| Message ID | 20240122090228.28363-1-kimseer.paller@analog.com (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
| Series | [v7,1/2] dt-bindings: iio: frequency: add admfm2000 | expand |
On Mon, Jan 22, 2024 at 05:02:27PM +0800, Kim Seer Paller wrote: > Dual microwave down converter module with input RF and LO frequency > ranges from 0.5 to 32 GHz and an output IF frequency range from 0.1 to > 8 GHz. It consists of a LNA, mixer, IF filter, DSA, and IF amplifier > for each down conversion path. > > Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com> > --- > V6 -> V7: Changed RF path mode property to boolean. In the process, the description went from attempting to explain what the property did to the perfunctory "enable mixer mode". Can you please add an adequate description of the property that covers what happens when the property is omitted and what "mixer mode" actually does? > V5 -> V6: Moved array of switch and attenuation GPIOs to the channel node. > Changed pin coords with friendly names. Removed Reviewed-by tag. > V4 -> V5: Added Reviewed-by tag. > V3 -> V4: Updated the description of the properties with multiple entries and > defined the order. > V2 -> V3: Adjusted indentation to resolve wrong indentation warning. > Changed node name to converter. Updated the descriptions to clarify > the properties. > V1 -> V2: Removed '|' after description. Specified the pins connected to > the GPIOs. Added additionalProperties: false. Changed node name to gpio. > Aligned < syntax with the previous syntax in the examples. > > .../bindings/iio/frequency/adi,admfm2000.yaml | 124 ++++++++++++++++++ > MAINTAINERS | 7 + > 2 files changed, 131 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml > > diff --git a/Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml b/Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml > new file mode 100644 > index 000000000000..9e716f59d678 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml > @@ -0,0 +1,124 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +# Copyright 2024 Analog Devices Inc. > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/frequency/adi,admfm2000.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: ADMFM2000 Dual Microwave Down Converter > + > +maintainers: > + - Kim Seer Paller <kimseer.paller@analog.com> > + > +description: > + Dual microwave down converter module with input RF and LO frequency ranges > + from 0.5 to 32 GHz and an output IF frequency range from 0.1 to 8 GHz. > + It consists of a LNA, mixer, IF filter, DSA, and IF amplifier for each down > + conversion path. > + > +properties: > + compatible: > + enum: > + - adi,admfm2000 > + > + '#address-cells': > + const: 1 > + > + '#size-cells': > + const: 0 > + > +patternProperties: > + "^channel@[0-1]$": > + type: object > + description: Represents a channel of the device. > + > + additionalProperties: false > + > + properties: > + reg: > + description: > + The channel number. > + minimum: 0 > + maximum: 1 > + > + adi,mixer-mode: > + description: > + Enable mixer mode. > + type: boolean > + > + switch-gpios: > + description: | > + GPIOs to select the RF path for the channel. > + SW-CH1 CTRL-A CTRL-B > + SW-CH2 CTRL-A CTRL-B CH1 Status CH2 Status > + 1 0 Direct IF mode Mixer mode > + 0 1 Mixer mode Direct IF mode I cannot make sense of this table you have here, the double header row you have going on is hard to follow. There's also no mention here of what happens when both GPIOs are 0 or both GPIO are 1. Are these configurations permitted? Thanks, Conor > + items: > + - description: SW-CH-CTRL-A GPIO > + - description: SW-CH-CTRL-B GPIO > + > + attenuation-gpios: > + description: | > + Choice of attenuation: > + DSA-V4 DSA-V3 DSA-V2 DSA-V1 DSA-V0 > + 1 1 1 1 1 0 dB > + 1 1 1 1 0 -1 dB > + 1 1 1 0 1 -2 dB > + 1 1 0 1 1 -4 dB > + 1 0 1 1 1 -8 dB > + 0 1 1 1 1 -16 dB > + 0 0 0 0 0 -31 dB > + > + items: > + - description: DSA-V0 GPIO > + - description: DSA-V1 GPIO > + - description: DSA-V2 GPIO > + - description: DSA-V3 GPIO > + - description: DSA-V4 GPIO > + > + required: > + - reg > + - switch-gpios > + - attenuation-gpios > + > +required: > + - compatible > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + converter { > + compatible = "adi,admfm2000"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + channel@0 { > + reg = <0>; > + switch-gpios = <&gpio 1 GPIO_ACTIVE_LOW>, > + <&gpio 2 