| Message ID | 20231201160925.3136868-15-peter.griffin@linaro.org (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
| Series | Add minimal Tensor/GS101 SoC support and Oriole/Pixel6 board | expand |
On 12/01/2023, Peter Griffin wrote: > Add support for the pin-controller found on the gs101 SoC used in > Pixel 6 phones. > > Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Tested-by: Will McVicker <willmcvicker@google.com> --- I verified boot and that the pinctrl probes. Regards, Will > --- > .../pinctrl/samsung/pinctrl-exynos-arm64.c | 159 ++++++++++++++++++ > drivers/pinctrl/samsung/pinctrl-exynos.c | 2 + > drivers/pinctrl/samsung/pinctrl-exynos.h | 34 ++++ > drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + > drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + > 5 files changed, 198 insertions(+) > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > index cb965cf93705..e1a0668ecb16 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data fsd_of_data __initconst = { > .ctrl = fsd_pin_ctrl, > .num_ctrl = ARRAY_SIZE(fsd_pin_ctrl), > }; > + > +/* > + * bank type for non-alive type > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit field: 4) > + * (CONPDN bit field: 2, PUDPDN bit field: 4) > + */ > +static struct samsung_pin_bank_type gs101_bank_type_off = { > + .fld_width = { 4, 1, 4, 4, 2, 4, }, > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, > +}; > + > +/* > + * bank type for alive type > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit field: 4) > + */ > +static const struct samsung_pin_bank_type gs101_bank_type_alive = { > + .fld_width = { 4, 1, 4, 4, }, > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, > +}; > + > +/* pin banks of gs101 pin-controller (ALIVE) */ > +static const struct samsung_pin_bank_data gs101_pin_alive[] = { > + EXYNOS9_PIN_BANK_EINTW(8, 0x0, "gpa0", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTW(7, 0x20, "gpa1", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTW(5, 0x40, "gpa2", 0x08, 0x10), > + EXYNOS9_PIN_BANK_EINTW(4, 0x60, "gpa3", 0x0c, 0x18), > + EXYNOS9_PIN_BANK_EINTW(4, 0x80, "gpa4", 0x10, 0x1c), > + EXYNOS9_PIN_BANK_EINTW(7, 0xa0, "gpa5", 0x14, 0x20), > + EXYNOS9_PIN_BANK_EINTW(8, 0xc0, "gpa9", 0x18, 0x28), > + EXYNOS9_PIN_BANK_EINTW(2, 0xe0, "gpa10", 0x1c, 0x30), > +}; > + > +/* pin banks of gs101 pin-controller (FAR_ALIVE) */ > +static const struct samsung_pin_bank_data gs101_pin_far_alive[] = { > + EXYNOS9_PIN_BANK_EINTW(8, 0x0, "gpa6", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTW(4, 0x20, "gpa7", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTW(8, 0x40, "gpa8", 0x08, 0x0c), > + EXYNOS9_PIN_BANK_EINTW(2, 0x60, "gpa11", 0x0c, 0x14), > +}; > + > +/* pin banks of gs101 pin-controller (GSACORE) */ > +static const struct samsung_pin_bank_data gs101_pin_gsacore[] = { > + EXYNOS9_PIN_BANK_EINTG(2, 0x0, "gps0", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(8, 0x20, "gps1", 0x04, 0x04), > + EXYNOS9_PIN_BANK_EINTG(3, 0x40, "gps2", 0x08, 0x0c), > +}; > + > +/* pin banks of gs101 pin-controller (GSACTRL) */ > +static const struct samsung_pin_bank_data gs101_pin_gsactrl[] = { > + EXYNOS9_PIN_BANK_EINTW(6, 0x0, "gps3", 0x00, 0x00), > +}; > + > +/* pin banks of gs101 pin-controller (PERIC0) */ > +static const struct samsung_pin_bank_data gs101_pin_peric0[] = { > + EXYNOS9_PIN_BANK_EINTG(5, 0x0, "gpp0", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(4, 0x20, "gpp1", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTG(4, 0x40, "gpp2", 0x08, 0x0c), > + EXYNOS9_PIN_BANK_EINTG(2, 0x60, "gpp3", 0x0c, 0x10), > + EXYNOS9_PIN_BANK_EINTG(4, 0x80, "gpp4", 0x10, 0x14), > + EXYNOS9_PIN_BANK_EINTG(2, 0xa0, "gpp5", 0x14, 0x18), > + EXYNOS9_PIN_BANK_EINTG(4, 0xc0, "gpp6", 0x18, 0x1c), > + EXYNOS9_PIN_BANK_EINTG(2, 0xe0, "gpp7", 0x1c, 0x20), > + EXYNOS9_PIN_BANK_EINTG(4, 0x100, "gpp8", 0x20, 0x24), > + EXYNOS9_PIN_BANK_EINTG(2, 0x120, "gpp9", 0x24, 0x28), > + EXYNOS9_PIN_BANK_EINTG(4, 0x140, "gpp10", 0x28, 0x2c), > + EXYNOS9_PIN_BANK_EINTG(2, 0x160, "gpp11", 0x2c, 0x30), > + EXYNOS9_PIN_BANK_EINTG(4, 0x180, "gpp12", 0x30, 0x34), > + EXYNOS9_PIN_BANK_EINTG(2, 0x1a0, "gpp13", 0x34, 0x38), > + EXYNOS9_PIN_BANK_EINTG(4, 0x1c0, "gpp14", 0x38, 0x3c), > + EXYNOS9_PIN_BANK_EINTG(2, 0x1e0, "gpp15", 0x3c, 0x40), > + EXYNOS9_PIN_BANK_EINTG(4, 0x200, "gpp16", 0x40, 0x44), > + EXYNOS9_PIN_BANK_EINTG(2, 0x220, "gpp17", 0x44, 0x48), > + EXYNOS9_PIN_BANK_EINTG(4, 0x240, "gpp18", 0x48, 0x4c), > + EXYNOS9_PIN_BANK_EINTG(4, 0x260, "gpp19", 0x4c, 0x50), > +}; > + > +/* pin banks of gs101 pin-controller (PERIC1) */ > +static const struct samsung_pin_bank_data gs101_pin_peric1[] = { > + EXYNOS9_PIN_BANK_EINTG(8, 0x0, "gpp20", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(4, 0x20, "gpp21", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTG(2, 0x40, "gpp22", 0x08, 0x0c), > + EXYNOS9_PIN_BANK_EINTG(8, 0x60, "gpp23", 0x0c, 0x10), > + EXYNOS9_PIN_BANK_EINTG(4, 0x80, "gpp24", 0x10, 0x18), > + EXYNOS9_PIN_BANK_EINTG(4, 0xa0, "gpp25", 0x14, 0x1c), > + EXYNOS9_PIN_BANK_EINTG(5, 0xc0, "gpp26", 0x18, 0x20), > + EXYNOS9_PIN_BANK_EINTG(4, 0xe0, "gpp27", 0x1c, 0x28), > +}; > + > +/* pin banks of gs101 pin-controller (HSI1) */ > +static const struct samsung_pin_bank_data gs101_pin_hsi1[] = { > + EXYNOS9_PIN_BANK_EINTG(6, 0x0, "gph0", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(7, 0x20, "gph1", 0x04, 0x08), > +}; > + > +/* pin banks of gs101 pin-controller (HSI2) */ > +static const struct samsung_pin_bank_data gs101_pin_hsi2[] = { > + EXYNOS9_PIN_BANK_EINTG(6, 0x0, "gph2", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(2, 0x20, "gph3", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTG(6, 0x40, "gph4", 0x08, 0x0c), > +}; > + > +static const struct samsung_pin_ctrl gs101_pin_ctrl[] __initconst = { > + { > + /* pin banks of gs101 pin-controller (ALIVE) */ > + .pin_banks = gs101_pin_alive, > + .nr_banks = ARRAY_SIZE(gs101_pin_alive), > + .eint_wkup_init = exynos_eint_wkup_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (FAR_ALIVE) */ > + .pin_banks = gs101_pin_far_alive, > + .nr_banks = ARRAY_SIZE(gs101_pin_far_alive), > + .eint_wkup_init = exynos_eint_wkup_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (GSACORE) */ > + .pin_banks = gs101_pin_gsacore, > + .nr_banks = ARRAY_SIZE(gs101_pin_gsacore), > + }, { > + /* pin banks of gs101 pin-controller (GSACTRL) */ > + .pin_banks = gs101_pin_gsactrl, > + .nr_banks = ARRAY_SIZE(gs101_pin_gsactrl), > + }, { > + /* pin banks of gs101 pin-controller (PERIC0) */ > + .pin_banks = gs101_pin_peric0, > + .nr_banks = ARRAY_SIZE(gs101_pin_peric0), > + .eint_gpio_init = exynos_eint_gpio_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (PERIC1) */ > + .pin_banks = gs101_pin_peric1, > + .nr_banks = ARRAY_SIZE(gs101_pin_peric1), > + .eint_gpio_init = exynos_eint_gpio_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (HSI1) */ > + .pin_banks = gs101_pin_hsi1, > + .nr_banks = ARRAY_SIZE(gs101_pin_hsi1), > + .eint_gpio_init = exynos_eint_gpio_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (HSI2) */ > + .pin_banks = gs101_pin_hsi2, > + .nr_banks = ARRAY_SIZE(gs101_pin_hsi2), > + .eint_gpio_init = exynos_eint_gpio_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, > +}; > + > +const struct samsung_pinctrl_of_match_data gs101_of_data __initconst = { > + .ctrl = gs101_pin_ctrl, > + .num_ctrl = ARRAY_SIZE(gs101_pin_ctrl), > +}; > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c > index 56fc11a1fe2f..75b9cf72ce73 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c > @@ -537,6 +537,8 @@ static const struct of_device_id exynos_wkup_irq_ids[] = { > .data = &exynos7_wkup_irq_chip }, > { .compatible = "samsung,exynosautov9-wakeup-eint", > .data = &exynos7_wkup_irq_chip }, > + { .compatible = "google,gs101-wakeup-eint", > + .data = &exynos7_wkup_irq_chip }, > { } > }; > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h > index e2799ff1b5e9..1ffc90db079d 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos.h > +++ b/drivers/pinctrl/samsung/pinctrl-exynos.h > @@ -147,6 +147,40 @@ > .name = id \ > } > > +#define EXYNOS9_PIN_BANK_EINTN(types, pins, reg, id) \ > + { \ > + .type = &types, \ > + .pctl_offset = reg, \ > + .nr_pins = pins, \ > + .eint_type = EINT_TYPE_NONE, \ > + .fltcon_type = FLT_DEFAULT \ > + .name = id \ > + } > + > +#define EXYNOS9_PIN_BANK_EINTG(pins, reg, id, offs, fltcon_offs) \ > + { \ > + .type = &gs101_bank_type_off, \ > + .pctl_offset = reg, \ > + .nr_pins = pins, \ > + .eint_type = EINT_TYPE_GPIO, \ > + .eint_offset = offs, \ > + .fltcon_type = FLT_DEFAULT, \ > + .fltcon_offset = fltcon_offs, \ > + .name = id \ > + } > + > +#define EXYNOS9_PIN_BANK_EINTW(pins, reg, id, offs, fltcon_offs) \ > + { \ > + .type = &gs101_bank_type_alive, \ > + .pctl_offset = reg, \ > + .nr_pins = pins, \ > + .eint_type = EINT_TYPE_WKUP, \ > + .eint_offset = offs, \ > + .fltcon_type = FLT_SELECTABLE, \ > + .fltcon_offset = fltcon_offs, \ > + .name = id \ > + } > + > /** > * struct exynos_weint_data: irq specific data for all the wakeup interrupts > * generated by the external wakeup interrupt controller. > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c > index 50c360b4753a..982a5702714c 100644 > --- a/drivers/pinctrl/samsung/pinctrl-samsung.c > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c > @@ -1323,6 +1323,8 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = { > .data = &exynosautov9_of_data }, > { .compatible = "tesla,fsd-pinctrl", > .data = &fsd_of_data }, > + { .compatible = "google,gs101-pinctrl", > + .data = &gs101_of_data }, > #endif > #ifdef CONFIG_PINCTRL_S3C64XX > { .compatible = "samsung,s3c64xx-pinctrl", > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h > index 5fab3885a7d7..f6856290608c 100644 > --- a/drivers/pinctrl/samsung/pinctrl-samsung.h > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h > @@ -373,6 +373,7 @@ extern const struct samsung_pinctrl_of_match_data exynos7885_of_data; > extern const struct samsung_pinctrl_of_match_data exynos850_of_data; > extern const struct samsung_pinctrl_of_match_data exynosautov9_of_data; > extern const struct samsung_pinctrl_of_match_data fsd_of_data; > +extern const struct samsung_pinctrl_of_match_data gs101_of_data; > extern const struct samsung_pinctrl_of_match_data s3c64xx_of_data; > extern const struct samsung_pinctrl_of_match_data s3c2412_of_data; > extern const struct samsung_pinctrl_of_match_data s3c2416_of_data; > -- > 2.43.0.rc2.451.g8631bc7472-goog > > -- > To unsubscribe from this group and stop receiving emails from it, send an email to kernel-team+unsubscribe@android.com. >
On Fri, Dec 1, 2023 at 10:11 AM Peter Griffin <peter.griffin@linaro.org> wrote: > > Add support for the pin-controller found on the gs101 SoC used in > Pixel 6 phones. > > Signed-off-by: Peter Griffin <peter.griffin@linaro.org> > --- > .../pinctrl/samsung/pinctrl-exynos-arm64.c | 159 ++++++++++++++++++ > drivers/pinctrl/samsung/pinctrl-exynos.c | 2 + > drivers/pinctrl/samsung/pinctrl-exynos.h | 34 ++++ > drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + > drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + > 5 files changed, 198 insertions(+) > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > index cb965cf93705..e1a0668ecb16 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data fsd_of_data __initconst = { > .ctrl = fsd_pin_ctrl, > .num_ctrl = ARRAY_SIZE(fsd_pin_ctrl), > }; > + > +/* > + * bank type for non-alive type > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit field: 4) > + * (CONPDN bit field: 2, PUDPDN bit field: 4) > + */ > +static struct samsung_pin_bank_type gs101_bank_type_off = { > + .fld_width = { 4, 1, 4, 4, 2, 4, }, > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, > +}; This is just the same as exynos850_bank_type_off (100% duplication). Here is what I suggest. Now that it's obvious there is some common platform for moder Exynos SoCs, and it's probably Exynos9, I'd suggest next course of action (if maintainers agree): 1. Remove this one 2. Rename exynos850_bank_type_off to exynos9_bank_type_off 3. Use it for both gs101 and exynos850 Does it make sense? > + > +/* > + * bank type for alive type > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit field: 4) > + */ > +static const struct samsung_pin_bank_type gs101_bank_type_alive = { > + .fld_width = { 4, 1, 4, 4, }, > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, > +}; Ditto, it's a duplication of exynos850_bank_type_alive . > + > +/* pin banks of gs101 pin-controller (ALIVE) */ > +static const struct samsung_pin_bank_data gs101_pin_alive[] = { > + EXYNOS9_PIN_BANK_EINTW(8, 0x0, "gpa0", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTW(7, 0x20, "gpa1", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTW(5, 0x40, "gpa2", 0x08, 0x10), > + EXYNOS9_PIN_BANK_EINTW(4, 0x60, "gpa3", 0x0c, 0x18), > + EXYNOS9_PIN_BANK_EINTW(4, 0x80, "gpa4", 0x10, 0x1c), > + EXYNOS9_PIN_BANK_EINTW(7, 0xa0, "gpa5", 0x14, 0x20), > + EXYNOS9_PIN_BANK_EINTW(8, 0xc0, "gpa9", 0x18, 0x28), > + EXYNOS9_PIN_BANK_EINTW(2, 0xe0, "gpa10", 0x1c, 0x30), > +}; > + > +/* pin banks of gs101 pin-controller (FAR_ALIVE) */ > +static const struct samsung_pin_bank_data gs101_pin_far_alive[] = { > + EXYNOS9_PIN_BANK_EINTW(8, 0x0, "gpa6", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTW(4, 0x20, "gpa7", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTW(8, 0x40, "gpa8", 0x08, 0x0c), > + EXYNOS9_PIN_BANK_EINTW(2, 0x60, "gpa11", 0x0c, 0x14), > +}; > + > +/* pin banks of gs101 pin-controller (GSACORE) */ > +static const struct samsung_pin_bank_data gs101_pin_gsacore[] = { > + EXYNOS9_PIN_BANK_EINTG(2, 0x0, "gps0", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(8, 0x20, "gps1", 0x04, 0x04), > + EXYNOS9_PIN_BANK_EINTG(3, 0x40, "gps2", 0x08, 0x0c), > +}; > + > +/* pin banks of gs101 pin-controller (GSACTRL) */ > +static const struct samsung_pin_bank_data gs101_pin_gsactrl[] = { > + EXYNOS9_PIN_BANK_EINTW(6, 0x0, "gps3", 0x00, 0x00), > +}; > + > +/* pin banks of gs101 pin-controller (PERIC0) */ > +static const struct samsung_pin_bank_data gs101_pin_peric0[] = { > + EXYNOS9_PIN_BANK_EINTG(5, 0x0, "gpp0", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(4, 0x20, "gpp1", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTG(4, 0x40, "gpp2", 0x08, 0x0c), > + EXYNOS9_PIN_BANK_EINTG(2, 0x60, "gpp3", 0x0c, 0x10), > + EXYNOS9_PIN_BANK_EINTG(4, 0x80, "gpp4", 0x10, 0x14), > + EXYNOS9_PIN_BANK_EINTG(2, 0xa0, "gpp5", 0x14, 0x18), > + EXYNOS9_PIN_BANK_EINTG(4, 0xc0, "gpp6", 0x18, 0x1c), > + EXYNOS9_PIN_BANK_EINTG(2, 0xe0, "gpp7", 0x1c, 0x20), > + EXYNOS9_PIN_BANK_EINTG(4, 0x100, "gpp8", 0x20, 0x24), > + EXYNOS9_PIN_BANK_EINTG(2, 0x120, "gpp9", 0x24, 0x28), > + EXYNOS9_PIN_BANK_EINTG(4, 0x140, "gpp10", 0x28, 0x2c), > + EXYNOS9_PIN_BANK_EINTG(2, 0x160, "gpp11", 0x2c, 0x30), > + EXYNOS9_PIN_BANK_EINTG(4, 0x180, "gpp12", 0x30, 0x34), > + EXYNOS9_PIN_BANK_EINTG(2, 0x1a0, "gpp13", 0x34, 0x38), > + EXYNOS9_PIN_BANK_EINTG(4, 0x1c0, "gpp14", 0x38, 0x3c), > + EXYNOS9_PIN_BANK_EINTG(2, 0x1e0, "gpp15", 0x3c, 0x40), > + EXYNOS9_PIN_BANK_EINTG(4, 0x200, "gpp16", 