new file mode 100644
@@ -0,0 +1,179 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (C) 2018 - 2023 Intel Corporation */
+
+#ifndef IPU6_PLATFORM_REGS_H
+#define IPU6_PLATFORM_REGS_H
+
+#include <linux/bits.h>
+
+/*
+ * IPU6 uses uniform address within IPU6, therefore all subsystem registers
+ * locates in one single space starts from 0 but in different sctions with
+ * different addresses, the subsystem offsets are defined to 0 as the
+ * register definition will have the address offset to 0.
+ */
+#define IPU6_UNIFIED_OFFSET 0
+
+#define IPU6_ISYS_IOMMU0_OFFSET 0x2e0000
+#define IPU6_ISYS_IOMMU1_OFFSET 0x2e0500
+#define IPU6_ISYS_IOMMUI_OFFSET 0x2e0a00
+
+#define IPU6_PSYS_IOMMU0_OFFSET 0x1b0000
+#define IPU6_PSYS_IOMMU1_OFFSET 0x1b0700
+#define IPU6_PSYS_IOMMU1R_OFFSET 0x1b0e00
+#define IPU6_PSYS_IOMMUI_OFFSET 0x1b1500
+
+/* the offset from IOMMU base register */
+#define IPU6_MMU_L1_STREAM_ID_REG_OFFSET 0x0c
+#define IPU6_MMU_L2_STREAM_ID_REG_OFFSET 0x4c
+#define IPU6_PSYS_MMU1W_L2_STREAM_ID_REG_OFFSET 0x8c
+
+#define IPU6_MMU_INFO_OFFSET 0x8
+
+#define IPU6_ISYS_SPC_OFFSET 0x210000
+
+#define IPU6SE_PSYS_SPC_OFFSET 0x110000
+#define IPU6_PSYS_SPC_OFFSET 0x118000
+
+#define IPU6_ISYS_DMEM_OFFSET 0x200000
+#define IPU6_PSYS_DMEM_OFFSET 0x100000
+
+#define IPU6_REG_ISYS_UNISPART_IRQ_EDGE 0x27c000
+#define IPU6_REG_ISYS_UNISPART_IRQ_MASK 0x27c004
+#define IPU6_REG_ISYS_UNISPART_IRQ_STATUS 0x27c008
+#define IPU6_REG_ISYS_UNISPART_IRQ_CLEAR 0x27c00c
+#define IPU6_REG_ISYS_UNISPART_IRQ_ENABLE 0x27c010
+#define IPU6_REG_ISYS_UNISPART_IRQ_LEVEL_NOT_PULSE 0x27c014
+#define IPU6_REG_ISYS_UNISPART_SW_IRQ_REG 0x27c414
+#define IPU6_REG_ISYS_UNISPART_SW_IRQ_MUX_REG 0x27c418
+#define IPU6_ISYS_UNISPART_IRQ_CSI0 BIT(2)
+#define IPU6_ISYS_UNISPART_IRQ_CSI1 BIT(3)
+#define IPU6_ISYS_UNISPART_IRQ_SW BIT(22)
+
+#define IPU6_REG_ISYS_ISL_TOP_IRQ_EDGE 0x2b0200
+#define IPU6_REG_ISYS_ISL_TOP_IRQ_MASK 0x2b0204
+#define IPU6_REG_ISYS_ISL_TOP_IRQ_STATUS 0x2b0208
+#define IPU6_REG_ISYS_ISL_TOP_IRQ_CLEAR 0x2b020c
+#define IPU6_REG_ISYS_ISL_TOP_IRQ_ENABLE 0x2b0210
+#define IPU6_REG_ISYS_ISL_TOP_IRQ_LEVEL_NOT_PULSE 0x2b0214
+
+#define IPU6_REG_ISYS_CMPR_TOP_IRQ_EDGE 0x2d2100
+#define IPU6_REG_ISYS_CMPR_TOP_IRQ_MASK 0x2d2104
+#define IPU6_REG_ISYS_CMPR_TOP_IRQ_STATUS 0x2d2108
+#define IPU6_REG_ISYS_CMPR_TOP_IRQ_CLEAR 0x2d210c
+#define IPU6_REG_ISYS_CMPR_TOP_IRQ_ENABLE 0x2d2110
+#define IPU6_REG_ISYS_CMPR_TOP_IRQ_LEVEL_NOT_PULSE 0x2d2114
+
+/* CDC Burst collector thresholds for isys - 3 FIFOs i = 0..2 */
+#define IPU6_REG_ISYS_CDC_THRESHOLD(i) (0x27c400 + ((i) * 4))
+
+#define IPU6_CSI_IRQ_NUM_PER_PIPE 4
+#define IPU6SE_ISYS_CSI_PORT_NUM 4
+#define IPU6_ISYS_CSI_PORT_NUM 8
+
+#define IPU6_ISYS_CSI_PORT_IRQ(irq_num) BIT(irq_num)
+
+/* PKG DIR OFFSET in IMR in secure mode */
+#define IPU6_PKG_DIR_IMR_OFFSET 0x40
+
+#define IPU6_ISYS_REG_SPC_STATUS_CTRL 0x0
+
+#define IPU6_ISYS_SPC_STATUS_START BIT(1)
+#define IPU6_ISYS_SPC_STATUS_RUN BIT(3)
+#define IPU6_ISYS_SPC_STATUS_READY BIT(5)
+#define IPU6_ISYS_SPC_STATUS_CTRL_ICACHE_INVALIDATE BIT(12)
+#define IPU6_ISYS_SPC_STATUS_ICACHE_PREFETCH BIT(13)
+
+#define IPU6_PSYS_REG_SPC_STATUS_CTRL 0x0
+#define IPU6_PSYS_REG_SPC_START_PC 0x4
+#define IPU6_PSYS_REG_SPC_ICACHE_BASE 0x10
+#define IPU6_REG_PSYS_INFO_SEG_0_CONFIG_ICACHE_MASTER 0x14
+
+#define IPU6_PSYS_SPC_STATUS_START BIT(1)
+#define IPU6_PSYS_SPC_STATUS_RUN BIT(3)
+#define IPU6_PSYS_SPC_STATUS_READY BIT(5)
+#define IPU6_PSYS_SPC_STATUS_CTRL_ICACHE_INVALIDATE BIT(12)
+#define IPU6_PSYS_SPC_STATUS_ICACHE_PREFETCH BIT(13)
+
+#define IPU6_PSYS_REG_SPP0_STATUS_CTRL 0x20000
+
+#define IPU6_INFO_ENABLE_SNOOP BIT(0)
+#define IPU6_INFO_DEC_FORCE_FLUSH BIT(1)
+#define IPU6_INFO_DEC_PASS_THROUGH BIT(2)
+#define IPU6_INFO_ZLW BIT(3)
+#define IPU6_INFO_REQUEST_DESTINATION_IOSF BIT(9)
+#define IPU6_INFO_IMR_BASE BIT(10)
+#define IPU6_INFO_IMR_DESTINED BIT(11)
+
+#define IPU6_INFO_REQUEST_DESTINATION_PRIMARY IPU6_INFO_REQUEST_DESTINATION_IOSF
+
+/*
+ * s2m_pixel_soc_pixel_remapping is dedicated for the enabling of the
+ * pixel s2m remp ability.Remap here means that s2m rearange the order
+ * of the pixels in each 4 pixels group.
+ * For examle, mirroring remping means that if input's 4 first pixels
+ * are 1 2 3 4 then in output we should see 4 3 2 1 in this 4 first pixels.
+ * 0xE4 is from s2m MAS document. It means no remapping.
+ */
+#define S2M_PIXEL_SOC_PIXEL_REMAPPING_FLAG_NO_REMAPPING 0xe4
+/*
+ * csi_be_soc_pixel_remapping is for the enabling of the pixel remapping.
+ * This remapping is exactly like the stream2mmio remapping.