GPIO_ACTIVE_HIGH>; > + > + attenuation-gpios = <&gpio 17 GPIO_ACTIVE_LOW>, > + <&gpio 22 GPIO_ACTIVE_LOW>, > + <&gpio 23 GPIO_ACTIVE_LOW>, > + <&gpio 24 GPIO_ACTIVE_LOW>, > + <&gpio 25 GPIO_ACTIVE_LOW>; > + }; > + > + channel@1 { > + reg = <1>; > + adi,mixer-mode; > + switch-gpios = <&gpio 3 GPIO_ACTIVE_LOW>, > + <&gpio 4 GPIO_ACTIVE_HIGH>; > + > + attenuation-gpios = <&gpio 0 GPIO_ACTIVE_LOW>, > + <&gpio 5 GPIO_ACTIVE_LOW>, > + <&gpio 6 GPIO_ACTIVE_LOW>, > + <&gpio 16 GPIO_ACTIVE_LOW>, > + <&gpio 26 GPIO_ACTIVE_LOW>; > + }; > + }; > +... > diff --git a/MAINTAINERS b/MAINTAINERS > index 8d1052fa6a69..1f7cd2e848de 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -1267,6 +1267,13 @@ W: https://ez.analog.com/linux-software-drivers > F: Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml > F: drivers/hwmon/adm1177.c > > +ANALOG DEVICES INC ADMFM2000 DRIVER > +M: Kim Seer Paller <kimseer.paller@analog.com> > +L: linux-iio@vger.kernel.org > +S: Supported > +W: https://ez.analog.com/linux-software-drivers > +F: Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml > + > ANALOG DEVICES INC ADMV1013 DRIVER > M: Antoniu Miclaus <antoniu.miclaus@analog.com> > L: linux-iio@vger.kernel.org > > base-commit: 32f764943a21c1af01016bbcd43605220c076262 > -- > 2.34.1 >
> > + adi,mixer-mode: > > + description: > > + Enable mixer mode. > > + type: boolean > > + > > + switch-gpios: > > + description: | > > + GPIOs to select the RF path for the channel. > > + SW-CH1 CTRL-A CTRL-B > > + SW-CH2 CTRL-A CTRL-B CH1 Status CH2 Status > > + 1 0 Direct IF mode Mixer mode > > + 0 1 Mixer mode Direct IF mode > > I cannot make sense of this table you have here, the double header row you > have going on is hard to follow. There's also no mention here of what happens > when both GPIOs are 0 or both GPIO are 1. Are these configurations permitted? I also feel that it's quite hard to understand without the gridlines. In the preliminary datasheet, it's a switch control table, and I'm trying to replicate the way it is presented. On the table, each channel has control pins (CTRL-A and CTRL-B). For a mixer mode configuration on channel 1, CTRL-A GPIO should be 0, and CTRL-B GPIO should be 1. It's not permitted when both GPIOs are 0 or both GPIOs are 1. The state for the GPIO should strictly follow the truth table. I'm considering making it much easier to understand by creating two separate tables for each channel, just like the example below. Or is it preferred if it could be discussed in a sort of paragraph form? SW-CH1 CTRL-A CTRL-B CH1 Status CH2 Status 1 0 Direct IF mode Mixer SW-CH2 CTRL-A CTRL-B CH1 Status CH2 Status 0 1 Direct IF mode Mixer Best regards, Kim
On Mon, Jan 22, 2024 at 11:06:08AM +0000, Paller, Kim Seer wrote: > > > + adi,mixer-mode: > > > + description: > > > + Enable mixer mode. > > > + type: boolean > > > + > > > + switch-gpios: > > > + description: | > > > + GPIOs to select the RF path for the channel. > > > + SW-CH1 CTRL-A CTRL-B > > > + SW-CH2 CTRL-A CTRL-B CH1 Status CH2 Status > > > + 1 0 Direct IF mode Mixer mode > > > + 0 1 Mixer mode Direct IF mode > > > > I cannot make sense of this table you have here, the double header row you > > have going on is hard to follow. There's also no mention here of what happens > > when both GPIOs are 0 or both GPIO are 1. Are these configurations permitted? > > I also feel that it's quite hard to understand without the gridlines. In the preliminary > datasheet, it's a switch control table, and I'm trying to replicate the way it is presented. > > On the table, each channel has control pins (CTRL-A and CTRL-B). For a mixer mode > configuration on channel 1, CTRL-A GPIO should be 0, and CTRL-B GPIO should be 1. > It's not permitted when both GPIOs are 0 or both GPIOs are 1. The state for the GPIO > should strictly follow the truth table. > > I'm considering making it much easier to understand by creating two separate tables for > each channel, just like the example below. Or is it preferred if it could be discussed in > a sort of paragraph form? > > SW-CH1 CTRL-A CTRL-B CH1 Status CH2 Status > 1 0 Direct IF mode Mixer > > SW-CH2 CTRL-A CTRL-B CH1 Status CH2 Status > 0 1 Direct IF mode Mixer I think it would be sufficient to cut down the original table to something like: CTRL-A CTRL-B CH1 Status CH2 Status 1 0 Direct IF mode Mixer mode 0 1 Mixer mode Direct IF mode And state that the configurations where A == B are not permitted.
