systemd[1]: Set hostname to <cr-desktop>. [ 2.497970] memfd_create() without MFD_EXEC nor MFD_NOEXEC_SEAL, pid=1 'systemd' [ 2.699291] systemd[1]: Created slice system-modprobe.slice. [ 2.699521] systemd[1]: Created slice system-postfix.slice. [ 2.699716] systemd[1]: Created slice system-systemd\x2dfsck.slice. [ 2.699914] systemd[1]: Created slice User and Session Slice. [ 2.699983] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 2.700140] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point. [ 2.700179] systemd[1]: Reached target User and Group Name Lookups. [ 2.700190] systemd[1]: Reached target Remote File Systems. [ 2.700199] systemd[1]: Reached target Slices. [ 2.700209] systemd[1]: Reached target Mounting snaps. [ 2.700317] systemd[1]: Listening on Syslog Socket. [ 2.700395] systemd[1]: Listening on fsck to fsckd communication Socket. [ 2.700446] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 2.700622] systemd[1]: Listening on Journal Audit Socket. [ 2.700699] systemd[1]: Listening on Journal Socket (/dev/log). [ 2.700792] systemd[1]: Listening on Journal Socket. [ 2.700887] systemd[1]: Listening on udev Control Socket. [ 2.700945] systemd[1]: Listening on udev Kernel Socket. [ 2.720720] systemd[1]: Mounting Huge Pages File System... [ 2.721716] systemd[1]: Mounting POSIX Message Queue File System... [ 2.723249] systemd[1]: Mounting Kernel Debug File System... [ 2.724663] systemd[1]: Mounting Kernel Trace File System... [ 2.726034] systemd[1]: Starting Journal Service... [ 2.727541] systemd[1]: Starting Set the console keyboard layout... [ 2.728927] systemd[1]: Starting Create list of static device nodes for the current kernel... [ 2.730266] systemd[1]: Starting Load Kernel Module chromeos_pstore... [ 2.731599] systemd[1]: Starting Load Kernel Module drm... [ 2.732964] systemd[1]: Starting Load Kernel Module efi_pstore... [ 2.734353] systemd[1]: Starting Load Kernel Module pstore_blk... [ 2.737969] systemd[1]: Starting Load Kernel Module pstore_zone... [ 2.739458] pstore: Using crash dump compression: deflate [ 2.755800] systemd[1]: Starting Load Kernel Module ramoops... [ 2.756665] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped. [ 2.756718] systemd[1]: Condition check resulted in File System Check on Root Device being skipped. [ 2.758718] systemd[1]: Starting Load Kernel Modules... [ 2.760081] systemd[1]: Starting Remount Root and Kernel File Systems... [ 2.761530] systemd[1]: Starting udev Coldplug all Devices... [ 2.764391] pstore: Registered efi_pstore as persistent store backend [ 2.765525] systemd[1]: Starting Uncomplicated firewall... [ 2.767875] systemd[1]: Mounted Huge Pages File System. [ 2.768043] systemd[1]: Mounted POSIX Message Queue File System. [ 2.768191] systemd[1]: Mounted Kernel Debug File System. [ 2.768323] systemd[1]: Mounted Kernel Trace File System. [ 2.769398] systemd[1]: Finished Create list of static device nodes for the current kernel. [ 2.769836] systemd[1]: modprobe@pstore_blk.service: Succeeded. [ 2.776581] systemd[1]: Finished Load Kernel Module pstore_blk. [ 2.776951] systemd[1]: modprobe@pstore_zone.service: Succeeded. [ 2.777567] systemd[1]: Finished Load Kernel Module pstore_zone. [ 2.778195] systemd[1]: Finished Uncomplicated firewall. [ 2.786382] EXT4-fs (sda2): re-mounted 74fe52d0-e90f-4b0a-92f4-581b5fa98519 r/w. Quota mode: none. [ 2.788765] systemd[1]: Finished Remount Root and Kernel File Systems. [ 2.789161] systemd[1]: modprobe@chromeos_pstore.service: Succeeded. [ 2.789705] systemd[1]: Finished Load Kernel Module chromeos_pstore. [ 2.791131] systemd[1]: Activating swap /swapfile... [ 2.798616] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 2.811189] systemd[1]: Starting Load/Save Random Seed... [ 2.817916] Adding 2097148k swap on /swapfile. Priority:-2 extents:6 across:2260988k SSFS [ 2.819454] systemd[1]: Starting Create System Users... [ 2.819567] systemd[1]: Activated swap /swapfile. [ 2.820097] systemd[1]: modprobe@efi_pstore.service: Succeeded. [ 2.820742] systemd[1]: Finished Load Kernel Module efi_pstore. [ 2.821081] ACPI: bus type drm_connector registered [ 2.821189] systemd[1]: modprobe@ramoops.service: Succeeded. [ 2.821712] systemd[1]: Finished Load Kernel Module ramoops. [ 2.822906] systemd[1]: Reached target Swap. [ 2.822985] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped. [ 2.823853] systemd[1]: modprobe@drm.service: Succeeded. [ 2.824373] systemd[1]: Finished Load Kernel Module drm. [ 2.834857] lp: driver loaded but no devices found [ 2.840286] ppdev: user-space parallel port driver [ 2.853157] systemd[1]: Finished Create System Users. [ 2.853849] systemd[1]: Finished Load/Save Random Seed. [ 2.855110] systemd[1]: Starting Create Static Device Nodes in /dev... [ 2.860726] systemd[1]: Started Journal Service. [ 2.874425] systemd-journald[222]: Received client request to flush runtime journal. [ 2.910112] loop0: detected capacity change from 0 to 8 [ 2.939647] loop1: detected capacity change from 0 to 114000 [ 2.940326] loop2: detected capacity change from 0 to 448512 [ 2.956870] loop3: detected capacity change from 0 to 447264 [ 2.956931] loop4: detected capacity change from 0 to 25240 [ 2.956987] loop5: detected capacity change from 0 to 994336 [ 2.957030] loop6: detected capacity change from 0 to 994336 [ 2.960594] loop7: detected capacity change from 0 to 129944 [ 2.960964] loop8: detected capacity change from 0 to 151296 [ 2.989276] loop9: detected capacity change from 0 to 109072 [ 2.989415] loop11: detected capacity change from 0 to 133320 [ 2.990015] loop10: detected capacity change from 0 to 113992 [ 3.001464] loop12: detected capacity change from 0 to 130848 [ 3.005343] loop14: detected capacity change from 0 to 104360 [ 3.016129] loop15: detected capacity change from 0 to 133424 [ 3.019776] loop13: detected capacity change from 0 to 187776 [ 3.311804] EDAC ie31200: No ECC support [ 3.390717] ee1004 0-0051: 512 byte EE1004-compliant SPD EEPROM, read-only [ 3.410393] mei_me 0000:00:16.0: enabling device (0000 -> 0002) [ 3.517293] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer [ 3.517297] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules [ 3.517299] RAPL PMU: hw unit of domain package 2^-14 Joules [ 3.517300] RAPL PMU: hw unit of domain dram 2^-14 Joules [ 3.517302] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules [ 3.527882] cryptd: max_cpu_qlen set to 1000 [ 3.550411] SSE version of gcm_enc/dec engaged. [ 3.822452] intel_rapl_common: Found RAPL domain package [ 3.822455] intel_rapl_common: Found RAPL domain core [ 3.822456] intel_rapl_common: Found RAPL domain uncore [ 3.822458] intel_rapl_common: Found RAPL domain dram [ 4.287882] Console: switching to colour dummy device 80x25 [ 4.287942] i915 0000:00:02.0: vgaarb: deactivate vga console [ 4.291998] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 4.293495] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) [ 4.295550] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4) [ 4.320960] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 [ 