+ */
+#define CSI_BE_SOC_PIXEL_REMAPPING_FLAG_NO_REMAPPING 0xe4
+
+#define IPU6_REG_DMA_TOP_AB_GROUP1_BASE_ADDR 0x1ae000
+#define IPU6_REG_DMA_TOP_AB_GROUP2_BASE_ADDR 0x1af000
+#define IPU6_REG_DMA_TOP_AB_RING_MIN_OFFSET(n) (0x4 + (n) * 0xc)
+#define IPU6_REG_DMA_TOP_AB_RING_MAX_OFFSET(n) (0x8 + (n) * 0xc)
+#define IPU6_REG_DMA_TOP_AB_RING_ACCESS_OFFSET(n) (0xc + (n) * 0xc)
+
+enum ipu6_device_ab_group1_target_id {
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R0_SPC_DMEM,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R1_SPC_DMEM,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R2_SPC_DMEM,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R3_SPC_STATUS_REG,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R4_SPC_MASTER_BASE_ADDR,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R5_SPC_PC_STALL,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R6_SPC_EQ,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R7_SPC_RESERVED,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R8_SPC_RESERVED,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R9_SPP0,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R10_SPP1,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R11_CENTRAL_R1,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R12_IRQ,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R13_CENTRAL_R2,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R14_DMA,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R15_DMA,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R16_GP,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R17_ZLW_INSERTER,
+ IPU6_DEVICE_AB_GROUP1_TARGET_ID_R18_AB,
+};
+
+enum nci_ab_access_mode {
+ NCI_AB_ACCESS_MODE_RW, /* read & write */
+ NCI_AB_ACCESS_MODE_RO, /* read only */
+ NCI_AB_ACCESS_MODE_WO, /* write only */
+ NCI_AB_ACCESS_MODE_NA, /* No access at all */
+};
+
+/* IRQ-related registers in PSYS */
+#define IPU6_REG_PSYS_GPDEV_IRQ_EDGE 0x1aa200
+#define IPU6_REG_PSYS_GPDEV_IRQ_MASK 0x1aa204
+#define IPU6_REG_PSYS_GPDEV_IRQ_STATUS 0x1aa208
+#define IPU6_REG_PSYS_GPDEV_IRQ_CLEAR 0x1aa20c
+#define IPU6_REG_PSYS_GPDEV_IRQ_ENABLE 0x1aa210
+#define IPU6_REG_PSYS_GPDEV_IRQ_LEVEL_NOT_PULSE 0x1aa214
+/* There are 8 FW interrupts, n = 0..7 */
+#define IPU6_PSYS_GPDEV_FWIRQ0 5
+#define IPU6_PSYS_GPDEV_FWIRQ1 6
+#define IPU6_PSYS_GPDEV_FWIRQ2 7
+#define IPU6_PSYS_GPDEV_FWIRQ3 8
+#define IPU6_PSYS_GPDEV_FWIRQ4 9
+#define IPU6_PSYS_GPDEV_FWIRQ5 10
+#define IPU6_PSYS_GPDEV_FWIRQ6 11
+#define IPU6_PSYS_GPDEV_FWIRQ7 12
+#define IPU6_PSYS_GPDEV_IRQ_FWIRQ(n) BIT(n)
+#define IPU6_REG_PSYS_GPDEV_FWIRQ(n) (4 * (n) + 0x1aa100)
+
+#endif /* IPU6_PLATFORM_REGS_H */
new file mode 100644
@@ -0,0 +1,952 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2013 - 2023 Intel Corporation
+ */
+
+#include <linux/bitfield.h>
+#include <linux/module.h>
+#include <linux/pci-ats.h>
+#include <linux/pm_runtime.h>
+
+#include <media/ipu-bridge.h>
+
+#include "ipu6.h"
+#include "ipu6-cpd.h"
+#include "ipu6-isys.h"
+#include "ipu6-mmu.h"
+#include "ipu6-platform-buttress-regs.h"
+#include "ipu6-platform-isys-csi2-reg.h"
+#include "ipu6-platform-regs.h"
+
+#define IPU6_PCI_BAR 0
+
+struct ipu6_cell_program {
+ u32 magic_number;
+
+ u32 blob_offset;
+ u32 blob_size;
+
+ u32 start[3];
+
+ u32 icache_source;
+ u32 icache_target;
+ u32 icache_size;
+
+ u32 pmem_source;
+ u32 pmem_target;
+ u32 pmem_size;
+
+ u32 data_source;
+ u32 data_target;
+ u32 data_size;
+
+ u32 bss_target;
+ u32 bss_size;
+
+ u32 cell_id;
+ u32 regs_addr;
+
+ u32 cell_pmem_data_bus_address;
+ u32 cell_dmem_data_bus_address;
+ u32 cell_pmem_control_bus_address;
+ u32 cell_dmem_control_bus_address;
+
+ u32 next;
+ u32 dummy[2];
+};
+
+static u32 ipu6se_csi_offsets[] = {
+ IPU6_CSI_PORT_A_ADDR_OFFSET,
+ IPU6_CSI_PORT_B_ADDR_OFFSET,
+ IPU6_CSI_PORT_C_ADDR_OFFSET,
+ IPU6_CSI_PORT_D_ADDR_OFFSET
+};
+
+/*
+ * IPU6 on TGL support maximum 8 csi2 ports
+ * IPU6SE on JSL and IPU6EP on ADL support maximum 4 csi2 ports
+ * IPU6EP on MTL support maximum 6 csi2 ports
+ */
+static u32 ipu6_tgl_csi_offsets[] = {
+ IPU6_CSI_PORT_A_ADDR_OFFSET,
+ IPU6_CSI_PORT_B_ADDR_OFFSET,
+ IPU6_CSI_PORT_C_ADDR_OFFSET,
+ IPU6_CSI_PORT_D_ADDR_OFFSET,
+ IPU6_CSI_PORT_E_ADDR_OFFSET,
+ IPU6_CSI_PORT_F_ADDR_OFFSET,
+ IPU6_CSI_PORT_G_ADDR_OFFSET,
+ IPU6_CSI_PORT_H_ADDR_OFFSET
+};
+
+static u32 ipu6ep_mtl_csi_offsets[] = {
+ IPU6_CSI_PORT_A_ADDR_OFFSET,
+ IPU6_CSI_PORT_B_ADDR_OFFSET,
+ IPU6_CSI_PORT_C_ADDR_OFFSET,
+ IPU6_CSI_PORT_D_ADDR_OFFSET,
+ IPU6_CSI_PORT_E_ADDR_OFFSET,
+ IPU6_CSI_PORT_F_ADDR_OFFSET
+};
+
+static u32 ipu6_csi_offsets[] = {
+ IPU6_CSI_PORT_A_ADDR_OFFSET,
+ IPU6_CSI_PORT_B_ADDR_OFFSET,
+ IPU6_CSI_PORT_C_ADDR_OFFSET,
+ IPU6_CSI_PORT_D_ADDR_OFFSET
+};
+
+static struct ipu6_isys_internal_pdata isys_ipdata = {
+ .hw_variant = {
+ .offset = IPU6_UNIFIED_OFFSET,
+ .nr_mmus = 3,
+ .mmu_hw = {
+ {
+ .offset = IPU6_ISYS_IOMMU0_OFFSET,
+ .info_bits = IPU6_INFO_REQUEST_DESTINATION_IOSF,
+ .nr_l1streams = 16,
+ .l1_block_sz = {
+ 3, 8, 2, 2, 2, 2, 2, 2, 1, 1,
+ 1, 1, 1, 1, 1, 1
+ },
+ .nr_l2streams = 16,
+ .l2_block_sz = {
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 2
+ },
+ .insert_read_before_invalidate = false,
+ .l1_stream_id_reg_offset =
+ IPU6_MMU_L1_STREAM_ID_REG_OFFSET,
+ .l2_stream_id_reg_offset =
+ IPU6_MMU_L2_STREAM_ID_REG_OFFSET,
+ },
+ {
+ .offset = IPU6_ISYS_IOMMU1_OFFSET,
+ .info_bits = 0,
+ .nr_l1streams = 16,
+ .l1_block_sz = {
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 1, 1, 4
+ },
+ .nr_l2streams = 16,
+ .l2_block_sz = {
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 2
+ },
+ .insert_read_before_invalidate = false,
