[RFC,6/8] arm64: dts: qcom: sm8650: add interconnect dependent device nodes

Commit Message

Neil Armstrong Oct. 25, 2023, 7:47 a.m. UTC

Add Hardware nodes that depends on an interconnect property to
be valid.

The includes:
- all QUP i2s/spi nodes
- PCIe
- UFS
- SDHCI
- Display
- HWMON

Signed-off-by: Neil Armstrong <[e-mail]>
---
 arch/arm64/boot/dts/qcom/sm8650.dtsi | 3348 +++++++++++++++++++++++++++++++---
 1 file changed, 3083 insertions(+), 265 deletions(-)

Comments

Konrad Dybcio Oct. 25, 2023, 9:10 a.m. UTC | #1

On 10/25/23 09:47, Neil Armstrong wrote:
> Add Hardware nodes that depends on an interconnect property to
> be valid.
> 
> The includes:
> - all QUP i2s/spi nodes
> - PCIe
> - UFS
> - SDHCI
> - Display
> - HWMON
> 
> Signed-off-by: Neil Armstrong <[e-mail]>
> ---
QCOM_ICC_TAG_ALWAYS would be nice.. (see sa8775p)

[...]

> +			/* Forbid SDR104/SDR50 - broken hw! */
> +			sdhci-caps-mask = <0x3 0>;
Have they *still* not fixed that?

[...]

There's a whole lot to digest here, but I don't see anything
obviously wrong..

Acked-by: Konrad Dybcio <[e-mail]>

Konrad

Neil Armstrong Oct. 25, 2023, 11:52 a.m. UTC | #2

On 25/10/2023 11:10, Konrad Dybcio wrote:
> 
> 
> On 10/25/23 09:47, Neil Armstrong wrote:
>> Add Hardware nodes that depends on an interconnect property to
>> be valid.
>>
>> The includes:
>> - all QUP i2s/spi nodes
>> - PCIe
>> - UFS
>> - SDHCI
>> - Display
>> - HWMON
>>
>> Signed-off-by: Neil Armstrong <[e-mail]>
>> ---
> QCOM_ICC_TAG_ALWAYS would be nice.. (see sa8775p)

I'll add those,

Thanks,
Neil

> 
> [...]
> 
>> +            /* Forbid SDR104/SDR50 - broken hw! */
>> +            sdhci-caps-mask = <0x3 0>;
> Have they *still* not fixed that?
> 
> [...]
> 
> There's a whole lot to digest here, but I don't see anything
> obviously wrong..
> 
> Acked-by: Konrad Dybcio <[e-mail]>
> 
> Konrad

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8650.dtsi b/arch/arm64/boot/dts/qcom/sm8650.dtsi
index bbebe15437aa..0b5ff539959a 100644
--- a/arch/arm64/boot/dts/qcom/sm8650.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8650.dtsi
@@ -11,6 +11,7 @@ 
 #include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/firmware/qcom,scm.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interconnect/qcom,sm8650-rpmh.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/phy/phy-qcom-qmp.h>
@@ -57,6 +58,11 @@  bi_tcxo_ao_div2: bi-tcxo-ao-div2-clk {
 			clock-mult = <1>;
 			clock-div = <2>;
 		};
+
+		pcie_1_phy_aux_clk: pcie-1-phy-aux-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
 	};
 
 	cpus {
@@ -363,9 +369,22 @@  CLUSTER_SLEEP_1: cluster-sleep-1 {
 	firmware {
 		scm: scm {
 			compatible = "qcom,scm-sm8650", "qcom,scm";
+			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
 		};
 	};
 
+	clk_virt: interconnect-0 {
+		compatible = "qcom,sm8650-clk-virt";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	mc_virt: interconnect-1 {
+		compatible = "qcom,sm8650-mc-virt";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
 	memory@a0000000 {
 		device_type = "memory";
 		/* We expect the bootloader to fill in the size */
@@ -626,6 +645,95 @@  llcc_lpi_mem: llcc-lpi@ff800000 {
 		};
 	};
 
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+
+		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&ipcc IPCC_CLIENT_LPASS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,smem = <443>, <429>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		smp2p_adsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_adsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-cdsp {
+		compatible = "qcom,smp2p";
+
+		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&ipcc IPCC_CLIENT_CDSP
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,smem = <94>, <432>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <5>;
+
+		smp2p_cdsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_cdsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-modem {
+		compatible = "qcom,smp2p";
+
+		interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+
+		mboxes = <&ipcc IPCC_CLIENT_MPSS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,smem = <435>, <428>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		smp2p_modem_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_modem_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		ipa_smp2p_out: ipa-ap-to-modem {
+			qcom,entry-name = "ipa";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		ipa_smp2p_in: ipa-modem-to-ap {
+			qcom,entry-name = "ipa";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
 	soc: soc@0 {
 		compatible = "simple-bus";
 
@@ -641,13 +749,13 @@  gcc: clock-controller@100000 {
 			clocks = <&bi_tcxo_div2>,
 				 <&bi_tcxo_ao_div2>,
 				 <&sleep_clk>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>,
-				 <0>;
+				 <&pcie0_phy>,
+				 <&pcie1_phy>,
+				 <&pcie_1_phy_aux_clk>,
+				 <&ufs_mem_phy 0>,
+				 <&ufs_mem_phy 1>,
+				 <&ufs_mem_phy 2>,
+				 <&usb_dp_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
 
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -712,240 +820,2195 @@  qupv3_id_1: geniqup@8c0000 {
 
 			status = "disabled";
 
-			uart15: serial@89c000 {
-				compatible = "qcom,geni-debug-uart";
-				reg = <0 0x0089c000 0 0x4000>;
+			i2c8: i2c@880000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00880000 0 0x4000>;
 
-				interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
 
-				clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
 				clock-names = "se";
 
-				pinctrl-0 = <&qup_uart15_default>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c8_data_clk>;
 				pinctrl-names = "default";
 
+				#address-cells = <1>;
+				#size-cells = <0>;
+
 				status = "disabled";
 			};
-		};
 
-		gpi_dma1: dma-controller@a00000 {
-			compatible = "qcom,sm8650-gpi-dma", "qcom,sm6350-gpi-dma";
-			reg = <0 0x00a00000 0 0x60000>;
+			spi8: spi@880000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00880000 0 0x4000>;
 
-			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
 
-			dma-channels = <12>;
-			dma-channel-mask = <0xc>;
-			#dma-cells = <3>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				clock-names = "se";
 
-			iommus = <&apps_smmu 0xb6 0>;
-			dma-coherent;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 
-			status = "disabled";
-		};
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
 