4.323784] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 4.324347] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7 [ 4.324481] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) [ 4.453028] fbcon: i915drmfb (fb0) is primary device [ 4.504699] Console: switching to colour frame buffer device 240x67 [ 4.522763] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device [ 4.591516] vfat filesystem being mounted at /boot/efi supports timestamps until 2107-12-31 (0x10391447e) [ 4.645541] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC892: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line [ 4.645555] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) [ 4.645563] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0) [ 4.645569] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 [ 4.645573] snd_hda_codec_realtek hdaudioC0D0: inputs: [ 4.645577] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19 [ 4.645583] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18 [ 4.645587] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a [ 4.696503] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input8 [ 4.696585] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input9 [ 4.696660] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1f.3/sound/card0/input10 [ 4.696743] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1f.3/sound/card0/input11 [ 4.696821] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input12 [ 4.696898] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input13 [ 4.696968] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input14 [ 4.697084] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input15 [ 4.932641] audit: type=1400 audit(4028029342.987:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-senddoc" pid=516 comm="apparmor_parser" [ 4.933595] audit: type=1400 audit(4028029342.987:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport" pid=515 comm="apparmor_parser" [ 4.938509] audit: type=1400 audit(4028029342.991:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=514 comm="apparmor_parser" [ 4.938519] audit: type=1400 audit(4028029342.991:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/NetworkManager/nm-dhcp-helper" pid=514 comm="apparmor_parser" [ 4.938523] audit: type=1400 audit(4028029342.991:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/connman/scripts/dhclient-script" pid=514 comm="apparmor_parser" [ 4.938527] audit: type=1400 audit(4028029342.991:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/{,usr/}sbin/dhclient" pid=514 comm="apparmor_parser" [ 4.938531] audit: type=1400 audit(4028029342.991:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed" pid=520 comm="apparmor_parser" [ 4.941453] audit: type=1400 audit(4028029342.995:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine" pid=519 comm="apparmor_parser" [ 4.941461] audit: type=1400 audit(4028029342.995:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=519 comm="apparmor_parser" [ 5.132577] kauditd_printk_skb: 19 callbacks suppressed [ 5.132580] audit: type=1400 audit(4028029343.187:30): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap-update-ns.sublime-text" pid=557 comm="apparmor_parser" [ 5.135090] audit: type=1400 audit(4028029343.187:31): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/snap/snapd/19457/usr/lib/snapd/snap-confine" pid=555 comm="apparmor_parser" [ 5.135098] audit: type=1400 audit(4028029343.187:32): apparmor="STATUS" operation="profile_load" profile="unconfined" name="/snap/snapd/19457/usr/lib/snapd/snap-confine//mount-namespace-capture-helper" pid=555 comm="apparmor_parser" [ 5.136211] audit: type=1400 audit(4028029343.187:33): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap.snap-store.hook.configure" pid=558 comm="apparmor_parser" [ 5.143517] audit: type=1400 audit(4028029343.195:34): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap.snap-store.snap-store" pid=559 comm="apparmor_parser" [ 5.147196] audit: type=1400 audit(4028029343.199:35): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap-update-ns.snap-store" pid=556 comm="apparmor_parser" [ 5.164996] audit: type=1400 audit(4028029343.219:36): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap.snap-store.ubuntu-software" pid=560 comm="apparmor_parser" [ 5.165157] audit: type=1400 audit(4028029343.219:37): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap.snap-store.ubuntu-software-local-file" pid=561 comm="apparmor_parser" [ 5.185193] audit: type=1400 audit(4028029343.239:38): apparmor="STATUS" operation="profile_load" profile="unconfined" name="snap.sublime-text.subl" pid=562 comm="apparmor_parser" [ 6.463469] loop16: detected capacity change from 0 to 8 [ 10.094244] rfkill: input handler disabled [ 43.180701] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ 43.180709] pcieport 0000:00:1c.0: pciehp: Slot(8): Card not present [ 44.403768] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present [ 44.403772] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up [ 44.540631] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 [ 44.540688] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 44.540744] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x000000ff 64bit] [ 44.541588] pci 0000:01:00.0: BAR 0: assigned [mem 0xa3b00000-0xa3b03fff 64bit] [ 44.541622] pci 0000:01:00.0: BAR 4: assigned [mem 0xa3b04000-0xa3b040ff 64bit] [ 44.541650] pcieport 0000:00:1c.0: PCI bridge to [bus 01] [ 44.541667] pcieport 0000:00:1c.0: bridge window [io 0x4000-0x4fff] [ 44.541681] pcieport 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] [ 44.541691] pcieport 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] [ 44.605052] nvme nvme0: pci function 0000:01:00.0 [ 44.605069] nvme 0000:01:00.0: enabling device (0000 -> 0002) [ 44.671175] nvme nvme0: 4/0/0 default/read/poll queues [ 44.675841] nvme0n1: p1 p2 [ 51.682628] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ 51.716800] nvme0n1: detected capacity change from 495050752 to 0 [ 51.793382] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present [ 51.793392] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up [ 51.928633] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 [ 51.928685] pci 0000:01:00.0: reg 0x10: [mem 0xa3b00000-0xa3b00fff] [ 51.928807] pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 128 (was 256, max 256) [ 51.928828] pci 0000:01:00.0: Max Payload Size set to 128 (was 128, max 128) [ 51.928996] pci 0000:01:00.0: supports D1 D2 [ 51.929002] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold [ 51.929637] pci 0000:01:00.0: BAR 0: assigned [mem 0xa3b00000-0xa3b00fff] [ 51.929657] pcieport 0000:00:1c.0: PCI bridge to [bus 01] [ 51.929673] pcieport 0000:00:1c.0: bridge window [io 0x4000-0x4fff] [ 51.929686] pcieport 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] [ 51.929697] pcieport 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] [ 54.872928] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ 56.146581] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present [ 56.146584] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up [ 56.284632] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 [ 56.284688] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 56.284745] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x000000ff 64bit] [ 56.285596] pci 0000:01:00.0: BAR 0: assigned [mem 0xa3b00000-0xa3b03fff 64bit] [ 56.285629] pci 0000:01:00.0: BAR 4: assigned [mem 0xa3b04000-0xa3b040ff 64bit] [ 56.285659] pcieport 0000:00:1c.0: PCI bridge to [bus 01] [ 56.285675] pcieport 0000:00:1c.0: bridge window [io 0x4000-0x4fff] [ 56.285688] pcieport 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] [ 56.285699] pcieport 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] [ 56.286092] nvme nvme0: pci function 0000:01:00.0 [ 56.286113] nvme 0000:01:00.0: enabling device (0000 -> 0002) [ 56.413757] nvme nvme0: 4/0/0 default/read/poll queues [ 56.419167] nvme0n1: p1 p2 [ 60.635845] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ 60.676842] nvme0n1: detected capacity change from 495050752 to 0 [ 60.748953] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present [ 60.748958] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up [ 60.884619] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 [ 60.884662] pci 0000:01:00.0: reg 0x10: [mem 0xa3b00000-0xa3b00fff] [ 60.884767] pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 128 (was 256, max 256) [ 60.884778] pci 0000:01:00.0: Max Payload Size set to 128 (was 128, max 128) [ 60.884917] pci 0000:01:00.0: supports D1 D2 [ 60.884921] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold [ 60.885537] pci 0000:01:00.0: BAR 0: assigned [mem 0xa3b00000-0xa3b00fff] [ 60.885570] pcieport 0000:00:1c.0: PCI bridge to [bus 01] [ 60.885585] pcieport 0000:00:1c.0: bridge window [io 0x4000-0x4fff] [ 60.885598] pcieport 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] [ 60.885630] pcieport 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ 63.912118] BUG: unable to handle page fault for address: ffffb24d403e5010 [ 63.912122] #PF: supervisor read access in kernel mode [ 63.912125] #PF: error_code(0x0000) - not-present page [ 63.912126] PGD 100000067 P4D 100000067 PUD 1001fe067 PMD 100d97067 PTE 0 [ 63.912131] Oops: 0000 [#1] PREEMPT SMP PTI [ 63.912134] CPU: 3 PID: 534 Comm: kworker/3:10 Not tainted 6.4.0 #6 [ 63.912137] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./H370M Pro4, BIOS P3.40 10/25/2018 [ 63.912138] Workqueue: pm pm_runtime_work [ 63.912144] RIP: 0010:ioread32+0x2e/0x70 [ 63.912148] Code: ff 03 00 77 25 48 81 ff 00 00 01 00 77 14 8b 15 08 d9 54 01 b8 ff ff ff ff 85 d2 75 14 c3 cc cc cc cc 89 fa ed c3 cc cc cc cc <8b> 07 c3 cc cc cc cc 55 83 ea 01 48 89 fe 48 c7 c7 98 6f 15 99 48 [ 63.912150] RSP: 0018:ffffb24d40a5bd78 EFLAGS: 00010296 [ 63.912152] RAX: ffffb24d403e5000 RBX: 0000000000000152 RCX: 000000000000007f [ 63.912153] RDX: 000000000000ff00 RSI: ffffb24d403e5010 RDI: ffffb24d403e5010 [ 63.912155] RBP: ffffb24d40a5bd98 R08: ffffb24d403e5010 R09: 0000000000000000 [ 63.912156] R10: ffff9074cd95e7f4 R11: 0000000000000003 R12: 000000000000007f [ 63.912158] R13: ffff9074e1a68c00 R14: ffff9074e1a68d00 R15: 0000000000009003 [ 63.912159] FS: 0000000000000000(0000) GS:ffff90752a180000(0000) knlGS:0000000000000000 [ 63.912161] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 63.912162] CR2: ffffb24d403e5010 CR3: 0000000152832006 CR4: 00000000003706e0 [ 63.912164] Call Trace: [ 63.912165] <TASK> [ 63.912167] ? show_regs+0x68/0x70 [ 63.912171] ? __die_body+0x20/0x70 [ 63.912173] ? __die+0x2b/0x40 [ 63.912175] ? page_fault_oops+0x160/0x480 [ 63.912177] ? search_bpf_extables+0x63/0x90 [ 63.912180] ? ioread32+0x2e/0x70 [ 63.912183] ? search_exception_tables+0x5f/0x70 [ 63.912186] ? kernelmode_fixup_or_oops+0xa2/0x120 [ 63.912189] ? __bad_area_nosemaphore+0x179/0x230 [ 63.912191] ? bad_area_nosemaphore+0x16/0x20 [ 63.912193] ? do_kern_addr_fault+0x8b/0xa0 [ 63.912195] ? exc_page_fault+0xe5/0x180 [ 63.912198] ? asm_exc_page_fault+0x27/0x30 [ 63.912203] ? ioread32+0x2e/0x70 [ 63.912206] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] [ 63.912217] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] [ 63.912226] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] [ 63.912234] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] [ 63.912243] ? __pfx_pci_pm_runtime_idle+0x10/0x10 [ 63.912246] pci_pm_runtime_idle+0x34/0x70 [ 63.912248] rpm_idle+0xc4/0x2b0 [ 63.912251] pm_runtime_work+0x93/0xc0 [ 63.912254] process_one_work+0x21a/0x430 [ 63.912258] worker_thread+0x4a/0x3c0 [ 63.912261] ? __pfx_worker_thread+0x10/0x10 [ 63.912263] kthread+0x106/0x140 [ 63.912266] ? __pfx_kthread+0x10/0x10 [ 63.912268] ret_from_fork+0x29/0x50 [ 63.912273] </TASK> [ 63.912274] Modules linked in: nvme nvme_core snd_hda_codec_hdmi snd_sof_pci_intel_cnl snd_sof_intel_hda_common snd_hda_codec_realtek snd_hda_codec_generic snd_soc_hdac_hda soundwire_intel ledtrig_audio nls_iso8859_1 soundwire_generic_allocation soundwire_cadence snd_sof_intel_hda_mlink snd_sof_intel_hda snd_sof_pci snd_sof_xtensa_dsp snd_sof snd_sof_utils snd_hda_ext_core snd_soc_acpi_intel_match snd_soc_acpi soundwire_bus snd_soc_core snd_compress ac97_bus snd_pcm_dmaengine snd_hda_intel i915 snd_intel_dspcfg snd_intel_sdw_acpi intel_rapl_msr snd_hda_codec intel_rapl_common snd_hda_core x86_pkg_temp_thermal intel_powerclamp snd_hwdep coretemp snd_pcm kvm_intel drm_buddy ttm mei_hdcp kvm drm_display_helper snd_seq_midi snd_seq_midi_event cec crct10dif_pclmul ghash_clmulni_intel sha512_ssse3 aesni_intel crypto_simd rc_core cryptd rapl snd_rawmidi drm_kms_helper binfmt_misc intel_cstate i2c_algo_bit joydev snd_seq snd_seq_device syscopyarea wmi_bmof snd_timer sysfillrect input_leds snd ee1004 sysimgblt mei_me soundcore [ 63.912324] mei intel_pch_thermal mac_hid acpi_tad acpi_pad sch_fq_codel msr parport_pc ppdev lp ramoops drm parport reed_solomon efi_pstore ip_tables x_tables autofs4 hid_generic usbhid hid rtsx_pci_sdmmc crc32_pclmul ahci e1000e i2c_i801 i2c_smbus rtsx_pci xhci_pci libahci xhci_pci_renesas video wmi [ 63.912346] CR2: ffffb24d403e5010 [ 63.912348] ---[ end trace 0000000000000000 ]--- [ 64.067753] RIP: 0010:ioread32+0x2e/0x70 [ 64.067762] Code: ff 03 00 77 25 48 81 ff 00 00 01 00 77 14 8b 15 08 d9 54 01 b8 ff ff ff ff 85 d2 75 14 c3 cc cc cc cc 89 fa ed c3 cc cc cc cc <8b> 07 c3 cc cc cc cc 55 83 ea 01 48 89 fe 48 c7 c7 98 6f 15 99 48 [ 64.067764] RSP: 0018:ffffb24d40a5bd78 EFLAGS: 00010296 [ 64.067767] RAX: ffffb24d403e5000 RBX: 0000000000000152 RCX: 000000000000007f [ 64.067769] RDX: 000000000000ff00 RSI: ffffb24d403e5010 RDI: ffffb24d403e5010 [ 64.067770] RBP: ffffb24d40a5bd98 R08: ffffb24d403e5010 R09: 0000000000000000 [ 64.067772] R10: ffff9074cd95e7f4 R11: 0000000000000003 R12: 000000000000007f [ 64.067773] R13: ffff9074e1a68c00 R14: ffff9074e1a68d00 R15: 0000000000009003 [ 64.067775] FS: 0000000000000000(0000) GS:ffff90752a180000(0000) knlGS:0000000000000000 [ 64.067776] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 64.067778] CR2: ffffb24d403e5010 CR3: 0000000119402003 CR4: 00000000003706e0 [ 64.067780] note: kworker/3:10[534] exited with irqs disabled