+ .l1_stream_id_reg_offset =
+ IPU6_MMU_L1_STREAM_ID_REG_OFFSET,
+ .l2_stream_id_reg_offset =
+ IPU6_MMU_L2_STREAM_ID_REG_OFFSET,
+ },
+ {
+ .offset = IPU6_ISYS_IOMMUI_OFFSET,
+ .info_bits = 0,
+ .nr_l1streams = 0,
+ .nr_l2streams = 0,
+ .insert_read_before_invalidate = false,
+ },
+ },
+ .cdc_fifos = 3,
+ .cdc_fifo_threshold = {6, 8, 2},
+ .dmem_offset = IPU6_ISYS_DMEM_OFFSET,
+ .spc_offset = IPU6_ISYS_SPC_OFFSET,
+ },
+ .isys_dma_overshoot = IPU6_ISYS_OVERALLOC_MIN,
+};
+
+static struct ipu6_psys_internal_pdata psys_ipdata = {
+ .hw_variant = {
+ .offset = IPU6_UNIFIED_OFFSET,
+ .nr_mmus = 4,
+ .mmu_hw = {
+ {
+ .offset = IPU6_PSYS_IOMMU0_OFFSET,
+ .info_bits =
+ IPU6_INFO_REQUEST_DESTINATION_IOSF,
+ .nr_l1streams = 16,
+ .l1_block_sz = {
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 2
+ },
+ .nr_l2streams = 16,
+ .l2_block_sz = {
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 2
+ },
+ .insert_read_before_invalidate = false,
+ .l1_stream_id_reg_offset =
+ IPU6_MMU_L1_STREAM_ID_REG_OFFSET,
+ .l2_stream_id_reg_offset =
+ IPU6_MMU_L2_STREAM_ID_REG_OFFSET,
+ },
+ {
+ .offset = IPU6_PSYS_IOMMU1_OFFSET,
+ .info_bits = 0,
+ .nr_l1streams = 32,
+ .l1_block_sz = {
+ 1, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 10,
+ 5, 4, 14, 6, 4, 14, 6, 4, 8,
+ 4, 2, 1, 1, 1, 1, 14
+ },
+ .nr_l2streams = 32,
+ .l2_block_sz = {
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 2
+ },
+ .insert_read_before_invalidate = false,
+ .l1_stream_id_reg_offset =
+ IPU6_MMU_L1_STREAM_ID_REG_OFFSET,
+ .l2_stream_id_reg_offset =
+ IPU6_PSYS_MMU1W_L2_STREAM_ID_REG_OFFSET,
+ },
+ {
+ .offset = IPU6_PSYS_IOMMU1R_OFFSET,
+ .info_bits = 0,
+ .nr_l1streams = 16,
+ .l1_block_sz = {
+ 1, 4, 4, 4, 4, 16, 8, 4, 32,
+ 16, 16, 2, 2, 2, 1, 12
+ },
+ .nr_l2streams = 16,
+ .l2_block_sz = {
+ 2, 2, 2, 2, 2, 2, 2, 2, 2, 2,
+ 2, 2, 2, 2, 2, 2
+ },
+ .insert_read_before_invalidate = false,
+ .l1_stream_id_reg_offset =
+ IPU6_MMU_L1_STREAM_ID_REG_OFFSET,
+ .l2_stream_id_reg_offset =
+ IPU6_MMU_L2_STREAM_ID_REG_OFFSET,
+ },
+ {
+ .offset = IPU6_PSYS_IOMMUI_OFFSET,
+ .info_bits = 0,
+ .nr_l1streams = 0,
+ .nr_l2streams = 0,
+ .insert_read_before_invalidate = false,
+ },
+ },
+ .dmem_offset = IPU6_PSYS_DMEM_OFFSET,
+ },
+};
+
+static const struct ipu6_buttress_ctrl isys_buttress_ctrl = {
+ .ratio = IPU6_IS_FREQ_CTL_DEFAULT_RATIO,
+ .qos_floor = IPU6_IS_FREQ_CTL_DEFAULT_QOS_FLOOR_RATIO,
+ .freq_ctl = IPU6_BUTTRESS_REG_IS_FREQ_CTL,
+ .pwr_sts_shift = IPU6_BUTTRESS_PWR_STATE_IS_PWR_SHIFT,
+ .pwr_sts_mask = IPU6_BUTTRESS_PWR_STATE_IS_PWR_MASK,
+ .pwr_sts_on = IPU6_BUTTRESS_PWR_STATE_UP_DONE,
+ .pwr_sts_off = IPU6_BUTTRESS_PWR_STATE_DN_DONE,
+};
+
+static const struct ipu6_buttress_ctrl psys_buttress_ctrl = {
+ .ratio = IPU6_PS_FREQ_CTL_DEFAULT_RATIO,
+ .qos_floor = IPU6_PS_FREQ_CTL_DEFAULT_QOS_FLOOR_RATIO,
+ .freq_ctl = IPU6_BUTTRESS_REG_PS_FREQ_CTL,
+ .pwr_sts_shift = IPU6_BUTTRESS_PWR_STATE_PS_PWR_SHIFT,
+ .pwr_sts_mask = IPU6_BUTTRESS_PWR_STATE_PS_PWR_MASK,
+ .pwr_sts_on = IPU6_BUTTRESS_PWR_STATE_UP_DONE,
+ .pwr_sts_off = IPU6_BUTTRESS_PWR_STATE_DN_DONE,
+};
+
+static void
+ipu6_pkg_dir_configure_spc(struct ipu6_device *isp,
+ const struct ipu6_hw_variants *hw_variant,
+ int pkg_dir_idx, void __iomem *base,
+ u64 *pkg_dir, dma_addr_t pkg_dir_vied_address)
+{
+ struct ipu6_cell_program *prog;
+ void __iomem *spc_base;
+ u32 server_fw_addr;
+ dma_addr_t dma_addr;
+ u32 pg_offset;
+
+ server_fw_addr = lower_32_bits(*(pkg_dir + (pkg_dir_idx + 1) * 2));
+ if (pkg_dir_idx == IPU6_CPD_PKG_DIR_ISYS_SERVER_IDX)
+ dma_addr = sg_dma_address(isp->isys->fw_sgt.sgl);
+ else
+ dma_addr = sg_dma_address(isp->psys->fw_sgt.sgl);
+
+ pg_offset = server_fw_addr - dma_addr;
+ prog = (struct ipu6_cell_program *)((u64)isp->cpd_fw->data + pg_offset);
+ spc_base = base + prog->regs_addr;
+ if (spc_base != (base + hw_variant->spc_offset))
+ dev_warn(&isp->pdev->dev,
+ "SPC reg addr %p not matching value from CPD %p\n",
+ base + hw_variant->spc_offset, spc_base);
+ writel(server_fw_addr + prog->blob_offset +
+ prog->icache_source, spc_base + IPU6_PSYS_REG_SPC_ICACHE_BASE);
+ writel(IPU6_INFO_REQUEST_DESTINATION_IOSF,
+ spc_base + IPU6_REG_PSYS_INFO_SEG_0_CONFIG_ICACHE_MASTER);
+ writel(prog->start[1], spc_base + IPU6_PSYS_REG_SPC_START_PC);
+ writel(pkg_dir_vied_address, base + hw_variant->dmem_offset);
+}
+
+void ipu6_configure_spc(struct ipu6_device *isp,
+ const struct ipu6_hw_variants *hw_variant,
+ int pkg_dir_idx, void __iomem *base, u64 *pkg_dir,
+ dma_addr_t pkg_dir_dma_addr)
+{
+ void __iomem *dmem_base = base + hw_variant->dmem_offset;
+ void __iomem *spc_regs_base = base + hw_variant->spc_offset;
+ u32 val;
+
+ val = readl(spc_regs_base + IPU6_PSYS_REG_SPC_STATUS_CTRL);
+ val |= IPU6_PSYS_SPC_STATUS_CTRL_ICACHE_INVALIDATE;
+ writel(val, spc_regs_base + IPU6_PSYS_REG_SPC_STATUS_CTRL);
+
+ if (isp->secure_mode)
+ writel(IPU6_PKG_DIR_IMR_OFFSET, dmem_base);
+ else
+ ipu6_pkg_dir_configure_spc(isp, hw_variant, pkg_dir_idx, base,
+ pkg_dir, pkg_dir_dma_addr);
+}
+EXPORT_SYMBOL_NS_GPL(ipu6_configure_spc, INTEL_IPU6);
+
+static void ipu6_internal_pdata_init(struct ipu6_device *isp)
+{
+ u8 hw_ver = isp->hw_ver;
+
+ isys_ipdata.num_parallel_streams = IPU6_ISYS_NUM_STREAMS;
+ isys_ipdata.sram_gran_shift = IPU6_SRAM_GRANULARITY_SHIFT;
+ isys_ipdata.sram_gran_size = IPU6_SRAM_GRANULARITY_SIZE;
+ isys_ipdata.max_sram_size = IPU6_MAX_SRAM_SIZE;
+ isys_ipdata.sensor_type_start = IPU6_FW_ISYS_SENSOR_TYPE_START;
+ isys_ipdata.sensor_type_end = IPU6_FW_ISYS_SENSOR_TYPE_END;
+ isys_ipdata.max_streams = IPU6_ISYS_NUM_STREAMS;
+ isys_ipdata.max_send_queues = IPU6_N_MAX_SEND_QUEUES;
+ isys_ipdata.max_sram_blocks = IPU6_NOF_SRAM_BLOCKS_MAX;
