@@ -20375,6 +20375,7 @@ L: linux-media@vger.kernel.org
S: Maintained
T: git git://linuxtv.org/media_tree.git
F: Documentation/devicetree/bindings/media/i2c/sony,imx283.yaml
+F: drivers/media/i2c/imx283.c
SONY IMX290 SENSOR DRIVER
M: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
@@ -153,6 +153,16 @@ config VIDEO_IMX274
This is a V4L2 sensor driver for the Sony IMX274
CMOS image sensor.
+config VIDEO_IMX283
+ tristate "Sony IMX283 sensor support"
+ select V4L2_CCI_I2C
+ help
+ This is a V4L2 sensor driver for the Sony IMX283
+ CMOS image sensor.
+
+ To compile this driver as a module, choose M here: the
+ module will be called imx283.
+
config VIDEO_IMX290
tristate "Sony IMX290 sensor support"
select REGMAP_I2C
@@ -48,6 +48,7 @@ obj-$(CONFIG_VIDEO_IMX214) += imx214.o
obj-$(CONFIG_VIDEO_IMX219) += imx219.o
obj-$(CONFIG_VIDEO_IMX258) += imx258.o
obj-$(CONFIG_VIDEO_IMX274) += imx274.o
+obj-$(CONFIG_VIDEO_IMX283) += imx283.o
obj-$(CONFIG_VIDEO_IMX290) += imx290.o
obj-$(CONFIG_VIDEO_IMX296) += imx296.o
obj-$(CONFIG_VIDEO_IMX319) += imx319.o
new file mode 100644
@@ -0,0 +1,1596 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * V4L2 Support for the IMX283
+ *
+ * Diagonal 15.86 mm (Type 1) CMOS Image Sensor with Square Pixel for Color
+ * Cameras.
+ *
+ * Copyright (C) 2024 Ideas on Board Oy.
+ *
+ * Based on Sony IMX283 driver prepared by Will Whang
+ *
+ * Based on Sony imx477 camera driver
+ * Copyright (C) 2019-2020 Raspberry Pi (Trading) Ltd
+ */
+
+#include <linux/array_size.h>
+#include <linux/bitops.h>
+#include <linux/container_of.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <linux/regulator/consumer.h>
+#include <linux/types.h>
+#include <linux/units.h>
+#include <media/v4l2-cci.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mediabus.h>
+
+/* Chip ID */
+#define IMX283_REG_CHIP_ID CCI_REG8(0x3000)
+#define IMX283_CHIP_ID 0x0b // Default power on state
+
+#define IMX283_REG_STANDBY CCI_REG8(0x3000)
+#define IMX283_ACTIVE 0
+#define IMX283_STANDBY BIT(0)
+#define IMX283_STBLOGIC BIT(1)
+#define IMX283_STBMIPI BIT(2)
+#define IMX283_STBDV BIT(3)
+#define IMX283_SLEEP BIT(4)
+
+#define IMX283_REG_CLAMP CCI_REG8(0x3001)
+#define IMX283_CLPSQRST BIT(4)
+
+#define IMX283_REG_PLSTMG08 CCI_REG8(0x3003)
+#define IMX283_PLSTMG08_VAL 0x77
+
+#define IMX283_REG_MDSEL1 CCI_REG8(0x3004)
+#define IMX283_REG_MDSEL2 CCI_REG8(0x3005)
+#define IMX283_REG_MDSEL3 CCI_REG8(0x3006)
+#define IMX283_MDSEL3_VCROP_EN BIT(5)
+#define IMX283_REG_MDSEL4 CCI_REG8(0x3007)
+#define IMX283_MDSEL4_VCROP_EN (BIT(4) | BIT(6))
+
+#define IMX283_REG_SVR CCI_REG16_LE(0x3009)
+
+#define IMX283_REG_HTRIMMING CCI_REG8(0x300b)
+#define IMX283_MDVREV BIT(0) /* VFLIP */
+#define IMX283_HTRIMMING_EN BIT(4)
+
+#define IMX283_REG_VWINPOS CCI_REG16_LE(0x300f)
+#define IMX283_REG_VWIDCUT CCI_REG16_LE(0x3011)
+
+#define IMX283_REG_MDSEL7 CCI_REG16_LE(0x3013)
+
+/* CSI Clock Configuration */
+#define IMX283_REG_TCLKPOST CCI_REG8(0x3018)
+#define IMX283_REG_THSPREPARE CCI_REG8(0x301a)
+#define IMX283_REG_THSZERO CCI_REG8(0x301c)
+#define IMX283_REG_THSTRAIL CCI_REG8(0x301e)
+#define IMX283_REG_TCLKTRAIL CCI_REG8(0x3020)
+#define IMX283_REG_TCLKPREPARE CCI_REG8(0x3022)
+#define IMX283_REG_TCLKZERO CCI_REG16_LE(0x3024)
+#define IMX283_REG_TLPX CCI_REG8(0x3026)
+#define IMX283_REG_THSEXIT CCI_REG8(0x3028)
+#define IMX283_REG_TCLKPRE CCI_REG8(0x302a)
+#define IMX283_REG_SYSMODE CCI_REG8(0x3104)
+
+#define IMX283_REG_Y_OUT_SIZE CCI_REG16_LE(0x302f)
+#define IMX283_REG_WRITE_VSIZE CCI_REG16_LE(0x3031)
+#define IMX283_REG_OB_SIZE_V CCI_REG8(0x3033)
+
+/* HMAX internal HBLANK */
+#define IMX283_REG_HMAX CCI_REG16_LE(0x3036)
+#define IMX283_HMAX_MAX (BIT(16) - 1)
+
+/* VMAX internal VBLANK */
+#define IMX283_REG_VMAX CCI_REG24_LE(0x3038)
+#define IMX283_VMAX_MAX (BIT(16) - 1)
+
+/* SHR internal */
+#define IMX283_REG_SHR CCI_REG16_LE(0x303b)
+#define IMX283_SHR_MIN 11
+
+/*
+ * Analog gain control
+ * Gain [dB] = -20log{(2048 - value [10:0]) /2048}
+ * Range: 0dB to approximately +27dB
+ */
+#define IMX283_REG_ANALOG_GAIN CCI_REG16_LE(0x3042)
+#define IMX283_ANA_GAIN_MIN 0
+#define IMX283_ANA_GAIN_MAX 1957
+#define IMX283_ANA_GAIN_STEP 1
+#define IMX283_ANA_GAIN_DEFAULT 0x0
+
+/*
+ * Digital gain control
+ * Gain [dB] = value * 6
+ * Range: 0dB to +18db
+ */
+#define IMX283_REG_DIGITAL_GAIN CCI_REG8(0x3044)
+#define IMX283_DGTL_GAIN_MIN 0
+#define IMX283_DGTL_GAIN_MAX 3
+#define IMX283_DGTL_GAIN_DEFAULT 0
+#define IMX283_DGTL_GAIN_STEP 1
+
+#define IMX283_REG_HTRIMMING_START CCI_REG16_LE(0x3058)
+#define IMX283_REG_HTRIMMING_END CCI_REG16_LE(0x305a)
+
+#define IMX283_REG_MDSEL18 CCI_REG16_LE(0x30f6)
+
+/* Master Mode Operation Control */
+#define IMX283_REG_XMSTA CCI_REG8(0x3105)
+#define IMX283_XMSTA BIT(0)
+
+#define IMX283_REG_SYNCDRV CCI_REG8(0x3107)
+#define IMX283_SYNCDRV_XHS_XVS (0xa0 | 0x02)
+#define IMX283_SYNCDRV_HIZ (0xa0 | 0x03)
+
+/* PLL Standby */
+#define IMX283_REG_STBPL CCI_REG8(0x320b)
+#define IMX283_STBPL_NORMAL 0x00