0x40, 0x44), > + EXYNOS9_PIN_BANK_EINTG(2, 0x220, "gpp17", 0x44, 0x48), > + EXYNOS9_PIN_BANK_EINTG(4, 0x240, "gpp18", 0x48, 0x4c), > + EXYNOS9_PIN_BANK_EINTG(4, 0x260, "gpp19", 0x4c, 0x50), > +}; > + > +/* pin banks of gs101 pin-controller (PERIC1) */ > +static const struct samsung_pin_bank_data gs101_pin_peric1[] = { > + EXYNOS9_PIN_BANK_EINTG(8, 0x0, "gpp20", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(4, 0x20, "gpp21", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTG(2, 0x40, "gpp22", 0x08, 0x0c), > + EXYNOS9_PIN_BANK_EINTG(8, 0x60, "gpp23", 0x0c, 0x10), > + EXYNOS9_PIN_BANK_EINTG(4, 0x80, "gpp24", 0x10, 0x18), > + EXYNOS9_PIN_BANK_EINTG(4, 0xa0, "gpp25", 0x14, 0x1c), > + EXYNOS9_PIN_BANK_EINTG(5, 0xc0, "gpp26", 0x18, 0x20), > + EXYNOS9_PIN_BANK_EINTG(4, 0xe0, "gpp27", 0x1c, 0x28), > +}; > + > +/* pin banks of gs101 pin-controller (HSI1) */ > +static const struct samsung_pin_bank_data gs101_pin_hsi1[] = { > + EXYNOS9_PIN_BANK_EINTG(6, 0x0, "gph0", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(7, 0x20, "gph1", 0x04, 0x08), > +}; > + > +/* pin banks of gs101 pin-controller (HSI2) */ > +static const struct samsung_pin_bank_data gs101_pin_hsi2[] = { > + EXYNOS9_PIN_BANK_EINTG(6, 0x0, "gph2", 0x00, 0x00), > + EXYNOS9_PIN_BANK_EINTG(2, 0x20, "gph3", 0x04, 0x08), > + EXYNOS9_PIN_BANK_EINTG(6, 0x40, "gph4", 0x08, 0x0c), > +}; > + > +static const struct samsung_pin_ctrl gs101_pin_ctrl[] __initconst = { > + { > + /* pin banks of gs101 pin-controller (ALIVE) */ > + .pin_banks = gs101_pin_alive, > + .nr_banks = ARRAY_SIZE(gs101_pin_alive), > + .eint_wkup_init = exynos_eint_wkup_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (FAR_ALIVE) */ > + .pin_banks = gs101_pin_far_alive, > + .nr_banks = ARRAY_SIZE(gs101_pin_far_alive), > + .eint_wkup_init = exynos_eint_wkup_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (GSACORE) */ > + .pin_banks = gs101_pin_gsacore, > + .nr_banks = ARRAY_SIZE(gs101_pin_gsacore), > + }, { > + /* pin banks of gs101 pin-controller (GSACTRL) */ > + .pin_banks = gs101_pin_gsactrl, > + .nr_banks = ARRAY_SIZE(gs101_pin_gsactrl), > + }, { > + /* pin banks of gs101 pin-controller (PERIC0) */ > + .pin_banks = gs101_pin_peric0, > + .nr_banks = ARRAY_SIZE(gs101_pin_peric0), > + .eint_gpio_init = exynos_eint_gpio_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (PERIC1) */ > + .pin_banks = gs101_pin_peric1, > + .nr_banks = ARRAY_SIZE(gs101_pin_peric1), > + .eint_gpio_init = exynos_eint_gpio_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (HSI1) */ > + .pin_banks = gs101_pin_hsi1, > + .nr_banks = ARRAY_SIZE(gs101_pin_hsi1), > + .eint_gpio_init = exynos_eint_gpio_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, { > + /* pin banks of gs101 pin-controller (HSI2) */ > + .pin_banks = gs101_pin_hsi2, > + .nr_banks = ARRAY_SIZE(gs101_pin_hsi2), > + .eint_gpio_init = exynos_eint_gpio_init, > + .suspend = exynos_pinctrl_suspend, > + .resume = exynos_pinctrl_resume, > + }, > +}; > + > +const struct samsung_pinctrl_of_match_data gs101_of_data __initconst = { > + .ctrl = gs101_pin_ctrl, > + .num_ctrl = ARRAY_SIZE(gs101_pin_ctrl), > +}; > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c > index 56fc11a1fe2f..75b9cf72ce73 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos.c > +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c > @@ -537,6 +537,8 @@ static const struct of_device_id exynos_wkup_irq_ids[] = { > .data = &exynos7_wkup_irq_chip }, > { .compatible = "samsung,exynosautov9-wakeup-eint", > .data = &exynos7_wkup_irq_chip }, > + { .compatible = "google,gs101-wakeup-eint", > + .data = &exynos7_wkup_irq_chip }, > { } > }; > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h > index e2799ff1b5e9..1ffc90db079d 100644 > --- a/drivers/pinctrl/samsung/pinctrl-exynos.h > +++ b/drivers/pinctrl/samsung/pinctrl-exynos.h > @@ -147,6 +147,40 @@ > .name = id \ > } > > +#define EXYNOS9_PIN_BANK_EINTN(types, pins, reg, id) \ > + { \ > + .type = &types, \ > + .pctl_offset = reg, \ > + .nr_pins = pins, \ > + .eint_type = EINT_TYPE_NONE, \ > + .fltcon_type = FLT_DEFAULT \ > + .name = id \ > + } Where exactly it is used? What is 'types'? Moreover, it doesn't look very different from EXYNOS850_PIN_BANK_EINTN() -- just because I created EXYNOS850_PIN_BANK_EINTN() exactly from this downstream macro. I was strictly prohibited adding EXYNOS9_* stuff back at the time. But now I guess it should be apparent we are actually dealing with Exynos9 common platform. So I suggest renaming EXYNOS850_PIN_BANK_EINTN() to EXYNOS9_PIN_BANK_EINTN(). > + > +#define EXYNOS9_PIN_BANK_EINTG(pins, reg, id, offs, fltcon_offs) \ > + { \ > + .type = &gs101_bank_type_off, \ > + .pctl_offset = reg, \ > + .nr_pins = pins, \ > + .eint_type = EINT_TYPE_GPIO, \ > + .eint_offset = offs, \ > + .fltcon_type = FLT_DEFAULT, \ > + .fltcon_offset = fltcon_offs, \ > + .name = id \ > + } Ditto. Please add filter fields to EXYNOS850_PIN_BANK_EINTG() instead of adding pretty much the same macro (it is the same, I created EXYNOS850_PIN_BANK_EINTG() from exactly this macro). Also I suggest renaming EXYNOS850_PIN_BANK_EINTG() to EXYNOS9_PIN_BANK_EINTG(), to avoid confusion. If you need any help with reworking Exynos850 pinctrl correspondingly, please let me know. > + > +#define EXYNOS9_PIN_BANK_EINTW(pins, reg, id, offs, fltcon_offs) \ > + { \ > + .type = &gs101_bank_type_alive, \ > + .pctl_offset = reg, \ > + .nr_pins = pins, \ > + .eint_type = EINT_TYPE_WKUP, \ > + .eint_offset = offs, \ > + .fltcon_type = FLT_SELECTABLE, \ > + .fltcon_offset = fltcon_offs, \ > + .name = id \ > + } Ditto. > + > /** > * struct exynos_weint_data: irq specific data for all the wakeup interrupts > * generated by the external wakeup interrupt controller. > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c > index 50c360b4753a..982a5702714c 100644 > --- a/drivers/pinctrl/samsung/pinctrl-samsung.c > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c > @@ -1323,6 +1323,8 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = { > .data = &exynosautov9_of_data }, > { .compatible = "tesla,fsd-pinctrl", > .data = &fsd_of_data }, > + { .compatible = "google,gs101-pinctrl", > + .data = &gs101_of_data }, > #endif > #ifdef CONFIG_PINCTRL_S3C64XX > { .compatible = "samsung,s3c64xx-pinctrl", > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h > index 5fab3885a7d7..f6856290608c 100644 > --- a/drivers/pinctrl/samsung/pinctrl-samsung.h > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h > @@ -373,6 +373,7 @@ extern const struct samsung_pinctrl_of_match_data exynos7885_of_data; > extern const struct samsung_pinctrl_of_match_data exynos850_of_data; > extern const struct samsung_pinctrl_of_match_data exynosautov9_of_data; > extern const struct samsung_pinctrl_of_match_data fsd_of_data; > +extern const struct samsung_pinctrl_of_match_data gs101_of_data; > extern const struct samsung_pinctrl_of_match_data s3c64xx_of_data; > extern const struct samsung_pinctrl_of_match_data s3c2412_of_data; > extern const struct samsung_pinctrl_of_match_data s3c2416_of_data; > -- > 2.43.0.rc2.451.g8631bc7472-goog >