+ isys_ipdata.max_devq_size = IPU6_DEV_SEND_QUEUE_SIZE;
+ isys_ipdata.csi2.nports = ARRAY_SIZE(ipu6_csi_offsets);
+ isys_ipdata.csi2.offsets = ipu6_csi_offsets;
+ isys_ipdata.csi2.irq_mask = IPU6_CSI_RX_ERROR_IRQ_MASK;
+ isys_ipdata.csi2.ctrl0_irq_edge = IPU6_REG_ISYS_CSI_TOP_CTRL0_IRQ_EDGE;
+ isys_ipdata.csi2.ctrl0_irq_clear =
+ IPU6_REG_ISYS_CSI_TOP_CTRL0_IRQ_CLEAR;
+ isys_ipdata.csi2.ctrl0_irq_mask = IPU6_REG_ISYS_CSI_TOP_CTRL0_IRQ_MASK;
+ isys_ipdata.csi2.ctrl0_irq_enable =
+ IPU6_REG_ISYS_CSI_TOP_CTRL0_IRQ_ENABLE;
+ isys_ipdata.csi2.ctrl0_irq_status =
+ IPU6_REG_ISYS_CSI_TOP_CTRL0_IRQ_STATUS;
+ isys_ipdata.csi2.ctrl0_irq_lnp =
+ IPU6_REG_ISYS_CSI_TOP_CTRL0_IRQ_LEVEL_NOT_PULSE;
+ isys_ipdata.enhanced_iwake = is_ipu6ep_mtl(hw_ver) || is_ipu6ep(hw_ver);
+ psys_ipdata.hw_variant.spc_offset = IPU6_PSYS_SPC_OFFSET;
+ isys_ipdata.csi2.fw_access_port_ofs = CSI_REG_HUB_FW_ACCESS_PORT_OFS;
+
+ if (is_ipu6ep(hw_ver)) {
+ isys_ipdata.ltr = IPU6EP_LTR_VALUE;
+ isys_ipdata.memopen_threshold = IPU6EP_MIN_MEMOPEN_TH;
+ }
+
+ if (is_ipu6_tgl(hw_ver)) {
+ isys_ipdata.csi2.nports = ARRAY_SIZE(ipu6_tgl_csi_offsets);
+ isys_ipdata.csi2.offsets = ipu6_tgl_csi_offsets;
+ }
+
+ if (is_ipu6ep_mtl(hw_ver)) {
+ isys_ipdata.csi2.nports = ARRAY_SIZE(ipu6ep_mtl_csi_offsets);
+ isys_ipdata.csi2.offsets = ipu6ep_mtl_csi_offsets;
+
+ isys_ipdata.csi2.ctrl0_irq_edge =
+ IPU6V6_REG_ISYS_CSI_TOP_CTRL0_IRQ_EDGE;
+ isys_ipdata.csi2.ctrl0_irq_clear =
+ IPU6V6_REG_ISYS_CSI_TOP_CTRL0_IRQ_CLEAR;
+ isys_ipdata.csi2.ctrl0_irq_mask =
+ IPU6V6_REG_ISYS_CSI_TOP_CTRL0_IRQ_MASK;
+ isys_ipdata.csi2.ctrl0_irq_enable =
+ IPU6V6_REG_ISYS_CSI_TOP_CTRL0_IRQ_ENABLE;
+ isys_ipdata.csi2.ctrl0_irq_lnp =
+ IPU6V6_REG_ISYS_CSI_TOP_CTRL0_IRQ_LEVEL_NOT_PULSE;
+ isys_ipdata.csi2.ctrl0_irq_status =
+ IPU6V6_REG_ISYS_CSI_TOP_CTRL0_IRQ_STATUS;
+ isys_ipdata.csi2.fw_access_port_ofs =
+ CSI_REG_HUB_FW_ACCESS_PORT_V6OFS;
+ isys_ipdata.ltr = IPU6EP_MTL_LTR_VALUE;
+ isys_ipdata.memopen_threshold = IPU6EP_MTL_MIN_MEMOPEN_TH;
+ }
+
+ if (is_ipu6se(hw_ver)) {
+ isys_ipdata.csi2.nports = ARRAY_SIZE(ipu6se_csi_offsets);
+ isys_ipdata.csi2.irq_mask = IPU6SE_CSI_RX_ERROR_IRQ_MASK;
+ isys_ipdata.csi2.offsets = ipu6se_csi_offsets;
+ isys_ipdata.num_parallel_streams = IPU6SE_ISYS_NUM_STREAMS;
+ isys_ipdata.sram_gran_shift = IPU6SE_SRAM_GRANULARITY_SHIFT;
+ isys_ipdata.sram_gran_size = IPU6SE_SRAM_GRANULARITY_SIZE;
+ isys_ipdata.max_sram_size = IPU6SE_MAX_SRAM_SIZE;
+ isys_ipdata.sensor_type_start =
+ IPU6SE_FW_ISYS_SENSOR_TYPE_START;
+ isys_ipdata.sensor_type_end = IPU6SE_FW_ISYS_SENSOR_TYPE_END;
+ isys_ipdata.max_streams = IPU6SE_ISYS_NUM_STREAMS;
+ isys_ipdata.max_send_queues = IPU6SE_N_MAX_SEND_QUEUES;
+ isys_ipdata.max_sram_blocks = IPU6SE_NOF_SRAM_BLOCKS_MAX;
+ isys_ipdata.max_devq_size = IPU6SE_DEV_SEND_QUEUE_SIZE;
+ psys_ipdata.hw_variant.spc_offset = IPU6SE_PSYS_SPC_OFFSET;
+ }
+}
+
+static int ipu6_isys_check_fwnode_graph(struct fwnode_handle *fwnode)
+{
+ struct fwnode_handle *endpoint;
+
+ if (IS_ERR_OR_NULL(fwnode))
+ return -EINVAL;
+
+ endpoint = fwnode_graph_get_next_endpoint(fwnode, NULL);
+ if (endpoint) {
+ fwnode_handle_put(endpoint);
+ return 0;
+ }
+
+ return ipu6_isys_check_fwnode_graph(fwnode->secondary);
+}
+
+static struct ipu6_bus_device *
+ipu6_isys_init(struct pci_dev *pdev, struct device *parent,
+ struct ipu6_buttress_ctrl *ctrl, void __iomem *base,
+ const struct ipu6_isys_internal_pdata *ipdata)
+{
+ struct fwnode_handle *fwnode = dev_fwnode(&pdev->dev);
+ struct ipu6_bus_device *isys_adev;
+ struct ipu6_isys_pdata *pdata;
+ int ret;
+
+ /* check fwnode at first, fallback into bridge if no fwnode graph */
+ ret = ipu6_isys_check_fwnode_graph(fwnode);
+ if (ret) {
+ if (fwnode && !IS_ERR_OR_NULL(fwnode->secondary)) {
+ dev_err(&pdev->dev,
+ "fwnode graph has no endpoints connection\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ ret = ipu_bridge_init(&pdev->dev, ipu_bridge_parse_ssdb);
+ if (ret) {
+ if (ret != -EPROBE_DEFER)
+ dev_err_probe(&pdev->dev, ret,
+ "IPU6 bridge init failed\n");
+ return ERR_PTR(ret);
+ }
+ }
+
+ pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return ERR_PTR(-ENOMEM);
+
+ pdata->base = base;
+ pdata->ipdata = ipdata;
+
+ isys_adev = ipu6_bus_initialize_device(pdev, parent, pdata, ctrl,
+ IPU6_ISYS_NAME);
+ if (IS_ERR(isys_adev)) {
+ dev_err_probe(&pdev->dev, PTR_ERR(isys_adev),
+ "ipu6_bus_initialize_device isys failed\n");
+ kfree(pdata);
+ return ERR_CAST(isys_adev);
+ }
+
+ isys_adev->mmu = ipu6_mmu_init(&pdev->dev, base, ISYS_MMID,
+ &ipdata->hw_variant);
+ if (IS_ERR(isys_adev->mmu)) {
+ dev_err_probe(&pdev->dev, PTR_ERR(isys_adev),
+ "ipu6_mmu_init(isys_adev->mmu) failed\n");
+ put_device(&isys_adev->auxdev.dev);
+ kfree(pdata);
+ return ERR_CAST(isys_adev->mmu);
+ }
+
+ isys_adev->mmu->dev = &isys_adev->auxdev.dev;
+
+ ret = ipu6_bus_add_device(isys_adev);
+ if (ret) {
+ kfree(pdata);
+ return ERR_PTR(ret);
+ }
+
+ return isys_adev;
+}
+
+static struct ipu6_bus_device *
+ipu6_psys_init(struct pci_dev *pdev, struct device *parent,
+ struct ipu6_buttress_ctrl *ctrl, void __iomem *base,
+ const struct ipu6_psys_internal_pdata *ipdata)
+{
+ struct ipu6_bus_device *psys_adev;
+ struct ipu6_psys_pdata *pdata;
+ int ret;
+
+ pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return ERR_PTR(-ENOMEM);
+
+ pdata->base = base;
+ pdata->ipdata = ipdata;
+
+ psys_adev = ipu6_bus_initialize_device(pdev, parent, pdata, ctrl,
+ IPU6_PSYS_NAME);
+ if (IS_ERR(psys_adev)) {
+ dev_err_probe(&pdev->dev, PTR_ERR(psys_adev),
+ "ipu6_bus_initialize_device psys failed\n");
+ kfree(pdata);
+ return ERR_CAST(psys_adev);
+ }
+