+#define IMX283_STBPL_STANDBY 0x03
+
+/* Input Frequency Setting */
+#define IMX283_REG_PLRD1 CCI_REG8(0x36c1)
+#define IMX283_REG_PLRD2 CCI_REG16_LE(0x36c2)
+#define IMX283_REG_PLRD3 CCI_REG8(0x36f7)
+#define IMX283_REG_PLRD4 CCI_REG8(0x36f8)
+
+#define IMX283_REG_PLSTMG02 CCI_REG8(0x36aa)
+#define IMX283_PLSTMG02_VAL 0x00
+
+#define IMX283_REG_EBD_X_OUT_SIZE CCI_REG16_LE(0x3a54)
+
+/* Test pattern generator */
+#define IMX283_REG_TPG_CTRL CCI_REG8(0x3156)
+#define IMX283_TPG_CTRL_CLKEN BIT(0)
+#define IMX283_TPG_CTRL_PATEN BIT(4)
+
+#define IMX283_REG_TPG_PAT CCI_REG8(0x3157)
+#define IMX283_TPG_PAT_ALL_000 0x00
+#define IMX283_TPG_PAT_ALL_FFF 0x01
+#define IMX283_TPG_PAT_ALL_555 0x02
+#define IMX283_TPG_PAT_ALL_AAA 0x03
+#define IMX283_TPG_PAT_H_COLOR_BARS 0x0a
+#define IMX283_TPG_PAT_V_COLOR_BARS 0x0b
+
+/* Exposure control */
+#define IMX283_EXPOSURE_MIN 52
+#define IMX283_EXPOSURE_STEP 1
+#define IMX283_EXPOSURE_DEFAULT 1000
+#define IMX283_EXPOSURE_MAX 49865
+
+#define IMAGE_PAD 0
+
+#define IMX283_XCLR_MIN_DELAY_US (1 * USEC_PER_MSEC)
+#define IMX283_XCLR_DELAY_RANGE_US (1 * USEC_PER_MSEC)
+
+/* IMX283 native and active pixel array size. */
+static const struct v4l2_rect imx283_native_area = {
+ .top = 0,
+ .left = 0,
+ .width = 5592,
+ .height = 3710,
+};
+
+static const struct v4l2_rect imx283_active_area = {
+ .top = 40,
+ .left = 108,
+ .width = 5472,
+ .height = 3648,
+};
+
+struct imx283_reg_list {
+ unsigned int num_of_regs;
+ const struct cci_reg_sequence *regs;
+};
+
+/* Mode : resolution and related config values */
+struct imx283_mode {
+ unsigned int mode;
+
+ /* Bits per pixel */
+ unsigned int bpp;
+
+ /* Frame width */
+ unsigned int width;
+
+ /* Frame height */
+ unsigned int height;
+
+ /*
+ * Minimum horizontal timing in pixel-units
+ *
+ * Note that HMAX is written in 72MHz units, and the datasheet assumes a
+ * 720MHz link frequency. Convert datasheet values with the following:
+ *
+ * For 12 bpp modes (480Mbps) convert with:
+ * hmax = [hmax in 72MHz units] * 480 / 72
+ *
+ * For 10 bpp modes (576Mbps) convert with:
+ * hmax = [hmax in 72MHz units] * 576 / 72
+ */
+ u32 min_hmax;
+
+ /* minimum V-timing in lines */
+ u32 min_vmax;
+
+ /* default H-timing */
+ u32 default_hmax;
+
+ /* default V-timing */
+ u32 default_vmax;
+
+ /* minimum SHR */
+ u32 min_shr;
+
+ /*
+ * Per-mode vertical crop constants used to calculate values
+ * of IMX283REG_WIDCUT and IMX283_REG_VWINPOS.
+ */
+ u32 veff;
+ u32 vst;
+ u32 vct;
+
+ /* Horizontal and vertical binning ratio */
+ u8 hbin_ratio;
+ u8 vbin_ratio;
+
+ /* Optical Blanking */
+ u32 horizontal_ob;
+ u32 vertical_ob;
+
+ /* Analog crop rectangle. */
+ struct v4l2_rect crop;
+};
+
+struct imx283_input_frequency {
+ unsigned int mhz;
+ unsigned int reg_count;
+ struct cci_reg_sequence regs[4];
+};
+
+static const struct imx283_input_frequency imx283_frequencies[] = {
+ {
+ .mhz = 6 * HZ_PER_MHZ,
+ .reg_count = 4,
+ .regs = {
+ { IMX283_REG_PLRD1, 0x00 },
+ { IMX283_REG_PLRD2, 0x00f0 },
+ { IMX283_REG_PLRD3, 0x00 },
+ { IMX283_REG_PLRD4, 0xc0 },
+ },
+ },
+ {
+ .mhz = 12 * HZ_PER_MHZ,
+ .reg_count = 4,
+ .regs = {
+ { IMX283_REG_PLRD1, 0x01 },
+ { IMX283_REG_PLRD2, 0x00f0 },
+ { IMX283_REG_PLRD3, 0x01 },
+ { IMX283_REG_PLRD4, 0xc0 },
+ },
+ },
+ {
+ .mhz = 18 * HZ_PER_MHZ,
+ .reg_count = 4,
+ .regs = {
+ { IMX283_REG_PLRD1, 0x01 },
+ { IMX283_REG_PLRD2, 0x00a0 },
+ { IMX283_REG_PLRD3, 0x01 },
+ { IMX283_REG_PLRD4, 0x80 },
+ },
+ },
+ {
+ .mhz = 24 * HZ_PER_MHZ,
+ .reg_count = 4,
+ .regs = {
+ { IMX283_REG_PLRD1, 0x02 },
+ { IMX283_REG_PLRD2, 0x00f0 },
+ { IMX283_REG_PLRD3, 0x02 },
+ { IMX283_REG_PLRD4, 0xc0 },
+ },
+ },
+};
+
+enum imx283_modes {
+ IMX283_MODE_0,
+ IMX283_MODE_1,
+ IMX283_MODE_1A,
+ IMX283_MODE_1S,
+ IMX283_MODE_2,
+ IMX283_MODE_2A,
+ IMX283_MODE_3,
+ IMX283_MODE_4,
+ IMX283_MODE_5,
+ IMX283_MODE_6,
+};
+
+struct imx283_readout_mode {
+ u8 mdsel1;
+ u8 mdsel2;
+ u8 mdsel3;
+ u8 mdsel4;
+};
+
+static const struct imx283_readout_mode imx283_readout_modes[] = {
+ /* All pixel scan modes */
+ [IMX283_MODE_0] = { 0x04, 0x03, 0x10, 0x00 }, /* 12 bit */
+ [IMX283_MODE_1] = { 0x04, 0x01, 0x00, 0x00 }, /* 10 bit */
+ [IMX283_MODE_1A] = { 0x04, 0x01, 0x20, 0x50 }, /* 10 bit */
+ [IMX283_MODE_1S] = { 0x04, 0x41, 0x20, 0x50 }, /* 10 bit */
+
+ /* Horizontal / Vertical 2/2-line binning */
+ [IMX283_MODE_2] = { 0x0d, 0x11, 0x50, 0x00 }, /* 12 bit */
+ [IMX283_MODE_2A] = { 0x0d, 0x11, 0x70, 0x50 }, /* 12 bit */
+
+ /* Horizontal / Vertical 3/3-line binning */
+ [IMX283_MODE_3] = { 0x1e, 0x18, 0x10, 0x00 }, /* 12 bit */
+
+ /* Vertical 2/9 subsampling, horizontal 3 binning cropping */
+ [IMX283_MODE_4] = { 0x29, 0x18, 0x30, 0x50 }, /* 12 bit */
+
+ /* Vertical 2/19 subsampling binning, horizontal 3 binning */
+ [IMX283_MODE_5] = { 0x2d, 0x18, 0x10, 0x00 }, /* 12 bit */
+
+ /* Vertical 2 binning horizontal 2/4, subsampling 16:9 cropping */
+ [IMX283_MODE_6] = { 0x18, 0x21, 0x00, 0x09 }, /* 10 bit */
+
+ /*
+ * New modes should make sure the offset period is complied.