On Thu, Oct 19, 2023 at 01:49:50AM +0000, Ricky WU wrote: > [ 0.267813] pci 0000:00:1c.0: [8086:a33c] type 01 class 0x060400 Cannon Lake PCH Root Port > [ 0.275241] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 > [ 0.275315] pci 0000:01:00.0: reg 0x10: [mem 0xa3b00000-0xa3b00fff] > [ 0.275782] pci 0000:01:00.0: supports D1 D2 > [ 0.275784] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold > [ 0.276490] pci 0000:00:1c.0: PCI bridge to [bus 01] Device below Root Port is initially a Realtek RTS5261 card reader. > [ 0.395968] pcieport 0000:00:1c.0: PME: Signaling with IRQ 122 > [ 0.396009] pcieport 0000:00:1c.0: pciehp: Slot #8 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+ Root Port is hotplug-capable. > [ 43.180701] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 43.180709] pcieport 0000:00:1c.0: pciehp: Slot(8): Card not present > [ 44.403768] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > [ 44.403772] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > [ 44.540631] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 Card reader is unplugged and replaced by SanDisk SN530 NVMe SSD. > [ 51.682628] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 51.716800] nvme0n1: detected capacity change from 495050752 to 0 > [ 51.793382] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > [ 51.793392] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > [ 51.928633] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 NVMe SSD replaced by the card reader again. > [ 54.872928] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 56.146581] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > [ 56.146584] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > [ 56.284632] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 Card reader replaced by NVMe SSD, second time. > [ 60.635845] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 60.676842] nvme0n1: detected capacity change from 495050752 to 0 > [ 60.748953] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > [ 60.748958] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > [ 60.884619] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 NVMe SSD replaced by the card reader, second time. > [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 63.912118] BUG: unable to handle page fault for address: ffffb24d403e5010 Card reader replaced with NVMe SSD, third time. So it took three tries to reproduce the page fault. Thanks for the log, the issue is a little less murky now. But it's still unclear what the root cause is and thus what the proper solution is. I think this needs more in-depth debugging, see my previous e-mail. Hope that helps! Thanks, Lukas
Hi Lukas and Ricky, On Thu, Oct 19, 2023 at 5:35 PM Lukas Wunner <lukas@wunner.de> wrote: > > On Thu, Oct 19, 2023 at 01:49:50AM +0000, Ricky WU wrote: > > [ 0.267813] pci 0000:00:1c.0: [8086:a33c] type 01 class 0x060400 > > Cannon Lake PCH Root Port > > > [ 0.275241] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 > > [ 0.275315] pci 0000:01:00.0: reg 0x10: [mem 0xa3b00000-0xa3b00fff] > > [ 0.275782] pci 0000:01:00.0: supports D1 D2 > > [ 0.275784] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold > > [ 0.276490] pci 0000:00:1c.0: PCI bridge to [bus 01] > > Device below Root Port is initially a Realtek RTS5261 card reader. > > > [ 0.395968] pcieport 0000:00:1c.0: PME: Signaling with IRQ 122 > > [ 0.396009] pcieport 0000:00:1c.0: pciehp: Slot #8 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl+ IbPresDis- LLActRep+ > > Root Port is hotplug-capable. > > > [ 43.180701] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > [ 43.180709] pcieport 0000:00:1c.0: pciehp: Slot(8): Card not present > > [ 44.403768] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > > [ 44.403772] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > > [ 44.540631] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 > > Card reader is unplugged and replaced by SanDisk SN530 NVMe SSD. > > > [ 51.682628] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > [ 51.716800] nvme0n1: detected capacity change from 495050752 to 0 > > [ 51.793382] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > > [ 51.793392] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > > [ 51.928633] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 > > NVMe SSD replaced by the card reader again. > > > [ 54.872928] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > [ 56.146581] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > > [ 56.146584] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > > [ 56.284632] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 > > Card reader replaced by NVMe SSD, second time. > > > [ 60.635845] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > [ 60.676842] nvme0n1: detected capacity change from 495050752 to 0 > > [ 60.748953] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > > [ 60.748958] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > > [ 60.884619] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 > > NVMe SSD replaced by the card reader, second time. > > > [ 63.898861] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > > [ 63.912118] BUG: unable to handle page fault for address: ffffb24d403e5010 > > Card reader replaced with NVMe SSD, third time. > > So it took three tries to reproduce the page fault. > > Thanks for the log, the issue is a little less murky now. > But it's still unclear what the root cause is and thus > what the proper solution is. I think this needs more > in-depth debugging, see my previous e-mail. > > Hope that helps! Thanks, I think the following approach should cover all the cases? Ricky, can you please give it a try? diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c index d749ea8250d6..907d60587227 100644 --- a/drivers/pci/remove.c +++ b/drivers/pci/remove.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0 #include <linux/pci.h> #include <linux/module.h> +#include <linux/pm_runtime.h> #include "pci.h" static void pci_free_resources(struct pci_dev *dev) @@ -89,6 +90,8 @@ static void pci_remove_bus_device(struct pci_dev *dev) struct pci_bus *bus = dev->subordinate; struct pci_dev *child, *tmp; + pm_runtime_barrier(&dev->dev); + if (bus) { list_for_each_entry_safe(child, tmp, &bus->devices, bus_list) > > Lukas