+ psys_adev->mmu = ipu6_mmu_init(&pdev->dev, base, PSYS_MMID,
+ &ipdata->hw_variant);
+ if (IS_ERR(psys_adev->mmu)) {
+ dev_err_probe(&pdev->dev, PTR_ERR(psys_adev),
+ "ipu6_mmu_init(psys_adev->mmu) failed\n");
+ put_device(&psys_adev->auxdev.dev);
+ kfree(pdata);
+ return ERR_CAST(psys_adev->mmu);
+ }
+
+ psys_adev->mmu->dev = &psys_adev->auxdev.dev;
+
+ ret = ipu6_bus_add_device(psys_adev);
+ if (ret) {
+ kfree(pdata);
+ return ERR_PTR(ret);
+ }
+
+ return psys_adev;
+}
+
+static int ipu6_pci_config_setup(struct pci_dev *dev, u8 hw_ver)
+{
+ int ret;
+
+ /* disable IPU6 PCI ATS on mtl ES2 */
+ if (is_ipu6ep_mtl(hw_ver) && boot_cpu_data.x86_stepping == 0x2 &&
+ pci_ats_supported(dev))
+ pci_disable_ats(dev);
+
+ /* No PCI msi capability for IPU6EP */
+ if (is_ipu6ep(hw_ver) || is_ipu6ep_mtl(hw_ver)) {
+ /* likely do nothing as msi not enabled by default */
+ pci_disable_msi(dev);
+ return 0;
+ }
+
+ ret = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_MSI);
+ if (ret)
+ dev_err_probe(&dev->dev, ret, "Request msi failed");
+
+ return ret;
+}
+
+static void ipu6_configure_vc_mechanism(struct ipu6_device *isp)
+{
+ u32 val = readl(isp->base + BUTTRESS_REG_BTRS_CTRL);
+
+ if (IPU6_BTRS_ARB_STALL_MODE_VC0 == IPU6_BTRS_ARB_MODE_TYPE_STALL)
+ val |= BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC0;
+ else
+ val &= ~BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC0;
+
+ if (IPU6_BTRS_ARB_STALL_MODE_VC1 == IPU6_BTRS_ARB_MODE_TYPE_STALL)
+ val |= BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC1;
+ else
+ val &= ~BUTTRESS_REG_BTRS_CTRL_STALL_MODE_VC1;
+
+ writel(val, isp->base + BUTTRESS_REG_BTRS_CTRL);
+}
+
+static int request_cpd_fw(const struct firmware **firmware_p, const char *name,
+ struct device *device)
+{
+ const struct firmware *fw;
+ struct firmware *dst;
+ int ret = 0;
+
+ ret = request_firmware(&fw, name, device);
+ if (ret)
+ return ret;
+
+ if (is_vmalloc_addr(fw->data)) {
+ *firmware_p = fw;
+ return 0;
+ }
+
+ dst = kzalloc(sizeof(*dst), GFP_KERNEL);
+ if (!dst) {
+ ret = -ENOMEM;
+ goto release_firmware;
+ }
+
+ dst->size = fw->size;
+ dst->data = vmalloc(fw->size);
+ if (!dst->data) {
+ kfree(dst);
+ ret = -ENOMEM;
+ goto release_firmware;
+ }
+
+ memcpy((void *)dst->data, fw->data, fw->size);
+ *firmware_p = dst;
+
+release_firmware:
+ release_firmware(fw);
+
+ return ret;
+}
+
+static int ipu6_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+ struct ipu6_buttress_ctrl *isys_ctrl = NULL, *psys_ctrl = NULL;
+ void __iomem *isys_base = NULL;
+ void __iomem *psys_base = NULL;
+ struct ipu6_device *isp;
+ phys_addr_t phys;
+ u32 val, version, sku_id;
+ int ret;
+
+ isp = devm_kzalloc(&pdev->dev, sizeof(*isp), GFP_KERNEL);
+ if (!isp)
+ return -ENOMEM;
+
+ isp->pdev = pdev;
+ INIT_LIST_HEAD(&isp->devices);
+
+ ret = pcim_enable_device(pdev);
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret,
+ "Enable PCI device failed\n");
+
+ phys = pci_resource_start(pdev, IPU6_PCI_BAR);
+ dev_dbg(&pdev->dev, "IPU6 PCI bar[%u] = %pa\n", IPU6_PCI_BAR, &phys);
+
+ ret = pcim_iomap_regions(pdev, 1 << IPU6_PCI_BAR, pci_name(pdev));
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret,
+ "Failed to I/O mem remappinp\n");
+
+ isp->base = pcim_iomap_table(pdev)[IPU6_PCI_BAR];
+ pci_set_drvdata(pdev, isp);
+ pci_set_master(pdev);
+
+ isp->cpd_metadata_cmpnt_size = sizeof(struct ipu6_cpd_metadata_cmpnt);
+ switch (id->device) {
+ case PCI_DEVICE_ID_INTEL_IPU6:
+ isp->hw_ver = IPU6_VER_6;
+ isp->cpd_fw_name = IPU6_FIRMWARE_NAME;
+ break;
+ case PCI_DEVICE_ID_INTEL_IPU6SE:
+ isp->hw_ver = IPU6_VER_6SE;
+ isp->cpd_fw_name = IPU6SE_FIRMWARE_NAME;
+ isp->cpd_metadata_cmpnt_size =
+ sizeof(struct ipu6se_cpd_metadata_cmpnt);
+ break;
+ case PCI_DEVICE_ID_INTEL_IPU6EP_ADLP:
+ case PCI_DEVICE_ID_INTEL_IPU6EP_ADLN:
+ case PCI_DEVICE_ID_INTEL_IPU6EP_RPLP:
+ isp->hw_ver = IPU6_VER_6EP;
+ isp->cpd_fw_name = IPU6EP_FIRMWARE_NAME;
+ break;
+ case PCI_DEVICE_ID_INTEL_IPU6EP_MTL:
+ isp->hw_ver = IPU6_VER_6EP_MTL;
+ isp->cpd_fw_name = IPU6EPMTL_FIRMWARE_NAME;
+ break;
+ default:
+ return dev_err_probe(&pdev->dev, -ENODEV,
+ "Unsupported IPU6 device %x\n",
+ id->device);
+ }
+
+ ipu6_internal_pdata_init(isp);
+
+ isys_base = isp->base + isys_ipdata.hw_variant.offset;
+ psys_base = isp->base + psys_ipdata.hw_variant.offset;
+
+ ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(39));
+ if (ret)
+ return dev_err_probe(&pdev->dev, ret,
+ "Failed to set DMA mask\n");
+
+ dma_set_max_seg_size(&pdev->dev, UINT_MAX);
+
+ ret = ipu6_pci_config_setup(pdev, isp->hw_ver);
+ if (ret)
+ return ret;
+
+ ret = ipu6_buttress_init(isp);
+ if (ret)
+ return ret;
+
+ ret = request_cpd_fw(&isp->cpd_fw, isp->cpd_fw_name, &pdev->dev);
+ if (ret) {
+ dev_err_probe(&isp->pdev->dev, ret,
+ "Requesting signed firmware %s failed\n",
+ isp->cpd_fw_name);
+ goto buttress_exit;
+ }
+
+ ret = ipu6_cpd_validate_cpd_file(isp, isp->cpd_fw->data,
+ isp->cpd_fw->size);
+ if (ret) {
+ dev_err_probe(&isp->pdev->dev, ret,
+ "Failed to validate cpd\n");
+ goto out_ipu6_bus_del_devices;
+ }
+
+ isys_ctrl = devm_kmemdup(&pdev->dev, &isys_buttress_ctrl,
+ sizeof(isys_buttress_ctrl), GFP_KERNEL);
+ if (!isys_ctrl) {
+ ret = -ENOMEM;
+ goto out_ipu6_bus_del_devices;
+ }
+
+ isp->isys = ipu6_isys_init(pdev, &pdev->dev, isys_ctrl, isys_base,
+ &isys_ipdata);
+ if (IS_ERR(isp->isys)) {
+ ret = PTR_ERR(isp->isys);
+ goto out_ipu6_bus_del_devices;
+ }
+
+ psys_ctrl = devm_kmemdup(&pdev->dev, &psys_buttress_ctrl,
+ sizeof(psys_buttress_ctrl), GFP_KERNEL);
+ if (!psys_ctrl) {
+ ret = -ENOMEM;
+ goto out_ipu6_bus_del_devices;
+ }
+
+ isp->psys = ipu6_psys_init(pdev, &isp->isys->auxdev.dev, psys_ctrl,
