[v6,2/2] pwm: sophgo: add pwm support for Sophgo CV1800 SoC

Commit Message

Jingbao Qiu April 6, 2024, 6:34 a.m. UTC

Implement the PWM driver for CV1800.

Signed-off-by: Jingbao Qiu <[e-mail]>
---
 drivers/pwm/Kconfig      |  10 ++
 drivers/pwm/Makefile     |   1 +
 drivers/pwm/pwm-cv1800.c | 296 +++++++++++++++++++++++++++++++++++++++
 3 files changed, 307 insertions(+)
 create mode 100644 drivers/pwm/pwm-cv1800.c

Comments

Uwe Kleine-König April 29, 2024, 2:54 p.m. UTC | #1

Hello,

On Sat, Apr 06, 2024 at 02:34:13PM +0800, Jingbao Qiu wrote:
> Implement the PWM driver for CV1800.
> 
> Signed-off-by: Jingbao Qiu <[e-mail]>
> ---
>  drivers/pwm/Kconfig      |  10 ++
>  drivers/pwm/Makefile     |   1 +
>  drivers/pwm/pwm-cv1800.c | 296 +++++++++++++++++++++++++++++++++++++++
>  3 files changed, 307 insertions(+)
>  create mode 100644 drivers/pwm/pwm-cv1800.c
> 
> diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> index 1dd7921194f5..3869ca022aeb 100644
> --- a/drivers/pwm/Kconfig
> +++ b/drivers/pwm/Kconfig
> @@ -182,6 +182,16 @@ config PWM_CROS_EC
>  	  PWM driver for exposing a PWM attached to the ChromeOS Embedded
>  	  Controller.
>  
> +config PWM_CV1800
> +	tristate "Sophgo CV1800 PWM driver"
> +	depends on ARCH_SOPHGO || COMPILE_TEST
> +	help
> +	  Generic PWM framework driver for the Sophgo CV1800 series
> +	  SoCs.
> +
> +	  To compile this driver as a module, build the dependecies
> +	  as modules, this will be called pwm-cv1800.
> +
>  config PWM_DWC_CORE
>  	tristate
>  	depends on HAS_IOMEM
> diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
> index 90913519f11a..6295e2259efc 100644
> --- a/drivers/pwm/Makefile
> +++ b/drivers/pwm/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_PWM_CLK)		+= pwm-clk.o
>  obj-$(CONFIG_PWM_CLPS711X)	+= pwm-clps711x.o
>  obj-$(CONFIG_PWM_CRC)		+= pwm-crc.o
>  obj-$(CONFIG_PWM_CROS_EC)	+= pwm-cros-ec.o
> +obj-$(CONFIG_PWM_CV1800)	+= pwm-cv1800.o
>  obj-$(CONFIG_PWM_DWC_CORE)	+= pwm-dwc-core.o
>  obj-$(CONFIG_PWM_DWC)		+= pwm-dwc.o
>  obj-$(CONFIG_PWM_EP93XX)	+= pwm-ep93xx.o
> diff --git a/drivers/pwm/pwm-cv1800.c b/drivers/pwm/pwm-cv1800.c
> new file mode 100644
> index 000000000000..37a6be3f63aa
> --- /dev/null
> +++ b/drivers/pwm/pwm-cv1800.c
> @@ -0,0 +1,296 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Sophgo CV1800 PWM driver
> + * Author: Jingbao Qiu <[e-mail]>
> + *
> + * Limitations:
> + * - It output low when PWM channel disabled.

Just to be sure: the output is low independant of the POLARITY register?