+ * See imx283_exposure() for reference.
+ */
+};
+
+static const struct cci_reg_sequence mipi_data_rate_1440Mbps[] = {
+ /* The default register settings provide the 1440Mbps rate */
+ { CCI_REG8(0x36c5), 0x00 }, /* Undocumented */
+ { CCI_REG8(0x3ac4), 0x00 }, /* Undocumented */
+
+ { IMX283_REG_STBPL, 0x00 },
+ { IMX283_REG_TCLKPOST, 0xa7 },
+ { IMX283_REG_THSPREPARE, 0x6f },
+ { IMX283_REG_THSZERO, 0x9f },
+ { IMX283_REG_THSTRAIL, 0x5f },
+ { IMX283_REG_TCLKTRAIL, 0x5f },
+ { IMX283_REG_TCLKPREPARE, 0x6f },
+ { IMX283_REG_TCLKZERO, 0x017f },
+ { IMX283_REG_TLPX, 0x4f },
+ { IMX283_REG_THSEXIT, 0x47 },
+ { IMX283_REG_TCLKPRE, 0x07 },
+ { IMX283_REG_SYSMODE, 0x02 },
+};
+
+static const struct cci_reg_sequence mipi_data_rate_720Mbps[] = {
+ /* Undocumented Additions "For 720MBps" Setting */
+ { CCI_REG8(0x36c5), 0x01 }, /* Undocumented */
+ { CCI_REG8(0x3ac4), 0x01 }, /* Undocumented */
+
+ { IMX283_REG_STBPL, 0x00 },
+ { IMX283_REG_TCLKPOST, 0x77 },
+ { IMX283_REG_THSPREPARE, 0x37 },
+ { IMX283_REG_THSZERO, 0x67 },
+ { IMX283_REG_THSTRAIL, 0x37 },
+ { IMX283_REG_TCLKTRAIL, 0x37 },
+ { IMX283_REG_TCLKPREPARE, 0x37 },
+ { IMX283_REG_TCLKZERO, 0xdf },
+ { IMX283_REG_TLPX, 0x2f },
+ { IMX283_REG_THSEXIT, 0x47 },
+ { IMX283_REG_TCLKPRE, 0x0f },
+ { IMX283_REG_SYSMODE, 0x02 },
+};
+
+static const s64 link_frequencies[] = {
+ 720 * HZ_PER_MHZ, /* 1440 Mbps lane data rate */
+ 360 * HZ_PER_MHZ, /* 720 Mbps data lane rate */
+};
+
+static const struct imx283_reg_list link_freq_reglist[] = {
+ { /* 720 MHz */
+ .num_of_regs = ARRAY_SIZE(mipi_data_rate_1440Mbps),
+ .regs = mipi_data_rate_1440Mbps,
+ },
+ { /* 360 MHz */
+ .num_of_regs = ARRAY_SIZE(mipi_data_rate_720Mbps),
+ .regs = mipi_data_rate_720Mbps,
+ },
+};
+
+#define CENTERED_RECTANGLE(rect, _width, _height) \
+ { \
+ .left = rect.left + ((rect.width - (_width)) / 2), \
+ .top = rect.top + ((rect.height - (_height)) / 2), \
+ .width = (_width), \
+ .height = (_height), \
+ }
+
+/* Mode configs */
+static const struct imx283_mode supported_modes_12bit[] = {
+ {
+ /* 20MPix 21.40 fps readout mode 0 */
+ .mode = IMX283_MODE_0,
+ .bpp = 12,
+ .width = 5472,
+ .height = 3648,
+ .min_hmax = 5914, /* 887 @ 480MHz/72MHz */
+ .min_vmax = 3793, /* Lines */
+
+ .veff = 3694,
+ .vst = 0,
+ .vct = 0,
+
+ .hbin_ratio = 1,
+ .vbin_ratio = 1,
+
+ /* 20.00 FPS */
+ .default_hmax = 6000, /* 900 @ 480MHz/72MHz */
+ .default_vmax = 4000,
+
+ .min_shr = 11,
+ .horizontal_ob = 96,
+ .vertical_ob = 16,
+ .crop = CENTERED_RECTANGLE(imx283_active_area, 5472, 3648),
+ },
+ {
+ /*
+ * Readout mode 2 : 2/2 binned mode (2736x1824)
+ */
+ .mode = IMX283_MODE_2,
+ .bpp = 12,
+ .width = 2736,
+ .height = 1824,
+ .min_hmax = 1870, /* Pixels (362 * 360/72 + padding) */
+ .min_vmax = 3840, /* Lines */
+
+ /* 50.00 FPS */
+ .default_hmax = 1870, /* 362 @ 360MHz/72MHz */
+ .default_vmax = 3960,
+
+ .veff = 1824,
+ .vst = 0,
+ .vct = 0,
+
+ .hbin_ratio = 2,
+ .vbin_ratio = 2,
+
+ .min_shr = 12,
+ .horizontal_ob = 48,
+ .vertical_ob = 4,
+
+ .crop = CENTERED_RECTANGLE(imx283_active_area, 5472, 3648),
+ },
+};
+
+static const struct imx283_mode supported_modes_10bit[] = {
+ {
+ /* 20MPix 25.48 fps readout mode 1 */
+ .mode = IMX283_MODE_1,
+ .bpp = 10,
+ .width = 5472,
+ .height = 3648,
+ .min_hmax = 5960, /* 745 @ 576MHz / 72MHz */
+ .min_vmax = 3793,
+
+ /* 25.00 FPS */
+ .default_hmax = 1500, /* 750 @ 576MHz / 72MHz */
+ .default_vmax = 3840,
+
+ .min_shr = 10,
+ .horizontal_ob = 96,
+ .vertical_ob = 16,
+ .crop = CENTERED_RECTANGLE(imx283_active_area, 5472, 3648),
+ },
+};
+
+static const u32 imx283_mbus_codes[] = {
+ MEDIA_BUS_FMT_SRGGB12_1X12,
+ MEDIA_BUS_FMT_SRGGB10_1X10,
+};
+
+/* regulator supplies */
+static const char *const imx283_supply_name[] = {
+ "vadd", /* Analog (2.9V) supply */
+ "vdd1", /* Supply Voltage 2 (1.8V) supply */
+ "vdd2", /* Supply Voltage 3 (1.2V) supply */
+};
+
+struct imx283 {
+ struct device *dev;
+ struct regmap *cci;
+
+ const struct imx283_input_frequency *freq;
+
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+
+ struct clk *xclk;
+
+ struct gpio_desc *reset_gpio;
+ struct regulator_bulk_data supplies[ARRAY_SIZE(imx283_supply_name)];
+
+ /* V4L2 Controls */
+ struct v4l2_ctrl_handler ctrl_handler;
+ struct v4l2_ctrl *exposure;
+ struct v4l2_ctrl *vblank;
+ struct v4l2_ctrl *hblank;
+ struct v4l2_ctrl *vflip;
+
+ unsigned long link_freq_bitmap;
+
+ u16 hmax;
+ u32 vmax;
+};
+
+static inline struct imx283 *to_imx283(struct v4l2_subdev *sd)
+{
+ return container_of_const(sd, struct imx283, sd);
+}
+
+static inline void get_mode_table(unsigned int code,
+ const struct imx283_mode **mode_list,
+ unsigned int *num_modes)
+{
+ switch (code) {
+ case MEDIA_BUS_FMT_SRGGB12_1X12:
+ case MEDIA_BUS_FMT_SGRBG12_1X12:
+ case MEDIA_BUS_FMT_SGBRG12_1X12:
+ case MEDIA_BUS_FMT_SBGGR12_1X12:
+ *mode_list = supported_modes_12bit;
+ *num_modes = ARRAY_SIZE(supported_modes_12bit);
+ break;
+
+ case MEDIA_BUS_FMT_SRGGB10_1X10:
+ case MEDIA_BUS_FMT_SGRBG10_1X10:
+ case MEDIA_BUS_FMT_SGBRG10_1X10:
+ case MEDIA_BUS_FMT_SBGGR10_1X10:
+ *mode_list = supported_modes_10bit;
+ *num_modes = ARRAY_SIZE(supported_modes_10bit);
+ break;
+ default:
+ *mode_list = NULL;
+ *num_modes = 0;
+ break;
+ }
+}
+
+/* Calculate the Pixel Rate based on the current mode */
+static u64 imx283_pixel_rate(struct imx283 *imx283,
+ const struct imx283_mode *mode)
+{
+ unsigned int bpp = mode->bpp;
+ const unsigned int ddr = 2; /* Double Data Rate */
+ const unsigned int lanes = 4; /* Only 4 lane support */
+ u64 link_frequency = link_frequencies[__ffs(imx283->link_freq_bitmap)];
+
+ return link_frequency * ddr * lanes / bpp;
+}
+
+/* Convert from a variable pixel_rate to 72 MHz clock cycles */
+static u64 imx283_internal_clock(unsigned int pixel_rate, unsigned int pixels)
+{
+ /*
+ * Determine the following operation without overflow:
+ * pixels = 72 Mhz / pixel_rate
+ *
+ * The internal clock at 72MHz and Pixel Rate (between 240 and 576MHz)
+ * can easily overflow this calculation, so pre-divide to simplify.
