@@ -157,6 +157,7 @@ Hardware Monitoring Kernel Drivers
mp2888
mp2975
mp5023
+ mp5990
nct6683
nct6775
nct7802
new file mode 100644
@@ -0,0 +1,84 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Kernel driver mp5990
+====================
+
+Supported chips:
+
+ * MPS MP5990
+
+ Prefix: 'mp5990'
+
+ * Datasheet
+
+ Publicly available at the MPS website : https://www.monolithicpower.com/en/mp5990.html
+
+Author:
+
+ Peter Yin <peteryin.openbmc@gmail.com>
+
+Description
+-----------
+
+This driver implements support for Monolithic Power Systems, Inc. (MPS)
+MP5990 Hot-Swap Controller.
+
+Device compliant with:
+
+- PMBus rev 1.3 interface.
+
+Device supports direct and linear format for reading input voltage,
+output voltage, output current, input power and temperature.
+
+The driver exports the following attributes via the 'sysfs' files
+for input voltage:
+
+**in1_input**
+
+**in1_label**
+
+**in1_max**
+
+**in1_max_alarm**
+
+**in1_min**
+
+**in1_min_alarm**
+
+The driver provides the following attributes for output voltage:
+
+**in2_input**
+
+**in2_label**
+
+**in2_alarm**
+
+The driver provides the following attributes for output current:
+
+**curr1_input**
+
+**curr1_label**
+
+**curr1_alarm**
+
+**curr1_max**
+
+The driver provides the following attributes for input power:
+
+**power1_input**
+
+**power1_label**
+
+**power1_alarm**
+
+The driver provides the following attributes for temperature:
+
+**temp1_input**
+
+**temp1_max**
+
+**temp1_max_alarm**
+
+**temp1_crit**
+
+**temp1_crit_alarm**
@@ -326,6 +326,15 @@ config SENSORS_MP5023
This driver can also be built as a module. If so, the module will
be called mp5023.
+config SENSORS_MP5990
+ tristate "MPS MP5990"
+ help
+ If you say yes here you get hardware monitoring support for MPS
+ MP5990.
+
+ This driver can also be built as a module. If so, the module will
+ be called mp5990.
+
config SENSORS_MPQ7932_REGULATOR
bool "Regulator support for MPQ7932"
depends on SENSORS_MPQ7932 && REGULATOR
@@ -35,6 +35,7 @@ obj-$(CONFIG_SENSORS_MAX8688) += max8688.o
obj-$(CONFIG_SENSORS_MP2888) += mp2888.o
obj-$(CONFIG_SENSORS_MP2975) += mp2975.o
obj-$(CONFIG_SENSORS_MP5023) += mp5023.o
+obj-$(CONFIG_SENSORS_MP5990) += mp5990.o
obj-$(CONFIG_SENSORS_MPQ7932) += mpq7932.o
obj-$(CONFIG_SENSORS_PLI1209BC) += pli1209bc.o
obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
new file mode 100644
@@ -0,0 +1,177 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Driver for MPS MP5990 Hot-Swap Controller
+ */
+
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include "pmbus.h"
+
+#define MP5990_EFUSE_CFG (0xC4)
+#define MP5990_VOUT_FORMAT BIT(9)
+
+struct mp5990_data {
+ struct pmbus_driver_info info;
+ u8 vout_mode;
+ u8 vout_linear_exponent;
+};
+
+#define to_mp5990_data(x) container_of(x, struct mp5990_data, info)
+
+static int mp5990_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct mp5990_data *data = to_mp5990_data(info);
+
+ switch (reg) {
+ case PMBUS_VOUT_MODE:
+ if (data->vout_mode == linear) {
+ /*
+ * The VOUT format is linear11, not linear16.
+ * We should enforce the VOUT in linear mode and
+ * return exponent value.
+ */
+ return data->vout_linear_exponent;
+ }
+
+ /*
+ * The datasheet does not support the VOUT command,
+ * but the device responds with a default value of 0x17.
+ * In the standard, 0x17 represents linear mode. However,
+ * Therefore, we should enforce the VOUT in the direct format
+ * when format use default direct mode.
+ */
+ return PB_VOUT_MODE_DIRECT;
+
+ default:
+ return -ENODATA;
+ }
+}
+
+static int mp5990_read_word_data(struct i2c_client *client, int page,
+ int phase, int reg)
+{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+ struct mp5990_data *data = to_mp5990_data(info);
+ int ret;
+ s32 mantissa;
+
+ switch (reg) {
+ case PMBUS_READ_VOUT:
+ ret = pmbus_read_word_data(client, page, phase, reg);
+ if (ret < 0)
+ return ret;
+ /*
+ * Because the VOUT mode is linear11 and not linear16,
+ * we disregard bits[15:11] and report based on the VOUT mode.