> + * - This pwm device supports dynamic loading of PWM parameters. When PWMSTART
> + *   is written from 0 to 1, the register value (HLPERIODn, PERIODn) will be
> + *   temporarily stored inside the PWM. If you want to dynamically change the
> + *   waveform during PWM output, after writing the new value to HLPERIODn and
> + *   PERIODn, write 1 and then 0 to PWMUPDATE[n] to make the new value effective.
> + * - Supports up to Rate/2 output, and the lowest is about Rate/(2^30-1).
> + * - By setting HLPERIODn to 0, can produce 100% duty cycle.
> + * - This hardware could support inverted polarity. By default, the value of the
> + *   POLARITY register is 0x0. This means that HLPERIOD represents the number
> + *   of low level beats.
> + * - This hardware supports input mode and output mode, implemented through the
> + *   Output-Enable/OE register. However, this driver has not yet implemented
> + *   capture callback.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/pwm.h>
> +#include <linux/regmap.h>
> +
> +#define PWM_CV1800_HLPERIOD_BASE    0x00
> +#define PWM_CV1800_PERIOD_BASE      0x04
> +#define PWM_CV1800_POLARITY         0x40
> +#define PWM_CV1800_START            0x44
> +#define PWM_CV1800_DONE             0x48
> +#define PWM_CV1800_UPDATE           0x4c
> +#define PWM_CV1800_OE               0xd0
> +
> +#define PWM_CV1800_HLPERIOD(n)      (PWM_CV1800_HLPERIOD_BASE + ((n)*0x08))
> +#define PWM_CV1800_PERIOD(n)        (PWM_CV1800_PERIOD_BASE + ((n)*0x08))
> +
> +#define PWM_CV1800_UPDATE_MASK(n)   (BIT(0) << (n))
> +#define PWM_CV1800_OE_MASK(n)       (BIT(0) << (n))
> +#define PWM_CV1800_START_MASK(n)    (BIT(0) << (n))
> +#define PWM_CV1800_POLARITY_MASK(n) (BIT(0) << (n))
> +
> +#define PWM_CV1800_MAXPERIOD        0x3fffffff
> +#define PWM_CV1800_MINPERIOD        2
> +#define PWM_CV1800_CHANNELS         4
> +#define PWM_CV1800_PERIOD_RESET     BIT(1)
> +#define PWM_CV1800_HLPERIOD_RESET   BIT(0)
> +#define PWM_CV1800_REG_DISABLE      0x00U
> +#define PWM_CV1800_REG_ENABLE(n)    (BIT(0) << (n))

BIT(n)?

> +
> +struct cv1800_pwm {
> +	struct regmap *map;
> +	struct clk *clk;
> +	unsigned long clk_rate;
> +};
> +
> +static inline struct cv1800_pwm *to_cv1800_pwm_dev(struct pwm_chip *chip)
> +{
> +	return pwmchip_get_drvdata(chip);
> +}
> +
> +static const struct regmap_config cv1800_pwm_regmap_config = {
> +	.reg_bits = 32,
> +	.val_bits = 32,
> +	.reg_stride = 4,
> +};
> +
> +static int cv1800_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm,
> +			     bool enable)
> +{
> +	struct cv1800_pwm *priv = to_cv1800_pwm_dev(chip);
> +	u32 pwm_enable, state;
> +
> +	regmap_read(priv->map, PWM_CV1800_START, &pwm_enable);
> +	pwm_enable &= PWM_CV1800_START_MASK(pwm->hwpwm);
> +
> +	/*
> +	 * If the parameters are changed during runtime, Register needs
> +	 * to be updated to take effect.
> +	 */
> +	if (pwm_enable && enable) {
> +		regmap_update_bits(priv->map, PWM_CV1800_UPDATE,
> +				   PWM_CV1800_UPDATE_MASK(pwm->hwpwm),
> +				   PWM_CV1800_REG_ENABLE(pwm->hwpwm));
> +		regmap_update_bits(priv->map, PWM_CV1800_UPDATE,
> +				   PWM_CV1800_UPDATE_MASK(pwm->hwpwm),
> +				   PWM_CV1800_REG_DISABLE);

I think using a plain 0 instead of PWM_CV1800_REG_DISABLE would be a tad
clearer.

> +	} else if (!pwm_enable && enable) {
> +		regmap_update_bits(priv->map, PWM_CV1800_START,
> +				   PWM_CV1800_START_MASK(pwm->hwpwm),
> +				   PWM_CV1800_REG_ENABLE(pwm->hwpwm));
> +	} else if (pwm_enable && !enable) {
> +		regmap_update_bits(priv->map, PWM_CV1800_START,
> +				   PWM_CV1800_START_MASK(pwm->hwpwm),
> +				   PWM_CV1800_REG_DISABLE);
> +	}
> +
> +	/* check and set OE/Output-Enable mode */
> +	regmap_read(priv->map, PWM_CV1800_OE, &state);
> +	state &= PWM_CV1800_OE_MASK(pwm->hwpwm);
> +
> +	if (state == PWM_CV1800_REG_DISABLE && enable)

Here I'd use:

	regmap_read(priv->map, PWM_CV1800_OE, &state);

	if ((state & BIT(pwm->hwpwm)) && enable)