> -----Original Message----- > From: Sam Protsenko <semen.protsenko@linaro.org> > Sent: Saturday, December 2, 2023 6:10 AM > To: Peter Griffin <peter.griffin@linaro.org> > Cc: robh+dt@kernel.org; krzysztof.kozlowski+dt@linaro.org; > mturquette@baylibre.com; conor+dt@kernel.org; sboyd@kernel.org; > tomasz.figa@gmail.com; s.nawrocki@samsung.com; linus.walleij@linaro.org; > wim@linux-watchdog.org; linux@roeck-us.net; catalin.marinas@arm.com; > will@kernel.org; arnd@arndb.de; olof@lixom.net; > gregkh@linuxfoundation.org; jirislaby@kernel.org; > cw00.choi@samsung.com; alim.akhtar@samsung.com; > tudor.ambarus@linaro.org; andre.draszik@linaro.org; > saravanak@google.com; willmcvicker@google.com; soc@kernel.org; > devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- > samsung-soc@vger.kernel.org; linux-clk@vger.kernel.org; linux- > gpio@vger.kernel.org; linux-watchdog@vger.kernel.org; kernel- > team@android.com; linux-serial@vger.kernel.org > Subject: Re: [PATCH v5 14/20] pinctrl: samsung: Add gs101 SoC pinctrl > configuration > > On Fri, Dec 1, 2023 at 10:11 AM Peter Griffin <peter.griffin@linaro.org> > wrote: > > > > Add support for the pin-controller found on the gs101 SoC used in > > Pixel 6 phones. > > > > Signed-off-by: Peter Griffin <peter.griffin@linaro.org> > > --- > > .../pinctrl/samsung/pinctrl-exynos-arm64.c | 159 ++++++++++++++++++ > > drivers/pinctrl/samsung/pinctrl-exynos.c | 2 + > > drivers/pinctrl/samsung/pinctrl-exynos.h | 34 ++++ > > drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + > > drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + > > 5 files changed, 198 insertions(+) > > > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > index cb965cf93705..e1a0668ecb16 100644 > > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data > fsd_of_data __initconst = { > > .ctrl = fsd_pin_ctrl, > > .num_ctrl = ARRAY_SIZE(fsd_pin_ctrl), > > }; > > + > > +/* > > + * bank type for non-alive type > > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit > > +field: 4) > > + * (CONPDN bit field: 2, PUDPDN bit field: 4) */ static struct > > +samsung_pin_bank_type gs101_bank_type_off = { > > + .fld_width = { 4, 1, 4, 4, 2, 4, }, > > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, }; > > This is just the same as exynos850_bank_type_off (100% duplication). > Here is what I suggest. Now that it's obvious there is some common platform > for moder Exynos SoCs, and it's probably Exynos9, I'd suggest next course of > action (if maintainers agree): > 1. Remove this one > 2. Rename exynos850_bank_type_off to exynos9_bank_type_off > 3. Use it for both gs101 and exynos850 > > Does it make sense? > My opinion is to reuse exynos850 for gs101 (wherever applicable), same philosophy was historically followed in this file. That way (using exynos850 for gs101) things will be simple. Adding exynos9_* is not adding any benefit, rather it create confusion. > > + > > +/* > > + * bank type for alive type > > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit > > +field: 4) */ static const struct samsung_pin_bank_type > > +gs101_bank_type_alive = { > > + .fld_width = { 4, 1, 4, 4, }, > > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, }; [...]
On Fri, Dec 1, 2023 at 7:37 PM Alim Akhtar <alim.akhtar@samsung.com> wrote: > > > > > -----Original Message----- > > From: Sam Protsenko <semen.protsenko@linaro.org> > > Sent: Saturday, December 2, 2023 6:10 AM > > To: Peter Griffin <peter.griffin@linaro.org> > > Cc: robh+dt@kernel.org; krzysztof.kozlowski+dt@linaro.org; > > mturquette@baylibre.com; conor+dt@kernel.org; sboyd@kernel.org; > > tomasz.figa@gmail.com; s.nawrocki@samsung.com; linus.walleij@linaro.org; > > wim@linux-watchdog.org; linux@roeck-us.net; catalin.marinas@arm.com; > > will@kernel.org; arnd@arndb.de; olof@lixom.net; > > gregkh@linuxfoundation.org; jirislaby@kernel.org; > > cw00.choi@samsung.com; alim.akhtar@samsung.com; > > tudor.ambarus@linaro.org; andre.draszik@linaro.org; > > saravanak@google.com; willmcvicker@google.com; soc@kernel.org; > > devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- > > samsung-soc@vger.kernel.org; linux-clk@vger.kernel.org; linux- > > gpio@vger.kernel.org; linux-watchdog@vger.kernel.org; kernel- > > team@android.com; linux-serial@vger.kernel.org > > Subject: Re: [PATCH v5 14/20] pinctrl: samsung: Add gs101 SoC pinctrl > > configuration > > > > On Fri, Dec 1, 2023 at 10:11 AM Peter Griffin <peter.griffin@linaro.org> > > wrote: > > > > > > Add support for the pin-controller found on the gs101 SoC used in > > > Pixel 6 phones. > > > > > > Signed-off-by: Peter Griffin <peter.griffin@linaro.org> > > > --- > > > .../pinctrl/samsung/pinctrl-exynos-arm64.c | 159 ++++++++++++++++++ > > > drivers/pinctrl/samsung/pinctrl-exynos.c | 2 + > > > drivers/pinctrl/samsung/pinctrl-exynos.h | 34 ++++ > > > drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + > > > drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + > > > 5 files changed, 198 insertions(+) > > > > > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > > b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > > index cb965cf93705..e1a0668ecb16 100644 > > > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > > @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data > > fsd_of_data __initconst = { > > > .ctrl = fsd_pin_ctrl, > > > .num_ctrl = ARRAY_SIZE(fsd_pin_ctrl), > > > }; > > > + > > > +/* > > > + * bank type for non-alive type > > > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit > > > +field: 4) > > > + * (CONPDN bit field: 2, PUDPDN bit field: 4) */ static struct > > > +samsung_pin_bank_type gs101_bank_type_off = { > > > + .fld_width = { 4, 1, 4, 4, 2, 4, }, > > > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, }; > > > > This is just the same as exynos850_bank_type_off (100% duplication). > > Here is what I suggest. Now that it's obvious there is some common platform > > for moder Exynos SoCs, and it's probably Exynos9, I'd suggest next course of > > action (if maintainers agree): > > 1. Remove this one > > 2. Rename exynos850_bank_type_off to exynos9_bank_type_off > > 3. Use it for both gs101 and exynos850 > > > > Does it make sense? > > > My opinion is to reuse exynos850 for gs101 (wherever applicable), same philosophy was historically followed in this file. > That way (using exynos850 for gs101) things will be simple. > Adding exynos9_* is not adding any benefit, rather it create confusion. > Yes. But why not also rename exynos850_* to exynos9_*? I've a feeling that a lot of modern Exynos SoCs have the same pin bank configuration. Wouldn't it be better to use exynos9_ prefix for all such SoCs than exynos850_*? Because Exynos9 is a family, but Exynos850 is a particular SoC from that family. > > > + > > > +/* > > > + * bank type for alive type > > > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit > > > +field: 4) */ static const struct samsung_pin_bank_type > > > +gs101_bank_type_alive = { > > > + .fld_width = { 4, 1, 4, 4, }, > > > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, }; > [...] > >