> Hi Lukas and Ricky, > > I think the following approach should cover all the cases? > Ricky, can you please give it a try? > This patch is invalid for this issue, Problem reappears after plugging and unplugging twice Dmesg as below, [...] [ 360.771161] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ 360.771165] pcieport 0000:00:1c.0: pciehp: Slot(8): Card not present [ 361.986932] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present [ 361.986937] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up [ 362.120635] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 [ 362.120691] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] [ 362.120747] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x000000ff 64bit] [ 362.121606] pci 0000:01:00.0: BAR 0: assigned [mem 0xa3b00000-0xa3b03fff 64bit] [ 362.121646] pci 0000:01:00.0: BAR 4: assigned [mem 0xa3b04000-0xa3b040ff 64bit] [ 362.121686] pcieport 0000:00:1c.0: PCI bridge to [bus 01] [ 362.121702] pcieport 0000:00:1c.0: bridge window [io 0x4000-0x4fff] [ 362.121743] pcieport 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] [ 362.121761] pcieport 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] [ 362.171709] nvme nvme0: pci function 0000:01:00.0 [ 362.171726] nvme 0000:01:00.0: enabling device (0000 -> 0002) [ 362.256724] nvme nvme0: 4/0/0 default/read/poll queues [ 362.261656] nvme0n1: p1 p2 [ 369.343246] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ 369.457450] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present [ 369.457462] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up [ 369.592600] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 [ 369.592654] pci 0000:01:00.0: reg 0x10: [mem 0xa3b00000-0xa3b00fff] [ 369.592776] pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 128 (was 256, max 256) [ 369.592797] pci 0000:01:00.0: Max Payload Size set to 128 (was 128, max 128) [ 369.592964] pci 0000:01:00.0: supports D1 D2 [ 369.592970] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold [ 369.593642] pci 0000:01:00.0: BAR 0: assigned [mem 0xa3b00000-0xa3b00fff] [ 369.593662] pcieport 0000:00:1c.0: PCI bridge to [bus 01] [ 369.593679] pcieport 0000:00:1c.0: bridge window [io 0x4000-0x4fff] [ 369.593692] pcieport 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] [ 369.593703] pcieport 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] [ 372.573757] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ 372.586620] BUG: unable to handle page fault for address: ffffc90000089010 [ 372.586624] #PF: supervisor read access in kernel mode [ 372.586626] #PF: error_code(0x0000) - not-present page [ 372.586627] PGD 100000067 P4D 100000067 PUD 10020a067 PMD 10020b067 PTE 0 [ 372.586632] Oops: 0000 [#1] PREEMPT SMP PTI [ 372.586634] CPU: 2 PID: 157 Comm: kworker/2:2 Not tainted 6.6.0-rc4 #12 [ 372.586637] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./H370M Pro4, BIOS P3.40 10/25/2018 [ 372.586639] Workqueue: pm pm_runtime_work [ 372.586644] RIP: 0010:ioread32+0x2e/0x70 [ 372.586647] Code: ff 03 00 77 25 48 81 ff 00 00 01 00 77 14 8b 15 98 ac 52 01 b8 ff ff ff ff 85 d2 75 14 c3 cc cc cc cc 89 fa ed c3 cc cc cc cc <8b> 07 c3 cc cc cc cc 55 83 ea 01 48 89 fe 48 c7 c7 f8 97 57 86 48 [ 372.586649] RSP: 0018:ffffc90000543d50 EFLAGS: 00010296 [ 372.586652] RAX: ffffc90000089000 RBX: 000000000000032f RCX: 000000000000007f [ 372.586653] RDX: 000000000000ff00 RSI: ffffc90000089010 RDI: ffffc90000089010 [ 372.586655] RBP: ffffc90000543d70 R08: ffffc90000089010 R09: ffff88816a132368 [ 372.586656] R10: 0000000000000000 R11: 0000000000000003 R12: 000000000000007f [ 372.586657] R13: ffff8881060ed000 R14: ffff8881060ed100 R15: 0000000000009003 [ 372.586659] FS: 0000000000000000(0000) GS:ffff88816a100000(0000) knlGS:0000000000000000 [ 372.586661] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 372.586662] CR2: ffffc90000089010 CR3: 0000000043032006 CR4: 00000000003706e0 [ 372.586664] Call Trace: [ 372.586665] <TASK> [ 372.586667] ? show_regs+0x68/0x70 [ 372.586671] ? __die_body+0x20/0x70 [ 372.586674] ? __die+0x2b/0x40 [ 372.586677] ? page_fault_oops+0x160/0x480 [ 372.586680] ? search_bpf_extables+0x63/0x90 [ 372.586684] ? ioread32+0x2e/0x70 [ 372.586686] ? search_exception_tables+0x5f/0x70 [ 372.586689] ? kernelmode_fixup_or_oops+0xa2/0x120 [ 372.586692] ? __bad_area_nosemaphore+0x179/0x230 [ 372.586696] ? bad_area_nosemaphore+0x16/0x20 [ 372.586698] ? do_kern_addr_fault+0x8b/0xa0 [ 372.586701] ? exc_page_fault+0xe5/0x180 [ 372.586705] ? asm_exc_page_fault+0x27/0x30 [ 372.586710] ? ioread32+0x2e/0x70 [ 372.586714] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] [ 372.586723] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] [ 372.586731] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] [ 372.586740] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] [ 372.586748] ? __pfx_pci_pm_runtime_idle+0x10/0x10 [ 372.586751] pci_pm_runtime_idle+0x34/0x70 [ 372.586753] rpm_idle+0xc4/0x2b0 [ 372.586756] pm_runtime_work+0x93/0xc0 [ 372.586759] process_scheduled_works+0x9a/0x390 [ 372.586762] ? __pfx_worker_thread+0x10/0x10 [ 372.586764] worker_thread+0x15b/0x2d0 [ 372.586767] ? __pfx_worker_thread+0x10/0x10 [ 372.586769] kthread+0x106/0x140 [ 372.586771] ? __pfx_kthread+0x10/0x10 [ 372.586774] ret_from_fork+0x39/0x60 [ 372.586776] ? __pfx_kthread+0x10/0x10 [ 372.586778] ret_from_fork_asm+0x1b/0x30 [ 372.586783] </TASK> [ 372.586784] Modules linked in: nvme nvme_core snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio nls_iso8859_1 snd_sof_pci_intel_cnl snd_sof_intel_hda_common snd_soc_hdac_hda soundwire_intel soundwire_generic_allocation snd_sof_intel_hda_mlink soundwire_cadence snd_sof_intel_hda snd_sof_pci snd_sof_xtensa_dsp snd_sof snd_sof_utils snd_hda_ext_core snd_soc_acpi_intel_match snd_soc_acpi soundwire_bus intel_rapl_msr intel_rapl_common snd_soc_core x86_pkg_temp_thermal intel_powerclamp coretemp snd_compress ac97_bus kvm_intel snd_pcm_dmaengine i915 snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi kvm snd_hda_codec snd_hda_core mei_hdcp crct10dif_pclmul ghash_clmulni_intel snd_hwdep snd_pcm sha512_ssse3 aesni_intel snd_seq_midi crypto_simd snd_seq_midi_event cryptd rapl snd_rawmidi intel_cstate drm_buddy binfmt_misc ttm snd_seq drm_display_helper joydev input_leds cec snd_seq_device wmi_bmof snd_timer ee1004 mei_me rc_core snd drm_kms_helper mei intel_pch_thermal i2c_algo_bit soundcore mac_hid [ 372.586834] acpi_tad acpi_pad sch_fq_codel msr parport_pc ppdev lp parport drm ramoops reed_solomon efi_pstore ip_tables x_tables autofs4 hid_generic usbhid hid rtsx_pci_sdmmc ahci i2c_i801 e1000e crc32_pclmul rtsx_pci i2c_smbus xhci_pci libahci xhci_pci_renesas video wmi [ 372.586856] CR2: ffffc90000089010 [ 372.586858] ---[ end trace 0000000000000000 ]--- [ 372.746808] RIP: 0010:ioread32+0x2e/0x70 [ 372.746816] Code: ff 03 00 77 25 48 81 ff 00 00 01 00 77 14 8b 15 98 ac 52 01 b8 ff ff ff ff 85 d2 75 14 c3 cc cc cc cc 89 fa ed c3 cc cc cc cc <8b> 07 c3 cc cc cc cc 55 83 ea 01 48 89 fe 48 c7 c7 f8 97 57 86 48 [ 372.746818] RSP: 0018:ffffc90000543d50 EFLAGS: 00010296 [ 372.746821] RAX: ffffc90000089000 RBX: 000000000000032f RCX: 000000000000007f [ 372.746823] RDX: 000000000000ff00 RSI: ffffc90000089010 RDI: ffffc90000089010 [ 372.746825] RBP: ffffc90000543d70 R08: ffffc90000089010 R09: ffff88816a132368 [ 372.746826] R10: 0000000000000000 R11: 0000000000000003 R12: 000000000000007f [ 372.746828] R13: ffff8881060ed000 R14: ffff8881060ed100 R15: 0000000000009003 [ 372.746830] FS: 0000000000000000(0000) GS:ffff88816a100000(0000) knlGS:0000000000000000 [ 372.746832] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 372.746833] CR2: ffffc90000089010 CR3: 000000010a564004 CR4: 00000000003706e0 [ 372.746835] note: kworker/2:2[157] exited with irqs disabled > diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c index > d749ea8250d6..907d60587227 100644 > --- a/drivers/pci/remove.c > +++ b/drivers/pci/remove.c > @@ -1,6 +1,7 @@ > // SPDX-License-Identifier: GPL-2.0 > #include <linux/pci.h> > #include <linux/module.h> > +#include <linux/pm_runtime.h> > #include "pci.h" > > static void pci_free_resources(struct pci_dev *dev) @@ -89,6 +90,8 @@ > static void pci_remove_bus_device(struct pci_dev *dev) > struct pci_bus *bus = dev->subordinate; > struct pci_dev *child, *tmp; > > + pm_runtime_barrier(&dev->dev); > + > if (bus) { > list_for_each_entry_safe(child, tmp, > &bus->devices, bus_list) > >