-		rng: rng@10c3000 {
-			compatible = "qcom,sm8650-trng", "qcom,trng";
-			reg = <0 0x010c3000 0 0x1000>;
-		};
+				pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
+				pinctrl-names = "default";
 
-		ice: crypto@1d88000 {
-			compatible = "qcom,sm8650-inline-crypto-engine",
-				     "qcom,inline-crypto-engine";
-			reg = <0 0x01d88000 0 0x8000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 
-			clocks = <&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
-		};
+				status = "disabled";
+			};
 
-		tcsr_mutex: hwlock@1f40000 {
-			compatible = "qcom,tcsr-mutex";
-			reg = <0 0x01f40000 0 0x20000>;
+			i2c9: i2c@884000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00884000 0 0x4000>;
 
-			#hwlock-cells = <1>;
-		};
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
 
-		tcsr: clock-controller@1fc0000 {
-			compatible = "qcom,sm8650-tcsr", "syscon";
-			reg = <0 0x01fc0000 0 0xa0000>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				clock-names = "se";
 
-			clocks = <&rpmhcc RPMH_CXO_CLK>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
 
-		gpucc: clock-controller@3d90000 {
-			compatible = "qcom,sm8650-gpucc";
-			reg = <0 0x03d90000 0 0xa000>;
+				pinctrl-0 = <&qup_i2c9_data_clk>;
+				pinctrl-names = "default";
 
-			clocks = <&bi_tcxo_div2>,
-				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
-				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-		};
+				status = "disabled";
+			};
 
-		dispcc: clock-controller@af00000 {
-			compatible = "qcom,sm8650-dispcc";
-			reg = <0 0x0af00000 0 0x20000>;
+			spi9: spi@884000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00884000 0 0x4000>;
 
-			clocks = <&bi_tcxo_div2>,
-				 <&bi_tcxo_ao_div2>,
-				 <&gcc GCC_DISP_AHB_CLK>,
-				 <&sleep_clk>,
-				 <0>, /* dsi0 */
-				 <0>,
-				 <0>, /* dsi1 */
-				 <0>,
-				 <0>, /* dp0 */
-				 <0>,
-				 <0>, /* dp1 */
-				 <0>,
-				 <0>, /* dp2 */
-				 <0>,
-				 <0>, /* dp3 */
-				 <0>;
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
 
-			power-domains = <&rpmhpd RPMHPD_MMCX>;
-			required-opps = <&rpmhpd_opp_low_svs>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				clock-names = "se";
 
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 
-			status = "disabled";
-		};
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
 
-		usb_1_hsphy: phy@88e3000 {
-			compatible = "qcom,sm8650-snps-eusb2-phy",
-				     "qcom,sm8550-snps-eusb2-phy";
-			reg = <0 0x088e3000 0 0x154>;
+				pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
+				pinctrl-names = "default";
 
-			clocks = <&tcsr TCSR_USB2_CLKREF_EN>;
-			clock-names = "ref";
+				#address-cells = <1>;
+				#size-cells = <0>;
 
-			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+				status = "disabled";
+			};
 
-			#phy-cells = <0>;
+			i2c10: i2c@888000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00888000 0 0x4000>;
 
-			status = "disabled";
-		};
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
 
-		usb_dp_qmpphy: phy@88e8000 {
-			compatible = "qcom,sm8650-qmp-usb3-dp-phy";
-			reg = <0 0x088e8000 0 0x3000>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				clock-names = "se";
 
-			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
-				 <&rpmhcc RPMH_CXO_CLK>,
-				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
-				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
-			clock-names = "aux",
-				      "ref",
-				      "com_aux",
-				      "usb3_pipe";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 
-			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
-				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
-			reset-names = "phy",
-				      "common";
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
 
-			power-domains = <&gcc USB3_PHY_GDSC>;
+				pinctrl-0 = <&qup_i2c10_data_clk>;
+				pinctrl-names = "default";
 
-			#clock-cells = <1>;
-			#phy-cells = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 
-			status = "disabled";
-		};
+				status = "disabled";
+			};
 
-		usb_1: usb@a6f8800 {
-			compatible = "qcom,sm8650-dwc3", "qcom,dwc3";
-			reg = <0 0x0a6f8800 0 0x400>;
+			spi10: spi@888000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00888000 0 0x4000>;
 
-			interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 15 IRQ_TYPE_EDGE_RISING>,
-					      <&pdc 14 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "hs_phy_irq",
-					  "ss_phy_irq",
-					  "dm_hs_phy_irq",
-					  "dp_hs_phy_irq";
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
 
-			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
-				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-				 <&tcsr TCSR_USB3_CLKREF_EN>;
-			clock-names = "cfg_noc",
-				      "core",
-				      "iface",
-				      "sleep",
-				      "mock_utmi",
-				      "xo";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				clock-names = "se";
 
-			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
-			assigned-clock-rates = <19200000>, <200000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 
-			resets = <&gcc GCC_USB30_PRIM_BCR>;
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
 
-			power-domains = <&gcc USB30_PRIM_GDSC>;
-			required-opps = <&rpmhpd_opp_nom>;
+				pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
+				pinctrl-names = "default";
 
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+				#address-cells = <1>;
+				#size-cells = <0>;
 
-			status = "disabled";
+				status = "disabled";
+			};
 
-			usb_1_dwc3: usb@a600000 {
-				compatible = "snps,dwc3";
-				reg = <0 0x0a600000 0 0xcd00>;
+			i2c11: i2c@88c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0088c000 0 0x4000>;
 
-				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
 
-				iommus = <&apps_smmu 0x40 0>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				clock-names = "se";
 
-				phys = <&usb_1_hsphy>,
-				       <&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
-				phy-names = "usb2-phy",
-					    "usb3-phy";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
 
-				snps,hird-threshold = /bits/ 8 <0x0>;
-				snps,usb2-gadget-lpm-disable;
-				snps,dis_u2_susphy_quirk;
-				snps,dis_enblslpm_quirk;
-				snps,dis-u1-entry-quirk;
-				snps,dis-u2-entry-quirk;
-				snps,is-utmi-l1-suspend;
-				snps,usb3_lpm_capable;
-				snps,usb2-lpm-disable;
-				snps,has-lpm-erratum;
-				tx-fifo-resize;
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
 
-				dma-coherent;
+				pinctrl-0 = <&qup_i2c11_data_clk>;
+				pinctrl-names = "default";
 
-				ports {
-					#address-cells = <1>;
-					#size-cells = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 
-					port@0 {
-						reg = <0>;
+				status = "disabled";
+			};
 