Hi Sam, Thanks for the review. On Sat, 2 Dec 2023 at 00:40, Sam Protsenko <semen.protsenko@linaro.org> wrote: > > On Fri, Dec 1, 2023 at 10:11 AM Peter Griffin <peter.griffin@linaro.org> wrote: > > > > Add support for the pin-controller found on the gs101 SoC used in > > Pixel 6 phones. > > > > Signed-off-by: Peter Griffin <peter.griffin@linaro.org> > > --- > > .../pinctrl/samsung/pinctrl-exynos-arm64.c | 159 ++++++++++++++++++ > > drivers/pinctrl/samsung/pinctrl-exynos.c | 2 + > > drivers/pinctrl/samsung/pinctrl-exynos.h | 34 ++++ > > drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + > > drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + > > 5 files changed, 198 insertions(+) > > > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > index cb965cf93705..e1a0668ecb16 100644 > > --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > > @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data fsd_of_data __initconst = { > > .ctrl = fsd_pin_ctrl, > > .num_ctrl = ARRAY_SIZE(fsd_pin_ctrl), > > }; > > + > > +/* > > + * bank type for non-alive type > > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit field: 4) > > + * (CONPDN bit field: 2, PUDPDN bit field: 4) > > + */ > > +static struct samsung_pin_bank_type gs101_bank_type_off = { > > + .fld_width = { 4, 1, 4, 4, 2, 4, }, > > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, > > +}; > > This is just the same as exynos850_bank_type_off (100% duplication). Ah nice, I hadn't spotted that these structs matched exynos850. > Here is what I suggest. Now that it's obvious there is some common > platform for moder Exynos SoCs, and it's probably Exynos9, I'd suggest > next course of action (if maintainers agree): > 1. Remove this one > 2. Rename exynos850_bank_type_off to exynos9_bank_type_off > 3. Use it for both gs101 and exynos850 > > Does it make sense? Yes, sounds like a good plan to me. I just checked downstream and they were called bank_type_6 and bank_type_7 originally. @Krzysztof - are you OK with the proposed generic name above (exynos9_bank_type_off?) to be used by both exynos850 and gs101 (and also future Tensor exynos based SoCs)? > > > + > > +/* > > + * bank type for alive type > > + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit field: 4) > > + */ > > +static const struct samsung_pin_bank_type gs101_bank_type_alive = { > > + .fld_width = { 4, 1, 4, 4, }, > > + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, > > +}; > > Ditto, it's a duplication of exynos850_bank_type_alive . > > > + > > +/* pin banks of gs101 pin-controller (ALIVE) */ > > +static const struct samsung_pin_bank_data gs101_pin_alive[] = { > > + EXYNOS9_PIN_BANK_EINTW(8, 0x0, "gpa0", 0x00, 0x00), > > + EXYNOS9_PIN_BANK_EINTW(7, 0x20, "gpa1", 0x04, 0x08), > > + EXYNOS9_PIN_BANK_EINTW(5, 0x40, "gpa2", 0x08, 0x10), > > + EXYNOS9_PIN_BANK_EINTW(4, 0x60, "gpa3", 0x0c, 0x18), > > + EXYNOS9_PIN_BANK_EINTW(4, 0x80, "gpa4", 0x10, 0x1c), > > + EXYNOS9_PIN_BANK_EINTW(7, 0xa0, "gpa5", 0x14, 0x20), > > + EXYNOS9_PIN_BANK_EINTW(8, 0xc0, "gpa9", 0x18, 0x28), > > + EXYNOS9_PIN_BANK_EINTW(2, 0xe0, "gpa10", 0x1c, 0x30), > > +}; > > + > > +/* pin banks of gs101 pin-controller (FAR_ALIVE) */ > > +static const struct samsung_pin_bank_data gs101_pin_far_alive[] = { > > + EXYNOS9_PIN_BANK_EINTW(8, 0x0, "gpa6", 0x00, 0x00), > > + EXYNOS9_PIN_BANK_EINTW(4, 0x20, "gpa7", 0x04, 0x08), > > + EXYNOS9_PIN_BANK_EINTW(8, 0x40, "gpa8", 0x08, 0x0c), > > + EXYNOS9_PIN_BANK_EINTW(2, 0x60, "gpa11", 0x0c, 0x14), > > +}; > > + > > +/* pin banks of gs101 pin-controller (GSACORE) */ > > +static const struct samsung_pin_bank_data gs101_pin_gsacore[] = { > > + EXYNOS9_PIN_BANK_EINTG(2, 0x0, "gps0", 0x00, 0x00), > > + EXYNOS9_PIN_BANK_EINTG(8, 0x20, "gps1", 0x04, 0x04), > > + EXYNOS9_PIN_BANK_EINTG(3, 0x40, "gps2", 0x08, 0x0c), > > +}; > > + > > +/* pin banks of gs101 pin-controller (GSACTRL) */ > > +static const struct samsung_pin_bank_data gs101_pin_gsactrl[] = { > > + EXYNOS9_PIN_BANK_EINTW(6, 0x0, "gps3", 0x00, 0x00), > > +}; > > + > > +/* pin banks of gs101 pin-controller (PERIC0) */ > > +static const struct samsung_pin_bank_data gs101_pin_peric0[] = { > > + EXYNOS9_PIN_BANK_EINTG(5, 0x0, "gpp0", 0x00, 0x00), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x20, "gpp1", 0x04, 0x08), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x40, "gpp2", 0x08, 0x0c), > > + EXYNOS9_PIN_BANK_EINTG(2, 0x60, "gpp3", 0x0c, 0x10), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x80, "gpp4", 0x10, 0x14), > > + EXYNOS9_PIN_BANK_EINTG(2, 0xa0, "gpp5", 0x14, 0x18), > > + EXYNOS9_PIN_BANK_EINTG(4, 0xc0, "gpp6", 0x18, 0x1c), > > + EXYNOS9_PIN_BANK_EINTG(2, 0xe0, "gpp7", 0x1c, 0x20), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x100, "gpp8", 0x20, 0x24), > > + EXYNOS9_PIN_BANK_EINTG(2, 0x120, "gpp9", 0x24, 0x28), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x140, "gpp10", 0x28, 0x2c), > > + EXYNOS9_PIN_BANK_EINTG(2, 0x160, "gpp11", 0x2c, 0x30), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x180, "gpp12", 0x30, 0x34), > > + EXYNOS9_PIN_BANK_EINTG(2, 0x1a0, "gpp13", 0x34, 0x38), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x1c0, "gpp14", 0x38, 0x3c), > > + EXYNOS9_PIN_BANK_EINTG(2, 0x1e0, "gpp15", 0x3c, 0x40), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x200, "gpp16", 0x40, 0x44), > > + EXYNOS9_PIN_BANK_EINTG(2, 0x220, "gpp17", 0x44, 0x48), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x240, "gpp18", 0x48, 0x4c), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x260, "gpp19", 0x4c, 0x50), > > +}; > > + > > +/* pin banks of gs101 pin-controller (PERIC1) */ > > +static const struct samsung_pin_bank_data gs101_pin_peric1[] = { > > + EXYNOS9_PIN_BANK_EINTG(8, 0x0, "gpp20", 0x00, 0x00), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x20, "gpp21", 0x04, 0x08), > > + EXYNOS9_PIN_BANK_EINTG(2, 0x40, "gpp22", 0x08, 0x0c), > > + EXYNOS9_PIN_BANK_EINTG(8, 0x60, "gpp23", 0x0c, 0x10), > > + EXYNOS9_PIN_BANK_EINTG(4, 0x80, "gpp24", 0x10, 0x18), > > + EXYNOS9_PIN_BANK_EINTG(4, 0xa0, "gpp25", 0x14, 0x1c), > > + EXYNOS9_PIN_BANK_EINTG(5, 0xc0, "gpp26", 0x18, 0x20), > > + EXYNOS9_PIN_BANK_EINTG(4, 0xe0, "gpp27", 0x1c, 0x28), > > +}; > > + > > +/* pin banks of gs101 pin-controller (HSI1) */ > > +static const struct samsung_pin_bank_data gs101_pin_hsi1[] = { > > + EXYNOS9_PIN_BANK_EINTG(6, 0x0, "gph0", 0x00, 0x00), > > + EXYNOS9_PIN_BANK_EINTG(7, 0x20, "gph1", 0x04, 0x08), > > +}; > > + > > +/* pin banks of gs101 pin-controller (HSI2) */ > > +static const struct samsung_pin_bank_data gs101_pin_hsi2[] = { > > + EXYNOS9_PIN_BANK_EINTG(6, 0x0, "gph2", 0x00, 0x00), > > + EXYNOS9_PIN_BANK_EINTG(2, 0x20, "gph3", 0x04, 0x08), > > + EXYNOS9_PIN_BANK_EINTG(6, 0x40, "gph4", 0x08, 0x0c), > > +}; > > + > > +static const struct samsung_pin_ctrl gs101_pin_ctrl[] __initconst = { > > + { > > + /* pin banks of gs101 pin-controller (ALIVE) */ > > + .pin_banks = gs101_pin_alive, > > + .nr_banks = ARRAY_SIZE(gs101_pin_alive), > > + .eint_wkup_init = exynos_eint_wkup_init, > > + .suspend = exynos_pinctrl_suspend, > > + .resume = exynos_pinctrl_resume, > > + }, { > > + /* pin banks of gs101 pin-controller (FAR_ALIVE) */ > > + .pin_banks = gs101_pin_far_alive, > > + .nr_banks = ARRAY_SIZE(gs101_pin_far_alive), > > + .eint_wkup_init = exynos_eint_wkup_init, > > + .suspend = exynos_pinctrl_suspend, > > + .resume = exynos_pinctrl_resume, > > + }, { > > + /* pin banks of gs101 pin-controller (GSACORE) */ > > + .pin_banks = gs101_pin_gsacore, > > + .nr_banks = ARRAY_SIZE(gs101_pin_gsacore), > > + }, { > > + /* pin banks of gs101 pin-controller (GSACTRL) */ > > + .pin_banks = gs101_pin_gsactrl, > > + .nr_banks = ARRAY_SIZE(gs101_pin_gsactrl), > > + }, { > > + /* pin banks of gs101 pin-controller (PERIC0) */ > > + .pin_banks = gs101_pin_peric0, > > + .nr_banks = ARRAY_SIZE(gs101_pin_peric0), > > + .eint_gpio_init = exynos_eint_gpio_init, > > + .suspend = exynos_pinctrl_suspend, > > + .resume = exynos_pinctrl_resume, > > + }, { > > + /* pin banks of gs101 pin-controller (PERIC1) */ > > + .pin_banks = gs101_pin_peric1, > > + .nr_banks = ARRAY_SIZE(gs101_pin_peric1), > > + .eint_gpio_init = exynos_eint_gpio_init, > > + .suspend = exynos_pinctrl_suspend, > > + .resume = exynos_pinctrl_resume, > > + }, { > > + /* pin banks of gs101 pin-controller (HSI1) */ > > + .pin_banks = gs101_pin_hsi1, > > + .nr_banks = ARRAY_SIZE(gs101_pin_hsi1), > > + .eint_gpio_init = exynos_eint_gpio_init, > > + .suspend = exynos_pinctrl_suspend, > > + .resume = exynos_pinctrl_resume, > > + }, { > > + /* pin banks of gs101 pin-controller (HSI2) */ > > + .pin_banks = gs101_pin_hsi2, > > + .nr_banks = ARRAY_SIZE(gs101_pin_hsi2), > > + .eint_gpio_init = exynos_eint_gpio_init, > > + .suspend = exynos_pinctrl_suspend, > > + .resume = exynos_pinctrl_resume, > > + }, > > +}; > > + > > +const struct samsung_pinctrl_of_match_data gs101_of_data __initconst = { > > + .ctrl = gs101_pin_ctrl, > > + .num_ctrl = ARRAY_SIZE(gs101_pin_ctrl), > > +}; > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c > > index 56fc11a1fe2f..75b9cf72ce73 100644 > > --- a/drivers/pinctrl/samsung/pinctrl-exynos.c > > +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c > > @@ -537,6 +537,8 @@ static const struct of_device_id exynos_wkup_irq_ids[] = { > > .data = &exynos7_wkup_irq_chip }, > > { .compatible = "samsung,exynosautov9-wakeup-eint", > > .data = &exynos7_wkup_irq_chip }, > > + { .compatible = "google,gs101-wakeup-eint", > > + .data = &exynos7_wkup_irq_chip }, > > { } > > }; > > > > diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h > > index e2799ff1b5e9..1ffc90db079d 100644 > > --- a/drivers/pinctrl/samsung/pinctrl-exynos.h > > +++ b/drivers/pinctrl/samsung/pinctrl-exynos.h > > @@ -147,6 +147,40 @@ > > .name = id \ > > } > > > > +#define EXYNOS9_PIN_BANK_EINTN(types, pins, reg, id) \ > > + { \ > > + .type = &types, \ > > + .pctl_offset = reg, \ > > + .nr_pins = pins, \ > > + .eint_type = EINT_TYPE_NONE, \ > > + .fltcon_type = FLT_DEFAULT \ > > + .name = id \ > > + } > > Where exactly it is used? What is 'types'? EXYNOS9_PIN_BANK_EINTN macro can be dropped completely for gs101 as it isn't used anywhere. I checked downstream code and it is declared and not used there as well. >Moreover, it doesn't look > very different from EXYNOS850_PIN_BANK_EINTN() -- just because I > created EXYNOS850_PIN_BANK_EINTN() exactly from this downstream macro. > I was strictly prohibited adding EXYNOS9_* stuff back at the time. But > now I guess it should be apparent we are actually dealing with Exynos9 > common platform. So I suggest renaming EXYNOS850_PIN_BANK_EINTN() to > EXYNOS9_PIN_BANK_EINTN(). > > > + > > +#define EXYNOS9_PIN_BANK_EINTG(pins, reg, id, offs, fltcon_offs) \ > > + { \ > > + .type = &gs101_bank_type_off, \ > > + .pctl_offset = reg, \ > > + .nr_pins = pins, \ > > + .eint_type = EINT_TYPE_GPIO, \ > > + .eint_offset = offs, \ > > + .fltcon_type = FLT_DEFAULT, \ > > + .fltcon_offset = fltcon_offs, \ > > + .name = id \ > > + } > > Ditto. Please add filter fields to EXYNOS850_PIN_BANK_EINTG() instead > of adding pretty much the same macro (it is the same, I created > EXYNOS850_PIN_BANK_EINTG() from exactly this macro). Also I suggest > renaming EXYNOS850_PIN_BANK_EINTG() to EXYNOS9_PIN_BANK_EINTG(), to > avoid confusion. If you need any help with reworking Exynos850 pinctrl > correspondingly, please let me know. The only issue for me migrating Exynos850 to EXYNOS9_PIN_BANK_EINTG is knowing what the fltcon_offset is. Can you provide the fltcon_offset offsets for the relevant Exynos850 banks and help test? Thanks, Peter. > > > + > > +#define EXYNOS9_PIN_BANK_EINTW(pins, reg, id, offs, fltcon_offs) \ > > + { \ > > + .type = &gs101_bank_type_alive, \ > > + .pctl_offset = reg, \ > > + .nr_pins = pins, \ > > + .eint_type = EINT_TYPE_WKUP, \ > > + .eint_offset = offs, \ > > + .fltcon_type = FLT_SELECTABLE, \ > > + .fltcon_offset = fltcon_offs, \ > > + .name = id \ > > + } > > Ditto. > > > + > > /** > > * struct exynos_weint_data: irq specific data for all the wakeup interrupts > > * generated by the external wakeup interrupt controller. > > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c > > index 50c360b4753a..982a5702714c 100644 > > --- a/drivers/pinctrl/samsung/pinctrl-samsung.c > > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c > > @@ -1323,6 +1323,8 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = { > > .data = &exynosautov9_of_data }, > > { .compatible = "tesla,fsd-pinctrl", > > .data = &fsd_of_data }, > > + { .compatible = "google,gs101-pinctrl", > > + .data = &gs101_of_data }, > > #endif > > #ifdef CONFIG_PINCTRL_S3C64XX > > { .compatible = "samsung,s3c64xx-pinctrl", > > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h > > index 5fab3885a7d7..f6856290608c 100644 > > --- a/drivers/pinctrl/samsung/pinctrl-samsung.h > > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h > > @@ -373,6 +373,7 @@ extern const struct samsung_pinctrl_of_match_data exynos7885_of_data; > > extern const struct samsung_pinctrl_of_match_data exynos850_of_data; > > extern const struct samsung_pinctrl_of_match_data exynosautov9_of_data; > > extern const struct samsung_pinctrl_of_match_data fsd_of_data; > > +extern const struct samsung_pinctrl_of_match_data gs101_of_data; > > extern const struct samsung_pinctrl_of_match_data s3c64xx_of_data; > > extern const struct samsung_pinctrl_of_match_data s3c2412_of_data; > > extern const struct samsung_pinctrl_of_match_data s3c2416_of_data; > > -- > > 2.43.0.rc2.451.g8631bc7472-goog > >
On 02/12/2023 02:36, Alim Akhtar wrote: > > >> -----Original Message----- >> From: Sam Protsenko <semen.protsenko@linaro.org> >> Sent: Saturday, December 2, 2023 6:10 AM >> To: Peter Griffin <peter.griffin@linaro.org> >> Cc: robh+dt@kernel.org; krzysztof.kozlowski+dt@linaro.org; >> mturquette@baylibre.com; conor+dt@kernel.org; sboyd@kernel.org; >> tomasz.figa@gmail.com; s.nawrocki@samsung.com; linus.walleij@linaro.org; >> wim@linux-watchdog.org; linux@roeck-us.net; catalin.marinas@arm.com; >> will@kernel.org; arnd@arndb.de; olof@lixom.net; >> gregkh@linuxfoundation.org; jirislaby@kernel.org; >> cw00.choi@samsung.com; alim.akhtar@samsung.com; >> tudor.ambarus@linaro.org; andre.draszik@linaro.org; >> saravanak@google.com; willmcvicker@google.com; soc@kernel.org; >> devicetree@vger.kernel.org; linux-arm-kernel@lists.infradead.org; linux- >> samsung-soc@vger.kernel.org; linux-clk@vger.kernel.org; linux- >> gpio@vger.kernel.org; linux-watchdog@vger.kernel.org; kernel- >> team@android.com; linux-serial@vger.kernel.org >> Subject: Re: [PATCH v5 14/20] pinctrl: samsung: Add gs101 SoC pinctrl >> configuration >> >> On Fri, Dec 1, 2023 at 10:11 AM Peter Griffin <peter.griffin@linaro.org> >> wrote: >>> >>> Add support for the pin-controller found on the gs101 SoC used in >>> Pixel 6 phones. >>> >>> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> >>> --- >>> .../pinctrl/samsung/pinctrl-exynos-arm64.c | 159 ++++++++++++++++++ >>> drivers/pinctrl/samsung/pinctrl-exynos.c | 2 + >>> drivers/pinctrl/samsung/pinctrl-exynos.h | 34 ++++ >>> drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + >>> drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + >>> 5 files changed, 198 insertions(+) >>> >>> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >>> b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >>> index cb965cf93705..e1a0668ecb16 100644 >>> --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >>> +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c >>> @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data >> fsd_of_data __initconst = { >>> .ctrl = fsd_pin_ctrl, >>> .num_ctrl = ARRAY_SIZE(fsd_pin_ctrl), >>> }; >>> + >>> +/* >>> + * bank type for non-alive type >>> + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit >>> +field: 4) >>> + * (CONPDN bit field: 2, PUDPDN bit field: 4) */ static struct >>> +samsung_pin_bank_type gs101_bank_type_off = { >>> + .fld_width = { 4, 1, 4, 4, 2, 4, }, >>> + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, }; >> >> This is just the same as exynos850_bank_type_off (100% duplication). >> Here is what I suggest. Now that it's obvious there is some common platform >> for moder Exynos SoCs, and it's probably Exynos9, I'd suggest next course of >> action (if maintainers agree): >> 1. Remove this one >> 2. Rename exynos850_bank_type_off to exynos9_bank_type_off >> 3. Use it for both gs101 and exynos850 >> >> Does it make sense? >> > My opinion is to reuse exynos850 for gs101 (wherever applicable), same philosophy was historically followed in this file. > That way (using exynos850 for gs101) things will be simple. > Adding exynos9_* is not adding any benefit, rather it create confusion. I don't see much value in renaming exynos850 bank type to exynos9 considering: 1. We don't really know the bank types for all of Exynos9xxx SoCs, 2. Exynos7885 also uses Exynos850 bank types. Exynos7885 was much earlier than Exynos9xxx family. Best regards, Krzysztof