+ psys_base, &psys_ipdata);
+ if (IS_ERR(isp->psys)) {
+ ret = PTR_ERR(isp->psys);
+ goto out_ipu6_bus_del_devices;
+ }
+
+ ret = pm_runtime_resume_and_get(&isp->psys->auxdev.dev);
+ if (ret < 0)
+ goto out_ipu6_bus_del_devices;
+
+ ret = ipu6_mmu_hw_init(isp->psys->mmu);
+ if (ret) {
+ dev_err_probe(&isp->pdev->dev, ret,
+ "Failed to set MMU hardware\n");
+ goto out_ipu6_bus_del_devices;
+ }
+
+ ret = ipu6_buttress_map_fw_image(isp->psys, isp->cpd_fw,
+ &isp->psys->fw_sgt);
+ if (ret) {
+ dev_err_probe(&isp->pdev->dev, ret, "failed to map fw image\n");
+ goto out_ipu6_bus_del_devices;
+ }
+
+ ret = ipu6_cpd_create_pkg_dir(isp->psys, isp->cpd_fw->data);
+ if (ret) {
+ dev_err_probe(&isp->pdev->dev, ret,
+ "failed to create pkg dir\n");
+ goto out_ipu6_bus_del_devices;
+ }
+
+ ret = devm_request_threaded_irq(&pdev->dev, pdev->irq,
+ ipu6_buttress_isr,
+ ipu6_buttress_isr_threaded,
+ IRQF_SHARED, IPU6_NAME, isp);
+ if (ret) {
+ dev_err_probe(&pdev->dev, ret, "Requesting irq failed\n");
+ goto out_ipu6_bus_del_devices;
+ }
+
+ ret = ipu6_buttress_authenticate(isp);
+ if (ret) {
+ dev_err_probe(&isp->pdev->dev, ret,
+ "FW authentication failed\n");
+ goto out_ipu6_bus_del_devices;
+ }
+
+ ipu6_mmu_hw_cleanup(isp->psys->mmu);
+ pm_runtime_put(&isp->psys->auxdev.dev);
+
+ /* Configure the arbitration mechanisms for VC requests */
+ ipu6_configure_vc_mechanism(isp);
+
+ val = readl(isp->base + BUTTRESS_REG_SKU);
+ sku_id = FIELD_GET(GENMASK(6, 4), val);
+ version = FIELD_GET(GENMASK(3, 0), val);
+ dev_info(&pdev->dev, "IPU%u-v%u[%x] hardware version %d\n",
+ version, sku_id, pdev->device, isp->hw_ver);
+
+ pm_runtime_put_noidle(&pdev->dev);
+ pm_runtime_allow(&pdev->dev);
+
+ isp->bus_ready_to_probe = true;
+
+ return 0;
+
+out_ipu6_bus_del_devices:
+ if (isp->psys) {
+ ipu6_cpd_free_pkg_dir(isp->psys);
+ ipu6_buttress_unmap_fw_image(isp->psys, &isp->psys->fw_sgt);
+ }
+ if (!IS_ERR_OR_NULL(isp->psys) && !IS_ERR_OR_NULL(isp->psys->mmu))
+ ipu6_mmu_cleanup(isp->psys->mmu);
+ if (!IS_ERR_OR_NULL(isp->isys) && !IS_ERR_OR_NULL(isp->isys->mmu))
+ ipu6_mmu_cleanup(isp->isys->mmu);
+ ipu6_bus_del_devices(pdev);
+ release_firmware(isp->cpd_fw);
+buttress_exit:
+ ipu6_buttress_exit(isp);
+
+ return ret;
+}
+
+static void ipu6_pci_remove(struct pci_dev *pdev)
+{
+ struct ipu6_device *isp = pci_get_drvdata(pdev);
+ struct ipu6_mmu *isys_mmu = isp->isys->mmu;
+ struct ipu6_mmu *psys_mmu = isp->psys->mmu;
+
+ ipu6_cpd_free_pkg_dir(isp->psys);
+
+ ipu6_buttress_unmap_fw_image(isp->psys, &isp->psys->fw_sgt);
+
+ ipu6_bus_del_devices(pdev);
+
+ pm_runtime_forbid(&pdev->dev);
+ pm_runtime_get_noresume(&pdev->dev);
+
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+
+ ipu6_buttress_exit(isp);
+
+ release_firmware(isp->cpd_fw);
+
+ ipu6_mmu_cleanup(psys_mmu);
+ ipu6_mmu_cleanup(isys_mmu);
+}
+
+static void ipu6_pci_reset_prepare(struct pci_dev *pdev)
+{
+ struct ipu6_device *isp = pci_get_drvdata(pdev);
+
+ pm_runtime_forbid(&isp->pdev->dev);
+}
+
+static void ipu6_pci_reset_done(struct pci_dev *pdev)
+{
+ struct ipu6_device *isp = pci_get_drvdata(pdev);
+
+ ipu6_buttress_restore(isp);
+ if (isp->secure_mode)
+ ipu6_buttress_reset_authentication(isp);
+
+ isp->need_ipc_reset = true;
+ pm_runtime_allow(&isp->pdev->dev);
+}
+
+/*
+ * PCI base driver code requires driver to provide these to enable
+ * PCI device level PM state transitions (D0<->D3)
+ */
+static int ipu6_suspend(struct device *dev)
+{
+ return 0;
+}
+
+static int ipu6_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct ipu6_device *isp = pci_get_drvdata(pdev);
+ struct ipu6_buttress *b = &isp->buttress;
+ int ret;
+
+ /* Configure the arbitration mechanisms for VC requests */
+ ipu6_configure_vc_mechanism(isp);
+
+ isp->secure_mode = ipu6_buttress_get_secure_mode(isp);
+ dev_info(dev, "IPU6 in %s mode\n",
+ isp->secure_mode ? "secure" : "non-secure");
+
+ ipu6_buttress_restore(isp);
+
+ ret = ipu6_buttress_ipc_reset(isp, &b->cse);
+ if (ret)
+ dev_err(&isp->pdev->dev, "IPC reset protocol failed!\n");
+
+ ret = pm_runtime_resume_and_get(&isp->psys->auxdev.dev);
+ if (ret < 0) {
+ dev_err(&isp->psys->auxdev.dev, "Failed to get runtime PM\n");
+ return 0;
+ }
+
+ ret = ipu6_buttress_authenticate(isp);
+ if (ret)
+ dev_err(&isp->pdev->dev, "FW authentication failed(%d)\n", ret);
+
+ pm_runtime_put(&isp->psys->auxdev.dev);
+
+ return 0;
+}
+
+static int ipu6_runtime_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct ipu6_device *isp = pci_get_drvdata(pdev);
+ int ret;
+
+ ipu6_configure_vc_mechanism(isp);
+ ipu6_buttress_restore(isp);
+
+ if (isp->need_ipc_reset) {
+ struct ipu6_buttress *b = &isp->buttress;
+
+ isp->need_ipc_reset = false;
+ ret = ipu6_buttress_ipc_reset(isp, &b->cse);
+ if (ret)
+ dev_err(&isp->pdev->dev, "IPC reset protocol failed\n");
+ }
+
+ return 0;
+}
+
+static const struct dev_pm_ops ipu6_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(&ipu6_suspend, &ipu6_resume)
+ SET_RUNTIME_PM_OPS(&ipu6_suspend, &ipu6_runtime_resume, NULL)
+};
+
+static const struct pci_device_id ipu6_pci_tbl[] = {
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IPU6) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IPU6SE) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IPU6EP_ADLP) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IPU6EP_ADLN) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IPU6EP_RPLP) },
+ { PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_IPU6EP_MTL) },
+ { }
+};
+MODULE_DEVICE_TABLE(pci, ipu6_pci_tbl);
+
+static const struct pci_error_handlers pci_err_handlers = {
+ .reset_prepare = ipu6_pci_reset_prepare,
+ .reset_done = ipu6_pci_reset_done,