diff --git a/Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml b/Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml new file mode 100644 index 000000000000..9e716f59d678 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml @@ -0,0 +1,124 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright 2024 Analog Devices Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/frequency/adi,admfm2000.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ADMFM2000 Dual Microwave Down Converter + +maintainers: + - Kim Seer Paller <kimseer.paller@analog.com> + +description: + Dual microwave down converter module with input RF and LO frequency ranges + from 0.5 to 32 GHz and an output IF frequency range from 0.1 to 8 GHz. + It consists of a LNA, mixer, IF filter, DSA, and IF amplifier for each down + conversion path. + +properties: + compatible: + enum: + - adi,admfm2000 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + "^channel@[0-1]$": + type: object + description: Represents a channel of the device. + + additionalProperties: false + + properties: + reg: + description: + The channel number. + minimum: 0 + maximum: 1 + + adi,mixer-mode: + description: + Enable mixer mode. + type: boolean + + switch-gpios: + description: | + GPIOs to select the RF path for the channel. + SW-CH1 CTRL-A CTRL-B + SW-CH2 CTRL-A CTRL-B CH1 Status CH2 Status + 1 0 Direct IF mode Mixer mode + 0 1 Mixer mode Direct IF mode + + items: + - description: SW-CH-CTRL-A GPIO + - description: SW-CH-CTRL-B GPIO + + attenuation-gpios: + description: | + Choice of attenuation: + DSA-V4 DSA-V3 DSA-V2 DSA-V1 DSA-V0 + 1 1 1 1 1 0 dB + 1 1 1 1 0 -1 dB + 1 1 1 0 1 -2 dB + 1 1 0 1 1 -4 dB + 1 0 1 1 1 -8 dB + 0 1 1 1 1 -16 dB + 0 0 0 0 0 -31 dB + + items: + - description: DSA-V0 GPIO + - description: DSA-V1 GPIO + - description: DSA-V2 GPIO + - description: DSA-V3 GPIO + - description: DSA-V4 GPIO + + required: + - reg + - switch-gpios + - attenuation-gpios + +required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + converter { + compatible = "adi,admfm2000"; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0>; + switch-gpios = <&gpio 1 GPIO_ACTIVE_LOW>, + <&gpio 2 GPIO_ACTIVE_HIGH>; + + attenuation-gpios = <&gpio 17 GPIO_ACTIVE_LOW>, + <&gpio 22 GPIO_ACTIVE_LOW>, + <&gpio 23 GPIO_ACTIVE_LOW>, + <&gpio 24 GPIO_ACTIVE_LOW>, + <&gpio 25 GPIO_ACTIVE_LOW>; + }; + + channel@1 { + reg = <1>; + adi,mixer-mode; + switch-gpios = <&gpio 3 GPIO_ACTIVE_LOW>, + <&gpio 4 GPIO_ACTIVE_HIGH>; + + attenuation-gpios = <&gpio 0 GPIO_ACTIVE_LOW>, + <&gpio 5 GPIO_ACTIVE_LOW>, + <&gpio 6 GPIO_ACTIVE_LOW>, + <&gpio 16 GPIO_ACTIVE_LOW>, + <&gpio 26 GPIO_ACTIVE_LOW>; + }; + }; +... diff --git a/MAINTAINERS b/MAINTAINERS index 8d1052fa6a69..1f7cd2e848de 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1267,6 +1267,13 @@ W: https://ez.analog.com/linux-software-drivers F: Documentation/devicetree/bindings/hwmon/adi,adm1177.yaml F: drivers/hwmon/adm1177.c +ANALOG DEVICES INC ADMFM2000 DRIVER +M: Kim Seer Paller <kimseer.paller@analog.com> +L: linux-iio@vger.kernel.org +S: Supported +W: https://ez.analog.com/linux-software-drivers +F: Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml + ANALOG DEVICES INC ADMV1013 DRIVER M: Antoniu Miclaus <antoniu.miclaus@analog.com> L: linux-iio@vger.kernel.org
Dual microwave down converter module with input RF and LO frequency ranges from 0.5 to 32 GHz and an output IF frequency range from 0.1 to 8 GHz. It consists of a LNA, mixer, IF filter, DSA, and IF amplifier for each down conversion path. Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com> --- V6 -> V7: Changed RF path mode property to boolean. V5 -> V6: Moved array of switch and attenuation GPIOs to the channel node. Changed pin coords with friendly names. Removed Reviewed-by tag. V4 -> V5: Added Reviewed-by tag. V3 -> V4: Updated the description of the properties with multiple entries and defined the order. V2 -> V3: Adjusted indentation to resolve wrong indentation warning. Changed node name to converter. Updated the descriptions to clarify the properties. V1 -> V2: Removed '|' after description. Specified the pins connected to the GPIOs. Added additionalProperties: false. Changed node name to gpio. Aligned < syntax with the previous syntax in the examples. .../bindings/iio/frequency/adi,admfm2000.yaml | 124 ++++++++++++++++++ MAINTAINERS | 7 + 2 files changed, 131 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/frequency/adi,admfm2000.yaml base-commit: 32f764943a21c1af01016bbcd43605220c076262