@@ -62,6 +62,9 @@ dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-ulcb.dtb
dtb-$(CONFIG_ARCH_R8A77965) += r8a77965-ulcb-kf.dtb
dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle.dtb
+dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle-function-expansion.dtbo
+r8a77970-eagle-function-expansion-dtbs := r8a77970-eagle.dtb r8a77970-eagle-function-expansion.dtbo
+dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-eagle-function-expansion.dtb
dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-v3msk.dtb
dtb-$(CONFIG_ARCH_R8A77980) += r8a77980-condor.dtb
new file mode 100644
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Eagle V3M Function expansion board.
+ *
+ * Copyright (C) 2024 Niklas Söderlund <niklas.soderlund@ragnatech.se>
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ /* CN4 */
+ /* Eagle: SW18 set to OFF */
+ cvbs-in-cn4 {
+ compatible = "composite-video-connector";
+ label = "CVBS IN CN4";
+
+ port {
+ cvbs_con: endpoint {
+ remote-endpoint = <&adv7482_ain7>;
+ };
+ };
+ };
+
+ /* CN2 */
+ /* Eagle: SW35 set 5, 6 and 8 to OFF */
+ hdmi-in-cn2 {
+ compatible = "hdmi-connector";
+ label = "HDMI IN CN2";
+ type = "a";
+
+ port {
+ hdmi_in_con2: endpoint {
+ remote-endpoint = <&adv7612_in>;
+ };
+ };
+ };
+
+ /* CN3 */
+ /* Eagle: SW18 set to OFF */
+ hdmi-in-cn3 {
+ compatible = "hdmi-connector";
+ label = "HDMI IN CN3";
+ type = "a";
+
+ port {
+ hdmi_in_con: endpoint {
+ remote-endpoint = <&adv7482_hdmi>;
+ };
+ };
+ };
+};
+
+/* Disconnect MAX9286 GMSL I2C. */
+&i2c3 {
+ status = "disabled";
+};
+
+/* Connect expansion board I2C. */
+&i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio@27 {
+ compatible = "onnn,pca9654";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ vin0_adv7612_en {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "VIN0_ADV7612_ENn";
+ };
+ };
+
+ hdmi-decoder@4c {
+ compatible = "adi,adv7612";
+ reg = <0x4c>, <0x50>, <0x52>, <0x54>, <0x56>, <0x58>;
+ reg-names = "main", "afe", "rep", "edid", "hdmi", "cp";
+ interrupt-parent = <&gpio3>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ default-input = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ adv7612_in: endpoint {
+ remote-endpoint = <&hdmi_in_con2>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ adv7612_out: endpoint {
+ remote-endpoint = <&vin0_in>;
+ };
+ };
+ };
+ };
+
+ video-receiver@70 {
+ compatible = "adi,adv7482";
+ reg = <0x70 0x71 0x72 0x73 0x74 0x75
+ 0x60 0x61 0x62 0x63 0x64 0x65>;
+ reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
+ "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
+ interrupt-parent = <&gpio3>;
+ interrupts = <03 IRQ_TYPE_LEVEL_LOW>, <04 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "intrq1", "intrq2";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@7 {
+ reg = <7>;
+
+ adv7482_ain7: endpoint {
+ remote-endpoint = <&cvbs_con>;
+ };
+ };
+
+ port@8 {
+ reg = <8>;
+
+ adv7482_hdmi: endpoint {
+ remote-endpoint = <&hdmi_in_con>;
+ };
+ };
+
+ port@a {
+ reg = <10>;
+
+ adv7482_txa: endpoint {
+ clock-lanes = <0>;
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&csi40_in>;
+ };
+ };
+ };
+ };
+
+};
+
+&csi40 {
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ csi40_in: endpoint {
+ clock-lanes = <0>;
+ data-lanes = <1 2 3 4>;
+ remote-endpoint = <&adv7482_txa>;
+ };
+ };
+ };
+};
+
+&pfc {
+ vin0_pins_parallel: vin0 {
+ groups = "vin0_data12", "vin0_sync", "vin0_clk", "vin0_clkenb";
+ function = "vin0";
+ };
+};
+
+&vin0 {
+ status = "okay";
+
+ pinctrl-0 = <&vin0_pins_parallel>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ vin0_in: endpoint {
+ pclk-sample = <0>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ remote-endpoint = <&adv7612_out>;
+ };
+ };
+ };
+};
+
+&vin1 {
+ status = "okay";
+};
+
+&vin2 {
+ status = "okay";
+};
+
+&vin3 {
+ status = "okay";
+};
The Eagle board supports an optional "Function expansion board". The expansion board adds support for HDMI OUT, HDMI capture from two different sources and eMMC. This change only adds support for the two HDMI capture sources. Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> --- * Changes since v1 - The board is named "Function expansion board", update all references. - Rename the over lay to r8a77970-eagle-function-expansion.dtso. - Add r8a77970-eagle-expansion.dtbo to dtb-$(CONFIG_ARCH_R8A77970) so it's considered for installation. - Move #include statements below /.../; markers. - Sort nodes without addresses in alphabetical order. - Capitalize i2c -> I2C in comments. - Use symbolic values for GPIO flags. - Adjust gpios and output-{low,high} to match that the signal is active-low. - Correct misspelled label and removed unneeded ones. --- arch/arm64/boot/dts/renesas/Makefile | 3 + .../r8a77970-eagle-function-expansion.dtso | 214 ++++++++++++++++++ 2 files changed, 217 insertions(+) create mode 100644 arch/arm64/boot/dts/renesas/r8a77970-eagle-function-expansion.dtso