Hi Krzysztof / Sam, On Wed, 6 Dec 2023 at 11:38, Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> wrote: > > On 02/12/2023 02:36, Alim Akhtar wrote: > > > >> > >> On Fri, Dec 1, 2023 at 10:11 AM Peter Griffin <peter.griffin@linaro.org> > >> wrote: > >>> > >>> Add support for the pin-controller found on the gs101 SoC used in > >>> Pixel 6 phones. > >>> > >>> Signed-off-by: Peter Griffin <peter.griffin@linaro.org> > >>> --- > >>> .../pinctrl/samsung/pinctrl-exynos-arm64.c | 159 ++++++++++++++++++ > >>> drivers/pinctrl/samsung/pinctrl-exynos.c | 2 + > >>> drivers/pinctrl/samsung/pinctrl-exynos.h | 34 ++++ > >>> drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + > >>> drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + > >>> 5 files changed, 198 insertions(+) > >>> > >>> diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > >>> b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > >>> index cb965cf93705..e1a0668ecb16 100644 > >>> --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > >>> +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c > >>> @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data > >> fsd_of_data __initconst = { > >>> .ctrl = fsd_pin_ctrl, > >>> .num_ctrl = ARRAY_SIZE(fsd_pin_ctrl), > >>> }; > >>> + > >>> +/* > >>> + * bank type for non-alive type > >>> + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit > >>> +field: 4) > >>> + * (CONPDN bit field: 2, PUDPDN bit field: 4) */ static struct > >>> +samsung_pin_bank_type gs101_bank_type_off = { > >>> + .fld_width = { 4, 1, 4, 4, 2, 4, }, > >>> + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, }; > >> > >> This is just the same as exynos850_bank_type_off (100% duplication). > >> Here is what I suggest. Now that it's obvious there is some common platform > >> for moder Exynos SoCs, and it's probably Exynos9, I'd suggest next course of > >> action (if maintainers agree): > >> 1. Remove this one > >> 2. Rename exynos850_bank_type_off to exynos9_bank_type_off > >> 3. Use it for both gs101 and exynos850 > >> > >> Does it make sense? > >> > > My opinion is to reuse exynos850 for gs101 (wherever applicable), same philosophy was historically followed in this file. > > That way (using exynos850 for gs101) things will be simple. > > Adding exynos9_* is not adding any benefit, rather it create confusion. > > I don't see much value in renaming exynos850 bank type to exynos9 > considering: > 1. We don't really know the bank types for all of Exynos9xxx SoCs, > 2. Exynos7885 also uses Exynos850 bank types. Exynos7885 was much > earlier than Exynos9xxx family. Thanks Alim and Krzysztof for your input. Exynos7885 (Exynos 8 family) using Exynos850 bank types looks like a mistake to me. I found some downstream code for 7885, and it doesn't look like selecting a filter was supported downstream [1] [2]. As Sam confirmed this hardware is present on e850 downstream, so 7885 and e850 have different hardware at least for these banks. As the EXYNOS850_PIN_BANK_EINTW macro is being used by Exynos850, exynosautov9 and exynos7885 using a generic macro with gs101 doesn't look possible (I have no way to find out these filter register offsets, or if those platforms actually have these registers). Therefore I propose: 1. For bank types that match exactly use exynos850 versions 2. For bank types which have fltcon_offset we add a new macro EXYNOS9_PIN_BANK_EINTW like it exists in this series or GS101_PIN_BANK_EINTW if people prefer that That still leaves us in the rather unfortunate position that if Exynos850 wants selectable filter support then it wouldn't be using the EXYNOS850_PIN_BANK_EINTW macro. But I suggest we cross that bridge if/when Sam decides to support selectable filters on e850. We could do some sort of macro renaming, but what we rename it to though I have no idea EXYNOS7885_blah or EXYNOSAUTOV9_blah. @Chanho do you know if ExynosAutov9 supports selectable filters on alive banks? regards, Peter [1] https://github.com/samsungexynos7885/android_kernel_samsung_universal7885/blob/android-9.0/drivers/pinctrl/samsung/pinctrl-exynos.c#L1696 [2] https://github.com/samsungexynos7885/android_kernel_samsung_universal7885/blob/android-9.0/drivers/pinctrl/samsung/pinctrl-exynos.h#L108
diff --git a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c index cb965cf93705..e1a0668ecb16 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos-arm64.c @@ -796,3 +796,162 @@ const struct samsung_pinctrl_of_match_data fsd_of_data __initconst = { .ctrl = fsd_pin_ctrl, .num_ctrl = ARRAY_SIZE(fsd_pin_ctrl), }; + +/* + * bank type for non-alive type + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit field: 4) + * (CONPDN bit field: 2, PUDPDN bit field: 4) + */ +static struct samsung_pin_bank_type gs101_bank_type_off = { + .fld_width = { 4, 1, 4, 4, 2, 4, }, + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, }, +}; + +/* + * bank type for alive type + * (CON bit field: 4, DAT bit field: 1, PUD bit field: 4, DRV bit field: 4) + */ +static const struct samsung_pin_bank_type gs101_bank_type_alive = { + .fld_width = { 4, 1, 4, 4, }, + .reg_offset = { 0x00, 0x04, 0x08, 0x0c, }, +}; + +/* pin banks of gs101 pin-controller (ALIVE) */ +static const struct samsung_pin_bank_data gs101_pin_alive[] = { + EXYNOS9_PIN_BANK_EINTW(8, 0x0, "gpa0", 0x00, 0x00), + EXYNOS9_PIN_BANK_EINTW(7, 0x20, "gpa1", 0x04, 0x08), + EXYNOS9_PIN_BANK_EINTW(5, 0x40, "gpa2", 0x08, 0x10), + EXYNOS9_PIN_BANK_EINTW(4, 0x60, "gpa3", 0x0c, 0x18), + EXYNOS9_PIN_BANK_EINTW(4, 0x80, "gpa4", 0x10, 0x1c), + EXYNOS9_PIN_BANK_EINTW(7, 0xa0, "gpa5", 0x14, 0x20), + EXYNOS9_PIN_BANK_EINTW(8, 0xc0, "gpa9", 0x18, 0x28), + EXYNOS9_PIN_BANK_EINTW(2, 0xe0, "gpa10", 0x1c, 0x30), +}; + +/* pin banks of gs101 pin-controller (FAR_ALIVE) */ +static const struct samsung_pin_bank_data gs101_pin_far_alive[] = { + EXYNOS9_PIN_BANK_EINTW(8, 0x0, "gpa6", 0x00, 0x00), + EXYNOS9_PIN_BANK_EINTW(4, 0x20, "gpa7", 0x04, 0x08), + EXYNOS9_PIN_BANK_EINTW(8, 0x40, "gpa8", 0x08, 0x0c), + EXYNOS9_PIN_BANK_EINTW(2, 0x60, "gpa11", 0x0c, 0x14), +}; + +/* pin banks of gs101 pin-controller (GSACORE) */ +static const struct samsung_pin_bank_data gs101_pin_gsacore[] = { + EXYNOS9_PIN_BANK_EINTG(2, 0x0, "gps0", 0x00, 0x00), + EXYNOS9_PIN_BANK_EINTG(8, 0x20, "gps1", 0x04, 0x04), + EXYNOS9_PIN_BANK_EINTG(3, 0x40, "gps2", 0x08, 0x0c), +}; + +/* pin banks of gs101 pin-controller (GSACTRL) */ +static const struct samsung_pin_bank_data gs101_pin_gsactrl[] = { + EXYNOS9_PIN_BANK_EINTW(6, 0x0, "gps3", 0x00, 0x00), +}; + +/* pin banks of gs101 pin-controller (PERIC0) */ +static const struct samsung_pin_bank_data