+ */
+ const u32 iclk_pre = 72;
+ const u32 pclk_pre = pixel_rate / HZ_PER_MHZ;
+
+ return pixels * iclk_pre / pclk_pre;
+}
+
+/* Internal clock (72MHz) to Pixel Rate clock (Variable) */
+static u64 imx283_iclk_to_pix(unsigned int pixel_rate, unsigned int cycles)
+{
+ /*
+ * Determine the following operation without overflow:
+ * cycles * pixel_rate / 72 MHz
+ *
+ * The internal clock at 72MHz and Pixel Rate (between 240 and 576MHz)
+ * can easily overflow this calculation, so pre-divide to simplify.
+ */
+ const u32 iclk_pre = 72;
+ const u32 pclk_pre = pixel_rate / HZ_PER_MHZ;
+
+ return cycles * pclk_pre / iclk_pre;
+}
+
+/* Determine the exposure based on current hmax, vmax and a given SHR */
+static u32 imx283_exposure(struct imx283 *imx283,
+ const struct imx283_mode *mode, u64 shr)
+{
+ u32 svr = 0; /* SVR feature is not currently supported */
+ u32 offset;
+ u64 numerator;
+
+ /* Number of clocks per internal offset period */
+ offset = mode->mode == IMX283_MODE_0 ? 209 : 157;
+ numerator = (imx283->vmax * (svr + 1) - shr) * imx283->hmax + offset;
+
+ do_div(numerator, imx283->hmax);
+
+ return clamp(numerator, 0, U32_MAX);
+}
+
+static void imx283_exposure_limits(struct imx283 *imx283,
+ const struct imx283_mode *mode,
+ s64 *min_exposure, s64 *max_exposure)
+{
+ u32 svr = 0; /* SVR feature is not currently supported */
+ u64 min_shr = mode->min_shr;
+ /* Global Shutter is not supported */
+ u64 max_shr = (svr + 1) * imx283->vmax - 4;
+
+ max_shr = min(max_shr, BIT(16) - 1);
+
+ *min_exposure = imx283_exposure(imx283, mode, max_shr);
+ *max_exposure = imx283_exposure(imx283, mode, min_shr);
+}
+
+/*
+ * Integration Time [s] = [ {VMAX x (SVR + 1) – (SHR)} x HMAX + offset ]
+ * / [ 72 x 10^6 ]
+ */
+static u32 imx283_shr(struct imx283 *imx283, const struct imx283_mode *mode,
+ u32 exposure)
+{
+ u32 svr = 0; /* SVR feature is not currently supported */
+ u32 offset;
+ u64 temp;
+
+ /* Number of clocks per internal offset period */
+ offset = mode->mode == IMX283_MODE_0 ? 209 : 157;
+ temp = ((u64)exposure * imx283->hmax - offset);
+ do_div(temp, imx283->hmax);
+
+ return (imx283->vmax * (svr + 1) - temp);
+}
+
+static const char * const imx283_tpg_menu[] = {
+ "Disabled",
+ "All 000h",
+ "All FFFh",
+ "All 555h",
+ "All AAAh",
+ "Horizontal color bars",
+ "Vertical color bars",
+};
+
+static const int imx283_tpg_val[] = {
+ IMX283_TPG_PAT_ALL_000,
+ IMX283_TPG_PAT_ALL_000,
+ IMX283_TPG_PAT_ALL_FFF,
+ IMX283_TPG_PAT_ALL_555,
+ IMX283_TPG_PAT_ALL_AAA,
+ IMX283_TPG_PAT_H_COLOR_BARS,
+ IMX283_TPG_PAT_V_COLOR_BARS,
+};
+
+static int imx283_update_test_pattern(struct imx283 *imx283, u32 pattern_index)
+{
+ int ret;
+
+ if (pattern_index >= ARRAY_SIZE(imx283_tpg_val))
+ return -EINVAL;
+
+ if (!pattern_index)
+ return cci_write(imx283->cci, IMX283_REG_TPG_CTRL, 0x00, NULL);
+
+ ret = cci_write(imx283->cci, IMX283_REG_TPG_PAT,
+ imx283_tpg_val[pattern_index], NULL);
+ if (ret)
+ return ret;
+
+ return cci_write(imx283->cci, IMX283_REG_TPG_CTRL,
+ IMX283_TPG_CTRL_CLKEN | IMX283_TPG_CTRL_PATEN, NULL);
+}
+
+static int imx283_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct imx283 *imx283 = container_of(ctrl->handler, struct imx283,
+ ctrl_handler);
+ const struct imx283_mode *mode;
+ struct v4l2_mbus_framefmt *fmt;
+ const struct imx283_mode *mode_list;
+ struct v4l2_subdev_state *state;
+ unsigned int num_modes;
+ u64 shr, pixel_rate;
+ int ret = 0;
+
+ state = v4l2_subdev_get_locked_active_state(&imx283->sd);
+ fmt = v4l2_subdev_state_get_format(state, 0);
+
+ get_mode_table(fmt->code, &mode_list, &num_modes);
+ mode = v4l2_find_nearest_size(mode_list, num_modes, width, height,
+ fmt->width, fmt->height);
+
+ /*
+ * The VBLANK control may change the limits of usable exposure, so check
+ * and adjust if necessary.
