diff mbox series

[v2,3/9] arm64: dts: ti: k3-am68-sk-base-board: Enable camera peripherals

Message ID 20240208084254.295289-4-vaishnav.a@ti.com (mailing list archive)
State New, archived
Headers show
Series Add CSI2RX capture support on TI J7 platforms | expand

Commit Message

Vaishnav Achath Feb. 8, 2024, 8:42 a.m. UTC 
CSI cameras are controlled using I2C. On AM68 Starter Kit, this is routed
to I2C-1, so enable the instance and the TCA9543 I2C switch on the bus.

AM68 SK schematics: https://www.ti.com/lit/zip/sprr463

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
---

V1->V2: Update commit message with schematics.

 .../boot/dts/ti/k3-am68-sk-base-board.dts     | 50 +++++++++++++++++++
 1 file changed, 50 insertions(+)

Comments

Jai Luthra Feb. 8, 2024, 10:24 a.m. UTC | #1 
On Feb 08, 2024 at 14:12:48 +0530, Vaishnav Achath wrote:
> CSI cameras are controlled using I2C. On AM68 Starter Kit, this is routed
> to I2C-1, so enable the instance and the TCA9543 I2C switch on the bus.
> 
> AM68 SK schematics: https://www.ti.com/lit/zip/sprr463
> 
> Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>

Reviewed-by: Jai Luthra <j-luthra@ti.com>

> ---
> 
> V1->V2: Update commit message with schematics.
> 
>  .../boot/dts/ti/k3-am68-sk-base-board.dts     | 50 +++++++++++++++++++
>  1 file changed, 50 insertions(+)
> 
> [...]
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
index f48155dd16a3..d743f023cdd9 100644
--- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
@@ -169,6 +169,13 @@  tfp410_out: endpoint {
 			};
 		};
 	};
+
+	csi_mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-state-cells = <1>;
+		mux-gpios = <&exp3 1 GPIO_ACTIVE_HIGH>;
+		idle-state = <0>;
+	};
 };
 
 &main_pmx0 {
@@ -186,6 +193,13 @@  J721S2_IOPAD(0x0e4, PIN_INPUT, 0) /* (AE24) I2C0_SDA */
 		>;
 	};
 
+	main_i2c1_pins_default: main-i2c1-default-pins {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0ac, PIN_INPUT, 13) /* (AC25) MCASP0_AXR15.I2C1_SCL */
+			J721S2_IOPAD(0x0b0, PIN_INPUT, 13) /* (AD26) MCASP1_AXR3.I2C1_SDA */
+		>;
+	};
+
 	main_mmc1_pins_default: main-mmc1-default-pins {
 		pinctrl-single,pins = <
 			J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */
@@ -431,6 +445,42 @@  exp1: gpio@21 {
 	};
 };
 
+&main_i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	status = "okay";
+
+	exp3: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "CSI_VIO_SEL", "CSI_SEL_FPC_EXPn",
+				  "IO_EXP_CSI2_EXP_RSTz","CSI0_B_GPIO1",
+				  "CSI1_B_GPIO1";
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9543";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		cam0_i2c: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		cam1_i2c: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+	};
+};
+
 &main_i2c4 {
 	status = "okay";
 	pinctrl-names = "default";