Hi Ricky, On Fri, Nov 10, 2023 at 10:41 AM Ricky WU <ricky_wu@realtek.com> wrote: > > > Hi Lukas and Ricky, > > > > I think the following approach should cover all the cases? > > Ricky, can you please give it a try? > > > > This patch is invalid for this issue, > Problem reappears after plugging and unplugging twice > Dmesg as below, My bad. The pm_runtime_barrier() should be called earlier. Can you please give the following a try: diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c index d749ea8250d6..c69b4ce5dbfd 100644 --- a/drivers/pci/remove.c +++ b/drivers/pci/remove.c @@ -1,6 +1,7 @@ // SPDX-License-Identifier: GPL-2.0 #include <linux/pci.h> #include <linux/module.h> +#include <linux/pm_runtime.h> #include "pci.h" static void pci_free_resources(struct pci_dev *dev) @@ -18,6 +19,7 @@ static void pci_stop_dev(struct pci_dev *dev) pci_pme_active(dev, false); if (pci_dev_is_added(dev)) { + pm_runtime_barrier(&dev->dev); device_release_driver(&dev->dev); pci_proc_detach_device(dev); > [...] > [ 360.771161] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 360.771165] pcieport 0000:00:1c.0: pciehp: Slot(8): Card not present > [ 361.986932] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > [ 361.986937] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > [ 362.120635] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 > [ 362.120691] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit] > [ 362.120747] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x000000ff 64bit] > [ 362.121606] pci 0000:01:00.0: BAR 0: assigned [mem 0xa3b00000-0xa3b03fff 64bit] > [ 362.121646] pci 0000:01:00.0: BAR 4: assigned [mem 0xa3b04000-0xa3b040ff 64bit] > [ 362.121686] pcieport 0000:00:1c.0: PCI bridge to [bus 01] > [ 362.121702] pcieport 0000:00:1c.0: bridge window [io 0x4000-0x4fff] > [ 362.121743] pcieport 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] > [ 362.121761] pcieport 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] > [ 362.171709] nvme nvme0: pci function 0000:01:00.0 > [ 362.171726] nvme 0000:01:00.0: enabling device (0000 -> 0002) > [ 362.256724] nvme nvme0: 4/0/0 default/read/poll queues > [ 362.261656] nvme0n1: p1 p2 > [ 369.343246] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 369.457450] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present > [ 369.457462] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up > [ 369.592600] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 > [ 369.592654] pci 0000:01:00.0: reg 0x10: [mem 0xa3b00000-0xa3b00fff] > [ 369.592776] pci 0000:01:00.0: Upstream bridge's Max Payload Size set to 128 (was 256, max 256) > [ 369.592797] pci 0000:01:00.0: Max Payload Size set to 128 (was 128, max 128) > [ 369.592964] pci 0000:01:00.0: supports D1 D2 > [ 369.592970] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold > [ 369.593642] pci 0000:01:00.0: BAR 0: assigned [mem 0xa3b00000-0xa3b00fff] > [ 369.593662] pcieport 0000:00:1c.0: PCI bridge to [bus 01] > [ 369.593679] pcieport 0000:00:1c.0: bridge window [io 0x4000-0x4fff] > [ 369.593692] pcieport 0000:00:1c.0: bridge window [mem 0xa3b00000-0xa44fffff] > [ 369.593703] pcieport 0000:00:1c.0: bridge window [mem 0xa0a00000-0xa13fffff 64bit pref] > [ 372.573757] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down > [ 372.586620] BUG: unable to handle page fault for address: ffffc90000089010 > [ 372.586624] #PF: supervisor read access in kernel mode > [ 372.586626] #PF: error_code(0x0000) - not-present page > [ 372.586627] PGD 100000067 P4D 100000067 PUD 10020a067 PMD 10020b067 PTE 0 > [ 372.586632] Oops: 0000 [#1] PREEMPT SMP PTI > [ 372.586634] CPU: 2 PID: 157 Comm: kworker/2:2 Not tainted 6.6.0-rc4 #12 > [ 372.586637] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./H370M Pro4, BIOS P3.40 10/25/2018 > [ 372.586639] Workqueue: pm pm_runtime_work > [ 372.586644] RIP: 0010:ioread32+0x2e/0x70 > [ 372.586647] Code: ff 03 00 77 25 48 81 ff 00 00 01 00 77 14 8b 15 98 ac 52 01 b8 ff ff ff ff 85 d2 75 14 c3 cc cc cc cc 89 fa ed c3 cc cc cc cc <8b> 07 c3 cc cc cc cc 55 83 ea 01 48 89 fe 48 c7 c7 f8 97 57 86 48 > [ 372.586649] RSP: 0018:ffffc90000543d50 EFLAGS: 00010296 > [ 372.586652] RAX: ffffc90000089000 RBX: 000000000000032f RCX: 000000000000007f > [ 372.586653] RDX: 000000000000ff00 RSI: ffffc90000089010 RDI: ffffc90000089010 > [ 372.586655] RBP: ffffc90000543d70 R08: ffffc90000089010 R09: ffff88816a132368 > [ 372.586656] R10: 0000000000000000 R11: 0000000000000003 R12: 000000000000007f > [ 372.586657] R13: ffff8881060ed000 R14: ffff8881060ed100 R15: 0000000000009003 > [ 372.586659] FS: 0000000000000000(0000) GS:ffff88816a100000(0000) knlGS:0000000000000000 > [ 372.586661] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > [ 372.586662] CR2: ffffc90000089010 CR3: 0000000043032006 CR4: 00000000003706e0 > [ 372.586664] Call Trace: > [ 372.586665] <TASK> > [ 372.586667] ? show_regs+0x68/0x70 > [ 372.586671] ? __die_body+0x20/0x70 > [ 372.586674] ? __die+0x2b/0x40 > [ 372.586677] ? page_fault_oops+0x160/0x480 > [ 372.586680] ? search_bpf_extables+0x63/0x90 > [ 372.586684] ? ioread32+0x2e/0x70 > [ 372.586686] ? search_exception_tables+0x5f/0x70 > [ 372.586689] ? kernelmode_fixup_or_oops+0xa2/0x120 > [ 372.586692] ? __bad_area_nosemaphore+0x179/0x230 > [ 372.586696] ? bad_area_nosemaphore+0x16/0x20 > [ 372.586698] ? do_kern_addr_fault+0x8b/0xa0 > [ 372.586701] ? exc_page_fault+0xe5/0x180 > [ 372.586705] ? asm_exc_page_fault+0x27/0x30 > [ 372.586710] ? ioread32+0x2e/0x70 > [ 372.586714] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] > [ 372.586723] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] > [ 372.586731] rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] > [ 372.586740] rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] > [ 372.586748] ? __pfx_pci_pm_runtime_idle+0x10/0x10 > [ 372.586751] pci_pm_runtime_idle+0x34/0x70 > [ 372.586753] rpm_idle+0xc4/0x2b0 > [ 372.586756] pm_runtime_work+0x93/0xc0 > [ 372.586759] process_scheduled_works+0x9a/0x390 > [ 372.586762] ? __pfx_worker_thread+0x10/0x10 > [ 372.586764] worker_thread+0x15b/0x2d0 > [ 372.586767] ? __pfx_worker_thread+0x10/0x10 > [ 372.586769] kthread+0x106/0x140 > [ 372.586771] ? __pfx_kthread+0x10/0x10 > [ 372.586774] ret_from_fork+0x39/0x60 > [ 372.586776] ? __pfx_kthread+0x10/0x10 > [ 