+ */
+ if (ctrl->id == V4L2_CID_VBLANK) {
+ /* Honour the VBLANK limits when setting exposure. */
+ s64 current_exposure, max_exposure, min_exposure;
+
+ imx283->vmax = mode->height + ctrl->val;
+
+ imx283_exposure_limits(imx283, mode,
+ &min_exposure, &max_exposure);
+
+ current_exposure = imx283->exposure->val;
+ current_exposure = clamp(current_exposure, min_exposure,
+ max_exposure);
+
+ __v4l2_ctrl_modify_range(imx283->exposure, min_exposure,
+ max_exposure, 1, current_exposure);
+ }
+
+ /*
+ * Applying V4L2 control value only happens
+ * when power is up for streaming
+ */
+ if (!pm_runtime_get_if_active(imx283->dev, true))
+ return 0;
+
+ switch (ctrl->id) {
+ case V4L2_CID_EXPOSURE:
+ shr = imx283_shr(imx283, mode, ctrl->val);
+ dev_dbg(imx283->dev, "V4L2_CID_EXPOSURE : %d - SHR: %lld\n",
+ ctrl->val, shr);
+ ret = cci_write(imx283->cci, IMX283_REG_SHR, shr, NULL);
+ break;
+
+ case V4L2_CID_HBLANK:
+ pixel_rate = imx283_pixel_rate(imx283, mode);
+ imx283->hmax = imx283_internal_clock(pixel_rate, mode->width + ctrl->val);
+ dev_dbg(imx283->dev, "V4L2_CID_HBLANK : %d HMAX : %u\n",
+ ctrl->val, imx283->hmax);
+ ret = cci_write(imx283->cci, IMX283_REG_HMAX, imx283->hmax, NULL);
+ break;
+
+ case V4L2_CID_VBLANK:
+ imx283->vmax = mode->height + ctrl->val;
+ dev_dbg(imx283->dev, "V4L2_CID_VBLANK : %d VMAX : %u\n",
+ ctrl->val, imx283->vmax);
+ ret = cci_write(imx283->cci, IMX283_REG_VMAX, imx283->vmax, NULL);
+ break;
+
+ case V4L2_CID_ANALOGUE_GAIN:
+ ret = cci_write(imx283->cci, IMX283_REG_ANALOG_GAIN, ctrl->val, NULL);
+ break;
+
+ case V4L2_CID_DIGITAL_GAIN:
+ ret = cci_write(imx283->cci, IMX283_REG_DIGITAL_GAIN, ctrl->val, NULL);
+ break;
+
+ case V4L2_CID_VFLIP:
+ /*
+ * VFLIP is managed by BIT(0) of IMX283_REG_HTRIMMING address, hence
+ * both need to be set simultaneously.
+ */
+ if (ctrl->val) {
+ cci_write(imx283->cci, IMX283_REG_HTRIMMING,
+ IMX283_HTRIMMING_EN | IMX283_MDVREV, &ret);
+ } else {
+ cci_write(imx283->cci, IMX283_REG_HTRIMMING,
+ IMX283_HTRIMMING_EN, &ret);
+ }
+ break;
+
+ case V4L2_CID_TEST_PATTERN:
+ ret = imx283_update_test_pattern(imx283, ctrl->val);
+ break;
+
+ default:
+ dev_err(imx283->dev, "ctrl(id:0x%x, val:0x%x) is not handled\n",
+ ctrl->id, ctrl->val);
+ break;
+ }
+
+ pm_runtime_put(imx283->dev);
+
+ return ret;
+}
+
+static const struct v4l2_ctrl_ops imx283_ctrl_ops = {
+ .s_ctrl = imx283_set_ctrl,
+};
+
+static int imx283_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->index >= ARRAY_SIZE(imx283_mbus_codes))
+ return -EINVAL;
+
+ code->code = imx283_mbus_codes[code->index];
+
+ return 0;
+}
+
+static int imx283_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ const struct imx283_mode *mode_list;
+ unsigned int num_modes;
+
+ get_mode_table(fse->code, &mode_list, &num_modes);
+
+ if (fse->index >= num_modes)
+ return -EINVAL;
+
+ fse->min_width = mode_list[fse->index].width;
+ fse->max_width = fse->min_width;
+ fse->min_height = mode_list[fse->index].height;
+ fse->max_height = fse->min_height;
+
+ return 0;
+}
+
+static void imx283_update_image_pad_format(struct imx283 *imx283,
+ const struct imx283_mode *mode,
+ struct v4l2_mbus_framefmt *format)
+{
+ format->width = mode->width;
+ format->height = mode->height;
+ format->field = V4L2_FIELD_NONE;
+ format->colorspace = V4L2_COLORSPACE_RAW;
+ format->ycbcr_enc = V4L2_YCBCR_ENC_601;
+ format->quantization = V4L2_QUANTIZATION_FULL_RANGE;
+ format->xfer_func = V4L2_XFER_FUNC_NONE;
+}
+
+static int imx283_init_state(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct imx283 *imx283 = to_imx283(sd);
+ struct v4l2_mbus_framefmt *format;
+ const struct imx283_mode *mode;
+ struct v4l2_rect *crop;
+
+ /* Initialize try_fmt */
+ format = v4l2_subdev_state_get_format(state, IMAGE_PAD);
+
+ mode = &supported_modes_12bit[0];
+ format->code = MEDIA_BUS_FMT_SRGGB12_1X12;
+ imx283_update_image_pad_format(imx283, mode, format);
+
+ /* Initialize crop rectangle to mode default */
+ crop = v4l2_subdev_state_get_crop(state, IMAGE_PAD);
+ *crop = mode->crop;
+
+ return 0;
+}
+
+static void imx283_set_framing_limits(struct imx283 *imx283,
+ const struct imx283_mode *mode)
+{
+ u64 pixel_rate = imx283_pixel_rate(imx283, mode);
+ u64 min_hblank, max_hblank, def_hblank;
+
+ /* Initialise hmax and vmax for exposure calculations */
+ imx283->hmax = imx283_internal_clock(pixel_rate, mode->default_hmax);
+ imx283->vmax = mode->default_vmax;
+
+ /*
+ * Horizontal Blanking
+ * Convert the HMAX_MAX (72MHz) to Pixel rate values for HBLANK_MAX
+ */
+ min_hblank = mode->min_hmax - mode->width;
+ max_hblank = imx283_iclk_to_pix(pixel_rate, IMX283_HMAX_MAX) - mode->width;
+ def_hblank = mode->default_hmax - mode->width;
+ __v4l2_ctrl_modify_range(imx283->hblank, min_hblank, max_hblank, 1,
+ def_hblank);
+ __v4l2_ctrl_s_ctrl(imx283->hblank, def_hblank);
+
+ /* Vertical Blanking */
+ __v4l2_ctrl_modify_range(imx283->vblank, mode->min_vmax - mode->height,
+ IMX283_VMAX_MAX - mode->height, 1,
+ mode->default_vmax - mode->height);
+ __v4l2_ctrl_s_ctrl(imx283->vblank, mode->default_vmax - mode->height);
+}
+
+static int imx283_set_pad_format(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_format *fmt)
+{
+ struct v4l2_mbus_framefmt *format;
+ const struct imx283_mode *mode;
+ struct imx283 *imx283 = to_imx283(sd);
+ const struct imx283_mode *mode_list;
+ unsigned int num_modes;
+
+ get_mode_table(fmt->format.code, &mode_list, &num_modes);
+
+ mode = v4l2_find_nearest_size(mode_list, num_modes, width, height,
+ fmt->format.width, fmt->format.height);
+
+ fmt->format.width = mode->width;
+ fmt->format.height = mode->height;
+ fmt->format.field = V4L2_FIELD_NONE;
+ fmt->format.colorspace = V4L2_COLORSPACE_RAW;
+ fmt->format.ycbcr_enc = V4L2_YCBCR_ENC_601;
+ fmt->format.quantization = V4L2_QUANTIZATION_FULL_RANGE;
+ fmt->format.xfer_func = V4L2_XFER_FUNC_NONE;
+
+ format = v4l2_subdev_state_get_format(sd_state, 0);
+
+ if (fmt->which == V4L2_SUBDEV_FORMAT_ACTIVE)
+ imx283_set_framing_limits(imx283, mode);
+
+ *format = fmt->format;
+
+ return 0;
+}
+
+static int imx283_standby_cancel(struct imx283 *imx283)
+{
+ unsigned int link_freq_idx;
+ int ret = 0;
+
+ cci_write(imx283->cci, IMX283_REG_STANDBY,
+ IMX283_STBLOGIC | IMX283_STBDV, &ret);
+
+ /* Configure PLL clocks based on the xclk */
+ cci_multi_reg_write(imx283->cci, imx283->freq->regs,
+ imx283->freq->reg_count, &ret);
+
+ dev_dbg(imx283->dev, "Using clk freq %ld MHz",
+ imx283->freq->mhz / HZ_PER_MHZ);
+
+ /* Initialise communication */
+ cci_write(imx283->cci, IMX283_REG_PLSTMG08, IMX283_PLSTMG08_VAL, &ret);
+ cci_write(imx283->cci, IMX283_REG_PLSTMG02, IMX283_PLSTMG02_VAL, &ret);
+
+ /* Enable PLL */
+ cci_write(imx283->cci, IMX283_REG_STBPL, IMX283_STBPL_NORMAL, &ret);
+
+ /* Configure the MIPI link speed */
+ link_freq_idx = __ffs(imx283->link_freq_bitmap);
+ cci_multi_reg_write(imx283->cci, link_freq_reglist[link_freq_idx].regs,
+ link_freq_reglist[link_freq_idx].num_of_regs,
+ &ret);
+
+ /* 1st Stabilisation period of 1 ms or more */
+ usleep_range(1000, 2000);
+
+ /* Activate */
+ cci_write(imx283->cci, IMX283_REG_STANDBY, IMX283_ACTIVE, &ret);
+
+ /* 2nd Stabilisation period of 19ms or more */
+ usleep_range(19000, 20000);
+
+ cci_write(imx283->cci, IMX283_REG_CLAMP, IMX283_CLPSQRST, &ret);
+ cci_write(imx283->cci, IMX283_REG_XMSTA, 0, &ret);
+ cci_write(imx283->cci, IMX283_REG_SYNCDRV, IMX283_SYNCDRV_XHS_XVS, &ret);
+
+ return ret;
+}
+
+/* Start streaming */
+static int imx283_start_streaming(struct imx283 *imx283,
+ struct v4l2_subdev_state *state)
+{
+ const struct imx283_readout_mode *readout;
+ const struct imx283_mode *mode;
+ const struct v4l2_mbus_framefmt *fmt;
+ const struct imx283_mode *mode_list;
+ unsigned int num_modes;
+ u32 v_widcut;
+ s32 v_pos;
+ u32 write_v_size;
+ u32 y_out_size;
+ int ret = 0;
+
+ fmt = v4l2_subdev_state_get_format(state, 0);
+ get_mode_table(fmt->code, &mode_list, &num_modes);
+ mode = v4l2_find_nearest_size(mode_list, num_modes, width, height,
+ fmt->width, fmt->height);
+
+ ret = imx283_standby_cancel(imx283);
+ if (ret) {
+ dev_err(imx283->dev, "failed to cancel standby\n");
+ return ret;
+ }
+
+ /*
+ * Set the readout mode registers.
