mbox series

[v6,0/3] pinctrl: scmi: support i.MX95 OEM extensions

Message ID 20240513-pinctrl-scmi-oem-v3-v6-0-904975c99cc4@nxp.com (mailing list archive)
Headers show
Series pinctrl: scmi: support i.MX95 OEM extensions | expand

Message

Peng Fan (OSS) May 13, 2024, 11:45 a.m. UTC 
Hi Sudeep, Linus
  Is it possible for you to pick up this patchset earlier if no major
  comments?

Thanks,
Peng.

ARM SCMI v3.2 Table 24 Pin Configuration Type and Enumerations:
'192 -255 OEM specific units'.

i.MX95 System Manager FW supports SCMI PINCTRL protocol, but it has zero
functions, groups. So pinctrl-scmi.c could not be reused for i.MX95.
Because nxp,pin-func, nxp,pin-conf properties are rejected by dt
maintainers, so use generic property 'pinmux' which requires a new driver
pinctrl-imx-scmi.c

The node will be as below:
 pinctrl_usdhc1: usdhc1-pins {
         sd1-grp0 {
                 pinmux = <IMX95_PAD_SD1_CLK__USDHC1_CLK
                           IMX95_PAD_SD1_STROBE__USDHC1_STROBE>;
                 drive-strength = <0xe>;
                 input-schmitt-enable;
                 bias-pull-down;
                 slew-rate = <0x3>;
         };
         sd1-grp1 {
                 pinmux = <IMX95_PAD_SD1_CMD__USDHC1_CMD
                           IMX95_PAD_SD1_DATA0__USDHC1_DATA0
                           IMX95_PAD_SD1_DATA1__USDHC1_DATA1
                           IMX95_PAD_SD1_DATA2__USDHC1_DATA2
                           IMX95_PAD_SD1_DATA3__USDHC1_DATA3
                           IMX95_PAD_SD1_DATA4__USDHC1_DATA4
                           IMX95_PAD_SD1_DATA5__USDHC1_DATA5
                           IMX95_PAD_SD1_DATA6__USDHC1_DATA6
                           IMX95_PAD_SD1_DATA7__USDHC1_DATA7>;
                 drive-strength = <0xe>;
                 input-schmitt-enable;
                 bias-pull-up;
                 slew-rate = <0x3>;
         };
 };

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
Changes in v6:
- Per Andy comment to v4,
  drop imx_pin_group wrapper; assign sdev->handle to handle first, then check
  handle.
- Rebased to next-20240513
- Link to v5: https://lore.kernel.org/r/20240508-pinctrl-scmi-oem-v3-v5-0-6f2b167f71bc@nxp.com

Changes in v5:
- Added Rob'r R-b in patch 1 after addressed the comments
- Per Rob, use of_machine_compatible_match for patch 2
- Use of_machine_compatible_match for patch 3, and enable COMPILE_TEST
- Link to v4: https://lore.kernel.org/r/20240505-pinctrl-scmi-oem-v3-v4-0-7c99f989e9ba@nxp.com

Changes in v4:
- Rebase to next-20240503
- Add pinctrl-scmi-imx.c itself get pins and scmi pinctrl structure to decouple
  pinctrl-scmi.c and pinctrl-scmi-imx.c, so drop patch 3,4,5.
- Link to v3: https://lore.kernel.org/r/20240428-pinctrl-scmi-oem-v3-v3-0-eda341eb47ed@nxp.com

Changes in v3:
- patch 2,3,4,5 are new.
- Rewrite the binding, drop nxp,pin-x properties, use generic properties
  as Rob commented.
- Switch to using pinmux means pinctrl-scmi.c could not be reused, so
  add a new driver in patch 6 for i.MX95. But pinctrl_scmi_get_pins and
  scmi_pinctrl are exported for i.MX95 usage.
- Link to v2: https://lore.kernel.org/r/20240418-pinctrl-scmi-oem-v1-v2-0-3a555a3c58c3@nxp.com

Changes in v2:
- Rename nxp,imx95-pinctrl.yaml  to nxp,imx95-scmi-pinctrl.yaml and move
  to firmware
- Merged patch [1,2]/3 v1 into patch 1/2 v2.
- nxp,imx95-scmi-pinctrl.yaml only has patterProperties for subnode
  The pinctrl will be as below for i.MX95.
        pinctrl_usdhc1: usdhc1-pins {
                sd1cmd {
                        pins = "sd1cmd";
                        nxp,func-id = <0>;
                        nxp,pin-conf = <0x138e>;
                };
                sd1data {
                        pins = "sd1data";
                        nxp,func-id = <0>;
                        nxp,pin-conf = <0x138e>;
                };
        };
- Add pins enum, correct description.
- Link to v1: https://lore.kernel.org/r/20240412-pinctrl-scmi-oem-v1-v1-0-704f242544c1@nxp.com

---
Peng Fan (3):
      dt-bindings: firmware: arm,scmi: Add properties for i.MX95 Pinctrl OEM extensions
      pinctrl: scmi: add blocklist
      pinctrl: imx: support SCMI pinctrl protocol for i.MX95

 .../devicetree/bindings/firmware/arm,scmi.yaml     |   9 +-
 .../bindings/firmware/nxp,imx95-scmi-pinctrl.yaml  |  41 ++
 drivers/pinctrl/freescale/Kconfig                  |   9 +
 drivers/pinctrl/freescale/Makefile                 |   1 +
 drivers/pinctrl/freescale/pinctrl-imx-scmi.c       | 579 +++++++++++++++++++++
 drivers/pinctrl/pinctrl-scmi.c                     |   9 +
 6 files changed, 645 insertions(+), 3 deletions(-)
---
base-commit: ca45a28e860e3ed34cff0ce5211014d535bf6d6d
change-id: 20240428-pinctrl-scmi-oem-v3-12130031a74d

Best regards,

Comments

Sudeep Holla May 13, 2024, 1:24 p.m. UTC | #1 
On Mon, May 13, 2024 at 07:45:23PM +0800, Peng Fan (OSS) wrote:
> Hi Sudeep, Linus
>   Is it possible for you to pick up this patchset earlier if no major
>   comments?
>

FYI, it is the start of the merge window for v6.10. Any new feature
planned to be merged for v6.10 must be already in linux-next and anything
else need to wait for v6.11.

In short, this is not a v6.10 material and please wait until -rc1.

--
Regards,
Sudeep