-						usb_1_dwc3_hs: endpoint {
+			spi11: spi@88c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0088c000 0 0x4000>;
+
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c12: i2c@890000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00890000 0 0x4000>;
+
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c12_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi12: spi@890000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00890000 0 0x4000>;
+
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c13: i2c@894000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00894000 0 0x4000>;
+
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c13_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi13: spi@894000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00894000 0 0x4000>;
+
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			uart14: serial@898000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00898000 0 0x4000>;
+
+				interrupts = <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
+				clock-names = "se";
+
+				interconnects =	<&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&qup_uart14_default>, <&qup_uart14_cts_rts>;
+				pinctrl-names = "default";
+
+				status = "disabled";
+			};
+
+			uart15: serial@89c000 {
+				compatible = "qcom,geni-debug-uart";
+				reg = <0 0x0089c000 0 0x4000>;
+
+				interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP2_S7_CLK>;
+				clock-names = "se";
+
+				interconnects =	<&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&qup_uart15_default>;
+				pinctrl-names = "default";
+
+				status = "disabled";
+			};
+		};
+
+		i2c_master_hub_0: geniqup@9c0000 {
+			compatible = "qcom,geni-se-i2c-master-hub";
+			reg = <0 0x009c0000 0 0x2000>;
+
+			clocks = <&gcc GCC_QUPV3_I2C_S_AHB_CLK>;
+			clock-names = "s-ahb";
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			i2c_hub_0: i2c@980000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x00980000 0 0x4000>;
+
+				interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S0_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c0_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_1: i2c@984000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x00984000 0 0x4000>;
+
+				interrupts = <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S1_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c1_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_2: i2c@988000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x00988000 0 0x4000>;
+
+				interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S2_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c2_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_3: i2c@98c000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x0098c000 0 0x4000>;
+
+				interrupts = <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S3_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c3_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_4: i2c@990000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x00990000 0 0x4000>;
+
+				interrupts = <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S4_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c4_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_5: i2c@994000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x00994000 0 0x4000>;
+
+				interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S5_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c5_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_6: i2c@998000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x00998000 0 0x4000>;
+
+				interrupts = <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S6_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c6_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_7: i2c@99c000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x0099c000 0 0x4000>;
+
+				interrupts = <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S7_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c7_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_8: i2c@9a0000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x009a0000 0 0x4000>;
+
+				interrupts = <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S8_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c8_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c_hub_9: i2c@9a4000 {
+				compatible = "qcom,geni-i2c-master-hub";
+				reg = <0 0x009a4000 0 0x4000>;
+
+				interrupts = <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_I2C_S9_CLK>,
+					 <&gcc GCC_QUPV3_I2C_CORE_CLK>;
+				clock-names = "se",
+					      "core";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_I2C 0>;
+				interconnect-names = "qup-core",
+						     "qup-config";
+
+				pinctrl-0 = <&hub_i2c9_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		gpi_dma1: dma-controller@a00000 {
+			compatible = "qcom,sm8650-gpi-dma", "qcom,sm6350-gpi-dma";
+			reg = <0 0x00a00000 0 0x60000>;
+
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+
+			dma-channels = <12>;
+			dma-channel-mask = <0xc>;
+			#dma-cells = <3>;
+
+			iommus = <&apps_smmu 0xb6 0>;
+			dma-coherent;
+
+			status = "disabled";
+		};
+
+		qupv3_id_0: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x00ac0000 0 0x2000>;
+
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			clock-names = "m-ahb",
+				      "s-ahb";
+
+			interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>;
+			interconnect-names = "qup-core";
+
+			iommus = <&apps_smmu 0xa3 0>;
+
+			dma-coherent;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			i2c0: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a80000 0 0x4000>;
+
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi0: spi@a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a80000 0 0x4000>;
+
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c1: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a84000 0 0x4000>;
+
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi1: spi@a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a84000 0 0x4000>;
+
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c2: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a88000 0 0x4000>;
+
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c2_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi2: spi@a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a88000 0 0x4000>;
+
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c3: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a8c000 0 0x4000>;
+
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c3_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi3: spi@a8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a8c000 0 0x4000>;
+
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c4: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a90000 0 0x4000>;
+
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c4_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi4: spi@a90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a90000 0 0x4000>;
+
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c5: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c5_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi5: spi@a94000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a94000 0 0x4000>;
+
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c6: i2c@a98000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a98000 0 0x4000>;
+
+				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c6_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi6: spi@a98000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a98000 0 0x4000>;
+
+				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			i2c7: i2c@a9c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a9c000 0 0x4000>;
+
+				interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 7 QCOM_GPI_I2C>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_i2c7_data_clk>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			spi7: spi@a9c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a9c000 0 0x4000>;
+
+				interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GCC_QUPV3_WRAP1_S7_CLK>;
+				clock-names = "se";
+
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre1_noc MASTER_QUP_1 0 &mc_virt  SLAVE_EBI1 0>;
+				interconnect-names = "qup-core",
+						     "qup-config",
+						     "qup-memory";
+
+				dmas = <&gpi_dma1 0 7 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 7 QCOM_GPI_SPI>;