372.586778] ret_from_fork_asm+0x1b/0x30 > [ 372.586783] </TASK> > [ 372.586784] Modules linked in: nvme nvme_core snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio nls_iso8859_1 snd_sof_pci_intel_cnl snd_sof_intel_hda_common snd_soc_hdac_hda soundwire_intel soundwire_generic_allocation snd_sof_intel_hda_mlink soundwire_cadence snd_sof_intel_hda snd_sof_pci snd_sof_xtensa_dsp snd_sof snd_sof_utils snd_hda_ext_core snd_soc_acpi_intel_match snd_soc_acpi soundwire_bus intel_rapl_msr intel_rapl_common snd_soc_core x86_pkg_temp_thermal intel_powerclamp coretemp snd_compress ac97_bus kvm_intel snd_pcm_dmaengine i915 snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi kvm snd_hda_codec snd_hda_core mei_hdcp crct10dif_pclmul ghash_clmulni_intel snd_hwdep snd_pcm sha512_ssse3 aesni_intel snd_seq_midi crypto_simd snd_seq_midi_event cryptd rapl snd_rawmidi intel_cstate drm_buddy binfmt_misc ttm snd_seq drm_display_helper joydev input_leds cec snd_seq_device wmi_bmof snd_timer ee1004 mei_me rc_core snd drm_kms_helper mei intel_pch_thermal i2c_algo_bit soundcore mac_hid > [ 372.586834] acpi_tad acpi_pad sch_fq_codel msr parport_pc ppdev lp parport drm ramoops reed_solomon efi_pstore ip_tables x_tables autofs4 hid_generic usbhid hid rtsx_pci_sdmmc ahci i2c_i801 e1000e crc32_pclmul rtsx_pci i2c_smbus xhci_pci libahci xhci_pci_renesas video wmi > [ 372.586856] CR2: ffffc90000089010 > [ 372.586858] ---[ end trace 0000000000000000 ]--- > [ 372.746808] RIP: 0010:ioread32+0x2e/0x70 > [ 372.746816] Code: ff 03 00 77 25 48 81 ff 00 00 01 00 77 14 8b 15 98 ac 52 01 b8 ff ff ff ff 85 d2 75 14 c3 cc cc cc cc 89 fa ed c3 cc cc cc cc <8b> 07 c3 cc cc cc cc 55 83 ea 01 48 89 fe 48 c7 c7 f8 97 57 86 48 > [ 372.746818] RSP: 0018:ffffc90000543d50 EFLAGS: 00010296 > [ 372.746821] RAX: ffffc90000089000 RBX: 000000000000032f RCX: 000000000000007f > [ 372.746823] RDX: 000000000000ff00 RSI: ffffc90000089010 RDI: ffffc90000089010 > [ 372.746825] RBP: ffffc90000543d70 R08: ffffc90000089010 R09: ffff88816a132368 > [ 372.746826] R10: 0000000000000000 R11: 0000000000000003 R12: 000000000000007f > [ 372.746828] R13: ffff8881060ed000 R14: ffff8881060ed100 R15: 0000000000009003 > [ 372.746830] FS: 0000000000000000(0000) GS:ffff88816a100000(0000) knlGS:0000000000000000 > [ 372.746832] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 > [ 372.746833] CR2: ffffc90000089010 CR3: 000000010a564004 CR4: 00000000003706e0 > [ 372.746835] note: kworker/2:2[157] exited with irqs disabled > > > diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c index > > d749ea8250d6..907d60587227 100644 > > --- a/drivers/pci/remove.c > > +++ b/drivers/pci/remove.c > > @@ -1,6 +1,7 @@ > > // SPDX-License-Identifier: GPL-2.0 > > #include <linux/pci.h> > > #include <linux/module.h> > > +#include <linux/pm_runtime.h> > > #include "pci.h" > > > > static void pci_free_resources(struct pci_dev *dev) @@ -89,6 +90,8 @@ > > static void pci_remove_bus_device(struct pci_dev *dev) > > struct pci_bus *bus = dev->subordinate; > > struct pci_dev *child, *tmp; > > > > + pm_runtime_barrier(&dev->dev); > > + > > if (bus) { > > list_for_each_entry_safe(child, tmp, > > &bus->devices, bus_list) > > > > >
> Hi Ricky, > > On Fri, Nov 10, 2023 at 10:41 AM Ricky WU <ricky_wu@realtek.com> wrote: > > > > > Hi Lukas and Ricky, > > > > > > I think the following approach should cover all the cases? > > > Ricky, can you please give it a try? > > > > > > > This patch is invalid for this issue, > > Problem reappears after plugging and unplugging twice Dmesg as below, > > My bad. The pm_runtime_barrier() should be called earlier. > Can you please give the following a try: > Hi Kai-heng， Sorry for late, This patch is work and fine for me.... I tried to plugin/out many times and didn't see the issue happen Thank you > diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c index > d749ea8250d6..c69b4ce5dbfd 100644 > --- a/drivers/pci/remove.c > +++ b/drivers/pci/remove.c > @@ -1,6 +1,7 @@ > // SPDX-License-Identifier: GPL-2.0 > #include <linux/pci.h> > #include <linux/module.h> > +#include <linux/pm_runtime.h> > #include "pci.h" > > static void pci_free_resources(struct pci_dev *dev) @@ -18,6 +19,7 @@ > static void pci_stop_dev(struct pci_dev *dev) > pci_pme_active(dev, false); > > if (pci_dev_is_added(dev)) { > + pm_runtime_barrier(&dev->dev); > > device_release_driver(&dev->dev); > pci_proc_detach_device(dev); > > > > [...] > > [ 360.771161] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ > > 360.771165] pcieport 0000:00:1c.0: pciehp: Slot(8): Card not present [ > > 361.986932] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present [ > > 361.986937] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up [ > > 362.120635] pci 0000:01:00.0: [15b7:5007] type 00 class 0x010802 [ > > 362.120691] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff > > 64bit] [ 362.120747] pci 0000:01:00.0: reg 0x20: [mem > > 0x00000000-0x000000ff 64bit] [ 362.121606] pci 0000:01:00.0: BAR 0: > > assigned [mem 0xa3b00000-0xa3b03fff 64bit] [ 362.121646] pci > > 0000:01:00.0: BAR 4: assigned [mem 0xa3b04000-0xa3b040ff 64bit] > [ 362.121686] pcieport 0000:00:1c.0: PCI bridge to [bus 01] > > [ 362.121702] pcieport 0000:00:1c.0: bridge window [io > 0x4000-0x4fff] > > [ 362.121743] pcieport 0000:00:1c.0: bridge window [mem > 0xa3b00000-0xa44fffff] > > [ 362.121761] pcieport 0000:00:1c.0: bridge window [mem > 0xa0a00000-0xa13fffff 64bit pref] > > [ 362.171709] nvme nvme0: pci function 0000:01:00.0 [ 362.171726] > > nvme 0000:01:00.0: enabling device (0000 -> 0002) [ 362.256724] nvme > > nvme0: 4/0/0 default/read/poll queues [ 362.261656] nvme0n1: p1 p2 [ > > 369.343246] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ > > 369.457450] pcieport 0000:00:1c.0: pciehp: Slot(8): Card present [ > > 369.457462] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Up [ > > 369.592600] pci 0000:01:00.0: [10ec:5261] type 00 class 0xff0000 [ > > 369.592654] pci 0000:01:00.0: reg 0x10: [mem 0xa3b00000-0xa3b00fff] [ > > 369.592776] pci 0000:01:00.0: Upstream bridge's Max Payload Size set > > to 128 (was 256, max 256) [ 369.592797] pci 0000:01:00.0: Max Payload > > Size set to 128 (was 128, max 128) [ 369.592964] pci 0000:01:00.0: > > supports D1 D2 [ 369.592970] pci 0000:01:00.0: PME# supported from D1 > > D2 D3hot D3cold [ 369.593642] pci 0000:01:00.0: BAR 0: assigned [mem > > 0xa3b00000-0xa3b00fff] [ 369.593662] pcieport 0000:00:1c.0: PCI bridge to > [bus 01] > > [ 369.593679] pcieport 0000:00:1c.0: bridge window [io > 0x4000-0x4fff] > > [ 369.593692] pcieport 0000:00:1c.0: bridge window [mem > 0xa3b00000-0xa44fffff] > > [ 369.593703] pcieport 0000:00:1c.0: bridge window [mem > 0xa0a00000-0xa13fffff 64bit pref] > > [ 372.573757] pcieport 0000:00:1c.0: pciehp: Slot(8): Link Down [ > > 372.586620] BUG: unable to handle page fault for address: > > ffffc90000089010 [ 372.586624] #PF: supervisor read access in kernel > > mode [ 372.586626] #PF: error_code(0x0000) - not-present page [ > > 372.586627] PGD 100000067 P4D 100000067 PUD 10020a067 PMD > 10020b067 > > PTE 