+ * MDSEL3 and MDSEL4 are updated to enable Arbitrary Vertical Cropping.
+ */
+ readout = &imx283_readout_modes[mode->mode];
+ cci_write(imx283->cci, IMX283_REG_MDSEL1, readout->mdsel1, &ret);
+ cci_write(imx283->cci, IMX283_REG_MDSEL2, readout->mdsel2, &ret);
+ cci_write(imx283->cci, IMX283_REG_MDSEL3,
+ readout->mdsel3 | IMX283_MDSEL3_VCROP_EN, &ret);
+ cci_write(imx283->cci, IMX283_REG_MDSEL4,
+ readout->mdsel4 | IMX283_MDSEL4_VCROP_EN, &ret);
+
+ /* Mode 1S specific entries from the Readout Drive Mode Tables */
+ if (mode->mode == IMX283_MODE_1S) {
+ cci_write(imx283->cci, IMX283_REG_MDSEL7, 0x01, &ret);
+ cci_write(imx283->cci, IMX283_REG_MDSEL18, 0x1098, &ret);
+ }
+
+ if (ret) {
+ dev_err(imx283->dev, "failed to set readout\n");
+ return ret;
+ }
+
+ /* Initialise SVR. Unsupported for now - Always 0 */
+ cci_write(imx283->cci, IMX283_REG_SVR, 0x00, &ret);
+
+ dev_dbg(imx283->dev, "Mode: Size %d x %d\n", mode->width, mode->height);
+ dev_dbg(imx283->dev, "Analogue Crop (in the mode) %d,%d %dx%d\n",
+ mode->crop.left,
+ mode->crop.top,
+ mode->crop.width,
+ mode->crop.height);
+
+ y_out_size = mode->crop.height / mode->vbin_ratio;
+ write_v_size = y_out_size + mode->vertical_ob;
+ /*
+ * cropping start position = (VWINPOS – Vst) × 2
+ * cropping width = Veff – (VWIDCUT – Vct) × 2
+ */
+ v_pos = imx283->vflip->val ?
+ ((-mode->crop.top / mode->vbin_ratio) / 2) + mode->vst :
+ ((mode->crop.top / mode->vbin_ratio) / 2) + mode->vst;
+ v_widcut = ((mode->veff - y_out_size) / 2) + mode->vct;
+
+ cci_write(imx283->cci, IMX283_REG_Y_OUT_SIZE, y_out_size, &ret);
+ cci_write(imx283->cci, IMX283_REG_WRITE_VSIZE, write_v_size, &ret);
+ cci_write(imx283->cci, IMX283_REG_VWIDCUT, v_widcut, &ret);
+ cci_write(imx283->cci, IMX283_REG_VWINPOS, v_pos, &ret);
+
+ cci_write(imx283->cci, IMX283_REG_OB_SIZE_V, mode->vertical_ob, &ret);
+
+ /* TODO: Validate mode->crop is fully contained within imx283_native_area */
+ cci_write(imx283->cci, IMX283_REG_HTRIMMING_START, mode->crop.left, &ret);
+ cci_write(imx283->cci, IMX283_REG_HTRIMMING_END,
+ mode->crop.left + mode->crop.width, &ret);
+
+ /* Disable embedded data */
+ cci_write(imx283->cci, IMX283_REG_EBD_X_OUT_SIZE, 0, &ret);
+
+ /* Apply customized values from controls (HMAX/VMAX/SHR) */
+ ret = __v4l2_ctrl_handler_setup(imx283->sd.ctrl_handler);
+
+ return ret;
+}
+
+static int imx283_enable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct imx283 *imx283 = to_imx283(sd);
+ int ret;
+
+ if (pad != IMAGE_PAD)
+ return -EINVAL;
+
+ ret = pm_runtime_get_sync(imx283->dev);
+ if (ret < 0) {
+ pm_runtime_put_noidle(imx283->dev);
+ return ret;
+ }
+
+ ret = imx283_start_streaming(imx283, state);
+ if (ret)
+ goto err_rpm_put;
+
+ return 0;
+
+err_rpm_put:
+ pm_runtime_mark_last_busy(imx283->dev);
+ pm_runtime_put_autosuspend(imx283->dev);
+
+ return ret;
+}
+
+static int imx283_disable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct imx283 *imx283 = to_imx283(sd);
+ int ret;
+
+ if (pad != IMAGE_PAD)
+ return -EINVAL;
+
+ ret = cci_write(imx283->cci, IMX283_REG_STANDBY, IMX283_STBLOGIC, NULL);
+ if (ret)
+ dev_err(imx283->dev, "Failed to stop stream\n");
+
+ pm_runtime_mark_last_busy(imx283->dev);
+ pm_runtime_put_autosuspend(imx283->dev);
+
+ return ret;
+}
+
+/* Power/clock management functions */
+static int imx283_power_on(struct imx283 *imx283)
+{
+ int ret;
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(imx283_supply_name),
+ imx283->supplies);
+ if (ret) {
+ dev_err(imx283->dev, "failed to enable regulators\n");
+ return ret;
+ }
+
+ ret = clk_prepare_enable(imx283->xclk);
+ if (ret) {
+ dev_err(imx283->dev, "failed to enable clock\n");
+ goto reg_off;
+ }
+
+ gpiod_set_value_cansleep(imx283->reset_gpio, 0);
+
+ usleep_range(IMX283_XCLR_MIN_DELAY_US,
+ IMX283_XCLR_MIN_DELAY_US + IMX283_XCLR_DELAY_RANGE_US);
+
+ return 0;
+
+reg_off:
+ regulator_bulk_disable(ARRAY_SIZE(imx283_supply_name), imx283->supplies);
+ return ret;
+}
+
+static int imx283_power_off(struct imx283 *imx283)
+{
+ gpiod_set_value_cansleep(imx283->reset_gpio, 1);
+ regulator_bulk_disable(ARRAY_SIZE(imx283_supply_name), imx283->supplies);
+ clk_disable_unprepare(imx283->xclk);
+
+ return 0;
+}
+
+static int imx283_runtime_resume(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct imx283 *imx283 = to_imx283(sd);
+
+ return imx283_power_on(imx283);
+}
+
+static int imx283_runtime_suspend(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct imx283 *imx283 = to_imx283(sd);
+
+ imx283_power_off(imx283);
+
+ return 0;
+}
+
+static int imx283_get_regulators(struct imx283 *imx283)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(imx283_supply_name); i++)
+ imx283->supplies[i].supply = imx283_supply_name[i];
+
+ return devm_regulator_bulk_get(imx283->dev,
+ ARRAY_SIZE(imx283_supply_name),
+ imx283->supplies);
+}
+
+/* Verify chip ID */
+static int imx283_identify_module(struct imx283 *imx283)
+{
+ int ret;
+ u64 val;
+
+ ret = cci_read(imx283->cci, IMX283_REG_CHIP_ID, &val, NULL);
+ if (ret) {
+ dev_err(imx283->dev, "failed to read chip id %x, with error %d\n",
+ IMX283_CHIP_ID, ret);
+ return ret;
+ }
+
+ if (val != IMX283_CHIP_ID) {
+ dev_err(imx283->dev, "chip id mismatch: %x!=%llx\n",
+ IMX283_CHIP_ID, val);
+ return -EIO;
+ }
+
+ return 0;
+}
+