> +		regmap_update_bits(priv->map, PWM_CV1800_OE,
> +				   PWM_CV1800_OE_MASK(pwm->hwpwm),
> +				   PWM_CV1800_REG_ENABLE(pwm->hwpwm));
> +
> +	return 0;
> +}
> +
> [...]
> +static int cv1800_pwm_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct cv1800_pwm *priv;
> +	struct pwm_chip *chip;
> +	void __iomem *base;
> +	int ret;
> +
> +	chip = devm_pwmchip_alloc(dev, PWM_CV1800_CHANNELS, sizeof(*priv));
> +	if (!chip)
> +		return PTR_ERR(chip);
> +	priv = to_cv1800_pwm_dev(chip);
> +
> +	base = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(base))
> +		return PTR_ERR(base);
> +
> +	priv->map = devm_regmap_init_mmio(&pdev->dev, base,
> +					  &cv1800_pwm_regmap_config);
> +	if (IS_ERR(priv->map))
> +		return PTR_ERR(priv->map);

devm_regmap_init_mmio() doesnt' emit an error message on failure, so
please add one here.

> +	priv->clk = devm_clk_get_enabled(&pdev->dev, NULL);
> +	if (IS_ERR(priv->clk))
> +		return dev_err_probe(&pdev->dev, PTR_ERR(priv->clk),
> +				     "clk not found\n");
> +

Best regards
Uwe

Jingbao Qiu April 30, 2024, 4:36 a.m. UTC | #2

Hi, Uwe

On Mon, Apr 29, 2024 at 10:54 PM Uwe Kleine-König
<[e-mail]> wrote:
>
> Hello,
>
> On Sat, Apr 06, 2024 at 02:34:13PM +0800, Jingbao Qiu wrote:
> > Implement the PWM driver for CV1800.
> >
> > Signed-off-by: Jingbao Qiu <[e-mail]>
> > ---
> >  drivers/pwm/Kconfig      |  10 ++
> >  drivers/pwm/Makefile     |   1 +
> >  drivers/pwm/pwm-cv1800.c | 296 +++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 307 insertions(+)
> >  create mode 100644 drivers/pwm/pwm-cv1800.c
> >
> > diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
> > index 1dd7921194f5..3869ca022aeb 100644
> > --- a/drivers/pwm/Kconfig
> > +++ b/drivers/pwm/Kconfig
> > @@ -182,6 +182,16 @@ config PWM_CROS_EC
> >         PWM driver for exposing a PWM attached to the ChromeOS Embedded
> >         Controller.
> >
> > +config PWM_CV1800
> > +     tristate "Sophgo CV1800 PWM driver"
> > +     depends on ARCH_SOPHGO || COMPILE_TEST
> > +     help
> > +       Generic PWM framework driver for the Sophgo CV1800 series
> > +       SoCs.
> > +
> > +       To compile this driver as a module, build the dependecies
> > +       as modules, this will be called pwm-cv1800.
> > +
> >  config PWM_DWC_CORE
> >       tristate
> >       depends on HAS_IOMEM
> > diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
> > index 90913519f11a..6295e2259efc 100644
> > --- a/drivers/pwm/Makefile
> > +++ b/drivers/pwm/Makefile
> > @@ -14,6 +14,7 @@ obj-$(CONFIG_PWM_CLK)               += pwm-clk.o
> >  obj-$(CONFIG_PWM_CLPS711X)   += pwm-clps711x.o
> >  obj-$(CONFIG_PWM_CRC)                += pwm-crc.o
> >  obj-$(CONFIG_PWM_CROS_EC)    += pwm-cros-ec.o
> > +obj-$(CONFIG_PWM_CV1800)     += pwm-cv1800.o
> >  obj-$(CONFIG_PWM_DWC_CORE)   += pwm-dwc-core.o
> >  obj-$(CONFIG_PWM_DWC)                += pwm-dwc.o
> >  obj-$(CONFIG_PWM_EP93XX)     += pwm-ep93xx.o
> > diff --git a/drivers/pwm/pwm-cv1800.c b/drivers/pwm/pwm-cv1800.c
> > new file mode 100644
> > index 000000000000..37a6be3f63aa
> > --- /dev/null
> > +++ b/drivers/pwm/pwm-cv1800.c
> > @@ -0,0 +1,296 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Sophgo CV1800 PWM driver
> > + * Author: Jingbao Qiu <[e-mail]>
> > + *
> > + * Limitations:
> > + * - It output low when PWM channel disabled.
>
> Just to be sure: the output is low independant of the POLARITY register?

When the value of the POLARITY register is 1, the PWM outputs a high level.
When the value of the POLARITY register is 0, the PWM output is low.
Should I make this point here?