+				dma-names = "tx",
+					    "rx";
+
+				pinctrl-0 = <&qup_spi7_data_clk>, <&qup_spi7_cs>;
+				pinctrl-names = "default";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		cnoc_main: interconnect@1500000 {
+			compatible = "qcom,sm8650-cnoc-main";
+			reg = <0 0x01500000 0 0x14080>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
+		config_noc: interconnect@1600000 {
+			compatible = "qcom,sm8650-config-noc";
+			reg = <0 0x01600000 0 0x6200>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
+		system_noc: interconnect@1680000 {
+			compatible = "qcom,sm8650-system-noc";
+			reg = <0 0x01680000 0 0x1d080>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
+		pcie_noc: interconnect@16c0000 {
+			compatible = "qcom,sm8650-pcie-anoc";
+			reg = <0 0x016c0000 0 0x12200>;
+
+			clocks = <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>,
+				 <&gcc GCC_CFG_NOC_PCIE_ANOC_AHB_CLK>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
+		aggre1_noc: interconnect@16e0000 {
+			compatible = "qcom,sm8650-aggre1-noc";
+			reg = <0 0x016e0000 0 0x16400>;
+
+			clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
+		aggre2_noc: interconnect@1700000 {
+			compatible = "qcom,sm8650-aggre2-noc";
+			reg = <0 0x01700000 0 0x1e400>;
+
+			clocks = <&rpmhcc RPMH_IPA_CLK>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
+		mmss_noc: interconnect@1780000 {
+			compatible = "qcom,sm8650-mmss-noc";
+			reg = <0 0x01780000 0 0x5b800>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
+		rng: rng@10c3000 {
+			compatible = "qcom,sm8650-trng", "qcom,trng";
+			reg = <0 0x010c3000 0 0x1000>;
+		};
+
+		pcie0: pci@1c00000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-sm8650", "qcom,pcie-sm8550";
+			reg = <0 0x01c00000 0 0x3000>,
+			      <0 0x60000000 0 0xf1d>,
+			      <0 0x60000f20 0 0xa8>,
+			      <0 0x60001000 0 0x1000>,
+			      <0 0x60100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>,
+				 <&gcc GCC_CNOC_PCIE_SF_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "noc_aggr",
+				      "cnoc_sf_axi";
+
+			resets = <&gcc GCC_PCIE_0_BCR>;
+			reset-names = "pci";
+
+			interconnects = <&pcie_noc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_0 0>;
+			interconnect-names = "pcie-mem",
+					     "cpu-pcie";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+
+			iommu-map = <0     &apps_smmu 0x1400 0x1>,
+				    <0x100 &apps_smmu 0x1401 0x1>;
+
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			#interrupt-cells = <1>;
+
+			linux,pci-domain = <0>;
+			num-lanes = <2>;
+			bus-range = <0 0xff>;
+
+			phys = <&pcie0_phy>;
+			phy-names = "pciephy";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0 0x00000000 0 0x60200000 0 0x100000>,
+				 <0x02000000 0 0x60300000 0 0x60300000 0 0x3d00000>;
+
+			dma-coherent;
+
+			status = "disabled";
+		};
+
+		pcie0_phy: phy@1c06000 {
+			compatible = "qcom,sm8650-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c06000 0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_0_CLKREF_EN>,
+				 <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_0_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "rchng",
+				      "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+			reset-names = "phy";
+
+			power-domains = <&gcc PCIE_0_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie0_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		pcie1: pci@1c08000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-sm8650", "qcom,pcie-sm8550";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x40000000 0 0xf1d>,
+			      <0 0x40000f20 0 0xa8>,
+			      <0 0x40001000 0 0x1000>,
+			      <0 0x40100000 0 0x100000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config";
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>,
+				 <&gcc GCC_CNOC_PCIE_SF_AXI_CLK>;
+			clock-names = "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "noc_aggr",
+				      "cnoc_sf_axi";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>,
+				 <&gcc GCC_PCIE_1_LINK_DOWN_BCR>;
+			reset-names = "pci",
+				      "link_down";
+
+			interconnects = <&pcie_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &cnoc_main SLAVE_PCIE_1 0>;
+			interconnect-names = "pcie-mem",
+					     "cpu-pcie";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+
+			iommu-map = <0     &apps_smmu 0x1480 0x1>,
+				    <0x100 &apps_smmu 0x1481 0x1>;
+
+			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			#interrupt-cells = <1>;
+
+			linux,pci-domain = <1>;
+			num-lanes = <2>;
+			bus-range = <0 0xff>;
+
+			phys = <&pcie1_phy>;
+			phy-names = "pciephy";
+
+			dma-coherent;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0 0x00000000 0 0x40200000 0 0x100000>,
+				 <0x02000000 0 0x40300000 0 0x40300000 0 0x1fd00000>;
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0e000 {
+			compatible = "qcom,sm8650-qmp-gen4x2-pcie-phy";
+			reg = <0 0x01c0e000 0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_1_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_1_CLKREF_EN>,
+				 <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_1_PIPE_CLK>;
+			clock-names = "aux",
+				      "cfg_ahb",
+				      "ref",
+				      "rchng",
+				      "pipe";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>,
+				 <&gcc GCC_PCIE_1_NOCSR_COM_PHY_BCR>;
+			reset-names = "phy",
+				      "phy_nocsr";
+
+			power-domains = <&gcc PCIE_1_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie1_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		cryptobam: dma-controller@1dc4000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0 0x01dc4000 0 0x28000>;
+
+			interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
+
+			#dma-cells = <1>;
+
+			iommus = <&apps_smmu 0x480 0>,
+				 <&apps_smmu 0x481 0>;
+
+			qcom,ee = <0>;
+			qcom,controlled-remotely;
+		};
+
+		crypto: crypto@1dfa000 {
+			compatible = "qcom,sm8650-qce", "qcom,sm8150-qce", "qcom,qce";
+			reg = <0 0x01dfa000 0 0x6000>;
+
+			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "memory";
+
+			dmas = <&cryptobam 4>, <&cryptobam 5>;
+			dma-names = "rx", "tx";
+
+			iommus = <&apps_smmu 0x480 0>,
+				 <&apps_smmu 0x481 0>;
+		};
+
+		ufs_mem_phy: phy@1d80000 {
+			compatible = "qcom,sm8650-qmp-ufs-phy";
+			reg = <0 0x01d80000 0 0x2000>;
+
+			clocks = <&tcsr TCSR_UFS_CLKREF_EN>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+			clock-names = "ref",
+				      "ref_aux";
+
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+
+			power-domains = <&gcc UFS_MEM_PHY_GDSC>;
+
+			#clock-cells = <1>;
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ufs_mem_hc: ufs@1d84000 {
+			compatible = "qcom,sm8650-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
+			reg = <0 0x01d84000 0 0x3000>;
+
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_UFS_PHY_AHB_CLK>,
+				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				 <&tcsr TCSR_UFS_PAD_CLKREF_EN>,
+				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			clock-names = "core_clk",
+				      "bus_aggr_clk",
+				      "iface_clk",
+				      "core_clk_unipro",
+				      "ref_clk",
+				      "tx_lane0_sync_clk",
+				      "rx_lane0_sync_clk",
+				      "rx_lane1_sync_clk";
+			freq-table-hz = <100000000 403000000>,
+					<0 0>,
+					<0 0>,
+					<100000000 403000000>,
+					<100000000 403000000>,
+					<0 0>,
+					<0 0>,
+					<0 0>;
+
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+
+			interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
+			interconnect-names = "ufs-ddr",
+					     "cpu-ufs";
+
+			power-domains = <&gcc UFS_PHY_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			iommus = <&apps_smmu 0x60 0>;
+
+			lanes-per-direction = <2>;
+			qcom,ice = <&ice>;
+
+			phys = <&ufs_mem_phy>;
+			phy-names = "ufsphy";
+
+			#reset-cells = <1>;
+
+			status = "disabled";
+		};
+
+		ice: crypto@1d88000 {
+			compatible = "qcom,sm8650-inline-crypto-engine",
+				     "qcom,inline-crypto-engine";
+			reg = <0 0x01d88000 0 0x8000>;
+
+			clocks = <&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0 0x01f40000 0 0x20000>;
+
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: clock-controller@1fc0000 {
+			compatible = "qcom,sm8650-tcsr", "syscon";
+			reg = <0 0x01fc0000 0 0xa0000>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		gpucc: clock-controller@3d90000 {
+			compatible = "qcom,sm8650-gpucc";
+			reg = <0 0x03d90000 0 0xa000>;
+
+			clocks = <&bi_tcxo_div2>,