0 [ 372.586632] Oops: 0000 [#1] PREEMPT SMP PTI [ 372.586634] > > CPU: 2 PID: 157 Comm: kworker/2:2 Not tainted 6.6.0-rc4 #12 [ > > 372.586637] Hardware name: To Be Filled By O.E.M. To Be Filled By > > O.E.M./H370M Pro4, BIOS P3.40 10/25/2018 [ 372.586639] Workqueue: > pm > > pm_runtime_work [ 372.586644] RIP: 0010:ioread32+0x2e/0x70 [ > > 372.586647] Code: ff 03 00 77 25 48 81 ff 00 00 01 00 77 14 8b 15 98 > > ac 52 01 b8 ff ff ff ff 85 d2 75 14 c3 cc cc cc cc 89 fa ed c3 cc cc > > cc cc <8b> 07 c3 cc cc cc cc 55 83 ea 01 48 89 fe 48 c7 c7 f8 97 57 86 > > 48 [ 372.586649] RSP: 0018:ffffc90000543d50 EFLAGS: 00010296 [ > > 372.586652] RAX: ffffc90000089000 RBX: 000000000000032f RCX: > > 000000000000007f [ 372.586653] RDX: 000000000000ff00 RSI: > > ffffc90000089010 RDI: ffffc90000089010 [ 372.586655] RBP: > > ffffc90000543d70 R08: ffffc90000089010 R09: ffff88816a132368 [ > > 372.586656] R10: 0000000000000000 R11: 0000000000000003 R12: > > 000000000000007f [ 372.586657] R13: ffff8881060ed000 R14: > > ffff8881060ed100 R15: 0000000000009003 [ 372.586659] FS: > 0000000000000000(0000) GS:ffff88816a100000(0000) > knlGS:0000000000000000 [ 372.586661] CS: 0010 DS: 0000 ES: 0000 CR0: > 0000000080050033 [ 372.586662] CR2: ffffc90000089010 CR3: > 0000000043032006 CR4: 00000000003706e0 [ 372.586664] Call Trace: > > [ 372.586665] <TASK> > > [ 372.586667] ? show_regs+0x68/0x70 > > [ 372.586671] ? __die_body+0x20/0x70 [ 372.586674] ? > > __die+0x2b/0x40 [ 372.586677] ? page_fault_oops+0x160/0x480 [ > > 372.586680] ? search_bpf_extables+0x63/0x90 [ 372.586684] ? > > ioread32+0x2e/0x70 [ 372.586686] ? search_exception_tables+0x5f/0x70 > > [ 372.586689] ? kernelmode_fixup_or_oops+0xa2/0x120 > > [ 372.586692] ? __bad_area_nosemaphore+0x179/0x230 > > [ 372.586696] ? bad_area_nosemaphore+0x16/0x20 [ 372.586698] ? > > do_kern_addr_fault+0x8b/0xa0 [ 372.586701] ? > > exc_page_fault+0xe5/0x180 [ 372.586705] ? > > asm_exc_page_fault+0x27/0x30 [ 372.586710] ? ioread32+0x2e/0x70 [ > > 372.586714] ? rtsx_pci_write_register+0x5b/0x90 [rtsx_pci] [ > > 372.586723] rtsx_set_l1off_sub+0x1c/0x30 [rtsx_pci] [ 372.586731] > > rts5261_set_l1off_cfg_sub_d0+0x36/0x40 [rtsx_pci] [ 372.586740] > > rtsx_pci_runtime_idle+0xc7/0x160 [rtsx_pci] [ 372.586748] ? > > __pfx_pci_pm_runtime_idle+0x10/0x10 > > [ 372.586751] pci_pm_runtime_idle+0x34/0x70 [ 372.586753] > > rpm_idle+0xc4/0x2b0 [ 372.586756] pm_runtime_work+0x93/0xc0 [ > > 372.586759] process_scheduled_works+0x9a/0x390 > > [ 372.586762] ? __pfx_worker_thread+0x10/0x10 [ 372.586764] > > worker_thread+0x15b/0x2d0 [ 372.586767] ? > > __pfx_worker_thread+0x10/0x10 [ 372.586769] kthread+0x106/0x140 [ > > 372.586771] ? __pfx_kthread+0x10/0x10 [ 372.586774] > > ret_from_fork+0x39/0x60 [ 372.586776] ? __pfx_kthread+0x10/0x10 [ > > 372.586778] ret_from_fork_asm+0x1b/0x30 [ 372.586783] </TASK> [ > > 372.586784] Modules linked in: nvme nvme_core snd_hda_codec_hdmi > > snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio > > nls_iso8859_1 snd_sof_pci_intel_cnl snd_sof_intel_hda_common > > snd_soc_hdac_hda soundwire_intel soundwire_generic_allocation > > snd_sof_intel_hda_mlink soundwire_cadence snd_sof_intel_hda > > snd_sof_pci snd_sof_xtensa_dsp snd_sof snd_sof_utils snd_hda_ext_core > > snd_soc_acpi_intel_match snd_soc_acpi soundwire_bus intel_rapl_msr > > intel_rapl_common snd_soc_core x86_pkg_temp_thermal intel_powerclamp > > coretemp snd_compress ac97_bus kvm_intel snd_pcm_dmaengine i915 > > snd_hda_intel snd_intel_dspcfg snd_intel_sdw_acpi kvm snd_hda_codec > > snd_hda_core mei_hdcp crct10dif_pclmul ghash_clmulni_intel snd_hwdep > > snd_pcm sha512_ssse3 aesni_intel snd_seq_midi crypto_simd > > snd_seq_midi_event cryptd rapl snd_rawmidi intel_cstate drm_buddy > > binfmt_misc ttm snd_seq drm_display_helper joydev input_leds cec > > snd_seq_device wmi_bmof snd_timer ee1004 mei_me rc_core snd > > drm_kms_helper mei intel_pch_thermal i2c_algo_bit soundcore mac_hid [ > > 372.586834] acpi_tad acpi_pad sch_fq_codel msr parport_pc ppdev lp > > parport drm ramoops reed_solomon efi_pstore ip_tables x_tables autofs4 > > hid_generic usbhid hid rtsx_pci_sdmmc ahci i2c_i801 e1000e > > crc32_pclmul rtsx_pci i2c_smbus xhci_pci libahci xhci_pci_renesas > > video wmi [ 372.586856] CR2: ffffc90000089010 [ 372.586858] ---[ end > > trace 0000000000000000 ]--- [ 372.746808] RIP: > > 0010:ioread32+0x2e/0x70 [ 372.746816] Code: ff 03 00 77 25 48 81 ff > > 00 00 01 00 77 14 8b 15 98 ac 52 01 b8 ff ff ff ff 85 d2 75 14 c3 cc > > cc cc cc 89 fa ed c3 cc cc cc cc <8b> 07 c3 cc cc cc cc 55 83 ea 01 48 > > 89 fe 48 c7 c7 f8 97 57 86 48 [ 372.746818] RSP: > > 0018:ffffc90000543d50 EFLAGS: 00010296 [ 372.746821] RAX: > > ffffc90000089000 RBX: 000000000000032f RCX: 000000000000007f [ > > 372.746823] RDX: 000000000000ff00 RSI: ffffc90000089010 RDI: > > ffffc90000089010 [ 372.746825] RBP: ffffc90000543d70 R08: > > ffffc90000089010 R09: ffff88816a132368 [ 372.746826] R10: > > 0000000000000000 R11: 0000000000000003 R12: 000000000000007f [ > > 372.746828] R13: ffff8881060ed000 R14: ffff8881060ed100 R15: > > 0000000000009003 [ 372.746830] FS: 0000000000000000(0000) > > GS:ffff88816a100000(0000) knlGS:0000000000000000 [ 372.746832] CS: > > 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 372.746833] CR2: > > ffffc90000089010 CR3: 000000010a564004 CR4: 00000000003706e0 [ > > 372.746835] note: kworker/2:2[157] exited with irqs disabled > > > > > diff --git a/drivers/pci/remove.c b/drivers/pci/remove.c index > > > d749ea8250d6..907d60587227 100644 > > > --- a/drivers/pci/remove.c > > > +++ b/drivers/pci/remove.c > > > @@ -1,6 +1,7 @@ > > > // SPDX-License-Identifier: GPL-2.0 #include <linux/pci.h> > > > #include <linux/module.h> > > > +#include <linux/pm_runtime.h> > > > #include "pci.h" > > > > > > static void pci_free_resources(struct pci_dev *dev) @@ -89,6 +90,8 > > > @@ static void pci_remove_bus_device(struct pci_dev *dev) > > > struct pci_bus *bus = dev->subordinate; > > > struct pci_dev *child, *tmp; > > > > > > + pm_runtime_barrier(&dev->dev); > > > + > > > if (bus) { > > > list_for_each_entry_safe(child, tmp, > > > &bus->devices, bus_list) > > > > > > > >
diff --git a/drivers/pci/hotplug/pciehp_pci.c b/drivers/pci/hotplug/pciehp_pci.c index ad12515a4a12..9ae4fa95c8c1 100644 --- a/drivers/pci/hotplug/pciehp_pci.c +++ b/drivers/pci/hotplug/pciehp_pci.c @@ -18,9 +18,18 @@ #include <linux/kernel.h> #include <linux/types.h> #include <linux/pci.h> +#include <linux/pm_runtime.h> #include "../pci.h" #include "pciehp.h" +int pci_dev_disconnect(struct pci_dev *pdev, void *unused) +{ + pm_runtime_barrier(&pdev->dev); + pci_dev_set_disconnected(pdev, NULL); + + return 0; +} + /** * pciehp_configure_device() - enumerate PCI devices below a hotplug bridge * @ctrl: PCIe hotplug controller @@ -98,7 +107,7 @@ void pciehp_unconfigure_device(struct controller *ctrl, bool presence) __func__, pci_domain_nr(parent), parent->number); if (!presence) - pci_walk_bus(parent, pci_dev_set_disconnected, NULL); + pci_walk_bus(parent, pci_dev_disconnect, NULL); pci_lock_rescan_remove();