>
> > + * - This pwm device supports dynamic loading of PWM parameters. When PWMSTART
> > + *   is written from 0 to 1, the register value (HLPERIODn, PERIODn) will be
> > + *   temporarily stored inside the PWM. If you want to dynamically change the
> > + *   waveform during PWM output, after writing the new value to HLPERIODn and
> > + *   PERIODn, write 1 and then 0 to PWMUPDATE[n] to make the new value effective.
> > + * - Supports up to Rate/2 output, and the lowest is about Rate/(2^30-1).
> > + * - By setting HLPERIODn to 0, can produce 100% duty cycle.
> > + * - This hardware could support inverted polarity. By default, the value of the
> > + *   POLARITY register is 0x0. This means that HLPERIOD represents the number
> > + *   of low level beats.
> > + * - This hardware supports input mode and output mode, implemented through the
> > + *   Output-Enable/OE register. However, this driver has not yet implemented
> > + *   capture callback.
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pwm.h>
> > +#include <linux/regmap.h>
> > +
> > +#define PWM_CV1800_HLPERIOD_BASE    0x00
> > +#define PWM_CV1800_PERIOD_BASE      0x04
> > +#define PWM_CV1800_POLARITY         0x40
> > +#define PWM_CV1800_START            0x44
> > +#define PWM_CV1800_DONE             0x48
> > +#define PWM_CV1800_UPDATE           0x4c
> > +#define PWM_CV1800_OE               0xd0
> > +
> > +#define PWM_CV1800_HLPERIOD(n)      (PWM_CV1800_HLPERIOD_BASE + ((n)*0x08))
> > +#define PWM_CV1800_PERIOD(n)        (PWM_CV1800_PERIOD_BASE + ((n)*0x08))
> > +
> > +#define PWM_CV1800_UPDATE_MASK(n)   (BIT(0) << (n))
> > +#define PWM_CV1800_OE_MASK(n)       (BIT(0) << (n))
> > +#define PWM_CV1800_START_MASK(n)    (BIT(0) << (n))
> > +#define PWM_CV1800_POLARITY_MASK(n) (BIT(0) << (n))
> > +
> > +#define PWM_CV1800_MAXPERIOD        0x3fffffff
> > +#define PWM_CV1800_MINPERIOD        2
> > +#define PWM_CV1800_CHANNELS         4
> > +#define PWM_CV1800_PERIOD_RESET     BIT(1)
> > +#define PWM_CV1800_HLPERIOD_RESET   BIT(0)
> > +#define PWM_CV1800_REG_DISABLE      0x00U
> > +#define PWM_CV1800_REG_ENABLE(n)    (BIT(0) << (n))
>
> BIT(n)?

yes, I will fix it.

>
> > +
> > +struct cv1800_pwm {
> > +     struct regmap *map;
> > +     struct clk *clk;
> > +     unsigned long clk_rate;
> > +};
> > +
> > +static inline struct cv1800_pwm *to_cv1800_pwm_dev(struct pwm_chip *chip)
> > +{
> > +     return pwmchip_get_drvdata(chip);
> > +}
> > +
> > +static const struct regmap_config cv1800_pwm_regmap_config = {
> > +     .reg_bits = 32,
> > +     .val_bits = 32,
> > +     .reg_stride = 4,
> > +};
> > +
> > +static int cv1800_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm,
> > +                          bool enable)
> > +{
> > +     struct cv1800_pwm *priv = to_cv1800_pwm_dev(chip);
> > +     u32 pwm_enable, state;
> > +
> > +     regmap_read(priv->map, PWM_CV1800_START, &pwm_enable);
> > +     pwm_enable &= PWM_CV1800_START_MASK(pwm->hwpwm);
> > +
> > +     /*
> > +      * If the parameters are changed during runtime, Register needs
> > +      * to be updated to take effect.
> > +      */
> > +     if (pwm_enable && enable) {
> > +             regmap_update_bits(priv->map, PWM_CV1800_UPDATE,
> > +                                PWM_CV1800_UPDATE_MASK(pwm->hwpwm),
> > +                                PWM_CV1800_REG_ENABLE(pwm->hwpwm));
> > +             regmap_update_bits(priv->map, PWM_CV1800_UPDATE,
> > +                                PWM_CV1800_UPDATE_MASK(pwm->hwpwm),
> > +                                PWM_CV1800_REG_DISABLE);
>
> I think using a plain 0 instead of PWM_CV1800_REG_DISABLE would be a tad
> clearer.

I will fix it.