+				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
+				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
+
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		remoteproc_mpss: remoteproc@4080000 {
+			compatible = "qcom,sm8650-mpss-pas";
+			reg = <0 0x04080000 0 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack",
+					  "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			interconnects = <&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
+
+			power-domains = <&rpmhpd RPMHPD_CX>,
+					<&rpmhpd RPMHPD_MSS>;
+			power-domain-names = "cx",
+					     "mss";
+
+			memory-region = <&mpss_mem>, <&q6_mpss_dtb_mem>,
+					<&mpss_dsm_mem>, <&mpss_dsm_mem_2>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_modem_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+
+				mboxes = <&ipcc IPCC_CLIENT_MPSS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				qcom,remote-pid = <1>;
+
+				label = "mpss";
+			};
+		};
+
+		lpass_lpiaon_noc: interconnect@7400000 {
+			compatible = "qcom,sm8650-lpass-lpiaon-noc";
+			reg = <0 0x07400000 0 0x19080>;
+
+			#interconnect-cells = <2>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		lpass_lpicx_noc: interconnect@7430000 {
+			compatible = "qcom,sm8650-lpass-lpicx-noc";
+			reg = <0 0x07430000 0 0x3a200>;
+
+			#interconnect-cells = <2>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		lpass_ag_noc: interconnect@7e40000 {
+			compatible = "qcom,sm8650-lpass-ag-noc";
+			reg = <0 0x07e40000 0 0xe080>;
+
+			#interconnect-cells = <2>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		sdhc_2: mmc@8804000 {
+			compatible = "qcom,sm8650-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x08804000 0 0x1000>;
+
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq",
+					  "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface",
+				      "core",
+				      "xo";
+
+			interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
+			interconnect-names = "sdhc-ddr",
+					     "cpu-sdhc";
+
+			power-domains = <&rpmhpd RPMHPD_CX>;
+			operating-points-v2 = <&sdhc2_opp_table>;
+
+			iommus = <&apps_smmu 0x540 0>;
+
+			bus-width = <4>;
+
+			/* Forbid SDR104/SDR50 - broken hw! */
+			sdhci-caps-mask = <0x3 0>;
+
+			qcom,dll-config = <0x0007642c>;
+			qcom,ddr-config = <0x80040868>;
+
+			dma-coherent;
+
+			status = "disabled";
+
+			sdhc2_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-19200000 {
+					opp-hz = /bits/ 64 <19200000>;
+					required-opps = <&rpmhpd_opp_min_svs>;
+				};
+
+				opp-50000000 {
+					opp-hz = /bits/ 64 <50000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+				};
+
+				opp-202000000 {
+					opp-hz = /bits/ 64 <202000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
+		};
+
+		mdss: display-subsystem@ae00000 {
+			compatible = "qcom,sm8650-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				 <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
+
+			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;
+
+			interconnects = <&mmss_noc MASTER_MDP 0 &gem_noc SLAVE_LLCC 0>,
+					<&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "mdp0-mem",
+					     "mdp1-mem";
+
+			power-domains = <&dispcc MDSS_GDSC>;
+
+			iommus = <&apps_smmu 0x1c00 0x2>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: display-controller@ae01000 {
+				compatible = "qcom,sm8650-dpu";
+				reg = <0 0x0ae01000 0 0x8f000>,
+				      <0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp",
+					    "vbif";
+
+				interrupts-extended = <&mdss 0>;
+
+				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
+					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
+
+				operating-points-v2 = <&mdp_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&mdss_dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						dpu_intf2_out: endpoint {
+							remote-endpoint = <&mdss_dsi1_in>;
+						};
+					};
+				};
+
+				mdp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-325000000 {
+						opp-hz = /bits/ 64 <325000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-375000000 {
+						opp-hz = /bits/ 64 <375000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-514000000 {
+						opp-hz = /bits/ 64 <514000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dsi0: dsi@ae94000 {
+				compatible = "qcom,sm8650-dsi-ctrl", "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupts-extended = <&mdss 4>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi0_phy 0>,
+							 <&mdss_dsi0_phy 1>;
+
+				operating-points-v2 = <&mdss_dsi_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				phys = <&mdss_dsi0_phy>;
+				phy-names = "dsi";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dsi0_out: endpoint {
+						};
+					};
+				};
+
+				mdss_dsi_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+			};
+
+			mdss_dsi0_phy: phy@ae95000 {
+				compatible = "qcom,sm8650-dsi-phy-4nm";
+				reg = <0 0x0ae95000 0 0x200>,
+				      <0 0x0ae95200 0 0x280>,
+				      <0 0x0ae95500 0 0x400>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface",
+					      "ref";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				status = "disabled";
+			};
+
+			mdss_dsi1: dsi@ae96000 {
+				compatible = "qcom,sm8650-dsi-ctrl", "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae96000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupts-extended = <&mdss 5>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&mdss_dsi1_phy 0>,
+							 <&mdss_dsi1_phy 1>;
+
+				operating-points-v2 = <&mdss_dsi_opp_table>;
+
+				power-domains = <&rpmhpd RPMHPD_MMCX>;
+
+				phys = <&mdss_dsi1_phy>;
+				phy-names = "dsi";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						mdss_dsi1_in: endpoint {
+							remote-endpoint = <&dpu_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						mdss_dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			mdss_dsi1_phy: phy@ae97000 {
+				compatible = "qcom,sm8650-dsi-phy-4nm";
+				reg = <0 0x0ae97000 0 0x200>,
+				      <0 0x0ae97200 0 0x280>,
+				      <0 0x0ae97500 0 0x400>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface",
+					      "ref";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		dispcc: clock-controller@af00000 {
+			compatible = "qcom,sm8650-dispcc";
+			reg = <0 0x0af00000 0 0x20000>;
+
+			clocks = <&bi_tcxo_div2>,
+				 <&bi_tcxo_ao_div2>,
+				 <&gcc GCC_DISP_AHB_CLK>,
+				 <&sleep_clk>,
+				 <&mdss_dsi0_phy 0>,
+				 <&mdss_dsi0_phy 1>,
+				 <&mdss_dsi1_phy 0>,
+				 <&mdss_dsi1_phy 1>,
+				 <0>, /* dp0 */
+				 <0>,
+				 <0>, /* dp1 */
+				 <0>,
+				 <0>, /* dp2 */
+				 <0>,
+				 <0>, /* dp3 */
+				 <0>;
+
+			power-domains = <&rpmhpd RPMHPD_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			status = "disabled";
+		};
+
+		usb_1_hsphy: phy@88e3000 {
+			compatible = "qcom,sm8650-snps-eusb2-phy",
+				     "qcom,sm8550-snps-eusb2-phy";
+			reg = <0 0x088e3000 0 0x154>;
+
+			clocks = <&tcsr TCSR_USB2_CLKREF_EN>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb_dp_qmpphy: phy@88e8000 {
+			compatible = "qcom,sm8650-qmp-usb3-dp-phy";
+			reg = <0 0x088e8000 0 0x3000>;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+			clock-names = "aux",
+				      "ref",
+				      "com_aux",
+				      "usb3_pipe";
+
+			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
+			reset-names = "phy",
+				      "common";
+
+			power-domains = <&gcc USB3_PHY_GDSC>;
+
+			#clock-cells = <1>;
+			#phy-cells = <1>;
+
+			status = "disabled";
+		};
+
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sm8650-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+
+			interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_RISING>,
+					      <&pdc 14 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&tcsr TCSR_USB3_CLKREF_EN>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			usb_1_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+
+				iommus = <&apps_smmu 0x40 0>;
+
+				phys = <&usb_1_hsphy>,
+				       <&usb_dp_qmpphy QMP_USB43DP_USB3_PHY>;
+				phy-names = "usb2-phy",
+					    "usb3-phy";
+
+				snps,hird-threshold = /bits/ 8 <0x0>;
+				snps,usb2-gadget-lpm-disable;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,dis-u1-entry-quirk;
+				snps,dis-u2-entry-quirk;
+				snps,is-utmi-l1-suspend;
+				snps,usb3_lpm_capable;
+				snps,usb2-lpm-disable;
+				snps,has-lpm-erratum;
+				tx-fifo-resize;
+
+				dma-coherent;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						usb_1_dwc3_hs: endpoint {
 						};
 					};
 