+static int imx283_get_selection(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_selection *sel)
+{
+ switch (sel->target) {
+ case V4L2_SEL_TGT_CROP: {
+ sel->r = *v4l2_subdev_state_get_crop(sd_state, 0);
+ return 0;
+ }
+
+ case V4L2_SEL_TGT_NATIVE_SIZE:
+ sel->r = imx283_native_area;
+ return 0;
+
+ case V4L2_SEL_TGT_CROP_DEFAULT:
+ case V4L2_SEL_TGT_CROP_BOUNDS:
+ sel->r = imx283_active_area;
+ return 0;
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct v4l2_subdev_core_ops imx283_core_ops = {
+ .subscribe_event = v4l2_ctrl_subdev_subscribe_event,
+ .unsubscribe_event = v4l2_event_subdev_unsubscribe,
+};
+
+static const struct v4l2_subdev_video_ops imx283_video_ops = {
+ .s_stream = v4l2_subdev_s_stream_helper,
+};
+
+static const struct v4l2_subdev_pad_ops imx283_pad_ops = {
+ .enum_mbus_code = imx283_enum_mbus_code,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .set_fmt = imx283_set_pad_format,
+ .get_selection = imx283_get_selection,
+ .enum_frame_size = imx283_enum_frame_size,
+ .enable_streams = imx283_enable_streams,
+ .disable_streams = imx283_disable_streams,
+};
+
+static const struct v4l2_subdev_internal_ops imx283_internal_ops = {
+ .init_state = imx283_init_state,
+};
+
+static const struct v4l2_subdev_ops imx283_subdev_ops = {
+ .core = &imx283_core_ops,
+ .video = &imx283_video_ops,
+ .pad = &imx283_pad_ops,
+};
+
+/* Initialize control handlers */
+static int imx283_init_controls(struct imx283 *imx283)
+{
+ struct v4l2_ctrl_handler *ctrl_hdlr;
+ struct v4l2_fwnode_device_properties props;
+ struct v4l2_ctrl *link_freq;
+ const struct imx283_mode *mode = &supported_modes_12bit[0];
+ u64 min_hblank, max_hblank, def_hblank;
+ u64 pixel_rate;
+ int ret;
+
+ ctrl_hdlr = &imx283->ctrl_handler;
+ ret = v4l2_ctrl_handler_init(ctrl_hdlr, 16);
+ if (ret)
+ return ret;
+
+ /*
+ * Create the controls here, but mode specific limits are setup
+ * in the imx283_set_framing_limits() call below.
+ */
+
+ /* By default, PIXEL_RATE is read only */
+ pixel_rate = imx283_pixel_rate(imx283, mode);
+ v4l2_ctrl_new_std(ctrl_hdlr, &imx283_ctrl_ops,
+ V4L2_CID_PIXEL_RATE, pixel_rate,
+ pixel_rate, 1, pixel_rate);
+
+ link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr, &imx283_ctrl_ops,
+ V4L2_CID_LINK_FREQ,
+ __fls(imx283->link_freq_bitmap),
+ __ffs(imx283->link_freq_bitmap),
+ link_frequencies);
+ if (link_freq)
+ link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+
+ /* Initialise vblank/hblank/exposure based on the current mode. */
+ imx283->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx283_ctrl_ops,
+ V4L2_CID_VBLANK,
+ mode->min_vmax - mode->height,
+ IMX283_VMAX_MAX, 1,
+ mode->default_vmax - mode->height);
+
+ min_hblank = mode->min_hmax - mode->width;
+ max_hblank = imx283_iclk_to_pix(pixel_rate, IMX283_HMAX_MAX) - mode->width;
+ def_hblank = mode->default_hmax - mode->width;
+ imx283->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx283_ctrl_ops,
+ V4L2_CID_HBLANK, min_hblank, max_hblank,
+ 1, def_hblank);
+
+ imx283->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &imx283_ctrl_ops,
+ V4L2_CID_EXPOSURE,
+ IMX283_EXPOSURE_MIN,
+ IMX283_EXPOSURE_MAX,
+ IMX283_EXPOSURE_STEP,
+ IMX283_EXPOSURE_DEFAULT);
+
+ v4l2_ctrl_new_std(ctrl_hdlr, &imx283_ctrl_ops, V4L2_CID_ANALOGUE_GAIN,
+ IMX283_ANA_GAIN_MIN, IMX283_ANA_GAIN_MAX,
+ IMX283_ANA_GAIN_STEP, IMX283_ANA_GAIN_DEFAULT);
+
+ v4l2_ctrl_new_std(ctrl_hdlr, &imx283_ctrl_ops, V4L2_CID_DIGITAL_GAIN,
+ IMX283_DGTL_GAIN_MIN, IMX283_DGTL_GAIN_MAX,
+ IMX283_DGTL_GAIN_STEP, IMX283_DGTL_GAIN_DEFAULT);
+
+ imx283->vflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx283_ctrl_ops, V4L2_CID_VFLIP,
+ 0, 1, 1, 0);
+ if (imx283->vflip)
+ imx283->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT;
+
+ v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &imx283_ctrl_ops,
+ V4L2_CID_TEST_PATTERN,
+ ARRAY_SIZE(imx283_tpg_menu) - 1,
+ 0, 0, imx283_tpg_menu);
+
+ if (ctrl_hdlr->error) {
+ ret = ctrl_hdlr->error;
+ dev_err(imx283->dev, "control init failed (%d)\n", ret);
+ goto error;
+ }
+
+ ret = v4l2_fwnode_device_parse(imx283->dev, &props);
+ if (ret)
+ goto error;
+
+ ret = v4l2_ctrl_new_fwnode_properties(ctrl_hdlr, &imx283_ctrl_ops,
+ &props);
+ if (ret)
+ goto error;
+
+ imx283->sd.ctrl_handler = ctrl_hdlr;
+
+ mutex_lock(imx283->ctrl_handler.lock);
+
+ /* Setup exposure and frame/line length limits. */
+ imx283_set_framing_limits(imx283, mode);
+
+ mutex_unlock(imx283->ctrl_handler.lock);
+
+ return 0;
+
+error:
+ v4l2_ctrl_handler_free(ctrl_hdlr);
+
+ return ret;
+}
+
+static int imx283_parse_endpoint(struct imx283 *imx283)
+{
+ struct fwnode_handle *fwnode;
+ struct v4l2_fwnode_endpoint bus_cfg = {
+ .bus_type = V4L2_MBUS_CSI2_DPHY
+ };
+ struct fwnode_handle *ep;
+ int ret;
+
+ fwnode = dev_fwnode(imx283->dev);
+ ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
+ if (!ep) {
+ dev_err(imx283->dev, "Failed to get next endpoint\n");
+ return -ENXIO;
+ }
+
+ ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
+ fwnode_handle_put(ep);
+ if (ret)
+ return ret;
+
+ if (bus_cfg.bus.mipi_csi2.num_data_lanes != 4) {
+ dev_err(imx283->dev,
+ "number of CSI2 data lanes %d is not supported\n",
+ bus_cfg.bus.mipi_csi2.num_data_lanes);
+ ret = -EINVAL;
+ goto done_endpoint_free;
+ }
+