>
> > +     } else if (!pwm_enable && enable) {
> > +             regmap_update_bits(priv->map, PWM_CV1800_START,
> > +                                PWM_CV1800_START_MASK(pwm->hwpwm),
> > +                                PWM_CV1800_REG_ENABLE(pwm->hwpwm));
> > +     } else if (pwm_enable && !enable) {
> > +             regmap_update_bits(priv->map, PWM_CV1800_START,
> > +                                PWM_CV1800_START_MASK(pwm->hwpwm),
> > +                                PWM_CV1800_REG_DISABLE);
> > +     }
> > +
> > +     /* check and set OE/Output-Enable mode */
> > +     regmap_read(priv->map, PWM_CV1800_OE, &state);
> > +     state &= PWM_CV1800_OE_MASK(pwm->hwpwm);
> > +
> > +     if (state == PWM_CV1800_REG_DISABLE && enable)
>
> Here I'd use:
>
>         regmap_read(priv->map, PWM_CV1800_OE, &state);
>
>         if ((state & BIT(pwm->hwpwm)) && enable)
>

I will fix it.

> > +             regmap_update_bits(priv->map, PWM_CV1800_OE,
> > +                                PWM_CV1800_OE_MASK(pwm->hwpwm),
> > +                                PWM_CV1800_REG_ENABLE(pwm->hwpwm));
> > +
> > +     return 0;
> > +}
> > +
> > [...]
> > +static int cv1800_pwm_probe(struct platform_device *pdev)
> > +{
> > +     struct device *dev = &pdev->dev;
> > +     struct cv1800_pwm *priv;
> > +     struct pwm_chip *chip;
> > +     void __iomem *base;
> > +     int ret;
> > +
> > +     chip = devm_pwmchip_alloc(dev, PWM_CV1800_CHANNELS, sizeof(*priv));
> > +     if (!chip)
> > +             return PTR_ERR(chip);
> > +     priv = to_cv1800_pwm_dev(chip);
> > +
> > +     base = devm_platform_ioremap_resource(pdev, 0);
> > +     if (IS_ERR(base))
> > +             return PTR_ERR(base);
> > +
> > +     priv->map = devm_regmap_init_mmio(&pdev->dev, base,
> > +                                       &cv1800_pwm_regmap_config);
> > +     if (IS_ERR(priv->map))
> > +             return PTR_ERR(priv->map);
>
> devm_regmap_init_mmio() doesnt' emit an error message on failure, so
> please add one here.

I will fix it.

Thank you for your suggestion.

Best regards
Jingbao Qiu

Uwe Kleine-König April 30, 2024, 8:06 a.m. UTC | #3

Hello Jingbao,

On Tue, Apr 30, 2024 at 12:36:56PM +0800, Jingbao Qiu wrote:
> On Mon, Apr 29, 2024 at 10:54 PM Uwe Kleine-König
> <[e-mail]> wrote:
> > On Sat, Apr 06, 2024 at 02:34:13PM +0800, Jingbao Qiu wrote:
> > > + * Limitations:
> > > + * - It output low when PWM channel disabled.
> >
> > Just to be sure: the output is low independant of the POLARITY register?
> 
> When the value of the POLARITY register is 1, the PWM outputs a high level.
> When the value of the POLARITY register is 0, the PWM output is low.
> Should I make this point here?

So that's: The hardware emits the inactive level when disabled.

Best regards
Uwe

Jingbao Qiu April 30, 2024, 12:47 p.m. UTC | #4

On Tue, Apr 30, 2024 at 4:06 PM Uwe Kleine-König
<[e-mail]> wrote:
>
> Hello Jingbao,
>
> On Tue, Apr 30, 2024 at 12:36:56PM +0800, Jingbao Qiu wrote:
> > On Mon, Apr 29, 2024 at 10:54 PM Uwe Kleine-König
> > <[e-mail]> wrote:
> > > On Sat, Apr 06, 2024 at 02:34:13PM +0800, Jingbao Qiu wrote:
> > > > + * Limitations:
> > > > + * - It output low when PWM channel disabled.
> > >
> > > Just to be sure: the output is low independant of the POLARITY register?
> >
> > When the value of the POLARITY register is 1, the PWM outputs a high level.
> > When the value of the POLARITY register is 0, the PWM output is low.
> > Should I make this point here?
>
> So that's: The hardware emits the inactive level when disabled.
>

I will do that.

Best regards
Jingbao Qiu

Patch

diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 1dd7921194f5..3869ca022aeb 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -182,6 +182,16 @@  config PWM_CROS_EC
 	  PWM driver for exposing a PWM attached to the ChromeOS Embedded
 	  Controller.
 