@@ -969,115 +3032,602 @@  pdc: interrupt-controller@b220000 {
 					  <125 63 1>, <126 716 12>,
 					  <138 251 5>, <143 244 4>;
 
-			#interrupt-cells = <2>;
-			interrupt-controller;
-		};
+			#interrupt-cells = <2>;
+			interrupt-controller;
+		};
+
+		tsens0: thermal-sensor@c228000 {
+			compatible = "qcom,sm8650-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c228000 0 0x1000>, /* TM */
+			      <0 0x0c222000 0 0x1000>; /* SROT */
+
+			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 640 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow",
+					  "critical";
+
+			#qcom,sensors = <15>;
+
+			#thermal-sensor-cells = <1>;
+		};
+
+		tsens1: thermal-sensor@c229000 {
+			compatible = "qcom,sm8650-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c229000 0 0x1000>, /* TM */
+			      <0 0x0c223000 0 0x1000>; /* SROT */
+
+			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow",
+					  "critical";
+
+			#qcom,sensors = <16>;
+
+			#thermal-sensor-cells = <1>;
+		};
+
+		tsens2: thermal-sensor@c22a000 {
+			compatible = "qcom,sm8650-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c22a000 0 0x1000>, /* TM */
+			      <0 0x0c224000 0 0x1000>; /* SROT */
+
+			interrupts = <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 642 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow",
+					  "critical";
+
+			#qcom,sensors = <13>;
+
+			#thermal-sensor-cells = <1>;
+		};
+
+		aoss_qmp: power-management@c300000 {
+			compatible = "qcom,sm8650-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0 0x0c300000 0 0x400>;
+
+			interrupt-parent = <&ipcc>;
+			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
+						     IRQ_TYPE_EDGE_RISING>;
+
+			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+			#clock-cells = <0>;
+		};
+
+		sram@c3f0000 {
+			compatible = "qcom,rpmh-stats";
+			reg = <0 0x0c3f0000 0 0x400>;
+		};
+
+		spmi_bus: spmi@c400000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0 0x0c400000 0 0x3000>,
+			      <0 0x0c500000 0 0x4000000>,
+			      <0 0x0c440000 0 0x80000>,
+			      <0 0x0c4c0000 0 0x20000>,
+			      <0 0x0c42d000 0 0x4000>;
+			reg-names = "core",
+				    "chnls",
+				    "obsrvr",
+				    "intr",
+				    "cnfg";
+
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "periph_irq";
+
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			qcom,bus-id = <0>;
+
+			interrupt-controller;
+			#interrupt-cells = <4>;
+
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sm8650-tlmm";
+			reg = <0 0x0f100000 0 0x300000>;
+
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			gpio-ranges = <&tlmm 0 0 211>;
+
+			wakeup-parent = <&pdc>;
+
+			hub_i2c0_data_clk: hub-i2c0-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio64", "gpio65";
+				function = "i2chub0_se0";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c1_data_clk: hub-i2c1-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio66", "gpio67";
+				function = "i2chub0_se1";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c2_data_clk: hub-i2c2-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio68", "gpio69";
+				function = "i2chub0_se2";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c3_data_clk: hub-i2c3-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio70", "gpio71";
+				function = "i2chub0_se3";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c4_data_clk: hub-i2c4-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio72", "gpio73";
+				function = "i2chub0_se4";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c5_data_clk: hub-i2c5-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio74", "gpio75";
+				function = "i2chub0_se5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c6_data_clk: hub-i2c6-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio76", "gpio77";
+				function = "i2chub0_se6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c7_data_clk: hub-i2c7-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio78", "gpio79";
+				function = "i2chub0_se7";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c8_data_clk: hub-i2c8-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio206", "gpio207";
+				function = "i2chub0_se8";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			hub_i2c9_data_clk: hub-i2c9-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio80", "gpio81";
+				function = "i2chub0_se9";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			pcie0_default_state: pcie0-default-state {
+				perst-pins {
+					pins = "gpio94";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				clkreq-pins {
+					pins = "gpio95";
+					function = "pcie0_clk_req_n";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				wake-pins {
+					pins = "gpio96";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			pcie1_default_state: pcie1-default-state {
+				perst-pins {
+					pins = "gpio97";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				clkreq-pins {
+					pins = "gpio98";
+					function = "pcie1_clk_req_n";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				wake-pins {
+					pins = "gpio99";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			qup_i2c0_data_clk: qup-i2c0-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio32", "gpio33";
+				function = "qup1_se0";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c1_data_clk: qup-i2c1-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio36", "gpio37";
+				function = "qup1_se1";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c2_data_clk: qup-i2c2-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio40", "gpio41";
+				function = "qup1_se2";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c3_data_clk: qup-i2c3-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio44", "gpio45";
+				function = "qup1_se3";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c4_data_clk: qup-i2c4-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio48", "gpio49";
+				function = "qup1_se4";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c5_data_clk: qup-i2c5-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio52", "gpio53";
+				function = "qup1_se5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c6_data_clk: qup-i2c6-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio56", "gpio57";
+				function = "qup1_se6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c7_data_clk: qup-i2c7-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio60", "gpio61";
+				function = "qup1_se7";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c8_data_clk: qup-i2c8-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio0", "gpio1";
+				function = "qup2_se0";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c9_data_clk: qup-i2c9-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio4", "gpio5";
+				function = "qup2_se1";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c10_data_clk: qup-i2c10-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio8", "gpio9";
+				function = "qup2_se2";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c11_data_clk: qup-i2c11-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio12", "gpio13";
+				function = "qup2_se3";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c12_data_clk: qup-i2c12-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio16", "gpio17";