+ */
+ if (data->vout_mode == linear) {
+ mantissa = ((s16)((ret & 0x7ff) << 5)) >> 5;
+ ret = mantissa;
+ }
+ break;
+ default:
+ return -ENODATA;
+ }
+
+ return ret;
+}
+
+static struct pmbus_driver_info mp5990_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = direct,
+ .format[PSC_VOLTAGE_OUT] = direct,
+ .format[PSC_CURRENT_OUT] = direct,
+ .format[PSC_POWER] = direct,
+ .format[PSC_TEMPERATURE] = direct,
+ .m[PSC_VOLTAGE_IN] = 32,
+ .b[PSC_VOLTAGE_IN] = 0,
+ .R[PSC_VOLTAGE_IN] = 0,
+ .m[PSC_VOLTAGE_OUT] = 32,
+ .b[PSC_VOLTAGE_OUT] = 0,
+ .R[PSC_VOLTAGE_OUT] = 0,
+ .m[PSC_CURRENT_OUT] = 16,
+ .b[PSC_CURRENT_OUT] = 0,
+ .R[PSC_CURRENT_OUT] = 0,
+ .m[PSC_POWER] = 1,
+ .b[PSC_POWER] = 0,
+ .R[PSC_POWER] = 0,
+ .m[PSC_TEMPERATURE] = 1,
+ .b[PSC_TEMPERATURE] = 0,
+ .R[PSC_TEMPERATURE] = 0,
+ .func[0] =
+ PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT | PMBUS_HAVE_PIN |
+ PMBUS_HAVE_TEMP | PMBUS_HAVE_IOUT |
+ PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_STATUS_TEMP,
+ .read_byte_data = mp5990_read_byte_data,
+ .read_word_data = mp5990_read_word_data,
+};
+
+static int mp5990_probe(struct i2c_client *client)
+{
+ struct pmbus_driver_info *info;
+ struct mp5990_data *data;
+ int ret;
+
+ data = devm_kzalloc(&client->dev, sizeof(struct mp5990_data),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ memcpy(&data->info, &mp5990_info, sizeof(*info));
+ info = &data->info;
+
+ /* Read Vout Config */
+ ret = i2c_smbus_read_word_data(client, MP5990_EFUSE_CFG);
+ if (ret < 0) {
+ dev_err(&client->dev, "Can't get vout mode.");
+ return ret;
+ }
+
+ /*
+ * EFUSE_CFG (0xC4) bit9=1 is linear mode, bit=0 is direct mode.
+ */
+ if (ret & MP5990_VOUT_FORMAT) {
+ data->vout_mode = linear;
+ data->info.format[PSC_VOLTAGE_IN] = linear;
+ data->info.format[PSC_VOLTAGE_OUT] = linear;
+ data->info.format[PSC_CURRENT_OUT] = linear;
+ data->info.format[PSC_POWER] = linear;
+ ret = i2c_smbus_read_word_data(client, PMBUS_READ_VOUT);
+ if (ret < 0) {
+ dev_err(&client->dev, "Can't get vout exponent.");
+ return ret;
+ }
+ data->vout_linear_exponent = (u8)((ret >> 11) & 0x1f);
+ } else {
+ data->vout_mode = direct;
+ }
+ return pmbus_do_probe(client, info);
+}
+
+static const struct of_device_id mp5990_of_match[] = {
+ { .compatible = "mps,mp5990" },
+ {}
+};
+
+static const struct i2c_device_id mp5990_id[] = {
+ {"mp5990", 0},
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, mp5990_id);
+
+static struct i2c_driver mp5990_driver = {
+ .driver = {
+ .name = "mp5990",
+ .of_match_table = mp5990_of_match,
+ },
+ .probe = mp5990_probe,
+ .id_table = mp5990_id,
+};
+module_i2c_driver(mp5990_driver);
+
+MODULE_AUTHOR("Peter Yin <peter.yin@quantatw.com>");
+MODULE_DESCRIPTION("PMBus driver for MP5990 HSC");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(PMBUS);
Add support for mp5990 device from Monolithic Power Systems, Inc. (MPS) vendor. This is a Hot-Swap Controller. Signed-off-by: Peter Yin <peteryin.openbmc@gmail.com> --- Documentation/hwmon/index.rst | 1 + Documentation/hwmon/mp5990.rst | 84 ++++++++++++++++ drivers/hwmon/pmbus/Kconfig | 9 ++ drivers/hwmon/pmbus/Makefile | 1 + drivers/hwmon/pmbus/mp5990.c | 177 +++++++++++++++++++++++++++++++++ 5 files changed, 272 insertions(+) create mode 100644 Documentation/hwmon/mp5990.rst create mode 100644 drivers/hwmon/pmbus/mp5990.c