+config PWM_CV1800
+	tristate "Sophgo CV1800 PWM driver"
+	depends on ARCH_SOPHGO || COMPILE_TEST
+	help
+	  Generic PWM framework driver for the Sophgo CV1800 series
+	  SoCs.
+
+	  To compile this driver as a module, build the dependecies
+	  as modules, this will be called pwm-cv1800.
+
 config PWM_DWC_CORE
 	tristate
 	depends on HAS_IOMEM
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index 90913519f11a..6295e2259efc 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -14,6 +14,7 @@  obj-$(CONFIG_PWM_CLK)		+= pwm-clk.o
 obj-$(CONFIG_PWM_CLPS711X)	+= pwm-clps711x.o
 obj-$(CONFIG_PWM_CRC)		+= pwm-crc.o
 obj-$(CONFIG_PWM_CROS_EC)	+= pwm-cros-ec.o
+obj-$(CONFIG_PWM_CV1800)	+= pwm-cv1800.o
 obj-$(CONFIG_PWM_DWC_CORE)	+= pwm-dwc-core.o
 obj-$(CONFIG_PWM_DWC)		+= pwm-dwc.o
 obj-$(CONFIG_PWM_EP93XX)	+= pwm-ep93xx.o
diff --git a/drivers/pwm/pwm-cv1800.c b/drivers/pwm/pwm-cv1800.c
new file mode 100644
index 000000000000..37a6be3f63aa
--- /dev/null
+++ b/drivers/pwm/pwm-cv1800.c
@@ -0,0 +1,296 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Sophgo CV1800 PWM driver
+ * Author: Jingbao Qiu <[e-mail]>
+ *
+ * Limitations:
+ * - It output low when PWM channel disabled.
+ * - This pwm device supports dynamic loading of PWM parameters. When PWMSTART
+ *   is written from 0 to 1, the register value (HLPERIODn, PERIODn) will be
+ *   temporarily stored inside the PWM. If you want to dynamically change the
+ *   waveform during PWM output, after writing the new value to HLPERIODn and
+ *   PERIODn, write 1 and then 0 to PWMUPDATE[n] to make the new value effective.
+ * - Supports up to Rate/2 output, and the lowest is about Rate/(2^30-1).
+ * - By setting HLPERIODn to 0, can produce 100% duty cycle.
+ * - This hardware could support inverted polarity. By default, the value of the
+ *   POLARITY register is 0x0. This means that HLPERIOD represents the number
+ *   of low level beats.
+ * - This hardware supports input mode and output mode, implemented through the
+ *   Output-Enable/OE register. However, this driver has not yet implemented
+ *   capture callback.
+ */
+
+#include <linux/clk.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/regmap.h>
+
+#define PWM_CV1800_HLPERIOD_BASE    0x00
+#define PWM_CV1800_PERIOD_BASE      0x04
+#define PWM_CV1800_POLARITY         0x40
+#define PWM_CV1800_START            0x44
+#define PWM_CV1800_DONE             0x48
+#define PWM_CV1800_UPDATE           0x4c
+#define PWM_CV1800_OE               0xd0
+
+#define PWM_CV1800_HLPERIOD(n)      (PWM_CV1800_HLPERIOD_BASE + ((n)*0x08))
+#define PWM_CV1800_PERIOD(n)        (PWM_CV1800_PERIOD_BASE + ((n)*0x08))
+
+#define PWM_CV1800_UPDATE_MASK(n)   (BIT(0) << (n))
+#define PWM_CV1800_OE_MASK(n)       (BIT(0) << (n))
+#define PWM_CV1800_START_MASK(n)    (BIT(0) << (n))
+#define PWM_CV1800_POLARITY_MASK(n) (BIT(0) << (n))
+
+#define PWM_CV1800_MAXPERIOD        0x3fffffff
+#define PWM_CV1800_MINPERIOD        2
+#define PWM_CV1800_CHANNELS         4
+#define PWM_CV1800_PERIOD_RESET     BIT(1)
+#define PWM_CV1800_HLPERIOD_RESET   BIT(0)
+#define PWM_CV1800_REG_DISABLE      0x00U
+#define PWM_CV1800_REG_ENABLE(n)    (BIT(0) << (n))
+
+struct cv1800_pwm {
+	struct regmap *map;
+	struct clk *clk;
+	unsigned long clk_rate;
+};
+
+static inline struct cv1800_pwm *to_cv1800_pwm_dev(struct pwm_chip *chip)
+{
+	return pwmchip_get_drvdata(chip);
+}
+
+static const struct regmap_config cv1800_pwm_regmap_config = {