+				function = "qup2_se4";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c13_data_clk: qup-i2c13-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio20", "gpio21";
+				function = "qup2_se5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c14_data_clk: qup-i2c14-data-clk-state {
+				/* SDA, SCL */
+				pins = "gpio24", "gpio25";
+				function = "qup2_se6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_spi0_cs: qup-spi0-cs-state {
+				pins = "gpio35";
+				function = "qup1_se0";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio32", "gpio33", "gpio34";
+				function = "qup1_se0";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi1_cs: qup-spi1-cs-state {
+				pins = "gpio39";
+				function = "qup1_se1";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio36", "gpio37", "gpio38";
+				function = "qup1_se1";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-		tsens0: thermal-sensor@c228000 {
-			compatible = "qcom,sm8650-tsens", "qcom,tsens-v2";
-			reg = <0 0x0c228000 0 0x1000>, /* TM */
-			      <0 0x0c222000 0 0x1000>; /* SROT */
+			qup_spi2_cs: qup-spi2-cs-state {
+				pins = "gpio43";
+				function = "qup1_se2";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 640 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow",
-					  "critical";
+			qup_spi2_data_clk: qup-spi2-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio40", "gpio41", "gpio42";
+				function = "qup1_se2";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			#qcom,sensors = <15>;
+			qup_spi3_cs: qup-spi3-cs-state {
+				pins = "gpio47";
+				function = "qup1_se3";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			#thermal-sensor-cells = <1>;
-		};
+			qup_spi3_data_clk: qup-spi3-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio44", "gpio45", "gpio46";
+				function = "qup1_se3";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-		tsens1: thermal-sensor@c229000 {
-			compatible = "qcom,sm8650-tsens", "qcom,tsens-v2";
-			reg = <0 0x0c229000 0 0x1000>, /* TM */
-			      <0 0x0c223000 0 0x1000>; /* SROT */
+			qup_spi4_cs: qup-spi4-cs-state {
+				pins = "gpio51";
+				function = "qup1_se4";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow",
-					  "critical";
+			qup_spi4_data_clk: qup-spi4-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio48", "gpio49", "gpio50";
+				function = "qup1_se4";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			#qcom,sensors = <16>;
+			qup_spi5_cs: qup-spi5-cs-state {
+				pins = "gpio55";
+				function = "qup1_se5";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			#thermal-sensor-cells = <1>;
-		};
+			qup_spi5_data_clk: qup-spi5-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio52", "gpio53", "gpio54";
+				function = "qup1_se5";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-		tsens2: thermal-sensor@c22a000 {
-			compatible = "qcom,sm8650-tsens", "qcom,tsens-v2";
-			reg = <0 0x0c22a000 0 0x1000>, /* TM */
-			      <0 0x0c224000 0 0x1000>; /* SROT */
+			qup_spi6_cs: qup-spi6-cs-state {
+				pins = "gpio59";
+				function = "qup1_se6";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			interrupts = <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 642 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow",
-					  "critical";
+			qup_spi6_data_clk: qup-spi6-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio56", "gpio57", "gpio58";
+				function = "qup1_se6";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			#qcom,sensors = <13>;
+			qup_spi7_cs: qup-spi7-cs-state {
+				pins = "gpio63";
+				function = "qup1_se7";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			#thermal-sensor-cells = <1>;
-		};
+			qup_spi7_data_clk: qup-spi7-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio60", "gpio61", "gpio62";
+				function = "qup1_se7";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-		aoss_qmp: power-management@c300000 {
-			compatible = "qcom,sm8650-aoss-qmp", "qcom,aoss-qmp";
-			reg = <0 0x0c300000 0 0x400>;
+			qup_spi8_cs: qup-spi8-cs-state {
+				pins = "gpio3";
+				function = "qup2_se0";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			interrupt-parent = <&ipcc>;
-			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
-						     IRQ_TYPE_EDGE_RISING>;
+			qup_spi8_data_clk: qup-spi8-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup2_se0";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+			qup_spi9_cs: qup-spi9-cs-state {
+				pins = "gpio7";
+				function = "qup2_se1";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			#clock-cells = <0>;
-		};
+			qup_spi9_data_clk: qup-spi9-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio4", "gpio5", "gpio6";
+				function = "qup2_se1";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-		sram@c3f0000 {
-			compatible = "qcom,rpmh-stats";
-			reg = <0 0x0c3f0000 0 0x400>;
-		};
+			qup_spi10_cs: qup-spi10-cs-state {
+				pins = "gpio11";
+				function = "qup2_se2";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-		spmi_bus: spmi@c400000 {
-			compatible = "qcom,spmi-pmic-arb";
-			reg = <0 0x0c400000 0 0x3000>,
-			      <0 0x0c500000 0 0x4000000>,
-			      <0 0x0c440000 0 0x80000>,
-			      <0 0x0c4c0000 0 0x20000>,
-			      <0 0x0c42d000 0 0x4000>;
-			reg-names = "core",
-				    "chnls",
-				    "obsrvr",
-				    "intr",
-				    "cnfg";
+			qup_spi10_data_clk: qup-spi10-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio8", "gpio9", "gpio10";
+				function = "qup2_se2";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "periph_irq";
+			qup_spi11_cs: qup-spi11-cs-state {
+				pins = "gpio15";
+				function = "qup2_se3";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			qcom,ee = <0>;
-			qcom,channel = <0>;
-			qcom,bus-id = <0>;
+			qup_spi11_data_clk: qup-spi11-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio12", "gpio13", "gpio14";
+				function = "qup2_se3";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			interrupt-controller;
-			#interrupt-cells = <4>;
+			qup_spi12_cs: qup-spi12-cs-state {
+				pins = "gpio19";
+				function = "qup2_se4";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			#address-cells = <2>;
-			#size-cells = <0>;
-		};
+			qup_spi12_data_clk: qup-spi12-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio16", "gpio17", "gpio18";
+				function = "qup2_se4";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-		tlmm: pinctrl@f100000 {
-			compatible = "qcom,sm8650-tlmm";
-			reg = <0 0x0f100000 0 0x300000>;
+			qup_spi13_cs: qup-spi13-cs-state {
+				pins = "gpio23";
+				function = "qup2_se5";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			qup_spi13_data_clk: qup-spi13-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio20", "gpio21", "gpio22";
+				function = "qup2_se5";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			gpio-controller;
-			#gpio-cells = <2>;
+			qup_spi14_cs: qup-spi14-cs-state {
+				pins = "gpio27";
+				function = "qup2_se6";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			interrupt-controller;
-			#interrupt-cells = <2>;
+			qup_spi14_data_clk: qup-spi14-data-clk-state {
+				/* MISO, MOSI, CLK */
+				pins = "gpio24", "gpio25", "gpio26";
+				function = "qup2_se6";
+				drive-strength = <6>;
+				bias-disable;
+			};
 