+ ret = v4l2_link_freq_to_bitmap(imx283->dev, bus_cfg.link_frequencies,
+ bus_cfg.nr_of_link_frequencies,
+ link_frequencies, ARRAY_SIZE(link_frequencies),
+ &imx283->link_freq_bitmap);
+
+done_endpoint_free:
+ v4l2_fwnode_endpoint_free(&bus_cfg);
+
+ return ret;
+};
+
+static int imx283_probe(struct i2c_client *client)
+{
+ struct imx283 *imx283;
+ unsigned int i;
+ unsigned int xclk_freq;
+ int ret;
+
+ imx283 = devm_kzalloc(&client->dev, sizeof(*imx283), GFP_KERNEL);
+ if (!imx283)
+ return -ENOMEM;
+
+ imx283->dev = &client->dev;
+
+ v4l2_i2c_subdev_init(&imx283->sd, client, &imx283_subdev_ops);
+
+ imx283->cci = devm_cci_regmap_init_i2c(client, 16);
+ if (IS_ERR(imx283->cci)) {
+ ret = PTR_ERR(imx283->cci);
+ dev_err(imx283->dev, "failed to initialize CCI: %d\n", ret);
+ return ret;
+ }
+
+ /* Get system clock (xclk) */
+ imx283->xclk = devm_clk_get(imx283->dev, NULL);
+ if (IS_ERR(imx283->xclk)) {
+ return dev_err_probe(imx283->dev, PTR_ERR(imx283->xclk),
+ "failed to get xclk\n");
+ }
+
+ xclk_freq = clk_get_rate(imx283->xclk);
+ for (i = 0; i < ARRAY_SIZE(imx283_frequencies); i++) {
+ if (xclk_freq == imx283_frequencies[i].mhz) {
+ imx283->freq = &imx283_frequencies[i];
+ break;
+ }
+ }
+ if (!imx283->freq) {
+ dev_err(imx283->dev, "xclk frequency unsupported: %d Hz\n", xclk_freq);
+ return -EINVAL;
+ }
+
+ ret = imx283_get_regulators(imx283);
+ if (ret) {
+ return dev_err_probe(imx283->dev, ret,
+ "failed to get regulators\n");
+ }
+
+ ret = imx283_parse_endpoint(imx283);
+ if (ret) {
+ dev_err(imx283->dev, "failed to parse endpoint configuration\n");
+ return ret;
+ }
+
+ /* Request optional enable pin */
+ imx283->reset_gpio = devm_gpiod_get_optional(imx283->dev, "reset",
+ GPIOD_OUT_LOW);
+ if (IS_ERR(imx283->reset_gpio))
+ return dev_err_probe(imx283->dev, PTR_ERR(imx283->reset_gpio),
+ "failed to get reset GPIO\n");
+
+ /*
+ * The sensor must be powered for imx283_identify_module()
+ * to be able to read the CHIP_ID register
+ */
+ ret = imx283_power_on(imx283);
+ if (ret)
+ return ret;
+
+ ret = imx283_identify_module(imx283);
+ if (ret)
+ goto error_power_off;
+
+ /*
+ * Enable runtime PM with autosuspend. As the device has been powered
+ * manually, mark it as active, and increase the usage count without
+ * resuming the device.
+ */
+ pm_runtime_set_active(imx283->dev);
+ pm_runtime_get_noresume(imx283->dev);
+ pm_runtime_enable(imx283->dev);
+ pm_runtime_set_autosuspend_delay(imx283->dev, 1000);
+ pm_runtime_use_autosuspend(imx283->dev);
+
+ /* This needs the pm runtime to be registered. */
+ ret = imx283_init_controls(imx283);
+ if (ret)
+ goto error_pm;
+
+ /* Initialize subdev */
+ imx283->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE |
+ V4L2_SUBDEV_FL_HAS_EVENTS;
+ imx283->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+ imx283->sd.internal_ops = &imx283_internal_ops;
+
+ /* Initialize source pads */
+ imx283->pad.flags = MEDIA_PAD_FL_SOURCE;
+
+ ret = media_entity_pads_init(&imx283->sd.entity, 1, &imx283->pad);
+ if (ret) {
+ dev_err(imx283->dev, "failed to init entity pads: %d\n", ret);
+ goto error_handler_free;
+ }
+
+ imx283->sd.state_lock = imx283->ctrl_handler.lock;
+ ret = v4l2_subdev_init_finalize(&imx283->sd);
+ if (ret < 0) {
+ dev_err(imx283->dev, "subdev init error: %d\n", ret);
+ goto error_media_entity;
+ }
+
+ ret = v4l2_async_register_subdev_sensor(&imx283->sd);
+ if (ret < 0) {
+ dev_err(imx283->dev, "failed to register sensor sub-device: %d\n", ret);
+ goto error_subdev_cleanup;
+ }
+
+ /*
+ * Decrease the PM usage count. The device will get suspended after the
+ * autosuspend delay, turning the power off.
+ */
+ pm_runtime_mark_last_busy(imx283->dev);
+ pm_runtime_put_autosuspend(imx283->dev);
+
+ return 0;
+
+error_subdev_cleanup:
+ v4l2_subdev_cleanup(&imx283->sd);
+
+error_media_entity:
+ media_entity_cleanup(&imx283->sd.entity);
+
+error_handler_free:
+ v4l2_ctrl_handler_free(imx283->sd.ctrl_handler);
+
+error_pm:
+ pm_runtime_disable(imx283->dev);
+ pm_runtime_set_suspended(imx283->dev);
+error_power_off:
+ imx283_power_off(imx283);
+
+ return ret;
+}
+
+static void imx283_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct imx283 *imx283 = to_imx283(sd);
+
+ v4l2_async_unregister_subdev(sd);
+ v4l2_subdev_cleanup(&imx283->sd);
+ media_entity_cleanup(&sd->entity);
+ v4l2_ctrl_handler_free(imx283->sd.ctrl_handler);
+
+ pm_runtime_disable(imx283->dev);
+ if (!pm_runtime_status_suspended(imx283->dev))
+ imx283_power_off(imx283);
+ pm_runtime_set_suspended(imx283->dev);
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(imx283_pm_ops, imx283_runtime_suspend,
+ imx283_runtime_resume, NULL);
+
+static const struct of_device_id imx283_dt_ids[] = {
+ { .compatible = "sony,imx283" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx283_dt_ids);
+
+static struct i2c_driver imx283_i2c_driver = {
+ .driver = {
+ .name = "imx283",
+ .pm = pm_ptr(&imx283_pm_ops),
+ .of_match_table = imx283_dt_ids,
+ },
+ .probe = imx283_probe,
+ .remove = imx283_remove,
+};
+module_i2c_driver(imx283_i2c_driver);
+
+MODULE_AUTHOR("Will Whang <will@willwhang.com>");
+MODULE_AUTHOR("Kieran Bingham <kieran.bingham@ideasonboard.com>");
+MODULE_AUTHOR("Umang Jain <umang.jain@ideasonboard.com>");
+MODULE_DESCRIPTION("Sony IMX283 Sensor Driver");
+MODULE_LICENSE("GPL");