+	.reg_bits = 32,
+	.val_bits = 32,
+	.reg_stride = 4,
+};
+
+static int cv1800_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm,
+			     bool enable)
+{
+	struct cv1800_pwm *priv = to_cv1800_pwm_dev(chip);
+	u32 pwm_enable, state;
+
+	regmap_read(priv->map, PWM_CV1800_START, &pwm_enable);
+	pwm_enable &= PWM_CV1800_START_MASK(pwm->hwpwm);
+
+	/*
+	 * If the parameters are changed during runtime, Register needs
+	 * to be updated to take effect.
+	 */
+	if (pwm_enable && enable) {
+		regmap_update_bits(priv->map, PWM_CV1800_UPDATE,
+				   PWM_CV1800_UPDATE_MASK(pwm->hwpwm),
+				   PWM_CV1800_REG_ENABLE(pwm->hwpwm));
+		regmap_update_bits(priv->map, PWM_CV1800_UPDATE,
+				   PWM_CV1800_UPDATE_MASK(pwm->hwpwm),
+				   PWM_CV1800_REG_DISABLE);
+	} else if (!pwm_enable && enable) {
+		regmap_update_bits(priv->map, PWM_CV1800_START,
+				   PWM_CV1800_START_MASK(pwm->hwpwm),
+				   PWM_CV1800_REG_ENABLE(pwm->hwpwm));
+	} else if (pwm_enable && !enable) {
+		regmap_update_bits(priv->map, PWM_CV1800_START,
+				   PWM_CV1800_START_MASK(pwm->hwpwm),
+				   PWM_CV1800_REG_DISABLE);
+	}
+
+	/* check and set OE/Output-Enable mode */
+	regmap_read(priv->map, PWM_CV1800_OE, &state);
+	state &= PWM_CV1800_OE_MASK(pwm->hwpwm);
+
+	if (state == PWM_CV1800_REG_DISABLE && enable)
+		regmap_update_bits(priv->map, PWM_CV1800_OE,
+				   PWM_CV1800_OE_MASK(pwm->hwpwm),
+				   PWM_CV1800_REG_ENABLE(pwm->hwpwm));
+
+	return 0;
+}
+
+static void cv1800_pwm_set_polarity(struct pwm_chip *chip,
+				    struct pwm_device *pwm,
+				    enum pwm_polarity polarity)
+{
+	struct cv1800_pwm *priv = to_cv1800_pwm_dev(chip);
+	u32 config_polarity = 0;
+
+	if (pwm->state.enabled)
+		cv1800_pwm_enable(chip, pwm, !pwm->state.enabled);
+
+	if (polarity == PWM_POLARITY_NORMAL)
+		config_polarity = PWM_CV1800_POLARITY_MASK(pwm->hwpwm);
+
+	regmap_update_bits(priv->map, PWM_CV1800_POLARITY,
+			   PWM_CV1800_POLARITY_MASK(pwm->hwpwm),
+			   config_polarity);
+}
+
+static int cv1800_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+			    const struct pwm_state *state)
+{
+	struct cv1800_pwm *priv = to_cv1800_pwm_dev(chip);
+	u32 period_val, hlperiod_val;
+	u64 ticks;
+	u32 state;
+
+	if (state->polarity != pwm->state.polarity)
+		cv1800_pwm_set_polarity(chip, pwm, state->polarity);
+
+	/*
+	 * This hardware use PERIOD and HLPERIOD registers to represent PWM waves.
+	 *
+	 * The meaning of PERIOD is how many clock cycles (from the clock source)
+	 * are used to represent PWM waves.
+	 * PERIOD = rate(MHz) / target(MHz)
+	 * PERIOD = period(ns) * rate(Hz) / NSEC_PER_SEC
+	 */
+	ticks = mul_u64_u64_div_u64(state->period, priv->clk_rate,
+				    NSEC_PER_SEC);
+	if (ticks < PWM_CV1800_MINPERIOD)
+		return -EINVAL;
+
+	if (ticks > PWM_CV1800_MAXPERIOD)
+		ticks = PWM_CV1800_MAXPERIOD;
+	period_val = (u32)ticks;
+
+	/*
+	 * After mapping, hlperiod represents the same polarity as duty.
+	 * HLPERIOD = rate(MHz) / duty(MHz)
+	 * HLPERIOD = duty(ns) * rate(Hz) / NSEC_PER_SEC
+	 */
+	ticks = mul_u64_u64_div_u64(state->duty_cycle, priv->clk_rate,
+				    NSEC_PER_SEC);
+	if (ticks > period_val)
+		ticks = period_val;
+	hlperiod_val = (u32)ticks;
+
+	regmap_write(priv->map, PWM_CV1800_PERIOD(pwm->hwpwm), period_val);
+	regmap_write(priv->map, PWM_CV1800_HLPERIOD(pwm->hwpwm), hlperiod_val);
+
+	cv1800_pwm_enable(chip, pwm, state->enabled);
+
+	return 0;
+}
+