-			gpio-ranges = <&tlmm 0 0 211>;
+			qup_uart14_default: qup-uart14-default-state {
+				/* TX, RX */
+				pins = "gpio26", "gpio27";
+				function = "qup2_se6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
 
-			wakeup-parent = <&pdc>;
+			qup_uart14_cts_rts: qup-uart14-cts-rts-state {
+				/* CTS, RTS */
+				pins = "gpio24", "gpio25";
+				function = "qup2_se6";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
 
 			qup_uart15_default: qup-uart15-default-state {
 				/* TX, RX */
@@ -1086,6 +3636,46 @@  qup_uart15_default: qup-uart15-default-state {
 				drive-strength = <2>;
 				bias-disable;
 			};
+
+			sdc2_sleep: sdc2-sleep-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			sdc2_default: sdc2-default-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					drive-strength = <16>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
 		};
 
 		apps_smmu: iommu@15000000 {
@@ -1437,6 +4027,105 @@  cpufreq_hw: cpufreq@17d91000 {
 			#clock-cells = <1>;
 		};
 
+		pmu@24091000 {
+			compatible = "qcom,sm8650-llcc-bwmon", "qcom,sc7280-llcc-bwmon";
+			reg = <0 0x24091000 0 0x1000>;
+
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+
+			interconnects = <&mc_virt MASTER_LLCC 3 &mc_virt SLAVE_EBI1 3>;
+
+			operating-points-v2 = <&llcc_bwmon_opp_table>;
+
+			llcc_bwmon_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-0 {
+					opp-peak-kBps = <2086000>;
+				};
+
+				opp-1 {
+					opp-peak-kBps = <2929000>;
+				};
+
+				opp-2 {
+					opp-peak-kBps = <5931000>;
+				};
+
+				opp-3 {
+					opp-peak-kBps = <6515000>;
+				};
+
+				opp-4 {
+					opp-peak-kBps = <7980000>;
+				};
+
+				opp-5 {
+					opp-peak-kBps = <10437000>;
+				};
+
+				opp-6 {
+					opp-peak-kBps = <12157000>;
+				};
+
+				opp-7 {
+					opp-peak-kBps = <14060000>;
+				};
+
+				opp-8 {
+					opp-peak-kBps = <16113000>;
+				};
+			};
+		};
+
+		pmu@240b7400 {
+			compatible = "qcom,sm8650-cpu-bwmon", "qcom,sdm845-bwmon";
+			reg = <0 0x240b7400 0 0x600>;
+
+			interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
+
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &gem_noc SLAVE_LLCC 3>;
+
+			operating-points-v2 = <&cpu_bwmon_opp_table>;
+
+			cpu_bwmon_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-0 {
+					opp-peak-kBps = <4577000>;
+				};
+
+				opp-1 {
+					opp-peak-kBps = <7110000>;
+				};
+
+				opp-2 {
+					opp-peak-kBps = <9155000>;
+				};
+
+				opp-3 {
+					opp-peak-kBps = <12298000>;
+				};
+
+				opp-4 {
+					opp-peak-kBps = <14236000>;
+				};
+
+				opp-5 {
+					opp-peak-kBps = <16265000>;
+				};
+			};
+		};
+
+		gem_noc: interconnect@24100000 {
+			compatible = "qcom,sm8650-gem-noc";
+			reg = <0 0x24100000 0 0xc5080>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
 		system-cache-controller@25000000 {
 			compatible = "qcom,sm8650-llcc";
 			reg = <0 0x25000000 0 0x200000>,
@@ -1452,6 +4141,135 @@  system-cache-controller@25000000 {
 
 			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		remoteproc_adsp: remoteproc@30000000 {
+			compatible = "qcom,sm8650-adsp-pas";
+			reg = <0 0x30000000 0 0x100>;
+
+			interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			interconnects = <&lpass_lpicx_noc MASTER_LPASS_PROC 0 &mc_virt SLAVE_EBI1 0>;
+
+			power-domains = <&rpmhpd RPMHPD_LCX>,
+					<&rpmhpd RPMHPD_LMX>;
+			power-domain-names = "lcx",
+					     "lmx";
+
+			memory-region = <&adspslpi_mem>, <&q6_adsp_dtb_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			remoteproc_adsp_glink: glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+
+				mboxes = <&ipcc IPCC_CLIENT_LPASS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				qcom,remote-pid = <2>;
+
+				label = "lpass";
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+
+					label = "adsp";
+
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
+
+		nsp_noc: interconnect@320c0000 {
+			compatible = "qcom,sm8650-nsp-noc";
+			reg = <0 0x320c0000 0 0xf080>;
+
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			#interconnect-cells = <2>;
+		};
+
+		remoteproc_cdsp: remoteproc@32300000 {
+			compatible = "qcom,sm8650-cdsp-pas";
+			reg = <0 0x32300000 0 0x1400000>;
+
+			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			interconnects = <&nsp_noc MASTER_CDSP_PROC 0 &mc_virt SLAVE_EBI1 0>;
+
+			power-domains = <&rpmhpd RPMHPD_CX>,
+					<&rpmhpd RPMHPD_MXC>,
+					<&rpmhpd RPMHPD_NSP>;
+			power-domain-names = "cx",
+					     "mxc",
+					     "nsp";
+
+			memory-region = <&cdsp_mem>, <&q6_cdsp_dtb_mem>, <&global_sync_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_cdsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+
+				mboxes = <&ipcc IPCC_CLIENT_CDSP
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				qcom,remote-pid = <5>;
+
+				label = "cdsp";
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+
+					label = "cdsp";
+
+					#address-cells = <1>;
+					#size-cells = <0>;
+				};
+			};
+		};
 	};
 
 	thermal-zones {