gs101_pin_peric0[] = { + EXYNOS9_PIN_BANK_EINTG(5, 0x0, "gpp0", 0x00, 0x00), + EXYNOS9_PIN_BANK_EINTG(4, 0x20, "gpp1", 0x04, 0x08), + EXYNOS9_PIN_BANK_EINTG(4, 0x40, "gpp2", 0x08, 0x0c), + EXYNOS9_PIN_BANK_EINTG(2, 0x60, "gpp3", 0x0c, 0x10), + EXYNOS9_PIN_BANK_EINTG(4, 0x80, "gpp4", 0x10, 0x14), + EXYNOS9_PIN_BANK_EINTG(2, 0xa0, "gpp5", 0x14, 0x18), + EXYNOS9_PIN_BANK_EINTG(4, 0xc0, "gpp6", 0x18, 0x1c), + EXYNOS9_PIN_BANK_EINTG(2, 0xe0, "gpp7", 0x1c, 0x20), + EXYNOS9_PIN_BANK_EINTG(4, 0x100, "gpp8", 0x20, 0x24), + EXYNOS9_PIN_BANK_EINTG(2, 0x120, "gpp9", 0x24, 0x28), + EXYNOS9_PIN_BANK_EINTG(4, 0x140, "gpp10", 0x28, 0x2c), + EXYNOS9_PIN_BANK_EINTG(2, 0x160, "gpp11", 0x2c, 0x30), + EXYNOS9_PIN_BANK_EINTG(4, 0x180, "gpp12", 0x30, 0x34), + EXYNOS9_PIN_BANK_EINTG(2, 0x1a0, "gpp13", 0x34, 0x38), + EXYNOS9_PIN_BANK_EINTG(4, 0x1c0, "gpp14", 0x38, 0x3c), + EXYNOS9_PIN_BANK_EINTG(2, 0x1e0, "gpp15", 0x3c, 0x40), + EXYNOS9_PIN_BANK_EINTG(4, 0x200, "gpp16", 0x40, 0x44), + EXYNOS9_PIN_BANK_EINTG(2, 0x220, "gpp17", 0x44, 0x48), + EXYNOS9_PIN_BANK_EINTG(4, 0x240, "gpp18", 0x48, 0x4c), + EXYNOS9_PIN_BANK_EINTG(4, 0x260, "gpp19", 0x4c, 0x50), +}; + +/* pin banks of gs101 pin-controller (PERIC1) */ +static const struct samsung_pin_bank_data gs101_pin_peric1[] = { + EXYNOS9_PIN_BANK_EINTG(8, 0x0, "gpp20", 0x00, 0x00), + EXYNOS9_PIN_BANK_EINTG(4, 0x20, "gpp21", 0x04, 0x08), + EXYNOS9_PIN_BANK_EINTG(2, 0x40, "gpp22", 0x08, 0x0c), + EXYNOS9_PIN_BANK_EINTG(8, 0x60, "gpp23", 0x0c, 0x10), + EXYNOS9_PIN_BANK_EINTG(4, 0x80, "gpp24", 0x10, 0x18), + EXYNOS9_PIN_BANK_EINTG(4, 0xa0, "gpp25", 0x14, 0x1c), + EXYNOS9_PIN_BANK_EINTG(5, 0xc0, "gpp26", 0x18, 0x20), + EXYNOS9_PIN_BANK_EINTG(4, 0xe0, "gpp27", 0x1c, 0x28), +}; + +/* pin banks of gs101 pin-controller (HSI1) */ +static const struct samsung_pin_bank_data gs101_pin_hsi1[] = { + EXYNOS9_PIN_BANK_EINTG(6, 0x0, "gph0", 0x00, 0x00), + EXYNOS9_PIN_BANK_EINTG(7, 0x20, "gph1", 0x04, 0x08), +}; + +/* pin banks of gs101 pin-controller (HSI2) */ +static const struct samsung_pin_bank_data gs101_pin_hsi2[] = { + EXYNOS9_PIN_BANK_EINTG(6, 0x0, "gph2", 0x00, 0x00), + EXYNOS9_PIN_BANK_EINTG(2, 0x20, "gph3", 0x04, 0x08), + EXYNOS9_PIN_BANK_EINTG(6, 0x40, "gph4", 0x08, 0x0c), +}; + +static const struct samsung_pin_ctrl gs101_pin_ctrl[] __initconst = { + { + /* pin banks of gs101 pin-controller (ALIVE) */ + .pin_banks = gs101_pin_alive, + .nr_banks = ARRAY_SIZE(gs101_pin_alive), + .eint_wkup_init = exynos_eint_wkup_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin banks of gs101 pin-controller (FAR_ALIVE) */ + .pin_banks = gs101_pin_far_alive, + .nr_banks = ARRAY_SIZE(gs101_pin_far_alive), + .eint_wkup_init = exynos_eint_wkup_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin banks of gs101 pin-controller (GSACORE) */ + .pin_banks = gs101_pin_gsacore, + .nr_banks = ARRAY_SIZE(gs101_pin_gsacore), + }, { + /* pin banks of gs101 pin-controller (GSACTRL) */ + .pin_banks = gs101_pin_gsactrl, + .nr_banks = ARRAY_SIZE(gs101_pin_gsactrl), + }, { + /* pin banks of gs101 pin-controller (PERIC0) */ + .pin_banks = gs101_pin_peric0, + .nr_banks = ARRAY_SIZE(gs101_pin_peric0), + .eint_gpio_init = exynos_eint_gpio_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin banks of gs101 pin-controller (PERIC1) */ + .pin_banks = gs101_pin_peric1, + .nr_banks = ARRAY_SIZE(gs101_pin_peric1), + .eint_gpio_init = exynos_eint_gpio_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin banks of gs101 pin-controller (HSI1) */ + .pin_banks = gs101_pin_hsi1, + .nr_banks = ARRAY_SIZE(gs101_pin_hsi1), + .eint_gpio_init = exynos_eint_gpio_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, { + /* pin banks of gs101 pin-controller (HSI2) */ + .pin_banks = gs101_pin_hsi2, + .nr_banks = ARRAY_SIZE(gs101_pin_hsi2), + .eint_gpio_init = exynos_eint_gpio_init, + .suspend = exynos_pinctrl_suspend, + .resume = exynos_pinctrl_resume, + }, +}; + +const struct samsung_pinctrl_of_match_data gs101_of_data __initconst = { + .ctrl = gs101_pin_ctrl, + .num_ctrl = ARRAY_SIZE(gs101_pin_ctrl), +}; diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c index 56fc11a1fe2f..75b9cf72ce73 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos.c +++ b/drivers/pinctrl/samsung/pinctrl-exynos.c @@ -537,6 +537,8 @@ static const struct of_device_id exynos_wkup_irq_ids[] = { .data = &exynos7_wkup_irq_chip }, { .compatible = "samsung,exynosautov9-wakeup-eint", .data = &exynos7_wkup_irq_chip }, + { .compatible = "google,gs101-wakeup-eint", + .data = &exynos7_wkup_irq_chip }, { } }; diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.h b/drivers/pinctrl/samsung/pinctrl-exynos.h index e2799ff1b5e9..1ffc90db079d 100644 --- a/drivers/pinctrl/samsung/pinctrl-exynos.h +++ b/drivers/pinctrl/samsung/pinctrl-exynos.h @@ -147,6 +147,40 @@ .name = id \ } +#define EXYNOS9_PIN_BANK_EINTN(types, pins, reg, id) \ + { \ + .type = &types, \ + .pctl_offset = reg, \ + .nr_pins = pins, \ + .eint_type = EINT_TYPE_NONE, \ + .fltcon_type = FLT_DEFAULT \ + .name = id \ + } + +#define EXYNOS9_PIN_BANK_EINTG(pins, reg, id, offs, fltcon_offs) \ + { \ + .type = &gs101_bank_type_off, \ + .pctl_offset = reg, \ + .nr_pins = pins, \ + .eint_type = EINT_TYPE_GPIO, \ + .eint_offset = offs, \ + .fltcon_type = FLT_DEFAULT, \ + .fltcon_offset = fltcon_offs, \ + .name = id \ + } + +#define EXYNOS9_PIN_BANK_EINTW(pins, reg, id, offs, fltcon_offs) \ + { \ + .type = &gs101_bank_type_alive, \ + .pctl_offset = reg, \ + .nr_pins = pins, \ + .eint_type = EINT_TYPE_WKUP, \ + .eint_offset = offs, \ + .fltcon_type = FLT_SELECTABLE, \ + .fltcon_offset = fltcon_offs, \ + .name = id \ + } + /** * struct exynos_weint_data: irq specific data for all the wakeup interrupts * generated by the external wakeup interrupt controller. diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.c b/drivers/pinctrl/samsung/pinctrl-samsung.c index 50c360b4753a..982a5702714c 100644 --- a/drivers/pinctrl/samsung/pinctrl-samsung.c +++ b/drivers/pinctrl/samsung/pinctrl-samsung.c @@ -1323,6 +1323,8 @@ static const struct of_device_id samsung_pinctrl_dt_match[] = { .data = &exynosautov9_of_data }, { .compatible = "tesla,fsd-pinctrl", .data = &fsd_of_data }, + { .compatible = "google,gs101-pinctrl", + .data = &gs101_of_data }, #endif #ifdef CONFIG_PINCTRL_S3C64XX { .compatible = "samsung,s3c64xx-pinctrl", diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h b/drivers/pinctrl/samsung/pinctrl-samsung.h index 5fab3885a7d7..f6856290608c 100644 --- a/drivers/pinctrl/samsung/pinctrl-samsung.h +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h @@ -373,6 +373,7 @@ extern const struct samsung_pinctrl_of_match_data exynos7885_of_data; extern const struct samsung_pinctrl_of_match_data exynos850_of_data; extern const struct samsung_pinctrl_of_match_data exynosautov9_of_data; extern const struct samsung_pinctrl_of_match_data fsd_of_data; +extern const struct samsung_pinctrl_of_match_data gs101_of_data; extern const struct samsung_pinctrl_of_match_data s3c64xx_of_data; extern const struct samsung_pinctrl_of_match_data s3c2412_of_data; extern const struct samsung_pinctrl_of_match_data s3c2416_of_data;
Add support for the pin-controller found on the gs101 SoC used in Pixel 6 phones. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> --- .../pinctrl/samsung/pinctrl-exynos-arm64.c | 159 ++++++++++++++++++ drivers/pinctrl/samsung/pinctrl-exynos.c | 2 + drivers/pinctrl/samsung/pinctrl-exynos.h | 34 ++++ drivers/pinctrl/samsung/pinctrl-samsung.c | 2 + drivers/pinctrl/samsung/pinctrl-samsung.h | 1 + 5 files changed, 198 insertions(+)