+};
+
+static struct pci_driver ipu6_pci_driver = {
+ .name = IPU6_NAME,
+ .id_table = ipu6_pci_tbl,
+ .probe = ipu6_pci_probe,
+ .remove = ipu6_pci_remove,
+ .driver = {
+ .pm = pm_ptr(&ipu6_pm_ops),
+ },
+ .err_handler = &pci_err_handlers,
+};
+
+module_pci_driver(ipu6_pci_driver);
+
+MODULE_IMPORT_NS(INTEL_IPU_BRIDGE);
+MODULE_AUTHOR("Sakari Ailus <sakari.ailus@linux.intel.com>");
+MODULE_AUTHOR("Tianshu Qiu <tian.shu.qiu@intel.com>");
+MODULE_AUTHOR("Bingbu Cao <bingbu.cao@intel.com>");
+MODULE_AUTHOR("Qingwu Zhang <qingwu.zhang@intel.com>");
+MODULE_AUTHOR("Yunliang Ding <yunliang.ding@intel.com>");
+MODULE_AUTHOR("Hongju Wang <hongju.wang@intel.com>");
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Intel IPU6 PCI driver");
new file mode 100644
@@ -0,0 +1,352 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (C) 2013 - 2023 Intel Corporation */
+
+#ifndef IPU6_H
+#define IPU6_H
+
+#include <linux/firmware.h>
+#include <linux/pci.h>
+
+#include "ipu6-buttress.h"
+
+#define PCI_DEVICE_ID_INTEL_IPU6 0x9a19
+#define PCI_DEVICE_ID_INTEL_IPU6SE 0x4e19
+#define PCI_DEVICE_ID_INTEL_IPU6EP_ADLP 0x465d
+#define PCI_DEVICE_ID_INTEL_IPU6EP_ADLN 0x462e
+#define PCI_DEVICE_ID_INTEL_IPU6EP_RPLP 0xa75d
+#define PCI_DEVICE_ID_INTEL_IPU6EP_MTL 0x7d19
+
+#define IPU6_NAME "intel-ipu6"
+#define IPU6_MEDIA_DEV_MODEL_NAME "ipu6"
+
+#define IPU6SE_FIRMWARE_NAME "intel/ipu6se_fw.bin"
+#define IPU6EP_FIRMWARE_NAME "intel/ipu6ep_fw.bin"
+#define IPU6_FIRMWARE_NAME "intel/ipu6_fw.bin"
+#define IPU6EPMTL_FIRMWARE_NAME "intel/ipu6epmtl_fw.bin"
+
+enum ipu6_version {
+ IPU6_VER_INVALID = 0,
+ IPU6_VER_6 = 1,
+ IPU6_VER_6SE = 3,
+ IPU6_VER_6EP = 5,
+ IPU6_VER_6EP_MTL = 6,
+};
+
+/*
+ * IPU6 - TGL
+ * IPU6SE - JSL
+ * IPU6EP - ADL/RPL
+ * IPU6EP_MTL - MTL
+ */
+static inline bool is_ipu6se(u8 hw_ver)
+{
+ return hw_ver == IPU6_VER_6SE;
+}
+
+static inline bool is_ipu6ep(u8 hw_ver)
+{
+ return hw_ver == IPU6_VER_6EP;
+}
+
+static inline bool is_ipu6ep_mtl(u8 hw_ver)
+{
+ return hw_ver == IPU6_VER_6EP_MTL;
+}
+
+static inline bool is_ipu6_tgl(u8 hw_ver)
+{
+ return hw_ver == IPU6_VER_6;
+}
+
+/*
+ * ISYS DMA can overshoot. For higher resolutions over allocation is one line
+ * but it must be at minimum 1024 bytes. Value could be different in
+ * different versions / generations thus provide it via platform data.
+ */
+#define IPU6_ISYS_OVERALLOC_MIN 1024
+
+/* Physical pages in GDA is 128, page size is 2K for IPU6, 1K for others */
+#define IPU6_DEVICE_GDA_NR_PAGES 128
+
+/* Virtualization factor to calculate the available virtual pages */
+#define IPU6_DEVICE_GDA_VIRT_FACTOR 32
+
+#define NR_OF_MMU_RESOURCES 2
+
+struct ipu6_device {
+ struct pci_dev *pdev;
+ struct list_head devices;
+ struct ipu6_bus_device *isys;
+ struct ipu6_bus_device *psys;
+ struct ipu6_buttress buttress;
+
+ const struct firmware *cpd_fw;
+ const char *cpd_fw_name;
+ u32 cpd_metadata_cmpnt_size;
+
+ void __iomem *base;
+ struct ipu6_trace *trace;
+ bool need_ipc_reset;
+ bool secure_mode;
+ u8 hw_ver;
+ bool bus_ready_to_probe;
+};
+
+#define IPU6_ISYS_NAME "isys"
+#define IPU6_PSYS_NAME "psys"
+
+#define IPU6_MMU_MAX_DEVICES 4
+#define IPU6_MMU_ADDR_BITS 32
+/* The firmware is accessible within the first 2 GiB only in non-secure mode. */
+#define IPU6_MMU_ADDR_BITS_NON_SECURE 31
+
+#define IPU6_MMU_MAX_TLB_L1_STREAMS 32
+#define IPU6_MMU_MAX_TLB_L2_STREAMS 32
+#define IPU6_MAX_LI_BLOCK_ADDR 128
+#define IPU6_MAX_L2_BLOCK_ADDR 64
+
+#define IPU6_ISYS_MAX_CSI2_LEGACY_PORTS 4
+#define IPU6_ISYS_MAX_CSI2_COMBO_PORTS 2
+
+#define IPU6_MAX_FRAME_COUNTER 0xff
+
+#define IPU6SE_ISYS_NUM_STREAMS IPU6SE_NONSECURE_STREAM_ID_MAX
+#define IPU6_ISYS_NUM_STREAMS IPU6_NONSECURE_STREAM_ID_MAX
+
+/*
+ * To maximize the IOSF utlization, IPU6 need to send requests in bursts.
+ * At the DMA interface with the buttress, there are CDC FIFOs with burst
+ * collection capability. CDC FIFO burst collectors have a configurable
+ * threshold and is configured based on the outcome of performance measurements.
+ *
+ * isys has 3 ports with IOSF interface for VC0, VC1 and VC2
+ * psys has 4 ports with IOSF interface for VC0, VC1w, VC1r and VC2
+ *
+ * Threshold values are pre-defined and are arrived at after performance
+ * evaluations on a type of IPU6
+ */
+#define IPU6_MAX_VC_IOSF_PORTS 4
+
+/*
+ * IPU6 must configure correct arbitration mechanism related to the IOSF VC
+ * requests. There are two options per VC0 and VC1 - > 0 means rearbitrate on
+ * stall and 1 means stall until the request is completed.
+ */
+#define IPU6_BTRS_ARB_MODE_TYPE_REARB 0
+#define IPU6_BTRS_ARB_MODE_TYPE_STALL 1
+
+/* Currently chosen arbitration mechanism for VC0 */
+#define IPU6_BTRS_ARB_STALL_MODE_VC0 \
+ IPU6_BTRS_ARB_MODE_TYPE_REARB
+
+/* Currently chosen arbitration mechanism for VC1 */
+#define IPU6_BTRS_ARB_STALL_MODE_VC1 \
+ IPU6_BTRS_ARB_MODE_TYPE_REARB
+
+/*
+ * MMU Invalidation HW bug workaround by ZLW mechanism
+ *
+ * Old IPU6 MMUV2 has a bug in the invalidation mechanism which might result in
+ * wrong translation or replication of the translation. This will cause data
+ * corruption. So we cannot directly use the MMU V2 invalidation registers
+ * to invalidate the MMU. Instead, whenever an invalidate is called, we need to
+ * clear the TLB by evicting all the valid translations by filling it with trash
+ * buffer (which is guaranteed not to be used by any other processes). ZLW is
+ * used to fill the L1 and L2 caches with the trash buffer translations. ZLW
+ * or Zero length write, is pre-fetch mechanism to pre-fetch the pages in
+ * advance to the L1 and L2 caches without triggering any memory operations.