+static int cv1800_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
+				struct pwm_state *state)
+{
+	struct cv1800_pwm *priv = to_cv1800_pwm_dev(chip);
+	u32 period_val, hlperiod_val;
+	u64 period_ns = 0, duty_ns = 0;
+	u32 enable = 0, polarity = 0;
+
+	regmap_read(priv->map, PWM_CV1800_PERIOD(pwm->hwpwm), &period_val);
+	regmap_read(priv->map, PWM_CV1800_HLPERIOD(pwm->hwpwm), &hlperiod_val);
+
+	if (period_val != PWM_CV1800_PERIOD_RESET ||
+	    hlperiod_val != PWM_CV1800_HLPERIOD_RESET) {
+		period_ns = DIV_ROUND_UP_ULL(period_val * NSEC_PER_SEC,
+					     priv->clk_rate);
+		duty_ns = DIV_ROUND_UP_ULL(hlperiod_val * NSEC_PER_SEC,
+					   priv->clk_rate);
+
+		regmap_read(priv->map, PWM_CV1800_START, &enable);
+		enable &= PWM_CV1800_START_MASK(pwm->hwpwm);
+
+		regmap_read(priv->map, PWM_CV1800_POLARITY, &polarity);
+		polarity &= PWM_CV1800_POLARITY_MASK(pwm->hwpwm);
+	}
+
+	state->period = period_ns;
+	state->duty_cycle = duty_ns;
+	state->enabled = enable;
+
+	/*
+	 * To ensure that duty and hlperiod represent the same polarity
+	 * the following mapping needs to be completed.
+	 *
+	 * |----------|------------|------------|-----------|
+	 * |  Linux   |  register  |    duty    | register  |
+	 * | polarity |  polarity  |            | hlperiod  |
+	 * |----------|------------|------------|-----------|
+	 * |    1     |      0     | low level  | low level |
+	 * |----------|------------|------------|-----------|
+	 * |    0     |      1     | high level | high level|
+	 * |----------|------------|------------|-----------|
+	 */
+	state->polarity = polarity ? PWM_POLARITY_NORMAL :
+					   PWM_POLARITY_INVERSED;
+
+	return 0;
+}
+
+static const struct pwm_ops cv1800_pwm_ops = {
+	.apply = cv1800_pwm_apply,
+	.get_state = cv1800_pwm_get_state,
+};
+
+static int cv1800_pwm_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct cv1800_pwm *priv;
+	struct pwm_chip *chip;
+	void __iomem *base;
+	int ret;
+
+	chip = devm_pwmchip_alloc(dev, PWM_CV1800_CHANNELS, sizeof(*priv));
+	if (!chip)
+		return PTR_ERR(chip);
+	priv = to_cv1800_pwm_dev(chip);
+
+	base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	priv->map = devm_regmap_init_mmio(&pdev->dev, base,
+					  &cv1800_pwm_regmap_config);
+	if (IS_ERR(priv->map))
+		return PTR_ERR(priv->map);
+
+	priv->clk = devm_clk_get_enabled(&pdev->dev, NULL);
+	if (IS_ERR(priv->clk))
+		return dev_err_probe(&pdev->dev, PTR_ERR(priv->clk),
+				     "clk not found\n");
+
+	ret = devm_clk_rate_exclusive_get(dev, priv->clk);
+	if (ret)
+		return dev_err_probe(&pdev->dev, ret,
+				     "failed to get exclusive rate\n");
+
+	priv->clk_rate = clk_get_rate(priv->clk);
+	if (!priv->clk_rate)
+		return dev_err_probe(&pdev->dev, -EINVAL,
+				     "Invalid clock rate: %lu\n",
+				     priv->clk_rate);
+
+	chip->ops = &cv1800_pwm_ops;
+
+	ret = devm_pwmchip_add(dev, chip);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to add PWM chip\n");
+
+	return 0;
+}
+
+static const struct of_device_id cv1800_pwm_dt_ids[] = {
+	{ .compatible = "sophgo,cv1800-pwm" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, cv1800_pwm_dt_ids);
+
+static struct platform_driver cv1800_pwm_driver = {
+	.probe = cv1800_pwm_probe,
+	.driver	= {
+		.name = "cv1800-pwm",
+		.of_match_table = cv1800_pwm_dt_ids,
+	},
+};
+module_platform_driver(cv1800_pwm_driver);
+
+MODULE_AUTHOR("Jingbao Qiu");
+MODULE_DESCRIPTION("Sophgo cv1800 PWM Driver");
+MODULE_LICENSE("GPL");