+ *
+ * In MMU V2, L1 -> 16 streams and 64 blocks, maximum 16 blocks per stream
+ * One L1 block has 16 entries, hence points to 16 * 4K pages
+ * L2 -> 16 streams and 32 blocks. 2 blocks per streams
+ * One L2 block maps to 1024 L1 entries, hence points to 4MB address range
+ * 2 blocks per L2 stream means, 1 stream points to 8MB range
+ *
+ * As we need to clear the caches and 8MB being the biggest cache size, we need
+ * to have trash buffer which points to 8MB address range. As these trash
+ * buffers are not used for any memory transactions, we need only the least
+ * amount of physical memory. So we reserve 8MB IOVA address range but only
+ * one page is reserved from physical memory. Each of this 8MB IOVA address
+ * range is then mapped to the same physical memory page.
+ */
+/* One L2 entry maps 1024 L1 entries and one L1 entry per page */
+#define IPU6_MMUV2_L2_RANGE (1024 * PAGE_SIZE)
+/* Max L2 blocks per stream */
+#define IPU6_MMUV2_MAX_L2_BLOCKS 2
+/* Max L1 blocks per stream */
+#define IPU6_MMUV2_MAX_L1_BLOCKS 16
+#define IPU6_MMUV2_TRASH_RANGE (IPU6_MMUV2_L2_RANGE * IPU6_MMUV2_MAX_L2_BLOCKS)
+/* Entries per L1 block */
+#define MMUV2_ENTRIES_PER_L1_BLOCK 16
+#define MMUV2_TRASH_L1_BLOCK_OFFSET (MMUV2_ENTRIES_PER_L1_BLOCK * PAGE_SIZE)
+#define MMUV2_TRASH_L2_BLOCK_OFFSET IPU6_MMUV2_L2_RANGE
+
+/*
+ * In some of the IPU6 MMUs, there is provision to configure L1 and L2 page
+ * table caches. Both these L1 and L2 caches are divided into multiple sections
+ * called streams. There is maximum 16 streams for both caches. Each of these
+ * sections are subdivided into multiple blocks. When nr_l1streams = 0 and
+ * nr_l2streams = 0, means the MMU is of type MMU_V1 and do not support
+ * L1/L2 page table caches.
+ *
+ * L1 stream per block sizes are configurable and varies per usecase.
+ * L2 has constant block sizes - 2 blocks per stream.
+ *
+ * MMU1 support pre-fetching of the pages to have less cache lookup misses. To
+ * enable the pre-fetching, MMU1 AT (Address Translator) device registers
+ * need to be configured.
+ *
+ * There are four types of memory accesses which requires ZLW configuration.
+ * ZLW(Zero Length Write) is a mechanism to enable VT-d pre-fetching on IOMMU.
+ *
+ * 1. Sequential Access or 1D mode
+ * Set ZLW_EN -> 1
+ * set ZLW_PAGE_CROSS_1D -> 1
+ * Set ZLW_N to "N" pages so that ZLW will be inserte N pages ahead where
+ * N is pre-defined and hardcoded in the platform data
+ * Set ZLW_2D -> 0
+ *
+ * 2. ZLW 2D mode
+ * Set ZLW_EN -> 1
+ * set ZLW_PAGE_CROSS_1D -> 1,
+ * Set ZLW_N -> 0
+ * Set ZLW_2D -> 1
+ *
+ * 3. ZLW Enable (no 1D or 2D mode)
+ * Set ZLW_EN -> 1
+ * set ZLW_PAGE_CROSS_1D -> 0,
+ * Set ZLW_N -> 0
+ * Set ZLW_2D -> 0
+ *
+ * 4. ZLW disable
+ * Set ZLW_EN -> 0
+ * set ZLW_PAGE_CROSS_1D -> 0,
+ * Set ZLW_N -> 0
+ * Set ZLW_2D -> 0
+ *
+ * To configure the ZLW for the above memory access, four registers are
+ * available. Hence to track these four settings, we have the following entries
+ * in the struct ipu6_mmu_hw. Each of these entries are per stream and
+ * available only for the L1 streams.
+ *
+ * a. l1_zlw_en -> To track zlw enabled per stream (ZLW_EN)
+ * b. l1_zlw_1d_mode -> Track 1D mode per stream. ZLW inserted at page boundary
+ * c. l1_ins_zlw_ahead_pages -> to track how advance the ZLW need to be inserted
+ * Insert ZLW request N pages ahead address.
+ * d. l1_zlw_2d_mode -> To track 2D mode per stream (ZLW_2D)
+ *
+ *
+ * Currently L1/L2 streams, blocks, AT ZLW configurations etc. are pre-defined
+ * as per the usecase specific calculations. Any change to this pre-defined
+ * table has to happen in sync with IPU6 FW.
+ */
+struct ipu6_mmu_hw {
+ union {
+ unsigned long offset;
+ void __iomem *base;
+ };
+ u32 info_bits;
+ u8 nr_l1streams;
+ /*
+ * L1 has variable blocks per stream - total of 64 blocks and maximum of
+ * 16 blocks per stream. Configurable by using the block start address
+ * per stream. Block start address is calculated from the block size
+ */
+ u8 l1_block_sz[IPU6_MMU_MAX_TLB_L1_STREAMS];
+ /* Is ZLW is enabled in each stream */
+ bool l1_zlw_en[IPU6_MMU_MAX_TLB_L1_STREAMS];
+ bool l1_zlw_1d_mode[IPU6_MMU_MAX_TLB_L1_STREAMS];
+ u8 l1_ins_zlw_ahead_pages[IPU6_MMU_MAX_TLB_L1_STREAMS];
+ bool l1_zlw_2d_mode[IPU6_MMU_MAX_TLB_L1_STREAMS];
+
+ u32 l1_stream_id_reg_offset;
+ u32 l2_stream_id_reg_offset;
+
+ u8 nr_l2streams;
+ /*
+ * L2 has fixed 2 blocks per stream. Block address is calculated
+ * from the block size
+ */
+ u8 l2_block_sz[IPU6_MMU_MAX_TLB_L2_STREAMS];
+ /* flag to track if WA is needed for successive invalidate HW bug */
+ bool insert_read_before_invalidate;
+};
+
+struct ipu6_mmu_pdata {
+ u32 nr_mmus;
+ struct ipu6_mmu_hw mmu_hw[IPU6_MMU_MAX_DEVICES];
+ int mmid;
+};
+
+struct ipu6_isys_csi2_pdata {
+ void __iomem *base;
+};
+
+struct ipu6_isys_internal_csi2_pdata {
+ u32 nports;
+ u32 irq_mask;
+ u32 *offsets;
+ u32 ctrl0_irq_edge;
+ u32 ctrl0_irq_clear;
+ u32 ctrl0_irq_mask;
+ u32 ctrl0_irq_enable;
+ u32 ctrl0_irq_lnp;
+ u32 ctrl0_irq_status;
+ u32 fw_access_port_ofs;
+};
+
+struct ipu6_isys_internal_tpg_pdata {
+ u32 ntpgs;
+ u32 *offsets;
+ u32 *sels;
+};
+
+struct ipu6_hw_variants {
+ unsigned long offset;
+ u32 nr_mmus;
+ struct ipu6_mmu_hw mmu_hw[IPU6_MMU_MAX_DEVICES];
+ u8 cdc_fifos;
+ u8 cdc_fifo_threshold[IPU6_MAX_VC_IOSF_PORTS];
+ u32 dmem_offset;
+ u32 spc_offset;
+};
+
+struct ipu6_isys_internal_pdata {
+ struct ipu6_isys_internal_csi2_pdata csi2;
+ struct ipu6_hw_variants hw_variant;
+ u32 num_parallel_streams;
+ u32 isys_dma_overshoot;
+ u32 sram_gran_shift;
+ u32 sram_gran_size;
+ u32 max_sram_size;
+ u32 max_streams;
+ u32 max_send_queues;
+ u32 max_sram_blocks;
+ u32 max_devq_size;
+ u32 sensor_type_start;
+ u32 sensor_type_end;
+ u32 ltr;
+ u32 memopen_threshold;
+ bool enhanced_iwake;
+};
+
+struct ipu6_isys_pdata {
+ void __iomem *base;
+ const struct ipu6_isys_internal_pdata *ipdata;
+};
+
+struct ipu6_psys_internal_pdata {
+ struct ipu6_hw_variants hw_variant;
+};
+
+struct ipu6_psys_pdata {
+ void __iomem *base;
+ const struct ipu6_psys_internal_pdata *ipdata;
+};
+
+int ipu6_fw_authenticate(void *data, u64 val);
+void ipu6_configure_spc(struct ipu6_device *isp,
+ const struct ipu6_hw_variants *hw_variant,
+ int pkg_dir_idx, void __iomem *base, u64 *pkg_dir,
+ dma_addr_t pkg_dir_dma_addr);
+#endif /* IPU6_H */